MRLMini Mac

400THERMOPLASTIC DETAIL STRIPER

The Mini Mac 400 is an agile,

compact design perfect for

increasing your productivity for

intersection and lane markings.

MECHANICAL FEATURES

• Powered by 25 hp LPFueled Engine

• Adjustable Width RibbonExtrusion Die

• Easy Fill 400 lb / 181 kg Capacity MaterialTank with Integral Material Pump

• 100 lb / 45 kg Dual Drop GlassBead Application System

• Electronic Skip-Line System Available

• Right Side or Left SideApplication Units Available

5379 SOUTHGATE DR. BILLINGS, MT 59101 1-877-788-2907

ENGINE2 Cylinder 25 hp Kohler Command Series• Air Cooled - Electric Start - LP Gas Fueled - Engine Hour Meter - Easy Access - Low-Emission HYDRAULIC SYSTEM• Hydraulic Propulsion• Dual Front Drive Motors• Infinitely Variable Speed Control• Speed 0-8 mph / 0-12.8 kph• One Peddle Forward / Reverse• Dynamic Braking• Hydraulic Material Pump Drive• Hydraulic Cooler Assembly MATERIAL MARKING SYSTEM• 400 lb / 180 kg Capacity Oil Jacketed Material Tank• Variable Speed Material Pump Integral to Material Tank• LP Fired Oil Heating System Integral to Tank• Oil Circulation Pump• Easy Access Material Tank Lid for Filling• Electronic Material Pump Speed Control Enables Automatic Increase or Decrease of Material Volume as Demand Requires• Pump Speed RPM Digital Display• 100 lb / 45 kg Capacity Non-Pressurized Glass Bead Hopper• Single Drop Glass Bead System with 3 Air Assist glass Bead Dispensers • Optional: Double Drop Glass Bead System with 6 Dispensers MATERIAL RIBBON EXTRUSION DIE SYSTEM• Standard: 13 inches / 33 cm Width• Manual Slide Bars: 4 inches / 10 cm - 6 inches / 15 cm - 8 inches / 20 cm - 10 inches / 25 cm - 12 inches / 30 cm• Optional Extrusion Systems: • 0-18 inches / 45 cm Widths Adjustable with Slide Bars • 0-20 inches / 50 cm Widths Adjustable with Slide Bars • Automatic Width Adjustable Die (no slide bars): 4 inch / 10 cm - 6 inch / 15 cm - 8 inch / 20 cm - 12 inch / 30 cm - or Double 4 inch / 10 cm lines with 4 inch / 10 cm spacing • 18 inch Double Die with 6 inch / 15 cm and 12 inch / 30 cm openings - Widths Adjustable with Slide Bars AIR SYSTEM• 8 cfm / 226 l/min @ 110 PSI / 7.5 bar Air Compressor• Air Purge System for Material Lines and Ribbon Extrusion Die• Air Lift Control for Steel Front Guide Bar

AIR SYSTEM (continued)• Air Assist for Glass Bead Dispensers• Air Lift Control for Extrusion Die and Bead Gun Articulating Steel Mount with Steel Locking Pin• Air Operated Extrusion Die Actuation Solenoids• Moisture Separator and Unloader ELECTRONICS• Ribbon Extrusion Die On / Off Switches• Test Switches• Optional: Skip-Line MST-14 System • Electronic Skip-Line System with Metric or English Functions • Electronic Speedometer • Electronic Footage Counters • Remote Manual Push Button On / Off Extrusion Die Control • E-Stop Emergency Shut Down• Digital Oil Temperature and Pilot Light Controls• Electronic Pump Speed Controls with RPM Display• 3 LED Night Lights to Illuminate Material Tank, Gun Cart and Work Area• Rear LED Amber Strobe Light• Post Mounted Amber Strobe Light• Optional: Laser Guidance Device OTHER STANDARD FEATURES:• Parking Brake• Docking Hook with Quick Release • 40 lb / 18 kg Capacity LP Tank• Colors: Signal Yellow, Safety White, Traffic Orange, Lime Squeeze Green• Fire Extinguisher• Operators Manual Optional Equipment:• Transport Trailer• Left Hand Drive• On-Site Training DIMENSIONS• Weight: Approx. 1,700-1,930 lbs / 727-877 kg (depending on equipment)• Width: 60-70 inches / 152-178 cm (depending on application die used)• Length: 90 inches / 229 cm • Height: 80 inches / 203 cm (top of the beacon)• Turning Radius: 3.5 ft / 1.06 m Approximate Shipping Crate Size:

96 inches long x 80 inches high x 68 inches wide

244 cm long x 203 cm high x 172 cm wide

A L L S P E C I F I C A T I O N S S U B J E C T T O C H A N G E .

MRL Mini Mac 400 T E C H N I C A L S P E C I F I C AT I O N S

Easy Fill Thermoplastic Material Tank

Operator Control Console

Highly Maneuverable Design

Custom Transport Trailer