Total No. of pages in tender document: 50 (fifty only) pages

TENDER FORM

NTR College of Veterinary Science

SRI VENKATESWARA VETERINARY UNIVERSITY

GANNAVARAM– 521102, KRISHNA DT.

SRI VENKATESWARA VETERINARY UNIVERSITY

NTR COLLEGE OF VETERINARY SCIENCE, GANNAVARAM

E-PROCUREMENT NOTICE

Tender Notice No. A3/17/NTRCVSC/2018-19 Date:22.10.2018

Tender ID on eprocurement website: 229200

E- Procurement tenders are invited from the manufacturers or their authorized dealers for

supply of various equipment to be installed at the College of Veterinary Science, Garividi,

Vizianagaram dt.

Details are as follows:-

1) Tender document online opening date 22.10.2018 at 4.30 PM

2) Tender document online closing date 06.11.2018 at 5 PM

3) Bid- Submission Online closing date 06.11.2018 at 5.30 PM4) Submission of all the uploaded documents (Hard

Copies) at the NTR College of Veterinary Science, Gannavaram

09.11.2018 before 4 PM

5) Bid online opening date at the NTR College of Veterinary Science, Gannavaram

After closure of bid submission online

Bidders shall have APTS Registration (for details log on to www.apts.gov.in)

For details visit www.apeprocurement.gov.in

For any clarification, please contact:

+91-9989051547

Sd/-Dr.G.Srinivasa Rao

Associate DeanNTR College of Veterinary Science

GANNAVARAM

GENERAL TERMS AND CONDITIONS

1

.

Tenders will be accepted through on-line up to 06.11.2018 until 5.30 PM by the

Associate Dean, NTR College of Veterinary Science, SVVU, Gannavaram for the supply

of various equipment as listed in Annexure A.

2

.

All the interested bidders have to mandatorily log on to e-procurement web site through

Secure mode only and submit their bids using digital certificates (signing certificate –

single key pair) obtained from Andhra Pradesh Technology Services Ltd. [APTS – Sub

CA] in-compliance to Chapter III of IT Act 2000. The details and procedure for

obtaining digital certificates is given at https://tenders.apeprocurement.gov.in.

3

.

The tenders are invited for the supply of certain equipment to different departments

located in the College of Veterinary Science, Garividi, Vizianagaram dt. as per the

specifications enclosed in Annexure-I.

ELIGIBILITY TO PARTICIPATE IN TENDERS

1. Manufacturers or their authorized Dealers are eligible to quote in this Tender. Authorized

Dealers should attach Letter of Authority from the Principal manufacturer to quote in this

Tender.

2. The Dealers/Makers should be registered firms and should have authorization certificate

from principals in case representation of the international firm.

3. The Tenderer shall supply good quality equipment as per Standards

4. The Associate Dean, NTR College of Veterinary Science, SVVU, Gannavaram reserves the

right to reject the tender of blacklisted companies and those of companies whose past

performance with the NTR College of Veterinary Science, SVVU, Gannavaram or College

of Veterinary Science, Garividi was unsatisfactory due to delayed / erratic supplies, frequent

product failures etc.,

SUBMISSION OF THE ON-LINE TENDER FORMS

1. Tenders have to be submitted in two parts in ONLINE in the prescribed proforma i.e.,

Technical Bid (Part. I) and Financial Bid (Part.II).

2. Financial Bids of those Tenderers who qualify in Technical Bid will only be considered for

finalization of the tender.

3. The Tenderer may please note that all the columns in the Technical Bid are to be filled in

meticulously with precision, with documentary evidence wherever necessary.

4. All the required documents / enclosures / literature / technical catalogs etc., have to be

uploaded & attached along with Technical Bid (Part. I of the Tender) only. Technical

catalogues for quoted equipment are essential. Tenders submitted without technical

literature of the equipment will be summarily rejected. Eligibility for Financial Bid (Part II

of the Tender) will depend on the outcome of documents uploaded / electronically attached

to Technical Bid.

THE SCHEDULES FOR OPENING OF TENDERS THROUGH ONLINE ARE:

PQ stage Opening of Technical Bids i.e. Part-I

Commercial stage Financial bid shall be opened after finalization of technical bid

1. The dates scheduled for RECEIPT and OPENING of tenders are fixed and will not be

changed under any circumstances. However, the Associate Dean, NTR College of

Veterinary Science, Gannavaram reserves the right of postponement of the date of opening

of Tenders or date of opening of financial bids in the event of any unforeseen reasons.

2. If for any unforeseen reasons, the last date for submission of tenders and opening of Tenders

happens to be a holiday, the notified dates automatically get postponed to next working day.

3. The Associate Dean, NTR College of Veterianry Science, Gannavaram is “Not Responsible”

for non-receipt of tenders or late uploading of tenders on online for any reason, whatsoever.

4. Failure to fill and sign the declaration and check slip shall make tender invalid.

DOCUMENTS TO BE ELECTRONICALLY ATTACHED:

1. All the documents are arranged in the serial order, (Serial Numbers and Page Numbers

should be indicated on the right side top of the corner) then uploaded to the

eprocurement web site i.e., https://tenders.apeprocurement.gov.in.

2. The

tenderers are requested to submit the following for verification on or before 09.11.2017 until

4 PM physically or by post. The NTR College of Veterinary Science is not responsible for

any postal delay.

a) Check slip of all the documents uploaded

Sl.No Code No. Name of the Document

1. E-I Declaration Form (Annexure II)

2. E- II Check List (Annexure III)

3. E- III Manufacturing License / Authorization letter from the

Manufacturing firm

4. E- IV Earnest Money Deposit

5. E- V VAT/Sales Tax/GST Clearance Certificate or payment

particulars for preceding two years along with

supporting Documents (2016-17 and 2017-18)

6. E- VI Annual Turnover Assessment order for the preceding

two years (2016-17 and 2017-18) certified by

Commercial Tax Officer / Chartered Account

7. E – VII Copies of balance Sheet, Profit and loss Account for

last two years i.e. (2016-17 and 2017-18) duly certified

by the Auditor

8. E-VIII Copy of GST registration certificate

9. E-X Users list for the item/ equipment during past 4 years

10. E- XI BIS / ISO/ CE issued by the Competent Authority

11. E- XII APSSIDC/NSIDC/MSME Certificate, if applicable

12. E-XIII Government Ownership Certificate, If applicable

13. E-XIII List of service centers with contact details for each

equipment

b) Copies of all the documents, which were uploaded

Note: This is only for cross verification of the uploaded documents. Any required document

failed to upload, the bid shall become invalid, even though documents are produced

physically.

3. All the enclosed documents shall be in English or Hindi or Telugu. If Any Document is

produced in any Language Other than English or Hindi or Telugu, True Translation copies

of such documents in English Shall be enclosed duly attested by a Gazetted Officer. Failure

to submit English translation of such documents shall make tender invalid. All Originals are

to be presented at the time of scrutiny for verification.

TRANSACTION FEE

All the participating bidders shall pay a transaction fee (non-refundable) to M/s APTS,

Hyderabad and through on line. (0.03% of estimate value + GST as applicable). It is mandatory

for all the participant bidders from 1stJanuary 2006 to pay a Non-refundable Transaction fee

electronically to the M.D., A.P.T.S, Hyderabad by the service provider through "Payment

Gateway Service on e-Procurement platform".

EARNEST MONEY DEPOSIT (EMD)

1. Earnest Money Deposit @ 3% in the form of crossed demand draft / pay order drawn on

any scheduled bank in favor of The Administrative Officer, NTR College of Veterinary

Science payable at Gannavaram, or online through e-procurement portal. The E.M.D. of

tenderers will be returned after signing the agreement with the successful tenderers.

2. All the bidders shall invariably upload the scanned copies of DD/pay order towards EMD

along with the bid, in e-procurement platform and this will be the primary requirement to

consider the bid responsive.

3. The DD/pay order should be deposited to this office while producing hard copies for

verification.

4. Cheques, Cash deposits, Term Deposits or Fixed Deposits will not be accepted towards

Earnest Money Deposit.

5. However the exemption of Earnest Money Deposit will be given to Small Scale Industrial

Units, Registered with the Government of Andhra Pradesh and the National Small Scale

Industries Development Corporation, New Delhi or the firms with specific exemption

orders issued by competent authority of Government of Andhra Pradesh or Government

of India. The order should be uploaded in the e-procurement platform in place of DD in

case of any such claim.

6. The items permitted by S.S.I. Registration Authority will only be considered for

manufacturing aspect only. IF ANY FIRM QUOTES ITEMS OTHER THAN THOSE

COVERED UNDER S.S.I. REGISTRATION, E.M.D. SHALL ACCOMPANY THE

TENDER. Failure to enclose E.M.D. shall make such of those items not covered under

S.S.I. Certificate invalid for consideration.

7. Earnest Money Deposit of other tenders deposited with this department during any period

of time shall not be considered for this tender

SECURITY DEPOSIT

1. The successful Tenders(s) shall within 7 days, after Associate Dean, College of

Veterinary Science, Garividi’s written notice of acceptance of the Tender has been posted

to him or them, deposit with the Associate Dean, College of Veterinary Science, Garividi

a sum of rupees @ 5% of the cost of the equipment inclusive of all taxes (or the authority

may fix the amount according to the value of the tender) as a security for the fulfillment

of the contract. Performance bond guarantee can also be considered, as security deposit.

The Earnest Money Deposit/Security Deposit shall carry no interest.

2. The Associate Dean, NTR College of Veterinary Science, Gannavaram reserves the right

to forfeit and confiscate Earnest Money Deposit, if the successful Tenderer(s) fail to pay

the Security Deposit which is required under the Terms and conditions of this Tender.

FORFEITURE / REFUND OF THE EARNEST MONEY DEPOST / SECURITY

DEPOSIT

1. In case the selected Tender(s) does not supply the stores at the quoted rates within the

period of contract and commits any breach of any one or more of these terms and

conditions, the Earnest Money deposited by Tenderer(s) will be forfeited by The

Associate Dean, NTR College of Veterinary Science, Gannavaram.

2. Earnest Money of the Tenderer(s) shall be refunded after signing the agreement with the

successful tenderers by the NTR College of Veterinary Science, Gannavaram. No

interest is payable by The Associate Dean, NTR College of Veterinary Science,

Gannavaram on such deposits.

3. The Security money deposited by successful Tenderer(s) shall be retained by The

Associate Dean, College of Veterinary Science, Garividi, till three months after the

expiry of the warranty period.

4. On due performance and satisfactory completion of the order in all respects during the

warranty period, the security deposit will be refunded to the Contractor(s) without any

interest within a period of 3 months with effect from the date of receipt of a request to

this effect from the supplier(s).

VAT/ SALES TAX/ GST CLEARANCE CERTIFICATE

Attested Photo Copy of VAT / Sales Tax/ GST Clearance Certificate and Sales Tax or GST

payment particulars obtained from the competent sales tax authority of the area concerned for

the last two years (2016-17 and 2017-18) shall be attached. Certificates older than that shall

not be considered. Those not liable for VAT/ Sales Tax/GST payment under relevant rules

should produce a certificate to that effect from the competent authority.

GST REGISTRATION

The firm should have valid GST registration number. Attested copy to this extent must be

submitted along with the technical bid.

MANUFACTURING LICENSE:

1. Attested Photocopy of the Latest Manufacturing License, which is in vogue shall be enclosed.

If the firm has applied for renewal of license, necessary authenticated proof from the

concerned Licensing Authority shall be furnished. Licenses issued for test and Analysis will

not be considered. The product/item quoted by the tenderer shall be underlined with “Red

Ink’. The License number and date should also be underlined with ‘Red Ink’. The abstract of

the product quoted should be enclosed. The Manufacturing License should clearly indicate a

minimum of two years of manufacturing and marketing experience. Items without the proof

of two years of Manufacturing and Market experience will summarily be rejected.

2. The tenders received without proper license, authenticated list of item covered by license and

authorization letters from actual / original manufacturers are liable for rejection without any

further notice.

3. Tenderers should enclose documents to show that manufacturing Unit has been recognized

with the ISO Certificate etc.

4. Tenderers should enclose documentary evidence of having manufactured and marketed the

product for two years.

BIS/ISO/CE etc CERTIFICATES (whichever is applicable):

1. Tenderer should produce BIS / ISO/ CE etc. certificate (wherever applicable) issued by the

concerned Licensing Authority.

2. Tenderers should enclose BIS / ISO Certificate for products wherever applicable.

3. The certificates whichever is applicable and claimed should be furnished with supportive

documents.

TERMS AND CONDITIONS FOR COMMERCIAL AGREEMENT:

1. The details of the required equipment are shown in e-procurement Web Application. Rates

should not vary with the quantum of orders or destination.

2. The rates quoted shall be in Indian Rupees only and must be expressed both in figures and

words as well. The rate of each category of equipment should be quoted. The rates quoted

should be inclusive of all the applicable taxes and “FOR destination” (destinations for the

equipment are mentioned in Annexure I). However, the applicable taxes and packaging costs

if any etc. should be clearly indicated in the price bid.

3. Tenderers who are supplying the items offered in this tender to other states shall enclose the

copies of latest invoices to support of their claim that the rates quoted to SVVU are

comparable.

4. No Insurance charges will be paid by the Department / Indenter.

5. The rates quoted by the tenderer shall not exceed the controlled rates, if the Government

controlled rates are in force on the date of submission of tenders. In the absence of controlled

prices, the tenderer shall quote reasonable price applicable to bulk purchases.

6. All rates quoted by the bidder should be valid for a period of One year from the date of

acceptance of the lowest Bid.

7. The rates offered in the tender shall not exceed the M.R.P. as well as the lowest price at which

the firm sells the product of identical description to any other department or organization or

person anywhere in the State / neighboring states of A.P. If such incidences of quoting higher

rates to this department come to the notice at any time, during the course of Rate Contract for

the rest of the Rate Contract period, the Associate Dean, NTR College of Veterinary Science,

Gannavaram reserves the right to initiate an appropriate disciplinary action against such firms

including black listing them.

8. IF ARTIFICIALLY LOW RATES ARE QUOTED, the ASSOCIATE DEAN, NTR

COLLEGE OF VETERINARY SCIENCE, GANNAVARAM RESERVES THE RIGHT TO

CROSS-VERIFY THEM AND IGNORE THEM FROM CONSIDERATION IN ORDER TO

PREVENT UNETHICAL TRADE PRACTICES.

9. Ordinarily, the tendered items will be selected based on the lowest rates quoted by the firms in

the Financial Bids. However, the tender committee reserves the right to select the product

even with higher rates depending upon the reported performance / market reputation / efficacy

of the item basing on the user reports / feedback given by the end users, ignoring the lowest

rates.

10. If tenderer quotes the rates at his will, overlooking the conditions in the previous paragraphs,

the tender is liable for cancellation even after approval of tender and firms will face suitable

legal action for such action at any time during the Rate Contract period.

11. Rates quoted should be marked clearly with main price and taken separately. Total price

after taking all the actuals will be taken as financial quote for comparison.

12. No representation towards upward revision of rates once accepted will be considered. DSIR

and other certificates for custom exemption will be provided by SVVU, Tirupati.

13. The Notification No. 45/2017-Central Tax (Rate) dated 14th November 2017 by the

Ministry of Finance, Govt. of India is applicable to the institute and hence the bidders

should keep this in mind while quoting GST rates.

14. The rate quoted and accepted will be binding on the tenderer for the stipulated period and on

no account will any increase in the price be entertained till the completion of tender period.

15. No tenderer shall be allowed at any time on any ground what so ever to claim revisions of or

modifications in the rates quoted by him. Clerical error, typographical etc., committed by

the Tenderers in the tender forms shall not be considered after opening of the tenders.

Conditions such as “SUBJECT TO AVAILABILITY” “SUPPLIES WILL BE MADE AS

AND WHEN SUPPLIES ARE RECEIVE” etc., will not be considered under any

circumstances and the tenders of those who have given such conditions shall be treated

incomplete and for that reason shall be summarily rejected.

16. No company / Firm which has been blacklisted either by the NTR College of Veterinary

Science, Gannavaram, A.P or SVVU or by any State Government or Central Government /

Organizations shall participate in the Tender during the period of Blacklisting. If any such

firm participates and came to know at a later stage, and if any firm is Black listed at a later

date either by the Government of Andhra Pradesh or any other State / Central Government

will not only be debarred / Black listed permanently and their security deposit /EMD

whichever is available with the Department will be forfeited and any business / transactions

will be stopped with their firms forthwith.

17. The indented stocks shall be delivered to respective departments (as indicated in the

Annexure I) in the College of Veterinary Science, Garividi at the cost of the supplier.

18. The rates should be quoted separately for each equipment.

AGREEMENT

1 Every successful tenderer on intimation by this office shall execute an agreement on Rs.100-

00 (Rupees One Hundred only) non-judicial stamp paper in the prescribed form, which will

be supplied along with the list of items tentatively approved. Agreement should be typed

only on one side of stamp paper with due attestation on each page.

2 In the event of failure to execute agreement in proper form along with the Security deposit

by successful tenderer within (10) days, the EMD of such tenderer will be forfeited and such

defaulters will forego the right to participate for future tenders for a minimum period of 3

years.

DEMONSTRATION OF THE EQUIPMENT:

1. The Tenderer may have to arrange for demonstration of the functioning of the equipment as

per specifications with the Associate Dean, College of Veterinary Science, Garividi, in case

of necessity.

2. If the equipment is declared to be not of standard quality or not meeting the specified

requirements, it will deem to be rejected. If any equipment supplied by the tenderer is used

after supply and is subsequently found to be not as per specifications, unsound, inferior in

quality or description or are otherwise faulty or unfit for use, then the cost of such equipment

will be recovered from the tenderer, if the payment had already been made, in addition to

penalty. The approved firms shall Re-Supply the equipment.

OTHER CONTRACTUAL OBLIGATIONS

1. The contract shall not be capable of being varied except by written consent by both the

Associate Dean (purchaser) and the supplier shall not in the absence of the specific written

acceptance be bound by any provisions of the supplier’s quotations, offers etc., which

purport to impose conditions at variance with this contract.

2. The supplier shall not sublet or delegate this contract or part thereof without the written

consent of the Associate Dean, NTR College of Veterinary Science, Gannavaram. Such

consent shall not however be withheld unreasonably. But the Tenderer(s) may without the

consent of The Associate Dean, NTR College of Veterinary Science, Gannavaram purchase

material as he/they does not normally manufacture.

3. The supplier shall keep confidential all matters concerning this contract and comply with all

reasonable security requirements. All drawing, blocks, specifications, manuscripts, samples

etc., supplied by the Associate Dean, NTR College of Veterinary Science, Gannavaram and

all copies thereof shall be returned to the Associate Dean when their use is terminated. In no

event the supplier(s) shall permit publicity concerning this contract without the prior consent

of the Associate Dean, NTR College of Veterinary Science, Gannavaram

4. Any undertaking or commitment given by or made by any Officer or the Associate Dean

verbally or in writing does not have any validity unless it is signed again by the authority

competent who concluded an agreement earlier.

INSPECTION AND PACKING

1. At all reasonable time during production and prior to dispatch of material the supplier(s)

shall afford and secure for the representative of the Associate Dean, NTR College of

Veterinary Science, Gannavaram every reasonable access and facility at his plant or

premises for its inspection and making of usual tests on behalf of the institute. The

supplier(s) shall advise the scheme at least 7 days prior to the time when any material is

ready for final inspection. The Associate Dean, NTR College of Veterinary Science,

Gannavaram will then make the inspection and subject to the material being in all respects

as specified and being of sound quality and workmanship the representative of the Associate

Dean, NTR College of Veterinary Science, Gannavaram shall sign or countersign a

certificate of inspection.

2. a) The supplier(s) shall supply to the Associate Dean, NTR College of Veterinary Science,

Gannavaram on request a report from time to time as to the progress of supplies. Any delay

or anticipated delay will be reported at once together with the full reasons there for.

b) The responsibility of procurement of transport facilities and dispatch of the stocks in good

condition and as per specifications and in time/door delivery lies with the supplier(s) and

they must keep up the delivery schedule at any rate.

c) The insurance should be done at the cost of supplier(s) as the rate quoted is all inclusive

for door delivery at respective institutes or research stations as indicated in Annexure I

3. Should the progress in supplies be delayed due to any cause beyond the reasonable control

of the supplier(s) and whether such delay or impediment occurs before or after the time for

dispatch, reasonable extension of time might be granted by agreement between the parties.

4. The supplier(s) shall insert in each case 3 copies of packing list, fully item wised to show

case number, contents and full description of the contents. The concerned department in

NTR College of Veterinary Science, Gannavaramat the receiving point will retain one copy

with him and return the other two copies, duly signed to the supplier(s) who will append one

copy of this packing list with invoices when sent to the concerned for payment.

SUPPLIES AS PER SPECIFICATIONS

1. All supplies shall be to the description and to the specifications laid down and in strict

accordance with the approved samples. Deviations, if any should be clearly brought out

failing which it will be normally construed that the materials offered are not to our

requirements. Any special features may also be clearly brought out.

2. The decision of The Associate Dean, NTR College of Veterinary Science, Gannavaram

however shall be final as to the quality of supplies received and binding upon the supplier(s)

in case, the supplier(s) supplies any other article than what is ordered such article supplied,

not being approved, shall be liable to be rejected.

3. If the Associate Dean, NTR College of Veterinary Science, Gannavaram requires any

changes in specifications the supplier(s) shall use his best endeavor to comply with The

Associate Dean, NTR College of Veterinary Science, Gannavaram’s wishes subject to fair

fixation of prices and delivery schedule where appropriate.

4. If at any time during the term of this contract, the plans of The Associate Dean, NTR

College of Veterinary Science, Gannavaram changes for any reasons The Associate Dean,

NTR College of Veterinary Science, Gannavaram shall have the right to terminate or alter

this contract by sending fifteen days notice to the supplier(s) by Registered letter. In respect

of such of the material as it complete and ready for dispatch within thirty days of such

notice, The Associate Dean, NTR College of Veterinary Science, Gannavaram agrees to

accept delivery thereof at the contract price and terms.

CONSEQUENCE OF NON-SUPPLY AND DAMAGES

1. All risks of loss, damage or depreciation to goods shall be upon the supplier(s) until the

material is delivered at the addresses specified and in accordance with the provisions of the

contract. Till the material received at the respective destination indicated by The Associate

Dean, NTR College of Veterinary Science, Gannavaram the property continues to be at the

risk of the supplier(s). The mere fact that the material is delivered to transporter is no

defense to the supplier(s) and the supplier(s) will be squarely held responsible for any

delayed receipt of the material by the College of Veterinary Science, Garividi or for loss of

damage of any kind to the material in transit.

2. Assuming that the supplier(s) fails to deliver any or all the materials covered by the contract,

Associate Dean, College of Veterinary Science, Garividi reserves the right in addition to

other legal remedies, to cancel the contract or any portion thereof and hold the supplier(s)

liable for all damages sustained by virtue of the supplier(s) failing to perform the contract

and consequent cancellation of the contract.

3. In the event of the supplier(s) failing to complete the supplies in time or according to the

approved specifications, Associate Dean, College of Veterinary Science, Garividi reserves

the right to make such arrangements as it may think fit for the completion of the supplies on

account of and the sole risk of the supplier(s).

4. In case the goods are not supplied according to specifications, they will be summarily

rejected.

5. The time allowed for delivery of goods shall be deemed to be the essence of contract. In

case the goods are not delivered to the respective addresses as indicated in the Annexure-I

within the stipulated period, the Associate Dean, College of Veterinary Science, Garividi

reserves the right to recover the liquidated damages a sum equal to 2 % of the contract price

of the undelivered material per week subject to a maximum of 5 % of the value of

undelivered material. The Associate Dean, College of Veterinary Science, Garividi also

reserves the right to cancel the purchase order in case supplies are delayed beyond the

scheduled date of delivery and to make such arrangements as he may think fit for the

completion of supplies on account and at the risk of the supplier(s). The additional expenses

thus incurred together with the consequential losses and also the liquidated damages shall be

recovered from the supplier(s) out of his/their security deposit/Earnest Money deposit and

any other amount due to him/them. The balance still if any payable by the supplier(s) shall

be paid by him/them within 7 days of notice by Associate Dean, College of Veterinary

Science, Garividi.

6. All invoices shall be prepared in four copies and shall be signed by the supplier(s) or

his/their authorized agent(s). Every invoice shall bear a certificate to the effect that the

material covered by the invoice(s) has been inspected by the supplier(s) before delivery and

confirm in every way to the contract specifications and is packed in accordance with the

contract requirements and further that the invoice is correct in every particular and no other

invoice has been rendered previously in respect of the articles charged in the particular

invoice. The invoice in triplicate along with advance stamped receipt shall be raised in the

name of The Associate Dean, College of Veterinary Science, Garividi.

7. The payment of the bills shall be made by the Associate Dean, College of Veterinary

Science, Garividi duly deducting the statutory deductions, if any.

PENALITIES

1 If the successful tenderer fails to execute the agreement and / or deposit the required security

deposit within the time specified or withdraws his tender after the intimation of the

acceptance of his tender has been sent to him or owing to any other reasons, he is unable to

undertake the contract, his contract will be cancelled and the Earnest Money Deposit

deposited by him along with his tender shall stand forfeited to the Associate Dean, College

of Veterinary Science, Garividi and he will also be liable for all damages sustained by the

Associate Dean, College of Veterinary Science, Garividi by reasons of breach, such as

failure to supply, including the liability to pay any difference between the prices accepted by

him and those ultimately paid for the procurement of the articles concerned. Such damages

shall be assessed by the Associate Dean, College of Veterinary Science, Garividi, whose

decision is final in the matter.

2 Non-performance of contract provisions will disqualify a firm to participate in the tender for

the next three years.

3 In the event of tendered supplies failing quality test, contract with the tenderer will be

suspended and purchases made from alternative suppliers. Such firms may be black listed

for three years beginning from the year following the one in which defective supplies were

detected. The tenderer shall also be liable for action under criminal law and the matter shall

be notified to the concerned Licensing Authority.

4 In all the above conditions, the decision of the ASSOCIATE DEAN, COLLEGE OF

VETERINARY SCIENCE, GARIVIDI shall be final and binding.

5 In the event of any dispute arising out of the tender such dispute would be subject to the

Jurisdiction of the Civil courts with in the city of Tirupati.

SETTLEMENT OF DISPUTES

1. Any difference or dispute arising out of or in connection with this tender or acceptance

thereof or the contract that may be entered in consequence thereof, shall be decided by

arbitration. The Associate Dean, College of Veterinary Science, Garividi or his nominee

shall be the sole arbitrator and the arbitrator’s decision shall be final and binding on the

parties. The Tenderer(s) will have no objection to such appointment on any ground

whatsoever including that such nominee, in his official capacity dealt with this matter at

any stage.

2. The parties hereby agree that in the event of any dispute no cause of action shall arise in

their favour to approach any court unless they have resorted to and exhausted the remedy

of arbitration as envisaged above.

3. The parties also do hereby agree that the contract envisaged by these terms and

conditions shall be deemed to have been entered into at Tirupati alone will have

jurisdiction to try and legal proceedings which may arise out of this contract. Neither

party shall file any proceedings in any other court

Sd/-Dr. G. Srinivasa Rao

Associate DeanNTR College of Veterinary Science

Gannavaram

ANNEXURE I

(Technical Specifications)

Sl. No. Name of the equipment

Specifications Qty.

GVDVMC001 Autoclave 1. Material: Stainless steel, mild steel2. Chamber volume (approx..): 100 lts.3. Insulation wall : double wall4. Automatic grade: Semi automatic5. Mount type: Floor mounted6. Temperature range : up to 131°C7. Pressure range: 10-20 psi8. Installation required9. Frequency :50/60 Hz10. Phase : Single11. Power consumption (KW): 6-24 KW12. Inner container is required13. Pressure gauze14. Out flow tap15. Locking system with locks16. Temp. and timer display17. Should have Water level indicator18. Onsite warranty 5 years

02

GVDVMC002 Hot-air Oven 1. Inner chamber is made of Highly Polished Stainless Steel.2. Outer chamber is made of Mild Steel Sheet duly pre-treated in seven tanks process for surface

treatment & are finished with durable Powder Coated Paint. 75 mm gap between the walls is filled with special grade glass wool for proper insulation and to avoid heat losses.

3. Inner chamber is fabricated with ribs to adjust shelves to any convenient height. Supplied with 3 removable shelves. Shelves are made of polished SS Sheet. Insulated door is fitted with heavy hinges with a special design spring – loaded door closing device.

4. Door gasket made of synthetic rubber compound instead of Asbestos.5. Heating elements are made of high grade imported Nichrome wire which are insulated inside

02

the porcelain beads and are generally placed suitably in Air Path for uniform temperature all over the space. Temperature is controlled by an electronic digital temperature controller-cum indicator, provided with air Circulating fan for providing homogenous temperature throughout the chamber with wide temperature 50°C to 250°C ovens for various applications.

6. Air ventilator ports provided on both sides at top to ventilate, gases and fumes if any.7. Control Panel: The equipment is provided with a panel having a digital temperature control

knob. ON/OFF switch, two pilot indication lights and provision for fixing the TIMER. Supplied with cord and plug. Suitable to operate on 220 V single phase, 50 Hz, AC supply.

8. Exterior Size (approx.): 800 x 1150 x 830 mm9. Inner Container Size (approx..): 600 x 650 x 600 mm10. S.S. (304 grade)11. Onsite warranty 5 years12. Supplied with suitable servo stabilizer

GVDVMC003 Seitz filter assembly including Seitz, vacuum pressure pumps etc.

1. Filtration assembly (Autoclavable) 250 ml to 500 ml capacity. Reusable bottle top filter can be screwed onto standard glass reagent bottle

2. Filtration flask material shall be non-toxic, compatible for cell culture media and serum filtration.

3. Shall be compatible to hold 0.22 μ and 0.46 / 0.47 μ filters with maximum flow rate and through put.

4. Appropriate lid5. Vacuum pump: Piston powered, oil free pump6. Power: 220 to 240 V/ 50 Hz7. Motor rotation: Minimum of 1400 RPM8. Horse Power: 1/8 HP9. Noise level: 50 dB10. Aluminium metal compact body11. Warranty on pump:5 years

01

GVDVMC004 Millipore filters 1. Colour: white or black2. Surface: plain or gridded3. Wettability: hydrophilic4. Sterilization: by autoclave (121 °C at 1 bar), EO5. Operating temperature: 75 °C max6. Protein binding: 150 µg/cm2

02

7. Bacterial endotoxins: 8.0 EU/mL8. Should include 1 pack of 0.22 micron compatible filter padsGravimetric extractables: < 1.0%

GVDVMC005 Students Microscopes with light source

1. Total Magnification: 40x – 1600 x,2. Eyepiece WF 10x, H 16x3. Objectives 4x,10x,40x, 100xoil SL ,4. Built in LED illumination With battery backup,5. Coarse & Fine Focusing system.6. Viewing Head : Monocular 45 deg inclined, tube, 360 deg Rotatable .7. Double layer mechanical Stage120x120mm Moving Range 60 x 30mm Condenser with

IRIS diaphragm & Filter. Fully Imported.8. Must be standard make. Not OEM.9. Warranty: 5 years

15

GVDVMC006 Stage and ocular micrometer (for measurement of bacteria)

Stage and ocular micrometers for measurement of bacteria, etc. for 10X, 40X, and 100X calculations

05

GVDVMC007 Platinum loops Platinum loops 05GVDVMC008 Bunsen burners

and platinum loops

Fast flame Bunsen burner Stainless Steel, for use with natural and cylinder gases, 15cms height, head diameter 13 mm, Nickel plated with stopcock.Should include platinum loops for bacterial cultures.

20

GVDVMC009 Mc’intosh and fields’s anaerobic jar

Mc’intosh and fields’s anaerobic jar; must be of stainless steel. 02

GVDVMC010 Incubator 1. Orbital shaking incubator2. Stackable orbital shaker incubator with two adjustable stationary shelves located above the

18” x 18” rotating platform. Gentle to vigorous agitation is accomplished with variable 15 to 500 rpm (+/- 1 rpm) speed control or 15 to 300 rpm when stacked.

3. The unit is controlled by a digital push-button controller. Speed will be displayed in rpm with an LED display. The shaker will rotate in an orbital fashion with an orbit of 0 .75 inches.

4. Chamber temperature is controlled by a PID microprocessor controller to an accuracy of +/- .1C at 37C in flask over a range of ambient +10C to 80C. The shaker will have a timer that operates from 0 .1 to 999 minutes, 0 .1 to 999 hours or continuously.

5. The shaker will have over temperature protection via an independent, hydraulic thermostat.

02

6. The unit will shut down when the chamber door is opened.7. All set points are retained by non-volatile memory, thus the shaker will automatically re-start

following power failure and after power is restored.8. Unit should operate in a 0 to 40C and 20 to 80% non-condensing humidity environment.

Physical Specifications:9. The unit should have a triple eccentric drive mechanism with a steel shaft in a cast iron

housing with six sets of permanently lubricated ball bearings and can accommodate a load capacity of up to 50 lbs.

10. The shaker should have a solid-state brushless DC motor. The shaker should accommodate an 18”x18” universal platform and shake various combinations of vessel clamps (flask holders, plate holders and test tube racks).

11. The platform and vessel clamps should be constructed out of stainless steel.12. An ABS control housing should surround a polyester control panel. The shaker exterior

should be constructed of cold-rolled, powder-coated steel and has dimensions of approximately 33”L x 27.5”W x 40.5”H.

13. The chamber should measure approximately 21”L x 22”W x 27”H and should have a 9 Watt, 550lumens, fluorescent bulb for easy sample viewing.

14. An electrical splash resistant outlet that can operate from –20C to 100C, inside the chamber to provide power for safe operation of shakers, stirrers or rotators.

15. Large viewing window built into the door measuring 19” W x 24” H which permits monitoring of samples for harvesting without disturbing the chamber atmosphere.

16. A dual tiered 18 x 18” platform can be mounted inside of the chamber doubling the vessel capacity of the shaker.

17. Onsite Warranty: 5 yers18. Suitable servo stabilizer

GVDVMC011 Biological Oxygen Demand (B.O.D.) Incubator

1. 20cu.ft.(Approximately) Refrigerated Incubator: ideal for BOD applications Advanced microprocessor controlled with easy-to-use push buttons and set-points Connection for external chart recorder and RS-232 interface for data logging

2. Holds more than 300 BOD bottles of 300ml3. Easy-to-clean, corrosion resistant construction4. Compressor relay for conservation of energy5. Microprocessor control with easy-to-read displays actual temperature within 0.1°C Push-

button controls feature temperature set-point selection

01

6. Forced air circulation to deliver excellent temperature stability7. CFC-free, foamed polyurethane insulation to prevent the heat loss8. RTD temperature probe and to protect set point and prevent accidental temperature change9. Door key lock protects samples from unauthorized access10. Temperature Range - -10°Cto+50°C Capacity – About 560 Liters Uniformity@37˚C -

±0.5°C11. Sensitivity@37˚C - ±0.1°C12. Shelves – Minimum of 6 Nos13. Temperature Control – Microprocessor based14. Display – LED Dimensions (WxHxD) : about 26.5”x57”x20”15. Onsite warranty: 5 years16. Suitable servo stabilizer

GVDVMC012 Water bath 1. High Precision water bath with strirrer. Very tightly controlled temperature with an accuracy of 0.10Cof digital temperature controller.

2. Inner chamber W H D 430 x 240x265mm

02

GVDVMC013 Deep-freezer -200 C

1. Vertical Freezer Capacity should be to accommodate about 24000 samples of 2ml tubes2. Programmable Temp. in increment of 1ºC even at room temp up to 32ºC3. The Capacity should be about 400 litter 4. Low Power consumption: approx 8.7 Kwh per day5. Highly efficient vacuum insulation panels with use of traditional urethane insulating foam to

reduce the thickness of outer walls and provide energy saving6. Pull down time 5.3 hours7. System should be single door with minimum 5 compartments with doors for each

compartment.8. The freezer must have Heated air Vent to prevent ice formation with Spring-Assisted plunger

to remove vacuum for easy opening.9. The system should have Non- Volatile memory & Auto re-start and Battery Backup for the

display10. The system must come with password protection for temp. & alarm set-points11. CFC Free and HCFC free refrigerants with biodegradable Polyolester oil compressor.12. High efficiency freezers use high efficiency vacuum insulation panels in addition to a think

polyurethane, providing a full 130 mm thick layer for superb insulating efficiency.13. Heated air Vent with plunger to break icing and prevents vacuum formation

01

14. Battery Backup for the display, activates alarms and displays temperature during power outages.

15. Lockable security plates16. Five Compartments with four adjustable height SS shelves17. Door latch with Positive, single-handed cam action latch with lock18. Shall provide suitable servo voltage stabilizer.19. Shall provide ambient temperature facility for functioning of the deep freezer.Onsite warranty for 5 years from date of installation.

GVDVMC014 Photo Colorimeter

1. Display: Seven segment LED Display2. Mode Selection: ph Mode, Standby Mode, mV Mode3. Wavelength Range: 400nm, 420nm, 480nm, 520nm, 540nm, 580nm, 620nm 680nm4. Transmission: N/A5. Absorbance: 0-1.99 abs6. Filters: Best Quality Glass Filters7. Bandwidth: 15 – 20nm8. Repeatability: 0.01 abs9. Accuracy: -0.01 to +0.01 abs10. Sample Holder: Cuvette Round 9mm11. Power: 230V Ac @ 50Hz12. Warranty: 5 years on siteStandard Accessories: 5 Cuvettes and Instruction Manual

02

GVDVMC015 Ultra-violet Lamp

3 feet length UV lamp full set of reputed brand 02

GVDVMC016 Laminar flow cabinet

GENERAL Cabinet should be certified - NSF 49 (2007) Class II (Laminar Flow) AND UNDERWRITER’S LABORATORY (UL) UL Standard 61010-1DESIGN AND PERFORMANCE CRITERIAProvide biological safety cabinets with workspace for testing and experimentation of low to moderate risk agents in the Classes and Types indicated, as defined by NSF International NSF/ANSI 49. Class II cabinets shall provide protection of experiment from ambient environment and protection of ambient environment from experiment. Biological safety cabinets shall operate in an efficient and sustainable manner.Electrical consumption of new units shall be no greater than 200 watts nominal width 4 ft unit.Cabinet Nominal 4 ft width - 61.8”H x 51.2”W x 31.5”D (1568mm H x 1300mm W

02

x800mm D)Cabinet shall be an NSF Listed and Approved Class II biological safety cabinet.Cabinet should include an Adjustable Stand, UV Light, set of Arm rests as apackage.CONSTRUCTIONA. Cabinet shell shall use steel no less than 19 gauge (0.0394” thick) and validated to meet the NSF performance specification where top front edge shall not move forward more than 0.063 inches (1.6 mm) from the static position when a 250 lb (110kg) lateral force is applied to the top rear edge and the top of the sides shall not move forward more than the same amount when the same force is applied to the top of the opposite side.B. Unit shall have all metal plenums designed for easy removal at filter change.(Non-metal, fabric type plenums are not acceptable.)C. To facilitate cleaning, the interior sides and rear wall of the work area shall be of one piece no less than 19 gauge (0.0394” thick) Type 304 stainless steel construction with No. 4 finish. The joins between the side and rear interior walls shall have coved corners of no smaller than 0.406” radii.D. An efficient means of adjusting the down flow and inflow separately shall be provided. Additional penetrations of the shell of the cabinet should be avoided.E. Corrosion resistant ball valve for drain from trough beneath the work surface.F. Externally mounted fluorescent lighting fixture.G. One supply and one exhaust, scan-tested, zero-probe HEPA filter, 99.995% percent efficient on most penetrating particle size (H14 per EN 1822), serviceable and removable from front of unit.H. Two duplex receptacles, GFI protected with total load capacity of at least 5 amps.I. Single power cord 12 ft in length with a NEMA plug 5-15P.J. Corrosion resistant diffuser below the down flow filter.K. Protective screen to prevent foreign objects from being drawn into fans.L. A minimum of six media valves (at least three on each side, for vacuum or other) available on the cabinet.M. A minimum of two replaceable 3 inch cable/tubing ports (at least one on each side)PERFORMANCE REQUIREMENTSShould have dual motors for independent control over inflow and down flowvelocities.

The Dual motors should operate on DC saving energy consumption and emit lesser heat (around 15kw at 25Deg C ambient) in the area.A. Work access opening inflow velocity: Acceptable operating range 100 – 110 fpm.B. Inflow compensation controlling inflow velocity with 3% of set value with 100% increase in filter loading.Visual indicator on the front panel for the following features:1. Compensation reserve capability.2. Hours of operation3. Inflow velocity display (feet per minute)4. Downflow velocity display (feet per minute)5. Night Set-Back mode6. UV on7. Receptacles on8. Operating speed airflow9. Front window positionD. No HEPA filter leakage _ 0.01% of upstream concentration.E. Downflow velocity ± 5 fpm of NSF/ANSI validated nominal value.F. All downflow measurements within 20% of average.G. Separate down flow and inflow velocity flow alarms to signal overall variation greater than 20% from set values.I. Reduced flow or Night Set-Back mode allowing reduction in airflow and energy consumption while maintaining cleanliness and containment when not in operation.OPERATION REQUIREMENTSAvailable UV disinfection cycle. Adjustable UV exposure time saved in memory to facilitate consistent operationSafety interlock to prevent UV illumination when window is openThe final price should include ducting and all accessories requiredShould include suitable servo stabilizerOnsite warranty: 5 years

GVDVMC017 Colony Counter 1. Automatic weight compensation of Petri plates2. Anti-shock counting technology3. Ring light technology enables even illumination of the counting field4. Possibility of working with bright or dark background

02

5. Mean value calculation function6. Standard marker (Optional marker for external counting)7. Petri plates adapters (diameter < 120mm) Removable Wolfhuegel scale plate Adjustable

push force8. Sound and visual counting control Adjustable position of the magnifying glass 9. Warranty 5Years

GVDVMC018 ELISA test reader

1. Shall be operated in Visible and UV range.2. System shall able to read 96 well & 384 well Microplate and cuvette12.5 (W) x 12.5 (D) x

40-58 (H) mm (standard cuvette as well as low volume cuvettes of any pathlength) for the applications Enzyme assays, Immunoassays, Protein assays, Cell proliferation and cytotoxicity assays, DNA or RNA quantitation, Apoptosis assays, Kinetic assays, GPCR assays, Monochromator wavelength selection with xenon flash lamp a light source.

3. Wave length range from 200 to 1000 nm with 1 nm steps.4. Shall have inbuilt incubation and linear shaking of the microplate.5. Measurement speed for plates 6 s with 96-well plate,10 s with 384-well plate Linearity at

450 nm; for 96 well plate, 0 - 2.5 Abs, 2% for cuvette, 0 - 2.5 Abs, 2% (beam window ≥2 mm) Accuracy for plates and cuvette at 450 nm;1.0% + 0.003 Abs (0 - 2.0 Abs) 2.0% (2.0 - 2.5 Abs) Precision at 450 nm: Precision mode for both plates and cuvette, SD < 0.003 Abs or CV < 0.5% Spectral scanning; 200 to 1000 nm with 1 nm steps Incubation temp range for plates/cuvette; From ambient + 2° to 45°C USB connections: Personal Computer/ Memory device port for data export/ External printer.

6. An external printer shall be provided to take printout of the readings.7. System should able to run in both stand-alone mode and with computer & software

controlled.8. The instrument should have a memory of about 100 inbuilt protocols in stand-alone mode

and color display for better visualization.9. System should have self-diagnostics option to give a guaranteed high quality data. System

should have Power Save function for reduced energy consumption when the instrument is ‘on’ but not in use. Compatible cuvettes 2 pairs should work at power supply at 100-240 volts (50/60 Hz) Online 3 KVA UPS with 2 hr back up shall be provided with the ELISA reader.

01

GVDVMC019 Immuno electrophoresis apparatus

1. Electrophoresis tank of Midi Size to keep the antigen-antibody loaded slide2. Dimensions: 18 cm (L) x 16 cm (B) x 8 cm(H)

02

3. No. of slides: Minimum five of 7.5 x 2.5 cm4. Buffer volume: About 200 ml5. Basic unit with platinum electrode6. Gel punch single well (1 No.) Trough cutter (1No.)7. Template: 3 Nos.8. Power card 1 set with lid

Power pack:9. 300V maximum voltage, 700mA maximum current, 150W maximum power,10. Four pairs of outlet terminals, Timer with alarm function, Constant voltage or constant

current operation, Advanced safety device design, Compact size.11. Output Voltage / Inc : 2 - 300V / 1V12. Output Current / Inc : 1 - 700mA / 1mA13. Output Power : 150W14. Output : Constant voltage or constant current15. Control : Microprocessor controller16. Terminal Pairs : 4 Pairs17. Timer : 1~999 minutes with alarm, continuous18. Pause Function should be present19. Safety Device : No load detection; Leakage detection Sudden load20. change detection Over temperature protection Over load detection21. Crossover should be present22. Operation Temperature : Ambient to 40゜C23. Unit Dimension : Appr. 190x 305x 95mm (W x L x H )24. Rated Voltage : 100 - 240V

GVDVMC020 Centrifuge ordinary

1. Table Top, AC, 50HZ, with swing out rotor, adapters 4 Nos , to hold universal containers; and hermetically sealed caps 4 Nos, with windshield, and ‘o’ ring for full aerosol containment, safety interlocked lid, bio-safety features incorporated.

2. Max. Speed: 6,000rpm3. Max. RCF: 6,240 x g4. Max. Capacity: 4 x 400 ml5. Run Time: 1– 99 mins, Continuous operation6. Voltage: 230 V, 50 Hz,7. Programme Memory: Values last entered remain in memory. Data saved if power is

02

interrupted, 1.0 non-refrigerated, maximum capacity 4 x 400 ml to hold McCartney bottles (universal containers).

8. Other Technical details9. SWING-OUT ROTOR: 1 No.10. Max. Speed: 4,000rpm11. Max. RCF: 3,345 x g12. Max. Capacity: 4 x 400 ml13. Round Bucket 400ml for adapter inclusive of14. Polypropylene bottle 4 Nos. Sealing cap for round bucket: 4 Nos15. Each 400ml adapter should hold at least 4 McCartney bottles (universal containers) of sizelength 82 mm, diameter of the bottom 28.2 mm, volume 28 ml. Adaptor: 4 x50 ml: 4 Nos

GVDVMC021 Refrigerated Centrifuge

1. Multipurpose refrigerated centrifuge2. Control interface with numeric input buttons for setting and editing the running conditions3. Pulse key function for quick spin4. Fixed angle rotor RPM should be at least 15000rpm or 25910g5. Swingout rotor RPM should be at least 5000rpm or 5394g6. Fixed angle rotor should have at least 6X (250 and 15ml capacity) and 30X 1.5/2.0ml

slots7. Swing out rotor should have at least 4X 750ml capacity or 80X 15 ml capacity8. Temperature range should include -10 to 40 degrees9. Fast cool option should be there10. Automatic rotor identification option should be included11. Imbalance cut off option, safety lid lock option, lid drop protection options should be

included. 12. Should include fixed angle 8X50 ml rotor with 50ml and 15 ml adapters, fixed angle

12X15ml conical rotor, fixed angle 30x1.5/2.0ml rotor.13. Should include swingout rotors for 15 ml and 50ml tubes and 96 well plates14. Should be supplied with suitable servo stabilizerShould include 5 year on site warranty

01

GVDVMC022 Dental drill 1. Speed: High speed2. Type: Air- driven and electric3. Bur material: Tungsten4. RPM: 50000

04

5. Application: egg inoculationGVDVMC023 Automatic

pipette washer1. Shall be made up of PP or HDPE material.2. Works on siphoning principal. Proper inlet and out let.3. Shall accommodate 1 ml, 2 ml, 5 ml and 10 ml pipettes.4. Shall accommodate pipettes of length of more than 35 cm.5. Shall be supplied with inlet and outlet tubing.6. Shall consists of pipette jar, basket, washer-rinser

02

GVDVMC024 Egg Candler 1. LED : 10 Watt2. Max Output (Luminous Flux): 1000 Lumens3. LED life : 50,000 hours4. Battery : Lithium ion battery, 4400mA5. Battery Run time : 180 minutes (100% brightness6. Battery lifespan : Rechargeable 500-800 time7. Power supply : 110-230 V

02

GVDVMC025 Egg Incubator 1. Egg Capacity (chicken)(pcs): 2202. Voltage: 220V-240V AC 50/60 HZ3. Power(W): 150W4. Dimension(L*W*H): 53.5*56*76.5cm5. Weight: 40kg6. Feature: fully automatic

ONSITE WARRANTY 5 years

01

GVDVMC026 Inverted Microscope

1. Head: 45° Inclined Compensation Free Trinocular Head2. Eyepiece: WH10X/20mm and WH25X extreme widefield3. Objective: long working distance Plan (LWDPL), 4X/0.1 W.D .25mm, 10X/0.25 Phase

Contrast W.D .11mm, LWDPL20X, 20X/0.4 Phase Contrast W.D .6mm, and 40X/0.6W.D. 3.8mm

4. Interpupillary Distance: 2"-3" (50mm-75mm)5. Mechanical Stage: two-layer; size: 9.53"x6.77" (242x172mm); traveling range: 4.53"x2.59"

(115x75mm)6. Central Stage: 4.33" (110mm) in diameter7. Condenser: NA 0.3 Abbe with iris diaphragm, working distance: 3" (75mm)8. Focus: coaxial coarse fine focusing system with tension control; fine focusing scale value

0.000079" (0.002mm)

01

9. Phase Contrast Sliding Plate: center of phase contrast ring plate adjustable10. Centering Telescope: included11. Filter: blue, green, yellow and froster glass12. Illumination: halogen bulb 12V/30W13. Power Supply: 110V/60Hz (please email for 220V/50Hz version)14. Should have attached 10MP camera, software and LED monitor for

visualization/demonstration15. 5 yrs warranty16. Should be of reputed brand, no OEM product should be quoted

GVDVMC027 Refrigerator Energy Efficiency :5 Star Rating

Capacity :345 LitersInstallation Type :Free-StandingForm Factor :Standard Double DoorSpecial Features :Inverter, ConvertibleColour :Elegant InoxVoltage :100 VoltsDefrost System :Frost FreeShelf Type :Toughened GlassMaterial :SteelTemp. 2 to 8 0CIt should be provided with suitable stabilizer, lower stand and Fridge handle cover and top cover (with pockets).

01

GVDVMC028 Haemocytometer chamber

For eukaryotic cell counting 04

GVDVMC029 Micropipette set Micropipette set should include 0.5-2 µl, 2-10 µl, 10-200 µl, 100-1000µl each 01GVDVMC030 Multichannel

micropipette Multichannel micropipette (10-300 µl)8-channel

01

GVDVMC031 Vortex Mixer Adjustable speed: 100 to 3,000 rpm, continuous and intermittent “touch-control” modes, 220-230 Volts, AC, 50HZ; Cup heads size: 25 mm dia. x 22 mm deep for mixing contents in McCartney bottles., Heavy cast-metal base and suction cup to assure stability, prevent “walking”.

01

GVDVMC032 Weighing Balance

Weighing Capacity range: 1gm.- 1 kg, Readability 0.1gm, Pan size 6” (approx.) dual pans of 01

Stainless Steel, mechanical, table top. Standard weights should be supplied along with the Analytical balanceShould have enclosed chamberOn site warranty: 5 years

GVDVMC033 Magnetic Stirrer 1. Magnetic stirrer with hot plate2. Maximum stirring speed-1200 rpm with stepless speed control and good speed stability3. Heating Capacity - 600W4. Hotplate Size -175mm dia.5. Supply – 220/240V,50Hz, A.C6. Hotplate-Should be chemically resistant to acid and alkali7. Top Plate Material – Stainless steel8. Stirring Unit – Should be enclosed so that corrosive fumes do not enter it.9. Controls for both hotplate and stirrer should be provided with suitable indicators.10. Necessary electrical cables should be provided.

Warranty – 5 years from the date of installation

01

GVDVMC034 Microcentrifuge 1. Table top type2. 6X 1.5/2.0 ml tubes with adapters for 0.5ml and 0.2ml tubes3. Should include interchangeable 8X0.2ml strips rotor4. Warranty for 3 years5. Safety lock11. On and off button

01

GVDVMC035 Blotting Apparatus

1. Dimension 15cm (L)x11.5cm(B)x12cm(H)2. Gel Holder Cassette 2 Nos.3. Buffer Volume 650ml4. Gel Size 8x7 cm (2 Gels)5. Connecting Cord Red and Black (Each One)6. No. of Platinum electrodes Positive and Negative (Each One)7. Fiber Pad 12 Nos.8. Foam Pad 12 Nos.9. Cooling Unit Mini 1 No.10. Buffer Chamber with Safety Lid 1 No.11. Application: western blotting6. Warranty: 2 yeras

01

GVDVMC036 Agarose Gel Electrophoresis unit with Power Supply

1. Electrophoresis tank with cover.2. Gel casting system3. 1 Piece of 105 x 83 mm Tray4. 2 Pieces of 50 x 83 mm Tray5. 1 Piece of Analytical Comb 1.0 mm thick6. Two parts of 8 teeth for mini gel and one of 17 teeth for wide gel7. 1 Piece of Analytical Comb 1.0mm thick8. Two parts of 6 teeth for mini gel and one of 13 teeth for wide gel9. Power Cord

01

GVDVMC037 Polyacrylamide Gel Electrophoresis unit with Power Supply

Apparatus dimensions(W x D x H)

32.5 x 15.0 x 38.5 cm (buffer tank EB)32.5 x 15.0 x 40.0 cm (buffer tank EBC)

Gel size (W x L) 19.4 x 18.5 cmGlass plate size (W x L) 21.0 x 20.0 cmNumber of gels 1 or 2Capacity max. 30 samples per gel (60 samples total)Typical sample volumes 18 µl to 2,340 µl per well (depending on gel thickness)Combs Thickness

(mm) Number of Wells Volume perWell (µl)

0.75 1 prep. + 2 marker lanes 2 x 30 and 9701

12 7019 MTP comp. 3225 3030 20

1.0 1 prep. + 2 marker lanes 2 x 45 and 1,3101

12 9519 MTP comp 4525 4030 29

1.5 1 prep. + 2 marker lanes 2 x 75 and 2,3401

12 16519 70

01

25 7030 52

Buffer volume max. 5,400 ml for electrophoresis (buffer tank EB and EBC)max. 6,100 ml for blotting (buffer tank EB and EBC)

Volume of the preparative well10.

GVDVMC038 Thermal cycler with UPS

Gradient1. Block with capacity of 96 x 0.2 ml, 8 tube strips and 96 well plates (skirted, semi-skirted or

non-skirted).2. Technology to minimize the sample evaporation is preferable3. The sample is to be protected against heat transfer during the initial heating to avoid mis

priming and non specific amplification4. Gradient block with selectable temperature gradient in the temperature range of 30-990C5. Gradient should be available in 12 wells across the block.6. Programming of gradient function, adjustable ramp rate, time and temperature increment,

incubation mode, link function, pause function.7. Option for auto restart in the event of power failure.8. Variable Ramp rate of heating up to 6º C/Sec and cooling 5º C/Sec or better with silver block9. Temp. Control range: 4º to 99.9 º C and a gradient range of up to 24ºC.10. Thermal Accuracy: ± 0.3º C.11. Thermal Uniformity should be ±0.3º C 12. Provision for storing user methods

Other requirements:13. Provide suitable online UPS with minimum of three hour power backup.14. System should be licensed and authorized for PCR Application15. Comprehensive 5 years warranty + 2 years free AMC

Prompt after sale service should be available

01

GVDVPP001 Binocular microscopes

1. Total Magnification: 40-1600X Viewing Head: Compensation free Binocular Side top Head inclined at 30 rotatable, Antimould 360o. Eyepiece: WF10X /20mm, P16X pair. Quadruple Nose Piece.

2. Semi plan Achromatic Objective 4X, 10X, 40X(SL), 100X (SL) oil.3. Double layer Mechanical Stage 140 x 140 mm / 75 x 50mm.4. Coaxial Coarse & fine focusing adjustment system, Moving range 23mm, fine division

20

0.002mm.Abbe type 9 eproduci NA 1.25 with IRIS Diaphragm & Filter.5. Built in Illumination Halogen lamp 6V 20W brightness Adjustable Intensity controller.6. Focusing lock: Focusing lock is provided with the coarse focusing Knob. It is used to arrest

the Upward movement of the Stage so as to eradicate the Damage of slide and Objective Lenses. Optional attachments: Drawing attachment with eye piece set or multi viewers

7. Should be of reputed make. No OEM product should be quoted.Warranty: 2yeras

GVDVPP002 Rotary microtome, with thin sectioning facility

1. The advance and vertical stroke mechanisms run on cross roller guides that are free from backlash and maintenance-free. Both mechanisms as well as the coarse feed system are protected by a dust-proof plastic housing.

2. The handwheel can be locked in the 12 o’clock position via the handwheel handle. In addition, a handwheel brake mechanism allows you to lock the handwheel in any position via a locking lever integrated into the base plate.

3. Sectioning is done manually by rotating the exceptionally smooth-running, counterbalanced handwheel.

4. The coarse feed function is operated via the coarse feed wheel on the left side of the instrument housing.

5. Section thickness is selected via a turning control knob and indicated in the small window integrated into the instrument housing. Section thickness settings from 0.5 to 60 µm can be selected.

6. Both models are equipped with a slot cover preventing section waste from entering the interior of the instrument.

7. A mechanical trimming function, activated via a lever and featuring 10 µm and 50 µm trimming thickness.

8. Specimen retraction, designed to protect both knife and specimen.9. During the return stroke, the specimen is pulled back from the knife by 220 µm.10. Prior to the next section, the specimen advances by the selected section thickness plus the

retraction value.11. Operating temperature range: +10 °C to +40 °C12. Section thickness setting range: 0.5 - 60 µm Section thickness selection: from 0 - 2 µm in

0.5-µm steps from 2 - 10 µm in 1-µm steps from 10 - 20 µm in 2-µm steps from 20 - 60 µm in 5-µm steps

13. Total horizontal specimen feed: 25 mm

01

14. Vertical specimen stroke: 59 mm15. Specimen retraction (RM2125 RT only): 220 µm16. Dimensions and weight Width 400 mm Depth 470 mm Height 295 mm17. Working height (knife edge) 105 mm18. Weight (without accessories) 29 kg19. Optional features and optional accessories Specimen orientation (optional) horizontal: 8 °

vertical: 8 ° Rotability: ± 90 °20. Trimming thickness (RM2125 RT only): 10 µm, 50 µm21. Knife holder base with lateral displacement feature: north-south: ± 25 mm east-west: ± 20

mm Knife holder base without lateral displacement feature: north-south: ± 25 mm22. Should include suitable microtome knife and knife sharpener23. Onsite warranty: 5 years

GVDVPP003 Paraffin flotation bath

1. Paraffin embedding center to work on 230 V2. Capacities: Paraffin reservoir 3l, Cassette bath:approx.100 cassettes,3. Cassette tray:8 cassettes, Cold plate:70 cassettes4. Temperatures: Paraffin reservoir, mold warmer and cassette bath at 55 to 65ºC and cold plate

and cold spot at -5ºC5. Should include L’moulds and blocks or (for embedding)or Tissue capsules that are made up

of stainless steel, Perforated on the top and bottom for easy fluid circulation. should be partitioned for up to 4 sections. And dimensions shouldbe 37 mm (I.D.) x 6 mm (deep) (1-7/16" x 3/16").A secure positive snap-on cover.

02

GVDVPP004 Hot air oven 1. Hot air ovens (memmert heater) are sturdy double walled units, inner chamber made of S. S. And outer made of mild steel with power coating.

2. Gap between the walls fitted with glass wool insulation to avoid heat loses.3. Heating elements are made of high grade chrome plated microme wire. temp. Is controlled

by thermostat. Temp. Range 50 c to 250 c and accuracy : +- 2 c.4. Air ventilations are placed on top of both sides to remove hot gases / fumes.5. In memmert type units heaters placed at the right and left side of the inner chamber. All the

control switches & pilot lamps are fitted on the front panel. Trays should be supplied with G. I. wire mesh.

6. Inner chamber is made of Highly Polished Stainless Steel. Outer chamber is made of Mild Steel Sheet duly pre-treated in seven tanks process for surface treatment & are finished with durable Powder Coated Paint.

02

7. 75 mm gap between the walls is filled with special grade glass wool for proper insulation and to avoid heat losses. Inner chamber is fabricated with ribs to adjust shelves to any convenient height. Supplied with 2 or 3 removable shelves. Shelves are made of polished SS Sheet.

8. Insulated door is fitted with heavy hinges with a special design spring – loaded door closing device.

9. Door gasket made of synthetic rubber compound instead of Asbestos.10. Heating elements are made of high grade imported Nichrome wire which are insulated inside

the porcelain beads and are generally placed suitably in Air Path for uniform temperature all over the space.

11. Temperature is controlled by an electronic digital temperature controller-cum indicator, provided with air Circulating fan for providing homogenous temperature throughout the chamber with wide temperature 50°C to 250°C ovens for various applications.

12. Air ventilator ports provided on both sides at top to ventilate, gases and fumes if any.13. Control Panel : The equipment is provided with a panel having a digital temperature control

knob. ON/OFF switch, two pilot indication lights and provision for fixing the TIMER.14. Supplied with cord and plug. Suitable to operate on 220 V single phase, 50 Hz, AC supply.15. Inner Chamber 455Wx605Hx455D S.S. (304 grade)-03 Nos16. Hot air oven with three sides heating elements, temperature range 50 0 C to17. 2500 C +/- 10 C controlled by imported thermostat, made of S.S. W x H x D 605 x 910 x

605mm, fitted with Air Circulation Fan and L shaped Thermometer 01 No18. 3 shelves made up of wire mesh in the inner chamber.19. Temperature control from 50- 300 degrees, with control knob. Temperature to be adjusted

with reference to thermometer, provision to insert glass thermometer and electronic digital control cum indicator. Circulating fan with motor for uniform temperature, with electronic digital timer with alarm.

20. Suitable servo stabilizer6. Onsite warranty: 5 years

GVDVPP005 Refrigerator Energy Efficiency :5 Star Rating

Capacity :345 LitersInstallation Type :Free-StandingForm Factor :Standard Double Door

02

Special Features :Inverter, ConvertibleColour :Elegant InoxVoltage :100 VoltsDefrost System :Frost FreeShelf Type :Toughened GlassMaterial :Steeltemp 2-80CIt should be provided with suitable stabilizer, lower stand and Fridge handle cover and top cover (with pockets).

GVDVPP006 Slide cabinet and slide boxes

1. For keeping 75x25 mm slides in vertical position one after the other. Made of CRC steel with powder coated paint finish.

2. Drawers and slides in vertical position Movable drawers in a slot, completely removable for easy lifting of slides.

3. Accommodable slide capacity 1000 slides and lockable doors.4. Slide boxes

Qty: 10 no. Capacity: 100 slides-75x25 mm slides

01

GVDVPP007 Staining jars, coupling jars, bottles

Staining jars1. An all glass rectangular staining jar which accommodates 8 to 16 slides and comes with a

glass lid.2. Its wide top should eliminate the need for forceps in the handling of the slides.3. It should accommodate slides up to 4" x 1½" (102 x 38 mm) in size.

Drop bottles:250ml capacity built-in stem all polypropylene; leak proof screw cap made of polypropylene.

05

GVDVPP008 Tissue cutting boards

1. Should be made of polypropylene.2. Measurements: 300 mm(L) x 210mm(W) x 12mm(H).3. It should be sterilized via Autoclave, Microwave, Gas Sterilization, Chemical Disinfectant

Sterilization.

02

GVDVPP009 Racks for specimen jars, bottles

1. It should be totally dismountable and can be modified or expanded height and lengthwise2. Size : 40 x 40 inches with 14 gauge roll steel3. 6 shelves includes top and bottom & should be adjustable with 20mm pitch4. Grey enamel paint with corrosion resistant

20

GVDVPP010 Specimens jars, 10 x 5cm -10 no. 01

wide-mouthed bottle (set)

20 x 10 x 5cm -10 no.20 x 20 x 12cm -10 no.26 x 15 x 10cm -10 no.30 x 17 x 9cm -10 no.25 x 25 x 12cm -10 no.

The items made up of glass with lids GVDVPP011 Autopsy table

for small animals

1. Mobile, all stainless steel construction.2. Work area with concave embossment towards drain.3. Special underside-coating for anti-noise damping.4. Large diagonally positioned drains. 4 castors, 2 with locks.5. Max. load: 500 kgs. Material: Stainless steel

Dimensions: 2500(L) x 1000(W) x 700(H)mm

01

GVDVPP012 Carcass trolley 1. Multi-functional hydraulic carrier designed for hospitals, coroner's facilities and mortuaries.2. Durable and economical stainless steel adjustable height body transporter.3. Hydraulic base with height adjustment via foot pedal.4. 1.5in/3cm square, .12in tubing thickness, 304 stainless steel vertical end rails.5. Heliarc welded for added strength and durability.6. 8in/20cm casters all with brake mechanisms. Brake will lock instantly with a single foot

pedal.6. Solid surface base for easy cleaning

01

GVDVPP013 Monopan digital balance

1.Readibility :- 0.01mg2. Weighing Capacity:-1mg - 100 gm3. Repeatability:- ± 0.05mg4. Linearity:- ± 0.1 mg5. Weighing cap. -- 200-230 g6. Pan Size ---- 80- 100 mm; enclosed in chamber5. Stabilization time: ≤ 3 sec.7. 6. Stabilizer (Compatible to balance)0.5 KVa Three year warranty

01

GVDVPP014 Centrifuge 1. Multipurpose refrigerated centrifuge2. Control interface with numeric input buttons for setting and editing the running conditions3. Pulse key function for quick spin4. Fixed angle rotor RPM should be at least 15000rpm or 25910g5. Swingout rotor RPM should be at least 5000rpm or 5394g

01

6. Fixed angle rotor should have at least 6X (250 and 15ml capacity) and 30X 1.5/2.0ml slots

7. Swing out rotor should have at least 4X 750ml capacity or 80X 15 ml capacity8. Temperature range should include -10 to 40 degrees9. Fast cool option should be there10. Automatic rotor identification option should be included11. Imbalance cut off option, safety lid lock option, lid drop protection options should be

included. 12. Should include fixed angle 8X50 ml rotor with 50ml and 15 ml adapters, fixed angle

12X15ml conical rotor, fixed angle 30x1.5/2.0ml rotor.13. Should include swingout rotors for 15 ml and 50ml tubes and 96 well plates14. Should be supplied with suitable servo stabilizer

Should include 5 year on site warrantyGVDVPP015 Wintrobe tube

with racksWintrobe tube:ID (mm) 2.55Length (mm) 240Should have yellow calibration with round bottom. Should be made of soda lime glass.1. Wintrobe tube racks: should be made from sheet metal and finished in white enamel. The

stand should hold 6 Wintrobe tubes. Positions are numbered for easy identification.

05

GVDVPP016 Haemocytometer

Haemocyte meters in Cardboard box with Spare RBC and WBC pipettes and neubauer Counting chambers

15

GVDVPP017 Phase contrast microscopes

1. MEA53300- Inverted microscope Eclipse Ti S Main body (100-240v) equipped with side port.

2. Coaxial coarse/fine focus w/tension adjustment on course Light-distribution3. 100 Eyepiece and 20 Eye-80 Left(*)4. MXA29009- Anti-mould agent5. MXA22062- Vinyl Cover Type 1086. EYE PIECE TUBE BASE UNIT:MEB55800- TI-T-B-Eye piece Tube Base Unit7. EYE PIECE TUBE :MEB52320- TI-TD Eyepiece Tube D8. EYE PIECES:MAK10100- CFI 10X w/diopter adjustment (F.O.V.22mm), MAK99000- CFI

UW Eyepiece Guard(for 10x eyepiece lens)9. STAGE:MEC54100- TI-SP Plain stage,MEC55100- TI-SAM Attachable mechanical stage10. HOLDER:MFC35015- C-HU Universal Holder: Slide Glass

01

11. (76.5x27.0mm),Haemocytometer(76.0x35.0mm),petri Dish (0.30 to 0.65),Microplate, Terasaki(81.5x56.0mm)

12. DIASCOPIC ILLUMINATION:MEE59905- TI-DH Diascopic illumination Pillar 100w,MBE75225- D-LH/LC Percentered Lamp house,MXA30434- Halogen Lamp 12v-100w LL, MEF51001- TI-100WRC 100W Lamphouse Remote Cable,MEF52251- TI-P5100W/A Power supply 100-240V/A,MBF11300- Power Cord Type BE fro 220-240v

13. FILTERS:MBN11200-Filter 45mm, GIF,MBN11500- Filter 45mm, Heat absorbing,MBN11710- Filter 45mm,NCB 11, Day light colour balance,MBN21802- Filter 45mm,ND2 A, Neutral Density, MBN21816- Filter 45mm, ND16 A, Neutral Density

14. TURRENT CONDENSER:MEL51000-TI-C System Condenser Turret,MEL56200- TI-C-LWD LWD Lens for system condenser Turret

15. N.A. 0.52 W.D.(O.D.) 30mm16. MEH41100- TE-C LWD PH-1 Module17. SEXTUPLE NOSEPIECE:MEP51315- TI-N6 SEXTUPLE NOSEPIECE, MXA2204-

Nosepiece Cap18. OBJECTIVES19. MRP00042- CFI Acromate 4x N.A. 0.10, W.D.30.0mm,MRP40102- CFI Acromate

ADL10XB N.A. 0.25, W.D. 6.2mm, PH-119,MRP46202- CFI Acromate WD ADL 20XF N.A.0.40, W.D.3.1mm,PH-1,MRP45422- CFI Acromate WD ADL 40XC N.A.0.55, W.D.2.7-1.7mm,Corr 0-2.0mm,PH-2,MQA11020- Digital camera head DS-Fi2 2/3” high density- CCD;

20. Total no of pixels: 5.24 Megapixels, Digital output: 14bit, Gain:1-46x, Binning21. modes:2x2, 4x4, Exposure time: 130micro second to 60sec. Dynamic range:more than

1000:122. MQA25020- CAMERA CONTROL UNIT DS-U3 (NIS Elements F Software for image

aquisation)23. MQF11010- DS Camera I/F cable 20/2624. MQF52055- AC adopter 225. MBF11300- Power cord BE (220-240v)26. MQD42000- C-Mount TV Adopter A27. SPARE LAMP:HALOGEN LAMP,MXA20434- Halogen lamp 12v-100w LL

Onsite warranty from the date of installation for 5 yearsGVDVPP018 Mechanical cell

counter for DLCThe cell counter should be useful for counting various types of WBCs 05

GVDVPP019 Microhaematocrit centrifuge

Microhematocrit centrifuge:1. Digital Speed Indicator2. Stepless speed regulator3. 0-60 minutes digital countdown timer4. 0-15 minutes digital countdown5. timer6. Safety Lid interlock to prevent cover opening during centrifugation7. Press Switch for quick acceleration to full speed8. Max. Speed rpm 160009. Max. RCF ‘g’ 1660010. Max. Capacity ml 4011. W x D x H mm 280 x 350 x 29012. Supply: 220-240 Volts 50 Hz Single Phase.13. Should include haematocrit reader

Reader:Designed for use with capped or sealed 75mm microhematocrit capillary tubes. Made of durable vinyl-laminated plastic for easy cleaning.7 1/2”L x 4 1/2”W

01

GVDVPP020 Westergren tube with racks

Westergren tube:1. Overall length- 300±1 mm2. External diameter-6.5 ±0.5mm3. Internal diameter (bore)- 2.55±0.15mm4. Ovality of bore-less than 0.1mm5. Length of measuring part-200±1 mm6. Length of tapering portion-6±2mm7. Wall thickness of orifice at least 0.5mm

NOTE:Ovality of bore is the difference between maximal and minimal diameters at any cross section of the tube.Westergren tube racks:

1. Racks feature leveling bubbles and adjustment screws2. Tubes are held firmly in a perpendicular position to ensure accurate readings.

For Use With (Application) For westergren and wintrobe tubesMaterial Glass

05

Positions 10Should include Disposable westergren pipetts-200 no.

GVDVPP021 Deep freezer (-200C)

1. Horizontal type2. Should be useful for storing small animals and specimens3. 7.2 cubic feet volume approximately4. Shall provide suitable servo voltage stabilizer.Onsite warranty for 5 years from date of installation.

01

GVDAGB001 Centrifuge- 1. Multipurpose refrigerated centrifuge2. Control interface with numeric input buttons for setting and editing the running conditions3. Pulse key function for quick spin4. Fixed angle rotor RPM should be at least 15000rpm or 25910g5. Swingout rotor RPM should be at least 5000rpm or 5394g6. Fixed angle rotor should have at least 6X (250 and 15ml capacity) and 30X 1.5/2.0ml

slots7. Swing out rotor should have at least 4X 750ml capacity or 80X 15 ml capacity8. Temperature range should include -10 to 40 degrees9. Fast cool option should be there10. Automatic rotor identification option should be included11. Imbalance cut off option, safety lid lock option, lid drop protection options should be

included. 12. Should include fixed angle 8X50 ml rotor with 50ml and 15 ml adapters, fixed angle

12X15ml conical rotor, fixed angle 30x1.5/2.0ml rotor.13. Should include swingout rotors for 15 ml and 50ml tubes and 96 well plates14. Should be supplied with suitable servo stabilizer

Should include 5 year on site warranty

01

GVDAGB002 Microscope 1. Monocular type2. Total Magnification: 40x – 1600 x, Eyepiece WF 10x, H 16x Objectives3. 4x,10x,40x, 100x oil SL , Built in LED illumination With battery backup, Coarse &Fine

Focusing system. Viewing Head : Monocular 45 deg inclined, tube: 360 degree Rotatable . Double layer mechanical Stage120x120mm Moving Range 60 x 30mm

4. Condenser with IRIS diaphragm & Filter. Fully Imported.5. A round base with joint revolving arm for moving the magnifying lens over the stage.

Focusable by rack and pinion. Eye point 10X & 20 X eye pieces in a wooden box.

20

6. Should be of reputed brand. No OEM equipment should be quoted.Onsite warranty from the date of installation for 5 years

GVDAGB003 Phase contrast microscope

Specification: Stand: Single mold sturdy stand with anti rust materials, Extended base with hand rests for

enhanced stability and comfort. Viewing bodies: Sidentopf Trinocular tube, 30˚ inclined, 360º rotatable, Inter papillary

distance 48-75mm. Eye piece: Wide field focusable paired eyepiece WF10x/20mm and 20X/12mm with foldable

eye guard, anti-fungus coating. Nosepiece: Reverse angle quadruple nosepiece (Ball bearing type) with click stops and rubber

grip, anti-fungus coating. Objectives: RP series DIN Infinity Corrected phase Objectives 4x, 10x, 40x(spring loaded),

100x (spring loaded, oil) Mechanical stage: Rockless X axis, double plate mechanical stage size 200 x 160mm, X/Y

travel range 78mm x 54mm, Low drives movement controls. Hard coated surface for scratch resistance.

Condenser: Sub stage centerable phase turrer condenser Focusing: Coaxial coarse and fine focusing on ball drive system for smooth operation. Illumination: Halogen 6V-30W illumination with variable illumination control. Up to 2,000

hours of Halogen lamp life Electrical: Input 220V - 240V AC Should include high definition 5MP HDMI camera should include Wifi, SD Memory card or USB based storage (of at least 64GB) and mouse for

computer free operation. should be able to work with live view and should come with live measurements on HDMI

screen without PC and can also be connected to PC for simultaneous operation that has all in one camera HDMI + USB + SD Card. The camera is attached to a 18" HD monitor. 

5. Warranty:2 years

01

GVDAGB004 Slide Boxes 1. Dimensions (inches):8 ¼ x 6 ½ x 1 ¼2. It should store 100 microscopic slides (3’’ x 1’’ or 75mm x 25 mm slides)

It should be heavy duty polystyrene with rust resistant , nickel plated clips and hinge pins.

03

GVDAGB005 Specimen racks Specimen racks1. It should be totally dismountable and can be modified or expanded height and

lengthwise

01

2. Size : 40 x 40 inches with 14 gauge roll steel3. 6 shelves includes top and bottom & should be adjustable with 20mm pitch4. Grey enamel paint with corrosion resistant.

GVDAGB006 Almirah Almirahs1. Should be made up of steel and size 1980 mm (H) X 900mm (W) X 480mm (D) from 22

gauge for body and 20 gauge for doors2. It should have four shelves making five compartments of standard size which can be

adjustable.3. The doors must be provided with stiffners made of MS Sheet spot welded to the doors4. The almirah should be equipped with a special three way bolting device with tongue in

groove inter locking mechanism with six lever locks5. The handle made from a non ferrous metal alloy, chrome plated.6. It should be provided with a standard lock and 5 keys

The complete almirah duly painted with synthetic grey enamel paint of approved shade in and outside

01

GVDAGB007 Storage boxes for charts, diagrams

1. should be made of Transluscent material for easy viewing of contents with a lid2. Modular & latchable3. Latchable handles for a secure fit4. 50 L capacity5. should Fit letter and legal sized files, chart size6. Dimensions (approximately): 12" H. x 18" W. x 14" L.

01

GVDAGB008 Computer Desktop

Computers1. GHz intel Core i7-7100U (2.4 GHz, 3 MB cache, 2 cores) 7th gen processor2. 1Tb 7200rpm Hard Drive, 4GB DDR4 RAM, OS Windows 10, office 20103. DVD Drive read & writer4. 18.5” LED monitor with screen resolution: 1920 x 10805. Audio details: Head phones, Speaker Description: DTS studio sound dual 2 w speakers6. Graphics coprocessor: Intel HD graphics 6207. Connectivity type:Wi-Fi, Bluetooth 4.0 M.28. Wireless Type:802.11b, 802.11.g,802.11.n9. Number of USB 3.0 ports -2(front side of CPU) +3 (back side of CPU)10. Number of HDMI Ports :211. Number of Audio –out ports-112. Number of Ethernet ports-113. Number of microphone ports:114. Mouse with pad15. Keyboard16. UPS with minimum 30 mins power backup

20

17. USB Ports (3.0) Front 2, Back 318. Antivirus protection for 3 years19. Must be a of standard brand like Dell, HP etc, or equivalent and must not be assembled

one. 20. On site warranty for 3 years from date of installation and next 3 years free comprehensive

AMCComputer table & accessories:

1. Product dimensions: Length -19 inches, width 23 inches, height 29 inches with wheels below

2. Primary material: MDF3. Color beech, style: modern4. Spike: Plastic, 6 outlet sockets, Surge protector, compatable with world wide plugs,

6500A spike current , Master switch with LED indicator, 5m heavy duty power cord5. Suitable good quality armless revolving chairs (Godrej or equivalent quality)6. On site warranty for 3 years from date of installation and next 3 years free AMC

GVDANN001 Wiley Mill 1. The Wiley Mill should be all steel construction, with four rotating steel cutting knives, easy cleaning,

2. 7 3/4” chamber dia.3. 141 cu. in. chamber vol.4. 2 1/4” dia. Input5. 50-1,000 gram sample vol.6. 800 rpm at 60 Hz7. 667 rpm at 50 Hz

01

GVDANN002 Hot air oven 1. Hot air ovens (memmert heater) are sturdy double walled units, inner chamber made of S. S. And outer made of mild steel with power coating.

2. Gap between the walls fitted with glass wool insulation to avoid heat loses.3. Heating elements are made of high grade chrome plated microme wire. temp. Is controlled

by thermostat. Temp. Range 50 c to 250 c and accuracy : +- 2 c.4. Air ventilations are placed on top of both sides to remove hot gases / fumes.5. In memmert type units heaters placed at the right and left side of the inner chamber. All the

control switches & pilot lamps are fitted on the front panel. Trays should be supplied with G. I. wire mesh.

6. Inner chamber is made of Highly Polished Stainless Steel. Outer chamber is made of Mild Steel Sheet duly pre-treated in seven tanks process for surface treatment & are finished with durable Powder Coated Paint.

02

7. 75 mm gap between the walls is filled with special grade glass wool for proper insulation and to avoid heat losses. Inner chamber is fabricated with ribs to adjust shelves to any convenient height. Supplied with 2 or 3 removable shelves. Shelves are made of polished SS Sheet.

8. Insulated door is fitted with heavy hinges with a special design spring – loaded door closing device.

9. Door gasket made of synthetic rubber compound instead of Asbestos.10. Heating elements are made of high grade imported Nichrome wire which are insulated inside

the porcelain beads and are generally placed suitably in Air Path for uniform temperature all over the space.

11. Temperature is controlled by an electronic digital temperature controller-cum indicator, provided with air Circulating fan for providing homogenous temperature throughout the chamber with wide temperature 50°C to 250°C ovens for various applications.

12. Air ventilator ports provided on both sides at top to ventilate, gases and fumes if any.13. Control Panel : The equipment is provided with a panel having a digital temperature control

knob. ON/OFF switch, two pilot indication lights and provision for fixing the TIMER.14. Supplied with cord and plug. Suitable to operate on 220 V single phase, 50 Hz, AC supply.15. Inner Chamber 455Wx605Hx455D S.S. (304 grade)-03 Nos16. Hot air oven with three sides heating elements, temperature range 50 0 C to17. 2500 C +/- 10 C controlled by imported thermostat, made of S.S. W x H x D 605 x 910 x

605mm, fitted with Air Circulation Fan and L shaped Thermometer 01 No18. 3 shelves made up of wire mesh in the inner chamber.19. Temperature control from 50- 300 degrees, with control knob. Temperature to be adjusted

with reference to thermometer, provision to insert glass thermometer and electronic digital control cum indicator. Circulating fan with motor for uniform temperature, with electronic digital timer with alarm.

20. Suitable servo stabilizer7. Onsite warranty: 5 years

GVDANN003 Hot plate bench 1. Cooling water consump. ca. 5 l/min Nominal voltage 230 V AC, 50 Hz Nominal at stage 1900 W Weight 42 kg

2. Dimensions (W x D x H) 340 x 640 x 860 mm3. Compressed air pressure 4 - 5 bar Capacity boiling vessel 1,8 L Interface 2 x RS

485Programs 9

01

4. Water connection 2 x ¾ Inch thread Compressor (optional) 4 - 5 bar Fibre Bag System 36-place

5. 10-0015 FBS 36 FibreBag System 36-place, consisting of: 1 x serial heater 6-place 2700W, 6 x beaker 1000 ml, 6 x carousel 6-place, 1 x handle for

6. carousel, 36 x glass spacer, 6 x support stand with ring, 6 x condenser7. made of glass with tubes, (W x H x D) 900 x 600 x 230 mm

7. Application: Crude Fiber estimationGVDANN004 Electronic

Monopan balance

1. Specification: Fine Range of Weighing Capacity of 100 with readability of 0.01mg2. Innovative all-glass draft shield, with smooth-action doors that open extremely wide3. Excellent, high-contrast, easy-to-read display, with especially large digits (16.5 mm)4. Built-in, motorized calibration weight. For the highest weighing accuracy at the touch of a

key5. RS-232C serial interface port ISO/GLP-compliant logging of calibration, adjustment and

weighing data using an optional data printer or a PC6. Monolithic weigh Cell Technology isoCAL calibration and adjustment function.7. Four digital filter levels allow the balance to be optimally adapted to the particular8. ambient conditions at the place of installation9. Built-in application programs: counting, weighing in %, net-total formulation;10. animal weighing; mass unit conversion by toggling between 2 units11. Technical Specifications :12. Warranty: 2 years13. Readability 0.01 | 0.1 mg14. Weighing capacity 100 | 220 g15. Weighing pan (mm) Ø 8016. Response time < 6 | 3 s17. Repeatability <± 0.05 | 0.1 mg18. Linearity <± 0.1 | 0.2 mg19. Calibration Internal20. Should be of standard make, No OEM product.

03

GVDANN005 Muffle furnace 1. Designed for multiple applications including heat treating, ceramic firing, ashing and thermocouple calibration. Heavy duty construction for durability having powder coating finish. No exposed long lasting Kanthal A-1 heating elements.

2. Maximum energy efficiency to be achieved with high thermal efficient ceramic insulation

02

surrounding the chamber should be present. Solid state safety fuse controller with automatic heater cut off facility in case of temp. overshoot. Automatic auto tuning Microprocessor based PID Temp. Controller with Dual Digital Indicator / sensor. Maximum Temperature 350°C to 1200°C.

3. Working Temperature 400°C to 1160°C.21. Chamber size : 6” x” 6x 12”, Working Size: 28” x 25” x 23”, Power : 3.5 k.w.

GVDANN006 Dessicator 8. 3082 Dessicators with cover and porcelain plate ,plastic knob, Borosil. product code 3082088.Approx ID Ground Flange mm 250

06

GVDANN007 Suction pumpRegulatory status

European Economic Area(EEA)

CE This mark on the product indicates compliance with Directive 93/42/EEC relating to medical devices, Class IIa.

Dimensions and weight Dimensions Height: 210mm Width: 305mm

Depth: 375mm

Weight 9.3 kgPower switch Marking The power switch is marked. A white LED in

the center signalizes it is turned onPower requirements

Power supply 100-240 V~

Fusing 2 x T1.6 AH

Frequency 50/60Hz Power rating

120 W

Environmental conditions

Ambient Temperature

Operational: +5ºC to +40ºC (+41ºF to +104ºF)Storage: -20ºC to +50ºC (-4ºF to

+122ºF)Relative humidity

Operational: 30-75 %

Storage: 20-95%

Atmospheric pressure

Operational/Storage: 70.0 to 106 kPa

Fluid Ingress In accordance with EN IEC 60601-1/UL 60601-1, the product is marked IP21 to indicate that it is provided with an enclosure that prevents entry of such an

01

amount of falling liquid as might interfere with its safe and satisfactory operation when correctly positioned.

Resistance to chemicals

The external surfaces of the Olympus KV-6 are resistant to: 2% aqueous neutral detergent, 70% ethyl alcohol, isopropyl alcohol, water.

Pump specification

Nominal vacuum: 95 kPa Nominal free air flow rate: 50 l/min, adjustable to 40 or 60 l/min.

In accordance with ISO 10079-1, the unit is marked with the words ‘HIGH VACUUM, HIGH FLOW’ to indicate it has a vacuum of at least 60 kPa in 10 seconds and a free air flow rate of 20l/min or greater.

Thermal cut-out

The temperature is observed by a sensor in the housing. If the temperature in the housing exceeds 80 °C (176 °F), the software stops the motor and turns on the yellow LED. It is possible to restart the motor again as soon as the temperature in the housing drops below 70 °C (158 °F).

Single use suction liner

To prevent fluid from being drawn up to the pump the single use suction liner contains a mechanism to shut off the flow when the liner is overfilled. This mechanism is activated when contact is made with aspirated fluid.

Suction jar The suction jars can be autoclaved up to 135 ºC or disinfected. The jar is impact resistant.

Suction jar lid The suction jar lid clips and where applicable the float mechanism, are autoclavable up to 135 ºC. The inlet connection (from the endoscope) is marked with the word PATIENT, the outlet connection (to the pump) is marked with the word VACUUM.

Tubing Use only tubing specified in the KV-6 Instructions for Use, otherwise equipment malfunction may result.

Vacuum gauge Range: 0 to 100 kPa Accuracy: ±2.5%21.

GVDANN008 Kjeldhals Digestion & Distillation system

Digestion system should work with Infrared Digestion system with Radiation heating Technology. Digestion unit should comprise of 12 x 250ml tubes, Complete for 12 tubes 250 ml. Rapid digestor with IR heating elements. The capacity control adjustment should have step less from 0-100 %. Energy time programs are to be provided. It also should contain- Two-tier console- Exhaust manifold made of glass in V2A cassette- Drip tray

2 each

- Water jet pump, 1,5 m Isoversinic tubing incl.- Digestion tubes 250 ml (12 pieces)Nominal voltage: 230 V AC, 50/60 HzDistillation systemMicroprocessor-controlled steam distillation unit with embedded computer for convenient operation via a 7” full-colour TFT with capacitivedisplay (touchscreen). Also it should meet all requirements of established standards for quality control and assurance, such as GLP / ISO 17025. Equipment should be suitable for all established methods of Kjeldahl determination and other physical separation methods for steam-soluble substances, such as 64 of the German Food Law, ASTM, AOAC, EPA, DIN/EN/ISO, VDLUFA. It should be chemical-resistant and corrosion-free plastic housing and an automatic, maintenance-free steam generator for distilled or pprox.d water.Special applications, this distillation unit should be equipped with an acid resistant reagent pump. It should conserve energy, the system should switch to standby mode during break periods; distillation to be started immediately at any time. The distillation time for nitrogen determination by the Kjeldahl method should be pprox.. 3.5 minutes. It should also estimate alcohol.Provision for addition of water, sodium hydroxide automatically, as well as the steam output, distillation time and sample residue suction time. The pump for adding H2O, sodium hydroxide or reagent can be calibrated for exact dosing. Provision for the addition of reagents manually throughout the distillation process through touch screen button.Equipment may be provided with a desktop, USB mouse and USB Key board. It should provide acoustic feedback to different events, such as end of distillation or other messages. Facility for the level sensors for reagents, water and chemical waste are directly usable with standard 5L, 10L and 20L canisters. This makes dangerous transfer of chemicals into other tanks unnecessary.Provision of sample tubes with a volume up to 1300 ml 12 numbers.Digital BuretteUltra-high precision, easy drop wise titration, replaceable piston/cylinder assembly and an optional PC interface.The control elements should have separate buttons for On/Off and Pause; CLEAR button and to reset the display and select functions. Easy-grip hand wheel action and smooth precision gears for fast or drop-wise titration Telescoping filling tube (170 – 330 mm), Recirculation tube, 4 batteries4. (AAA/UM4/LR03), 3 PP bottle adapters (GL 45/32, GL 45/S 40, GL 32/NS 29/32), 2 amber

colored light shield inspection windows.GVDANN009 Soxhlet

apparatus set1. It should have 4-place extraction unit, which to be controlled and programmed using the

Multistat controller. Capable of fullyautomatic, unattended extraction process. It should have Pneumatic control with intrinsically controlling elements. Continuous monitoring of cooling water and compressed air.

2. Spark proof, electric heating with heating ranges of 135°C, 200°C, and 300°C. Protective safety glass front door closing automatically during the extraction. Solvent recovery and level sensor for solvent tank.

3. It should have an additional 5 m power cord, Extraction beaker macro (16 pieces), Extraction thimbles 33 x 80 (50 pieces), Holder for extraction thimbles (4 pieces), Handling tool, Software for control and monitoring of max. 4 place extraction unit. CD with controlling software, GerBus adapter and Software key.

4. Compressor with support frame, 230VAC 50-60Hz

01

GVDANN010 Water bath 1. 355X405X100mm, 12 holes of 75mm diameter.2. Double walled automatic temperature controlled room temperature 30 C to 110 C plus/

minus 1C thermostat.Stainless steel inside glass wool insulation provided with concentric rings with thermometer fit.

01

GVDANN011 Hot plate Temperature 250°CHeating Plate Cast IronController Energy RegulatorPower Supply 220 / 230 Volts, 50 HzSize 19cm round

-Overhead stirrer-PID Controller-Stainless steel heating plate-Digital temperature display-Support stand

02

Annexure IIDeclaration

1. I/We have not been black listed in any department due to any reasons during last 3

years

2. I/We have not been demoted to lower category in any department for not filing the

tenders after buying the tender schedules in a whole year and their registration had not

been cancelled for a similar default in two consecutive years.

3. I/We will agree to get disqualified my(our)selves for any wrong declaration in respect

of the above and get my/our tender summarily rejected.

4. The soft copies uploaded by me/us are genuine and not forged. Any incorrectness /

deviation noticed can be viewed seriously and apart from cancelling the work duly

forfeiting the bid security, criminal action can be initiated including suspension of

business and/ or black listing.

5. I/We submitting a demand draft no. _____________dated _________ issued by

____________________________for Rs. ____________ towards the EMD.

Signature of TendererDateAddress

Annexure III

Check ListSl.No Yes/ No Name of the Document

1. Declaration Form (Annexure II)

2. Manufacturing License / Authorization letter from the

Manufacturing firm

3. Earnest Money Deposit

4. VAT/Sales Tax/GST Clearance Certificate or payment

particulars for preceding two years along with

supporting Documents (2016-17 and 2017-18)

5. Annual Turnover Assessment order for the preceding

two years (2016-17 and 2017-18) certified by

Commercial Tax Officer / Chartered Account

6. Copies of balance Sheet, Profit and loss Account for

last two years i.e. (2016-17 and 2017-18) duly certified

by the Auditor

7. Copy of GST registration certificate

8. Users list for the item/ equipment during past 4 years

9. BIS / ISO/ CE issued by the Competent Authority

10. APSSIDC/NSIDC/MSME Certificate, if applicable

11. Government Ownership Certificate, If applicable

12. List of service centers with contact details for each of

the equipment

ANNEXURE – IV

FINANCIAL BID

(Not to be included with the technical bid either online or offline)

I/We quote the rates FOR, NTR COLLEGE OF VETERINARY SCIENCE, GANNAVARAM inclusive of all taxes, duties, transportation, insurance, installation etc., as below.

Sl No. Name of the item No. of Units

Price per Unit (Rs)

Total amount (Rs)

The articles will be ready for delivery within ____ days from the date of receipt of firm orders.

Yours faithfully,

(Signature and stamp of the Tenderer state legal status whether prop. Partner, Registered firm, Company etc)

Encl: Information brochure enclosed

EMD – DD No. Dt. For Rs. ____________

Note: 1. Attach additional sheets giving full particulars such as name and address of the proprietor or list of partners and their addresses or particulars of registered firm or of the company and the specifications of the equipment furnished.

1. Rates quoted should be marked clearly with main price and taken separately. Total price after taking all the actuals will be taken as financial quote for comparison.