Can be mounted “right-at-hand,” yet folds completely out of the way when not in use. The small crank has a 100 mm radius and is intended for lifting light to medium weight loads. The large crank has a 130 mm radius and is designed to lift larger loads with less effort. ■ Movotec ® Drives > Folding Hand Cranks (small and large) Technical Data • Materials: nylon handle with spring-loaded steel locking mechanism • Operating temperature range: 0º F (-18º C) to 115º F (46º C) Product Note Large folding cranks are also available in a corrosion-resistant version for application in environments subjected to periodic wash-down. Please contact your SUSPA sales representative for additional information. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Small Crank Large Crank
Transcript
Can be mounted “right-at-hand,” yet folds completely out of the way when not in use. The small crank hasa 100 mm radius and is intended for lifting light to medium weight loads. The large crank has a 130 mmradius and is designed to lift larger loads with less effort.
■ Movotec® Drives > Folding Hand Cranks (small and large)
Technical Data• Materials: nylon handle with spring-loaded
steel locking mechanism
• Operating temperature range: 0º F (-18º C) to 115º F (46º C)
Product NoteLarge folding cranks are also available in a corrosion-resistant version for applicationin environments subjected to periodic wash-down. Please contact your SUSPA salesrepresentative for additional information.
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
Operating Instructions for the Folding Hand CrankThe hand crank can be folded back andaway from the user to nearly disappearunder the top of the work surface.
Top View Front View
Hand crank in operational position
Hand crank must be pulled to a stop in the direction of its axis
Hand crank can then be folded under the worksurface top
Folding Hand CranksDimension Chart: Standard
Description Model Number A B C
(mm) (mm) (mm)
Small Crank FC 138 100 170
Large Crank FC1 142 130 200
Ø 10
5 (PIN PLACEMENT)
6292
169
CCLEARANCE FORFOLDING RADIUS
BA
29.8
max. 65mm
TABLE TOP SURFACE
TABLE FRONT EDGE
TABLE TOP SURFACE
TABLE FRONT EDGE
TABLE TOP SURFACE
TABLE FRONT EDGE
! Spec Sheets 5/4/00 5:29 PM Page 4
Providing push-button convenience, the new and improved Movotec motor drives are lighter, smaller, faster-operating, and carry the CE recognition mark. The new modular design is easy to install, and consistsof a motor drive, transformer, and activation switch. Its safety features — including a low-voltage isolationtransformer and thermal and current limits — protect against overheating and overload conditions.
■ Movotec® Drives > Motor Drive Unit
Technical Data• Material (motor and transformer): welded
sheet metal enclosure (painted)
• Material (activation switch): plastic
• Input voltage: 110 VAC, 240 VAC
• Input current: 1.6 amps, 0.8 amps
• Transformer voltage (secondary): 22 VAC
• Transformer current (secondary): 8 amps
• Switch voltage: 5 VDC
• Switch current: 25 milliamps
• Duty cycle: 10% (intermittent)
• Operating temperature range: 0º F (-18º C) to 115º F (46º C)
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
A
B
C
D
E
A. Pump/Motor Unit, B. Mounted Switch, C. 110 VAC Transformer, D. Hand Held Switch, E. 240 VAC Transformer
Motor Drive Unit - TB (North America) M1S-TB for use w/ small pumpsMotor Drive Unit - PB (North America) M1S-PB for use w/ large pumpsMotor Drive Unit - TB (Europe) M2R-TB for use w/ small pumpsMotor Drive Unit - PB (Europe) M2R-PB for use w/ large pumps
Dimension ChartThe “C” dimension depicted on this drawing varies depending on the size of the pump utilized in your lift system (longer adjustment ranges requirelonger pumps). Use the following chart to determine the actual dimension.
• Operating temperature range: 0º F (-18º C) to 115º F (46º C)
• Maximum drive speed: 110 rpm
• System operating parameters (maximum load ratings and actual adjustment ranges)are determined by specific pump and cylinder combinations. Please see the SystemSpecification Guide (pg. 8) for detailed operating data and ordering information.
Product NoteLarge pumps are also available in a corrosion-resistant version for application in environments subjected to periodic wash-down. Please contact your SUSPA salesrepresentative for additional information.
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
Small Pump (TB) and Large Pump (PB)Model Number and Dimension ChartThe “A” and “B” dimensions depicted on this drawing vary depending on the size the pump utilized in your lift system (longer adjustment ranges requirelonger pumps). Use the following chart to determine the actual dimension.
To determine which pump is required for your lift system, please refer to the System Specification Guide on page 8.
Small Pump Large Pump
! Spec Sheets 5/4/00 5:30 PM Page 8
The dual drive is the activation mechanism for 8 cylinder lift systems. This unit must be used in conjunctionwith “heavy-duty” CB cylinders only. The dual drive is a combination drive/pump unit, and is only offered in a motorized configuration.
■ Movotec® Pumps > Dual Drive
Technical Data• Material: welded sheet metal enclosure
(painted)
• 904 kg (2,000 U.S. lbs.) load capacity (maximum)
• Operating temperature range: 0º F (-18º C) to 115º F (46º C)
• Maximum drive speed: 60 rpm
• System operating parameters (maximum load ratings and actual adjustment ranges)are determined by specific pump and cylinder combinations. Please see the SystemSpecification Guide (pg. 8) for detailed operating data and ordering information.
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
Dual DriveModel Number and Dimension ChartThe “W” dimension depicted on this drawing varies depending on the size of the pump utilized in your lift system (longer adjustment ranges requirelonger pumps). Use the following chart to determine the actual dimension.
Model Number W
(mm)
PB4615 0PB4631 175
To determine which pump is required for your lift system, please refer to the System Specification Guide on page 8.
770800
15
W
Ø 6.5MOUNTINGHOLES (4X)
290310
10
16
135
! Spec Sheets 5/4/00 5:30 PM Page 10
Compression Nuts / Ferrules
Constructed of brass, these components ensure a “time-tested” seal. Two ferrules and compression nuts (each)are required for each cylinder in your application. Like the majority of our customers, let our production specialists assemble your system for you.
• Require a torque of 89 inch-pounds for a proper seal
Tubing
Flexible yet durable, Movotec tubing makes installation of your lift system simple and easy, whether you’reretrofitting one table or manufacturing one thousand. Tubing can be custom-cut to desired lengths, pleasespecify when ordering.
Technical Data• Material: nylon
• O.D.: 4 mm (0.157 in.)
• Minimum bend radius: 5 cm (2 in.)
• Maximum available length: 500 cm (16 ft.)
• Minimum available length: 40 cm (16 in.)
• Maximum ratio: 5:1 (the ratio of longest to shortest tube length cannot exceed 5:1)
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
Designed for O.E.M. applications, each cylinder utilizes a unique set of end-fitting configurations to assist inyour design and manufacturing process. These cylinders must be used in conjunction with an externalguide mechanism to prevent non-axial loading of the cylinder. The Movotec A.T.U. telescoping leg unit wasengineered to support CE cylinders.
CE cylinders have a 90º tubing port and grooved end-fittings for use with e-ring type fasteners.
CS cylinders have an in-line tubing port and grooved end-fittings for use with e-ring type fasteners.
CH cylinders have a 90º tubing port and end-fittings containing chamfered holes for use with pin- or bolt-type fasteners.
■ Movotec® Cylinders > CE, CS, and CH Cylinder
Technical Data• Materials: brass body with stainless steel rod
• Cylinders are single-acting, requiring an external force of 6.78-11.3 kg (15-25 U.S. lbs.) for retraction
• Operating temperature range: 0º F (-18º C) to 115º F (46º C)
• Maximum cylinder load = 113 kg (250 U.S. lbs.)
• System operating parameters (maximum load ratings and actual adjustment ranges)are determined by specific pump and cylinder combinations. Please see the System Specification Guide (pg. 8) for detailed operating data and ordering information.
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
CE, CS, and CH CylinderModel Number and Dimension ChartThe “A” and “L” dimensions depicted on this drawing vary depending on the size of the cylinder utilized in your lift system. Use the following chart to determine the actual dimension.
To determine which cylinder is required for your lift system, please refer to the System Specification Guide on page 8.
CE Cylinder CH Cylinder CS Cylinder
! Spec Sheets 5/4/00 5:30 PM Page 14
Designed for O.E.M. or retrofit applications, CB cylinders incorporate their own guide/support system andcan be bolted onto virtually any surface, for use as a “stand-alone” telescoping leg unit.
■ Movotec® Cylinders > CB Cylinder
Technical Data• Materials: extruded aluminum body (painted)
with nickel-plated rod
• Cylinders are single-acting, requiring an external force of 9.04-13.56 kg (20-30 U.S. lbs.) for retraction
• Operating temperature range: 0º F (-18º C) to 115º F (46º C)
• Offered in “standard” and “heavy-duty” configurations (for larger load ratings)
• Maximum “standard” cylinder load: 113 kg (250 U.S. lbs.)
• Maximum “heavy-duty” cylinder load:149.16 kg (330 U.S. lbs.)
• System operating parameters (maximum load ratings and actual adjustment ranges)are determined by specific pump and cylinder combinations. Please see the System Specification Guide (pg. 8) for detailed operating data and ordering information.
Product NoteCB cylinders are also available in a corrosion-resistant version for application in environments subjected to periodic wash-down. Please contact your SUSPA salesrepresentative for additional information.
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
CB CylinderModel Number and Dimension Chart: StandardThe “A”, “B” and “L” dimensions depicted on this drawing vary depending on the size of the cylinder utilized in your lift system. Use the following chartto determine the actual dimension.
*Heavy duty cylinders for larger loads. Please see the System Specification Guide (pg. 8) for detailed operating data.
! Spec Sheets 5/4/00 5:30 PM Page 16
With smooth telescoping movement and rigid structural integrity, our two-piece anodized aluminum extrusionwas designed to support the application of CE cylinders. Engineered to be used as a free-standing leg unit orexternal guide mechanism, the A.T.U. supports the use of many types of brackets, hardware, or other structuralcomponents. For O.E.M. applications only.
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
BOSS ACCEPTS 1/4 " HEX HEAD SCREWOR BOLT FOR CROSS BEAM MOUNTING UPPER BEARING ASSEMBLY
BOSS ACCEPTS 5/16 "–18 THREADFORMING SCREW FOR WORK SURFACEOR FOOT MOUNTING
165
181
33
195130
110.4
42.5
600
Aluminum Telescoping Uprights (A.T.U.)
Description Model Number
Movotec® guide mechanism ATU-600/300-E
! Spec Sheets 5/4/00 5:30 PM Page 18
Large and Small Mounting Brackets
Mounted to the face of the CB cylinder body, these brackets assist in the application of the cylinder. Two brackets are required for each cylinder.
Glides
The standard “foot pad” for CB cylinders. This glide is adjustable for uneven floor surfaces.
Mounting Glides
Also for supporting the CB cylinder, this glide may be used as a mountable version of our standard glide, or inverted and used as a mounting bracket when the cylinder is mounted “rod up” (upside down).
• Operating temperature range: 0° F (-18° C) to 115° F (46° C)
Product NoteGlides and mounting glides are also availablein a corrosion-resistant version for applicationin environments subjected to periodic wash-down. Please contact your SUSPA salesrepresentative for additional information.
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
Glide
Mounting Glide
SmallMountingBracketon cylinder
LargeMountingBracketon cylinder Small Mounting Bracket Large Mounting Bracket
Basic Lift System ConfigurationMovotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERSby a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotationof the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components.
Introducing SUSPA’s new electronically-controlled Linear Actuator Systems that are designed for streamlined,efficient integration into desks and table legs. The systems are a premier solution for office furniture applications,due to their compact size, lifting strength, speed, and quiet operation.
The new VERSALIFT includes an integrated motor-driven actuator/cylinder assembly, a power transformer,and a surface-mounted activation switch.
SUSPA representatives are available to assist customers in the proper application of the Linear Actuator Systems.
VERSALIFT™
Leg Actuator• Load 34.804 - 74.58 kg (77 - 165 U.S. lbs.)
maximum load per leg
• Speed 5 - 25 mm/s (.2 - 1 in/s)
• Stroke 150 - 420 mm (6 - 17 in.)
• Compact design
• Original equipment manufacturer
• Planetary gearbox
• Fully synchronized even in unbalanced loading conditions
Control Box• 100/110/240 VAC• 50 Hz input power capability• Controls up to six legs simultaneously• Mounts with four screws
6 mm Spindle Pitch: DO NOT EXCEED 90.4 kg (200 U.S. lbs.)
! Spec Sheets 5/4/00 5:30 PM Page 24
Before Movotec
Convenient, easy-to-install bolt-on ergonomic lift systems adjust work-station height to each person ortask. They can be installed quickly – with just a few common tools – on tables, benches, desks, platforms,conveyors, etc.
Attach the pump, route the flexible tubing, and bolt on the cylinders. Whether motorized or crank driven, youcan transform your current workbench, platform or other structure into a height-adjustable workstation.
Movotec “Quick-Ship” Lift Systems are available in five different adjustable ranges, and are capable of liftingloads of up to 452 kg (1,000 U.S. lbs.). Level elevation is achieved even when the system is subjected to unbalanced loading conditions.
Movotec® “Quick-Ship” Lift Systems
Each Movotec “Quick-Ship” system isshipped within 3-5 working days, comescompletely assembled, and includes:
• Motorized switch and power supply available, or pump unit driven by our unique “fold-away” hand crank
• Two 8 ft. sections of flexible tubing
• Two 10 ft. sections of flexible tubing
• Four lift cylinders
• Four glides
• Ten tubing clips (adhesive backed) and cable ties
• A “tube shortening” kit
After Movotec
Crank Driven Lift System
Motor Driven Lift System
A D
E
B
C
A. 110 VAC Transformer, B. Mounted Switch, C. 240 VAC Transformer, D. Hand Held Switch, E. Tubing Clips and Cable Ties
! Spec Sheets 5/4/00 5:30 PM Page 29
Quick-Ship Systems / Manual
Specification Chart and DimensionsThe “A”, “B”, “L”, “X” and “Y” dimensions depicted on the drawings vary depending on the size of the cylinder utilized in your lift system. Use the following chart to determine the actual dimension. See the back page for folding hand crank positions.
Adjustment Lift Model Number Range Capacity A B L X Y
CB Cylinder with Glide (for manual and motorized applications) Pump with Small Crank
0.452 kg = 1 U.S. lb. / 25.4 mm = 1 in.
! Spec Sheets 5/4/00 5:30 PM Page 30
7.5
12 TYP
69 TYP
45 TYP
130
200219
48 9.5
79.56 (2X)
181
PB – 40PB – 54
CO
F P
UM
P
TRANSFORMERJACK
ACTIVATIONSWITCH JACK
Ø 6MOUNTINGHOLE (2X)
R 6MOUNTINGHOLE (2X)
C
PB PROFILE
PB PROFILETB PROFILE
TB PROFILE
Ø 6MOUNTING
HOLE
LAR
GE
PU
MP
PR
OF
ILE
LAR
GE
PU
MP
PR
OF
ILE
SM
ALL
PU
MP
PR
OF
ILE
SM
ALL
PU
MP
PR
OF
ILE
Ø 4.7(2X)
CABLE(BLACK-3M LONG)
25.4 TYP
Ø 13.4
9.5
50.8
59
88.998.4
38.1
76.2
57.5 TYP
82
90TYP
99.8TYP
10.5(4X)
7.5(4X)
CABLE(2 METERS)
CABLE(0.5 METERS)70
Ø 4.3MOUNTINGHOLE (4X)
6858
PLUG(NEMA 5-15P)
CABLE(2 METERS)
EUROPLUG(CEE 7/16)
Motor Cable and Motor Cable Plug Motor Drive Unit
Quick-Ship Systems / Motorized
Specification Chart and DimensionsThe “A”, “B”, “L”, and “C” dimensions depicted on the drawings vary depending on the size of the cylinder utilized in your lift system. Use the following chart to determine the actual dimension.
Adjustment Lift Model Number Range Capacity A B L C
