Date post: | 18-Dec-2015 |
Category: |
Documents |
Upload: | lucianvoinica29373 |
View: | 235 times |
Download: | 26 times |
30
Section 7: Drawings and Parts List for Mongoose PT Assemblies
1
23
4
5
Figure 29: Mongoose Assembly Side Detail
Note: Item 2 shown above may not be the same as supplied
Item Number Qty Description Part Number
1 1 Mongoose PT Less Motors (See Section 9) 9671735
2 1 Control Assembly Kit For Mongoose PT See Table 1
3 2 Motor Linear See Table 1
4 1 Motor Elliptical See Table 1
5 1 Bypass Assembly Mongoose PT See Table 1
Figure 30: Parts List for Mongoose Assemblies
Configurations Item #2 Item #3 Item #4 Item #5 Configuration Description
9671740-01 9671693 EM3C00011 - - PT, 2 Motor, 460V, 60 Hz
9671740-02 9671688 EM3C00011 6912002 - PT, 3 Motor, 460V, 60 Hz
9671740-03 9671693 EM3C00011 - 9671734 PT, 2 Motor, w/ Bypass,460V, 60 Hz
9671740-04 9671688 EM3C00011 6912002 9671734 PT, 3 Motor, w/ Bypass, 460v, 60 Hz
9671740-05 9671693-01 EM3C00010 - - PT, 2 Motor, 400V, 50 Hz
9671740-06 9671688-02 EM3C00010 6905003 - PT, 3 Motor, 380V, 50 Hz
9671740-07 9671693-01 EM3C00010 - 9671734 PT, 2 Motor, w/ Bypass, 50 Hz
9671740-08 9671688-02 EM3C00010 6905003 9671734 PT, 3 Motor, w/ Bypass, 380V, 50 Hz
Table 1: Parts List for Mongoose Configurations
31
Section 7.1: Control Assembly Kit (9671693 and 9671693-01)
4 2 3
4
2
3423
4 2 3
8
8
8
8
7
5
6
7
5
6
5 6
ON BOTTOM OF ITEM 1
56
ON BOTTOM OF ITEM 1
1
11
A B C D
SEE CABLE ROUTING VIEW
12
Figure 31: Control Assembly Kit (9671693 and 9671693-01)
Item Number Qty Description Part Number
1 1 Starter 230/460V, 60 Hz 01-2213
2 4 Lockwasher, 1 05-110
3 4 Conduit Locknut, NPT 01-184
4 4 Cord Grip Straight 01-106
5 4 Reducer Bushing, MPT x FPT 5008937
6 4 Cable Connector, NPT .51-.81 Armored 6560030
7 2 Conduit Elbow, 90 Deg. MPT x FPT 5030937
8 4 Decal Label Rotation 9650367
9 40 ft. Cable Armored 4 Conductor, UL Approved 7906218
10 n/a n/a n/a
11 n/a n/a n/a
**12 1 Starter 380V, 50 Hz 01-2293
Figure 32: Parts List for (9671693 and 9671693-01)
** = Item Numbers 2 thru 9 are same for Control Assembly Kits 9671693 and 9671693-01.
Control Assembly Kit 9671693-01 (380/415V, 50 Hz) uses Item 12.
32
For proper supporting of motor cable see Cable Routing View and Table 1 below
CABLE #1APPROX. LENGTH: 46" LG. FROM TOWER CABLE GRIP TO MOTOR
CABLE #2APPROX. LENGTH: 44" LG. FROM TOWER CABLE GRIP TO MOTOR
A
BC D
Cable Routing View
Note: Grounding wire not shown
CABLE #2 7 7 6.5 8 7
CABLE #1 11.5 7 6.5 8 7
MOTOR TO A A TO B B TO C C TO D D TO TOWER
APPROX. LENGTH OF CABLE (INCHES)
Table 1
33
Section 7.2: Control Assembly Kit (9671688 and 9671688-02)
11
11
11 11
11
11
2
7 8
ON BOTTOM OF ITEM 2
12
12
12
10
6 4 5
6 4 5
645
6 4 5
6 4 5
6
4
5
978
978
7 8
A B C DE
SEE CABLE ROUTING VIEW
78
78
1
16132x
1415
Figure 33: Control Assembly Kit (9671688)
Item Number Qty Description Part Number
1 1 Plate, Control Panel Mounting Adapter 9671689
2 1 Starter Assembly 460 V, 60 Hz 7584916
*2a 1 Starter Assembly 380 V, 50 Hz 6930007
3 4 Mount Vibration Donut 5859378
4 6 Lockwasher, 1 05-110
5 6 Conduit Locknut, NPT 01-184
6 6 Cord Grip Straight 01-106
7 6 Reducer Bushing, MPT x FPT 5008937
8 6 Cable Connector, NPT .51-.81 Dia. Armored 6560030
9 2 Conduit Elbow, 90 Deg. x FPT 5030937
10 n/a n/a n/a
11 6 Decal, Arrow Rotation 9650367
12 60 ft. Cable Armored 4 Conductor, UL Approved 7906218
13 8 Flatwasher, M12 Regular, SST 05-305
14 4 Lockwasher, M12 Regular, SST 05-306
15 4 Hex Nut, M12, SST 03-415
16 4 HHCS, M12 x 80 mm Lg., SST 04-1147
Figure 34: Control Assembly Kit 9671688, 9671688-02
* = Starter Assembly is for 9671688-02 only, Items 1, 3-16 will the same for both
Configurations.
34
For proper supporting of motor cable see Cable Routing View and Table 1 below
CABLE #1
CABLE #2
CABLE #3
AB C D
E
25REF
Cable Routing View
CABLE #3 5.5 6 6 6 7 4.5 35
CABLE #2 13.5 6 6 6 7 6.5 45
CABLE #1 15 6 6 6 7 6 46
MOTOR TO A
A TO B
B TO C
C TO D
D TO E
E TO TOWER
TOTALLENGTH
APPROXIMATE LENGTH OF CABLE (INCHES)
Table 1
35
Section 8: Drawings and Parts List For Mongoose PT Assembly (9671735 Shaker
Assembly Less Motors and Controls)
See Following Drawing
BILL OF MATERIAL
5950 NORTH COURSE DRIVE, HOUSTON, TEXAS 77072
UNLESS OTHERWISE SPECIFIED: DATE
DRAWN
SIGNATURES
CHECKED
ENGINEER
APPROVED
NEXT ASSY TOP ASSY
SHEET SCALE SIZE DRAWING NO. REV
DIMENSIONS ARE IN INCHESMILLIMETERS ARE IN BRACKETSDO NOT SCALE PRINTSREMOVE BURS AND SHARP EDGESSURFACE ROUGHNESS 125 MICRO INCHES RMSTOLERANCES PER ANSI Y14.5MTHIRD ANGLE PROJECTIONTOLERANCES ON:.XXX +/- .005 FRAC +/- 1/32
.XX +/- .015 ANG +/- 1/2 DEG
.X +/- .031 CONCEN .005 DIA
CONFIDENTIAL
THIS DRAWING AND / OR SPECIFICATION EMBODIESCONFIDENTIAL INFORMATION OF SWACO, A DIVISIONOF M-I L.L.C., IN THE ABSENCE OF EXPRESS WRITTENPERMISION. SWACO HAS LOANED THIS COPY WITH THEUNDERSTANDING THAT (A) IT WILL NOT BE REPRODUCED(B) IT WILL NOT BE USED FOR ANY PURPOSE EXCEPT
THAT FOR WHICH IT WAS LOANED AND (C) IT WILL BERETURNED ON DEMAND OR UPON COMPLETION OFTHE CONTRACTED WORK, WHICH EVER COMES FIRST.
ACKNOWLEDGED: ______________ DATE: _____________
F
I
L
E
N
A
M
E
:
S
w
a
c
o
D
M
a
c
h
i
n
e
d
D
ISO VIEW
JAM 3/22/04
SHAKER, MONGOOSE PT LESSMOTORS AND CONTROLS
W/ BOLT ON FLANGES
F96717351 OF 3 NTS
NOTES:
1. WHEN A BY-PASS ASSEMBLY IS BOLTED TO 9671735, THEN ITEM NUMBERS #33-#38 ARE TO BE SHIPPED LOOSE WITH THE SHAKER.2. IF THE .60 HP MOTOR IS NOT USED, THEN ITEM NUMBERS #26, #27, #28 AND #30 ARE TO BE SHIPPED LOOSE WITH THE SHAKER.3. USE FOOD GRADE ANTI-SIEZE (LOCTITE 51168) ON ALL BOLTS AND SCREWS EXCEPT MOTOR MOUNTING HARDWARE (ITEMS #7 & #28).4. ITEM 41 NOT SHOWN.
BSC 4/7/04
9671740 9671740
FI
L
E
N
A
M
E
:
S
w
a
c
o
D
2
5950 NORTH COURSE DRIVE, HOUSTON, TEXAS 77072REVDRAWING NO.SIZESHEETSCALE
D
D
D
SECTION D-D
E
DETAIL E
4
13
1416
1
3
GG
17
3
21
NTS 2 OF 3
J J
SECTION J-J
K
DETAIL K
35
333634
13
F9671735
SECTION G-G
725 26
28
2730624
37
4242
42 42
3837
1
C
DETAIL C
34 33 37 3536 38 37
FI
L
E
N
A
M
E
:
S
w
a
c
o
D
2
5950 NORTH COURSE DRIVE, HOUSTON, TEXAS 77072REVDRAWING NO.SIZESHEETSCALE
D
RIGHT SIDE
AB
DETAIL A
22
13
14
1
20
20
DETAIL B
4
13
14
19
20
5
18
2
1
3
20
5
18
H
DETAIL H18
29
29
2
15
23
NTS 3 OF 3
31
32
16
F9671735
FDETAIL F
12
11
2
2
9
1
10
11
12
LIFTING LUG HIDDEN FOR CLARITY
39 408
LEFT SIDE
L
1
2
15
5
21
188
17
3
33
40
3939
DETAIL L
18
5
4
13
21
19
19
14
16
41
ITEM 41 NOT SHOWN
43
43
ITEMS 33-38 HIDDEN FOR CLARITY
36
Section 8, cont.
Item Number Qty Description Part Number
1 1 Weldment, Skid Mongoose 9671770
2 1 Assembly, Mongoose Basket 9671738-01
3 1 Weldment, Header Box 9671810
4 16 HHCS M12 x 45 mm Lg. 04-1270
5 2 Jack, Elevator 9671681
6 8 Nut, Hex M20-1.5, Grd 10.9, Yellow Chromate 1305055
7 8 HHCS M20-1.5 x 120 mm Lg., Grd. 10.9 1407169
8 2 Gate, Skid Slide 9671779
9 4 Bracket, Shipping (ATEX, CE) 9671742
10 8 Flatwasher, M20 05-296
11 8 Lockwasher, M20 05-307
12 8 HHCS M20-2.5 x 70 mm Lg. 04-1629
13 32 Flatwasher, M12 Reg. 05-305
14 24 Lockwasher, 12 Reg. 05-306
15 2 Decal, Swaco 8420202
16 16 Hex, Nut M12 03-415
17 2 10 Inspection Cover S48B00829
18 2 Spring Spool Weldment 9671679
19 2 Indicator Pointer 9671683
20 1 Plate, Right Indicator 9671744
21 1 Plate, Left Indicator 9671745
22 8 HHCS M12 x 30 Lg. 04-1157
23 4 Spring Coil 9360007
24 8 Lockwasher Schnorr M20 Martin #513014 05-244
25 8 Motor Washer BM6S80043-01
26 4 Washer, 16 mm Motor 9671682
27 4 Lockwasher Schnorr M16 05-248
28 4 HHCS M16 x 1.5 x 100 mm Lg. 1407144
29 8 Washer, Spring Isolation 5895002
30 4 Nut, Hex M16-1.5, Yellow Chromate 1305040
31 1 Unit Tag 9650360
32 4 Pop Rivet, 1/8 07-409
33 2 Cover, Weld Flange 10, MS 9671652-01
34 2 Gasket, Ring ANSI Flange RF, 150 LB, 10 3916067
35 24 HHCS M24-3.0 x 90 mm, Yellow Chromate 1493003
36 24 Hex, Nut M24 03-412
37 48 Flatwasher, M24 05-308
38 24 Lockwasher, M24 05-309
39 4 Label, Lift Point BM6K80098
40 2 Label, PE Protective Earth BMK80097
41 4 Boot, Spring 5804004
42 4 Decal Shipping Bracket 9650511
43 2 Cover, Plug-I/O 6 inch Dia. Nitrile S48K00827-NL
Figure 35: Parts List for (9671735)
* = Item is not shown for clarity
*** = Are shipped loose with shaker if third (3) motor arrangement is not used.
37
Section 9: Drawings and Parts List For Mongoose PT Basket Assembly (9671738-01 thru -03)
See Following Drawing
BILL OF MATERIAL
5950 NORTH COURSE DRIVE, HOUSTON, TEXAS 77072
Swaco, A Division of M - I L.L.C.
UNLESS OTHERWISE SPECIFIED: DATE
DRAWN
SIGNATURES
CHECKED
ENGINEER
APPROVED
NEXT ASSY TOP ASSY
SHEET SCALE SIZE DRAWING NO. REV
DIMENSIONS ARE IN INCHESMILLIMETERS ARE IN BRACKETSDO NOT SCALE PRINTSREMOVE BURS AND SHARP EDGESSURFACE ROUGHNESS 125 MICRO INCHES RMSTOLERANCES PER ANSI Y14.5MTHIRD ANGLE PROJECTIONTOLERANCES ON:.XXX +/- .005 FRAC +/- 1/32
.XX +/- .015 ANG +/- 1/2 DEG
.X +/- .031 CONCEN .005 DIA
CONFIDENTIAL
THIS DRAWING AND / OR SPECIFICATION EMBODIESCONFIDENTIAL INFORMATION OF SWACO, A DIVISIONOF M-I L.L.C., IN THE ABSENCE OF EXPRESS WRITTENPERMISION. SWACO HAS LOANED THIS COPY WITH THEUNDERSTANDING THAT (A) IT WILL NOT BE REPRODUCED(B) IT WILL NOT BE USED FOR ANY PURPOSE EXCEPT
THAT FOR WHICH IT WAS LOANED AND (C) IT WILL BERETURNED ON DEMAND OR UPON COMPLETION OFTHE CONTRACTED WORK, WHICH EVER COMES FIRST.
ACKNOWLEDGED: ______________ DATE: _____________
F
I
L
E
N
A
M
E
:
S
w
a
c
o
D
M
a
c
h
i
n
e
d
D
ISO VIEW
JAM 03/22/04
BASKET ASSEMBLY,MONGOOSE FLAT PANEL
C9671738-011 OF 2 NTS
1
AA
D D
E9
2
1
NOTES: 1. USE SUPERFLEX TM RED RTV SILICONE ADHESIVE (MI-Swaco P/N: 00-1589 OR EQUIVALENT ON THE FEED END SKIRT IF REMOVED OR REPLACED. 2. USE FOOD GRADE ANTI-SEIZE (LOCTITE 51168) ON ALL BOLTS AND SCREWS IF REMOVED.
BSC 04/7/04
9671738-01 BASKET ASSEMBLY, MS BASKET AND 304SS HARDWARE
CONFIGURATION DESCRIPTION
G G
4 5 6 7 24
4 5 6 7 24
SEE SECTION G-GON SHEET 2
SEE SECTION G-GON SHEET 2
FI
L
E
N
A
M
E
:
S
w
a
c
o
D
2
5950 NORTH COURSE DRIVE, HOUSTON, TEXAS 77072REVDRAWING NO.SIZESHEETSCALE
Swaco, A Division of M - I L.L.C.
D2 OF 2 9671738-01NTS
SECTION A-A
B
DETAIL B
C
DETAIL C
5
4
1
12
4
7
6
5
4
2
9
1
6
7
1
12
3
33
3
SECTION D-D
10 11 14
13
DETAIL E
1011
14
F
DETAIL F
5
4
2
9
8
6
7
1
ADD HIGH TEMP REDSILICONE AROUNDTHE PERIMETER OFTHE REMOVABLECOVER
ADD HIGH TEMP REDSILICONE AROUNDTHE PERIMETER OFTHE REMOVABLECOVER
C
15
SECTION G-G
H
DETAIL H
5
4
24
67
2
9
38
ConfigurationsItem
# -01 -02 -03 Description Qty
1 9674610 9671610-01 9671610-02 Weldment, Mongoose Basket 1
2 9671637-02 9671637-01 9671637-02 Cover, Removable 1
3 5895001 5895001 5895001 Wedge, Mongoose Screen 8
4 05-277 05-317 05-277 Flatwasher, M10 38
5 04-1103 04-1213 04-1103 HHCS M10 x 30 mm Lg. 30
6 05-270 05-316 05-270 Lockwasher, M10 30
7 03-229 03-300 03-229 Hex Nut M10 30
8 9671638-02 9671638-01 9671638-02 Bar, Skirt Retainer 1
9 5873004 5873004 5837004 Skirt, Feed End 1
10 5837001 5837001 5837001 Gasket, Mongoose PT Screen 4
11 9671640 9671640-01 9671640 Weldment, Screen Bar 4
12 9671925 9671925 9671925 Drip Lip Mongoose PT 1
13 07-415 07-415 07-415 Grommet Screw .273 Sq. Panel Hole 32
14 1441471 1441471 1441471 #8 Flat Head Sheet Metal Screw w/ Sq.
Drive32
15 BM6K80100 BM6K80100 BM6K80100 Label, Crush Hands 1
24 05-217 05-217 05-217 Flatwasher 1/2 304 SS 1.38 O.D 1/2 I.D
x 12 GA Thk. 2
Figure 36: 9671738-01 thru -03 Parts List
39
Section 10: Recommended Spare Parts
Note: Spares are for one (1) unit only
Note 1: Item 9 is only required if Configurations 9671740-01 thru -04 are supplied.
Note 2: Item 10 is only required if Configurations 9671740-02, -04 are supplied.
Note 3: Item 11 is only required if Configurations 9671740-05, -07 are supplied.
Note 4: Item 12 and 13 are only required if Configurations 9671740-01, -03, -05, -07 are supplied.
Note 5: Item 14 and 15 are only required if Configurations 9671740-02, -04 are supplied.
Note 6: Items 23 thru 25 and 27 are only required if Configurations 9671740-02, -04 are supplied.
Note 7: Items 35 thru 50 are only required if Configurations 9671740-02, -04, -07 are supplied.
Note 8: Items 51 thru 56 are only required if Configurations 9671740-01, -03, -05 are supplied.
Note 9: Items 57 thru 70 are only required if Configurations 9671740-06, -08 are supplied.
40
Section 10, cont.
See Note /
Item
Figure No. /
Item No. Qty Part Number Description
n/a / 1 21 / n/a 1 JMONMKO2OP Screen 10 Mesh
n/a / 2 21 / n/a 1 JMONMKO6OP Screen 60 Mesh
n/a / 3 21 / n/a 1 JMONMXO84P Screen 60 Mesh
n/a / 4 21 / n/a 1 JMONMX110P Screen 110 Mesh
n/a / 5 21 / n/a 1 JMONMX140P Screen 140 Mesh
n/a / 6 21 / n/a 1 JMONMX175P Screen 175 Mesh
n/a / 7 21 / n/a 1 JMONMX210P Screen 210 Mesh
n/a / 8 21 / n/a 1 JMONMX250P Screen 250 Mesh
1 / 9 30 / 3 2 EM3C00011 Motor 2 Hp, 230/460 V, 60 Hz
2 / 10 30 / 4 1 6912002 Motor 0.60 Hp, 230/460 V, 60 Hz
3 / 11 30 / 5 2 EM3C00010 Motor 2 Hp, 380/415 V, 50 Hz
4 / 12 32 / 6 4 6560030 Cable Connector 1/2 NPT .51-.81
Armored
4 / 13 32 / 9 40 ft. 7906218 Cable Armored 4 Conductor, UL
Approved
5 / 14 34 / 8 6 6560030 Cable Connector 1/2 NPT .51-.81
Armored
5 / 15 34 / 12 60 ft. 7906218 Cable Armored 4 Conductor, UL
Approved
n/a / 16 35 / 5 2 9671681 Jack, Elevator
n/a / 17 35 / 6 8 1305055 Nut Hex M20-1.5, Grd. 10.9, Yellow
Chromate
n/a / 18 35 / 7 8 1407169 HHCS M20-1.5 x 120 mm Lg., Grd
10.9
n/a / 19 35 / 17 2 S48B00829 10 Inspection Cover
n/a / 20 35 / 23 4 936007 Spring Coil
n/a / 21 35 / 24 8 05-244 Lockwasher Schnorr M20 Martin
#513014
n/a / 22 35 / 25 8 BM6S80043-01 Motor Washer
6 / 23 35 / 26 4 9671682 Washer, M16 Motor
6 / 24 35 / 27 4 05-248 Lockwasher Schnorr M16
6 / 25 35 / 28 4 1407144 HHCS M16-1.5 x 100 mm Lg.
n/a / 26 35 / 29 8 5895002 Washer, Spring Isolation
6 / 27 35 / 30 4 1305040 Nut Hex M16-1.5, Yellow Chromate
n/a / 28 35 / 41 4 5804004 Boot Spring
41
Section 10, cont.
See Note /
Item
Figure No. /
Item No. Qty Part Number Description
29 36 / 3 8 5895001 Wedge Mongoose Screen
30 36 / 9 1 5873004 Skirt, Feed End
31 36 / 10 4 5837001 Gasket, Mongoose PT Screen
32 36 / 12 1 9671925 Drip Lip Mongoose PT
33 36 / 13 32 07-415 Grommet Screw .73 Sq Panel Hole
34 36 /13 32 1441471 #8 Flat Head Sheet Metal Screw w/ Sq.
Drive
7 / 35 23 / 1 2 7518020 Shawmut Fuse
7 / 36 23 / 2 4 7150001 Cutler-Hammer Contactor
7 / 37 23 / 3 4 7150002 Cutler-Hammer Overload Block
7 / 38 23 / 4 2 7150003 Cutler-Hammer Aux. Contact
7 / 39 23 / 5 1 7150004 Cutler-Hammer Rev. Kit
7 / 40 23 / 6 1 7518021 Hammond Fuse Kit
7 / 41 23 / 7 2 7152605 Cutler-Hammer Overload Heaters
7 / 42 23 / 8 2 7152606 Cutler-Hammer Overload Heaters
7 / 43 23 / 9 1 7518022 Shawmut Fuse
7 / 44 23 / 10 1 7790015 Hammond Transformer
7 / 46 23 / 12 1 7573105 Adalet Emergency Push-Pull
7 / 47 23 / 13 1 7573106 Adalet Selector Switch
7 / 48 23 / 14 2 7573290 Adalet Reset Button
7 / 49 23 / 15 1 7150005 A&B Power Block
7 / 50 23 / 16 1 7117005 Dayton Timer
8 / 51 28 / 1 1 7573333 Green Pushbutton
8 / 52 28 / 2 1 7573334 Red Pushbutton
8 / 53 28 / 3 2 7518023 1/2 amp Fuse
8 / 54 28 / 4 1 7150008 Contact, 460 V
8 / 55 28 / 5 1 7152003 Overload
8 / 56 28 / 6 1 7152004 Overload Mounting Base
42
Section 10, cont.
See Note /
Item
Figure No. /
Item No. Qty Part Number Description
9 / 57 23a / 1 2 7573290 Reset Button
9 / 58 23a / 2 1 7573106 Selector Switch
9 / 59 23a / 3 4 8071702 Mechanical Push Rod
9 / 60 23a / 4 1 7573105 E-Stop Push Pull
9 / 61 23a / 5 1 7790016 Transformer 380V
9 / 62 23a / 6 1 7117005 Timer
9 / 63 23a / 7 2 7150014 Power Distribution Block
9 / 64 23a / 8 2 7150001 Contactors Non-Rev.
9 / 65 23a / 9 1 6930009 Contactor-Reversing
9 / 66 23a / 10 4 7150002 Overload Blocks
9 / 67 23a / 11 2 7152605 Overload Heaters
9 / 68 23a / 12 2 7152606 Overload Heaters
9 / 69 23a / 13 1 7519002 Fuse Block
9 / 70 23a / 14 2 7518020 Fuse
9 / 71 23a / 15 1 7515022 Fuse