Multipurpose Hall Building A - Procurement Notices

AMultipurpose Hall Building

Unit Rate Total

$ Amount $

(A) M.P.H Building

Construction Works :

Bill No. (1) Excavation & Earth Works

1 Demolish the existing external steps close to the existing ramp & remove safely all

the debris from the site to approved places. The price shall include the repair and

reinstatement of the existing situation to its original condition as per drawings and

the engineer's instructions.

L.S 1

2 Excavation for foundations from natural ground level up to the required designed

level. The works including:

‐ The compaction of the soil surfaces to get (98% MDD).

‐ The excavated material should be removed out from the site to the approved

places.

‐ All to be executed as per specifications, drawings and the engineer’s instructions.

M3 600

3 Supply, fill by using approved material (clean sand) around the foundations &

inside the building up to the required levels, which shall be spread in layers not

exceeding 25cm each one & compacted (98%) to reach up the required levels

(under floor slab), according to the specifications & the engineer's instructionsM3 1100

Total of Bill No. (1)

Item

Description

Unit Qty.

Contractor Signature Stamp


Unit Rate Total

$ Amount $Item

Description

Unit Qty.

Bill No. (2) Concrete & Block Works

A‐ Concrete Works

Rates of Concrete Works shall include: ‐

‐ All form works and shuttering in any form, shape and size. Making chamfered and

curved edges, allowing for and making grooves and sleeves and the like; removal of

forms and cleaning of all exposed tie wires and rods; making good the harmed

surfaces and edges and all surface finishing.

‐ Supplying, Casting, vibrating and curing as per specifications.

‐ Approved additives and admixtures.

‐ Incurred costs on Concrete Mix Designs, Sample taking, testing and providing test

results certificates, storing and saving of samples.

‐ Supplying reinforcement of any grade, size and length as detailed in the

drawings, storing on site including cutting, bending and fixing in position and

providing all tying wires, spacers, shop drawings, testing and bar bending schedules

‐ Painting of exposed surfaces of underground reinforced concrete elements with

primer and two coats of hot bituminous paint (75/25), the strokes of each layer to

be opposite to each other.

‐ Underground concrete elements prices are including expansion joints, flexcell

sheets 18mm thick & mastic.

‐ Steel bars used for alignment and fixing of reinforcement works, and extra steel

added to assure proper detailing and safety.

‐Supply & spread polythene sheets gauge 500 under the foundations & ground

slabs.

‐ Measurement of Concrete elements shall be the net dimensions as detailed in the

drawings. All recesses openings and voids shall be deducted.

‐ Measurement shall be only for the seen surfaces of elements. Overlapping and

measuring items twice under separate headings shall not be allowed.

‐ Columns are to be measured from the top level of the slab to the bottom level of

the beam or dropped beam.

‐ The concrete surface must be finished with mechanical steel trowel machine.

All works must be done as per drawings, specifications & the engineer's

instructions.

2.1 Supply & cast plain concrete B150 under the foundations m3 20

2.2 Supply & cast ready mix concrete B300 for reinforced concrete foundationsm3 200

2.3 Supply & cast ready mix concrete B300 for columns necks as shown on the

drawings, specifications and the engineer's instructions. m3 4

2.4 Supply & cast ready mix concrete B300 for tie ground beams. m3 25

2.5 Supply & cast ready mix concrete B300 for external steps. m3 8



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

2.6 Supply & cast ready mix concrete B250 for ground slab 10cm thick with steel mesh

T8/20cm each way.m2 300

2.7 Ditto, but with the steps inside the M.P.H. including steel stirrups T8/20cm & T8 for

steps nose (see DWG. S03). m3 80

2.8 Supply & cast ready mix concrete B300 for columns as shown on the drawings,

specifications and the engineer's instructions. m3 60

2.9 Ditto but for concrete walls (see DWG. S02 &S03).m3 50

2.10 Ditto but (200kg/cm2) for stop columns at roof. m3 7

2.11 Supply & cast ready mix concrete B300 for suspended hollow block slabs 25cm

thick, including the hollow cement blocks, reinforced concrete hidden, inverted &

drop beams & all the required materials.

Girders (F) are not included in this item.m2 680

2.12 Ditto, but for suspended hollow block slabs 20cm thick, including the hollow

cement blocks, reinforced concrete hidden, inverted & drop beams & all the

required materials.

m2 165

2.13 Supply & cast ready mix concrete B300 for Girders (F) at the suspended hollow

block slabs 25cm thick, including the steel reinforcement & all the required

materialsm3 100

2.14 Supply & cast ready mix concrete B300 for staircases flights & landings including all

required materials m3 15

2.15 Supply & cast ready mix concrete B250 for doors & windows lintels, sills & canopies

including all the required materials.m3 18

2.16 Ditto, but for parapet walls coping & external concrete elements.m3 5

2.17 Supply & cast 10 cm thick ready mix concrete B300 for staircase concrete parapet

walls (see DWG. S12).m3 3

2.18 Supply & cast ready mix concrete B250 for decorative concrete facade as shown on

the drawings, specifications and the engineer's instructions. m3 3

B‐ Block Works: ‐

The items include supplying hollow cement block from good and approved factory

2.19

Supply & build hollow block walling 35cm thick, consists of external block 20cm,

internal block 10 cm and 5 cm thick Polystyrene, the price includes the supplying of

all the required materials.m2 360

2.20Supply & build hollow block walling 20cm thick including the supplying of all

materials (block size 20 x 20 x 40cm). m2 390

2.21Supply & build hollow block walling 10cm thick including the supplying of all

materials (block size 10 x 20 x 40cm). m2 250




Unit Rate Total

$ Amount $Item

Description

Unit Qty.

Bill No. (3) Finishing Works

_ The price shall include the supply of all materials, galvanized angles, and

galvanized mesh not less than 50cm width, mixing, scaffolding, curing, site

cleaning, equipment and workmanship required to complete the job according to

the specifications, conditions of contract, drawings & engineer’s approval.

_The rates of the following items shall be completed in accordance with the

drawings; specs, details and as directed by the engineer.

_The contractor must submit the shop drawings to the engineer's approval before

starting the work. _Black basalt chips of size 4mm shall

be used in the precast terrazzo items.

_ Grade (A) local marble (free from cracks, holes & pits, homogeneous in color and

approved by the engineer must be used.

_ All Tiling works must be filled & polished according to the engineer's instructions.

_ All materials used for painting shall be of high quality materials based on the

British standards and must be approved by the engineer, paints and applying

method must be as per the manufacturer’s instructions.

3.1 Supply & execute internal plastering 13mm thick to walls,cielings, soffits & columns

including galvanized metal lath angles for columns, edges & chicken wire at the

intersection of concrete & block works, pipes & cement rendering as per the

engineer's instructions.

M2 1300

3.2 Ditto, but for external plastering 15mm thick to walls and soffits the price including

additional layer of 5mm thick lime free mortar (mix 1: 3) as per specs, drawings

and the engineer’s instructions.M2 150

3.3 Supply and install west bank smooth stone 5.0 cm thick with backing filling 10.0cm(Grade B-200) with steel mesh 6mm dia @ 20cmm as per the engineer's instructions. M2 90

3.4 Ditto but 5.0 cm thick with backing filling 5.0cm.M2 140

3.5 Ditto but Molatash 5.0 cm thick with backing filling 5.0cm.M2 770



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

3.6 Supply and install terrazzo floor tiles (grade A) size 25x25x2.5cm with marble chips

laid on 2cm mortar bed and 5 cm thick sand bed and terrazzo skirting 30cmx

7cmx1cm including all materials and testing as per specifications, drawings, and the

engineer's instructions.M2 240

3.7 Supply and install local marble (grade A) size 35 cm wide x 3cm thick for windows

sills laid on 2 cm thick mortar bed as per specifications, drawings, and the

engineer's instructions.RM 25

3.8 Ditto but size 36 cm wide x 3cm thick for roof parapet. RM 125

3.9 Ditto but size 76 x66 x 3cm thick for roof stop columnM2 8

3.10 Ditto but threshold size 23 cm wide x 3cm thick for doors.RM 25

3.11 Supply and install Rosabita marble size 19 cm wide x2cm thick for staircase parapet

laid on 2 cm thick mortar bed as per specifications, drawings, and the engineer's

instructions.RM 125

3.12 Supply and lay Rosabita marble stair treads size 36 cm wide x 3cm thick chamfered

once, rebated once and laid on 2cm thick mortar bed and the price includes

Rosabita marble stair risers size 12.0cm or 12.5 high x2cm thick and skirting

7/20cm high x2cm thick as per specs, drawings and the engineer ‘s instructions.RM 165

3.13 Supply and install Rosabita marble (grade A) size 30x60x2cm thick for staircase

landings & stage floor laid on 2 cm thick white cement mortar bed as per specs,

drawings, and the engineer's instructions.M2 50

3.14 Ditto but, Rosabita marble (grade A) size 30x60x2cm thick for entrance walls laid

on 2 cm thick white cement mortar bed as per specs, drawings, and the engineer's

instructions.M2 50

3.15 Supply and install colored none slipping ceramic (grade A) 8mm thick for floor.M2 20

3.16 Supply and install colored glazed wall tiles (grade A) 6mm thick laid on 2cm mortar

(1:3). M2 90

3.17 Supply and install high quality moquette 6 mm thick, 1.8kg/m2 (Super lugo or

equivalent), upper Aluminum angles for upper steps edges 30*30*1.25mm,

stainless steel rod 14mm for lower edge, skirting, sticking materials, cleaning and

preparation the surface to install the moquette according to specifications and

engineer instructions

M2 570

3.18 Supply and paint, plaster with one coat of bondrol primer and at least two coat of

External quality of colored emulsion paint (Supercryle) or equal approved as per

specifications, drawings and the engineer's instructions. M2 200

3.19 Supply and paint the internal walls up to a high of 2.2m above finishing floor level

two coats of putty, one undercoat primer and two coats of colored oil paint as per

specifications, drawings and the engineer's instructions. M2 950

3.20 Supply and paint one primer and minimum two coats of emulsion paint (Poliside)

for internal walls, ceiling and drop beams as per specifications, drawings & the

engineer's instructions.M2 200

3.21 Supply and install fire rated gypsum board 120cm width and 12mm thick sheets as

per specifications, drawings, and the engineer's instructions.

The price includes the galvanized columns, beams, angles, wires, painting with

supercryle after two layers of putty, and all the needed materials to complete the

job as per the manufacturer’s requirements. M2 660



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

3.22 Supply and install gypsum tiles 60x60x1.5cm (Armstrong) as per specifications,

drawings, and the engineer's instructions.

The price includes the galv columns, beams, angles, wires and all the needed

materials to complete the job as per the manufacturer’s requirements.M2 220

3.23 Supply and cast foam concrete with fine aggregates for roof screening of ranging thickness from 4 to 15 cm and sand angle fillets size 5cmx5cm as per specifications, drawings and the engineer's instructions . M2 680

3.24 Supply and lay one layer of plasticized bitumen roofing membrane with chipping 4 mm thick, including priming concrete surface prior to laying, dressing into rain water outlets to form water proofing seal and cover the angle fillets. The rate include verticals parts skirting as per specification and drawings.Note: Measurement will be for the horizontal projection

M2 680




Unit Rate Total

$ Amount $Item

Description

Unit Qty.

Bill No. (4) Carpentry & Joinery Works

4.1 Supply, fix and paint wooden single internal flush door type D2 size 80x220x4.5cm

according to the drawing, specifications and under supervision. No. 2

4.2 Ditto, but for type D3, overall size 70x 220x4.5cm thickNo. 4



4.5 Supply and fix 120x20mm soft wood coat hook rail smoothed, plugged and screwed

to wall at 30cm center to center including priming and sanding sealer and two

coats of varnish painting with Galvanized steel coat hook screwed to rail at 20cm

center to center as per the engineer’s instructions.RM 8

4.6 Supply and fix high quality colored foldable theatre chair fixed to floor. The color

will be selected by the engineer.

The chair base and back are fabricated from sandwich covered with mahogany and

framed with painted natural timber. The base and back have high density sponge

and durable textile.

The base size is 50x50cm and 45cm high from the floor and 105cm for the back.

The chair includes hidden arm for writing in addition to hard plastic cover for the

base and back.

All as per specs, drawings and the engineer's instructions.

No. 432




Unit Rate Total

$ Amount $Item

Description

Unit Qty.

Bill No. (5) Aluminum & Metal Works

.The rates of the following items shall be Completed in accordance with drawings,

specifications, details and as directed by the engineer.

. Door frames shall fit walls & sizes of door openings, taking into consideration the

thickness of plastering on both sides of the frames.

. Hardware for doors shall be Waley type with approved handles.

.The aluminum windows are colored powder coated aluminum Jordanian Type

7000 / 4500 or approved equivalent with sliding leaves, frame, clear glass 4mm

thick, fly screen ironmongery, and hardware and aluminum accessories.

.The aluminum will be tested in approved testing laboratory.

. The contractor has to submit shop drawings to the engineer before fabrication

and installation.

5.1 Supply & install Mul‐T‐Lock door type 417 with overall size 125cm width x 220cm

height (D1) with powder coated paint. Door lock type 235 & Mul‐T‐Lock serrated

cylinder. All to be carried out according to the specifications, drawings & the

engineer's instructions.No. 2

5.2 Ditto, but with size 105 cm widths x 220cm height (D4). No. 1

5.3 Ditto, but with size 90 cm widths x 220cm height (D6).No. 3


5.5 Supply and fix powder coated colored aluminum window type "W4" size 150 cm

width x 150 cm height, (Type 7000) sliding leaves, fly screen leaves, frame, clear

glass 4mm thick, ironmongery, and hardware and aluminum accessories. All as per

specs, drawings and the engineer’s instructions.No. 4

5.6 Ditto, but type "W5" size 150 cm width x 70cm height.No. 3

5.7 Ditto, but type "W6" size 220 cm width x 150cm height. No. 2


5.9 Supply and fix powder coated colored aluminum type 4500 for hinged window

type "W8" size 95cm width x 705cm height, unclear glass 4mm thick, ironmongery

and hardware as per specifications and drawings. No. 2

5.10 Supply and fix galvanized steel protection for internal windows overall size 240x70

cm type (W2), the prices including all the steel, the fixation accessories, painting

with one primer coat & two coats of oil paint, all according to the drawings,

specification and engineer’s instructions. No. 6

5.11 Supply and fix galvanized steel protection for external windows overall size

150x150 cm type (W4), the prices including all the steel, the fixation accessories,

painting with one primer coat & two coats of oil paint, all according to the

drawings, specification and engineer’s instructions.

No. 4

5.12 Ditto, but size 150x70 cm type (W5)No. 3



5.15 Supply and fix stainless steel handrail for stair case pipe1.5” internal dia. 2.5mm

thick fixed to walls by stainless steel plate and 4 bolts stainless steel every 1.0m

and 10cm space between wall and the pipe. All as per specs, drawings and the

engineer's instructions.RM 20



Unit Rate Total

$ Amount $Item

Description

Unit Qty.


Bill No. (6) Plumbing & Sanitary Works

6.1 Supply and fix white glazed porcelain hand wash basin size 50cm x 41cm (Vitra type

6602+6173) or approved equivalent, complete with all water supply pipes ½",

waste fitting, trap, plug and chain, chromium plated water mixer 1/2" dia. Jack

type) (From Artema‐Armix or Hamat or approved equivalent) and mirror 60x60cm,

Supply & fix white glazed soap tray tiled into block walls, steel brackets supports

and the drainage line to floor trap 2”, all needed accessories & the pipe concrete

encasement as per specifications, drawings and the engineer's instructions.

No. 6

6.2 Supply & fix white glazed porcelain squatting W.C. suite (HARSA EUROPEAN ‐ TYPE

or approved equivalent) complete with porcelain flushing cistern, pip hose, 1/2"

dia. UPVC 100 cm long flushing pip hose for toilets, seat & plastic cover, white

glazed toilet paper holder tiled into block walls (size 15cmx15cm), 4" dia. P.V.C.

drainage pipe to the nearest main drainage line, all needed accessories & the pipe

concrete encasement (as shown in the drawings (Vitra‐Normus or approved

equivalent).

No. 6

6.3 Ditto, but higher than the standard with its stainless steel handrails one is fixed and

the other one is movable where the type is Vitra for persons with special needs

(Vitra‐Normus or approved equivalent). No. 2

6.4 Supply and fix 1" dia. galvanized pipe for drop water pipe connected from existing

building roof tanks to the water line as shown on the drawings and according to

engineer's instructions, the price shall include all necessary fitting, valves

excavations , backfilling, concrete encasement & all needed materials to complete

the job.

RM 15

6.5 Ditto but HDPE dia. 3/4" dia for cold water.RM 60

6.6 Supply and install UPVC pipes 4” diameter for drainage, with sockets joint 3.2 mm

wall thickness. The work shall include the excavation, backfilling, jointing, and the

pipe concrete encasement……. etc. to complete the job as per specifications,

drawings and the engineer's instructions. RM 15

6.7 Supply and install UPVC pipes 3” diameter for rain water drainage pipe, with

sockets, pipe joints, caps, supports and all needed materials to complete the job as

per specifications, drawings and the engineer's instructions. RM 40

6.8 Supply and fix floor trap 4" diameter, complete with heavy duty brass grating &

UPVC pipe to the nearest inlet with the pipe concrete encasement as per

specifications, drawings and the engineer's instructions. No. 10

6.9 Supply and install UPVC pipes 6” diameter for drainage, with sockets joint 4.7 mm

wall thickness. The work shall include the excavation, backfilling, jointing, and the

pipe concrete encasement, bedding and compacted backfilling with clean sand …….

etc. to complete the job as per specifications, drawings and the engineer's

instructions.

Also connect the sewer networks with the existing manhole as per drawings & the


RM 20



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

6.10 Ditto but 4” diameter for vent‐pipe. RM 10

6.11 Supply and install concrete manhole of internal diameter 60cm, and (50‐90) cm

depth according to the required level, 12cm thick plain concrete for walls and base,

slab, with cast iron cover with 8 ton bearing capacity according to I.S, specifications

and drawings. The price includes the connection to the existing manhole.No. 3

6.12 ditto but 80 cm diameter with depth up to 2.2m.No. 1

6.13 Supply and install an approved water distribution galvanized steel 2mm thick

cabinets with galvanized steel doors with switch locks and hammer paint for the

distribution water network with any number of cold water & hot water outlets with

polythene pipe HDPE 16 mm distribution pipes and the connection from the main

supply drop pipe G.S.P. to the distribution cabinets, air valves, gate vales, unions,

supports and all accessories needed to complete the job, all according to the

drawings, specifications & the engineer's instructions.

No. 1




Unit Rate Total

$ Amount $Item

Description

Unit Qty.

Bill No. (7) Electrical Works

The prices of all electrical works and installed equipment and components listed

below includes:

‐ Shop drawings ‐ As built ‐ ...

‐ Execution of all needed works & install all fittings and accessories required for

operation.

‐ All materials supplied (such as wires, pipes, electrical equipment…etc.) should be

of the best quality and must be approved by the supervising engineer.

‐ The work includes maintenance period for each device according to tradition in

the field.

‐ Oversees the installation and maintenance, a specialist in the field of devices

‐ Supply, Erect & Commission the electrical equipment according to the drawings,

specifications and the engineer's instructions. Also the work shall include workman

ship and all accessories needed to complete the job.

Lighting Fixtures

7.1 Supply and install surface mounting led lighting fixture ,2x16W, 1200mm ,230V,not

less than 100 Lummen/W , daylight 6500 K complete with lamps T8, driver, and

needed accessories as per drawings, specifications and according to supervisor

engineer instructions.

The price includes wires, conduits, fittings, accessories and any other needed

materials and workmanship to complete the job as per drawings specifications and

the engineer’s instructions.(Type is GAASH or equivalent brand name).

No. 25

7.2 Supply and install ceiling mounting round led light luminaire 17w with driver ,230

V, 1800 Lm ,daylight complete with lamps and needed accessories as per drawings,

specifications and according to supervisor engineer instructions.

The price includes wires, conduits, fittings, accessories and any other needed


the engineer’s instructions. (Type is GAASH or equivalent brand name). No. 14

7.3 Supply and install spot led light recessed luminaire 30w with driver ,230 V,not less

than 90‐100 Lummen/W ,daylight complete with lamps and all needed accessories

as per drawings, specifications and according to supervisor engineer instructions.

The price includes Bindle Cables , conduits, fittings, accessories and any other

needed materials and workmanship to complete the job as per drawings

specifications and the engineer’s instructions. (Type is LIPER or equivalent brand

name). according to EU specification.

No. 46

7.4 Supply and install 60x60cm led light recessed luminaire 40w ,230 V, 3400 Lm

,daylight complete with lamps drivers and needed accessories as per drawings,

specifications and according to supervisor engineer instructions.

The price includes Bindle Cables , conduits, fittings, accessories and any other

needed materials and workmanship to complete the job as per drawings

specifications and the engineer’s instructions. (Type is GAASH or equivalent brand

name). according to EU specification.

No. 106



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

7.5 Supply & Install ceiling spot fixture 150W with halogen lamp daylight complete

with all needed Bindle Cables , conduits, fittings, accessories and any other needed


the engineer’s instructions. (Type is BRAND NAME or equivalent ). according to EU

specification.

No. 68

7.6 Supply & Install stair light fixture with LED 9W lamp, cool white ,820Lm,IP65,

complete for stairs (ST1 &ST2 &ST3) with all needed wires, conduits, fittings, and

accessories and any other needed materials and workmanship to complete the job

as per drawings specifications and the engineer’s instructions. (Type is GAASH or

equivalent brand name)

No. 51

7.7 Supply, install and operate of a surface , ceiling or wall mounted emergency

lighting fixture, 160Lm ,with 3W, LED lamp with 1HRS NI‐CD batteries including

wires 3X1.5mm2 with lamps, conduits, fittings, accessories and any other needed


the engineer’s instructions. (Type is GAASH 1838 Naama or equivalent brand

name)

No. 14

7.8 Supply, install and operate a lighting emergency (EXIT) sign surface or ceiling

mounted, LED lamp with 3Hours NI‐CD batteries including wires 3X1.5mm2 with

lamps, conduits, fittings, accessories and any other needed materials and

workmanship to complete the job as per drawings specifications and the engineer’s

instructions. (Type is GAASH or equivalent brand name)

No. 5

7.9 Supply, install and operate a preparation point ( light or data or camera ), complete

with all needed pipe , J.boxes, without wires or data cables according to the

engineer’s instructions.No. 15

7.10 Supply and Install flush single circuit, one way 220V,10A, on/off switch (bticino

matix or gewiss chorus or equivalent) complete with connection box ,supporter,

conduits, wires and all needed materials and workmanship to complete the job as

per drawings, specifications and the engineer’s instructions.No. 15

7.11 Ditto but double pole one way.No. 10

7.12 Ditto but triple pole one way.No. 10

7.13 Ditto but one pole two ways.No. 10

7.14 Ditto but double pole two ways.No. 10

7.15 Supply and Install flush single circuit, one way 220V, 10A, on/off switch (bush

button) type bticino matix or gewiss chorus or equivalent with indication lamp

complete with connection box ,supporter, conduits, wires and all needed materials

and workmanship to complete the job as per drawings, specifications and the

engineer’s instructions.

No. 4

7.16 Supply and Install single phase flush 220V,16A socket outlet type bticino matix or

gewiss chorus or equivalent with needed wires 3*2.5mm2 with conduits, fittings,

support ,accessories and any other needed materials and workmanship to

complete the job as per drawings specifications and the engineer’s instructions. No. 42

7.17 Supply and Install flush telephone socket outlet, 6 wires pin type bticino matix or

gewiss chorus or equivalent with needed cable as per drawings, specifications and

any other needed materials and workmanship to complete the job as per drawings

specifications and the engineer’s instructions.No. 5



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

7.18 Supply and Install computer data, flush socket outlet, type bticino matix or gewiss

chorus or equivalent, with UTP cables CAT6 from the rack to the socket and any

other needed materials and workmanship to complete the job as per drawings

specifications and the engineer’s instructions.No. 19

7.19 Supply, install and fix adjustable flush mounting floor box Legrand Type (24

modules) with stainless cover. The price includes conduits, j. boxes, fittings,

accessories and any other needed materials and workmanship to complete the job

as per drawings specifications and the engineer’s instructions.

NOTE: suitable for concrete foundations.

No. 3

7.20 Supply and install addressable Fire Alarm control Panel (Type is Telefire or

equivalent ), 2 loops, including power supply , all needed j‐boxes , wires, batteries

, with all the necessary materials to complete the works with as programming and

operating …. etc. according to the drawings, technical specifications and the

engineer’s instructions.No. 1

7.21 Supply and install addressable smoke detector including wiring and conduits and

any other needed materials and workmanship to complete the job as per drawings

specifications and the engineer’s instructions. No. 15

7.22 Supply and install addressable heat detector including wiring and conduits and any

other needed materials and workmanship to complete the job. No. 3

7.23 Supply and install flusher LED on + fire bell (compact unit) with conduits, fittings,

accessories and any other needed materials and workmanship to complete the job. No. 4

7.24 Supply and install button operation BREAK GLASS , with plastic cover with all the

necessary wires, conduits, accessories, and any other needed materials and

workmanship to complete the job.No. 4

7.25 Supply and install an assembly box type GEWISS No. PT48. Or equivalent. as per the

engineer’s instructions. No. 8

7.26 Supply and install extract fann 8" (Type Vents or equivalent) and all needed

accessories,louvers, Frames and any other needed materials and workmanship to

complete the job as per drawings specs and engineer’s instructions. No. 4

PUBLIC ADDRESS (SOUND) SYSTEM

Supply ,Install,Connect,and Test the Following Item Below with all requirements to

finish work complete with all accessories, all equipment items for the

loudspeaker,Amplifire, Mixer,... shall be manufactured by Behringer or Inter‐M or

equivalent. Work is to include the supply of the equipment specified installation of

,connection, wiring ,commissioning,Transportation,testing, and all other details ,the

prices including all connectors,adapters,plugs.All the requirements according to

Specifications, drawings, and Engineers instructions.

7.27 Power Amplifier as per engineer instructions with all required cables , junction

boxes conduits and all necessary accessorieand the following specifications:

Nominal max power 1000 Watt

Frquacey response 50‐1500HZ

Signal To noise ratio > 80 db

Outputs /ohms 4,8,16 ohm

Outpust / volt 50, 100v

(Type Behringer or Inter‐M or approved equivalent).

No. 1

7.28 1600‐Watt 16‐Channel Powered Mixer with Multi‐FX Processor and FBQ Feedback

Detection System , type is

(Behringer EUROPOWER PMP4000 or approved equivalent). No. 1

7.29 Ceiling loud Speaker , 8'' diameter

Rated Power 10W. ncluding all required cables (2,5 mm2) , junction boxes conduits

and, metal front protection mesh, clips for quick attachment , line transformer all

necessary accessories (Type is Bosch,Cotina or equivalent)

No. 15



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

7.30 Vocal Descktop Microphone type SHURE # SM58 as per specifications and engineer

instructions.No. 6

7.31 Wireless Vocal Microphone, with Internal Battery. (Type is SHURE or equivalent)

The item includes:

‐ Charger Base with Power Supply: 220 VAC, 50 Hz.

‐ Battery: 2 Pcs.

‐ standard base controller with stand and cables for amplifier connection with 5‐pin

DIN connector.

No. 2

7.32 supply and install Main sound system Aluminum rack with all needed suitable

dimensions, shelfs and size to install all component mentioned in sound system

items (size must be 30% increasing for future extinction No. 1

7.33 Amplifier (Mic) socket out let,complete with PVC conduits, J.boxes, wiring, and all

necessary accessories to complete the job.(Type is Philips RCT or equivalent )

Distribution Switch Boards

Supply, install & commission to complete the job for the followings, the type is

MOELLER or approved equivalent:

7.34 Supply and install main power distribution board MDB, complete with additional

30% free space for future extension according to the drawings, technical

specifications, installation instructions and the supervising engineer’s instructions.

The frame of MDB is galvanized steel sheet with 2mm thickness and antistatic

primer paint and 2 coats of final polyester paint. The size & dimensions of MDB

must be enough & suitable for assemble and maintain easily all panel components

listed below.The size of the pannel will be determined after approved the

shopdrawings from the GEDCO & Supervision engineer Contractor must submit

shop drawing before manufacturing and obtain the supervising engineer’s

approval to proceed the manufacturing. Also the shop drawing must be more

detailed with all MDB components (types, ratings, specifications …etc.) also the

shop drawing must be approved by (GEDCO).

The price include all neede wires , bus bars , accessories , ....

N.O 1

7.35 supply & install 0‐500A digital Ammeter with all neededN.O 3

7.36 supply & install 0‐500 V digital voltmeter with all needed , LTL , selector swunit 1

7.37 3‐Color indication lamps with ltl fuse set 3

7.38 400/5A Current Transformers N.O 15

7.39 Three phase KWH meter, 5A, 380 V N.O 1

7.40 Single phase KWH meter, 5A, 380 V N.O 3

7.41 Three phase KVARH meter 5A ,380V N.O 1

7.42 Three phase main fused switch (LTL)3*630/400A with 3*400A HRC fuse , 400V ,120

KA . Moeller type or equivalent. N.O 1

7.43 M.C.C.B 3*400A , with external hand, NZM‐N3‐400A or equivalent .N.O 2

7.44 Four poles Motorized Automatic transfer switch ( ATS)2* (4*630A NZM‐N3‐

4*630A) or equivalent complete with motor control and with all needed

equipment and control as per drawings and according to supervisor engineer

instructions .

unit 1

7.45 MC.C.B 3*100A ‐ NZM‐B1‐3*100A or equivalent N.O 1

7.46 MC.C.B 3*40A NZM‐B1‐3*63,40A or equivalent N.O 4

7.47 MC.C.B 4*250A NZM‐N2‐4*250A or equivalent . N.O 1

7.48 Manual 12 Poles Change over 400V,630A , Type Is SECOMIC or equivalent. N.O 1

7.49 Three poles M.C. B 3X16A, (Type is Moeller or equivalent). N.O 1

7.50 Supply & Install automatic Power Factor Correction Unit complete with all

components and all needed protection devices as per drawing with , LTL 250A ,

CONTROL PANEL , 80 KVAR capacity 6 stage according to GEDCO Specifications &

Regulations with all needed according to supervisor engineer instructions.unit 1



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

7.51 Supply & install the distribution switch board No. P/DA including the following

listed components with all needed wirings,B.B. , fittings and accessories according

to specifications & supervisor instructions as follow: ‐ The frame must be made of

2mm thickness galvanized steel sheets & painted with antistatic primer paint and 2

coats of final polyester paint. The size is 80*60*20cm

N.O 1

7.52 MCB 4 poles 4*63A, 400V. (Type is Moeller or equivalent). N.O 1

7.53 Four poles ELCB 4*40A/0.03A (Type is Moeller or equivalent). N.O 1

7.54 Four poles M.C.B. 4X25A, 400V (Type is Moeller or equivalent). N.O 2

7.55 Four poles E.LC.B. ELCB 4*25A/0.03A, (Type is Moeller or equivalent).N.O 2

7.56 Four poles M.C.B. 4X40A, (Type is Moeller or equivalent). N.O 1

7.57 Two poles M.C.B 2x16A‐220V (Type is Moeller or equivalent). N.O 6

7.58 Two poles M.C.B. 2x10 A, (Type is Moeller or equivalent). N.O 26

7.59 Two poles M.C.B. 2x6A, 220V (Type is Moeller or equivalent). N.O 2

7.6 Supply& install the distribution switch board No. P/DB according to the drawing

and specifications with all needed wirings, B.B., fittings and accessories according

to supervisor instructions as follow:

‐ The Panel must be made of 2mm thickness galvanized steel sheets.

‐ The P/DB board Size is 80*60cm , includes supplying and installing the following

listed components with all needed wirings according to specifications & supervisor


N.O 1

7.61 MCB 4X63A , (Type is Moeller or equivalent). N.O 1

7.62 Four poles ELCB 4*40A/0.03A (Type is Moeller or equivalent). N.O 1

7.63 Four poles E.LC.B. ELCB 4*25A/0.03A, (Type is Moeller or equivalent). N.O 2

7.65 Four poles M.C. B 4X16A, (Type is Moeller or equivalent). N.O 1

7.66 Two poles M.C.B 2x16A, (Type is Moeller or equivalent) N.O 8

7.67 Two poles M.C.B 2x10A, (Type is Moeller or equivalent). N.O 7


7.69 Four poles M.C. B 4X25A, 380V (Type is Moeller or equivalent). N.O 1

7.7 Supply & Install the 40*60 cm distribution switch board No. P/DC according to

drawing and specifications with all needed wirings, fittings and accessories

according to supervisor instructions as follow:

The Panel must be made of 2mm thickness galvanized steel sheets

‐ The P/DC board prize includes supplying and installing the following listed

components with all needed wirings according to specifications & supervisor


N.O 1


7.72 Four poles ELCB 4*40A/0.03A (Type is Moeller or equivalent).N.O 1






Unit Rate Total

$ Amount $Item

Description

Unit Qty.

7.76 Two poles M. C. B2X16A, (Type is Moeller or equivalent). N.O 6

7.77 Two poles M. C. B2X10 A(Type is Moeller or equivalent). N.O 5

7.78 Step Relay 16A. N.O 1

7.79 Supply & Install the distribution switch board No. AC/Roof according to drawing

and specifications with all needed wirings, fittings and accessories according to

supervisor instructions as follow:

‐ The Panel must be made of 2mm thickness galvanized steel sheets

‐ size include all materials + 40% spare

‐ The AC/Roof board prize includes supplying and installing the following listed


engineer instructions

N.O 1

7.8 M.C.C.B 3X250A,380V type NZM‐N1‐3*250A (Type is Moeller or equivalent).N.O 1

7.81 M.C.C.B.3X160A,380V type NZM‐N1‐3*160A (Type is Moeller or equivalent).N.O 2

7.82 Supply& Install the 40*60CM distribution switch board No. P/Basement according

to drawing and specifications with all needed wirings, fittings and accessories

according to supervisor instructions as follow:

‐ The frame specifications are the same as mentioned for P/DA Switchboard.


‐ The P/Basement board prize includes supplying and installing the following listed



N.O 1


7.84 Two poles M. C.B 2x16A (Type is Moeller or equivalent). N.O 3

7.85 Two poles M. C.B 2x6A (Type is Moeller or equivalent). N.O 3


7.87 Supplying and install Dimming and control Lighting Panel (for hall),table mounting

Complete according to drawing and supervisor engineer’s instructions The price

includes the ,wiring, fittings, accessories and any other needed materials and

workmanship to complete the job ( also all components must be Gawiss type or

equivalent ) the board include the listed litem *The

contractor must submit shop drawing before start work

unit 1

7.88 Flash two pole on/off Switch type gawiss or equivalent N.O 9

7.89 Flash Dimmer Switch 10A/220V type gawiss or equivalent N.O 15

Cables & Manholes

Supply and install the following cable according to the drawings, specifications and

the engineer's instructions:

7.90 Supply and install underground double circuit cables XLPE (N 2XY) AL.

2x(4x150mm2) inside PVC SN8 pipes 6 inch one pipe for each cable from

proposed transformer to new MDB as per drawings, specifications, GEDCO

regulations and the engineer’s instructions, the price of cable includes pipes

warning tapes, clean sand, civil works and any other needed materials and


instructions.

L.M 100

7.91 Supply and Install 3x25+16mm2+E16mm2 copper XLPE (N2XY) cable in side 4"pvc ‐

SN8 pipes, with needed hot galvanized steel cable guard and Cable tray . from MDB

to (P/DA & P/DB ) panel. With all civil works and any other needed materials and


instructions.

L.M 60



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

7.92 Supply and Install 5*16mm2 copper XLPE (N2XY) cable in side 4"pvc ‐SN8 pipes,

with needed hot galvanized steel cable guard and Cable tray . from MDB to (P/DA

& P/DB ) panel. With all civil works and any other needed materials and


instructions.

L.M 100

7.93 Supply and Install 5*10mm2 copper XLPE (N2XY) cable in side 4"pvc ‐SN8 pipes,

with needed hot galvanized steel cable guard and Cable tray . from MDB to (P/DA

& P/DB ) panel. With all civil works and any other needed materials and


instructions.

L.M 100

7.94 Supply and Install (3x120+70+ E 70) copper XLPE (N2XY) cable in side 4"pvc ‐SN8

pipes, with needed hot galvanized steel cable guard and Cable tray . from MDB to

AC/Roof . With all civil works and any other needed materials and workmanship to

complete the job as per drawings specifications and the engineer’s instructions. L.M 40

7.95 Supply and Install (3x50+25+E25mm2) copper XLPE (N2XY) cable in side 4"pvc ‐

SN8 pipes, with needed hot galvanized steel cable guard and Cable tray . from new

MDB to old existing MDB power supply connection . With all needed civil works

and any other needed materials and workmanship to complete the job as per

drawings specifications and the engineer’s instructions , Includes Dismantle the old

cable and connect the new one

L.M 40

7.96 Supplying and executing 80cm interior diameter manhole for electrical power and

telephone cables, with 8‐ton cover, 15cm base course and all the needed materials

and workmanship to complete the job as requested by the engineer. No. 11

7.97 Supplying and executing 60cm interior diameter manhole for electrical power and

telephone cables, with 8‐ton cover, 15cm base course and all the needed materials

and workmanship to complete the job as requested by the engineer. No. 4

Stage Lighting System requirement

Supply and install the following items according to the drawings, specifications and

the engineer's instructions:



Unit Rate Total

$ Amount $Item

Description

Unit Qty.

7.98

24‐way patch panel to accommodate (24) sockets to be connected to stage spot

lighting system and dimmer panel of stage lighting. No. 1

7.99

Control Dimmer board system consists of 24‐way (dimmers) , each rated at 20A for

stage lighting and controls variable load from 80W to 2000W of tungsten lamps on

220/240V, complete with programmable, DMX Console ,DMX 24CH Dimmer Pack

in Fly Case with all accessories needed or equivalent as per drawing and the


No. 1

7.100

Supply and install pvc conduits, cables, needed for future installation of Digital

Conference System

as shown in the drawings, specifications and engineer's instructions. LS 1

7.101

Supplying and installing foundation earthing systems consisting of welding 3X35mm

galvanized steel sheets and connection to the distribution boards, R.≤5 Ohm, as per

drawings, specifications and engineer's instructions.

Digital Conference System

Supply, install, connect and commissioning complete in place and in an operatable

manner Digital Conference System similar to BOSCH or equivalent, including

equipment, installation, connection and wiring as specified in the technical

specifications and shown on drawings and the engineer’s instructions.

LS 1




Unit Rate Total

$ Amount $Item

Description

Unit Qty.

Bill No. (8) HVAC Works

8.1

Supply, install, test and commission a roof top unit of a BRAND name (US,

European, Japan only) unit to be of a cooling load 116kw, with a heat pump, with a

maximum power consumption of 48kw, unit to be with scroll compressors with

inverter for soft starting and economic control, the total air flow to be 11160cfm

with a high static pressure variable speed fan, unit to be double skin with thermal

insulation not less than 5cm fiber glass, refrigerant to be of environment friendly

R407, unit to be with all controls for protection, air control, temp. Control and work

for optimum efficiency. Unit to be with all needed accessories as per specifications,

drawings and the engineer's instructions.

Unit 2

8.2

Supply, install, test and commission a ducted concealed split unit with inverter to

be of 60,000 btu/hr, complete with filters, high static pressure fan, flexible

connection, electrical control panel, copper cooling coil, remote control, room

thermostat, and an outdoor unit with the galvanized steel base, heat pump reverse

cycle for heating, scroll compressor and all related works as per specifications,

drawings and the engineer's instructions.

Unit 1

8.3

Ditto, but decorative type, of a cooling capacity of 12000btu/h, with inverter type

as per specifications, drawings and the engineer's instructions. Unit 4

8.4

Supply, install and commission an aluminum adjustable air outlets for distributing

the air, a jet type is required to supply the air to the bottom, square or round type

is acceptable, the air volume to be of 530 cfm, color to be specified by supervisor.

All to be executed as per specifications, drawings and the engineer's instructions. No. 63

8.5 Ditto, but for return air, grill type. No. 12

8.6 Ditto, but of size 60x60cm. No. 2

8.7 Ditto, but air louver 200x80cm. No. 2

8.8

Supply, fabricate, install and commission hot dip a galvanized steel metal sheet

duct of thickness 0.7‐1.0 mm for supply air and return air, according to the

drawings and duct standards (SMACNA), duct to be with thermal insulation of fiber

glass 24kg/m3, and 1‐inch thickness (Indoor the building), with all dampers,

splitters, fasteners, screws and all related works. All to be executed as per

specifications, drawings and the engineer's instructions.

M2 450

8.9

Ditto, but for external the building, to be with 5cm thickness insulation of 48kg/m3

fiber glass, duct to be with an aluminum cladding of 0.5mm thickness.

All to be executed as per specifications, drawings and the engineer's instructions. M2 50

8.10

Supply & cast ready mix concrete 200 kg/cm2 under the HVAC roof top units 20cm

thick with steel mesh 10 mm diameter every 20cm and 5.0cm polystyrene as

shown on the drawings, specifications and the engineer's instructionsM2 50


Bill No. (9) Miscellaneous Works

9.1 Supply and fix fire extinguisher, 6kg capacity filled with CO2, fixed at 2m height. As No. 2

9.2 Ditto but filled with dry powder 3.0kg. No. 2




Unit Rate Total

$ Amount $Item

Description

Unit Qty.

SUBTOTAL OF (A) M.P.H Building

1Bill No. (1) Excavation & Earth Works

2Bill No. (2) Concrete & Block Works

3Bill No. (3) Finishing Works

4Bill No. (4) Carpentry & Joinery Works

5Bill No. (5) Aluminum & metal Works

6Bill No. (6) Plumbing & Sanitary Works

7Bill No. (7) Electrical Works

8Bill No. (8) HVAC Works

9Bill No. (9) Miscellaneous Works

‐SUB TOTAL


B LABS Building

Unit Rate Total

$ Amount $

(B) Labs Building

Construction Works : Labs Building

Bill No. (1) Excavation & Earth Works

1.1 Excavation for foundations from natural ground level up to the

required designed level. The works including:

‐ The compaction of the soil surfaces to get (98% MDD).

‐ The excavated material should be removed out from the site to the

approved places.

‐ All to be executed as per specifications, drawings and the engineer’s

instructions.

M3 220

1.2 Supply, fill by using approved material (clean sand) around the

foundations & inside the building up to the required levels, which shall

be spread in layers not exceeding 25cm each one & compacted (98%)

to reach up the required levels (under floor slab), according to the

specifications & the engineer's instructions.M

3 180


Item

Description

Unit Qty.


B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

Bill No. (2) Concrete & Block Works

A‐ Concrete Works


‐ All form works and shuttering in any form, shape and size. Making

chamfered and curved edges, allowing for and making grooves and

sleeves and the like; removal of forms and cleaning of all exposed tie

wires and rods; making good the harmed surfaces and edges and all

surface finishing.

‐ Supplying, Casting, vibrating and curing as per specifications.


‐ Incurred costs on Concrete Mix Designs, Sample taking, testing and

providing test results certificates, storing and saving of samples.

‐ Supplying reinforcement of any grade, size and length as detailed in

the drawings, storing on site including cutting, bending and fixing in

position and providing all tying wires, spacers, shop drawings, testing

and bar bending schedules

‐ Painting of exposed surfaces of underground reinforced concrete

elements with primer and two coats of hot bituminous paint (75/25),

the strokes of each layer to be opposite to each other.

‐ Underground concrete elements prices are including expansion

joints, flexcell sheets 18mm thick & mastic.

‐ Steel bars used for alignment and fixing of reinforcement works, and

extra steel added to assure proper detailing and safety.

‐Supply & spread polythene sheets gauge 500 under the foundations &

ground slabs.

‐ Measurement of Concrete elements shall be the net dimensions as

detailed in the drawings. All recesses openings and voids shall be

deducted.

‐ Measurement shall be only for the seen surfaces of elements.

Overlapping and measuring items twice under separate headings shall

not be allowed.

‐ Columns are to be measured from the top level of the slab to the

bottom level of the beam or dropped beam.

‐ The concrete surface must be finished with mechanical steel trowel

machine.

All works must be done as per drawings, specifications & the


2.1 Supply & cast plain concrete (200kg/cm2) under the foundations.M3 5

2.2 Supply & cast ready mix concrete (300kg/cm2) for reinforced concrete

foundationsM

3 38

2.3 Supply & cast ready mix concrete B300 for columns necks as shown on

the drawings, specifications and the engineer's instructions. M3 2


B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

2.4 Supply & cast ready mix concrete B300 for tie ground beams.M

3 15

2.5 Supply & cast ready mix concrete B250 for ground slab 10cm thick with

steel mesh T8/20cm each way. M2 205

2.6 Supply & cast ready mix concrete B300 for columns as shown on the

drawings, specifications and the engineer's instructions. M3 20

2.7 Ditto but B200 for stop columns at roof.M3 2

2.8 Supply & cast ready mix concrete B300 for suspended hollow block

slabs 30cm thick, including the hollow cement blocks, reinforced

concrete hidden, inverted & drop beams & all the required materials. M2 700

2.9 Supply & cast ready mix concrete B250 for doors & windows lintels,

sills & canopies including all the required materials. M3 23

2.10 Ditto, but for parapet walls coping & external concrete elements.M

3 3

2.11 Supply & cast ready mix concrete B200 under the elevated water tanks

20cm thick with steel mesh 10 mm diameter every 20cm and 5.0cm

polystyrene as shown on the drawings, specifications and the


M2 6

B‐ Block Works: ‐

2.12 Supply & build hollow block walling 20cm thick including the supplying

of all materials (block size 20 x 20 x 40cm). M2 500







B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

Bill No. (3) Finishing Works

3.1 Supply & execute internal plastering 13mm thick to walls, soffits &

columns including galvanized metal lath angles for columns, edges &

chicken wire at the intersection of concrete & block works, pipes &

cement rendering as per the engineer's instructions.M2 1100

3.2 Ditto but for cielings according as per specifications and engineer

instructions. M2 650

3.3 Ditto, but for external plastering 15mm thick to walls and soffits the

price including additional layer of 5mm thick lime free mortar (mix 1:

3) as per specs, drawings and the engineer’s instructions.M2 100

3.4 Supply and install west bank smooth stone 5.0 cm thick with backing

filling 5.0cm (Grade B‐200) with steel mesh 6mm dia @ 20cmm as per

the engineer's instructions.M2 150

3.5 Ditto but Molatash 5.0 cm thick with backing filling 5.0cm.M

2 500

3.6 Supply and install terrazzo floor tiles (grade A) size 25x25x2.5cm with

Basalt stone laid on 2cm mortar bed and 5 cm thick sand bed and

terrazzo skirting 25x7x1cm including all materials and testing as per

the engineer's instructions.M2 550

3.7 Supply and cast terrazzo edge beam 20cm x10cm of the same kind

and color of the floor tiles including smoothing the surfaces and edges

(for corridors) as per the engineer's instructions.M2 10

3.8 Supply and install local marble (grade A) size 34cm wide x 3cm thick

laid on 2 cm thick mortar bed as per specifications, drawings, and the


The item shall include suppling and installing 2cm local marble

between the aluminum window and the mentioned marble, this

marble has the same aluminum window depth.

RM 50

3.9 Ditto but size 36 cm wide x 3cm thick for roof parapet. RM 70

3.10 Ditto but size 30 cm wide x 3cm thick for corridors parapet.RM 60

3.11 Ditto but threshold size 23 cm wide x 3cm thick for doors.RM 20

3.12 Supply and erect marble 2 cm thick for buffet and canteen 400 cm

lengths, 60 cm wide and 87 cm high including vertical dividers, internal

horizontal shelves, back of cupboards, floors and granite (Tiger eye) for

the top surface with round edges, skirting 10 cm high and making the

needed opening for basins as shown in drawings. The work shall also

include the cupboard leaves, drawers which will be made of 17mm

plywood covered with colored Formica 0.5mm sheets from both sides

Unit 1

3.13 Supply and install high quality Granite 593x90x2cm thick (Tiger Eye) for

top cover of experiment chemistry lab preparing bench. The price shall

include the local marble grade A, supports, shelves, all accessories,

granite skirting 10 cm high, all accessories, fittings, making holes for

basin and water and gas supply, water mixer, cold and hot water

networks, drainage network, and gas supply distribution network in

accordance with the specs, drawings and the engineer's instructions.

Unit 4


B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

3.14 Supply and install high quality Granite 257x75x2cm thick (Tiger Eye) for

top cover of demonstration chemistry lab bench. The price shall

include the local marble grade A, supports, shelves, granite skirting 10

cm high, all accessories, fittings, making holes for basin and water and

gas supply, water mixer, cold and hot water networks, drainage

network, and gas supply distribution network in accordance with the

specifications, drawings and the engineer's instructions.

Unit 1

3.15 Ditto but for physical lab demonstration bench without gas supply.Unit 1

3.16 Supply and install colored none slipping ceramic (grade A) 8mm thick

for floor.M

2 80

3.17 Supply and install colored glazed wall tiles (grade A) 6mm thick laid on

2cm mortar (1:3).M2 260

3.18 Supply and paint, external soffits, sloping soffits, facade and external

columns with one coat of bondrol primer and at least two coat of

External quality of colored emulsion paint (Supercryle) or equal

approved as per specifications, drawings and the engineer's

instructions.

M2 100

3.19 Supply and paint the internal walls up to a high of 2.2m above finishing

floor level two coats of putty, one undercoat primer and two coats of

colored oil paint as per specs, drawings & the engineer's instructions. M2 550

3.20 Supply and paint one primer and minimum two coats of emulsion

paint (Poliside) for internal walls, ceiling and drop beams as per

specifications, drawings & the engineer's instructions.M2 1000

3.21 Supply and cast foam concrete with fine aggregates for roof screening of ranging thickness from 4 to 15 cm and sand angle fillets size 5cmx5cm as per specifications, drawings and the engineer's instructions .

M2 227

3.22 Supply and lay one layer of plasticized bitumen roofing membrane with chipping 4 mm thick, including priming concrete surface prior to laying, dressing into rain water outlets to form water proofing seal and cover the angle fillets. The rate include verticals parts skirting as per specification and drawings.Note: Measurement will be for the horizontal projection

M2 227

3.23 Supply and execute expansion joint at the roof as detailed in drawings

including flexcell sheets 18mm thick, (THIOMOFLEX 600) mastic 20mm

thick and all reinforced concrete inverted beams & other elements as

per drawings, specifications & the engineer's instructions.RM 10

3.24 Supply and execute expansion joint on the floors as detailed in

drawings including flexcell sheets 18mm thick, 20x30mm (NETO 280)

mastic, 2 Nos. of galvanized steel angle size 75x75x5mm & 1.0m wide

strip of self‐adhesive membrane 4.0kg/m2 as per drawings,

specifications and the engineer’s instructions.

RM 7

3.25 Supply and execute expansion joint at sides of walls and columns as

detailed in drawings including flexcell sheets 18mm thick,

(THIOMOFLEX 600) mastic 20mm thick & cover the joints with

aluminum strip size 75x6mm or aluminum angle 57x57x6mm fixed to

aluminum strip 37x6mm screwed to the walls or the soffits from one

side, as per drawings, specifications and the engineer’s instructions.

RM 15



B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

Bill No. (4) Carpentry & Joinery Works

The items include supplying carpentry works from good wood include

frame cover mold, architrave, galvanized steel frame, concrete filling

200kg/cm2, 20cm Aluminum kick plates, hard ware lock type Wally

switch or approved equivalent and brass hinges 10cm height and all

other fittings, colored Formica, primer, undercoat and two coats of

color paint, all as per specifications, drawings, the engineer’s

approval.

4.1 Supply, fix and paint wooden single internal flush door type D2 size

80x220x4.5cm according to the drawing, specifications and under

supervision.

No. 6

4.2 Ditto, but for type D3, overall size 70x 220x4.5cm thick. No. 12

4.3 Supply and fix 120x20mm soft wood coat hook rail smoothed, plugged

and screwed to wall at 30cm center to center including priming and

sanding sealer and two coats of varnish painting with Galvanized steel

coat hook screwed to rail at 20cm center to center as per the


RM 8

4.4 Supply and fix soft wood rubbing rails size 200mm x 20mm with round

edges, smooth surface, apply two coats of sanding sealer, sand lightly

and apply two coats of varnish, drill and fix to concrete or block walls

using expansion steel bolts.

RM 45

4.5 Supply and install wall mounted magnetic white marker board , 25 mm

profile KALBOARD MW 3612/CR size 120x360 cm) with silver anodized

elegant aluminum frame (19x25mm thick) and four strong rounded

plastic (upvc) corners fixed internally with screws to the wall, and also

with silver anodized aluminum try fixed by sliding through the profile

which used for markers and duster and has UPVC edges for safety.

The writing surface coated of Porcelain fixed by using automatic gluing

machines to 11mm thick MDF wood covered automatically by

aluminum foils. Price to include all related works as per drawings,

specification and Engineer’s Instructions. the price shall include

removing the existing boards and handled to the owner.

No. 4



B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

Bill No. (5) Aluminum & Metal Works

. The rates of the following items shall be Completed in accordance

with drawings, specifications, details and as directed by the engineer.

. Door frames shall fit walls & sizes of door openings, taking into

consideration the thickness of plastering on both sides of the frames.

. Hardware for doors shall be Waley type with approved handles.

. The aluminum windows are colored powder coated aluminum

Jordanian type 7000 / 4500 or approved equivalent with sliding

leaves, frame, clear glass 4mm thick, fly screen ironmongery, and

hardware and aluminum accessories.

. The aluminum will be tested in approved testing laboratory.

. The contractor has to submit shop drawings to the engineer before

fabrication and installation.

5.1 Supply & install Mul‐T‐Lock door type 417 with overall size 125cm

width x 220cm height (D1) with powder coated paint. Door lock type

235 & Mul‐T‐Lock serrated cylinder. All to be carried out according to

the specifications, drawings & the engineer's instructions.

No. 4


5.3 Supply and fix powder coated colored aluminum window type "W1"

size 220 cm width x 120 cm height, (model 7000) sliding leaves, fly

screen leaves, frame, clear glass 4mm thick, ironmongery, and

hardware and aluminum accessories. All as per specifications,

drawings and the engineer’s instructions.

No. 12


5.5 Supply and fix powder coated colored aluminum type model 4500 for

window type "W3" size 100cm width x 70cm height with two hinged at

the mid, unclear glass 4mm thick, ironmongery and hardware as per

specifications and drawings.

No. 6

5.6 Supply & fix galvanized steel protection for external Windows size

220x120cm type "W1", the prices including all the galvanized steel, the

fixation accessories, painting with one primer coat & two coats of oil

paint, all according to the drawings, specification and engineer’s

instructions.

m2 12

5.7 Supply and fix galvanized steel protection for internal windows overall

size 240x70 cm type (W2), the prices including all the steel, the fixation

accessories, painting with one primer coat & two coats of oil paint, all

according to the drawings, specification and engineer’s instructions.

No. 6

5.8 Ditto, but for windows type "W3" size 100cm width x 70cm.No. 6

5.9 Supply & fix galvanized steel protection for external Windows size

220x67.52cm type (W1),at first & second floors, the prices including all

the galvanized steel, the fixation accessories, painting with one primer

coat & two coats of oil paint, all according to the drawings,

specification and engineer’s instructions.

No. 8

5.10 Supply & fix mild steel balustrade 60cm high for corridor at ground

floor comprising of mild steel hollow section tubes 40 x 20 x 2 mm

verticals spacing 15 cm center to center, & welded to mild steel hollow

section coping 60x40x3 mm top & hollow section tube 60x40x3 mm

bottom, the price includes mild steel end angles & plates, painting with

one primer, one under coats & minimum two coats of oil paint, (the

color to be approved by the Engineer, all as per specifications,

drawings & the engineer's instructions.

RM 30



B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

Bill No. (6) Plumbing & Sanitary Works

. The rates of the following items shall be completed in accordance

with the drawings; specs, details and as directed by the engineer.

. The contractor must submit the shop drawings to the engineer's

approval before starting the work.

. The contractor must submit the as built drawings to the engineer's

approval after completing the work.

. All materials used for plumbing works shall be of high quality

materials based on the British standards and must be approved by the

engineer, the price shall include fittings, connections, accessories,

testing and all the needed materials to complete the job according to

the specifications, conditions of contract, drawings & engineer’s

approval.

. The used cold water pipes are galvanized steel pipes (Akko) / HDPE

pipe.

. The used hot water pipes are galvanized steel pipes (Akko) with heat

insulation (Armoflex) / HDPE pipe.

. The drainage pipes (UPVC, Fittings ... etc.) from Holiout must be

according to the drawings & engineer's instructions.

. All fittings, accessories, valves, brackets, connections and all the

needed materials to complete the job are included.

. Chlorination, flushing & testing must be carried out according to the

specifications & the engineer’s instructions.

6.1 Supply and fix white glazed porcelain hand wash basin size 50cm x

41cm (Vitra type 6602+6173) or approved equivalent, complete with

all water supply pipes ½", waste fitting, trap, plug and chain, chromium

plated water mixer 1/2" dia. Jack type) (From Artema‐Armix or Hamat

or approved equivalent) and mirror 60x60cm, Supply & fix white

glazed soap tray tiled into block walls, steel brackets supports and the

drainage line to floor trap 2”, all needed accessories & the pipe

concrete encasement as per specifications, drawings and the


No. 12

6.2 Supply & fix porcelain kitchen sink with two bowls built in the granite

work top for buffet including water supply pipes ½”, waste fitting, trap,

plug & ½" swan neck chromium plated water mixer 1/2" dia. Jack type)

(From Artema‐Armix or Hamat or approved equivalent) & the

drainage line to floor trap & all needed accessories. All as per specs,

drawings and the engineer instructions.

No. 1

6.3 Supply & fix white glazed porcelain squatting W.C. suite (HARSA

EUROPEAN ‐ TYPE or approved equivalent) complete with porcelain

flushing cistern, pip hose, 1/2" dia. UPVC 100 cm long flushing pip hose

for toilets, seat & plastic cover, white glazed toilet paper holder tiled

into block walls (size 15cmx15cm), 4" dia. P.V.C. drainage pipe to the

nearest main drainage line, all needed accessories & the pipe concrete

encasement (as shown in the drawings (Vitra‐Normus or approved

equivalent).

No. 12


B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

6.4 Supply & fix 1.5" dia galvanized pipe for main water supply connected

from the existing water pump line to the building network as shown on

the drawings & as per the engineer’s instructions, the price shall

include all the necessary fittings, valves, excavations, backfilling,

concrete encasement & all needed materials to complete the job.

RM 75

6.5 Supply & fix 1" dia. galvanized pipe inside pvc 2” sleeve pipe for drop

water pipe connected from the school roof tanks to the water line as

shown on the drawings and according to the engineer’s instructions,

the price shall include all the necessary fittings, valves, excavations,

backfilling, concrete encasement & all needed materials to complete

the job.

RM 15

6.6 Ditto but 1.5" dia for water risers and distribution lines embedded in

block works or lay under floor tiles or on roofs.RM 15

6.7 Ditto but HDPE dia. 3/4" dia for cold water. RM 240

6.8 Supply and install UPVC pipes 6” diameter for drainage, with sockets

joint 4.7 mm wall thickness. The work shall include the excavation,

backfilling, jointing, and the pipe concrete encasement……. etc. to

complete the job as per specifications, drawings and the engineer's

instructions.

Also connect the sewer networks with the existing manhole as per

drawings; the work shall include the municipal fees and all the needed

material to complete the job as per the engineer's instructions.

RM 15

6.9 Supply and install UPVC pipes 4” diameter for drainage, with sockets

joint 3.2 mm wall thickness. The work shall include the excavation,

backfilling, jointing, and the pipe concrete encasement……. etc. to

complete the job as per specifications, drawings and the engineer's

instructions.

RM 95

6.10 Supply and install UPVC pipes 3” diameter for rain water drainage

pipe, with sockets, pipe joints, caps, supports and all needed materials

to complete the job as per specifications, drawings and the engineer's

instructions.

RM 35

6.11 Ditto but 4” diameter for vent‐pipe. RM 10


B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

6.12 Supply and fix floor trap 4" diameter, complete with heavy duty brass

grating & UPVC pipe to the nearest inlet with the pipe concrete

encasement as per specifications, drawings and the engineer's

instructions.

No. 28

6.13 Supply and install concrete manhole of internal diameter 60cm, and

(50‐90) cm depth according to the required level, 12cm thick plain

concrete for walls and base, slab, with cast iron cover with 8 ton

bearing capacity according to I.S, specifications and drawings.

No. 4

6.14 Supply & install 1.5 m3 local made black polyethylene water tank with

lockable cover, fittings, vent pipes, overflow, drain, connections, galv.

Steel tank stand, valves, float switches & the required accessories

according to the drawings, specs & engineer's approval.

the item shall include supply & install galvanized steel stand for water

tank with all the required accessories rest on 30x30x3.0cm thick

marble footings according to the drawings, specifications & engineer's

approval.

No. 3

6.15 Supply, install and fix gas system with control valves (S&B or

equivalent), gauge pressure (16bar, R & R or equivalent), wooden gas

junction box size 40x40x20cm including one leaf cover and 3x36kg gas

cylinders and all gas pipes, burners, connection and all accessories

needed to complete the gas network and connect the gas to the

benches to gas valves (SG‐1 Sagir or equivalent) for Labs units, all

according to the drawings, specifications & the engineer's instructions.

L.S 1

6.16 Supply and install an approved water distribution galvanized steel

2mm thick cabinets with galvanized steel doors with switch locks and

hammer paint for the distribution water network with any number of

cold water & hot water outlets with polythene pipe HDPE 16 mm

distribution pipes and the connection from the main supply drop pipe

G.S.P. to the distribution cabinets, air valves, gate vales, unions,

supports and all accessories needed to complete the job, all according

to the drawings, specifications & the engineer's instructions.

No. 3



B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

Bill No. (7) Electrical Works

The prices of all electrical works and installed equipment and

components listed below includes:

‐ Shop drawings ‐ As built ‐ ...

‐ Execution of all needed works & install all fittings and accessories

required for operation.

‐ All materials supplied (such as wires, pipes, electrical

equipment…etc.) should be of the best quality and must be approved

by the supervising engineer.

‐ The work includes maintenance period for each device according to

tradition in the field.

‐ Oversees the installation and maintenance, a specialist in the field of

devices

‐ Supply, Erect & Commission the electrical equipment according to

the drawings, specifications and the engineer's instructions. Also the

work shall include workman ship and all accessories needed to

complete the job.

7.1 Supply and install LED lighting fixture 2X24w complete with driver,

type GA’ASH model Batten LED, or equivalent, including 120cm day

light lamps T8, 6500 ,2500Lm each lamp, 3X1.5 mm2 wires, conduits,

clamps and bolts, and connection boxes, and all other fitting and

accessories. needed to complete work as per drawing and specification

and engineer instruction.

No. 48

7.2 Ditto but 1x24w with special reflector for black board.No. 8

7.3 Ditto, but ceiling round luminaire, water proof IP65, 16w LED ,4000

complete with driver, type GA’ASH model Hermon or equivalent As

per drawings and specification and engineer instruction.No. 20

7.4 Supply and install single pole 10A, 220V, ON/OFF switch, the work shall

include all the needed accessories such as wires 3x1.5mm2, pipes,

boxes, covers, fixing bolts, connection……...etc. The type is Gewiss or

approved equivalent.

No. 12

7.5 Ditto, but single pole waterproof switch.No. 6

7.6 Ditto but single pole, two‐way switch, single pole, 10A, 220V (fixel).No. 4

7.7 Ditto but, flush mounting socket outlet (2P+E) 10/16A, including

3x2.5mm2 wires, covers, conduits, bolts, clamps, and connection

boxes, complete with all accessories for connection and

commissioning.

No. 20

7.8 Ditto but Waterproof socket outlet (2P+E) 10/16A, including 3x2.5mm2

wires, covers, conduits, bolts, clamps, and connection boxes, complete

with all accessories for connection and commissioning.No. 42

7.9 Ditto but telephone socket including 2 pair telephone cable complete

with all needed wire and accessoriesNo. 6

7.10 Supply and install 10” school electrical bell with two push buttons,

including wires, conduits, clamps, bolts connection boxes ……. Etc, all

according to the drawings, specifications & the engineer's instructions.No. 1

7.11 Supplying and installing electrical ceiling fan 220V\125W, with its

wires, conduits, switch, connections…. etc. Type is CHMC or approved

equivalent.No. 12


B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

7.12 Supplying and installing, 2x60W RMS REAL, amplifier with two horn

loud speakers waterproof type, 50 W each, two microphones, and

connections…. etc. including conduits, 2 cables for loud speakers, and

all needed accessories.No. 1

7.13 Supplying and installing amplifier socket out let, waterproof type,

including conduits, sockets and speakers’ cables 3x2.5 mm2 with all

needed accessories.No. 2

7.14 Supplying and installing foundation earthing systems consisting of

welding 3X35mm galvanized steel sheets and connection to the

distribution boards, R.≤ 3 Ohm, as per drawings, specifications and

engineer's instructions.L.S 1

7.15 Supplying and executing 60cm interior diameter manhole for electrical

power and telephone cables, with 8‐ton cover, 15cm base course and

all the needed materials and workmanship to complete the job as

requested by the engineer.

No. 3

Distribution Switch Boards

7.16 Supply& Install the Sub distribution switch board No. SDB/G according

to drawing and specifications with all needed wirings, fittings and

accessories according to supervisor instructions as follow:


‐ The SDB/G board prize includes supplying and installing the listed

below components with all needed wirings according to specifications

& supervisor engineer instructions.

No. 1

a Four poles M.C.B. 4X40A, (Type is Moeller or equivalent). No. 3

b Four poles M.C.B. 4X25A, 400V (Type is Moeller or equivalent). No. 1

c Four poles E.LC.B. ELCB 4*25A/0.03A, (Type is Moeller or equivalent).No. 1

d M.C.B. 3X10A, (Type is Moeller or equivalent).No. 1

e Four poles E.LC.B. (R.C.C.B.) 4X10A, 380V ABB/F204A‐40/0.03A or

equivalent. No. 1

f Four poles M.C.B. 4X20A, 400V (Type is Moeller or equivalent). No. 2

g One poles M.C.B 1x16A‐220V (Type is Moeller or equivalent). No. 4

h One poles M.C.B 1x10A‐220V (Type is Moeller or equivalent). No. 4

7.17 Supply& Install the Sub distribution switch board No. SDB/F (first floor

) according to drawing and specifications with all needed wirings,

fittings and accessories according to supervisor instructions as follow:


‐ The SDB/F board prize includes supplying and installing the listed



No. 1

a Four poles M.C.B. 4X20A, 400V (Type is Moeller or equivalent). No. 1

b Four poles E.LC.B. ELCB 4*25A/0.03A, (Type is Moeller or equivalent).No. 2

d M.C.B. 3X10A, (Type is Moeller or equivalent). No. 1

e M.C.B. 3X16A, (Type is Moeller or equivalent). No. 1

f One poles M.C.B 1x10A‐220V (Type is Moeller or equivalent). No. 4



B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

7.18 Supply& Install the Sub distribution switch board No. SDB/S (Second

floor ) according to drawing and specifications with all needed wirings,

fittings and accessories according to supervisor instructions as follow:


‐ The SDB/S board prize includes supplying and installing the listed



No. 1

a Four poles M.C.B. 4X20A, 400V (Type is Moeller or equivalent). No. 1

b Four poles E.LC.B. ELCB 4*25A/0.03A, (Type is Moeller or equivalent).No. 2

d M.C.B. 3X10A, (Type is Moeller or equivalent). No. 1

e M.C.B. 3X16A, (Type is Moeller or equivalent). No. 1

f One poles M.C.B 1x10A‐220V (Type is Moeller or equivalent). No. 4


7.19 Supply and install computer Patch Panel, type ORLAN or 3 COM or

equivalent, for 24 computer data outlets CAT6, with connections,

name plates and numbering.No. 2

7.20 Supply and install computer data switch type Cissco or equivalent, 24

ports, including connections, name plates and numbering. No. 2


Bill No. (8) Miscellaneous Works

8.1 Supply and fix fire extinguisher, 6kg capacity filled with CO2, fixed at

2m height. As per specification, drawings and according to the

Palestinian fire defence department's requirements. No. 2

8.2 Ditto but filled with dry powder 3.0kg. No. 2



B LABS Building

Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

SUBTOTAL OF (B) LABS Building

1 Bill No. (1) Excavation & Earth Works

2 Bill No. (2) Concrete & Block Works

3 Bill No. (3) Finishing Works

4 Bill No. (4) Carpentry & Joinery Works

5 Bill No. (5) Aluminum & metal Works

6 Bill No. (6) Plumbing & Sanitary Works

7 Bill No. (7) Electrical Works

8 Bill No. (8) Miscellaneous Works

‐ SUB TOTAL


Unit Rate Total

$ Amount $

( C) Construction Works : External

A –The Demolishing, Earth & Tiling Works:

1 Carefully demolish the existing external steps and reinstate the

works to its original conditions as shown in the drawings and in

accordance to the engineer's instructions. The price includes

removing of all the debris from site to approved places.

L.S 1

2 Leveling from natural ground level up to the required site designed

levels. The works including:

The compaction of the soil surfaces to get (98% MDD). The

excavated material should be removed out from the site to the

approved places as per specs, drawings and the engineer's

instructions.

M2 400

3 Supply, fill by using approved material (clean kurkar), which shall be

spread in layers not exceeding 25cm each one & compacted (98%) to

reach up the required levels according to the specifications & the


M3 200

4 Supply, spreading, levelling, damping and compacting 20cm (M.D.D

100%) of base coarse material according to the drawings,

specifications and the engineer's instructions.M

2 100

5 Supply, spread, lay, colored interlock tiles 6cm thick, the price

includes 5 cm clean sand, 10cm (M.D.D 100%) of base coarse

material compacting, tiles, testing as per specification, drawing & the

engineer's instructions, the interlocking tiles shape & color must be

approved by the engineer.

M2 370

B ‐Retaining Wall Works.

Earthing Works:

6 Excavation from natural ground level to required retaining walls

foundations designed level. The works include the compaction of the

soil surfaces to get (98% MDD). The excavated material should be

removed out from the site to the approved places as per the


M3 80

7 Supply, fill by using approved material (clean sand) around the

foundations, which shall be spread in layers not exceeding 25cm

each one & compacted (98%) to reach up the required levels

according to the engineer's instructions.M

3 55

Item

Description

Unit Qty.


Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

Concrete Works


‐ All form works and shuttering in any form, shape and size. Making

chamfered and curved edges, allowing for and making grooves &

sleeves and the like; removal of forms & cleaning of all exposed tie

wires & rods; making good the harmed surfaces & edges & all

surface finishing.

‐ Supplying, Casting, vibrating & curing as per specifications.


‐ Incurred costs on Concrete Mix Designs, Sample taking, testing and

providing test results certificates, storing and saving of samples.

‐ Supplying reinforcement of any grade, size & length as detailed in

the drawings, storing on site including cutting, bending and fixing in

position and providing all tying wires, spacers, shop drawings,

testing and bar bending schedules .

Painting of exposed surfaces of underground reinforced concrete

elements with primer and two coats of hot bituminous paint

(75/25), the strokes of each layer to be opposite to each other.

‐ Steel bars used for alignment and fixing of reinforcement works,

and extra steel added to assure proper detailing and safety.

‐ Measurement of Concrete elements shall be the net dimensions as

detailed in the drawings. All recesses openings and voids shall be

deducted.

‐ Measurement shall be only for the seen surfaces of elements.

Overlapping and measuring items twice under separate headings

shall not be allowed.

‐ The concrete surface must be finished with mechanical steel trowel

machine.

‐he prices shall include Supply & spread polythene sheets gauge 500

under the foundations & ground slabs.

All works must be done as per drawings, specifications & the


8 Supply & cast plain concrete B150 under the foundations.M

3 3

9 Supply & cast ready mix concrete B300 for reinforced concrete

foundations and retaining walls (weep holes to be provided). M3 30

10 Ditto, but for external steps. M3 8


Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

Finishing Works:

The price shall include the supply of all materials, galvanized

angles, galvanized mesh, mixing, scaffolding, curing, site cleaning,

equipment and workmanship required to complete the job

according to the specifications, drawings & engineer's approval.

11 Supply & execute external plastering 15mm thick to walls and soffits,

the price shall include additional layer of 5mm thick lime free mortar

(mix 1:3) as per specs, drawings & the engineer’s instructions. M2 100

12 Supply & execute two coats of Tyrolean finish with white cement &

painting with one coat of superbondrol then apply two coats of

colored emulsion paint (Supercryle) for boundary wall according to

specs & the engineer's instructions.M

2 100

13 Supply and lay local marble stair treads size 36 cm wide x 3cm thick

chamfered once, rebated once and laid on 2cm thick mortar bed and

the price includes marble stair risers size 12.0cm or 12.5 high x2cm

thick and skirting 7/20cm high x2cm thick as per specs, drawings and

the engineer ‘s instructions.

RM 60

D‐ Planting Works:

Supply, plant and maintain the flowing plants, trees & grass

including all needed materials & workmanship to complete the job

according to the drawings, specifications and the engineer’s

instructions for the following items: ‐

14 Supply, fill and spread agricultural soil of not less than 30cm thick up

to the required levels for the green areas as shown in the drawings,

specifications and the engineer’s instructions. M2 35

15 Relocate some of the existing trees by replanting them to new

locations including all the needed materials to complete the job as

shown in the drawings, specs and the engineer’s instructions. No. 7

16 Supply and plant climbers (BOUGAINVILLEA), (6‐8) litter pot, height

is more than 1.0 meter and girth not less than 1.5cm as per the

engineer instructions. No. 5


Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

E‐ Plumbing and Sanitary Works

17 Supply & install stainless steel drinking unit (cylindrical shape) 1.5m3

capacity, 1.5mm thick wall thickness composed of 12 Nos. of self‐

pushing water taps 1/2" dia., stainless steel taps covers, inlet

stainless steel pipe 3" dia. with elbow & firefighting connection,

stainless steel vent pipe 3/4" dia. with elbow, level guide, 30cm dia.

Stainless steel cover 4mm thick with gasket, 4 No. of stainless steel

profile 80x80x3mm legs with 80cm height, 4 Nos. of stainless steel

bolts for each leg, stainless steel drainage pipe 2" dia. connected to

the nearest manhole & all needed fittings & materials to complete

the job, the price also includes the supplying & casting of the

reinforced concrete footings size 200x200x30cm with double steel

mesh 10mm dia. each 20cm as per drawings, specifications & the


No. 1

18 Supply & fix 1.5" dia. galvanized pipe for main water supply

connected from the existing main water line & the water tanks as

shown on the drawings & as per the engineer’s instructions, the

price shall include all the necessary fittings, valves, excavations,

backfilling, concrete encasement & all needed materials to complete

the job.

RM 30

19 Ditto but 1" dia for water distribution lines. RM 20

20 Ditto but 3/4" dia for garden water lines. RM 50

21 Supply & fix 3/4" dia. Garden water tap.No. 3

22 Excavate and construct percolation pit with a depth of 5.0 m and

inside diameter of 2.50 m with a special block for percolation pit,

supply and install reinforced concrete 300 Kg/cm2 with thickness of

25 cm for the cover of the percolation pit and supply and install cast

iron cover (8.0‐ton capacity and 60 cm opening diameter). The price

includes supplying and laying well graded aggregate of thickness of

40 cm at the bottom of the pit, backfilling around the pit with kurkar

in layers 20cm thick each and compaction 98% MDD and connect the

existing house sewer to the pit with approved pipe type & diameter,

removing the surplus soil to the tip.... etc. to complete the job as per

drawing and Engineer’s instruction.

No. 1


Unit Rate Total

$ Amount $

Item

Description

Unit Qty.

F‐ Miscellaneous Works

23 Supply & lay Hydraulically pressed to BS 7263 pre‐cast concrete

kerbstones for the sidewalks with size of (15x30x100cm) including all

necessary excavations, filling with dune sand & compaction to 98%

of MDD, the base coarse layer (30x13 cm), 200Kg/cm2 plain

concrete foundation (27x12cm) under the kerb and (21x12cm)

backing behind, spreading 2 cm mortar under the kerb, filling joints

between kerbs with cement mortar and painting with one prime

coat and two finishing coats of approved brand name painting

material ,expansion joint every 12 meter with selotex board and

filling 3cm with seka.

RM 110

24 Supply and cast R.C. ready mix concrete B 250 for the external steps

ramps and others. M3 20

25 Supply and cast ready mix plain concrete 200 kg/cm2 under the

external steps, and others. M3 5

26 Supply & fix mild steel balustrade 80cm high for corridor at ground

floor comprising of mild steel hollow section tubes 40 x 20 x 2 mm

verticals spacing 15 cm center to center, & welded to mild steel

hollow section coping 60x40x3 mm top & hollow section tube

60x40x3 mm bottom, the price includes mild steel end angles &

plates, painting with one primer, one under coats & minimum two

coats of oil paint, (the color to be approved by the Engineer, all as

per specifications, drawings & the engineer's instructions.

RM 40

27 Supply & install smooth surface pre cast reinforced concrete B300

seat size 180x45cm, the price includes the painting of the seats with

one coat of Superbandrol & at least two coats of colored emulsion

paint (Supercrelye) according to the drawings, specs and the


No. 13

28 Supply and fix galvanized steel bin 3mm thick, galvanized Steel pipe

2 inch in diameter, galvanized Steel strip 10mm thick with fixing

plates, anchors and anchor bolts…etc. Price to include excavation

and all concrete works 40x40x40cm, as per drawings and according

to engineer instructions.

No. 9

29 Supply, fill & spread 60cm depth of gravel size ranging from 2.0 to

15.0 cm in layers for the green area according to the drawings,

specifications and the engineer's instructions. The price includes the

excavation from natural ground levels to the required designed

levels & the excavated materials should be removed out from the

site to the approved places.

M2 130


SUBTOTAL OF (C) External Works

1 Bill No. (1) External Works

‐ SUB TOTAL


(D) provisional items works

Unit Rate Total

$ Amount $

Bill No. (1) Electricity Items

1‐Main Power Supply Components

1.1 Supply and install outdoor 250 KVA‐22/0.4KV transformer completed

with all other needed component Such as Lattice steel pole with base,

steel arms, fuse holder,36 Kv isolator , Low voltage main LTL switch, also

price include all needed M.V cables , With all needed civil works and

any other needed materials and workmanship to complete the job

according to GDECO design study drawings specifications and the

engineer’s instructions

LS 1

1.2 Enlargement of the existing power supply sub scription from 3x100A to

3x400A with tacking in consideration Removing the old existing WH

meter,and rearrange the panel , according to GDECO regulation with

complete needed feesLS 1

2‐Stage Lighting System

Supply and install the following items according to the drawings,

specifications and the engineer's instructions:

‐the cost of all ducts required should be charged within concrete and

block works

1.3

Stage lighting system

(optional item –1)

‐ 500 W Fresnel spot lights as (SFR) of FURSE or equivalent.No. 4

1.4 650 W Fresnel spot lights as (JER/TH) of FURSE or equivalent. No. 4

1.5 1000W Fresnel spot lights as (MFR/TH) of FURSE or equivalent. No. 6

1.6 500W profile spot lights as (SPR/TH) of FURSE or equivalent. No. 4

1.7 650W profile spot lights as (SPR/TH) of FURSE or equivalent. No. 4

1.8 1000 profile spot lights as (MPR/TH) of FURSE or equivalent. No. 6

1.950 mm diameter aluminum spot bars complete with all accessories

needed as cat No.30. 1B. 12 of FURSE or equivalent. RM 50

1.10

Stage lighting system

(optional item –2)

Supply, install, connect & commission stage lighting as follows:

3. Variable Beam Angle profile spot light

‐ 1000/1200 Z 00 TWW of CCT Lighting

No. 3

1.11 1000/1200 Z 00TX of CCT Lighting. No. 3

1.12 2000/1200 Z0 DWW of CCT Lighting No. 3

1.134. Starlette Fresnel projectors:

‐ 1000/1200 Z0050Fresnel of CCT LightingNo. 3

1.14 2000 Z0080 Fresnel of CCT Lighting. No. 3

1.155. Condenser Variable bean profile:

‐ 650 Z0602 minute of CCT Lighting.No. 5

1.16 650 0603 minute of CCT Lighting No. 5

1.17 500/650 0608 minute of CCT Lighting. No. 5

1.18 6. Spot bars of (CCT Lighting) MR 50

1.19 7. Connector Box (of CCT Lighting) No. 4

1.20 8. load Sockets of (CCT Lighting) No. 30

1.21

9. Starlette Fresnel projectors

‐ 1000/1200 Z0050Fresnel of CCT Lighting No. 6

Item

Description

Unit Qty.


(D) provisional items works

Unit Rate Total

$ Amount $Item

Description

Unit Qty.

System Video Conference

1.22

System Video Conference

‐Pcs‐1p

Quantity:1

‐ ISDN MCU software (MB Memory Stick) PCS‐320M1

Quantity:1

‐ Wired Microphone for PCS‐1PVC SYSTEM‐PCS‐A1

Quantity:1

‐6 BRI ISDN UNIT FOR PCS‐IP VC SYSTEM‐PCS‐B384

Quantity:1

‐ DATA SOLUTION BOX/PCS‐DSB1

Quantity:1

‐ Microphone Mc – 906

Quantity:1

No. 1

1.23

Supply, install, connect & commission

Video projection system complete with wires, cables, conduits, boxes

and all accessories as shown in the drawings and specifications 650W

profile spot lights as (SPR/TH) of FURSE or equivalent.No. 4

1.24

. XGA data video projector as per specifications.

Quantity:1

. Video cassette player recorder. Quantity:1

. Motorized large screen. Quantity:1

. Wiring network.

Quantity:1

. Installation & system functioning.

Quantity:1

. Total value of equipment.

Quantity:1

LS 1


‐ SUB TOTAL of (D) provisional items works


Total Amount

( $ )

Construction Works : ( A) M.P.H Building

Construction Works : ( B) Labs Building

Construction Works : ( C) External Works

Construction Works : ( D) provisional items Works

Grand total of the school works

Title: ………………………………………..……………………..………………………….………….

Telephone:………………………………………………………………………………………..…….

Fax: ……………………………………………………………………………………………...……….

Mobile: …………………………………………………….…..………………………………..……….

Lot 2: Rehabilitation Works for the Rosary Sisters School

General Summary

Item Description

Total in numbers: ........................................................................................................................

Total in letters: .............................................................................................................................

Name of the contractor: ………….………..……………………………………………………......

Authorized signature: ……………...………………….………………………………………...…..

Signature and Sealing:…………………………………………………...…………………….…….

Page 43 of 43 Contractor Signature Stamp

Date post:	22-Mar-2022
Category:	Documents
Upload:	others
View:	3 times
Download:	0 times

Multipurpose Hall Building A - Procurement Notices

Documents