+ All Categories
Home > Technology > Netzer ds 37-16-specsheet

Netzer ds 37-16-specsheet

Date post: 20-Aug-2015
Category:
Upload: electromate
View: 57 times
Download: 3 times
Share this document with a friend
Popular Tags:
8
DS-37-16 Absolute posiƟon, rotary Electric Encoder™ Mechanical - common to all types Allowable mounƟng eccentricity (2) ±0.2 mm Allowable rotor axial moƟon (2) ±0.2 mm Rotor inerƟa 71.62 gr · mm 2 Total weight 10 gr Outer diameter / Inner diameter / Prole 37 /10 / 8 mm Material (stator, rotor) Ultem™ polymer DS-37-16 Data Sheet , V 1.0c , July 2010 Electrical - common to all types Supply voltage 5V ± 5% (3) InterconnecƟon 250 mm Teon-coated, loose AWG-32 wires Environment - common to all types EMC (4) IEC 6100-6-2, IEC 6100-6-4 OperaƟng temperature range -55°C to +125°C (5) RelaƟve humidity <98 % - non condensing Shock endurance IEC 60068-2-27 ; 100 g for 11 ms VibraƟon endurance IEC 60068-2-6 ;20 g 10 – 2000 Hz ProtecƟon (6) IP 40 The holisƟc (1) structure of the Electric Encoder™ provides generous mounƟng tolerance, thus obviaƟng the need for internal ball bearings. The lack of bearings and components such as exible couplers, glass disc, light sources and detectors, along with very low power consumpƟon makes the DS-37 encoder virtually failure free. The internally shielded, DC operated Electric Encoder™ includes an electric eld generator, a eld receiver, a sinusoidal shaped dielectric rotor, and processing electronics. The outputs signals of Electric Encoder™ are analog Sine / Cosine represenƟng the rotaƟon angle. The digital outputs are obtained by further processing which may be either internal or external to the encoder. Outputs opƟons Analog Digital Sine/Cosine SSi AqB + Index Performance - common to all types Electrical Cycles/RevoluƟon – Fine/Coarse channels (7) 16 / 3 Angular resoluƟon (using 12 bit A/D conversion) (8) 17 bits StaƟc error (with oset compensaƟon) (9) < 25 mDeg Maximum operaƟonal speed (10) 3,500 rpm Measurement range Unlimited rotaƟon The DS-37 is a member of the DS series of Electric Encoders, based on Netzer Precision proprietary technology. These encoders oer many advantages, some unparalleled: Low prole (8 mm). Hollow, oaƟng shaŌ. No bearings or other contacƟng elements. High precision. High tolerance to temperature, shock, moisture, EMI, RFI and magneƟc elds. Analog or mulƟple digital interface opƟons. Extremely low power opƟons. The DS-37 is suited to demanding applicaƟon such as: aerospace, medical, instrumentaƟon, automaƟon, etc. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com [email protected] Sold & Serviced By:
Transcript
Page 1: Netzer ds 37-16-specsheet

DS-37-16 Absolute posi on, rotary Electric Encoder™

Mechanical - common to all types Allowable moun ng eccentricity (2) ±0.2 mmAllowable rotor axial mo on (2) ±0.2 mmRotor iner a 71.62 gr · mm2

Total weight 10 grOuter diameter / Inner diameter / Profi le 37 /10 / 8 mmMaterial (stator, rotor) Ultem™ polymer

DS-37-16 Data Sheet , V 1.0c , July 2010

Electrical - common to all types Supply voltage 5V ± 5%

(3)

Interconnec on 250 mm Tefl on-coated, loose AWG-32 wires

Environment - common to all types EMC

(4) IEC 6100-6-2, IEC 6100-6-4

Opera ng temperature range -55°C to +125°C

(5)

Rela ve humidity <98 % - non condensing Shock endurance IEC 60068-2-27 ; 100 g for 11 ms

Vibra on endurance IEC 60068-2-6 ;20 g 10 – 2000 Hz

Protec on (6)

IP 40

The holis c (1)

structure of the Electric Encoder™

provides generous moun ng tolerance, thus obvia ng the need for internal ball bearings.

The lack of bearings and components such as fl exible couplers, glass disc, light sources and detectors, along with very low power consump on makes the DS-37 encoder virtually failure free.

The internally shielded, DC operated Electric Encoder™ includes an electric fi eld generator, a fi eld receiver, a sinusoidal shaped dielectric rotor, and processing electronics.

The outputs signals of Electric Encoder™ are analog Sine / Cosine represen ng the rota on angle. The digital outputs are obtained by further processing which may be either internal or external to the encoder.

Outputs op ons

Analog Digital Sine/Cosine SSi AqB + Index

Performance - common to all types Electrical Cycles/Revolu on – Fine/Coarse channels

(7) 16 / 3

Angular resolu on (using 12 bit A/D conversion) (8)

17 bitsSta c error (with off set compensa on)

(9)< 25 mDeg

Maximum opera onal speed (10)

3,500 rpmMeasurement range Unlimited rota on

The DS-37 is a member of the DS series of Electric Encoders, based on Netzer Precision proprietary technology. These encoders off er many advantages, some unparalleled: • Low profi le (8 mm).• Hollow, fl oa ng sha . • No bearings or other contac ng elements.• High precision. • High tolerance to temperature, shock, moisture, EMI, RFI and magne c fi elds. • Analog or mul ple digital interface op ons.• Extremely low power op ons.

The DS-37 is suited to demanding applica on such as: aerospace, medical, instrumenta on, automa on, etc.

ELECTROMATEToll Free Phone (877) SERVO98

Toll Free Fax (877) SERV099www.electromate.com

[email protected]

Sold & Serviced By:

Page 2: Netzer ds 37-16-specsheet

Digital - SSi Interface (absolute posi on) DS-37-16-Dn-0

Output signal parameters Signal latency

(11)~250 μSec

Output code BinarySerial output SSi Diff eren al RS-422Clock SSi Diff eren al RS-422Monofl op me 25 μSecClock Frequency 0.5 ÷ 2.5 MHzMaximum payload 18 bit

Electrical parametersCurrent consump on ~ 180 mA

The na ve outputs signals are analog Sine / Cosine of the rota on angle. The digital outputs are obtained by using external modules. Synchronous Serial Interface (SSi) allows for serial transmission of absolute posi on data from the Electric Encoder™ responding to controller clock pulses. The Encoder and controller are linked by clock and data diff eren al signal lines.

Figure 1 illustrates the SSi ming diagram used by the Electric Encoder™ which is implemented in the addi onal digital electronics which provides advanced calibra on and monitoring op ons using the NCP (Netzer Communica on Protocol) using factory supplied so ware tools.

SC2SSi - Wires color code

# Name Color Func on 1 Clock + Grey SSi Clock2 Clock - Blue3 Data - Yellow SSi Data4 Data + Green5 GND Black Ground6 +5V Red Power supply

- 2 -

+5V

Host System

SC2S

Si

Inte

rpol

ator

SSi-CLK / NCP RX

SSi-CLK / NCP RX

SSi-DATA / NCP TX

SSi-DATA / NCP TX

5V

5V

120

6 (Red)

3 (Yellow)

4 (Green)

2 (Blue)

1 (Grey)

5 (Black)

+5V 6 (Red)

Gnd 1 (Black)

C/F 2 (Grey)

Sin 3 (Blue)

Vr 4 (Green)

Cos 5 (Yellow)

Elec

tric

Enc

oder

Gnd

A/D AlgorithmElectricangle

Electric Encoder Host system

Calibra on and analysis over NCP

SC2SSi external interpolator

Absoluteposi on

ELECTROMATEToll Free Phone (877) SERVO98

Toll Free Fax (877) SERV099www.electromate.com

[email protected]

Sold & Serviced By:

Page 3: Netzer ds 37-16-specsheet

n = total number of data bits. T = clock period (sec) - user defi ned.1/T = clock frequency 0.5 ÷ 2.5 MHz (user defi ned). t1 = minimum me required for the encoder to freeze data and preset the shi registers before receiving the fi rst rising edge to prompt the MSB t2 = data transmission delay (increases with cable length) t3 = required delay to refresh posi on data between subsequent posi on reads.

Digital - SSi interface (absolute posi on) DS-37-16-Dn-0

Posi on calibra on & signal analysis with SSi interface:

The Electric Encoder™ processing capabili es enable calibra on, built-in tests (BIT) and advanced setup, using the available so ware tools, such as:

A. Simple calibra on procedure using the SSi Explorer (CAA , Off sets , Zero posi on se ng). B. Field aid for valida ng proper mechanical moun ng.

Figure - 1

- 3 -

ELECTROMATEToll Free Phone (877) SERVO98

Toll Free Fax (877) SERV099www.electromate.com

[email protected]

Sold & Serviced By:

Page 4: Netzer ds 37-16-specsheet

Digital - AqB + Index interface (incremental) DS-37-16-Cn-0

Output signal parametersSignal latency

(11)250 μSec

Format Diff eren al RS-422Phase rela onship with CW sha rota on (as seen from top) A leads BIndex pulse width ½ A

Electrical parametersCurrent consump on ~ 130 mA

SC2AqB - Wires color code# Name Color Func on 1 GND Black Ground 2 +5V Red Supply voltage3 A+ Yellow

Quadrature outputs

4 A- Yellow/Black5 B+ Blue6 B- Blue / Black7 Z+ Orange

Index8 Z- White

- 4 -

Electric Encoder

A/D AqBinterpola on

Electricangle

SC2AqB interpolator AqB + Index

ELECTROMATEToll Free Phone (877) SERVO98

Toll Free Fax (877) SERV099www.electromate.com

[email protected]

Sold & Serviced By:

Page 5: Netzer ds 37-16-specsheet

Analog - Sine/Cosine output (absolute posi on) DS-37-16-00-0

Wires color code

# Name Color Func on 1 GND Black Ground2 C/F Grey Coarse / Fine3 Sine Blue Sine signal4 Vr Green V reference5 Cosine Yellow Cosine signal6 +5V Red Power supply

Output signal parameters Signal latency

(11)250 μSec

Fine-mode output noise (DC to 1kHz) (12)

100 μV (p-p)Fine-mode output amplitude

(13) 0.5V ± 20%

Coarse-mode output amplitude 0.5V ± 20% Phase rela onship (CW sha rota on - seen from top)

Sine leads Cosine

Signal bandwidth DC to 1 kHz

Coarse and Fine channels The DS-37 has two opera on modes: a Coarse-mode and a Fine-mode - equivalent to two separate encoders in a common housing. The modes are selectable by a logic C/F command; logic “0” (0V to +0.5V) selects the Coarse-mode, which has 3 Electrical Cycle/Revolu on (EC/R) while logic ”1” (+3V to +5V) selects the Fine-mode which has 16 EC/R. The switching me is less than 1 ms.

The Coarse-mode outputs need to be read only upon system ini a on a er which the encoder is permanently switched to the Fine mode. Coarse and Fine sine/cosine pairs are used to calculate the ini al absolute posi on, from that point tracking the Fine-channel outputs provides the absolute mechanical rota on angle with the specifi ed accuracy and resolu on. All output signals are referenced to an internally generated voltage Vr (~2.25V)

Absolute Posi on calcula on:

The analog Sine /Cosine outputs convey the electric angle of the Coarse or Fine signals. The absolute mechanical angle is computed by digi zing the analog signals and applying factory-supplied algorithms. Please refer to AN-02 and AN-03 .

Electrical parameters Output resistance <1 ΩCurrent consump on ~ 10 mA

(14)

- 5 -

Electric Encoder

A/D AlgorithmElectricangle

Host system

Absoluteposi on

ELECTROMATEToll Free Phone (877) SERVO98

Toll Free Fax (877) SERV099www.electromate.com

[email protected]

Sold & Serviced By:

Page 6: Netzer ds 37-16-specsheet

Notes1. The output signals are generated by the whole area of the rotor - see AN-01.2. Accuracy may degrade depending on moun ng tolerances and the Sine/Cosine amplitudes may exceed the A/D conversion range -see AN-023. The encoder includes an internal 4.5V LDO voltage regulator. 4. Standard DS encoders are insensi ve to ESD, stray magne c and capaci ve coupling from the host system current consump on. However it is advisable to allow a discharge path of no more than several tens of kΩ between the machine sha and the electronic’s ground, not leaving it electrically fl oa ng. 5. Consult factory.6. For higher ingress protec on the encoder should be mounted inside a sealed enclosure.7. The number of electrical sine/cosine cycles generated in one mechanical rota on.8. The angular resolu on is determined by the ra o of the Fine - channel amplitude and the encoder inherent noise – see AN-05.9. Not including dynamic error. For higher sta c accuracy consult factory. 10. Determined by the Fine-channel EC/Rs and the internal low pass fi lters, for higher rota on speed consult factory.11. An inherent signal delay inversely propor onal to the internal fi lter’s cut-off frequency (1 kHz, 3rd order Bessel) and resul ng in a dynamic error propor onal to the rota on speed - see AN-0512. For measuring the noise and valida ng the interconnec on see AN-02.13. With the rotor at its nominal axial posi on - see AN-02.14. For a micro-power version with current consump on down to 50 μA @ 3V consult factory.

Resolu on In bits Steps /360° mDeg /step Arc-sec /step mRad /step 14 16,384 21.9727 79.1016 0.383515 32,768 10.9863 39.5508 0.191716 65,536 5.4932 19.7754 0.095917 (DS-37) 131,072 2.7466 9.8877 0.047918 262,144 1.3733 4.9438 0.02419 524,288 0.6866 2.4719 0.01220 1,048,576 0.3433 1.236 0.006

Related documents:DS-37 Mechanical Installa on Guide

- 6 -

ELECTROMATEToll Free Phone (877) SERVO98

Toll Free Fax (877) SERV099www.electromate.com

[email protected]

Sold & Serviced By:

Page 7: Netzer ds 37-16-specsheet

- 7 -

DL Product line

ODEC/R

Outputs0 - Analog: Sine/Cosine

C - Digital : AqB + index (external module SC2AqB-00)D - Digital : SSi (external module SC2SSi-03)

BinaryResolu on CPR

Bit 12 13 14 15 16 17Code A B C D E F

32,76

8

16,3

84

8,19

2

4,09

6

65,53

613

1,072

DS - 37 - 16 - DF - 0

Loose wires 250mm

DecimalResolu on CPR

Bit 13 14 15 16 17Code K L M N O

32,00

0

16,0

00

8,00

0

64,00

012

8,000

Ordering

ELECTROMATEToll Free Phone (877) SERVO98

Toll Free Fax (877) SERV099www.electromate.com

[email protected]

Sold & Serviced By:

Page 8: Netzer ds 37-16-specsheet

Demo Units: Demo units with a rota ng sha are available with analog or digital outputs, USB based interface with the encoder and SSi explorer enable instant setup for demonstra on, integra on and analysis.CAT # : DKIT-DS-37-16-00-0 with analog output CAT # : DKIT-DS-37-16-CF-0 with AqB + Index output (using SC2AqB-00 module)CAT # : DKIT-DS-37-16-DF-0 with SSi output (using SC2SSi-03 module)

- 8 -

ELECTROMATEToll Free Phone (877) SERVO98

Toll Free Fax (877) SERV099www.electromate.com

[email protected]

Sold & Serviced By:


Recommended