+ All Categories
Home > Documents > Nastec Pilot

Nastec Pilot

Date post: 28-Mar-2016
Category:
Upload: nastec
View: 219 times
Download: 3 times
Share this document with a friend
Description:
PILOT is an electronic device for the control of single phase and three phase motors (pumps). PILOT, in combination with a VASCO inver- ter, will start and stop D.O.L. pumps while providing them with full protection
2
“ the most compact and cost-effective solution for the full protection of a pump”
Transcript
Page 1: Nastec Pilot

“ the most compact and

cost-effective solution for

the full protection of a

pump”

Page 2: Nastec Pilot

Nastec srl, Via della Tecnica, 8, 36024, Mossano, Vicenza, Italy,Tel. +39 0444 886289, Fax +39 0444 776099, [email protected], www.nastec.eu

Nastec reserves the right to modify without notice the tecnical features contained in this catalogue.

ca

tPIL

OT

_e

ng

_0

2

PILOT is an electronic device for the control of

single phase and three phase motors (pumps)

which provides protection against :

Overcurrent, phase loss, excessive number

of starts.

The backlit LCD displays the running current

and PILOT stops the pump if the maximum

value set by the user is exceeded.

The maximum number of pump starts is also

user selectable and PILOT will stop the pump

operation if this value is exceeded.

Dry running

PILOT provides a display of the power factor

value (P.F. or cosø) and allows the user to set a

minimum threshold value for normal opera-

tion. PILOT will stop the pump below this value

to protect against dry running.

PILOT will make up to 5 automatic restart at-

tempts following an alarm condition at time

intervals set by the user.

PILOT stores in memory the number of pump

starts and total running hours. The alarm his-

tory is also stored to assist with servicing.

The body is constructed entirely of aluminium,

making PILOT extremely solid and easily

cooled.

The IP55 protection makes it possible to install

PILOT even in humid and dusty environments.

Also available:

2 digital inputs, user selectable as normally open

(N.O.) or normally closed (N.C.), for connection of

external control switches. These contacts (volt free)

allow the pump to be stopped or started by float swi-

tches, pressure switches, thermal protection, etc...

1 output relay contact to control an external alarm

(250 VAC or 30 VDC , max 5 A) . This is user configura-

ble as N.O. or N.C.

Contacts to connect a boost capacitor to assist the

starting of single phase pumps.

PILOT, in combination

with a VASCO inver-

ter, will start and

stop D.O.L. pumps

while providing them

with full protection.

Complete pump protection

Model Voltage [+/- 10%]

50/60 Hz Maximum

current Weight

[kg]

PILOT 112 1 X 230 VAC 12 A 2

PILOT 118 1 X 230 VAC 18 A 2

PILOT 312 3 X 400 VAC 12 A 2,2

PILOT 325 3 X 400 VAC 25 A 2,4

PILOT 112 - 115V 1 X 115 VAC 12 A 2

PILOT 118 - 115V 1 X 115 VAC 18 A 2

PILOT 312 - 230V 3 X 230 VAC 12 A 2,2

PILOT 325 - 230V 3 X 230 VAC 25 A 2,4

* capacitor not included in the singlephase models (available upon request)

Max. environment temperature: 40°C (104 °F)

Max. altitude: 2000 m

IP Protection: IP55 (NEMA 4)

180

mm

180 mm 120 mm

2 x PG21

2 x PG9


Recommended