NATIONAL IRANIOEC SPEC. - صفحه...

NIOEC-SP-70-03(1) DOCUMENT CODE NO. OF PAGES: 38

PLAN/PRJ/SUB UNIT PHASE DISCIPLANE DOCUMENT TYPE SERIAL NO. REV. NO. DATE NIOEC 000 EG IN SP 7003 A0 JULY, 2005

NATIONAL IRANIAN OIL REFINING & DISTRIBUTION COMPANY

NATIONAL IRANIAN OIL ENGINEERING

& CONSTRUCTION COMPANY

NIOEC SPECIFICATION

FOR

INSTRUMENT INSTALLATION MATERIAL

FIRST EDITION

JULY, 2005

THIS SPECIFICATION IS THE PROPERTY OF NATIONAL IRANIAN OIL ENGINEERING & CONSTRUCTION COMPANY. IT IS CONFIDENTIAL AND ALL RIGHTS RESERVED TO THE OWNER. NEITHER WHOLE NOR ANY PART OF THIS DOCUMENT MAY BE DISCLOSED TO ANY THIRD PARTY, REPRODUCTED, STORED IN ANY RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY MEANS WITHOUT THE PRIOR WRITTEN CONSENT OF THE NATIONAL IRANIAN OIL ENGINEERING & CONSTRUCTION COMPANY

JULY, 2005 NIOEC-SP-70-03(1)

JULY, 2005 NIOEC-SP-70-03(1)

REVISION INDEX

REV. PAGE

1 2 3 4 5 REV. PAGE

1 2 3 4 5 REV. PAGE

1 2 3 4 5 REV. PAGE

1 2 3 4 5

1 26 51 76

2 27 52 77

3 28 53 78

4 29 54 79

5 30 55 80

6 31 56 81

7 32 57 82

8 33 58 83

9 34 59 84

10 35 60 85

11 36 61 86

12 37 62 87

13 38 63 88

14 39 64 89

15 40 65 90

16 41 66 91

17 42 67 92

18 43 68 93

19 44 69 94

20 45 70 95

21 46 71 96

22 47 72 97

23 48 73 98

24 49 74 99

25 50 75 100

NOTES: 1) THIS SHEET IS A RECORD OF ALL REVISIONS TO THIS SPECIFICATION.

2) REMARKS RELATED TO EACH REVISION SHOW A BRIEF DESCRIPTION. THESE REMARKS SHALL BE INTERPRETED IN CONJUNCTION WITH THE REVISED TEXT MARKED BY REVISION NUMBERS.

3) WHEN APPROVED EACH REVISION SHALL BE CONSIDERED AS A PART OF THE ORIGINAL DOCUMENT.

4) NUMBER OF PAGES EXCLUDES THIS SHEET AND THE COVER SHEET.

5 4 3 2 1 0 JULY, 2005 MOMENI ORDOOBADI M.R.FARZAM SAJEDI

REV. DATE PREPARED CHECKED APPROVED AUTHORIZED

JULY, 2005 NIOEC-SP-70-03(1)

1

CONTENTS: PAGE NO.

1. SCOPE.............................................................................................................................................. 2 2. REFERENCES................................................................................................................................ 2 3. UNITS............................................................................................................................................... 3 4. DEFINITIONS ................................................................................................................................ 3 5. NOTES PERTAINING TO ALL INSTRUMENT LINE CLASSES ......................................... 3 6. NOTES PERTAINING TO SPECIFIC INSTRUMENT LINE CLASSES............................... 4 7. INSTRUMENT IMPULSE LINE MATERIAL SPECIFICATION.......................................... 5 8. INSTRUMENT AIR SUPPLY PIPING........................................................................................ 7 9. INSTRUMENT AIR TUBING....................................................................................................... 7 10. ANALYSER AND HOOK-UP TUBING .................................................................................... 7 11. SUPPORTS.................................................................................................................................... 7 12. INSULATION & SEALING MATERIALS............................................................................... 7 13. TAG-NO AND NAME PLATE MATERIAL............................................................................. 7

14. APPENDIX I. INSTRUMENT LINE CLASSES

JULY, 2005 NIOEC-SP-70-03(1)

2

1. SCOPE

This specification defines NIOEC’s minimum requirements for the instrument installation

material, based on the American National Standard Institute Code for Pressure Piping ASME

B31.3 'Process Piping', and NIOEC-SP-50-04.

This specification may be used with other Sections of the ANSI B31 Code, and/or Section I of

the ASME Code, after reviewing for compliance with the applicable sections and modifying as

necessary.

Deviations from this specification will only be permitted on obtaining written approval from NIOEC.

2. REFERENCES Throughout this specification the following dated and undated standards and codes are referred to.

These referenced documents shall, to the extent specified herein, form a part of this specification.

For undated references, the latest edition of the referenced document (including any supplements

and amendments) applies. For dated references, the edition cited applies.

The applicability of changes in the dated references that occur after the cited date shall be mutually

agreed upon by NIOEC and the vendor /contractor.

API (AMERICAN PETROLEUM INSTITUTE) API Publication 941, 1997.

“Steels for Hydrogen Service at Elevated Temperatures and Pressures in Petroleum Refineries and Petrochemical Plants”.

NIOEC (SPECIFICATIONS) NIOEC-SP-50-04

“Specification For Piping Material”

NIOEC-SP-50-09

“Specification For Piping Material Purchase Pipe”

NIOEC-SP-00-10 “Specification For Units”. NIOEC-SP-50-11

“Specification For Piping Material Purchase Fitting”

NIOEC-SP-50-18

“Specification For Piping Material Purchase Valves”

NIOEC-SP-80-02 "Specification For Painting" ASME (AMERICAN SOCIETY OF MECHANICAL ENGINEERS ) B 31.3 “Process Piping” ASTM (AMERICAN SOCIETY FOR TESTING AND MATERIAL) SECTION I “Iron and Steel Products”

JULY, 2005 NIOEC-SP-70-03(1)

3

3. UNITS International System of Units (SI) shall be used in accordance with NIOEC-SP-00-10, unless

otherwise specified.

4. DEFINITIONS Throughout this specification, Hydrogen Service shall mean any service with hydrogen partial pressure greater than 5 bar (a).

5. NOTES PERTAINING TO ALL INSTRUMENT LINE CLASSES 5.1 Item Descriptions 5.1.1 The item descriptions shown in the individual classes are abbreviated and shall not be used for purchase. For Purchase Descriptions, reference shall be made to the Master Commodities catalogue. 5.1.2 Full size and reducing size components shall have the same Item Code Number. 5.2 Manufacturer Reference 5.2.1 Items specified or referenced by manufacturer and figure number are not intended to exclude equal items offered by other manufacturers. Products of reputable manufacturers and of comparable type, quality and characteristics shall be submitted for NIOEC’s approval. Materials shall be supplied from approved vendor list. 5.3 Design conditions 5.3.1 Unless otherwise noted, all pressure and temperatures referred to are at the design conditions. 5.3.2 Selection of steels exposed to hydrogen service shall be in accordance with API Publication 941, 1997 “Steels for Hydrogen Service at Elevated Temperatures and Pressures in Petroleum Refineries and Petrochemical Plants”. Hydrogen Service shall mean any service with hydrogen partial pressure greater than 5 bar (a). 5.4 Material Identification 5.4.1 Valves and Special Items shall be supplied with a metal tag attached, bearing the applicable Item Code Number. 5.4.2 Each individual length of pipe shall be identified in the field with the applicable Item Code Number, as follows: a. The number shall be applied continuously throughout each full length. b. Numbers shall be applied with a Pannier Model TSS Hand Bar and Tube Printer, with E-Z Set Printing Wheel and be changeable dies. The marking ink shall be Pannier 1001 Yellow Industrial Ink. c. Readily identifiable material such as austenitic stainless steel, galvanized, cast iron, copper, or non-metallic will normally be exempt from this requirement.

JULY, 2005 NIOEC-SP-70-03(1)

4

5.5 Colour Coding 5.5.1 Carbon steel flanges with a special smooth, finish shall be colour coded blue. This does not apply to flanged ends of valves. 5.5.2 Alloy pipe, flanges and fittings that could be mistaken for carbon steel shall be colour coded yellow. Special' carbon steel items shall also be colour coded yellow. Each pipe shall have a band of yellow paint approximately 2.5 cm. wide along its full length. Flanges shall be painted all round their periphery and fittings shall have a dot of paint on them. This is a means of alerting Construction that the Material is alloy or otherwise special. Reference should then be made to the manufacturer's markings to determine the exact type of material.

6. NOTES PERTAINING TO SPECIFIC INSTRUMENT LINE CLASSES The following notes, identified by a number in parentheses, on the reference column of the line sheets, become a part of an individual class wherever the same number in parentheses appears in those classes. 1) Valves Valves shall conform to the Purchase Specification NIOEC-SP-50-18 applicable. 2) Pipe Pipe shall conform to Purchase Specification NIOEC-SP-50-9. 3) Fittings Pipe fittings shall conform to Purchase specification NIOEC-SP-50-11. 4) Seal Welding a) Screwed pipe joints shall be seal-welded' where called for in individual Line Classes, except normally the following shall not be 'seal-welded': Tubing Nuts Union Nuts Vent connection Drain Connection Connection at Instrument Body b) All thread shall be clean cut to full depth. Joint shall be made up wrench tight without the use of thread compound. c) Seal welding shall cover the exposed pipe threads at screwed fittings but shall not exceed 10 mm fillet. d) Where deemed necessary, screwed plug valves may be seal-welded, however care must be exercised to avoid excessive heat, resulting in valve distortion. e) Gate and globe valves shall be in a lightly closed position while being seal-welded or socket-welded. 5) Tube Bending Requirements Use Standard radius bends in place of fittings whenever possible. 6) Pipe Bends a) Bends (seamless pipe only) may be used in place of screwed or socket-weld fittings unless otherwise indicated in the individual class. b) Bend radius shall be a minimum of 5 times the normal pipe diameter. 7) Thread Compound a) Thread compound requirements, unless otherwise specified in the individual Line Class, shall conform to the following: Temperatures up to 232°C: Teflon Tape Temperatures above 232 °C: Armite LED-PLATE NO. 250 Anti Seize Compound (Armite: Armite Laboratories) When thread compound is used, it should be applied to the male thread only.

JULY, 2005 NIOEC-SP-70-03(1)

5

In hydrogen services, graphite tape shall be used in place of PTFE (Teflon) tape. b) On joints which must be seal-welded, thread compound shall not be used.

7. INSTRUMENT IMPULSE LINE MATERIAL SPECIFICATION 7.1 Tubing In general, for services of ANSI flange class 300 and 600, and for the pipe line classes indicated in

the following Table 7.1, all instrument impulse lines, downstream of the first process isolating valve

shall be ½ inch OD, 316 SS seamless tubing with wall thickness of 0.065 inch minimum, and 316

Stainless Steel, bar stock double-ferrule compression type fittings. Byte type fittings are not

permitted.

INSTRUMENT ½ INCH TUBING MATERIAL SPECIFICATION

REV.

CLASS PIPE LINE CLASS

FITTING

* GENERAL MATERIAL

* SERVICE

ZA

A, AB, C CB

316 Stainless Steel , bar stock double-ferrule compression type

316 Stainless Steel, 0.065 inch wall thickness

Hydrocarbons, Caustic, in Hydrogen (to 5 Bars a)

ZB

AF,AM F,L,LA LAA,RA,SA CSH,SS,FC

316 Stainless Steel , bar stock double-ferrule compression type

316 Stainless Steel, 0.065 inch wall thickness

Liquid Sulphur Asphalt, Foul Condensate with or without Hydro- carbons, Hydro- carbons, Hydrogen (to 5 Bars-a) Steam, BFW, Condensate, Draft Gauge, Air- Utility, Instrument Water Plant, Cooling, Fire

Table 7.1 7.2 Pipe For the pipe line classes indicated in the following Table 7.2, for ANSI flange class of above 600# , or cases where the impulse lines are subject to physical expansion, impulse lines shall be ½ “ OD, seamless pipes. For service with pressure of greater than 40 Barg, fully butt-welded construction with heavy wall tubing or line pipe shall be provided.

JULY, 2005 NIOEC-SP-70-03(1)

6

INSTRUMENT PIPING MATERIAL SPECIFICATION

REV. ** CLASS

** PIPE LINE CLASS

FITTING RATING

* GENERAL MATERIAL

* SERVICE

ZC

AH,AV,CH, CMH,FCH FDH,FH GCH,GH,HCH HH,JH

6000# SCRD

Steel

Hydrogen (above 5 Bars-a) with or without Hydrocarbons, Chemical Injection

ZD AK 6000# Steel 93-98% Sulphuric Acid

ZE JCH,JIH JSH,HSH

6000# SCRD

316/347 Stainless steel

Hydrogen (above 5 Bars-a) with or with-out Hydrocarbons, Hot H2 Rich Reformer Gas.

ZF

AC,AD,AL AS,CC,CD CL,CS,HL CN,ASS

6000# SCRD

304/316 Stainless steel

Hydrocarbons, Rich Amine, Carbon Dioxide Rich Condensate compressor Lube and Seal Oil

ZG LB Sch 80 PVC Brine

ZJ LD

300# SCRD

Galvanized Steel Brass and Copper

Water-Domestic Air-Instrument, sub-Header, Branch Lines to Filter- Regulator

ZY

250# SCRD

Brass Copper

Control Instrument Air

ZZ

Instrument and Tubing Support

INSTR.

To be used for all Line Classes

*****

*****

*****

Stainless Steel Tube and Fittings

Steam Tracing

Table 7.2

NOTES: * For general reference only. Refer to General Notes and Material Classes for specific details. For Piping Material Reference shall be made to NIOEC-SP-50-4.

JULY, 2005 NIOEC-SP-70-03(1)

7

8. INSTRUMENT AIR SUPPLY PIPING Field instrument air piping shall be seamless galvanized steel, sealing of ends shall be Teflon compound, and fittings shall be according piping standards. Valves shall be brass, ball type, size ½ inch for each user.

9. INSTRUMENT AIR TUBING 9.1 Individual instrument air supply and pneumatic field transmission lines to and from instruments shall be PVC coated ¼" copper tubes unless otherwise specified (e.g.) stainless steel for corrosive atmosphere. 9.2 Where necessary for fast action of control valves ½ inch PVC coated copper tube or stainless tube will be used. 9.3 Material of air fittings and end connectors shall be brass in general; vinyl cap shall be supplied for protection fitting and connectors. Stainless-steel fitting shall be supplied for specific critical areas.

10. ANALYSER AND HOOK-UP TUBING 10.1 Analyser tubing shall be stainless steel with considering line pressure and temperature. 10.2 Tube fittings and connectors shall be stainless steel and high pressure with double ferrule. 10.3 Hook-up tubes shall be stainless steel, seamless with minimum 1.7 mm wall teak ness for line pressure up to 10 bars.

11. SUPPORTS Pipe stanchion for instrument shall be 2 inch schedule 80. Stud bolt/nuts shall be galvanized steel. Supports shall be painted according painting specification NIOEC-SP-80-2. Expansion bolts (roll bolts) shall be minimum 12 mm galvanized.

12. INSULATION & SEALING MATERIALS Sealing material for cable duct bank shall be Bentonite. Sealing material for air piping shall be Teflon compound.

13. TAG-NO AND NAME PLATE MATERIAL Name plate of instruments shall be stainless-steel plate. Tag number and identification band of instrument cables shall be stainless-steel tape. Wire for fixing tag-number to cables be stainless-steel.

JULY, 2005 NIOEC-SP-70-03(0)

14. APPENDIX I LINE CLASSES

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I I

SEQ.

NO.

REV

SIZE ITEM NAME NOTES DESCRIPTION REFERENCE NOTES

16.SPRAY SHIELD REQUIRED FOR ALL FLANGED JOINTS AND VALVE BONNETS IN CAUSTIC AND ACID SERVICES 57.VELOCITY SHALL BE LIMITED 10 8 FEET PER SECOND 58.CONCENTRATION AND TEMPERATURE SHALL BE LIMITED TO ZONE A OF THE SHELL CORROSION DATA: SURVEY “CAUSTIC SODA SERVICE CHART”

SERVICE SERVICE –SEE INDEX THIS SPECIFICATION SHALL BE USED FOR INSTRUMENT PIPING FOR LINE CLASSES:

A, AB, C & CB

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1 1/4 – 1 1/2 – ½ 1/2 – ½ 1/2 – ½ 1/2 – ½ 1/2 – 1/2 1/4 – 1 1/2

NEE NEE-SCR MAV MAV-FLG MAV-SCR MAV-SCR ADP PIP

16.57 50 16

SPECIAL PROVISIONS METER VALVES (GENERAL PURPOSE) NEEDLE VALVE 10000 SCRD STL H/JC 187-1 (FOR MONEL TRIM PROCESS LINE VALVE ONLY NEEDLE VA 10000 SCRD STL. MONEL TRIM MANIFOLD VALVES (USE AT ORIFICE FLANGE GENERAL PURPOSE-260� AND LOWER) MANIFOLD VA 6000” FLG STL 3 VA ASSY (USE AT ORIFICE FLANGE-FOR MONEL TRIM PROCESS LINE VALVE ONLY-260� AND LOWER) MANIF VA 6000” FLG STL MONEL TR 3VA ASSY (USE AT ONIFICE FLANGE-

GENERAL PURPOSE –261� AND HIGHER) MANIFOLD VALVE 1500” SCRD STL 3 VA ASSY (USE AT ORIFICE FLANGE-FOR MONEL TRIM PROCESS LINE VALVE ONLY-261� AND HIGHER) MANIF VA 1500” SCRD STL MONEL TR 3VA ASSY MANIFOLD VALVE ADAPTOR VERTICAL ADAPTOR 1500” SCRD A-G AM25 PIPE PIPE SCH 80 SMLS STL A53-B

GENERAL NOTE(1) MARSH 1900FF0 MARSH 1900 GENERAL NOTE(1) AGCO MMAVC AGCO MMAVC-50 AGCO M2HC AGCO M2HC-50 GREENWOOD GENERAL NOTE(2)

MATERIAL –STEEL TEMPERATURE RANGE:-30 THRU 400� PRESSURE RANGE: PER ANSI B16.5

CONSTRUCTION CORROSION ALLOWANCE CLASS PAGE

1-1/2 INCHES AND SMALLER SCREWED AND /OR SOCKET WELD NONE ZA 1 OF 3

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I II

SEQ.

NO.

REV

SIZE ITEM NAME NOTES

DESCRIPTION REFERENCE NOTES


A, AB, C, & CB

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1/2 1/4 – 1/2 1/4 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/4 – 1/2

ELL TEE CAP COU UNI PLG ADF-PF ADP-MF NIP-TBE NIP-TBE NIP-PBE NIP-TBE NIP-TBE NIP-ECC SWA-CTE SWA-CTS SWA-CTL SWA-CBE SWA-CTE SWA-CTS SWA-CTL SWA-CBE BLD

…PIPE FITTINGS… ELL 90 DEG 3000” SW STL A105 TEE 3000” SW STL A105 CAP 3000” SCRD STL A105 COUPLING 3000” SW STL A105 UNION 3000” SW STL A105 PLUG ROUND HEAD SCRD STL A105 ADAPTOR PE FPT STL ADAPTOR MPT FPT STL …PIPE FLANGES, BOLTS AND GASKETS … USE LINE CLASS MATERIALS …PIPE NIPPLES… NIPPLE XS STL A53-B TBE NIPPLE XS STL A53-B TBE NIPPLE SCH 80 STL A53-B PBE NIPPLE SCH 160 STL A53-B TBE NIPPLE SCH 160 STL A53-B TBE USE WITH MANIFOLD VALVE… NIPPLE-ECCENTRIC. STL TBE AGCO 2-2517C …SWAGE NIPPLE… SWAGE CONC XS STL A234 GR WPB TBE SWAGE CONC XS STL A234 GR WPB TSE SWAGE CONC XS STL A234 GR WPB TLE SWAGE CONC XS STL A234 GR WPB BBE SWAGE CONC SCH 160 STL A234 GR WPB TBE SWAGE CONC SCH 160 STL A234 GR WPB TSE SWAGE CONC SCH 160 STL A234 GR WPB TLE SWAGE CONC SCH 160 STL A234 GR WPB BBE …VENT PLUGS… (IN SERVICE 250� AND LOWER) PURGE VALVE 4000” SCRD 316 SS (IN SERVICE 251� AND HIGHER) USE PLUGGED METER VALVE

GENERAL NOTE(3) MILLS L531 MILLS L534 AGCO 2-2517C NUPRO

MATERIAL –STEEL TEMPERATURE RANGE:-30 THRU 400C PRESSURE RANGE: PER ANSI B16.5


1-1/2 INCHES AND SMALLER SCREWED AND /OR SOCKETWELD NONE ZA 2 OF 3

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I III

SEQ.

NO.

REV

SIZE ITEM NAME NOTE NO. DESCRIPTION REFERENCE NOTES


A, AB, C, & CB

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 - 1 1/2 1/4 - 1 1/2

PUL SPT SPT-P01 COV

…PULSATION DAMPENER… DAMPENER PULSATION 302 SS SCRD …SEAL POTS… (LIMITED TO 400� AT 42 BAR) POT SEAL SCH 80 SMLS STL 3-1/2 DDX 5-1/2 POT SEAL SCH 80 SMLS STL 4-1/2 DDX 14 …SPRAY SHIELD… COVER FOR 8OO” SCR/SW GLOBE VALVE BONNET ……CONSTRUCTION DETAILS …… (SEE GENERAL NOTES) SEAL WELDING--------------------------(4) PIPE BENDS ------------------------------(6) THREAD COMPOUND------------------(7)

CAMPBELL 1110C MILLS 93-354 MILLS 94-434 MILSHEFF



1-1/2 INCHES AND SMALLER SCREWED AND /OR SOCKETWELD NONE ZA 3 OF 3

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I IV

SEQ.

NO.

REV

SIZE ITEM NAME

NOTE NO. DESCRIPTION REFERENCE NOTES

16.SPRAY SHIELD REQUIRED FOR ALL FLANGED JOINTS AND VALVE BONNETS IN CAUSTIC AND ACID SERVICES 57.VELOCITY SHALL BE LIMITED 10 D FEET PEN SECOND 58.CONCENTRATION AND TEMPERATURE SHALL BE LIMITED TO ZONE A CP THE SHELL CORROSION DATA CURVEY CAUSTIC SODA SERVICE CHART


AF, AV, AH, F. L, LA, LF ,R ,S

& DRAFT GAUGE

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1 1/4 – 1 1/2 – 1/2 1/2 – 1/2 1/2 – 1/2 1/2 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2

NEE NEE-SCR MAV MAV-FLG MAV-SCR ADP PIP ELL TEE CAP UNI PLG

…METER VALVES… (GENERAL PURPOSE) NEEDLE VALVE 10000 SCRD STL H/JC 187-1 (LINE CLASSS AR ONLY) NEEDLE VALVE 10000 SCRD STL MONEL TRIM …METER VALVES… (USE AT ORIFICE FLANGE- GENERAL PURPOSE-LGOC AND LOWER) MANIFOLD VA 6000 FLG STL 3 VA ASSY (USE AT ORIFICE FLANGE- LINE CLASS OF ONLY) MANIF VA 6000 FLG STL MONEL TR 3 VA ASSY (USE AT ORIFICE FLANGE- STEAH LINES AND LINES 261C AND HIGHER) MANIF VA 1500 SCRD STL TR 3 VA ASSY …MANIFOLD VALVE ADAPTOR… VERTICAL ADAPTOR 1500 SCRD A-O AM25 …PIPE… PIPE SCH 00 SHLS STL A53-0 …PIPE FITTINGS… ELL 90 DEG 3000 SCRD STL AIOS TEE 3000 SCRD STL A105 CAP 3000 SCRD STL A105 UNION 3000 SCRD STL A105 PLUG ROUND HEAD SCRD STL A105 …PIPE FLANGES DOLTS AND GASKET USE LINE CLASS MATERIALS

GENERAL NOTE(1) MARSH 1900FF0 MARSH 1900 AGCO MMAVC AGCO MMAVC-50 AGCO M2HCV GENERAL NOTE(2) GENERAL NOTE(3)



1-1/2 INCHES AND SMALLER SCREWED NONE ZB 1 OF 3

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I V

SEQ.

NO.

REV SIZE ITEM

NAME NOTE NO. DESCRIPTION REFERENCE NOTES



& DRAFT GAUGE

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1/4 1/4 – 1/4 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/4 – 1/2 1/4 – 1/2 1/2 – 1/2

NIP-TBE NIP-TOE NIP-TBE NIP-TOE NIP-ECC SWA-CTE SWA-CTS SWA-CTL SWA-CTE SWA-CTS SWA-CTL BLD PUL SIP

…PIPE FITTINGS… NIPPLE XS STL A53-B TBE NIPPLE XS STL A53-B TOE NIPPLE SCH 160 STL A53-B TBE NIPPLE SCH 160 STL A53-B TOE (USE WITH MANIFOLD VALVE) NIPPLE-ECCENTRIC. STL TBE AGCO 2-2517C …SWAGE NIPPLES… SWAGE CONC XS STL A234 GR WPB TBE SWAGE CONC XS STL A234 GR WPB TSB SWAGE CONC XS STL A234 GR WPB TLE SWAGE CONC SCH 160 STL A234 GR WPB TBE SWAGE CONC SCH 160 STL A234 GR WPB TSE SWAGE CONC SCH 160 STL A234 GR WPB TLE …VENT PLUGS… (IN SERVICE 250� AND LOWER) PURGE VALVE 4000” SCRD 316 SS (IN SERVICE 250C AND HIGHER) USE PLUGGED METER VALVE …PULSATION DAMPENER… DAMPENER PULSATION 302 SS SCRD …SIPHON… SIPHON GAGE STL W/SS BARREL & INSERT

AGCO 2-2517C NUPRO CAMPBELL 1110C GREENWOOD “CT-7 MATERIAL –STEEL

TEMPERATURE RANGE:-30 THRU 400C PRESSURE RANGE: PER ANSI B16.5



JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I VI

SEQ.

NO.

REV

SIZE ITEM NAME




& DRAFT GAUGE

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1/4 1/4 – 1/4 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/4 – 1/2 1/4 – 1/2 1/2 – 1/2

SPT SPT-POT CPT

…SEAL POTS… (LIMITED TO 400� AT 42 BAR) POT SEAL SCH 80 SMLS STL 3-1/2 ODX 3-1/2 POT SEAL SCH 80 SMLS STL 4-1/2 ODX 14 …CONDENSATE POT … (LIMITED TO 400� AT 42 BAR) POT COND SCH 80 SMLS STL 4-1/2 00X 11 ……CONSTRUCTION DETAILS …… (SEE GENERAL NOTES) SEAL WELDING ---------------------------(4) PIPE BENDS--------------------------------(5 ) THREAD COMPOUND-------------------( )

MILLS 93-354 MILLS 94-434 MILLS 93-354




JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I VII

SEQ.

NO.

REV

SIZE ITEM NAME


23. AS THE PARTIAL PRESSURE OF HYDROGEN INCREASES THE PERMISSION TEMPERATURE LIMIT WILL DECREASE PER API-941


AH, CH, CMH, CN, FCH, FDH FH, GCH, GH, HCH, HH, & JH

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1 1/2 1/2 – 1/2 1/2 – 1/2 1/2 – 1/2 1/4 – 1/4 1/2 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2

GLO MAV MAV-SOR AOP PIP PIP ELL TEE CAP COU PLG ADP-PF ADP-MF BUS UNI UNI-FLG

23 …SPECIAL PROVISION… …METER VALVE… GLOBE 2500” SCRD STL FG TRIM WAASB PKD …MANIFOLD VALVES… (USE AT ORIFICE FLANGE-260� AND LOWER) MANIFOLD VA 6000” FLG STL 3 VA ASSY (USE AT ORIFICE FLANGE-261� AND HIGHER) MANIFOLD 1500” SCRD STL 3 VA ASSY …MANIFOLD VALVE ADAPTOR… VERTICAL ADAPTOR 1500” SCRD A - O AM25 …PIPES… PIP SCH 80 SMLS STL A53-B PIP SCH 160 SMLS STL A53-B …PIPE FITTING… ELL 90 DEG 6000” SCRD STL A105 TEE 6000” SCRD STL A105 CAP 6000” SCRD STL A105 COUPLING 6000” SCRD STL A105 PLUG ROUND HEAD SCRD STL A105 ADAPTER PE X FPT STL ADAPTER MPT X FPT STL BUSHING 6000” HEX HEAD SCR STL, A105 UNION 6000 SCRD STL A105 UNION FLANGE 1500” SW STL T & G FACE …PIPE FLANGES BOLTS AND GASKETS USE LINE CLASS MATERIALS

GENERAL NOTE(1) EDWARD 952 GENERAL NOTE(1) AGCO M4AVC AGCO M2HC GREENWOOD GENERAL NOTE(2) GENERAL NOTE(3) MILLS L531 MILLS L532 CLASSES HCH. HH & JH ONLY



1-1/2 INCHES AND SMALLER SCREWED NONE ZC 1 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I VIII

SEQ.

NO.

REV

SIZE ITEM NAME



AH, CH, CMH, CN, FCH, FDH FH, GCH, GH, HCH, HH, & JH

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1/4 1/4 – 1/4 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/4 – 1/2

NIP-TBE NIP-TOE NIP-TBE NIP-TOE NIP SWA-CTE SWA-CTS SWA-CTL SWA-CTE SWA-CTS SWA-CTL PUL SPT SPT-POT

…PIPE FITTINGS… NIPPLE XS STL A53-B TBE NIPPLE XS STL A53-B TOE NIPPLE SCH 160 STL A53-B TBE NIPPLE SCH 160 STL A53-B TOE (USE WITH MANIFOLD VALVE): NIPPLE-ECCENTRIC STD TBE AGCO 2-2517C …SWAGE NIPPLES… SWAGE CONC XS STL A234 GR WPB TBR SWAGE CONC XS STL A234 GR WPB TSB SWAGE CONC XS STL A234 GR WPB TLE SWAGE CONC SCH 160 STL A234 GR WPB TBE SWAGE CONC SCH 160 STL A234 GR WPB TSE SWAGE CONC SCH 160 STL A234 GR WPB TLE …VENT PLUG… USE PLUGGED METER VALVE …PULSATION DAMPENER DAMPENER PULSATION 302 SS SCRD …SEAL POTS… (LIMITED TO 400� AT 42 BAR) POT SEAL SCH 80 SMLS STL 3-1/2 ODX 5-1/2 POT SEAL SCH 80 SMLS STL 4-1/2 ODX 14 ……CONSTRUCTION DETAILS …… (SEE GENERAL NOTES) SEAL WELDING ---------------------------(4) PIPE BENDS--------------------------------( 6) THREAD COMPOUND-------------------( 7)

AGCO 2-2317C CAMPBELL 1110C MILLS 93-354 MILLS 94-434

MATERIAL –STEEL TEMPERATURE RANGE:-30 THRU 400� PRESSURE RANGE: PER ANSI B 16.5


1-1/2 INCHES AND SMALLER SCREWED NONE ZC 2 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I IX

SEQ.

NO.

REV

SIZE ITEM NAME


16. SPRAY SHIELD REQUIRED FOR ALL FLANGED POINTS AND VALVE

BONNETS IN CAUSTIC AND ACID SERVICES

48. OTHER TEMPERATURE LIMITS AND CONCENTRATIONS MAY BE USED IF LIMITED TO ZONE 4 AND 0 OF

THE SHELL CORROSION DATA SURVEY “SULFURIC ACID GRAPH

55. VELOCITY SHALL BE LIMITED TO 5 FEET PER SECOND


AK

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1/2 1/2 – 1/2 1/2 – 1/2 1/4 – 1/4 1/2 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2

GLO MAV ADP PIP PIP ELL TEE CAP COU UNI PLG ADP-PF ADP-MF

16.40 55 16

…SPECIAL PROVISIONS… …METER VALVE… GLOBE 150” SCRD ALLOY 20 …MANIFOLD VALVE… (USE AT ORIFICE FLANGE) MANIFOLD VA 6000” FLG 316 SS 3 VA ASSY …MANIFOLD VALVE ADAPTOR… VERTICAL ADAPTOR 1500” SCRD A-O AM2S …PIPES… PIPE SCH 80 SMLS STL A53-B PIPE SCH 160 SMLS STL A53-B …PIPE FITTINGS ELL 90 DEG 6000” SW STL A105 TEE 6000” SW STL A105 CAP 6000” SW STL A105 COUPLING 6000” SW STL A105 UNION 6000” SW STL A105 PLUG ROUND HEAD SCRD STL A105 ADAPTER PE X FPT STL ADAPTER MPI X FPT STL …PIPE FLANGES BOLTS AND GASKETS… USE LINE CLASS MATERIALS

GENERAL NOTE(1) ALOYCO 310 GENERAL NOTE(1) AGCO M4AYS GREENWOOD GENERAL NOTE(2) GENERAL NOTE(3) MILLS L531 MILLS L532 MATERIAL –STEEL

TEMPERATURE RANGE:-30 THRU 400C PRESSURE RANGE: PER ANSI B16.5


1-1/2 INCHES AND SMALLER SCREWED AND /OR SOCKETWELD NONE ZD 1 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I X

SEQ.

NO.

REV

SIZE ITEM NAME



AK

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/2 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1/2 1/4 – 1 1/2

NIP-PBE NIP-TBE NIP-TOE NIP-ECC SWA-CTE SWA-CTS SWA-CTL SWA-CBE PUL SPT SPT-POT COV

…PIPE FITTINGS… NIPPLE SCH 00 STL A53-B PBE NIPPLE XS STL A53-B TDE NIPPLE XS STL A53-B TOE (USE WITH MANIFOLD VALVE): NIPPLE-ECC-316 SS TBE AGCO 2-2517S …SWAGE NIPPLES… SWAGE CONC XS STL A234 GR WPB TBE SWAGE CONC XS STL A234 GR WPB TSE SWAGE CONC XS STL A234 GR WPB TLE SWAGE CONC XS STL A234 GR WPB BBE …VENT PLUG… USE PLUGGED METER VALVE …PULSATION DAMPENER… DAMPENER PULSATION STL SCRD …SEAL POTS… POT SEAL SCH 80 SMLS STL 3-1/2 ODX 5-1/2 POT SEAL SCH 80 SMLS STL 4-1/2 ODX 14 …SPRAY SHIELD… COVER FOR BOC SCR/SW GLOBE VALVE BONNET ……CONSTRUCTION DETAILS …… (SEE GENERAL NOTES) SEAL WELDING ---------------------------(4) PIPE BENDS--------------------------------( 6) THREAD COMPOUND-------------------( 7)

AGCO 2-2517 CAMPBELL 11105 MILLS 93-S54 MILLS 94-434 HILSHELL

MATERIAL –STEEL TEMPERATURE RANGE:-30 THRU 400� PRESSURE RANGE: PER ANSI B16.5


1-1/2 INCHES AND SMALLER SCREWED AND /OR SOCKETWELD NONE ZD 2 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XI

SEQ.

NO.

REV

SIZE ITEM NAME


23. AS THE PARTIAL PRESSURE OF HYDROGEN INCREASES, THE

PERMISSIBLE TEMPERATURE LIMIT WILL DECREASE PER API-941

26. TYPE 321 STAINLESS STEEL MAY BE USED IN LIEU OF TYPE 347


HSH, JCH, JIH & JSH

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1 1/2 1/2 – 1/2 1/2 – 1/2 1/2 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2

GLO MAV MAV-SCR ADP PIP ELL TEE CAP COU UNI PLG BUS

23.26 …SPECIAL PROVISIONS… …METER VALVE… GLOBE 2500” SCRD 316 SS …MANIFOLD VALVES… (USE AT ORIFICE FLANGE 260� AND LOWER) MANIFOLD VA 6000” FLG 316 S 3VA ASSY (USE AT ORIFICE FLANGE 251� AND HIGHER) MANIFOLD 1500 SCRD 316SS 3VA ASSY …MANIFLOLD VALVE ADAPTOR… VERTICAL ADAPTOR 1500” SCRD A-O AM2S …PIPE PIPE SCH 160 SMLS 347 SS A312 …PIPE FITTINGS… ELL 90 DEG 5000 SCRD 347 SS TEE 6000” SCRD 347 SS CAP 6000” SCRD 347 SS COUPLING 6000” SCRD 347 SS UNION FLANGE 1500” SW 347 SS T & G FACE PLUG ROUND HEAD SCRD 347 SS BUSHING 6000” HEX HEAD SCRD 347 SS …PIPE FLANGES BOLTS AND GASKETS… USE LINE CLASS MATERIALS

GENERAL NOTE(1) EDWARD 4952 GENERAL NOTE(1) AGCO M4AVS AGCO M2HS GREENWOOD GENERAL NOTE(2) GENERAL NOTE(3) VOCT SW 2701 NUPRO

METERIAL-316/347 STAINLESS STEEL MAXIMUM TEMPERATURE: DIGC PRESSURE RANGE: PER ANSI B 16.5


1-1/2 INCHES AND SMALLER SCREWED NONE ZE 1 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XII

SEQ. NO

.

REV

SIZE ITEM NAME



HSH, JCH JIH, & JSH

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1/4 1/4 – 1/4 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/4 – 1/2 1/2 – 1/2

NIP-TBE NIP-TOE NIP-TBE NIP-TOE NIP-ECC SWA-CTE SWA-CTS SWA-CTL SWA-CTE SWA-CTS SWA-CTL PUL SIP SPT SPT-POT

…PIPE FITTINGS… NIPPLE SCH 80S 347 SS TBE NIPPLE SCH 80S 347 SS TOE NIPPLE XXS 347 SS TBE NIPPLE XXS 347 SS TOE (USE WITH MANIFOLD VALVE): NIPPLE-DCC-316 SS TBE AGCO 2-2517S …SWAGE HIPPLES SWAGE CONC SCH 80S 347 SS TBE SWAGE CONC SCH 80S 347 SS TSE SWAGE CONC SCH 80S 347 SS TLE SWAGE CONC XXS 347 SS TBE SWAGE CONC XXS 347 SS TSE SWAGE CONC XXS 347 SS TLE …VENT PLUGS… USE PLUGGED METER VALVE …PULSATION DAMPENER… DAMPENER PULSATION 302 SS SCRD …SIPHON… SIPHON GAGE STL W/SS BARREL INSERT …SEAL POTS… (LIMITED TO 400C AT 42 BAR) POT SEAL SCH DOS 304 SS 3-1/2 OD X 5-1/2 POT SEAL SCH DOS 304 SS 3-1/2 OD X 14 ……CONSTRUCTION DETAILS …… (SEE GENERAL NOTES) SEAL WELDING ---------------------------(4) PIPE BENDS--------------------------------( 6) THREAD COMPOUND-------------------( 7)

AGCO 2-2517 CAMPBELL 1110C GREENWOOD CT-7 MILLS 93-354 MILLS 93-354

METERIAL-316/347 STAINLESS STEEL MAXIMUM TEMPERATURE: DIGC PRESSURE RANGE: PER ANSI B16.5


1-1/2 INCHES AND SMALLER SCREWED NONE ZE 2 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XIII

SEQ.

NO.

REV

SIZE ITEM NAME



AC. AD. AL. AS. CC. CD. CL. CS. & HL

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1 1/2 1/2 – 1/2 1/2 – 1/2 1/2 – 1/2 1/4 – 1/4 1/2 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2

NEE MAV MAV-SCR ADP PIP PIP ELL TEE CAP COU PLG UNI UNI-FLG BUS

…METER VALVE… NEEDLE VA 6000” SCRD 316 SS W’JC 107-1 …MANIFOLD VALVES… (USE AT ORIFICE FLANGE 260� AND LOWER) MANIFOLD VA 6000” FLG 316 SS 3 VA ASSY (USE AT ORIFICE FLANGE 261� AND HIGHER) MANIFOLD 1500” SCRD 316 SS 3 VA ASSY …MANIFOLD VALVE ADAPTOR… VERTICAL ADAPTOR 1500” SCRD A-O AM25 …PIPE PIPE SCH 80S SMLS 304 SS A312 PIPE SCH 160 SMLS 304 SS A312 …PIPE FITTINGS… ELL 90 DEG 6000” SCRD 304 SS TEE 6000 ” SCRD 304 SS CAP 6000 ” SCRD 304 SS COUPLING 6000 ” SCRD 304 SS UNION FLANGE 1500 ” SW 304 SS T & G FACE PLUG ROUND HEAD SCRD 304 SS BUSHING 6000 HEX HEAD SCRD 304 SS …PIPE FLANGES BOLTS AND GASKETS… USE LINE CLASS MATERIALS

GENERAL NOTE(1) MARSH 1936FFG GENERAL NOTE(1) AGCO M4AVS AGCO M2HS GREENWOOD GENERAL NOTE(2) GENERAL NOTE(3) CLASS HL ONLY METERIAL-304/316

STAINLESS STEEL MAXIMUM TEMPERATURE: -30 THRU 310C PRESSURE RANGE: PER ANSI B16.5


1-1/2 INCHES AND SMALLER SCREWED NONE ZF 1 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XIV

SEQ.

NO.

REV

SIZE ITEM NAME



AC. AD. AL. AS. CC. CD. CL. CS. & HL

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1/4 1/4 – 1/4 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/4 – 1/2 1/4 – 1/2

NIP-TBE NIP-TOE NIP-TBE NIP-TOE NIP-ECC SWA-CTE SWA-CTS SWA-CTL SWA-CTE SWA-CTS SWA-CTL BLD PUL SPT SPT-POT

…PIPE FITTINGS… NIPPLE XS, 304 SS TBE NIPPLE XS, 304 SS TOE NIPPLE SCH 160 304 SS TBE NIPPLE SCH 160 304 SS TOE (USE WITH MANIFOLD VALVE): NIPPLE-ECCENTRIC-316 SS TDE AGCO 2-2317C …SWAGE NIPPLES… SWAGE CONC XS 304 SS TBE SWAGE CONC XS 304 SS TSE SWAGE CONC XS 304 SS TLE SWAGE CONC SCH 160 304 SS TBE SWAGE CONC SCH 160 304 SS TSE SWAGE CONC SCH 160 304 SS TLE …VENT PLUG… (IN SERVICE 250� AND LOWER) PURGE VALVE 4000” SCRD 316 SS (IN SERVICE 251� AND HIGHER) USE PLUGGED METER VALVE …PULSATION DAMPENER DAMPENER PULSATION 302 SS SCRD …SEAL POTS… (LIMITED TO 400� AT 42 BAR) POT SEAL SCH 80S 304 SS 3-1/2 ODX 3-1/2 POT SEAL SCH 80S 304 SS 4-1/2 ODX 14 ……CONSTRUCTION DETAILS …… (SEE GENERAL NOTES) SEAL WELDING ---------------------------(4) PIPE BENDS--------------------------------( 6) THREAD COMPOUND-------------------( 7)

AGCO 2-2517 NUPRO CAMPDELL 1110C MILLS 93-354 MILLS 93-354

METERIAL-304/316 STAINLESS STEEL MAXIMUM TEMPERATURE: -30 THRU 310C PRESSURE RANGE: PER ANSI B16.5


1-1/2 INCHES AND SMALLER SCREWED NONE ZF 2 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XV

SEQ.

NO.

REV

SIZE ITEM NAME


44. LOWER TEMPERATURE WILL CAUSE MATERIAL TO BECOME BRITTLE 709. WHERE ADDITIONAL MECHANICAL STRENGTH IS DEEMED NECESSARY

FILLET WELDING MAY BE DONE


LB

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/2 – 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2 1/2 – 1 1/2

DPH PIP ELL 45L TEE CAP CAP-SW COU COU-FSW BUS BUS-SCR UNI NIP-PBE CEM

44 709

…SPECIAL PROVISIONS… … VALVE… DIAPHRAGM 150 ” SW PVC-NI …PIPE… PIPE SCH 80 SMLS PVC PE …PIPE FITTINGS… ELL 90 DEG SCH 80 PVC SW ELL 45 DEG SCH 80 PVC SW TEE SCH 80 PVC SW CAP SCH 80 PVC SCRD CAP SCH 80 PVC SW COUPLING SCH 80 PVC SW COUPLING REDUCING SCH 80 PVC SW REDUCING BUSHING SCH 80 PVC SW BUSHING REDUCING SCH 80 PVC SW X SCRD UNION SCH 80 PVC SW …PIPE FLANGES BOLTS AND GASKETS… USE LINE CLASS MATERIALS …PIPE NIPPLE … NIPPLE SCH 80 PVC PBE …JOINTS… SOLVENT CEMENT FOR PVC ……CONSTRUCTION DETAILS …… (SEE GENERAL NOTES) SEAL WELDING -------------------------- -NONE PIPE BENDS-------------------------------- NONE THREAD COMPOUND------------------ NONE

GENERAL NOTE(1) MCCANNA P510-3 GENERAL NOTE(2) CHEMTROL GENERAL NOTE(2) CHEMTROL CHEMTROL CHEMTROL CHEMTROL CHEMTROL CHEMTROL CHEMTROL CHEMTROL CHEMTROL CHEMTROL CHEMTROL CHEMTROL CHEMTROL

MATERIAL –POLYVINYL CHLORIDE (NORMAL IMPACT) MAXIMUM TEMPERATURE: 50� MAXIMUM PRESSURE: 8.0 BARS


1-1/2 INCHES AND SMALLER SOCKET CEMENTED EXCEPT AS NOTED NONE ZG 1 OF 1

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XVI

SEQ.

NO.

REV

SIZE ITEM NAME



LD, INSTRUMENT AIR SUB-HEADER, BRANCH LINES TO FILTER-REGULATORS

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/2 –1 1/2 1/4 –1 1/2 1/4 – 1/4 3/8 – 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2 1/8 – 1 1/2

GAT PIP TUB TUB ELL 45L TEE COU UNI BUS PLG MTC FTC MTE FTE TTT TTM TTF FTT BKU TPL --- ---

…METER VALVE… GATE 125# SCRD BRONZE …PIPE… PIPE SCH 40 SMLS STL A53-B GALV TLC …TUBING… TUBING SMLS COPPER .030 WALL B68 TUBING SMLS COPPER .032 WALL B68 …PIPE FITTINGS… ELL 90 DEG 300# SCRD GALV M1 A197 ELL 45 DEG 300# SCRD GALV M1 A197 TEE 300# SCRD GALV M1 A197 COUPLING 300# SCRD GALV M1 A197 UNION 250# SCRD GALV M1 A197 BUSHING HEX HEAD SCRD GALV M1 A197 PLUG ROUND HEAD SCRD GALV STL A181 OR 1 …TUBING FITTINGS… MALE TUBE CONN BRASS.T x MPT FEMALE TUBE CONN BRASS.T x FPT MALE ELBOW BRASS. T x MPT FEMALE ELBOW BRASS. T x FPT TEE ALL TUBE BRASS. T x T x T TEE MPT BRANCH BRASS. T x T x MPT TEE FPT BRANCH BRASS. T x T x FPT TUBING UNION ALL TUBE BRASS BULKHEAD UNION ALL TUBE BRASS TUBING PLUG BRASS FRONT FERRULE BRASS BACK FERRULE BRASS

GENERAL NOTE(1) CRANE 420-WB GENERAL NOTE(1) GENERAL NOTE(3) SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK

MATERIAL –GALVANIZED STEEL BRASS AND COPPER MAXIMUM TEMPERATURE: 65C MAXIMUM PRESSURE: 10.3 BARS


1-1/2 INCHES AND SMALLER SCREWED AND /OR COMPRESSION TYPE TUBE NONE ZJ 1 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XVII

SEQ.

NO.

REV

SIZE ITEM NAME



LD, INSTRUMENT AIR SUB-HEADER, BRANCH LINES TO FILTER-REGULATORS

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 1 1/2 1/4 – 1 1/2 1/4 – 1 1/2

NIP-TBE SWA-GTE PUL

…PIPE NIPPLE… NIPPLE XS GALV STL A53-B TBE …SWAGE NIPPLE… SWAGE CONC XS CALV STL A234 GR WPB TBE …PULSATICN DAMPENER… DAMPENER PULSATION BRASS SCRD ……CONSTRUCTION DETAILS …… (SEE GENERAL NOTES) SEAL WELDING -------------------------- -NONE TUBING BENDS----------------------------(5) PIPE BENDS-------------------------------- NONE THREAD COMPOUND------------------ (7)

CAMPBELL 1110B

MATERIAL –GALVANIZED STEEL BRASS AND COPPER MAXIMUM TEMPERATURE: 65C MAXIMUM PRESSURE: 10.3 BARS


1-1/2 INCHES AND SMALLER SCREWED AND /OR COMPRESSION TYPE TUBE NONE ZJ 2 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XVIII

SEQ.

NO.

REV

SIZE ITEM NAME


SERVICE SERVICE –SEE INDEX THIS SPECIFICATION SHALL BE USED FOR INSTRUMENT PIPING FOR

CONTROL INSTRUMENT AIR ONLY

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/4 – 2 1/4 – 1/4 1/4 – 1 1/4 – 1/4 1/4 – 1/4 2 – 37 1/4 – 2 1/4 – 2 1/4 – 2 1/4 – 2 1/4 – 2 1/8 – 2

GAT GLO PIP TUB-POL TUB BUN ELL TEE COU UNI PLG DUS

…METER VALVE… (AT CONTROL PANEL FITLER-REG STATIONS) GATE 150# SCRD BRONZE (AT INDIVIDUAL INSTRUMENTS) GLOBE 100# SCRD BRASS …PIPE… PIPE EXTRA HEAVY SMLS BRASS B43 T & C …TUBINGS… (FOR SINGLE LEADS IN CONTROL PANELS OR INDOOR MOUNTED RACKS) TUBING POLYETHYLENE .040 WALL (FOR SINGLE LEADS IN FIELD) TUBING SMLS COPPER .030 WALL PE COATED …MULTITUBE BUNDLE… TUBG BUN W/ARMR 1/4 OD X .040 POLY TUBES …PIPE FITTINGS… ELL 90 DEG 250# SCRD BRASS B61 TEE 250# SCRD BRASS B61 COUPLING 250# SCRD BRASS B61 UNION 300# SCRD BRASS B61 PLUG GOUARE HEAD SCRD BRASS B61 BUSHING HEX HEAD SCRD BRASS B61

GENERAL NOTE(1) CRANE 431 G.W.DAHL DEML-G GENERAL NOTE(2) POLY-FLO 44-P DKOFLEX PLO GENERAL NOTE(3)

MATERIAL –BRASS COPPER ,AND POLYETHYLENE MAXIMUM TEMPERATURE: 95C MAXIMUM PRESSURE: 8.5 BARS


2 INCHES AND SMALLER-SCREWED: AND/OR COMPRESSION TYPE TUBE NONE ZY 1 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XIX

SEQ. NO

.

REV

SIZE ITEM NAME


SERVICE SERVICE –SEE INDEX THIS SPECIFICATION SHALL BE USED FOR INSTRUMENT PIPING FOR

CONTROL INSTRUMENT AIR ONLY

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/8 - 1 1/4 –1 1/2 1/4 – 1/4 1/2 – 1/2

MTC FTC MTE FTE TTT TTM TTF FTT BKU TPL UNE TRD --- --- NIP-TBE VFO VFO

…TUBING FITTINGS MALE TUBE CONN BRASS T x MPT FEMALE TUBE CONN BRASS T x FPT MALE BLDOW BRASS T x MPT FEMALE BLDOW BRASS T x FPT TEE ALL TUBE BRASS T x T x T TEE MPT BRANCH BRASS T x T x MRT TEE FPT BRANCH BRASS T x T x FRT TUBING UNION ALL TUBE BRASS BULKHEAD UNION ALL TUBE BRASS TUBING PLUG BRASS UNION BLDOW ALL TUBE BRASS TUBING REDUCER BRASS T x T FRONT FERRULE BRASS BACK FERULE BRASS …PIPE NIPPLE… NIPPLE XS RED BRASS 843 TBE …BUG-PROOF VENTS… VENT FTG BUG PROOF ANGLE PAT 1/4 FPT VENT FTG BUG PROOF ANGLE PAT 1/2 FPT …TAPE… (WRAP ALL TUBE FITTINGS AND EXPOSED TUBING) TAPE ALL-WEATHER VINYL-PLASTIC ELECT ……CONSTRUCTION DETAILS ……

(SEE GENERAL NOTES) SEAL WELDING ---------------------------NONE TUBING BENDS: SIMGLE TUBE------(5) MULTITUBE---------U?? MANUFACTURERS STANDARD BENDING RADIUS PIPE BBENDS--------------------------------NONE THREAD COMPOUND-------------------( 7)

SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK SWAGELOK FISHER Y602-13 FISHER Y602-7 SCOTCH 88

MATERIAL –BRASS COPPER ,AND POLYETHYLENE MAXIMUM TEMPERATURE: 95C MAXIMUM PRESSURE: 8.5 BARS


2 INCHES AND SMALLER-SCREWED: AND/OR COMPRESSION TYPE TUBE NONE ZY 2 OF 2

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XX

SEQ.

NO.

REV

SIZE ITEM NAME


SERVICE SERVICE –SEE INDEX THIS SPECIFICATION SHALL BE USED FOR :

INSTRUMENT &

TUBING SUPPORT ONLY

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1 - 8 1 - 8 2 – 2 4 – 4 6 – 6 1 - 96 6 - 6 9 - 9 1 - 2 2 1/2 - 3 3/8 – 3/4 3/8 – 12 1/2 – 12 3/8 - 12

ANG BAR CNL CNL CNL NIP-TBE PLT PLT PLT PIP PIP SHL BOL BOL-U BOL-M

……INSTRUMENT SUPPORT …… … ANGLE … ANGLE CS 1/4 THICK … FLATBAR … FLATBAR CS 1/4 THICK … CHANNELS … CHANNEL CS 2 INCH 1.70” PER FT CHANNEL CS 4 INCH 7.25” PER FT CHANNEL CS 6 INCH 0.2” PER FT … PLATES … PLATE CS 1/4 THICK PLATE CS 6 X 6 X 1/4 THK W/1/2 HOLES PLATE CS 9 X 9 X 1/2 THK W/5/8 HOLES … PIPES FOR PEDESTAL … PIPE SCH 80 SMLS STL A53-B PIPE SCH 40 SMLS STL A53-B … PHILLIPS SHELL … SMELL ALLOY STL W/EXPANDER PLUG … BOLTS … STUD-BOLT CHROME-MOLY A193 GRADE B7 U-BOLT MACHINE BOLT STEEL A307 GRADE B

PHILLIPS

INSTRUMENT & TUBING SUPPORT


NONE ZZ 1 OF 3

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXI

SEQ.

NO.

REV

SIZE ITEM NAME



INSTRUMENT &

TUBING SUPPORT ONLY

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1 -3 1 -3 1/8 1 1/2 –12 1/8 -12

UNI SWA-CTE TCP PCP UST UST-MUL SNT BOL BOL JBX JBX-BOX JBX-BOX

…UNION AND SWAGE… UNION 250# SCRD M1 A197 SWAGE CONC STD WT STL A234 GR WPB TBE

……TUBING SUPPORT ……

…TUBING CLAMP… CLAMP TUBING ONE HOLE GALV STL …PIPE CLAMP… CLAMP PIPE ELECTRO-GALV STL W/BOLT & NUT …CHANNELS… (SINGLE) UNISTRUT P-1000 STL 12 GA GREENAMEL FIN (MULTIPLE) UNISTRUT P-1001 STL 12 GA GREENAMEL FIN …SPRING NUT… NUT SPRING STL …CAP SCREWS AND NUTS… (FOR MOUNTING FILTER-FEGULATOR) CAP SCREW HEX HEAD W/LOCK WASHER & NUT (OTHERS) CAP SCREW HEX HEAD STL … JUNCTION DOXES… BOX JUNCTION 14 GA STL 10 X 12 X 6 BOX JUNCTION 14 GA STL 10 X 18 X 6 BOX JUNCTION 14 GA STL 24 X 18 X 6

UNISTRUT P-7008 UNISTRUT P-2024 UNISTRUT P-1000 UNISTRUT P-1001 UNISTRUT P-1006 WINSTON 1300 SE WINSTON 1300 SE WINSTON 1300 SE



NONE ZZ 2 OF 3

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXII

SEQ.

NO.

REV

SIZE ITEM NAME



INSTRUMENT &

TUBING SUPPORT ONLY

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

1 - 3 3/8 1 - 3 3/8 1 - 3 3/8 1 - 3 3/8 1 - 3 3/8 1 - 3 3/8 1/2 - 3 1/2 - 3 1/2 - 3 1/2 - 3 1/2 - 3

GMT KIT RWY RCN RFE RUR RFT CLP RVT PHN ——— ——— ——— ——— ——— ———

… ENTRY GROMMET … GROMMET ENTRY NEORPENE W/SS CLAMP … BANDING KIT … BAND KIT GALV STL, W/CLIPS, RATCH & PINS …… RACEWAY AND FITTINGS …… …RACEWAY … RACEWAY W/OUT CLIPS 18 GA GAEV STL … RACEWAY FITTINGS … CONNECTOR RACEWAY FLAT GALV STL W/RIVETS CONNECTOR RACEWAY 90 DEG FLAT STL W/RIVETS CONNECTOR RACEWAY UNIV RISER STL W/RIVETS CONNECTOR RACEWAY TEE FLAT GAL STL W/RIVETS CLIP PUSM STAINLESS STEEL RIVET DRIVE 1/4” STL SCREW, PAN HEAD W/NUT 6-32 X 1 INCH:

……CONDUIT AND FITTINGS …… … CONDUIT … CONDUIT RIGID GALVANIZED STEEL … CONDUIT FITTINGS … COUPLING RIGID CONDUIT GALV STEEL ELL 90 DEG 3G IN RAD RIGID CONDUTT GA ST HUB CONDUIT THREADED ZING ELL 90 DEG 3G IN RAD RIGID CONDUTT GA ST … TAPE … TAPE THREAD SEALING TEFLON

DEKORON 1500 P-W 9999-0904-0 P-W 2501-0016 P-W 2501-0016-1 P-W 2501-0016-9 P-W 2501-0016-9 P-W 2501-0016-2 P-W DS-9004 P-W DS-0500-1 ROME CABLE ROME CABLE HYERS ST1-ST2 ROME CABLE W.S. SHAMBAN



NONE ZZ 3 OF 3

70151

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXIII

SEQ.

NO.

REV

SIZE ITEM NAME


SERVICE SERVICE –SEE INDEX THIS SPECIFICATION SHALL BE USED FOR

CONTROL SYSTEM ENGINEERING INSTRUMENT ITEMS ONLY

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

TI-50C TII-20C TI-100 TI-200 TI-300 TI-450 TI-500 TW-50 TW-01X TW-01 TW-02 TW-03 TW-03R TW-03X TW-04 TW-04X TW-05 TW-05X TW-06 TW-06R TW-09 TW-015 TW-025

712 ……THERMOMETERS …… (TMERMOMETER STEM LENGTH TO BE LISTED IN THE SIZE COLUMN OF THE MATERIAL TAKE-OFF DATA SHEET) 01-METALLIC THERMOMETER ADJUST. SEALED 01-METALLIC THERMOMETER ADJUST. SEALED 01-METALLIC THERMOMETER ADJUST. SEALED 01-METALLIC THERMOMETER ADJUST. SEALED 01-METALLIC THERMOMETER ADJUST. SEALED 01-METALLIC THERMOMETER ADJUST. SEALED 01-METALLIC THERMOMETER ADJUST. SEALED …… THERMOWELLS …… (THERMOWELL U DIMENSION TO BE LISTED IN THE SIZE COLUMN OF THE MATERIAL TAKE-OFF DATA SHEET) THERMOWELL 316 SS 1 INCH MPT THERMOWELL 304 SS 1-1/2 150 # RFSP FLO THERMOWELL 304 SS 1-1/2 150 # RF FLO THERMOWELL 304 SS 1-1/2 INCH NPT MPT THERMOWELL 304 SS 1-1/2 300 # RF SS FLO THERMOWELL 304 SS 1-1/2 300 # RJ SS FLO THERMOWELL 304 SS 1-1/2 300 # RFSP SS FLO THERMOWELL 304 SS 2 INCH 150# RF FLO THERMOWELL 304 SS 2 INCH 150# RFSP FLO THERMOWELL 304 SS 2 INCH 300# RF FLO THERMOWELL 304 SS 2 INCH 300# RFSF FLO THERMOWELL 304 SS 1-1/2 600 # RF SS FLO THERMOWELL 304 SS 1-1/2 600 # RJ SS FLO THERMOWELL 304 SS 1-1/2 900 # RJ SS FLO THERMOWELL 304 SS 1-1/2 1500 # RJ SS FLO THERMOWELL 304 SS 1-1/2 2500 # RJ SS FLO


NONE

INSTRUMENT

1 OF 8

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXIV

SEQ.

NO.

REV

SIZE ITEM NAME




01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

TW-L1X TW-L1 TW-L2 TW-L3 TW-L3X TW-L3R TW-L4 TW-L4X TW-L5 TW-L5X TW-L6 TW-L6R TW-L9 TW-L15 TW-L25 TW-S1X TW-S1 TW-S2 TW-S3 TW-S3R TW-S3X TW-S4 TW-S4X TW-S5 TW-S5X TW-S6 TW-S6R TW-S9 TW-S15 TW-S25 TW-M1 TW-M2 TW-M3 TW-M4 TW-M4X TW-M5 TW-M5X

712 …… THERMOWELLS (CONTINUED) ……. THERMOWELL 304L SS 1-1/2 150 # RFSF FLG THERMOWELL 304L SS 1-1/2 150 # RF SS FLG THERMOWELL 304L SS 1-1/2 INCH NPT MPT THERMOWELL 304L SS 1-1/2 300 # RF SS FLG THERMOWELL 304L SS 1-1/2 300 # RFSF FLG THERMOWELL 304L SS 1-1/2 300 # RJ SS FLG THERMOWELL 304L SS 2 INCH 150# RF FLG THERMOWELL 304L SS 2 INCH 150# RFSF FLG THERMOWELL 304L SS 2 INCH 300# RF FLG THERMOWELL 304L SS 2 INCH 300# RFSF FLG THERMOWELL 304L SS 1-1/2 600 # RF SS FLG THERMOWELL 304L SS 1-1/2 600 # RJ SS FLG THERMOWELL 304L SS 1-1/2 900 # RJ SS FLG THERMOWELL 304L SS 1-1/2 1500 # RJ SS FLG THERMOWELL 304L SS 1-1/2 2500 # RJ SS FLG THERMOWELL 316 SS 1-1/2 150 # RFSF FLG THERMOWELL 316 SS 1-1/2 150 # RF SS FLG THERMOWELL 316 SS 1-1/2 INCH NPT MPT THERMOWELL 316 SS 1-1/2 300 # RF SS FLG THERMOWELL 316 SS 1-1/2 300 # RJ SS FLG THERMOWELL 316 SS 1-1/2 300 # RFSF FLG THERMOWELL 316 SS 2 INCH 150# RF FLG THERMOWELL 316 SS 2 INCH 150# RFSF FLG THERMOWELL 316 SS 2 INCH 300# RF FLG THERMOWELL 316 SS 2 INCH 300# RFSF FLG THERMOWELL 316 SS 1-1/2 600 # RF SS FLG THERMOWELL 316 SS 1-1/2 600 # RJ SS FLG THERMOWELL 316 SS 1-1/2 900 # RJ SS FLG THERMOWELL 316 SS 1-1/2 1500 # RJ SS FLG THERMOWELL 316 SS 1-1/2 2500 # RJ SS FLG THERMOWELL MONEL 1-1/2 150 # RF MONEL FLG THERMOWELL MONEL 1-1/2 INCHC NPT MPT THERMOWELL MONEL 1-1/2 300 # RF MONEL FLG THERMOWELL MONEL 2 INCH 150 # RF FLG THERMOWELL MONEL 2 INCH 150 # RFSF FLG THERMOWELL MONEL 2 INCH 300 # RF FLG THERMOWELL MONEL 2 INCH 300 # RFSF FLG


2 INCHES AND SMALLER-SCREWED: AND/OR COMPRESSION TYPE TUBE NONE

INSTRUMENT

2 OF 8

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXV

SEQ.

NO.

REV

SIZE ITEM NAME




01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

TW-F1X TW-F1 TW-F2 TW-F3 TW-F3R TW-F3X TW-F4 TW-F4X TW-F5 TW-F5X TW-F6 TW-F6R TW-F9 TW-F15 TW-F25 TW-G1X TW-G1 TW-G2 TW-G3 TW-G3R TW-G3X TW-G4 TW-G4X TW-G5 TW-G5X TW-G6 TW-G6R TW-G9 TW-G15 TW-G25 T/C-JS T/C-JD T/C-KS T/C-JD T/C-TS T/C-TD

712 …… THERMOWELLS (CONTINUED) ……. THERMOWELL 347 SS 1-1/2 150 # RFSF FLG THERMOWELL 347 SS 1-1/2 150 # RF SS FLG THERMOWELL 347 SS 1-1/2 INCH NPT MPT THERMOWELL 347 SS 1-1/2 300 # RF SS FLG THERMOWELL 347 SS 1-1/2 300 # RJ SS FLG THERMOWELL 347 SS 1-1/2 300 # RFSF FLG THERMOWELL 347 SS 2 INCH 150# RF FLG THERMOWELL 347 SS 2 INCH 150# RFSF FLG THERMOWELL 347 SS 2 INCH 300# RF FLG THERMOWELL 347 SS 2 INCH 300# RFSF FLG THERMOWELL 347 SS 1-1/2 600 # RF SS FLG THERMOWELL 347 SS 1-1/2 600 # RJ SS FLG THERMOWELL 347 SS 1-1/2 900 # RJ SS FLG THERMOWELL 347 SS 1-1/2 1500 # RJ SS FLG THERMOWELL 347 SS 1-1/2 2500 # RJ SS FLG THERMOWELL 446 SS 1-1/2 150 # RFSF FLG THERMOWELL 446 SS 1-1/2 150 # RF SS FLG THERMOWELL 446 SS 1-1/2 INCH NPT MPT THERMOWELL 446 SS 1-1/2 300 # RF SS FLG THERMOWELL 446 SS 1-1/2 300 # RJ SS FLG THERMOWELL 446 SS 1-1/2 300 # RFSF SS FLG THERMOWELL 446 SS 2 INCH 150# RF FLG THERMOWELL 446 SS 2 INCH 150# RFSF FLG THERMOWELL 446 SS 2 INCH 300# RF FLG THERMOWELL 446 SS 2 INCH 300# RFSF FLG THERMOWELL 446 SS 1-1/2 600 # RF SS FLG THERMOWELL 446 SS 1-1/2 600 # RJ SS FLG THERMOWELL 446 SS 1-1/2 900 # RJ SS FLG THERMOWELL 446 SS 1-1/2 1500 # RJ SS FLG THERMOWELL 446 SS 1-1/2 2500 # RJ SS FLG …… THERMOCOUPLES …… (THERMOCOUPLE ELEMENT LENGTH TO BE LISTED IN THE SIZE COLUMN OF THE MATERIAL TAKE-OFF DATA SHEET) THERMOCOUPLE SINGLE J-14 GAGE 1/2 IN NPT THERMOCOUPLE DUPLEX J-14 GAGE 1/2 IN NPT THERMOCOUPLE SINGLE K-8 GAGE 1/2 IN NPT THERMOCOUPLE DUPLEX K-8 GAGE 1/2 IN NPT THERMOCOUPLE SINGLE T-14 GAGE 1/2 IN NPT THERMOCOUPLE DUPLEX T-14 GAGE 1/2 IN NPT



INSTRUMENT

3 OF 8

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXVI

SEQ.

NO.

REV

SIZE ITEM NAME




01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

PI-DPH PI-DPH PI-DPH PI-DPH PI-DPH PI-DPH PI-DPH PI-DPH PI-DPH PI-DPH PI-316 PI-316 PI-316 PI-316 PI-316 PI-316 PI-316 PI-316 PI-316 PI-316 PI-316 PI-316 PI-316 PI-MON PI-MON PI-MON PI-MON PI-MON PI-MON PI-MON PI-MON PI-MON

712 …… PRESSURE GAUGES …… PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA W/DIAPH 4-1/2 316 SS TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 316 SS DRAWN TUBE & SOC PRESS GA 4-1/2 MONEL DRAWN TUBE & SOC PRESS GA 4-1/2 MONEL DRAWN TUBE & SOC PRESS GA 4-1/2 MONEL DRAWN TUBE & SOC PRESS GA 4-1/2 MONEL DRAWN TUBE & SOC PRESS GA 4-1/2 MONEL DRAWN TUBE & SOC PRESS GA 4-1/2 MONEL DRAWN TUBE & SOC PRESS GA 4-1/2 MONEL DRAWN TUBE & SOC PRESS GA 4-1/2 MONEL DRAWN TUBE & SOC PRESS GA 4-1/2 MONEL DRAWN TUBE & SOC



INSTRUMENT

4 OF 8

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXVII

SEQ.

NO.

REV

SIZE ITEM NAME




01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

PI-BRZ PI-REC PI-REC LG-1R LG-2R LG-3R LG-4R LG-5R LG-1R LG-2R LG-3R LG-4R LG-5R LG-1RHP LG-2RHP LG-3RHP LG1-RMS LG2-RMS LG3-RMS LG4-RMS LG5-RMS LG-1RM LG-2RM LG-3RM LG-4RM LG-5RM

712 …… PNEUMATIC OUTPUT AND

RECEIVER GAUGES ……

PRESS GA 2-1/2 BRONZE TUBE BRASS SOCKET REC GA 4-1/2 BRZ TUBE 0-10 SOUARE ROOT REC GA 4-1/2 BRONZE TUBE 0-100 UNIFORM …… LEVEL GAGES …… LEVEL GLASS 1 SECTION REFLEX LEVEL GLASS 2 SECTION REFLEX LEVEL GLASS 3 SECTION REFLEX LEVEL GLASS 4 SECTION REFLEX LEVEL GLASS 5 SECTION REFLEX LEVEL GLASS 1 SECT REFLEX W/OFFSET COCKS LEVEL GLASS 2 SECT REFLEX W/OFFSET COCKS LEVEL GLASS 3 SECT REFLEX W/OFFSET COCKS LEVEL GLASS 4 SECT REFLEX W/OFFSET COCKS LEVEL GLASS 5 SECT REFLEX W/OFFSET COCKS HP LEVEL GLASS 1 SECT REFLEX W/OFF COCKS HP LEVEL GLASS 2 SECT REFLEX W/OFF COCKS HP LEVEL GLASS 3 SECT REFLEX W/OFF COCKS LG R 1 SECT, HEAT CHMB, MONEL TRIM COCKS LG R 2 SECT, HEAT CHMB, MONEL TRIM COCKS LG R 3 SECT, HEAT CHMB, MONEL TRIM COCKS LG R 4 SECT, HEAT CHMB, MONEL TRIM COCKS LG R 5 SECT, HEAT CHMB, MONEL TRIM COCKS LG REFLEX 1 SECT MONEL TRIM COCKS LG REFLEX 2 SECT MONEL TRIM COCKS LG REFLEX 3 SECT MONEL TRIM COCKS LG REFLEX 4 SECT MONEL TRIM COCKS LG REFLEX 5 SECT MONEL TRIM COCKS



INSTRUMENT

5 OF 8

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXVIII

SEQ.

NO.

REV

SIZE ITEM NAME




01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

LG1-RSS LG2-RSS LG3-RSS LG4-RSS LG5-RSS LG1-RST LG2-RST LG3-RST LG4-RST LG5-RST LG-1T LG-2T LG-3T LG-4T LG-5T LG-1T LG-2T LG-3T LG-4T LG-5T LG-1TL LG-2TL LG-3TL LG-4TL LG-5TL LG-1TLS LG-2TLS LG-3TLS LG-4TLS LG-5TLS

712 …… LEVEL GAGES (CONTINUED) …… LEVEL GLASS 1 SECT REFLEX 316 SS & COCKS LEVEL GLASS 2 SECT REFLEX 316 SS & COCKS LEVEL GLASS 3 SECT REFLEX 316 SS & COCKS LEVEL GLASS 4 SECT REFLEX 316 SS & COCKS LEVEL GLASS 5 SECT REFLEX 316 SS & COCKS LG REFLEX 1 SECT W/ HTG CHAMBER & COCKS LG REFLEX 2 SECT W/ HTG CHAMBER & COCKS LG REFLEX 3 SECT W/ HTG CHAMBER & COCKS LG REFLEX 4 SECT W/ HTG CHAMBER & COCKS LG REFLEX 5 SECT W/ HTG CHAMBER & COCKS LEVEL GLASS 1 SECTION TRANS W/ ILLUM LEVEL GLASS 2 SECTION TRANS W/ ILLUM LEVEL GLASS 3 SECTION TRANS W/ ILLUM LEVEL GLASS 4 SECTION TRANS W/ ILLUM LEVEL GLASS 5 SECTION TRANS W/ ILLUM LEVEL GLASS 1 SECT TRANS W/ ILLUM & COCKS LEVEL GLASS 2 SECT TRANS W/ ILLUM & COCKS LEVEL GLASS 3 SECT TRANS W/ ILLUM & COCKS LEVEL GLASS 4 SECT TRANS W/ ILLUM & COCKS LEVEL GLASS 5 SECT TRANS W/ ILLUM & COCKS LEVEL GLASS 1 SECT TRAN W/ ILLUM-MS-COCKS LEVEL GLASS 2 SECT TRAN W/ ILLUM-MS-COCKS LEVEL GLASS 3 SECT TRAN W/ ILLUM-MS-COCKS LEVEL GLASS 4 SECT TRAN W/ ILLUM-MS-COCKS LEVEL GLASS 5 SECT TRAN W/ ILLUM-MS-COCKS LG T 1 SECT W/ILLUM MS HEAT CHMB & COCKS LG T 2 SECT W/ILLUM MS HEAT CHMB & COCKS LG T 3 SECT W/ILLUM MS HEAT CHMB & COCKS LG T 4 SECT W/ILLUM MS HEAT CHMB & COCKS LG T 5 SECT W/ILLUM MS HEAT CHMB & COCKS



INSTRUMENT

6 OF 8

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXIX

SEQ.

NO.

REV

SIZE ITEM NAME




01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

LG1-TKM LG2-TKM LG3-TKM LG4-TKM LG5-TKM LG1-THP LG2-THP LG3-THP LG1-TMS LG2-TMS LG3-TMS LG4-TMS LG5-TMS LG-1TM LG-2TM LG-3TM LG-4TM LG-5TM LG1-TST LG2-TST LG3-TST LG4-TST LG5-TST LG1-TSS LG2-TSS LG3-TSS LG4-TSS LG5-TSS

712 …… LEVEL GAGES (CONTINUED) …… LG T 1 SECT W/ ILLUM-KFS-MONEL TRIM COCKS LG T 2 SECT W/ ILLUM-KFS-MONEL TRIM COCKS LG T 3 SECT W/ ILLUM-KFS-MONEL TRIM COCKS LG T 4 SECT W/ ILLUM-KFS-MONEL TRIM COCKS LG T 5 SECT W/ ILLUM-KFS-MONEL TRIM COCKS HP LEVEL GLASS 1 SEC TRAN W/ ILUM & COCKS HP LEVEL GLASS 2 SEC TRAN W/ ILUM & COCKS HP LEVEL GLASS 3 SEC TRAN W/ ILUM & COCKS LG T 1 SECT. HEAT CHMD. MONEL TRIM COCKS LG T 2 SECT. HEAT CHMD. MONEL TRIM COCKS LG T 3 SECT. HEAT CHMD. MONEL TRIM COCKS LG T 4 SECT. HEAT CHMD. MONEL TRIM COCKS LG T 5 SECT. HEAT CHMD. MONEL TRIM COCKS LG TRAN 1 SECT W/ILUM & MONEL TRIM COCKS LG TRAN 2 SECT W/ILUM & MONEL TRIM COCKS LG TRAN 3 SECT W/ILUM & MONEL TRIM COCKS LG TRAN 4 SECT W/ILUM & MONEL TRIM COCKS LG TRAN 5 SECT W/ILUM & MONEL TRIM COCKS LG TRAN 1 SECT W/ HTG CHAMBER-ILLUM-COCK LG TRAN 2 SECT W/ HTG CHAMBER-ILLUM-COCK LG TRAN 3 SECT W/ HTG CHAMBER-ILLUM-COCK LG TRAN 4 SECT W/ HTG CHAMBER-ILLUM-COCK LG TRAN 5 SECT W/ HTG CHAMBER-ILLUM-COCK LG 1 SECT 316 SS TRANS W/ILLUM AND COCKS LG 2 SECT 316 SS TRANS W/ILLUM AND COCKS LG 3 SECT 316 SS TRANS W/ILLUM AND COCKS LG 4 SECT 316 SS TRANS W/ILLUM AND COCKS LG 5 SECT 316 SS TRANS W/ILLUM AND COCKS



INSTRUMENT

7 OF 8

JULY, 2005 NIOEC-SP-70-03(0)

APPENDIX I XXX

SEQ.

NO.

REV

SIZE ITEM NAME




01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

PCV-35 PCV-100 PCV-75H PCV-20 XY-999 XCV-5 XCV-6 XCV-4

712 …… FILTER-REGULATORS … FILTER/REGULATOR SPNING RANGE .35 T0 2.4 BARS FILTER/REGULATOR SPRING RANGE .3-6.0 BARS FILTER/REG SPRING RANGE .3-2.4 BARS W/HDWL REGULATOR-RANGE .2-1.3 BARS/MANUAL RESET …… I/P TRANSDUCER …… I/P TRANSDUCER W/REG & GAGE FISHER 5465 …… STEAM TPAPS …… LINE STM TRAP SS 3/4 IN. 1MP .3-41 BARS TRACING STM TRAP SS 1/2 IN. 1MP .3-41 BAR STM TRAP 3/4 1MP W/STRAINER MAX 45 BAR


NONE

INSTRUMENT

8 OF 8

Date post:	07-Apr-2018
Category:	Documents
Upload:	donga
View:	267 times
Download:	11 times

NATIONAL IRANIOEC SPEC. - صفحه...

Documents