~X~L~’ ~L~\~NDALGALlON MANUFACTURING COMPANY, Gallon, OhIo 44833, U.S.A.a Jeffrey Gallon inc. Company
CONVERTER OUTPUT SHAFT GOVERNOR
The instructions in this section basically apply to all governorsused on Galion Grade-O-Matic graders and Roll—O-Matic rollers
Adjustment of governor to engine fuel systemthe unit operator’s manual.
procedure is found in
Lubricating instructions for governors not having pressure lubesupply are found in the unit operator’s manual.
CONTENTS
Disassembly 1—7
Assembly 7 - 13
ROLfE~[
3/74~
PAGE
‘U
fF
• FILE: t.SECTION: .i_
1 Disassembly
Remove adjusting screw eye lock nut (1),adjusting screw eye (2), and governor spring (3).
2
Remove speed change shaft snapring and washer.
3
Remove speed change lever and shaft andspeed change spring lever as an assembly.
N’
1
1338
1339
1340
MANUAL aaC
3
2
FILE: ~SECTION: .L. SHOP I, MANUAL
4
Remove speed change bracket.
CE
5
Remove throttle lever roll pin.
Remove throttle lever from rocker shaft.
6
Remove spring lever roll pin.
1341
134Z
Remove lever from rocker shaft.
2
-c~
I ,7....W.*%
1
Remove four body-to-base attaching screws.
Remove body and gasket (1) from base.
8
I
o
~ a.ç
J4I1344
Remove capscrews from rocker yoke (1).
Remove yoke from body.
9 1.345
Remove oil seal.
B~y seal consists of two parts--a metalbackup washer and a neoprene seal.
•:j :l~
1346
FILE: 1-...SECTION: L SHOP
7
e MANUAL
1
I
3
Remove bumper screw from body.
4
1349 C7--
SECTION: ± SHOP MANUALC
1347
10
Remove snapring from rocker shaft.
11
Move shaft through bearing and body.
Bearing, seal, and snapring at oppositeend of shaft will remain on shaft.
12
Oo~
1348
~iI A XTYT A IItlAfl U IlL Ia
13
Examine body bushing for wear.
Do not remov& bushing unless replacementis needed.
14
Remove thrust sleeve and bearing from spiderand shaft assembly.
15
Remove thrust bearing from thrust sleeve.
135(
1351
1352
FILE: t...SECTION: ± SHOP
I
5
:J. FILE:_L.SECTION: t
16
SHOP MANUAL —a
Remove weight pin clips (1) from weightpins (2).
NOTE: Weight pins are knurled at one end onlyand clips should be removed from end oppositethe knurling.
17
Remove pins and weights from spider andshaft assembly.
18
U;;a ill
1353
1354
C:
Remove drive shaft snapring.
Use Waldes-Truarc pliers #2 or equal.
135C
a
6
FILE: _i.SECTION: L SHOP e MANUAL
19
Remove spider and shaft assembly from baseand bearing.
20
Remove base bearing snap ring (1).
Press bearing (2) from base.
21
Press base bearing (2) into base.
Install snapring (1).
it ~1/5
2
2
1356
1357
1357
1
1
7
FILE: ..i_.SECTION: £ SHOP MANUAL
Install spiderand base.
22
and shaft assembly bearing
231356
Install drive shaft snap ring.
Use Waldes-Truarc pliers #2 or equal manufactured by Waldes Kohinoor, Inc., LongIsland City, New York.
241355
Install weights, pins, and pinspider and shaft assembly.
NOTE: Install pins from rightwith knurled endat right (2).
clips on
to left
Installed in this manner, centrifugalforce can not throw pins from spider andfree weights.
8
7
SECTION:
Install thrust bearing on thrust sleeve.
26
Install thrust sleeve and bearing on spiderand shaft assembly.
If needed, installof body.
new body bushing in top
1350
B
6 SHOP ~IL~
25
MANUAL ‘a’
1352
27 1351
9
FILE: BSECTION: ..j SHOP MANUAL
A~
28
Install bumper screw in body.
29
Install bearing, snapring, and seal on oneend of rocker shaft,
Install shaft in body and at other end, install bearing, snapring, and seal.
30
Install rocker yoke in body..
Attach to rocker shaft with two capscrews.
C
1349
-s
I
1348
(.10
FILE: ..L_SECTION: ± SHOP MANUAL
Sn
31
Install gasket (1) on base.
Attach body to base with four screws andlockwashers.
32
Install spring lever on rocker shaft.
I
Secure in place with roll pin.
33
1a.
—
I
N
Install throttle lever on rocker shaft.
Secure in place with roll pin.
11
Sr4.-’’;
1342
-j
1
I‘La
* SECTION __ SHOP34
Install speed change bracket
35
itkA XTU ~IYIAIN AL
C-
1341
/
Install speed change spring lever and speedchange shaft
36
Ins tall speed change s≤aftring.
washer and snap-
12
I
1~ I4
38
Ins tall governor on output shaft.
Hook uprods (2)
lubricating line (1) and control
39
If stop screws (1) are in governor, removeand discard.
For correct adjustment, follow procedureoutlined in operator’s manual.
1338
FILE: ~SECTION: ~ SHOP
37
Install governor spring and screw eye andlock nut.
MANUAL
C
3
2
1
13
--
C:
F~.. (