move-series - BRECOflex Co. · 2019-10-25 · 3 move-series® Advantages 3D Model Standard...

The World Leader In Polyurethane Timing Belts

B115

move-series®

The New Generation of Timing Belts

2 move-series®

move-series®

The New Generation of Timing Beltsmove-series® is a superior strength timing belt designed for high-performance drives. It is available as open-ended code M for linear drive applications and truly endless code BFX for power transmission applications. This new generation of timing belt delivers the power that modern applications require, with custom-engineered steel cord tension members and tooth geometry optimized through 3D motion FEA. This allows for up to 75% more tensile strength and reduces areas of high stress.

move-series® provides a durable solution, with a friction-optimizing laminate coating to minimize wear and increase service life. move-series® affords space and cost savings. With a higher transmittable force, belt drives can be more compact and powerful.

• 75% higher stiffness and tensile strength

• 30% higher transmittable force

• permits reducing the belt width by one standard size

• narrower drive reduces drive inertia and noise

• reduced wear and increased service life

• more chain to belt conversions possible

• significantly increases safety factor when staying with original width

A belt drive is often limited by the tooth shear strength. To reduce this limitation, BRECOflex analyzed the tooth geometry of standard AT-Series timing belts using 3D motion FEA (Finite Elements Analysis). The results yielded an optimized tooth geometry that reduces areas of high stress and makes the allowable belt load 30% greater than other AT-series belts. This optimal tooth geometry works with standard pulleys and will outperform when paired with high precision BRECOflex pulleys.

NOTE: BRECOflex CO., L.L.C. highly recommends the use of hard anodized aluminum pulleys for the longest service life.

Optimized Tooth Geometry

3

move-series®

Advantages

3D Model Standard move-series

Custom-engineered steel cord tension members deliver up to 75% more tensile strength compared to standard AT-series tension members.

Another unique property of the move timing belt is a special laminate coating that is used to further reduce friction between belt and pulley. This minimizes wear and ensures quiet tooth engagement, and smooth running.

Belt stiffness is the most important parameter in linear drives and is often the limit of drive accuracy. High move stiffness provides reduced settling times over the standard AT10 and AT15. When combined with our zero-backlash drive pulleys no belt comes close to the precision of move timing belts.

Unprecedented Cord Strength & Stiffness

4 move-series®

move-series®

AT10 Pitch Open-Ended “M”

Widths (mm)

Specifications

Standard Material

move Tension Member

Belt Color

TPUST1

25

Open-Ended ”M”

32 50 75 100

Steel

Lengths Any lengths available - Stock Rolls 50 Meters

White / Red

move-series® Flexibility(minimum tooth count/minimum diameter)

Power Comparison35

30

25

20

15

10

5

0

AT10 MOV AT10 HTD 8M

RPM

Pow

er [W

/cm

/toot

h]

0 500 1000 1500 2000 2500 3000 3500 4000

Construction

Open-Ended“M”

Tension-memberBelt Width (mm)

32 50 75 10025

AT10move Belt “M” Specifications

AT10-move Tension Member

Specific Stiffness

Belt Mass

7,395 9,135 14,790 22,185 29,580

1.85 - 106 2.28 - 106 3.70 - 106 5.55 - 106 7.40 - 10 6

Dimension

F [N]zul

C [N]spec

[kg/m/cm]

Construction

Open-Ended“M”


50 75 100 150


AT15move Tension Member

Specific Stiffness

Belt Mass

18,200 27,300 36,400 54,600

4.55 - 106 6.82 - 106 9.10 - 106 13.65 - 106

0.070 kg per meter of belt length per cm of belt width

Dimension

F [N]zul

C [N]spec

[kg/m/cm]

Construction

Truly Endless“BFX”

Tension-memberBelt Width (mm)32 50 75 10025

AT10move Belt “BFX” Specifications


Belt Mass

6,750 8,625 13,470 20,200 26,940

Dimension

[kg/m/cm]

F [N]zul

Construction Tension-memberBelt Width (mm)



Belt Mass

Dimension

F [N]zul

[kg/m/cm]


0.173 0.222 0.347 0.520 0.693

0.175 0.221 0.351 0.526 0.701

32 50 75 10025

8,450 11,050 17,550 26,000 35,100

0.237 0.303 0.473 0.710 0.946

Zmin

dmin

Zmin

dmin

Drive w/o back bending

Drive with back bending

Tension MemberConstructionZmin

dmin(mm)


dmin(mm)

AT15moveTension Member


M/BFX20

100

M/BFX25

120

Zmin

dmin

Zmin

dmin




dmin(mm)


dmin(mm)



M/BFX18

60

M/BFX25

120

5

move-series®


move-series AT10

AT10

0.300

0.200

0.100

0.000

-0.100

-0.200

-0.300

Dist

ance

[mm

]

Time [s]0.000 0.050 0.100 0.150 0.200 0.250 0.300 0.350 0.400

Settling Time

Open ended move-series® demonstrates its strengths particularly well in linear drive applications.This chart shows how the stiffness of move dramatically reduces settling time.

AT10move - M

R.P.M.n [min]

R.P.M.n [min]

FUSPEC[N/cm]

FUSPEC[N/cm]

AT10move RPM 0-1900 AT10move RPM 2000-10000

R.P.M.n [min]

R.P.M.n [min]

FUSPEC[N/cm]

FUSPEC[N/cm]

020406080100200300400500600700

113.2111.5110.0108.6107.2105.8100.195.691.688.485.582.7

800900

1000110012001300140015001600170018001900

80.478.276.274.472.771.169.668.266.865.664.463.1

200022002400260028003000320034003600380040004500

500055006000650070007500800085009000950010000

62.160.158.256.454.753.151.750.449.147.946.743.9

41.439.337.335.433.632.030.429.027.626.425.1

Ordering Example: move-series® Timing Belt[WIDTH] [PITCH] / [LENGTH] [CONSTRUCTION]

50 AT10 MOV / 3750 M

6 move-series®

move-series®

AT10 Pitch Truly Endless “BFX”

Widths (mm)

SpecificationsTruly Endless “BFX”

Standard Material

move Tension Member

Belt Color

TPUST1

25 32 50 75 100

Steel

LengthsStandard lengths listed below.

Additional lengths available up to 30,500mm. In between lengthsavailable starting at a minimum of 1,400mm.

White / Red

AT10move is a next generation timing belt with enhanced performance properties. It is available as open-ended code M for linear drive application and truly endless BFX for power transmission applications. Choose AT10move as a stiffer, more compact and longer lasting alternative to standard AT10, ATS15 and AT20 belts. Customers that switch from standard AT10 to move-series® see a significant increase in wear resistance, tensile strength, transmittable force and service life.

1080

840

980 1600

1400

1500 2120

780

1240

1800

1900

2000

720

1150

1700

2500

2360

2240

AT10move Standard Lengths (mm)

3750

3350

3550 5000

4500

4750 6700

6000

6300

8000

9000

3150

4250

5600

7500

4000

5300

7100

2800

2650

3000

In-between lengths available from 1,400 to 30,500mm

Pitch/LengthVersion

Numberof Teeth

AT10 MOV / 720 BFXAT10 MOV / 780 BFXAT10 MOV / 840 BFXAT10 MOV / 980 BFXAT10 MOV / 1080 BFXAT10 MOV / 1150 BFXAT10 MOV / 1240 BFXAT10 MOV / 1400 BFXAT10 MOV / 1500 BFXAT10 MOV / 1600 BFXAT10 MOV / 1700 BFXAT10 MOV / 1800 BFXAT10 MOV / 1900 BFX

72788498108115124140150160170180190

Pitch/LengthVersion

Numberof Teeth


200212224236250265280300315335355375400

Pitch/LengthVersion

Numberof Teeth


425450475500530560600630670710750800900

AT10move AT10move AT10move

Standard Lengths

7

move-series®


AT10move - BFX Tooth Shear Strength (specific belt tooth load bearing)

R.P.M.n [min ]

R.P.M.n [min ]

FUSPEC[N/cm]

M SPEC[Ncm/cm]

PSPEC[W/cm]

FUSPEC[N/cm]

M SPEC[Ncm/cm]

PSPEC[W/cm]

020406080

100200300400500600700800900

1000110012001300140015001600170018001900

200022002400260028003000320034003600380040004500500055006000650070007500800085009000950010000

113.2111.5110.0108.6107.2105.8100.195.691.688.485.582.780.478.276.274.472.771.169.668.266.865.664.463.1

18.0217.7617.5117.2617.0516.8515.9415.2214.6014.0613.6013.1712.8012.4412.1411.8411.5711.3211.0710.8410.6410.4410.2410.06

0.0000.3710.7331.0861.4291.7633.3424.7746.1147.3618.5479.65610.71811.73512.70513.64414.53815.40016.23217.04817.81818.57219.31220.020

62.160.158.256.454.753.151.750.449.147.946.743.941.439.337.335.433.632.030.429.027.626.425.1

9.899.559.268.988.728.478.248.017.817.617.426.996.616.255.935.625.345.084.854.624.404.194.00

20.69822.02223.25424.42425.53326.59627.59728.53629.42930.29231.10832.95634.65036.03637.26838.34639.27040.04040.65641.11841.42641.73441.888



50 AT10 MOV / 3750 BFX

Construction

Open-Ended“M”


32 50 75 10025



Specific Stiffness

Belt Mass

7,395 9,135 14,790 22,185 29,580

1.85 - 106 2.28 - 106 3.70 - 106 5.55 - 106 7.40 - 10 6

Dimension

F [N]zul

C [N]spec

[kg/m/cm]

Construction

Open-Ended“M”


50 75 100 150



Specific Stiffness

Belt Mass

18,200 27,300 36,400 54,600

4.55 - 106 6.82 - 106 9.10 - 106 13.65 - 106


Dimension

F [N]zul

C [N]spec

[kg/m/cm]

Construction





Belt Mass

6,750 8,625 13,470 20,200 26,940

Dimension

[kg/m/cm]

F [N]zul




Belt Mass

Dimension

F [N]zul

[kg/m/cm]


0.173 0.222 0.347 0.520 0.693

0.175 0.221 0.351 0.526 0.701

32 50 75 10025

8,450 11,050 17,550 26,000 35,100

0.237 0.303 0.473 0.710 0.946

8 move-series®

move-series®


Widths (mm)

Specifications

Standard Material

move Tension Member

Belt Color

TPUST1

25 32 50 75 100

Steel

Lengths Any lengths available - Stock Rolls 50 Meters

White / Red

Open-Ended ”M”

Construction

Open-Ended“M”


32 50 75 10025



Specific Stiffness

Belt Mass

7,395 9,135 14,790 22,185 29,580

1.85 - 106 2.28 - 106 3.70 - 106 5.55 - 106 7.40 - 10 6

Dimension

F [N]zul

C [N]spec

[kg/m/cm]

Construction

Open-Ended“M”


50 75 100 150



Specific Stiffness

Belt Mass

18,200 27,300 36,400 54,600

4.55 - 106 6.82 - 106 9.10 - 106 13.65 - 106


Dimension

F [N]zul

C [N]spec

[kg/m/cm]

Construction





Belt Mass

6,750 8,625 13,470 20,200 26,940

Dimension

[kg/m/cm]

F [N]zul




Belt Mass

Dimension

F [N]zul

[kg/m/cm]


0.173 0.222 0.347 0.520 0.693

0.175 0.221 0.351 0.526 0.701

32 50 75 10025

8,450 11,050 17,550 26,000 35,100

0.237 0.303 0.473 0.710 0.946

Zmin

dmin

Zmin

dmin




dmin(mm)


dmin(mm)



M/BFX20

100

M/BFX25

120

Zmin

dmin

Zmin

dmin




dmin(mm)


dmin(mm)



M/BFX18

60

M/BFX25

120

move-series® Flexibility(minimum tooth count/minimum diameter)

9

move-series®



50 AT15 MOV / 3750 M

Spec

ific

Stiff

ness

(10

N)

Belt Stiffness (based on a 50mm wide open-ended belt)

T10 AT10 AT10move ATL10 ATS15 AT20 ATL20

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

6 3.70

5.0

AT15move

4.60

AT15move - M Tooth Shear Strength (specific belt tooth load bearing)

R.P.M.n [min ]

R.P.M.n [min ]

FUSPEC[N/cm]

FUSPEC[N/cm]

020406080100200300400500600700

200022002400260028003000320034003600380040004500

168.0165.2162.7160.3157.9155.8146.5139.0132.8127.4122.6118.4

85.382.079.076.273.671.168.866.664.662.660.756.4


R.P.M.n [min ]

R.P.M.n [min ]

FUSPEC[N/cm]

FUSPEC[N/cm]

800900

1000110012001300140015001600170018001900

5000550060006500

114.6111.1107.9105.0102.299.797.395.092.990.888.987.1

52.549.045.842.8


R.P.M.n [min ]

R.P.M.n [min ]

FUSPEC[N/cm]

M SPEC[Ncm/cm]

PSPEC[W/cm]

FUSPEC[N/cm]

M SPEC[Ncm/cm]

PSPEC[W/cm]

0204060801002003004005006007008009001000110012001300140015001600170018001900

2000220024002600280030003200340036003800400045005000550060006500

168.0165.2162.6160.2157.9155.8146.5139.0132.8127.4122.6118.4114.6111.1107.9105.0102.299.797.395.092.990.888.987.1

40.139.438.838.237.737.235.033.231.730.429.328.227.326.525.725.024.423.823.222.722.121.721.220.8

0.0000.8271.6272.4053.1613.8987.332

10.43713.28815.93518.41120.73922.93925.02427.00728.89730.70132.42734.08035.66537.18738.64940.05541.407

85.382.079.076.273.671.168.866.664.662.660.756.452.549.045.842.8

20.319.618.818.217.516.916.415.915.414.914.513.412.511.710.910.2

42.70945.17147.45849.58451.56153.39955.10956.69758.17159.53860.80263.54765.75167.46868.74369.611


10 move-series®

move-series®

AT15 Pitch Truly Endless “BFX”The AT15move is the strongest polyurethane timing belt you can buy. It is specifically designed for heavy-duty high-performance drives and traction drives with a particularly high stiffness requirement. It is also made for linear drive applications where short settling times and high positioning accuracy are a necessity. The specially developed steel cord tension members increase belt stiffness and tear-resistance, making transmission of stronger forces possible. As with AT10move, you can select a narrower timing belt making a more compact drive design possible.

Widths (mm)

Specifications

Standard Material

move Tension Member

Belt Color

TPUST1

25 32 50 75 100

Steel

LengthsStandard lengths listed below.

Additional lengths available up to 30,495mm. In between lengthsavailable starting at a minimum of 1,410mm.

White / Red

Truly Endless “BFX”

19051710

1800 300025052790 4245

15902250

3495

37504005

1500

19953285

499547404500

AT15move Standard Lengths (mm)

670563006705

6000

750070955595

5295

5760

In-between lengths available from 1,400 to 30,500mm

4245

Pitch/LengthVersion

Numberof Teeth

AT15 MOV / 1500 BFXAT15 MOV / 1590 BFXAT15 MOV / 1710 BFXAT15 MOV / 1800 BFXAT15 MOV / 1905 BFXAT15 MOV / 1995 BFXAT15 MOV / 2250 BFXAT15 MOV / 2505 BFXAT15 MOV / 2790 BFX

100106114120127133150167186

Pitch/LengthVersion

Numberof Teeth

AT15 MOV / 3000 BFXAT15 MOV / 3285 BFXAT15 MOV / 3495 BFXAT15 MOV / 3750 BFXAT15 MOV / 4005 BFXAT15 MOV / 4245 BFXAT15 MOV / 4500 BFXAT15 MOV / 4740 BFXAT15 MOV / 4995 BFX

200219233250267283300316333

Pitch/LengthVersion

Numberof Teeth

353373384400420447473500

AT15move AT15move AT15move

AT15 MOV / 5295 BFXAT15 MOV / 5595 BFXAT15 MOV / 5760 BFXAT15 MOV / 6000 BFXAT15 MOV / 6300 BFXAT15 MOV / 6705 BFXAT15 MOV / 7095 BFXAT15 MOV / 7500 BFX

Standard Lengths

11

move-series®


AT15move - M Tooth Shear Strength (specific belt tooth load bearing)

R.P.M.n [min ]

R.P.M.n [min ]

FUSPEC[N/cm]

FUSPEC[N/cm]

020406080

100200300400500600700

200022002400260028003000320034003600380040004500

168.0165.2162.7160.3157.9155.8146.5139.0132.8127.4122.6118.4

85.382.079.076.273.671.168.866.664.662.660.756.4


R.P.M.n [min ]

R.P.M.n [min ]

FUSPEC[N/cm]

FUSPEC[N/cm]

8009001000110012001300140015001600170018001900

5000550060006500

114.6111.1107.9105.0102.299.797.395.092.990.888.987.1

52.549.045.842.8


R.P.M.n [min ]

R.P.M.n [min ]

FUSPEC[N/cm]

M SPEC[Ncm/cm]

PSPEC[W/cm]

FUSPEC[N/cm]

M SPEC[Ncm/cm]

PSPEC[W/cm]

020406080

100200300400500600700800900

1000110012001300140015001600170018001900

2000220024002600280030003200340036003800400045005000550060006500

168.0165.2162.6160.2157.9155.8146.5139.0132.8127.4122.6118.4114.6111.1107.9105.0102.299.797.395.092.990.888.987.1

40.139.438.838.237.737.235.033.231.730.429.328.227.326.525.725.024.423.823.222.722.121.721.220.8

0.0000.8271.6272.4053.1613.8987.33210.43713.28815.93518.41120.73922.93925.02427.00728.89730.70132.42734.08035.66537.18738.64940.05541.407

85.382.079.076.273.671.168.866.664.662.660.756.452.549.045.842.8

20.319.618.818.217.516.916.415.915.414.914.513.412.511.710.910.2

42.70945.17147.45849.58451.56153.39955.10956.69758.17159.53860.80263.54765.75167.46868.74369.611



50 AT10 MOV / 3750 BFX

Construction

Open-Ended“M”


32 50 75 10025



Specific Stiffness

Belt Mass

7,395 9,135 14,790 22,185 29,580

1.85 - 106 2.28 - 106 3.70 - 106 5.55 - 106 7.40 - 10 6

Dimension

F [N]zul

C [N]spec

[kg/m/cm]

Construction

Open-Ended“M”


50 75 100 150



Specific Stiffness

Belt Mass

18,200 27,300 36,400 54,600

4.55 - 106 6.82 - 106 9.10 - 106 13.65 - 106


Dimension

F [N]zul

C [N]spec

[kg/m/cm]

Construction





Belt Mass

6,750 8,625 13,470 20,200 26,940

Dimension

[kg/m/cm]

F [N]zul




Belt Mass

Dimension

F [N]zul

[kg/m/cm]


0.173 0.222 0.347 0.520 0.693

0.175 0.221 0.351 0.526 0.701

32 50 75 10025

8,450 11,050 17,550 26,000 35,100

0.237 0.303 0.473 0.710 0.946

12 move-series®

222 Industrial Way West Eatontown, NJ 07724

Tel: 732-460-9500 Fax: 732-542-6725

www.brecoflex.com e-mail: [email protected]

Contact U s

Copyright 2019 BRECOflex CO., L.L.C. • BRECO®, BRECOFLEX® & ATN® are registered trademarks of BRECO Antriebstechnik GmbH • ARC-POWER® is a registered trademark of BRECOflex CO., L.L.C. • Kevlar® is a registered trademark of DuPont Patents Pending • ESBAND® is a registered trademark of Max Schlatterer GmbH & Co. KH Patents Pending. Specifications are subject to change without prior notice.

All recommendations for the use of the products described herein and all other data or information set forth in this publication, whether concerning such products or otherwise, are furnished without any guarantee, warranty representations or inducement of any kind whether expressed or implied, including but not limited to warranties of merchantability and fitness for a particular purpose. BRECOflex CO., L.L.C. expressly disclaims liability under any theory, including without limitation, contract negligence, misrepresentation or breach of any obligation relating to the recommendation, data or information set forth herein. Readers and customers are encouraged to conduct their own test before using any product. Read its label and all related instructions. BRECOflex CO., L.L.C. reserves the right to make changes in the technical and dimensional specifications of its products without prior notice. Responsibility for expenses incurred as a result of product changes or discontinuance of a product lies solely with the purchaser.

Prin

ted:

09/

19Regional Sales Offices:Atlanta (770) 317-8745 Dallas (214) 476-5650 Miami (770) 317-8745 Richmond (804) 387-5760Bay Area (661) 713-0121 Denver (303) 470-7226 Milwaukee (908) 461-6995 Seattle (503) 781-3631 Baltimore (804) 387-5760 Detroit (908) 433-0036 Minneapolis (908) 461-6973 Salt Lake City (303) 470-7226Boston (603) 496-5833 Ft. Wayne (908) 461-1168 Nashville (732) 757-6647 San Antonio (214) 476-5650 Buffalo (412) 600-5632 Grand Rapids (908) 461-1168 New York (732) 829-7773 Toledo (908) 433-0036Charlotte (908) 461-3937 Houston (214) 476-5650 Philadelphia (732) 829-7773 Toronto (416) 476-7107Chicago (908) 461-6995 Indianapolis (908) 461-2344 Phoenix (480) 961-3846 Mexico City +52 1 55 45335835Cincinnati (908) 461-2344 Las Vegas (480) 961-3846 Portland (503) 781-3631 Monterrey +52 1 55 40840778Cleveland (412) 600-5632 Los Angeles (661) 713-0121 Pittsburgh (412) 600-5632 Guadalajara +52 1 55 40949053

SO 9001 CERTIFIED COMPANY

Date post:	03-Apr-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

move-series - BRECOflex Co. · 2019-10-25 · 3 move-series® Advantages 3D Model Standard...

Documents