media:scape Lounge - Canopy and Ledge
August 2014 Page 1 of 12
Ledge Canopy
PROTECTIVEBLANKETS
1/2"SOCKET
PROTECTIVEGLOVES
5mm HEX
CAUTION : Install the necessary counterweight plates as per pages 2 & 3. Failure to follow these instructions could result in the lounge tipping over and causing personal injuries.
media:scape Lounge - Canopy and Ledge
August 2014 Page 2 of 12
CENTER UNIT LH or RH END UNIT
CANOPY
LEDGE
TWO (2) NOCOUNTERWEIGHT
PLATES REQUIRED
FOURTEEN (14) TWELVE (12)
PLATES REQUIREDCOUNTERWEIGHT
COUNTERWEIGHTPLATES REQUIRED
TWO (2)
FOURTEEN (14)
PLATES REQUIREDCOUNTERWEIGHT
COUNTERWEIGHTPLATES REQUIREDPLATES REQUIRED
COUNTERWEIGHT
1 2
3
4
COUNTERWEIGHT
RIVET
HOLE TOACCOMODATE RIVET
FOOT
VELCRO
media:scape Lounge - Canopy and Ledge
August 2014 Page 3 of 12
Installing Two (2) Counterweights for Canopy
Installing Twelve (12) or Fourteen (14) Counterweights for Ledge
COUNTERWEIGHT SCREW
COUNTERWEIGHTBRACKET
LEFT
COUNTERWEIGHTBRACKET
RIGHT
COUNTERWEIGHT
COUNTERWEIGHTBRACKET
LEFT
COUNTERWEIGHTBRACKET
RIGHT
5
6
a
a
b
b
c
c
media:scape Lounge - Canopy and Ledge
August 2014 Page 4 of 12
TUBE SP
1/2" GAP
ACER
5/16-18 X 3"WASHER HEX BOLT
1" LONG SPACER
Ledge 1"
ADJUSTMENT BOLT1-1/8" LONG
ADJUSTMENT BOLTFLUSH WITH SIDEOF PANEL
INSTALL
1 2
3
Ledge
NOTE : This installation requires two (2) installers.
SIDE VIEW
SIDE VIEW
a
b
media:scape Lounge - Canopy and Ledge
August 2014 Page 5 of 12
5/16-18 X 3"WASHER HEX BOLT
5mm HEX BITOR ALLENWRENCH
LEDGE BACK PANELSNAP
SNAP
4
5
b
a
media:scape Lounge - Canopy and Ledge
August 2014 Page 6 of 12
LEDGEWORKSURFACE
(OPTIONAL)
3/8 EURO SCREW
a
b
Ledge Worksurface (Optional)
NOTE : Do not over-tighten euro screws.
media:scape Lounge - Canopy and Ledge
August 2014 Page 7 of 12
Canopy
NOTE : This installation requires two (2) installers.
ADJUSTMENT BOLTFLUSH WITH SIDEOF PANEL
INSTALL
ADJUSTMENT BOLT1-5/8" LONG
1
2
3
TUBESPACER
1/2" GAP
5/16-18 X 3"WASHER HEX BOLT
1-9/16" LONG SPACER
Canopy1-9/16"
SIDE VIEW
SIDE VIEW
a
b
media:scape Lounge - Canopy and Ledge
August 2014 Page 8 of 12
5/16-18 X 3"WASHER HEX BOLT
4
a
b
5mm HEX BITOR ALLENWRENCH
SIDE VIEWALIGNALIGN
CANOPIES INLINEWITH EACH OTHER
CANOPIES FACE TO FACE-WITH EACH OTHER
media:scape Lounge - Canopy and Ledge
August 2014 Page 9 of 12
CANOPY BACK PANEL
SNAP
SNAP
5
media:scape Lounge - Canopy and Ledge
August 2014 Page 10 of 12
1"
Removal of Ledge or Canopy Back Panel
NOTE : This removal requires two (2) installers.
1
2
media:scape Lounge - Canopy and Ledge
August 2014 Page 11 of 12
HOLEPUNCHTOOL
TEMPLATE
TEMPLATECENTERINGFEATURE
23-7/8"
23-7/8" OR
EXAMPLE
1
2
5
6
4
Modification to an existing lounge
NOTE : You will need to cut the holes in the fabric. We recommend a hole punch tool that is 1” diameter.(McMaster -Carr, Osborne, etc.)
PIN
3
media:scape Lounge - Canopy and Ledge
August 2014 Page 12 of 12
If the existing lounge DOES NOT have a threaded insert in the oblong hole location
NOTE : You will need to purchase a 7/16” diameterdrill bit & a 5/16 hex bit or allen wrench
OBROUND HOLE SHOULD LOOK LIKE THIS
WHEN COMPLETED
DEPENDING ON THECUTTING METHOD,
BOTH ARE ACCEPTABLE
OR
TEMPLATE
TEMPLATE
5/16 HEX BITOR ALLENWRENCH
1
2 2 2
3 3 3
