N Series
KEY FEATURESDual SRS AirbagsCruise ControlAudio Control on SteeringABS Equipped
KEY SPECIFICATIONSModel HFC1048 K/HFC1068K/HFC1061KGVM 5000/6800/8800Engine Cummins ISF EngineType Diesel, 4 cylinder in-line, water cooled, common rail + SCRTransmission German ZFType ZF5S400
ENGINEHFC1048K / HFC1068K
HFC1061K
Model Cummins ISF2.8S5 Cummins ISF3.8S5
Max output (PS/rpm) 148/2,900 148/2,600
Max torque (Nm/rpm)) 360/1,500 450/1,700
Maximum engine speed 101 110
Type Diesel, 4-cylinder in-line, Water cooled, Common Rail + SCR
Bore & stroke (mm) 94 x 100 102 x 115
Piston displacement (cc) 2,776 3,760
Fuel injection system Electronic control common-rail injection system
Ait intake system Turbocharged and Intercooled
Air cleaner Paper element type with cyclone
Fan clutch ф 310 dry sin-gle-disk diaphragm
spring clutch
ф 320 dry single-disk diaphragm spring
clutch
Emission control system Euro V Euro V
AXLE LOAD & TYRE LOAD LIMITS
HFC1048K / HFC1068K
HFC1061K
Front axle Forged steel piece, I -section
Rear axle Full floating pressed steel banjo-type housing
Final gear ratio 5.571 4.3
WHEEL & TYRESHFC1048K / HFC1068K
HFC1061K
Wheel type Radial ply
Wheel & rim size Single piece rim with tubeless tyres
6K X 16 offset 217mm,
ECE Standard
Pressed steel drum type,2. pieces,interim rim,17.5 x 6.00 offset
212mm,ECE standard
Number of tyres 7.50R16 (Front & Rear)
215/75R17.5 (Front & Rear)
Spare tyre carrier One sparewheel/tire with wind-up carrierBRAKESHFC1048K / HFC1068K
HFC1061K
Service brake Dual circuit Hyraulic brake
Control Dual circuit Hyraulic brake
Full air brake, quad circuit with air dryer.
Air tank with auto release valve
Front disc diameter The diameter of leading trailing shoe is ф320,the width of shoe is 100
Rear disc diameter The diameter of leading trailing shoe is ф320,the width of shoe is 100
Anti-lock system (ABS) YES
Auxiliary brake Exhaust brake
Parking brake Rear drum parking brake
Spring-accumulated parking brake
PERFORMANCEHFC1048K / HFC1068K
HFC1061K
Turning radius (m) 7 7.5
Engine RPM @ 100km/h 3200 2950
Maximum speed (km/h) 101 110
TRANSMISSIONHFC1048K / HFC1068K
HFC1061K
Model ZF5S400 LC6T55
Type 5MT 6MT
Gear ratio 1st: 5.0152nd : 2.5433rd: 1.5364th: 1.0005th: 0.789Rev: 4.481
1st: 6.4822nd : 3.6543rd: 2.2634th: 1.4775th: 1.0006th: 0.770 Rev: 5.996
N SERIESENGINE & DRIVELINE SPECIFICATIONS
N SERIESFEATURES
About Cummins Engine ISF• Exceptional performance and low operating costs• Reliable and durability• Key environmental benefits includes low noise and low emissions capability• Feature: Modular design for single side servicing and easy access• Feature: High Pressure common rails system for optimized combustion
About Selective Catalytic Reduction (SCR)• Cummins is the only diesel design manufacturer with in-house design integration of all the critical subsystem from air handling to exhaust after treatment.• The entire Cummins SCR system is centrally controlled and monitored by the electronic control module.• Feature: SCR is an exhaust treatment system which coverts NOx in the exhaust stream into harmless gases• Feature: Allows optimization of combustion allowing improved fuel economy and reduce heat built up.• DEF also known as Adblue is generally 4%-8% of normal diesel fuel consumption depending on vehicle operation and application.
About ZF 5S400 Transmission• Global leader in driveline and chassis technology• Feature: Transmission is light built yet still manages high performance. Benefits long service life and quiet running.• Feature: Excellent gear change due to state of the art synchronizer pack.
Dual SRS airbags• Enhanced Safety for Driver and Passenger as well• Improved Protection against accidents
Cruise Control• Ease of operation • Less fatigue while driving
Audio Control on Steering• Ease of operation • Additional safety for drivers to operate channels
N SERIESDIMENSIONS
DISCLAIMER
WARRANTY
MODELS HFC1068K HFC1048K HFC1061K
GVM (kg) 6800 4800 8800
Wheelbase (WB) 3320 3320 3845
OL (mm) 6012 6012 7030
OW (mm) 2096 2096 2300
OH (mm) 2300 2300 2350
FOH (mm) 1012 1012 1125
ROH (mm) 1680 1680 2060
FT (mm) 1680 1680 1665
RT (mm) 1650 1650 1525
GC (mm) 187 187 227
TR (M) 7 7 7.5
Tire Size
Front 7.50R16 7.50R16 215 / 75R17.5
Rear 7.50R16 (D) 7.50R16 (D) 215 / 75R17.5 (D)
Important Notice: JAC Trucks are distributed in Singapore by Metaquip TC Industrial Pte Ltd All efforts have been made to ensure the information contained in this brochure was correct at the time of printing. Metaquip TC Industrial Pte Ltd reserves the rights to alter any details of the specifications and equipment without notice. Please note that some options may only be applicable in combination of others.
New Vehicle Warranty Period
JAC N series model Standard WarrantyHFC1048K/1068K 3 Years or 100,000km whichever comes firstHFC1061K 3 Years or 100,000km whichever comes first
Battery warranty -12 months from date of delivery (pro-rated) Please note: warranty will be void if scheduled servicing is not done by Metquip TC Industrial Pte Ltd
METAQUIP TC INDUSTRIAL PTE LTD23 Jalan Buroh, Singapore 619479. Tel: 6265 3666 Fax: 6264 1666
Email: [email protected] www.metaquip.com
