National Conference on Weights and Measures15245 Shady Grove Road, Suite 130 • Rockville, MD 20850

Certificate Number: 95-143Page 1 of 2

National Type Evaluation ProgramCertificate of Conformance

for Weighing and Measuring Devices

This device was evaluated under the National Type Evaluation Program (NTEP) and was found to comply with the applicable technicalrequirements of Handbook 44, "Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices."Evaluation results and device characteristics necessary for inspection and use in commerce are on the following pages.Effective Date: October 10, 1995

Louis E. Straub G. Weston DiggsChairman, NCWM, Inc. Chairman, National Type Evaluation Program Committee

Issued Date: May 3, 1996Note: The National Conference on Weights and Measures does not "approve", " recommend", or "endorse" any proprietary product or material, either as asingle item or as a class or group. Results shall not be used in advertising or sales promotion to indicate explicit or implicit endorsement of the product ormaterial by the NCWM.

This is a reissuance by the NCWM of a Certificate of Conformance already issued by the National Institute of Standards and Technology.

Submitted by:Jonel Engineering500 East Walnut AvenueFullerton, CA 92632-0798Tel: (714) 879-2360Fax: (714) 526-2397Contact: Stephen Lawson

For:Batching ControllerPC Computer, Application SoftwareModel: Advantage Batching Controller(ABC)

Standard Features and Options

Ticket print capabilitiesMotion detection is determined by the primary weight indicatorVideo display (CRT), primary indications are provided by the CRT; the external slave indicator isfor informational purposes onlyMultiple weighing element interface with identificationSoftware support for external devices: Modem, scale controller and gatesVehicle, customer and product IDCategory 3 audit trail for sealing purposesIBM compatible hardwareLanguage: Basic, Assembler

Certificate No.: 95-143Page 2 of 2

Jonel EngineeringBatching Controller

Model: Advantage Batching Controller (ABC)

System Description: This system consists of compatible, certified indicating and load receivingelements, water meters, monitor, keyboard, process logic controller (PLC), and one or moreslave printers.

Application: General purpose batching scale controller for asphaltic or cement concrete.

Identification: The required identification information is displayed on the main menu screenfor the system ID. From the main menu, select "config" and then "values" to view theaggregate and cement indicating element identification information. The plus and minus keysare used to view the aggregate and cement ID screens.

Sealing: The video display (primary indicator) uses a Category 3 audit trail and is viewable in the“Scale Audit Report” on the CRT. The external slave indicating element does not affect theamplified load cell signal to the CRT and is for informational purposes only.

Test Conditions: A field evaluation was conducted on this system interfaced with a JonelModel JL-DSD-253B indicating element (Certificate of Conformance 90-072) as the source ofthe weight and motion detection information. The emphasis of the evaluation was on theperformance of the computer system, its interaction with the load receiving element, andinformation printed on the weight ticket. The results of the evaluation indicate the devicecomplies with applicable requirements.

Type Evaluation Criteria Used: NIST Handbook 44, 1995 Edition

Tested By: Ronald Flores (CA)

National Conference on Weights and Measures15245 Shady Grove Road, Suite 130 • Rockville, MD 20850

Certificate Number: 96-038Page 1 of 2

National Type Evaluation ProgramCertificate of Conformance

for Weighing and Measuring Devices

This device was evaluated under the National Type Evaluation Program (NTEP) and was found to comply with the applicable technical requirements ofHandbook 44, "Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices." Evaluation results and devicecharacteristics necessary for inspection and use in commerce are on the following pages.

This device was evaluated under the National Type Evaluation Program (NTEP) and was found to comply with the applicable technical requirements ofHandbook 44, “Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices.” Evaluation results and devicecharacteristics necessary for inspection and use in commerce are on the following pages.

Effective Date: March 18, 1996

Louis E. Straub G. Weston DiggsChairman, NCWM, Inc. Chairman, National Type Evaluation Program Committee

Issue date: May 22, 1996Note: The National Conference on Weights and Measures does not "approve”, “recommend", or "endorse" any proprietary product or material, either as asingle item or as a class or group. Results shall not be used in advertising or sales promotion to indicate explicit or implicit endorsement of the product ormaterial by the NCWM.

This is a reissuance by the NCWM of a Certificate of Conformance already issued by the National Institute of Standards and Technology.

Submitted by:Concrete Equipment Co., Inc.237 North 13th StreetPO Box 430Blair, NE 68008Tel: (402) 426-4181Fax: (402) 426-4190Contact: Don Hansen

For:Hopper Scale Weighing/Load Receiving ElementLoad Cell ElectronicModel: HS Series *nmax: 2000Capacity: 8000 to 50 000 lb

Accuracy Class: III L

Standard Features and Options

*The specific Model Designations are: HS-X-O-YY, where

HS = Hopper ScaleX = Material weighed (C = cement, A = aggregate, W = water)O = (No metrological significance)YY = Maximum batch size (10 = 10 yard, 05 = 5 yard, etc.)

Specific models may be suspended from three (3) or four (4) “S” type load cells

Load cells used: Rice Lake Model RL20000A-XXX (Certificate of Conformance No. 90-158)

Temperature Range: -10 to 40 °C (14 to 104 °F)

Certificate Number: 96-038Page 2 of 2

Concrete Equipment Co., Inc.Hopper Scale Weighing/Load Receiving Element

Model: HS Series

Application: Hopper Scale weighing elements for use with certified indicators in portable and permanent ready mixedconcrete batching plants.

Identification: A metal identification plate is permanently attached to the side of the hopper.

Sealing: All calibration parameters are sealed in the indicator. The load cell junction box has no adjustable components,however, it can also be sealed with a pressure sensitive security seal on one edge of the hinged cover.

Test Conditions: Three models were tested to cover the family; 8000 x 4 lb (three cells), 10 000 x 4 lb (four cells), and 40000 x 20 lb (four cells). The weighing elements were interfaced with Cardinal Model 738 indicators (CC No. 86-035A3). The emphasis of the evaluation was on the design and performance of the weigh hoppers. All three modelswere tested using at least 25% of capacity of known test standards and direct substitution methods to capacity of thedevices. Several increasing/decreasing load, discrimination and return to zero tests were conducted. The indicator andjunction box of each scale was sealed and similar tests were repeated after the scales were used for the time andnumber of weighments criteria had been met. All test results were within acceptance tolerances.

Results of the evaluation indicate the devices comply with applicable requirements.

Type Evaluation Criteria Used: NIST Handbook 44, 1996 Edition

Tested By: Richard Suiter (NE) and Lonnie Fierstein (NE)

National Conference on Weights and Measures 15245 Shady Grove Road, Suite 130 • Rockville, MD 20850

Certificate Number: 07-114

Page 1 of 2 National Type Evaluation Program

Certificate of Conformance for Weighing and Measuring Devices

This device was evaluated under the National Type Evaluation Program (NTEP) and was found to comply with the applicable technical requirements of Handbook 44, "Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices." Evaluation results and device characteristics necessary for inspection and use in commerce are on the following pages.

Judith L. Cardin Don Onwiler Chair, NCWM, Inc. Chairman, National Type Evaluation Program Committee

Issue date: November 28, 2007 Note: The National Conference on Weights and Measures does not "approve", "recommend", or "endorse" any proprietary product or material, either as a single item or as a class or group. Results shall not be used in advertising or sales promotion to indicate explicit or implicit endorsement of the product or material by the NCWM.

Submitted by: BMH Systems 71 ch. Du. Tremblay Boucherville Quebec, Canada, J4B7L6 Tele: (450) 449-4770 Fax: (450) 449-4898 Contact: Louis-P Isabelle

For: Weighing/load-receiving Element Cement Aggregate Hopper; Load Cell Electronic Models: BA-12, BC-12 Capacity: ** See Below nmax: See Below emin: See Below Accuracy Class: III L

Standard Features and Options This Certificate covers concrete batch weighing hoppers for aggregate and cement. ** The standard models of weighing elements covered by this certificate are listed below. Capacities: Model BA-12: 40 000 lb x 40 lb (aggregate) nmax: 1000 emin: 40 lb Tension with 4 supports Model BC-12: 10 000 lb x 10 lb (cement) nmax: 1000 emin: 10 lb Compression with 3 supports Construction: Mild Steel Load Cells used:

Four (4) Sensortronics Model 60001A15K (NTEP CC 86-043) S-beam tension (BA-12) Three (3) Rice Lake Model RL70000 5 K (NTEP CC 97-125) double-ended shear beam compression

Mounted with rods and, TWA assembly, EZ-mount by Rice Lake (BC-12) Temperature range: -10 C to 40 C (14 F to 105 F)

Certificate Number: 07-114 Page 2 of 2

BMH Systems

Weighing/Load-receiving Element Model: BA-12, BC-12

Application: General purpose weighing/load-receiving element when connected to a certified and compatible indicating element. Identification: The engraved identification badge is riveted to the side of the Frame. Sealing: The load cell junction box can be sealed with a wire security seal threaded through two screws on the cover. Test Conditions: Hoppers tested BA -12 aggregate and BC-12 cement. The emphasis of the evaluation was on design, operation and performance of the device. Hoppers submitted for evaluation were interfaced with an Acer computer model M-JL-DSD-253B (NTEP CC 95-143). Several increasing/decreasing tests were performed to capacity of each hopper submitted, using 25% of certified test weights. The devices were sealed and permanence tests consisting of 300 weighing operations over approximately 30 days were conducted. The devices were reevaluated using similar test methods. Evaluated By: T. L. Davis (KS) Type Evaluation Criteria Used: NCWM Publication 14, 2007 Edition; NIST Handbook 44, 2007 Edition Conclusion: The results of the evaluations and information provided by the manufacturer indicate the devices comply with applicable requirements. Information Reviewed By: S. Patoray, L. Bernetich (NCWM) Example of BC-12 Example of BC-12 load cell

Example of BA-12 Example of BA-12 load cell

Certificate Number: 10-072A1 Page 1 of 2 

1135 M Street, Suite 110 / Lincoln, Nebraska 68508 The National Conference on Weights and Measures (NCWM) does not approve, recommend or endorse any proprietary product or material, either as a single item or as a class or group. Results shall not be used in advertising or sales promotion to indicate explicit or implicit endorsement of the product or material by the NCWM. 

For Hopper Scale Weighing/Load-receiving Element, Load Cell Electronic Rectangular Design Model: KSi-xxx and KSi-xxx-EXT Series nmax: 4 680 emin: 5 lb Capacity: 2 250 to 23 400 lb Hopper Size: (see below) Accuracy Class: III

Submitted By: KSi Conveyors, Inc. 235 U Road Sabetha, KS 66534 Tel: 785-284-0600 x 125 Fax: 785-284-0603 Contact: Paul Kaeb Email: paulkaeb@ksiconveyors.com Web site: www.ksiconveyors.com

Standard Features and Options Specific model designations are KSi-xxx and KSi-xxx-EXT, where the xxx is capacity in bushel and the EXT designates extension legs Models tested: KSi-225, 11 250 x 5 lb, 96 in L x 96 in W x 80 in high; KSi-375, 18 750 x 5 lb, 96 in L x 96 in W x 110 in high, and Model KSi-375-EXT, 18 750 x 5 lb ,96 in L x 96 in W x 110 in H Rectangular hopper, steel construction 4 leg design using 4 load cells Approved Parameters: Capacity: 2 250 to 23 400 lb Hopper Height: 40 in to 137 in Hopper Length: 48 in to 105 in Hopper Width: 48 in to 105 in Extension Legs up to 10 ft Load Cell Used: 4 – Cardinal Model SB-5000S (NTEP CC No. 87-059A1), or NTEP certified metrologically equivalent load cells. Installations must satisfy the relationship of vmin d/N, where N= number of load cells.

Temperature Range: -10 ºC to 40 ºC (14 ºF to 104 ºF) This device was evaluated under the National Type Evaluation Program and was found to comply with the applicable technical requirements of "NIST Handbook 44: Specifications, Tolerances and Other Technical Requirements for Weighing and Measuring Devices." Evaluation results and device characteristics necessary for inspection and use in commerce are on the following pages.

Stephen Benjamin Kurt FlorenChairman, NCWM, Inc. Chairman, National Type Evaluation Program Committee

Issued: December 20, 2012

Certificate Number: 10-072A1 Page 2 of 2

KSi Conveyors, Inc.

Hopper Scale / KSi-xxx and KSi-xxx-EXT Series

Application: Designed as a Class III hopper scale for weighing grain and other products.

Identification: A stamped metal ID plate is attached to one of the hopper legs.

Sealing: The load cell junction box is sealed with a wire security seal inserted through two of the drilled-head screws that secure the junction box cover.

Test Conditions: The purpose of the evaluation was to include the leg extension model. The emphasis of the evaluation was on the design and performance of the hopper load-receiving element. Model KSi-xxx-EXT, 18 750 x 5 lb (96 in L x 96 in W x 110 in H) hopper scale attached to Cardinal Scale Model 205 indicating element (NTEP CC 01-011A5) and four Cardinal Model SB-5000S load cells (NTEP CC 87-059A1) was tested. Several increasing, decreasing load tests were performed to capacity using a substitution test methods plus 5 000 lb of certified test weight respectively. Several center of zero tests and discrimination tests near zero and near capacity were also performed. The device was sealed for the required time and use and then retested in a similar manner to demonstrate permanence of performance. Previous test conditions are shown below for reference.

Certificate of Conformance Number 10-072: The emphasis of the evaluation was on the design and performance of the hopper load-receiving element. Model KSi-225, 11 250 x 5 lb (96 in L x 96 in W x 80 in H) and a Model KSi-375, 18 750 x 5 lb (96 in L x 96 in W x 110 in H) hopper scales attached to Cardinal Scale Model 205 indicating element (NTEP CC 01-011A5) and four Cardinal Model SB-5000S load cells (NTEP CC 87-059A1). Several increasing, decreasing load tests were performed to capacity using a substitution test methods plus 4 000 and 4 700 lb of certified test weight respectively. Several center of zero tests and discrimination tests near zero and near capacity were also performed. The devices were sealed for the required time and use and then retested in a similar manner to demonstrate permanence of performance.

Evaluated By: T. Davis (KS) 10-072; E.A.Payne, Jr (MD) 10-072A1

Type Evaluation Criteria Used: NIST, Handbook 44: Specifications, Tolerances and Other Technical Requirements for Weighing and Measuring Devices, 2012. NCWM, Publication 14: Weighing Devices, 2012.

Conclusion: The results of the evaluation and information provided by the manufacturer indicate the device complies with applicable requirements.

Information Reviewed By: J. Truex (NCWM) 10-072, 10-072A1

Examples of Device:

Certificate Number: 12-124 Page 1 of 2

1135 M Street, Suite 110 / Lincoln, Nebraska 68508 The National Conference on Weights and Measures (NCWM) does not approve, recommend or endorse any proprietary product or material, either as a single item or as a class or group. Results shall not be used in advertising or sales promotion to indicate explicit or implicit endorsement of the product or material by the NCWM.

For: Hopper Scale Weighing/Load Receiving Element Model: KSI-VR-XXX Series nmax: 5 000 emin: 2 lb Capacity: 10 000 lb Platform: See Below Accuracy Class: III

Submitted By: KSi Conveyors Inc. 2345 U Road Sabetha, KS 66534 Tel: 785-284-0600 Fax: 785-284-0603 Contact: Paul Kaeb Email: paulkaeb@ksiconveyors.com Web site: www.ksiconveyors.com

Standard Features and Options

Specific model designations are KSI-VR-XXX where XXX is capacity in bushels

Model tested: KSI-VR-200, 10 000 x 2 lb, 100 in L x 100 in W x 80 in H

Rectangular hopper, steel construction 4-leg design using 4 load cells

Approved Parameters: Capacity: 2 000 lb to 12 500 lb Hopper Height from 40 to 100 inches Hopper Width from 50 to 110 inches Hopper Length from 50 to 110 inches

Options: Extension Legs up to 10 ft

Load Cells Used: 4- Cardinal Model SB5000S (NTEP CC No. 87-059A1), or NTEP certified metrologically equivalent load cells.

Installations must satisfy the relationship of vmin ≤d/√N, where N=number of load cells.

Temperature Range: -10 C to 40 C (14 F to 104 F) This device was evaluated under the National Type Evaluation Program and was found to comply with the applicable technical requirements of “NIST Handbook 44: Specifications, Tolerances and Other Technical Requirements for Weighing and Measuring Devices.” Evaluation results and device characteristics necessary for inspection and use in commerce are on the following pages.

Stephen Benjamin Kurt FlorenChairman, NCWM, Inc. Committee Chair, National Type Evaluation Program Committee

Issued: December 20, 2012

Certificate Number: 12-124 Page 2 of 2

KSi Conveyors, Inc Hopper Scale/ KSI-VR-XXX Series

Application: Designed as a Class III hopper scale for weighing grain and other products.

Identification: A stamped metal ID plate is riveted to one of the hopper legs.

Sealing: The load cell junction box is sealed with a wire security seal inserted through two of the drilled-head screws that secure the junction box cover.

Test Conditions: The emphasis of the evaluation was on the design and performance of the hopper load-receiving element. Model KSI-VR-200, 10 000 lb x 2 lb (100 in L x 100 in W x 80 in H) hopper scale attached to Cardinal Scale Model 210 indicating element (NTEP CC 01-011A7) and four Cardinal Model SB5000S load cells (NTEP CC 87-059A1). Several increasing and decreasing load tests were performed to capacity using substitution test methods plus 4000 lb of certified test weight. Several center of zero tests and discrimination tests near zero and near capacity were also performed. The device was sealed for the required time and use then retested in a similar manner to demonstrate permanence of performance.

SeeEvaluated By: E.A.Payne, Jr

Type Evaluation Criteria Used: NIST Handbook 44 Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices, 2012 Edition. NCWM Publication 14 Weighing Devices, 2012 Edition.

Conclusion: The results of the evaluation and information provided by the manufacturer indicate the device complies with applicable requirements.

Information Reviewed By: J. Truex (NCWM)

Example(s) of Device:

Certificate Number: 13-092A1 Page 1 of 2

1135 M Street, Suite 110 / Lincoln, Nebraska 68508 The National Conference on Weights and Measures (NCWM) does not approve, recommend or endorse any proprietary product or material, either as a single item or as a class or group. Results shall not be used in advertising or sales promotion to indicate explicit or implicit endorsement of the product or material by the NCWM.

For: Hopper Scale Weighing/Load Receiving Element, Electronic, Rectangular Model: KSi-MFxxx nmax: 3000 emin: 2 lb Capacity: 2000 lb to 7500 lb Hopper Size: See Below Accuracy Class: III

Submitted By: KSi Conveyors Inc 2345 U Road Sabetha, KS 66534 Tel: 785-284-0600 Fax: 785-284-0603 Contact: Paul Kaeb Email: paulkaeb@ksiconveyors.com Web site: www.ksiconveyors.com

Standard Features and Options

Specific model designations are KSI-MF-xxx where xxx is capacity in bushels

Model Tested: KSi-MF120 6000 x 2 lb, 87.7 in H” x 52.1 in W x 99.5 in L

Rectangular hopper, mild steel construction 4-leg design using 4 load cells

Approved Parameters:

Capacity: 2000 lb to 7500 lb Hopper Height: 43.88 in to 109.7 in Hopper Width: 26.05 in to 57.3 in Hopper Length: 49.75 in to 109.45 in

Options:

Extension legs up to 12 ft

Load Cells Used: 4- Cardinal Model SB2500S (NTEP CC No. 87-059A1), or NTEP certified metrologically equivalent load cells.

Installations must satisfy the relationship of vmin ≤ d ÷ √N, where N=number of load cells. Temperature Range: -10 C to 40 C (14 F to 104 F) This device was evaluated under the National Type Evaluation Program and was found to comply with the applicable technical requirements of “NIST Handbook 44: Specifications, Tolerances and Other Technical Requirements for Weighing and Measuring Devices.” Evaluation results and device characteristics necessary for inspection and use in commerce are on the following pages.

John Gaccione Stephen BenjaminChairman, NCWM, Inc. Committee Chair, National Type Evaluation Program Committee

Issued: October 18, 2013

Certificate Number: 13-092A1 Page 2 of 2

KSi Conveyors Inc Hopper Scale/ KSi-MFxxx

Application: Designed as a Class III hopper scale for weighing grain (minimum 2000 scale divisions required by Handbook 44) and other products (minimum 1000 scale divisions required by NIST Handbook 44).

Identification: A stamped metal ID plate is riveted to one of the hopper legs. Sealing: The load cell junction box is sealed with a wire security seal inserted through two of the drilled-head screws that secure the junction box cover. Seal the indicating element as stated in its own certificate of conformance.

Test Conditions: This certificate supersedes NTEP Certificate of Conformance Number 13-092 and was issued to increase the minimum capacity from 1200 lb to 2000 lb and to clarify the minimum number of divisions required by NIST Handbook 44. No additional testing was necessary. Previous test conditions are listed below for reference.

Certificate of Conformance Number 13-092: The emphasis of the evaluation was on the design and performance of the hopper load-receiving element. A model KSi-MFxxx 6000 lb x 2 lb (87.75” x 52.1” x 99.5”) hopper scale attached to a Cardinal model 205 indicating element (NTEP CC 01-011 ) and four (4) Cardinal SB2500S load cells (NTEP CC 87-059A1). Several increasing and decreasing load tests were performed to capacity using substitution test methods plus 2000 lb of certified test weight. Several center of zero tests and discrimination tests near zero and near capacity were also performed. The device was sealed at both the indicating element and the junction box and over 300 weighments were performed over 42 days (meeting the minimum requirements of Publication 14).All weighments were at least 20% of capacity and half the weighments were over 50% of capacity of the device. The device was then retested in a similar manner to demonstrate permanence of performance.

Evaluated By: E.A.Payne, Jr (MD), Z. Tripoulas (MD) 13-092

Type Evaluation Criteria Used: NIST Handbook 44 Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices, 2013 Edition. NCWM Publication 14 Weighing Devices, 2013 Edition.

Conclusion: The results of the evaluation and information provided by the manufacturer indicate the device complies with applicable requirements.

Information Reviewed By: J. Truex (NCWM) 13-092, 13-092A1

Example of Device:

KSi-MF120 (Multi-Flow)

Certificate Number: 14-009 Page 1 of 2

1135 M Street, Suite 110 / Lincoln, Nebraska 68508 The National Conference on Weights and Measures (NCWM) does not approve, recommend or endorse any proprietary product or material, either as a single item or as a class or group. Results shall not be used in advertising or sales promotion to indicate explicit or implicit endorsement of the product or material by the NCWM.

For: Automatic Bulk Weighing System Automatic Bulk, Scale Controller, Software Model: KSi-ABWS-AT & KSi-AT Version: KSi-ABWS-AT 4.0 or Higher Version: KSi-AT 3.2 * Accuracy Class: III, III/IIIL

Submitted By: KSi Conveyors Inc. 2345 U Road Sabetha, KS 66534 Tel: 785-284-0600 Fax: 785-284-0603 Contact: Paul Kaeb Email: paulkaeb@ksiconveyors.com Web site: www.ksiconveyors.com

Standard Features and Options The capacity and division size and nmax depend on the parameters of the scale system. Motion detection is provided by the approved and compatible indicating element.

Load-Out Capabilities Ticket Printing Capabilities Touch Screen Semi-Automatic Zero (Push-Button) Ethernet/LAN RS232/USB Time and Date

* Scale Controller Only and not ABWS Minimum System Requirements: KSi-ABWS-AT:

Windows 7 Intel Core CPU 1.70 GHz RAM 4.00 GB

KSi-AT: The operator interface for KSi AutoTreat V3.2 was developed using the C-More programming software suite from

AutomationDirect and requires the associated C-More screen hardware from AutomationDirect.

This device was evaluated under the National Type Evaluation Program and was found to comply with the applicable technical requirements of “NIST Handbook 44: Specifications, Tolerances and Other Technical Requirements for Weighing and Measuring Devices.” Evaluation results and device characteristics necessary for inspection and use in commerce are on the following pages.

John Gaccione Stephen Benjamin

Chairman, NCWM, Inc. Committee Chair, National Type Evaluation Program CommitteeIssued: January 31, 2014

Certificate Number: 14-009 Page 2 of 2

KSI Conveyors, Inc Automatic Bulk Weighing System Controller / KSi-ABWS-AT & KSi-AT

Application: The model KSi-ABWS-AT system controller may be used in any bulk weighing scale system. When used as part of a system to weigh grain, it must be marked as a Class III device and have a minimum of 2000 scale divisions. When used in a bulk weighing system for any commodity other than grain, it must be marked as Class III or Class IIIL, whichever is appropriate. The model KSi-AT is designed as a scale controller only and when used in a system to weigh grain, it must have a Class III device and have a minimum of 2000 scale divisions.

Identification: For the KSi-ABWS-AT the G.S.1 information can be obtained by clicking the “G.S.1 Icon”. The KSi-AT has the NTEP certificate number displayed on the lower banner bar and then to obtain the current version number, select the “Support Menu”.

Sealing: There are no metrological functions that require a seal. Seal the indicating element in accordance with its own sealing requirements.

Operation: The KSi-ABWS-AT operates in both the automatic and manual modes. The KSi-AT is used as a general scale controller.

Test Conditions: The emphasis of the evaluation was on device design, operation, performance and compliance with marking requirements. The model KSi-ABWS-AT software loaded on a PC and was interfaced with a Cardinal model 210 (NTEP CC# 13-028) and a load cell simulator in order to simulate automatic bulk weighing cycles. Numerous drafts were performed to verify printing of each draft and d no-load conditions. The evaluation consisted of a review for compliance with the Checklist for Automatic Bulk Weighing Systems; Publication 14.

The model KSi-AT scale controller software was loaded on a PC and interfaced with a Cardinal model 210 (NTEP CC# 13-028) and a load cell simulator. Numerous weight transactions and printing operations were performed.

Evaluated By: E.A.Payne, Jr (MD)

Type Evaluation Criteria Used: NIST Handbook 44 Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices, 2014 Edition. NCWM Publication 14 Weighing Devices, 2013 Edition.

Conclusion: The results of the evaluation and information provided by the manufacturer indicate the device complies with applicable requirements.

Information Reviewed By: J. Truex (NCWM)

Examples of Device:

KSi-AT Screen KSi-ABWS-AT Screen