New 3M Digital Projector · 2012. 8. 24. · 240V AC, 50/60 Hz).The use of other replacement lamps,...

3M™ Digital Projector

Management Application Guide Version 7.17 For Models: X21i / X26i / X30n / X31/ X31i / X35n / X36 / X36i / WX36 / WX36i / X46 / X46i / X56 / X62w / X64w / X70 / X75 / X80 / X90 / X90K / X90W / X95 / X95i

Revision History Revision Date Page(s) Changed Description of Change

4/2009 All pages First edition, models X70, X75, X80, X90, X95, X95i 4/2010 All pages Add models X62w, X64w, X30n, X35n 6/2010 All pages Add models X31, X36, X46 7/2010 All pages Add model WX36 12/2011 All pages Add model X56 3/2012 All pages Add model X21i / X26i 8/2012 All pages Add model X31i, X36i, X46i, WX36i

Intended Use The 3M™ Digital Projectors are designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and common line voltages (100V to 240V AC, 50/60 Hz).The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector, peripheral equipment and/or create a potentially unsafe operating condition. 3M Digital Projectors are designed to operate in a normal office environment.

• 100V - 240V AC, 50/60 Hz • 16° to 29° C (60° to 85° F) • 10-80% RH (without condensation) • 0-1828m (0-6000 feet) above sea level

The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can effect the operation or performance of the projector. The 3M logo and 3M are trademarks of the 3M Company. Other trademarks used herein are the properties of their respective owners.

Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.

Warranty and Limited Remedy3M warrants that when the 3M Product is used according to 3M’s Intended Use Statement (www.3M.com/meetings), it will perform satisfactorily for the warranted durability period as stated in the applicable 3M Product Manual in effect at the time of purchase. The warranties stated in the applicable 3M Product Manuals are exclusive and are made in place of any and all express or implied warranties or conditions, including any implied warranty of merchantability or fitness for a particular purpose, or any industry practice or custom or trade usage. Failure to follow the instructions contained in the appropriate 3M Product Manual or to use the 3M Product in accordance with 3M’s Intended Use Statement will void all warranties and limited remedies. EXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL, 3M SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, REVENUE OR BUSINESS) RESULTING FROM, OR IN ANY WAY RELATED TO PERFORMANCE, USE OR INABILITY TO USE ANY OF THE 3M PRODUCT. This limitation applies regardless of the legal theory upon which damages are sought. If 3M Product is defective within the applicable warranty period, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M Product or to refund the purchase price of the 3M Product. All replaced parts or products become property of 3M. If the 3M Product is repaired, 3M will repair the defective part(s) with a new or used part(s). If the 3M Product is replaced, 3M will replace the product with the same or equivalent model and with a new or refurbished product. In the case of an approved warranty claim, the replacement 3M Product will carry only the remaining term of the original 3M Product’s warranty period as stated in the applicable 3M Product Manual. For warranty service, you must provide proof of the date of the original purchase, otherwise the manufacturing code date will be used to establish the start date of the warranty. 3M Product Manuals include durability statements and may include limitations specific to the product(s) being used or its intended applications, which take precedence over any statement made here. Warranty terms, limitations and exclusions may differ outside the United States of America.

3M Mobile Interactive Solutions Division 6801 River Place Boulevard Tel: 1-800-328-1371 Austin, Texas 78726-9000 © 3M 2012. All Rights Reserved. www.3m.com/meetings 78-6971-1514-1 [Aug. 2012]

2

Contents

1 INTRODUCTION .................................................................................................................................... 4

1.1 OUTLINE ............................................................................................................................................ 4

1.2 SYSTEM .............................................................................................................................................. 4

2 INSTALLATION ..................................................................................................................................... 5

2.1 SYSTEM REQUIREMENTS .................................................................................................................... 5

2.2 PROJECTOR MANAGEMENT APPLICATION INSTALLATION .................................................................. 6

3 OPERATING INSTRUCTIONS .............................................................................................................. 8

3.1 CREATE LOGIN ACCOUNTS ................................................................................................................. 8

3.2 START APPLICATION ........................................................................................................................ 10

3.3 QUIT APPLICATION .......................................................................................................................... 10

3.4 MAIN SCREEN .................................................................................................................................. 11

3.5 ADD A GROUP OF PROJECTORS ......................................................................................................... 18

3.6 ADD AN INDIVIDUAL PROJECTOR ...................................................................................................... 18

3.7 DELETE A GROUP OR INDIVIDUAL PROJECTOR .................................................................................. 20

3.8 CHANGE A GROUP OR INDIVIDUAL PROJECTOR SETTINGS ................................................................. 20

3.9 COPY ................................................................................................................................................ 20

3.10 MOVE ........................................................................................................................................... 20

3.11 APPLYING ALARM / REMINDER SETTINGS TO PROJECTORS IN A GROUP ......................................... 21

3.12 UPDATE STATUS ........................................................................................................................... 21

3.13 SEARCH QUERIES (IN STATUS VIEW) ............................................................................................. 21

3.14 CONTROL THE PROJECTOR ............................................................................................................ 22

3.15 TURN ON THE POWER ................................................................................................................... 71

3.16 TURN OFF THE POWER .................................................................................................................. 71

3.17 DISPLAY MY IMAGE (E-SHOT) ..................................................................................................... 71

3.18 CHANGE FILTER MESSAGE ........................................................................................................... 71

3.19 SCHEDULE EVENTS ...................................................................................................................... 72

3.20 ACTIVATE MONITORING SCHEDULED EVENTS ............................................................................... 73

3.21 STOP MONITORING SCHEDULED EVENTS ....................................................................................... 73

3.22 POLLING INTERVAL PERIOD ......................................................................................................... 73

3.23 MAIL SETTING .............................................................................................................................. 74

3.24 MY IMAGE (E-SHOT) TRANSFER ................................................................................................ 76

3.25 USER-DEFINED MODEL ................................................................................................................ 77

3.26 OPEN THE BUILD-IN HTML PAGE IN THE PROJECTOR .................................................................. 80

3.27 SETUP PJMESSENGER TO PROJECTOR ......................................................................................... 81

3.28 ABOUT DIALOGUE ........................................................................................................................ 81

4 MAIL FEATURE ................................................................................................................................... 82

4.1 MAIL FORMAT .................................................................................................................................. 82

© 3M 2012. All Rights Reserved.

3

4.2 OTHERS ............................................................................................................................................ 82

5 STATUS ................................................................................................................................................. 83

6 OUTPUT LOG ....................................................................................................................................... 84

7 CREATE LOG REPORT ........................................................................................................................ 85

8 CREATE STATUS REPORT ................................................................................................................. 86

・ Microsoft and Windows is the registered trademark of Microsoft Corporation in the US and other countries. ・ Pentium is the registered trademark of Intel Corporation in the US and other countries. ・ All other trademarks are the property of their respected owners.

Warning ・ This software is free. The manufacturer has no responsibility for any errors that may occur while using this

software. ・ This software, or any product used with this software may not be used for any act which obstructs the

Maintenance of the International Peace and Safety.


4

1 Introduction

1.1 Outline Using the Projector Management Application allows you to use a single computer to control diagnose and monitor multiple projectors that are connected to the network or via an RS-232C cable.

1.2 System The following diagram shows a typical network diagram for the Projector Management Application.

Use a UTP cable category 5 or higher for a Local Area Network cable. Use a cross type cable when using a RS-232C serial cable.

HUB

RS-232C

LAN

RS-232C

LANLAN

LANLAN Ethernet / RS-232C Converter


5

2 Installation

2.1 System Requirements The following are the minimum system requirements of hardware and software to use the Projector Management Application.

(1) Operating System Windows 2000 Professional Windows XP Home Edition / Professional Windows Vista Home Basic / Home Premium / Business / Ultimate / Enterprise Windows 7 Starter / Home Basic / Home Premium / Professional / Ultimate / Enterprise

(2) CPU Pentium3 500MHz or higher

(3) Memory 256MB or higher

(4) Hard disk space Minimum 20MB free space for installation

(5) Serial port This port is required to control projectors by RS-232C

(6) LAN port This port is required to control projectors through a network


6

2.2 Projector Management Application Installation The following describes the installation process for the Projector Management Application:

(1) Double click the file “InstForPJMan.exe”.

(2) Select the language (English, Japanese or Chinese [Simplified]) during the installation process. And then click [OK].

(3) Click [Next].

(4) Read “License Agreement” and select “I accept the terms of the license agreement” and click [Next] if you agree the license agreement. Otherwise, click [Cancel] and stop the installation.

(5) Confirm the program folder, and then click [Next].


7

(6) Confirm the install folder and program folder again, and then click [Next].

(7) Click [Finish] to complete the Projector Management Application setup wizard.


8

3 Operating Instructions

3.1 Create login accounts The Projector Management Application requires a login name and password to launch the software. The Projector User Administration Tool helps you to create new user accounts.

3.1.1 How to launch

Double Click “PJUsrEdit.exe” that is located on same folder that you installed Projector Management Application. It automatically launches the Projector User Administration Tool, if no user accounts are created yet. Also Projector Management Application has a short cut [File] [User Configuration] to launch Projector User Administration Tool.

3.1.2 How to exit

Select [File] [Exit] from the menu or click [x] bottom of the top right corner. If the changes are made, you will be required to confirm the changes.

3.1.3 Main Window

(1) Menu

Menu Sub Menu Description File Save Save user data

Exit Exit Edit Add New User Create new user

Change User Edit user account Delete User Delete user account

(2) User List The status in the User List is described below.

Row name Description User Name Username (ID) Description Comment Man “●” shows that the user can access to the PJMan (Projector Management

Application). Ctrl “●” shows that the user can access to the PJCtrl (Projector Control Tool). Img “●” shows that the user can access to the PJImg (Projector Image Tool). FTP “●” shows that the user can access to the PJTransfer (Projector File Transfer Tool).

Menu

User List


9

3.1.4 Creating new user account

Select [Edit] [Add New User] or rights click on the user list and select [Add New User]. The following dialog window appears.

Press [OK] button after entering user name. The [Change Password] dialog appears. Enter new password and confirm entered password. The password is up to 20 characters and case sensitive.

3.1.5 Edit user account

Double click a username on the user list or select [Edit] [Change User] after choosing user to open edit dialog. You can edit username, description and accessibility (user rights). Click the button to change password. Enter old and new password, and re-enter new password to confirm.

3.1.6 Delete user account

Select [Edit] [Delete User] or rights click on the user list and select [Delete User]. The confirmation window will popup.

3.1.7 Save user account

Select [File] [Save]. The data is stored in the file, “C:\Program Files\Common Files\Projector Tools\config \UserList”.

User --- Define user name, up to 20 characters Description --- Add comments, up to 50 characters User Rights --- Define accessibility. It defines the

accessibility for the application software by each user account. The user can use allocation only marked application software.

Select All --- Select all application software. UnSel All --- Unselect all application software.


10

3.2 Start Application Select Windows [Start] [Program] [Projector Tools] [Projector Management Application]. The login window will then appear. Enter the username and password that was created by “Projector User Administration Tool”. After logged in, the following window will appear.

3.3 Quit Application Select [File] - [Exit] to quit. It is also possible to quit this software by clicking [x] on the top right corner of the window. When the confirmation dialogue appears, select [Yes] to finish.


11

3.4 Main Screen

(1) Menu Menus and Functions in the Main Screen are shown below.

Menu Sub Menu Function File Import Load the projector configuration file.

Export Save the projector configuration file. User Configuration Launch Projector User Administration Tool. Output Report Create the report. Log Log on / off. Log Report Create the log data report. Exit Quit this application.

Edit Add Group Add Group. Add Projector Add projectors which user is going to manage. Discovery Discover projectors. Delete Delete the projectors or groups that are selected from tree. Edit Edit the registered information of the projectors or groups that

are chosen from tree. Cut Cut the selected projector on the tree view. Copy Copy the selected projector on the tree view. Paste Paste projectors. Alarm Time Settings Set / Edit the period of the lamp and filter hours reminder.

View Refresh Refresh the status of the projectors or groups that are chosen from the tree.

Search Edit the search query. Schedule Select on / off for the Schedule view.

Control Projector Control Control the selected group of projector, or the selected projector.

Power ON Power ON the projectors which are selected from the tree, or the projectors which belong to a group which is chosen from the tree.

Power OFF Power OFF the projectors which are selected from the tree, or the projectors which belong to a group which is chosen from the tree.

Display Image Select My Image (e-SHOT) image to display. Execute Command Control User-defined model. Filter Message Change filter message setting.

Schedule Edit Edit the Schedule settings. Start Start Schedule execution. Stop Stop Schedule execution.

Option Status Check Interval Set the Status Check Interval. Mail Settings Configure the Mail Settings. Send Image Transfer My Image (e-SHOT) image to projectors. Edit User-defined Model Edit User-defined model information. Access Projector via HTML Open the internal HTML page with default Internet browser. Send Messenger data Transfer Messenger data to projectors.

Help About Projector Management Application

Displays the version of this application.


12

(2) Toolbar The functions of these icons correspond with the menus as follows:

Icon Menu

[Edit]-[Add Group]

[Edit]-[Add Projector]

[Edit]-[Delete]

[Edit]-[Edit]

[Edit]-[Cut]

[Edit]-[Copy]

[Edit]-[Paste]

[View]-[Refresh]

[Control]-[Power ON]

[Control]-[Power OFF]

[Schedule]-[Start]

[Schedule]-[Stop]

[Help]-[About Projector Management Application]


13

(3) Status Group PJMan provides two pre-defined projector views, and the flexible views that are based on the search queries.

(a) All Projectors View Shows the list of all projectors that are defined in the PJMan software.

(b) Error / Warning View Shows the list of projectors that are ONLY in Error or Warning state.

(c) Find Result View Shows the multiple lists of projectors based on the given search queries (described in a later section).

Projector Name --- Displays the projector name. Model --- Displays the model name. Connection --- Displays the connection information.

(IP address and MAC address / COM port) MAC Address --- Displays the MAC address. Power --- Displays the power status (ON / STANDBY). Input --- Displays the input source. Status --- Displays the error status. Lamp Time --- Displays the current lamp time. Filter Time --- Displays the current filter time. Total Run Time --- Displays the total run time.


14

(d) Projectors Group View Shows the list of groups and projectors in the selected group.

Group Name --- Displays the group name. Contains --- Displays the number of projectors and groups in the group. Comment --- Displays the comment. Projector Name --- Displays the projector name. Model --- Displays the model name. Connection --- Displays the connection information.



15

(e) Individual Projector View Shows the status of selected projector.

Projector Name --- Displays the projector name. Model --- Displays the model name. Comment --- Displays the comment.

Projector Name --- Displays the projector name. Model --- Displays the model name. Connection --- Displays the connection information.



16

(4) Schedule View

(a) For a group of projectors

Group Path --- Shows the full path name of selected group. Current Date & Time --- Displays the current date and time. Date --- Displays the activation date. Time --- Displays the activation time. Control --- Displays the execute command.

Group Path Current Date & Time


17

(b) For an individual projector

Group Path --- Shows the full path name of selected projector. Current Date & Time --- Displays the current date and time. Date --- Displays the activation date. Time --- Displays the activation time. Control --- Displays the execute command.

Projector Path Current Date & Time


18

3.5 Add a group of projectors You can define a group of projectors into the tree view. Select [Edit] [Add Group] to add a group.

Group Name --- Enter a group name up to 256 characters. Comment --- Enter a comment up to 256 characters.

Note: The maximum depth of sub groups is five levels.

3.6 Add an individual projector You can define an individual projector into the tree view. Select [Edit] [Add Projector] to add a projector.

Projector Name --- Enter a projector name up to 256 characters. Model --- Select a model. Add Model --- Add new User-defined model. Please see the section 3.20 for details. Comment --- Enter a comment up to 256 characters. Connection --- Select a connection method. RS-232C --- Select when using RS-232C, and set COM Port. NETWORK --- Select when using network, and set IP Address and Port No.

Network Port No. of PL75X, PL80X, X70, X75, X75C, X75K, X80, X80C and X80K is 23. Network Port No. of CL33X, CL35X, CL67N, CL69N, CL72X, CL73W, CL73X, CL86X,

NE7, PL90X, PL92X, PL93X, PL95X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X62w, X64w, X90, X90K, X90w, X95, X95K, X95i, X95iK is 23 or 9715.

The authentication of commands is available for CL33X, CL35X, CL67N, CL69N, CL72X, CL73W, CL73X, CL86X, NE7, PL90X, PL92X, PL93X, PL95X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X62w, X64w, X90, X90K, X90w, X95, X95K, X95i and X95iK.

The authentication of My Image (e-SHOT) feature is available for CL33X, CL35X, CL67N, CL69N, CL72X, CL73W, CL73X, CL86X, NE7, PL90X, PL92X, PL93X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X90 and X90K.

The password for the both authentications above is common. [Discovery] --- User can search for the projector (CL33X, CL35X, CL67N, CL69N, CL72X,

CL73W, CL73X, CL86X, NE7, PL90X, PL92X, PL93X, PL95X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X62w, X64w, X90, X90K, X90w, X95, X95K, X95i, X95iK) when it is connected to the network.

Status Check --- Check the check box if you want to enable the status polling. If it is not checked, the projector is ignored from the status check process and won’t show up in the status list. It is registered in PJMan, but it excludes from the current status monitoring list.

Lamp Alarm Time --- Define the lamp alarm / reminder period. The setting is effective for individual projector. If you don’t want to enable this function, please set 0 hours.

Filter Alarm Time --- Define the filter alarm / reminder period. The setting is effective for individual projector. If you don’t want to enable this function, please set 0 hours.


19

The discovery feature allows you to search projectors on the network automatically. The discovery works when you are selecting a group or root. Select [Edit] [Discovery] from the menu. The discovery window is shown below. Click start button to begin the discovery process.

For searching certain IP address range, please specify the IP address range to enter Start and End address, and then check the checkbox ”Specify an address range and search” and click the [Start] button. It will take several minutes depending upon the number of IP addresses needed to be scanned.

When discovery finds projectors, the list of projectors is shown and [Register] button becomes available. You can register multiple projectors at the same time. When the [Register] button is clicked, the projector is added under the group or root that you have selected. The projector name and model is automatically assigned. Please edit the name and model as needed. [NOTE]

Windows Security Alert will be shown on your display when the discovery function activates, if Windows Firewall is “On” (Windows XP SP2 or later). Please choose “Unblock” to add the software onto the exception list. Other firewall security software may block the discovery function. In that case, please add the software to the safe list or disable firewall software when you use discovery function.


20

3.7 Delete a group or individual projector You can delete a group of projectors or an individual projector. Click a group or projector in the tree view, select [Edit] [Delete]. You can also delete a group or projector by clicking the delete icon on the toolbar. When the confirmation dialogue appears, select [OK] to delete.

3.8 Change a group or individual projector settings You can change a group or individual projectors settings. Click a group on the tree view, select [Edit] [Edit]. Or Click a projector, select [Edit] [Edit]. You can also change settings by clicking the edit icon on the toolbar. The ‘Edit Group’ or ‘Edit Projector’ screen is shown below. Content to be set is same as ‘Add Group’ or ‘Add Projector’ screen.

3.9 Copy You can copy the projector from the tree view. Select [Edit] [Copy] on the menu after choosing a projector from the tree view. You can paste copied projectors by selecting [Edit] [Copy] from the menu or click the “Paste” button on the tool bar. Also you can copy projectors by drag and drop by holding down Ctrl key. Note that you cannot copy projectors if the name is the same of the destination projector.

3.10 Move You can move projectors in the tree view. Select [Edit] [Cut] on the menu or click “Cut” on the tool bar after choosing projectors on the tree view. You can paste copied projectors by selecting [Edit] [Copy] from the menu or by clicking the “Paste” button on the tool bar. You can also drag and drop projectors onto another projector group.


21

3.11 Applying alarm / reminder settings to projectors in a group You can set alarm / reminder settings to multiple projectors in a group at the same time. Select the group that you want to set the alarm / reminder for and then select [Edit] [Alarm Time Setting] from the menu. The Alarm Time Settings dialogue will appear. Check the checkbox and enter the hours that the alarm / reminder will be activated. If you apply new settings to the group, the individual alarm / reminder setting on each projector will be overwritten.

3.12 Update Status Select [View] [Refresh] to update status of a group or individual projector. This function only works when the status tab is displayed.

3.13 Search queries (in Status view) In order to make the search queries, select [View] [Search] from the menu. The Search dialogue will appear.

Connection --- Search by connection type. IP Address --- Search by IP address range. Power --- Search by projector power status. Status --- Search by error / warning status. Lamp Time --- Search by lamp hours. Filter Time --- Search by filter hours. Total Run Time --- Search by total operation hours. All or part of the projector name --- Search by projector name.

The search group will be added to the Search Result tree, when you press [Search] bottom with given query. The list of projectors that are matched with your search query will be shown in the Status View.


22

3.14 Control the projector Select [Control] [Projector Control] to control the projector. The controllable functions will be depending upon what group or projector is selected. (a) In case of All Projectors selected

Power --- Turn on / off power for a group of projectors. Input Source --- Change input source. Whisper --- Change Whisper / Eco mode. Blank --- Change blank on / off. Mute --- Change sound mute status. Freeze --- Change freeze status. Display Image --- Select My Image (e-SHOT) to display / OFF. Messenger --- Select Messenger to display / OFF.

(b) In case of Error/ Warning selected



23

(c) In case of Search Result item selected


(d) In case of a group selected

Group Information

Group Name --- Displays the group name. Contains --- Displays the number of projectors and groups in the group. Comment --- Displays the comment.



24

(e) In case of an individual projector is selected

Projector Information

Projector Name --- Displays the projector name. Model --- Displays the model name. Comment --- Displays the comment.

Power --- Turn on / off power for a group of projectors. Input Source --- Change input source. Aspect --- Change aspect ratio. Whisper --- Change Whisper / Eco mode. Mirror --- Change mirror status. Blank --- Change blank on / off. Mute --- Change sound mute status. Freeze --- Change freeze status. Display Image --- Select My Image (e-SHOT) to display / OFF. Messenger --- Select Messenger to display / OFF. Brightness --- Change brightness.

[-]: Decrease value. [+]: Increase value.

Contrast --- Change contrast. [-]: Decrease value. [+]: Increase value.

Sharpness --- Change sharpness. [-]: Decrease value. [+]: Increase value.

Color --- Change color. [-]: Decrease value. [+]: Increase value.

Tint --- Change tint. [-]: Decrease value. [+]: Increase value.

Auto Adjust --- Execute auto image adjustment. Lamp Time Reset --- Reset the lamp time. Filter Time Reset --- Reset the filter time. Advanced Control --- Open the projector Advance Control Menu.

(‘Advanced Control’ Screen varies depending on the projector model.)


25

The details for each Advance Control screen (for the appropriate projector model types) are described below.

■ PL80X / X70 / X80 / X80C / X80K [STATUS] Tab

Function General Description Power Displays the current power status.

Off / On / Cool down Input Source Displays the current input source.

M1-D / RGB / BNC / Video / S-Video / Component Error Status Displays the current error status.

Normal / Cover Error / Fan Error / Lamp Error / Temp Error / Air Flow Error / Lamp Time Error / Cold Error / Filter Error / Other Error

Blank On /Off Displays the current blank on/off status. Off / On

Mute Displays the current mute status. Off / On

Freeze Displays the current freeze status. Normal / Freeze

Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current filter. Reset Initialize the selected function.

Lamp Time / Filter Time [Execute]: After the confirmation message, the selected function will be initialized.

[MAIN] Tab

Function General Description Bright Adjusts the brightness.

[-]: Decrease the brightness value. [+]: Increase the brightness value.

Contrast Adjusts the contrast. [-]: Decrease the contrast value. [+]: Increase the contrast value.

Aspect Switches the mode for aspect ratio. 4:3 / 16:9 / Small / Normal

Whisper Turn off/on the whisper mode. Normal / Whisper

Mirror Switches the mode for mirror status. Normal / H:Invert / V:Invert / H&V:Invert

Language Switches the menu language. English / French / German / Spanish / Italian / Norwegian / Dutch / Portuguese / Japanese / Simplified Chinese / Korean / Swedish / Russian / Finnish / Polish

Reset Initialize the selected function. Bright / Contrast

[Execute]: After the confirmation message, the selected function will be initialized.


26

[PICTURE-1] Tab

Function General Description Gamma Switches the gamma mode.

Normal / Cinema / Dynamic / Custom Custom Gamma Adjusts the gamma data.

[-]: Decrease the gamma value. [+]: Increase the gamma value.

Color Temp Switches the color temperature mode. Low / Middle / High / User

Custom User R Adjusts the red color level for the user mode of red color temperature. 100 / 90 / 80 / 70 / 60 / 50

Custom User G Adjusts the green color level for the user mode of green color temperature. 100 / 90 / 80 / 70 / 60 / 50

Custom User B Adjusts the blue color level for the user mode of blue color temperature. 100 / 90 / 80 / 70 / 60 / 50

Color Bal R Adjusts the red color balance. [-]: Decrease the red color balance value. [+]: Increase the red color balance value.

Color Bal G Adjusts the green color balance. [-]: Decrease the green color balance value. [+]: Increase the green color balance value.

Color Bal B Adjusts the blue color balance (blue). [-]: Decrease the blue color balance value. [+]: Increase the blue color balance value.

Sharpness Adjusts the sharpness. [-]: Decrease the sharpness value. [+]: Increase the sharpness value

Color Adjusts the strength of whole color. [-]: Decrease the color value. [+]: Increase the color value

Tint Adjusts the tint. [-]: Decrease the tint value. [+]: Increase the tint value.

My Memory Loads the data from the memory. Load1 / Load2 / Load3 / Load4

Saves the current adjustment data into the memory. Save1 / Save2 / Save3 / Save4

[Execute]: Performs each function. Reset Initialize the selected function.

Color Bal R / Color Bal G / Color Bal B / Sharpness / Color / Tint [Execute]: After the confirmation message, the selected function will be initialized.

[PICTURE-2] Tab

Function General Description Position Adjust the display position.

[ ]: Increase the vertical position value. [ ]: Decrease the vertical position value. [ ]: Increase the horizontal position value. [ ]: Decrease the horizontal position value.

H Phase Adjust the horizontal phase to eliminate flicker. [-]: Decrease the horizontal phase value. [+]: Increase the horizontal phase value.

H Size Adjust the horizontal size. [-]: Decrease the horizontal size value. [+]: Increase the horizontal size value.

Over Scan Adjust the over-scan ratio. [-]: Decrease the over-scan value. [+]: Increase the over-scan value.

Reset Initialize the selected function. V Position / H Position / H Size / Over Scan



27

[INPUT] Tab

Function General Description Color Space Switches the mode for color space.

Auto / RGB / SMPTE240 / REC709 / REC601 Component Switches the function of the COMPONENT port.

Component / Scart RGB Video Format Switches the mode for video format.

Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL 3D-YCS Turns off/on the 3D-YCS.

Off / On Video NR Switches the noise reduction mode.

Low / Middle / High S2-Aspect Turns off/on the S2-aspect function

Off / On P.IN P. Input Switches the signal input port for the child window.

Video / S-Video P.IN P. Position Switches the display position of the child window.

Upper Left / Upper Right / Bottom Left / Bottom Right P.IN P. Audio Switches the audio source of the child window.

RGB / Video P.IN P. Size Switches the display size of the child window.

Off / Large / Small Power Up Input Switches the signal input port to display just when the projector is turned on.

Last Input / M1-D / RGB / BNC / Component / S-Video / Video

[AUTO] Tab

Function General Description Adjust [Execute]: Performs the automatic adjustment feature. Power Off Adjusts the time to count down to automatically turn the projector off.

[-]: Decrease auto power off time. [+]: Increase auto power off time.

Power On Turns off/on the auto power on function. Off / On

Search Turns off/on the automatic signal search function. Off / On

[SCREEN] Tab

Function General Description Blank Switches the mode for the blank screen.

Blue / White / Black / MyScreen / Original Start Up Switches the mode for the start-up screen.

Original / Off / MyScreen MyScreen Size Switches the size of the MyScreen.

Full / x1 MyScreen Lock Turn off/on the MyScreen lock function.

Off / On Menu Position Adjusts the menu position.

[ ]: Increase the vertical menu position value. [ ]: Decrease the vertical menu position value. [ ]: Decrease the horizontal menu position value. [ ]: Increase the horizontal menu position value.

Message Turns off/on the message function. Off / On

Reset Initialize the selected function. Menu Position V / Menu Position H



28

[OPTION] Tab

Function General Description Volume Adjusts the volume.

[-]: Decrease the volume value. [+]: Increase the volume value.

Speaker Turns off/on the built-in speaker. Off / On

IR Remote Turns off/on the remote sensor. Front (Off / On) Rear (Off / On) Top (Off / On)

IR Remote ID Switches the number as an ID number for remote control. All / 1 / 2 / 3

Auto Adjust Switches the auto adjustment enable function. Disable / Enable

Lens Type Switches the lens type currently used. Auto / 1 / 2 / 3 / 4 / 5

Lens Lock Turns off/on the lens lock function. Off / On

[OTHER] Tab

Function General Description Power Turns off/on the power.

Off / On Input Source Switchs the input source.

M1-D / RGB / BNC / Video / S-Video / Component Blank On / Off Turns off/on the blank.

Off / On Mute Turns off/on the mute.

Off / On Freeze Turn off/on the freeze.

Normal / Freeze Magnify Adjusts the magnify setting.

[-]: Decrease the magnify value. [+]: Increase the magnify value.

Keystone V Adjusts the vertical keystone distortion. [-]: Decrease the vertical keystone value. [+]: Increase the vertical keystone value.

Keystone H Adjusts the horizontal keystone distortion. [-]: Decrease the horizontal keystone value. [+]: Increase the horizontal keystone value.

Reset Initialize the selected function. Keystone V / Keystone H



29

■ PL75X / X75 / X75C / X75K [STATUS] Tab



DVI / RGB1 / RGB2 / Video / S-Video / Component Error Status Displays the current error status.

Normal / Cover Error / Fan Error / Lamp Error / Temp Error / Air Flow Error / Lamp Time Error / Cold Error / Filter Error / Other Error

Blank On / Off Displays the current blank on/off status. Off / On





[PICTURE] Tab

Function General Description Bright Adjusts the brightness.



Gamma Switches the gamma mode. #1-Custom / #2-Custom / #3-Custom / #1-Default / #2-Default / #3-Default

Color Temp Switches the mode of color temperature. Low / Middle / High / Custom



Sharpness Adjusts the sharpness. [-]: Decrease the sharpness value. [+]: Increase the sharpness value.

My Memory Loads the data on the memory. Load1 / Load2 / Load3 / Load4


[Execute]: Performs each function. Reset Initialize the selected function

Bright / Contrast / Color / Tint / Sharpness [Execute]: After the confirmation message, the selected function will be initialized.


30

Gamma - Custom -

Function General Description User Gamma Pattern Changes the test pattern.

Off / 9 steps Gray scale / 15 steps Gray scale / Ramp User Gamma Point 1 Adjusts the user gamma point 1.

[-]: Decrease the user gamma point 1 value. [+]: Increase the user gamma point 1 value.

User Gamma Point 2 Adjusts the user gamma point 2. [-]: Decrease the user gamma point 2 value. [+]: Increase the user gamma point 2 value.







Color Temp - Custom -


Off / 9 steps Gray scale / 15 steps Gray scale / Ramp Color Temp Gain R Adjusts the red color temperature gain.

[-]: Decrease the red color temp gain value. [+]: Increase the red color temp gain value.

Color Temp Gain G Adjusts the green color temperature gain. [-]: Decrease the green color temp gain value. [+]: Increase the green color temp gain value.

Color Temp Gain B Adjusts the blue color temperature gain. [-]: Decrease the blue color temp gain value. [+]: Increase the blue color temp gain value.

Color Temp Offset R Adjusts the red color temperature offset. [-]: Decrease the red color temperature offset value. [+]: Increase the red color temperature offset value

Color Temp Offset G Adjusts the green color temperature offset. [-]: Decrease the green color temperature offset value. [+]: Increase the green color temperature offset value

Color Temp Offset B Adjusts the blue color temperature offset. [-]: Decrease the blue color temperature offset value. [+]: Increase the blue color temperature offset value

[IMAGE] Tab

Function General Description Aspect Switches the mode for aspect ratio.

4:3 / 16:9 / Small / Normal Over Scan Adjusts the over-scan ratio.

[-]: Decrease the over-scan value. [+]: Increase the over-scan value.

Position Adjusts the display position. [ ]: Increase the vertical position value. [ ]: Decrease the vertical position value. [ ]: Increase the horizontal position value. [ ]: Decrease the horizontal position value.

H Phase Adjusts the horizontal phase to eliminate flicker. [-]: Decrease the horizontal phase value. [+]: Increase the horizontal phase value.

H Size Adjusts the horizontal size. [-]: Decrease the horizontal size value. [+]: Increase the horizontal size value.

Auto Adjust [Execute]: Performs the automatic adjustment feature. Reset Initialize the selected function.

Over Scan / V Position / H Position / H Size [Execute]: After the confirmation message, the selected function will be initialized.


31

[VIDEO QLTY.] Tab

Function General Description Progressive

Switches the progress mode. Off / TV / Film

3D-YCS Switches the 3D-YCS mode. Off / Normal / Still Image

Video NR Switches the noise reduction mode. Low / Middle / High

[INPUT] Tab

Function General Description Color Space Switches the mode for color space.

Auto / RGB / SMPTE240 / REC709 / REC601 Component Switches the function of COMPONENT VIDEO port.

Component / Scart RGB Video Format Switches the mode for video format.

Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL DVI Select a signal source of the DVI-D port.

DVD / Computer

[SETUP] Tab

Function General Description Whisper Turns off/on the whisper mode.

Normal / Whisper Mirror Switches the mode for mirror status.

Normal / H:Invert / V:Invert / H&V:Invert Volume Adjusts the volume.


Stereo Switches the internal speaker output mode. Mono / Stereo

IR Remote Turns off/on the remote sensor. Front (Off / On) Top (Off / On)

[SCREEN] Tab

Function General Description Language Switches the OSD (On Screen Display) language.

English / French / German / Spanish / Italian / Norwegian / Dutch / Portuguese / Japanese / Simplified Chinese / Korean / Swedish / Russian / Finnish / Polish / Turkish / Traditional Chinese

Menu Position Adjusts the menu position. [ ]: Increase the vertical menu position value. [ ]: Decrease the vertical menu position value. [ ]: Decrease the horizontal menu position value. [ ]: Increase the horizontal menu position value.

OSD Bright. Switches the brightness level of the OSD (On Screen Display). [-]: Decrease the OSD brightness value. [+]: Increase the OSD brightness value.

Blank Switches the mode for the blank screen. Blue / White / Black / MyScreen / Original

Start Up Switches the mode for the start-up screen. Original / Off / MyScreen

MyScreen Lock Turns off/on the MyScreen lock function. Off / On




[OPTION] Tab

Function General Description One Touch Turns off/on the automatic keystone correction function.

Off / On Auto Search Turns on/off the automatic signal search function.

Off / On Auto Off Adjusts the time to count down to automatically turn the projector off.

[-]: Decrease the auto power off time. [+]: Increase the auto power off time.

Auto Adjust Disable/Enable the automatic adjustment. Disable / Enable


32

[OTHER] Tab

Function General Description Power Turns off/on the Power.

Off / On Input Source Switches the input source.

DVI / RGB1 / RGB2 / Video / S-Video / Component Mode Switches the mode of picture type.

Normal / Cinema / Dynamic / Custom Custom is displayed only. It cannot be set.

Blank On / Off Turns off/on the blank. Off / On

Mute Turns off/on the mute. Off / On

Freeze Turns off/on the freeze. Normal / Freeze

Magnify Adjusts the magnify setting. [-]: Decrease the magnify value. [+]: Increase the magnify value.

Keystone V Adjusts the vertical keystone distortion. [-]: Decrease the vertical keystone value. [+]: Increase the vertical keystone value.

Keystone H Adjusts the horizontal keystone distortion. [-]: Decrease the horizontal keystone value. [+]: Increase the horizontal keystone value.

Auto Keystone [Execute]: Performs the automatic keystone distortion correction.

Reset Initialize the selected function. Keystone V / Keystone H



33

■ PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K / X95i / X95iK [STATUS] Tab



X62w RGB1 / RGB2 / Video / S-Video / Component / MIU

X64w Computer1 / Computer2 / Video / S-Video / Component / MIU

PL90X / X90 / X90K RGB1 / RGB2 / M1-D / Video / S-Video / Component

X90w RGB1 / RGB2 / M1-D / Video / S-Video / Component / MIU

PL95X / X95 / X95K / X95i / X95iK RGB1 / RGB2 / HDMI / Video / S-Video / Component / MIU

Error Status Displays the current error status. Normal / Cover Error / Fan Error / Lamp Error / Temp Error / Air Flow Error / Lamp Time Error / Cold Error / Filter Error / Other Error

Blank On / Off Displays the current blank on/off status. Off / On





[PICTURE] Tab

Function General Description Brightness Adjusts the brightness.



Gamma Switches the gamma mode. PL90X / X62w / X90 / X90K / X90w

#1-Custom / #2-Custom / #3-Custom / #4-Custom / #5-Custom / #1-Default / #2-Default / #3-Default / #4-Default / #5-Default

PL95X / X64w / X95 / X95K / X95i / X95iK #1-Custom / #2-Custom / #3-Custom / #4-Custom / #5-Custom / #6-Custom / #1-Default / #2-Default / #3-Default / #4-Default / #5-Default / #6-Default

Color Temp Switches the color temperature mode. PL90X / X62w / X90 / X90K / X90w

High / Mid / Low / Hi-Bright-1 / Hi-Bright-2 / Custom-High / Custom-Mid / Custom-Low / Custom-Hi-Bright-1 / Custom-Hi-Bright-2

PL95X / X64w / X95 / X95K / X95i / X95iK High / Mid / Low / Hi-Bright-1 / Hi-Bright-2 / Hi-Bright-3 / Custom-High / Custom-Mid / Custom-Low / Custom-Hi-Bright-1 / Custom-Hi-Bright-2 / Custom-Hi-Bright-3




Active Iris Changes the active iris control mode. Off / Theater / Presentation

This function is not displayed for X62w / X64w. My Memory Loads the data from the memory.

Load1 / Load2 / Load3 / Load4 Saves the current adjustment data into the memory.

Save1 / Save2 / Save3 / Save4 [Execute]: Performs each function.

Reset Initialize the selected function Brightness / Contrast / Color / Tint / Sharpness



34

Gamma - Custom -


Off / 9 steps Gray scale / 15 steps Gray scale / Ramp User Gamma Point 1 Adjusts the user gamma point 1.

[-]: Decrease the user gamma point 1 value. [+]: Increase the user gamma point 1 value. [Reset]: Initialize the user gamma point 1 value.

User Gamma Point 2 Adjusts the user gamma point 2. [-]: Decrease the user gamma point 2 value. [+]: Increase the user gamma point 2 value. [Reset]: Initialize the user gamma point 2 value.










[-]: Decrease the red color temperature gain value. [+]: Increase the red color temperature gain value. [Reset]: Initialize the red color temperature gain value.

Color Temp Gain G Adjusts the green color temperature gain. [-]: Decrease the green color temperature gain value. [+]: Increase the green color temperature gain value. [Reset]: Initialize the green color temperature gain value.

Color Temp Gain B Adjusts the blue color temperature gain. [-]: Decrease blue red color temperature gain value. [+]: Increase the blue color temperature gain value. [Reset]: Initialize the blue color temperature gain value.

Color Temp Offset R Adjusts the red color temperature offset. [-]: Decrease the red color temperature offset value. [+]: Increase the red color temperature offset value. [Reset]: Initialize the red color temperature offset value.

Color Temp Offset G Adjusts the green color temperature offset. [-]: Decrease the green color temperature offset value. [+]: Increase the green color temperature offset value. [Reset]: Initialize the green color temperature offset value.

Color Temp Offset B Adjusts the blue color temperature offset. [-]: Decrease the blue color temperature offset value. [+]: Increase the blue color temperature offset value. [Reset]: Initialize the blue color temperature offset value.


35

[IMAGE] Tab


4:3 / 16:9 / 14:9 / Small / Normal Over Scan Adjusts the over-scan ratio

[-]: Decrease the over-scan value. [+]: Increase the over-scan value.






[INPUT] Tab

Function General Description Progressive Switches the progress mode.

Off / TV / Film Video NR Switches the noise reduction mode.

Low / Mid / High 3D-YCS Switches the 3D-YCS mode.

Off / Movie / Still This function is not displayed for X62w / X64w.

Color Space Switches the mode for color space. Auto / RGB / SMPTE240 / REC709 / REC601

Component Switches the function of the COMPONENT port. Component / Scart RGB

Video Format - Video Switches the mode for video format of the VIDEO port. Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL

Video Format – S-Video Switches the mode for video format of the S-VIDEO port. Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL

HDMI Changes the HDMI signal mode. Auto / Normal / Enhanced

This function is not displayed for PL90X / X62w / X64w / X90 / X90K / X90w. M1-D Changes the M1-D signal mode.

Normal / Enhanced This function is not displayed for PL95X / X62w / X64w / X95 / X95K / X95i / X95iK.

Frame Lock Turns off/on the frame lock function. Off / On

This function is not displayed for PL95X / X64w / X95 / X95K / X95i / X95iK. Frame Lock - RGB1 Turns the frame lock function off/on of the RGB IN1 port.

Off / On This function is not displayed for PL90X / X62w / X64w / X90 / X90K / X90w.

Frame Lock-Computer1 Turns the frame lock function off/on of the COMPUTER IN1 port. Off / On

This function is not displayed for PL90X / PL95X / X62w / X90 / X90K / X90w / X95 / X95K / X95i / X95iK.

Frame Lock - RGB2 Turns the frame lock function off/on of the RGB IN2 port. Off / On

This function is not displayed for PL90X / X62w / X64w / X90 / X90K / X90w. Frame Lock-Computer2 Turns the frame lock function off/on of the COMPUTER IN2 port.

Off / On This function is not displayed for PL90X / PL95X / X62w / X90 / X90K / X90w / X95 / X95K / X95i /

X95iK. Frame Lock - HDMI Turns the frame lock function off/on of the HDMI port.

Off / On This function is not displayed for PL90X / X62w / X64w / X90 / X90K / X90w.

RGB in - RGB1 Selects the RGB input signal type of the RGB IN1 port. PL95X / X95 / X95K / X95i / X95iK

Sync On G Off / Auto PL90X / X62w / X90 / X90K / X90w

Sync On G Off / Sync On G On This function is not displayed for X64w.

Computer in-1 Selects the computer input signal type of the COMPUTER IN1 port. Sync On G Off / Sync On G On



36

RGB in - RGB2 Selects the RGB input signal type of the RGB IN2 port.

PL95X / X95 / X95K / X95i / X95iK Sync On G Off / Auto

PL90X / X62w / X90 / X90K / X90w Sync On G Off / Sync On G On

This function is not displayed for X64w. Computer in-2 Selects the computer input signal type of the COMPUTER IN2 port.

Sync On G Off / Sync On G On This function is not displayed for PL90X / PL95X / X62w / X90 / X90K / X90w / X95 / X95K / X95i /

X95iK.

[SETUP] Tab

Function General Description Auto Keystone [Execute]: Performs the automatic keystone distortion. Keystone V Corrects the vertical keystone distortion.

[-]: Decrease the vertical keystone value. [+]: Increase the vertical keystone value.

Keystone H Corrects the horizontal keystone distortion. [-]: Decrease the horizontal keystone value. [+]: Increase the horizontal keystone value. This function is not displayed for X62w / X64w.

Whisper Turns off/on the whisper mode. Normal / Whisper


Volume Adjusts the volume. [-]: Decrease the volume value. [+]: Increase the volume value. This function is not displayed for PL90X / PL95X / X90 / X90K / X90w / X95 / X95K / X95i / X95iK.



Audio RGB1 Assigns the audio port when the RGB IN1 input port is selected. Off / Audio1 / Audio2 / Audio3


Audio-Computer1 Assigns the audio port when the COMPUTER IN1 input port is selected. Off / Audio1 / Audio2 / Audio3


Audio RGB2 Assigns the audio port when the RGB IN2 input port is selected. Off / Audio1 / Audio2 / Audio3


Audio-Computer2 Assigns the audio port when the COMPUTER IN2 input port is selected. Off / Audio1 / Audio2 / Audio3


Audio Video Assigns the audio port when the VIDEO input port is selected. Off / Audio1 / Audio2 / Audio3

This function is not displayed for PL90X / PL95X / X90 / X90K / X90w / X95 / X95K / X95i / X95iK. Audio S-Video Assigns the audio port when the S-VIDEO input port is selected.

Off / Audio1 / Audio2 / Audio3 This function is not displayed for PL90X / PL95X / X90 / X90K / X90w / X95 / X95K / X95i / X95iK.

Audio Component Assigns the audio port when the COMPONENT input port is selected. Off / Audio1 / Audio2 / Audio3

This function is not displayed for PL90X / PL95X / X90 / X90K / X90w / X95 / X95K / X95i / X95iK. Audio MIU Assigns the audio port when the MIU input port is selected.

Off / Audio1 / Audio2 / Audio3 / Audio MIU This function is not displayed for PL90X / PL95X / X90 / X90K / X90w / X95 / X95K / X95i / X95iK.

Monitor Out-RGB1 Assigns the MONITOR OUT when the RGB IN1 input port is selected. Off / RGB1

This function is not displayed for PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K. Monitor Out-RGB2 Assigns the MONITOR OUT when the RGB IN2 input port is selected.

Off / RGB2 This function is not displayed for PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K.

Monitor Out-HDMI Assigns the MONITOR OUT when the HDMI input port is selected. Off / RGB1 / RGB2

This function is not displayed for PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K. Monitor Out-Component Assigns the MONITOR OUT when the COMPONENT input port is selected.

Off / RGB1 / RGB2 This function is not displayed for PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K.

Monitor Out-S-Video Assigns the MONITOR OUT when the S-VIDEO input port is selected. Off / RGB1 / RGB2

This function is not displayed for PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K.


37

Monitor Out-Video Assigns the MONITOR OUT when the VIDEO input port is selected.


Monitor Out-MIU Assigns the MONITOR OUT when the MIU input port is selected. Off / RGB1 / RGB2

This function is not displayed for PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K. Monitor Out Standby Assigns the MONITOR OUT in the standby mode.


Reset Initialize the selected function. X62w / X64w

Keystone V PL90X / PL95X / X90 / X90K / X90w / X95 / X95K / X95i / X95iK

Keystone V / Keystone H [Execute]: After the confirmation message, the selected function will be initialized.

[AUDIO] Tab This tab is displayed for PL90X / PL95X / X90 / X90K / X90w / X95 / X95K / X95i / X95iK.



Treble Adjusts the treble level. [-]: Decrease the treble value. [+]: Increase the treble value.

Bass Adjusts the bass level. [-]: Decrease the bass value. [+]: Increase the bass value.

SRS WOW Switches the mode for SRS WOW mode. Off / Mid / High


Audio - RGB1 Assigns the audio port when the RGB IN1 input port is selected. Off / Audio1 / Audio2 / Audio3 / Audio4

Audio - RGB2 Assigns the audio port when the RGB IN2 input port is selected. Off / Audio1 / Audio2 / Audio3 / Audio4

Audio - M1-D Assigns the audio port when the M1-D input port is selected. Off / Audio1 / Audio2 / Audio3 / Audio4

This function is not displayed for PL95X / X95 / X95K / X95i / X95iK. Audio - HDMI Assigns the audio port when the HDMI input port is selected.

Off / Audio1 / Audio2 / Audio3 / Audio4 / Audio HDMI This function is not displayed for PL90X / X90 / X90K / X90w.

Audio - Video Assigns the audio port when the VIDEO input port is selected. Off / Audio1 / Audio2 / Audio3 / Audio4

Audio - S-Video Assigns the audio port when the S-VIDEO input port is selected. Off / Audio1 / Audio2 / Audio3 / Audio4

Audio - Component Assigns the audio port when the COMPONENT input port is selected. Off / Audio1 / Audio2 / Audio3 / Audio4

Audio MIU Assigns the audio port when the MIU input port is selected. Off / Audio1 / Audio2 / Audio3 / Audio4 / Audio MIU

This function is not displayed for PL90X / X90 / X90K. Audio Out Standby Assigns the audio port in the standby mode.

Off / Audio1 / Audio2 / Audio3 / Audio4 This function is not displayed for PL90X / PL95X / X90 / X90K / X90w / X95 / X95K.

HDMI Audio Switches the mode for the HDMI audio. 1 / 2

This function is not displayed for PL90X / X90 / X90K / X90w.


38

[SCREEN] Tab




Blank Switches the mode for the blank screen. Blue / White / Black / MyScreen / Original

Start Up Switches the mode for the start-up screen. Original / Off / MyScreen

MyScreen Lock Turns off/on the MyScreen lock function. Off / On


Template Switches the mode for the template screen. Test Pattern / Dot-Line1 / Dot-Line2 / Dot-Line3 / Dot-Line4

This function is not displayed for PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K. Reset Initialize the selected function.

Menu Position V / Menu Position H [Execute]: After the confirmation message, the selected function will be initialized.


39

[OPTION] Tab

Function General Description Auto Search Turns off/on the automatic signal search function.

Off / On Auto Keystone Turns off/on the automatic keystone function.

Off / On Auto On Turns off/on the auto on function.

Off / On Auto Off Adjusts the time to count down to automatically turn the projector off.


My Button-1 Assigns the function for the MY BUTTON-1 button on the included remote control. X62w

RGB1 / RGB2 / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / e-SHOT / Volume+ / Volume-

X64w Computer1 / Computer2 / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / e-SHOT / Volume+ / Volume- / Live Mode / Thumbnail / Slide Show / Directory / Remove Media

PL90X / X90 / X90K RGB1 / RGB2 / M1-D / Video / S-Video / Component / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / Active Iris / e-SHOT / Volume+ / Volume-

X90w RGB1 / RGB2 / M1-D / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / Active Iris / e-SHOT / Volume+ / Volume-

PL95X / X95 / X95K RGB1 / RGB2 / HDMI / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / Active Iris / e-SHOT / Volume+ / Volume- / AV Mute / Live Mode / Thumbnail / Slide Show / Directory / Remove Media

X95i / X95iK RGB1 / RGB2 / HDMI / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / Active Iris / My Image / AV Mute / Template / Live Mode / Thumbnail / Slide Show / Directory / Remove Media / Other

My Button-2 Assigns the function for the MY BUTTON-2 button on the included remote control. X62w

RGB1 / RGB2 / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / e-SHOT / Volume+ / Volume-

X64w Computer1 / Computer2 / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / e-SHOT / Volume+ / Volume- / Live Mode / Thumbnail / Slide Show / Directory / Remove Media

PL90X / X90 / X90K RGB1 / RGB2 / M1-D / Video / S-Video / Component / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / Active Iris / e-SHOT / Volume+ / Volume-

X90w RGB1 / RGB2 / M1-D / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / Active Iris / e-SHOT / Volume+ / Volume-

PL95X / X95 / X95K RGB1 / RGB2 / HDMI / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / Active Iris / e-SHOT / Volume+ / Volume- / AV Mute / Live Mode / Thumbnail / Slide Show / Directory / Remove Media

X95i / X95iK RGB1 / RGB2 / HDMI / Video / S-Video / Component / MIU / Information / Auto Keystone Execute / My Memory / Picture Mode / Filter Reset / Active Iris / My Image / AV Mute / Template / Live Mode / Thumbnail / Slide Show / Directory / Remove Media / Other

My Source Assigns the input port for the MY SOURCE/DOC.CAMERA button on the included remote control. RGB1 / RGB2 / HDMI / Video / S-Video / Component / MIU

This function is not displayed for PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K. C.C. - Display Selects the Closed Caption Display setting.

Off / On / Auto This function is not displayed for PL90X / PL95X / X62w / X90 / X90K / X90w / X95 / X95K.

C.C. - Mode Selects the Closed Caption Mode setting. Captions / Text

This function is not displayed for PL90X / PL95X / X62w / X90 / X90K / X90w / X95 / X95K. C.C. - Channel Selects the Closed Caption Channel setting.

1 / 2 / 3 / 4 This function is not displayed for PL90X / PL95X / X62w / X90 / X90K / X90w / X95 / X95K.


40

Service

Function General Description Auto Adjust Selects the automatic adjustment mode.

PL95X / X64w / X95 / X95K / X95i / X95iK Disable / Fast / Fine

PL90X / X62w / X90 / X90K / X90w Disable / Enable

Remote Receiv. Turns off/on the remote sensor. PL90X / PL95X / X90 / X90K / X90w / X95 / X95K / X95i / X95iK

Front (Off / On) Rear (Off / On) Top (Off / On)

This function is not displayed for X62w / X64w. Remote Freq. - Normal Changes the projector’s remote sensor off/on of the normal frequency.

Disable / Enable Remote Freq. - High Changes the projector’s remote sensor off/on of the high frequency.

Disable / Enable

[OTHER] Tab

Function General Description Power Turns off/on the power.


X62w RGB1 / RGB2 / Video / S-Video / Component / MIU

X64w Computer1 / Computer2 / Video / S-Video / Component / MIU

PL90X / X90 / X90K RGB1 / RGB2 / M1-D / Video / S-Video / Component

X90w RGB1 / RGB2 / M1-D / Video / S-Video / Component / MIU

PL95X / X95 / X95K / X95i / X95iK RGB1 / RGB2 / HDMI / Video / S-Video / Component / MIU

Picture Mode Switches the picture mode. PL90X / X62w / X90 / X90K / X90w

Normal / Cinema / Dynamic / Board(Black) / Board(Green) / White Board / Custom PL95X / X64w / X95 / X95K / X95i / X95iK

Normal / Cinema / Dynamic / Board(Black) / Board(Green) / White Board / Daytime / Custom Custom is displayed only. It cannot be set.

Blank On / Off Turns off/on the blank. Off / On

Mute Turns off/on the mute. Off / On


Magnify Adjusts the magnify setting [-]: Decrease the magnify value. [+]: Increase the magnify value.

e-SHOT Displays the e-SHOT data. Off / Image1 / Image2 / Image3 / Image4

This function is not displayed for X95i / X95iK. My Image Displays the My Image data.

Off / Image1 / Image2 / Image3 / Image4 This function is not displayed for PL90X / PL95X / X62w / X64w / X90 / X90K / X90w / X95 / X95K.


41

■ X30N / X35N / X35NK [STATUS] Tab


On / Standby / Cool down Input Source Displays the current input source.

Computer in1 / Computer in2 / Component / S-Video / Video Error Status Displays the current error status.

Normal / Cover Error / Fan Error / Lamp Error / Temp Error / Air Flow Error / Cold Error / Filter Error / Other Error

Blank On/Off Displays the current blank on/off status. On / Off

Mute Displays the current mute status. On / Off




[PICTURE] Tab




Gamma Switches the gamma mode. #1 Custom / #2 Custom / #3 Custom / #4 Custom / #5 Custom / #6 Custom / #1 Default / #2 Default / #3 Default / #4 Default / #5 Default / #6 Default /

Color Temp Switches the color temperature mode. High / Mid / Low / Hi-Bright-1 / Hi-Bright-2 / Hi-Bright-3 / #1 Custom / #2 Custom / #3 Custom / #4 Custom / #5 Custom / #6 Custom




Active Iris Changes the active iris control mode. Presentation / Theater / Off

My Memory Loads the data from the memory. Load1 / Load2 / Load3 / Load4



Brightness / Contrast / Color / Tint / Sharpness [Execute]: After the confirmation message, the selected function will be initialized.


42

Gamma - Custom -


Off / 9 Steps Gray Scale / 15 Steps Gray Scale / Ramp User Gamma Point 1 Adjusts the user gamma point 1.











Off / 9 Steps Gray Scale / 15 Steps Gray Scale / Ramp Color Temp Gain R Adjusts the red color temperature gain.



Color Temp Gain B Adjusts the blue color temperature gain. [-]: Decrease the blue color temperature gain value. [+]: Increase the blue color temperature gain value. [Reset]: Initialize the blue color temperature gain value.





43

[IMAGE] Tab


Normal / 4:3 / 16:9 / 16:10 / 14:9 Over Scan Adjusts the over-scan ratio.

[-]: Decrease the over scan value. [+]: Increase the over scan value.






[INPUT] Tab


TV / FILM / Off Video NR Switches the noise reduction mode.

High / Mid / Low Color Space Switches the mode for color space.


Component / Scart RGB S-Video Format Switches the mode for video format of the S-VIDEO port.

Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL C-Video Format Switches the mode for video format of the VIDEO port.

Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL Frame Lock - Computer in1 Selects the frame lock function on/off of the COMPUTER IN1 port.

On / Off Frame Lock - Computer in2 Selects the frame lock function on/off of the COMPUTER IN2 port.

On / Off Computer in1 Selects the computer input signal type of the COMPUTER IN1 port.

Auto / Sync On G Off Computer in2 Selects the computer input signal type of the COMPUTER IN2 port.

Auto / Sync On G Off

[SETUP] Tab

Function General Description Auto Keystone [Execute]: Performs the automatic keystone distortion correction. Keystone V Corrects the vertical keystone distortion.


Eco Mode Turns off/on the eco mode. Normal / Eco


Standby Mode Switches the standby mode setting. Normal / Saving

Monitor Out - Computer in1 Assigns the MONITOR OUT when the COMPUTER IN1 input port is selected. Computer in1 / Off


Monitor Out - Component Assigns the MONITOR OUT when the COMPONENT input port is selected. Computer in1 / Computer in2 / Off

Monitor Out - S-Video Assigns the MONITOR OUT when the S-VIDEO input port is selected. Computer in1 / Computer in2 / Off

Monitor Out - Video Assigns the MONITOR OUT when the VIDEO input port is selected. Computer in1 / Computer in2 / Off

Monitor Out - Standby Assigns the MONITOR OUT in the standby mode. Computer in1 / Computer in2 / Off

Reset Initialize the selected function. Keystone V



44

[AUDIO] Tab



Speaker Turns on/off the built-in speaker. On / Off

Audio Source - Computer in1 Assigns the audio port when the COMPUTER IN1 input port is selected. Off / Audio1 / Audio2 / Audio3

Audio Source - Computer in2 Assigns the audio port when the COMPUTER IN2 input port is selected. Off / Audio1 / Audio2 / Audio3

Audio Source - Component Assigns the audio port when the COMPONENT input port is selected. Off / Audio1 / Audio2 / Audio3

Audio Source - S-Video Assigns the audio port when the S-VIDEO input port is selected. Off / Audio1 / Audio2 / Audio3

Audio Source - Video Assigns the audio port when the VIDEO input port is selected. Off / Audio1 / Audio2 / Audio3

Audio Out Standby Assigns the audio port in the standby mode. Off / Audio1 / Audio2 / Audio3

[SCREEN] Tab




Blank Switches the mode for the blank screen. MyScreen / Original / Blue / White / Black

Start Up Switches the mode for the start-up screen. MyScreen / Original / Off

MyScreen Lock Turns on/off the MyScreen lock function. On / Off

Message Turns on/off the message function. On / Off

Template Switches the mode for the template screen. Test Pattern / Dot-Line1 / Dot-Line2 / Dot-Line3 / Dot-Line4

C.C. - Display Selects the Closed Caption Display setting. Auto / On / Off

C.C. – Mode Selects the Closed Caption Mode setting. Captions / Text

C.C. - Channel Selects the Closed Caption Channel setting. 1 / 2 / 3 / 4



[OPTION] Tab

Function General Description Auto Search Turns on/off the automatic signal search function.

On / Off Auto Keystone Turns on/off the automatic keystone function.

On / Off Direct On Turns on/off the direct on function.

On / Off Auto Off Adjusts the time to count down to automatically turn the projector off.


My Button-1 Assigns the function for the MY BUTTON-1 button on the included remote control. Computer in1 / Computer in2 / Component / S-Video / Video / Information / Auto Keystone Execute / My Memory / Active Iris / Picture Mode / Filter Reset / Template / AV Mute / My Image / Messenger / Other

My Button-2 Assigns the function for the MY BUTTON-2 button on the included remote control. Computer in1 / Computer in2 / Component / S-Video / Video / Information / Auto Keystone Execute / My Memory / Active Iris / Picture Mode / Filter Reset / Template / AV Mute / My Image / Messenger / Other

My Source Assigns the input port for the MY SOURCE/DOC.CAMERA button on the included remote control. Computer in1 / Computer in2 / Component / S-Video / Video


45

Service

Function General Description Remote Frequency - Normal Changes the projector’s remote sensor off/on of the normal frequency.

Disable / Enable Remote Frequency - High Changes the projector’s remote sensor off/on of the high frequency.

Disable / Enable

[OTHER] Tab

Function General Description Power Turns on/off the power.

On / Off Input Source Switches the input source.

Computer in1 / Computer in2 / Component / S-Video / Video Picture Mode Switches the picture mode.

Normal / Cinema / Dynamic / Board(Black) / Board(Green) / Whiteboard / Daytime / Custom Custom is displayed only. It cannot be set.

Blank On/Off Turns on/off the blank. On / Off

Mute Turns on/off the mute. On / Off


Template On/Off Turns on/off the template screen. On / Off


My Image Displays the My Image data. Off / Image-1 / Image-2 / Image-3 / Image-4

My Image Delete Deletes the My Image data. Image-1 / Image-2 / Image-3 / Image-4


46

■ CL67N / CL69N / PL92X / WX36 / X31 / X36 / X46 [STATUS] Tab


On / Standby / Cool down Input Source Displays the current input source.

Computer in1 / Computer in2 / LAN / USB TYPE A / USB TYPE B / HDMI / Component / S-Video / Video

Error Status Displays the current error status. Normal / Cover Error / Fan Error / Lamp Error / Temp Error / Air Flow Error / Cold Error / Filter Error / Other Error






[PICTURE] Tab




Gamma Switches the gamma mode. Custom-1 / Custom-2 / Custom-3 / Custom-4 / Custom-5 / Custom-6 / Default-1 / Default-2 / Default-3 / Default-4 / Default-5 / Default-6 /

Color Temp Switches the color temperature mode. High / Mid / Low / Hi-Bright-1 / Hi-Bright-2 / Hi-Bright-3 / Custom-1 / Custom-2 / Custom-3 / Custom-4 / Custom-5 / Custom-6




Active Iris Changes the active Iris control mode. Presentation / Theater / Off

My Memory Loads the data from the memory. Load-1 / Load-2 / Load-3 / Load-4

Saves the current adjustment data into the memory. Save-1 / Save-2 / Save-3 / Save-4




47

Gamma - Custom -

Function General Description Test Pattern Changes the test pattern.

Off / 9 Steps Gray Scale / 15 Steps Gray Scale / Ramp Gamma Point 1 Adjusts the user gamma point 1.


Gamma Point 2 Adjusts the user gamma point 2. [-]: Decrease the user gamma point 2 value. [+]: Increase the user gamma point 2 value. [Reset]: Initialize the user gamma point 2 value.









Off / 9 Steps Gray Scale / 15 Steps Gray Scale / Ramp Color Temp Gain R Adjusts the red color temperature gain.








48

[IMAGE] Tab


CL67N / CL69N / PL92X / X31 / X36 / X46 Normal / 4:3 / 16:9 / 16:10 / 14:9

WX36 Normal / 4:3 / 16:9 / 16:10 / 14:9 / Native

Over Scan Adjusts the over-scan ratio [-]: Decrease the over-scan value. [+]: Increase the over-scan value.






[INPUT] Tab


TV / FILM / Off Video NR Switches the noise reduction mode.



Component / Scart RGB S-Video Format Switches the mode for video format of the S-VIDEO port.

Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL C-Video Format Switches the mode for video format of the VIDEO port.

Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL HDMI Format Switches the video format for an input from the HDMI port.

Auto / Video / Computer HDMI Range Changes the digital range for input from the HDMI port.

Auto / Normal / Enhanced Computer in1 Selects the computer input signal type of the COMPUTER IN1 port.

Auto / Sync On G Off Computer in2 Selects the computer input signal type of the COMPUTER IN2 port.

Auto / Sync On G Off Frame Lock - Computer in1 Selects the frame lock function on/off of the COMPUTER IN1 port.


On / Off Frame Lock - HDMI Selects the frame lock function on/off of the HDMI port.

On / Off


49

[SETUP] Tab

Function General Description Auto Keystone [Execute]: Performs the automatic keystone distortion correction. Keystone V Adjusts the vertical keystone distortion


Auto Eco Mode Turns on/off the auto eco mode. On / Off

Eco Mode Turns off/on the eco mode. Normal / Eco





Monitor Out - LAN Assigns the MONITOR OUT when the LAN input port is selected. Computer in1 / Computer in2 / Off

Monitor Out - USB TYPE A Assigns the MONITOR OUT when the USB TYPE A input port is selected. Computer in1 / Computer in2 / Off

Monitor Out - USB TYPE B Assigns the MONITOR OUT when the USB TYPE B input port is selected. Computer in1 / Computer in2 / Off

Monitor Out - HDMI Assigns the MONITOR OUT when the HDMI input port is selected. Computer in1 / Computer in2 / Off

Monitor Out - Component Assigns the MONITOR OUT when the COMPONENT input port is selected. Computer in1 / Computer in2 / Off






[AUDIO] Tab




Mic Level Switches the input level to match that of the microphone connected to the MIC port. High / Low

Mic Volume Adjusts the volume of the microphone connected to the MIC port. [-]: Decrease the volume of the microphone. [+]: Increase the volume of the mocrophone.

Audio Source - Computer in1 Assigns the audio port when the COMPUTER IN1 input port is selected. Off / Audio in1 / Audio in2 / Audio in3

Audio Source - Computer in2 Assigns the audio port when the COMPUTER IN2 input port is selected. Off / Audio in1 / Audio in2 / Audio in3

Audio Source - LAN Assigns the audio port when the LAN input port is selected. Off / Audio in1 / Audio in2 / Audio in3

Audio Source - USB TYPE A Assigns the audio port when the USB TYPE A input port is selected. Off / Audio in1 / Audio in2 / Audio in3

Audio Source - USB TYPE B Assigns the audio port when the USB TYPE B input port is selected. Off / Audio in1 / Audio in2 / Audio in3

Audio Source - HDMI Assigns the audio port when the HDMI input port is selected. Off / Audio in1 / Audio in2 / Audio in3 / Audio HDMI

Audio Source - Component Assigns the audio port when the COMPONENT input port is selected. Off / Audio in1 / Audio in2 / Audio in3

Audio Source - S-Video Assigns the audio port when the S-VIDEO input port is selected. Off / Audio in1 / Audio in2 / Audio in3

Audio Source - Video Assigns the audio port when the VIDEO input port is selected. Off / Audio in1 / Audio in2 / Audio in3

Audio Source - Standby Assigns the audio port in the standby mode. Off / Audio in1 / Audio in2 / Audio in3



50

[SCREEN] Tab





Start Up Switches the mode for thr start-up screen. MyScreen / Original / Off



Template Switches the mode for the template screen. Test Pattern / Dot-Line1 / Dot-Line2 / Dot-Line3 / Dot-Line4 / Circle 1 / Circle 2 / Map 1 / Map 2

C.C. – Display Selects the Closed Caption Display setting. Auto / On / Off


C.C. – Channel Selects the Closed Caption Channel setting. 1 / 2 / 3 / 4



[OPTION] Tab


On / Off Auto Keystone Turns on/off the automatic keystone function.

On / Off Direct Power On Turns on/off direct power on function.

On / Off Auto Power Off Adjusts the time to count down to automatically turn the projector off.


USB TYPE B Selects the function of USB TYPE B port. Mouse / USB Display

My Button-1 Assigns the function for the MY BUTTON-1 button on the included remote control. Computer in1 / Computer in2 / LAN / USB TYPE A / USB TYPE B / HDMI / Component / S-Video / Video / Slideshow / My Image / Messenger / Information / Auto Keystone / My Memory / Active Iris / Picture Mode / Filter Reset / Template / AV Mute / Resolution / Mic Volume / Eco Mode / Other

My Button-2 Assigns the function for the MY BUTTON-2 button on the included remote control. Computer in1 / Computer in2 / LAN / USB TYPE A / USB TYPE B / HDMI / Component / S-Video / Video / Slideshow / My Image / Messenger / Information / Auto Keystone / My Memory / Active Iris / Picture Mode / Filter Reset / Template / AV Mute / Resolution / Mic Volume / Eco Mode / Other

My Source Assigns the input port for the MY SOURCE/DOC.CAMERA button on the included remote control.. Computer in1 / Computer in2 / LAN / USB TYPE A / USB TYPE B / HDMI / Component / S-Video / Video

Service

Function General Description Remote Freq. - Normal Changes the projector’s remote sensor off/on of the normal frequency.

Disable / Enable Remote Freq. - High Changes the projector’s remote sensor off/on of the high frequency.

Disable / Enable


51

[OTHER] Tab



Computer in1 / Computer in2 / LAN / USB TYPE A / USB TYPE B / HDMI / Component / S-Video / Video

Picture Mode Switches the picture mode. Normal / Cinema / Dynamic / Board(Black) / Board(Green) / Whiteboard / Daytime / Custom

Custom is displayed only. It cannot be set. Blank On/Off Turns on/off the blank.

Off / On Mute Turns on/off the mute.

Off / On Freeze Turns on/off the freeze.

On / Off Magnify Adjusts the magnify setting.


Magnify Position Adjusts the magnify position. [ ]: Decrease the vertical magnify position value. [ ]: Increase the vertical magnify position value. [ ]: Decrease the horizontal magnify position value. [ ]: Increase the horizontal magnify position value.


My Image Displays the My Image data. Image-Off / Image-1 / Image-2 / Image-3 / Image-4


Messenger Displays the Messenger. Message-Off / Temporary / Message-1 / Message-2 / Message-3 / Message-4 / Message-5 / Message-6 / Message-7 / Message-8 / Message-9 / Message-10 / Message-11 / Message-12


52

■ CL86X / PL96X / X56 [STATUS] Tab


On / Standby / Cool down Input Source Displays the current Input source.

Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / Component / S-Video / Video

Error Status Displays the current error status. Normal / Cover Error / Fan Error / Lamp Error / Temp Error / Air Flow Error / Cold Error / Filter Error / Other Error




Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current filter. Stack Mode Displays the stack mode status.

Main / Sub This item is not displayed when stack mode status is off.

Reset Initialize the selected function. Lamp Time / Filter Time


[PICTURE] Tab




Gamma Switches the gamma mode. Default-1 / Default-2 / Default-3 / Default-4 / Default-5 / Default-6 / Custom-1 / Custom-2 / Custom-3 / Custom-4 / Custom-5 / Custom-6






My Memory Saves the current adjustment data into the memory. Save-1 / Save-2 / Save-3 / Save-4

Loads the data from the memory. Load-1 / Load-2 / Load-3 / Load-4




53

Gamma - Custom -


Off / 9 steps Gray scale / 15 steps Gray scale / Ramp Gamma Point 1 Adjusts the user gamma point 1.





Gamma Point 5 Setting the user gamma point 5. [-]: Decrease the user gamma point 5 value. [+]: Increase the user gamma point 5 value. [Reset]: Initialize the user gamma point 5 value.







[-]: Decrease the red color temp gain value. [+]: Increase the red color temp gain value. [Reset]: Initialize the red color temp gain value.

Color Temp Gain G Adjusts the green color temperature gain. [-]: Decrease the green color temp gain value. [+]: Increase the green color temp gain value. [Reset]: Initialize the green color temp gain value.

Color Temp Gain B Adjusts the blue color temperature gain. [-]: Decrease the blue color temp gain value. [+]: Increase the blue color temp gain value. [Reset]: Initialize the blue color temp gain value.

Color Temp Offset R Adjusts the red color temperature offset. [-]: Decrease the red color temp offset value. [+]: Increase the red color temp offset value. [Reset]: Initialize the red color temp offset value.

Color Temp Offset G Adjusts the green color temperature offset. [-]: Decrease the green color temp offset value. [+]: Increase the green color temp offset value. [Reset]: Initialize the green color temp offset value.

Color Temp Offset B Adjusts the blue color temperature offset. [-]: Decrease the blue color temp offset value. [+]: Increase the blue color temp offset value. [Reset]: Initialize the blue color temp offset value.


54

[IMAGE] Tab









[INPUT] Tab


TV / Film / Off Video NR Switches the noise reduction mode.



Component / Scart RGB Video Format - S-Video Switches the mode for video format of the S-VIDEO port.

Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL Video Format - Video Switches the mode for video format of the VIDEO port.


Auto / Video / Computer HDMI Range Changes the digital range for an input from the HDMI port.

Auto / Normal / Enhanced Computer in - Computer in1 Selects the computer input signal type of the COMPUTER IN1 port.

Auto / Sync On G Off Computer in - Computer in2 Selects the computer input signal type of the COMPUTER IN2 port.




On / Off


55

[SETUP] Tab



Keystone H Corrects the horizontal keystone distortion. [-]: Decrease the horizontal keystone value. [+]: Increase the horizontal keystone value.

Perfect Fit [Settings...]: Displays the Perfect Fit dialog. Auto Eco Mode Turns on/off the auto eco mode.

On / Off Eco Mode Turns off/on the eco mode.

Normal / Eco Mirror Switches the mode for mirror status.

Normal / H:Invert / V:Invert / H&V:Invert Standby Mode Switches the standby mode setting.

Normal / Saving Monitor Out - Computer in1 Assigns the MONITOR OUT when the COMPUTER IN1 input port is selected.

Computer in1 / Off Monitor Out - Computer in2 Assigns the MONITOR OUT when the COMPUTER IN2 input port is selected.

Computer in2 / Off Monitor Out - LAN Assigns the MONITOR OUT when the LAN input port is selected.

Computer in1 / Computer in2 / Off Monitor Out - USB type A Assigns the MONITOR OUT when the USB TYPE A input port is selected.

Computer in1 / Computer in2 / Off Monitor Out - USB type B Assigns the MONITOR OUT when the USB TYPE B input port is selected.

Computer in1 / Computer in2 / Off Monitor Out - HDMI Assigns the MONITOR OUT when the HDMI input port is selected.

Computer in1 / Computer in2 / Off Monitor Out - Component Assigns the MONITOR OUT when the COMPONENT input port is selected.

Computer in1 / Computer in2 / Off Monitor Out - S-Video Assigns the MONITOR OUT when the S-VIDEO input port is selected.

Computer in1 / Computer in2 / Off Monitor Out - Video Assigns the MONITOR OUT when the VIDEO input port is selected.

Computer in1 / Computer in2 / Off Monitor Out - Standby Assigns the MONITOR OUT in the standby mode.

Computer in1 / Computer in2 / Off Reset Initialize the selected function.

Keystone V / Keystone H [Execute]: After the confirmation message, the selected function will be initialized.


56

Perfect Fit

Function General Description Perfect Fit Selects the perfect fit enable setting.

Enable / Disable Corner Position Left Top V Adjusts the shape of the projected image in left top corner.

[-]: Decrease the vertical value. [+]: Increase the vertical value.

Left Top H Adjusts the shape of the projected image in left top corner. [-]: Decrease the horizontal value. [+]: Increase the horizontal value.

Left Bottom V Adjusts the shape of the projected image in left bottom corner. [-]: Decrease the vertical value. [+]: Increase the vertical value.

Left Bottom H Adjusts the shape of the projected image in left bottom corner. [-]: Decrease the horizontal value. [+]: Increase the horizontal value.

Right Top V Adjusts the shape of the projected image in right top corner. [-]: Decrease the vertical value. [+]: Increase the vertical value.

Right Top H Adjusts the shape of the projected image in right top corner. [-]: Decrease the horizontal value. [+]: Increase the horizontal value.

Right Bottom V Adjusts the shape of the projected image in right bottom corner. [-]: Decrease the vertical value. [+]: Increase the vertical value.

Right Bottom H Adjusts the shape of the projected image in right bottom corner. [-]: Decrease the horizontal value. [+]: Increase the horizontal value.

Line Distortion Left Distortion Adjusts the shape of the projected image in left side distortion.

[-]: Decrease the left side distortion value. [+]: Increase the left side distortion value.

Right Distortion Adjusts the shape of the projected image in right side distortion. [-]: Decrease the right side distortion value. [+]: Increase the right side distortion value.

Distortion Position V Adjusts the vertical distortion position. [-]: Decrease the vertical distortion position value. [+]: Increase the vertical distortion position value.

Top Distortion Adjusts the shape of the projected image in top side distortion. [-]: Decrease the top side distortion value. [+]: Increase the top side distortion value.

Bottom Distortion Adjusts the shape of the projected image in bottom side distortion. [-]: Decrease the bottom side distortion value. [+]: Increase the bottom side distortion value.

Distortion Position H Adjusts the horizontal distortion position. [-]: Decrease the horizontal distortion position value. [+]: Increase the horizontal distortion position value.

Reset After the confirmation message, the Perfect Fit function will be initialized.


57

[AUDIO] Tab





Mic Volume Adjusts the volume of the microphone connected to the MIC port. [-]: Decrease the volume of the microphone. [+]: Increase the volume of the microphone.

Audio Source - Computer in1 Assigns the audio port when the COMPUTER IN1 input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - Computer in2 Assigns the audio port when the COMPUTER IN2 input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - LAN Assigns the audio port when the LAN input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - USB type A Assigns the audio port when the USB TYPE A input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - USB type B Assigns the audio port when the USB TYPE B input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - HDMI Assigns the audio port when the HDMI input port is selected. Audio HDMI / Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - Component Assigns the audio port when the COMPONENT input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - S-Video Assigns the audio port when the S-VIDEO input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - Video Assigns the audio port when the VIDEO input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - Standby Assigns the audio port in the standby mode. Audio in1 / Audio in2 / Audio in3 / Off


[SCREEN] Tab


English / French / German / Spanish / Italian / Norwegian / Dutch / Portuguese / Japanese / Simplified Chinese / Traditional Chinese / Korean / Swedish / Russian / Finnish / Polish / Turkish






Template Switches the mode for the template screen. Test Pattern / Dot-Line1 / Dot-Line2 / Dot-Line3 / Dot-Line4 / Circle 1 / Circle 2 / Map 1 / Map 2 / Stack

C.C. – Display Selects the Closed Caption Display setting. Auto / On / Off






58

[OPTION] Tab


On / Off Auto Keystone Turns on/Off the automatic keystone function.

On / Off Direct Power On Turns on/off the Direct Power On function.


[-]: Decrease the Auto Power off time. [+]: Increase the Auto Power off time.

USB type B Selects the function of USB TYPE B port. Mouse / USB Display

My Button-1 Assigns the function for the MY BUTTON-1 button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / Component / S-Video / Video / Slideshow / My Image / Messenger / Information / Auto Keystone / My Memory / Active Iris / Picture Mode / Filter Reset / Template / AV Mute / Resolution / Mic Volume / Eco Mode / Other

My Button-2 Assigns the function for the MY BUTTON-2 button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / Component / S-Video / Video / Slideshow / My Image / Messenger / Information / Auto Keystone / My Memory / Active Iris / Picture Mode / Filter Reset / Template / AV Mute / Resolution / Mic Volume / Eco Mode / Other

My Source Assigns the input port for the MY SOURCE/DOC.CAMERA button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / Component / S-Video / Video

Service

Function General Description Remote Freq. - Normal Changes the projector’s remote sensor on/off of the normal frequency.

Enable / Disable Remote Freq. - High Changes the projector’s remote sensor on/off of the high frequency.

Enable / Disable

[OTHER] Tab



Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / Component / S-Video / Video

Picture Mode Switches the picture mode. Normal / Cinema / Dynamic / Board(Black) / Board(Green) / Whiteboard / Daytime / Custom

Custom is displayed only. It cannot be set. Blank On/Off Turns on/off the blank.

On / Off Mute Turns on/off the mute.

On / Off Freeze Turns off/on the freeze.

Normal / Freeze Magnify Adjusts the magnify setting.



Template Turns on/off the template screen. On / Off





59

■ CL33X / CL35X / X21i / X26i [STATUS] Tab



Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video Error Status Displays the current error status.







[PICTURE] Tab




Gamma Switches the gamma mode. Default-1 / Default-2 / Default-3 / Default-4 / Default-5 / Default-6 / Custom-1 / Custom-2 / Custom-3 / Custom-4 / Custom-5 / Custom-6





My Memory Saves the current adjustment data into the memory. Save-1 / Save-2 / Save-3 / Save-4





60

Gamma - Custom -


Off / 9 steps Gray scale / 15 steps Gray scale / Ramp Gamma Point 1 Adjusts the user gamma point 1.













Color Temp Gain G Adjusts the green color temperature gain. [-]: Decrease the green temperature temp gain value. [+]: Increase the green color temperature gain value. [Reset]: Initialize the green color temperature gain value.






61

[IMAGE] Tab









[INPUT] Tab




Auto / RGB / SMPTE240 / REC709 / REC601 Video Format - S-Video Switches the mode for video format of the S-VIDEO port.









On / Off


62

[SETUP] Tab




Eco Mode Switches the eco mode. Normal / Eco / Intelligent Eco

Installation Switches the mode for installation status. Front/Desktop / Rear/Desktop / Rear/Ceiling / Front/Ceiling





Monitor Out - USB type A Assigns the MONITOR OUT when the USB TYPE A input port is selected. Computer in1 / Computer in2 / Off

Monitor Out - USB type B Assigns the MONITOR OUT when the USB TYPE B input port is selected. Computer in1 / Computer in2 / Off







[AUDIO] Tab




Audio Source - Computer in1 Assigns the audio port when the COMPUTER IN1 input port is selected. Audio in1 / Audio in2 / Off

Audio Source - Computer in2 Assigns the audio port when the COMPUTER IN2 input port is selected. Audio in1 / Audio in2 / Off

Audio Source - LAN Assigns the audio port when the LAN input port is selected. LAN / Audio in1 / Audio in2 / Off

Audio Source - USB type A Assigns the audio port when the USB TYPE A input port is selected. Audio in1 / Audio in2 / Off

Audio Source - USB type B Assigns the audio port when the USB TYPE B input port is selected. USB type B / Audio in1 / Audio in2 / Off

Audio Source - HDMI Assigns the audio port when the HDMI input port is selected. Audio HDMI / Audio in1 / Audio in2 / Off

Audio Source - S-Video Assigns the audio port when the S-VIDEO input port is selected. Audio in1 / Audio in2 / Off

Audio Source - Video Assigns the audio port when the VIDEO input port is selected. Audio in1 / Audio in2 / Off

Audio Source - Standby Assigns the audio port in the standby mode. Audio in1 / Audio in2 / Off



63

[SCREEN] Tab


English / French / German / Spanish / Italian / Norwegian / Dutch / Portuguese / Japanese / Simplified Chinese / Traditional Chinese / Korean / Swedish / Russian / Finnish / Polish / Turkish












[OPTION] Tab







My Button-1 Assigns the function for the MY BUTTON-1 button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video / Slideshow / My Image / Messenger / Information / Auto Keystone / My Memory / Picture Mode / Filter Reset / Template / AV Mute / Resolution / Eco Mode / Other

My Button-2 Assigns the function for the MY BUTTON-2 button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video / Slideshow / My Image / Messenger / Information / Auto Keystone / My Memory / Picture Mode / Filter Reset / Template / AV Mute / Resolution / Eco Mode / Other

My Button-Eco Assigns the function for the MY BUTTON-Eco button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video / Slideshow / My Image / Messenger / Information / Auto Keystone / My Memory / Picture Mode / Filter Reset / Template / AV Mute / Resolution / Eco Mode / Blank / Freeze / Volume / Auto

My Source Assigns the input port for the MY SOURCE/DOC.CAMERA button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video


64

[OTHER] Tab



Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video Picture Mode Switches the picture mode.

Normal / Cinema / Dynamic / Board(Black) / Board(Green) / Whiteboard / Daytime / Custom Custom is displayed only. It cannot be set.






Template Turns on/off the template screen. On / Off





65

■ CL72X / CL73W / CL73X / NE7 / PL93X / WX36i / X31i / X36i / X46i

[STATUS] Tab



Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video Error Status Displays the current error status.







[PICTURE] Tab




Gamma Switches the gamma mode. Default-1 / Default-2 / Default-3 / Default-4 / Default-5 / Default-6 / Default-7 / Custom-1 / Custom-2 / Custom-3 / Custom-4 / Custom-5 / Custom-6 / Custom-7

Color Temp Switches the color temperature mode. High / Mid / Low / Hi-Bright-1 / Hi-Bright-2 / Hi-Bright-3 / Hi-Bright-4 / Custom-1 / Custom-2 / Custom-3 / Custom-4 / Custom-5 / Custom-6 / Custom-7





My Memory Saves the current adjustment data. Save-1 / Save-2 / Save-3 / Save-4





66

[Custom - Gamma -]


Off / 9 steps Gray scale / 15 steps Gray scale / Ramp User Gamma Point 1 Adjusts the gamma point 1.

[-]: Decrease the gamma point 1 value. [+]: Increase the gamma point 1 value. [Reset]: Initialize the gamma point 1 value.

User Gamma Point 2 Adjusts the gamma point 2. [-]: Decrease the gamma point 2 value. [+]: Increase the gamma point 2 value. [Reset]: Initialize the gamma point 2 value.







[Custom - Color Temp -]


Off / 9 steps Gray scale / 15 steps Gray scale / Ramp Color Temp Gain R Adjusts the color temperature gain R.

[-]: Decrease the color temp gain R value. [+]: Increase the color temp gain R value. [Reset]: Initialize the color temp gain R value.

Color Temp Gain G Adjusts the color temperature gain G. [-]: Decrease the color temp gain G value. [+]: Increase the color temp gain G value. [Reset]: Initialize the color temp gain G value.

Color Temp Gain B Adjusts the color temperature gain B. [-]: Decrease the color temp gain B value. [+]: Increase the color temp gain B value. [Reset]: Initialize the color temp gain B value.

Color Temp Offset R Adjusts the color temperature offset R. [-]: Decrease the color temp offset R value. [+]: Increase the color temp offset R value. [Reset]: Initialize the color temp offset R value.

Color Temp Offset G Adjusts the color temperature offset G. [-]: Decrease the color temp offset G value. [+]: Increase the color temp offset G value. [Reset]: Initialize the color temp offset G value.

Color Temp Offset B Adjusts the color temperature offset B. [-]: Decrease the color temp offset B value. [+]: Increase the color temp offset B value. [Reset]: Initialize the color temp offset B value.


67

[IMAGE] Tab


CL72X / CL73X / NE7 / PL93X / X31i / X36i / X46i Normal / 4:3 / 16:9 / 16:10 / 14:9

CL73W / WX36i Normal / 4:3 / 16:9 / 16:10 / 14:9 / Native

Over Scan Adjusts the over-scan ratio. [-]: Decrease the over scan value. [+]: Increase the over scan value.






[INPUT] Tab




Auto / RGB / SMPTE240 / REC709 / REC601 Video Format - S-Video Switches the mode for video format of the S-VIDEO port.









On / Off


68

[SETUP] Tab




Eco Mode Turns off/on the eco mode. Normal / Eco / Intelligent Eco / Saver

Installation Switches the mode for mirror status. Front/Desktop / Rear/Desktop / Rear/Ceiling / Front/Ceiling





Monitor Out - USB type A Assigns the MONITOR OUT when the USB TYPE A input port is selected. Computer in1 / Computer in2 / Off

Monitor Out - USB type B Assigns the MONITOR OUT when the USB TYPE B input port is selected. Computer in1 / Computer in2 / Off







[AUDIO] Tab

Function General Description Volume Adjusts the Volume.

[-]: Decrease the volume. [+]: Increase the volume.


Audio Source - Computer in1

Assigns the AUDIO SOURCE when the COMPUTER IN1 input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - Computer in2

Assigns the AUDIO SOURCE when the COMPUTER IN2 input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - LAN Assigns the AUDIO SOURCE when the LAN input port is selected. LAN / Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - USB type A Assigns the AUDIO SOURCE when the USB TYPE A input port is selected. USB type A / Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - USB type B Assigns the AUDIO SOURCE when the USB TYPE B input port is selected. USB type B / Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - HDMI Assigns the AUDIO SOURCE when the HDMI input port is selected. HDMI / Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - S-Video Assigns the AUDIO SOURCE when the S-VIDEO input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - Video Assigns the AUDIO SOURCE when the VIDEO input port is selected. Audio in1 / Audio in2 / Audio in3 / Off

Audio Source - Standby Assigns the AUDIO SOURCE in the standby mode. Audio in1 / Audio in2 / Audio in3 / Off


Mic Volume Adjusts the volume of the microphone connected to the MIC port. [-]: Decrease the volume of the microphone. [+]: Increase the volume of the microphone.


69

[SCREEN] Tab

Function General Description Language Switches the OSD language.

English / French / German / Spanish / Italian / Norwegian / Dutch / Portuguese / Japanese / Simplified Chinese / Traditional Chinese / Korean / Swedish / Russian / Finnish / Polish / Turkish / Danish / Czech / Hungarian / Romanian / Slovenian / Croatian / Greek / Lithuanian / Estonian / Latvian / Thai / Arabian / Persian / Portuguese -Brazil

Menu Position Adjusts the menu position. [ ]: Increase the vertical menu position. [ ]: Decrease the vertical menu position. [ ]: Decrease the horizontal menu position. [ ]: Increase the horizontal menu position.











[OPTION] Tab





[-]: Decrease the Auto Power off time. [+]: Increase the Auto Power off time.


My Button-1 Assigns the function for the MY BUTTON-1 button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video / Slideshow / My Image / Messenger / Information / Auto Keystone / My Memory / Active Iris / Picture Mode / Filter Reset / Template / AV Mute / Resolution / Mic Volume / Eco Mode / Saver Mode / Other

My Button-2 Assigns the function for the MY BUTTON-2 button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video / Slideshow / My Image / Messenger / Information / Auto Keystone / My Memory / Active Iris / Picture Mode / Filter Reset / Template / AV Mute / Resolution / Mic Volume / Eco Mode / Saver Mode / Other

My Source Assigns the input port for the MY SOURCE/DOC.CAMERA button on the included remote control. Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video

[Service]

Function General Description Remote Freq. - Normal Changes the projector’s remote sensor on/off of the normal frequency.

Enable / Disable Remote Freq. - High Changes the projector’s remote sensor on/off of the high frequency.

Enable / Disable


70

[OTHER] Tab



Computer in1 / Computer in2 / LAN / USB type A / USB type B / HDMI / S-Video / Video Picture Mode Switches the picture mode.

Normal / Cinema / Dynamic / Board(Black) / Board(Green) / Whiteboard / Daytime / Photo / Custom Custom is displayed only. It cannot be set.





Magnify Position Adjusts the magnify position. [ ]: Decrease the vertical magnify position. [ ]: Increase the vertical magnify position. [ ]: Decrease the horizontal magnify position. [ ]: Increase the horizontal magnify position.


My Image Displays the My Image data. Off / Image-1 / Image-2 / Image-3 / Image-4


Messenger Displays the Messenger. Off / Temporary / Message-1 / Message-2 / Message-3 / Message-4 / Message-5 / Message-6 / Message-7 / Message-8 / Message-9 / Message-10 / Message-11 / Message-12


71

3.15 Turn on the power Select [Control] [Power ON] to turn on the power. You can also turn on the power by clicking the power on icon on the toolbar. If you select a group of projectors, all projectors in the group are powered on.

3.16 Turn off the power Select [Control] [Power OFF] to turn off the power. You can also turn off the power by clicking the power off icon on the toolbar. If you select a group of projectors, all projectors in the group are powered off.

3.17 Display My Image (e-SHOT) You can display My Image (e-SHOT) on projectors that supports My Image (e-SHOT) feature. The My Image (e-SHOT) is available for the following models, CL33X, CL35X, CL67N, CL69N, CL72X, CL73X, CL86X, NE7, PL90X, PL92X, PL93X, PL95X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X62w, X64w, X90, X90K, X90w, X95, X95K, X95i and X95iK. Select [Control] [Display Image] and the image number, when you display My Image (e-SHOT). Select [Control] [Display Image] [Off], when you exit My Image (e-SHOT). If you choose projector group, My Image (e-SHOT) command is sent to the all projectors in the group.

3.18 Change Filter Message You can configure the interval of Filter Message (cleaning reminder interval) from the menu. Select [Control] [Filter Message] to display the configuration dialog window.

Select the desired interval period and press [OK]. If you are selecting a group in the tree view, all of projectors setting under the selected group will be changed. Please note that the change may not affect if the projector models are mixed in the group. In other words, the projector is not supported the selected interval, it will be ignored.


72

3.19 Schedule Events In order to schedule events, select [Schedule] [Edit] from the menu. The Edit Schedule dialogue will appear.

Group selected

Projector selected

Group Information Group Name --- Displays the group name. Contains --- Displays the number of projectors and groups in the group. Comment --- Displays the comment. Projector Information Projector Name --- Displays the projector name. Model --- Displays the model name. Comment --- Displays the comment. Schedule List --- Show the list of scheduled events. [Add] --- Add a new event. [Delete] --- Delete a selected event. [Close] --- Close the dialogue. The Add Schedule dialogue will appear when you are adding a new event.

Schedule Kind --- Select a following schedule type.

Daily / Sunday / Monday / Tuesday / Wednesday / Thursday / Friday / Saturday / Specific date

Date --- Specify the event date for Specific date schedule type. Time --- Specify the event time. Control --- Specify the event. [OK] --- Add the event and close the dialogue.


73

3.20 Activate monitoring scheduled events Select [Schedule] [Start]. You can also activate monitoring events by clicking the schedule start icon on the toolbar. You cannot add, delete or edit an event during while the event monitoring process is active. Please see the chapter 5 for the details.

3.21 Stop monitoring scheduled events Select [Schedule] [Stop]. You can also stop the monitoring events by clicking [schedule stop] icon on the toolbar. Please see the chapter 5 for the details.

3.22 Polling Interval Period Select [Option] [Status Check Interval], enter the polling interval time in seconds. The polling interval time must be within the range from 10 to 3600 seconds.


74

3.23 Mail Setting A notification mail will be sent when any error or selected condition occurs. Select [Option] [Mail Settings] to open the mail settings dialogue.

(1) Mail Settings Mail Settings dialog is as follows. Send Mail --- Enable / Disable send mail function. SMTP Server --- Enter the SMTP Server. From Address --- Enter the sender’s mail address. Send Address --- Enter the receiver’s mail addresses up to 10 addresses. [Add]: Add a receiver’s mail address. [Delete]: Delete a receiver’s mail address. [Edit]: Edit receiver’s mail address. Subject --- Enter the subject. Mail Text --- Mail Text Setting screen appears to set the mail message. Attach File --- Enter the file name of attached file (optional). [Browse]

: File dialogue appears.

Mail Send Test --- Send a test mail.

(2) Mail Address Settings Mail Address Setting dialogue is as follows. Mail Address --- Enter the mail address to be sent, up to

256 characters. [TO][CC][BCC]: Select TO / CC / BCC. Notification --- Chose the Error / Alarm to send the mail. [Select All]: Turn all the check box ON. [Release All]: Turn all the check box OFF.


75

(3) Mail Text Settings Mail Text Settings dialogue is as follows.

Cover Error --- Enter the text message, which is sent when Cover Error occurs. Fan Error --- Enter the text message, which is sent when Fan Error occurs. Lamp Error --- Enter the text message, which is sent when Lamp Error occurs. Temp Error --- Enter the text message, which is sent when Temp Error occurs. Air Flow Error --- Enter the text message, which is sent when Air Flow Error occurs. Lamp Time Error --- Enter the text message, which is sent when Lamp Time Error occurs. Cold Error --- Enter the text message, which is sent when Cold Error occurs. Filter Error --- Enter the text message, which is sent when Filter Error occurs. Other Error --- Enter the text message, which is sent when Other Error occurs. Disconnect --- Enter the text message, which is sent when connection is disconnected. Lamp Time Alarm --- Enter the text message, which is sent when Lamp Alarm Time comes. Filter Time Alarm --- Enter the text message, which is sent when Filter Alarm Time comes.


76

3.24 MY IMAGE (e-SHOT) transfer You can send a My Image (e-SHOT) file to a projector that supports My Image (e-SHOT) feature. This function is available for the following models, CL33X, CL35X, CL67N, CL69N, CL72X, CL73W, CL73X, CL86X, NE7, PL90X, PL92X, PL93X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X90 and X90K. The PL95X, X62w, X64w, X90w, X95, X95K, X95i and X95iK support My Image (e-SHOT) also, but this tool is not supported those models due to transfer mechanism difference. Please refer to the Projector Transfer Application which supports this feature for these models. Select [Option] [Image Send] to display the window “Send Image file to projector(s)” as shown next. In order to add projectors on the list, please mark the projector group on the tree view. Also you can unselect projector individually. Once you select the image file and store location number, the “Send” button becomes available. The compatible image file is only PJ1 format file that can be created by Projector Image Tool (PJImg).And then, click the Send button to transfer image. The maximum size of transferred file is depending on the model. Please check the following list. PJ1 format file

CL33X / CL35X / CL67N / CL69N / CL72X / CL73W / CL73X / CL86X / NE7 / PL90X / PL92X / PL93X / WX36 / WX36i / X21i / X26i / X30N / X31 / X31i / X35N / X35NK / X36 / X36i / X46 / X46i / X56 / X90 / X90K

Less than equal 130,816byte JPEG file

CL33X / CL35X / CL67N / CL69N / CL72X / CL73W / CL73X / CL86X / NE7 / PL92X / PL93X / WX36 / WX36i / X21i / X26i / X31 / X31i / X36 / X36i / X46 / X46i / X56

Less than equal 262,144byte The status is shown during transfer. The status will change “Completed” if it succeeds.

[Note]

Please verify the port setting on the projector and the port / authentication setting on the application.


77

3.25 User-defined Model

3.25.1 Add an User-defined Model

You can create your own projector definition and add it as User-defined model. In order to add new User-defined model, click [Add Model…] button on the Add Projector window. Once you have added a User-defined model, the new model is added in the standard model list.

(1) General Settings

Model Name --- Enter the name of User-defined model. Command Type --- Select command type wither Binary or Text (ASCII). Power On Command --- Define Power On command. Up to 32 ASCII character length.

Binary type command Ex: BEEF030600BAD2010000600100 * Only 0-9, a-f and A-F are available to enter.

Text type command Ex: POWER ON[CR] * Control characters are defined as below.

Power Off Command --- Define Power Off command. Up to 32 ASCII character length. Binary type command

Ex: BEEF0306002AD3010000600000 * Only 0-9, a-f and A-F are available to enter.

Text type command Ex: POWER OFF[CR] * Control characters are defined as below.

Control Characters

Control Character Notation Control Character Notation Control Character Notation NUL 0x00 [NUL] VT 0x0b [VT] SYN 0x16 [SYN] SOH 0x01 [SOH] NP 0x0c [NP] ETB 0x17 [ETB] STX 0x02 [STX] CR 0x0d [CR] CAN 0x18 [CAN] ETX 0x03 [ETX] SO 0x0e [SO] EM 0x19 [EM] EOT 0x04 [EOT] SI 0x0f [SI] SUB 0x1a [SUB] ENQ 0x05 [ENQ] DLE 0x10 [DLE] ESC 0x1b [ESC] ACK 0x06 [ACK] DC1 0x11 [DC1] FS 0x1c [FS] BEL 0x07 [BEL] DC2 0x12 [DC2] GS 0x1d [GS] BS 0x08 [BS] DC3 0x13 [DC3] RS 0x1e [RS] HT 0x09 [HT] DC4 0x14 [DC4] US 0x1f [US] LF 0x0a [LF] NAK 0x15 [NAK] DEL 0x7f [DEL]


78

(2) Communication Settings

RS-232C --- COM port parameter setting (if RS232C uses) bits/s --- Baud rate Data bits --- Data bit Parity --- Parity bit Stop bit --- Stop bit Flow Control --- Flow control Network --- Select network protocol (TCP or UDP)

(3) Command Definitions 1

Name --- Enter the name of command, up to 32 ASCII characters. Command --- Define the command up to 32 ASCII characters.

The allowed characters are depending on the command type selection (binary or Text) on the General Setting TAB.


79

(4) Command Definitions 2

Name --- Enter the name of command, up to 32 ASCII characters. Command --- Define the command up to 32 ASCII characters. The allowed characters are depending

on the command type selection (binary or Text) on the General Setting TAB.

3.25.2 Edit User-defined Model

In order to edit User-defined model, select [Option] [Edit User-defined Model]. The following window will appear.

(1) Edit Choose a User-defined Model form the list, and then click [Edit…] button.

(2) Delete Choose a User-defined model from the list, and then click [Delete…] button. The confirmation message will be appeared. The deleted model on the projector tree will be removed when the User-defined Model definition is deleted.


80

3.25.3 Control User-defined Model

(1) Power On Select [Control] [Power ON] to turn on the power. You can also turn on the power by clicking the power on icon on the toolbar. If you select a group of projectors, all projectors in the group are powered on.

(2) Power Off Select [Control] [Power OFF] to turn off the power. You can also turn off the power by clicking the power off icon on the toolbar. If you select a group of projectors, all projectors in the group are powered off.

(3) Command No.1-10 Select [Control] [Execute Command] to execute a command.

(4) Schedule Only Power On / Off commands are allowed as the schedule event for User-defined model.

3.26 Open the build-in HTML page in the projector You can access the projector built-in HTML page from PJMan directly. Select the projector from the tree view, and then go to [Option] [Open with] from the menu. The default browser on your computer will launch automatically and access the selected projector HTML page. This function supports embedded network projector models only.


81

3.27 Setup PJMessenger to Projector For projectors that support Messenger function, PJMan allows you to setup PJMessenger message from PJMessenger file (pjm file), that is exported from another application software - Projector Messenger Tool (PJMessenger). Select projector(s) from the tree view, then go [Option] [Send Messenger data]. The following dialog will be displayed. It will populate only the projectors that supports PJMessenger function.

Mark the checkbox in the Projector name field to select the projectors that you want to upload the PJMessage file. Send button will be enabled when you choose PJMessenger file and store location number.

Press [Send] button to start the pload process. The status field will be shown as “Completed” when the process is done.

3.28 About Dialogue Select [Help] [About] to open the about dialogue.


82

4 Mail Feature

4.1 Mail Format The Projector Management Application sends an e-mail by following format.

4.2 Others The e-mail sending process is triggered by the transition from normal status to error (or event) mode. When an error happens at the startup, this Projector Management Software application will not send e-mail.

Time : YYYY / MM / DD hh:nn:ss Projector Name : xxxxxx Connection: xxxxxx Message: xxxxxxxxxxxxxxxxxx (Typed in text on Message Setting screen) (Sample 1) Time: 2003 / 11 / 11 23:12:22 Projector Name: Projector1 Connection: 192.168.1.10 (00-00-87-F3-EB-01) Message: Fan Error!!! (Sample 2) Time: 2003/11/12 20:00:17 Projector Name: Projector2 Connection: COM1 Message: Lamp Error!!!


83

5 Status The projector status is classified with colored label. Status Display

Normal

(Black text with white background)

Warning

(Black text on yellow background)

Error

(White text on brown background)

Disconnect

(White text on red background)

All of projectors are normal

(Black text on white background)

At least one projector is in the warning state and rests of projectors are normal.


At least one projector is in the error state and rests of projectors are either warning or normal state.


At least one projector is in the disconnect state, and rest of projectors are error, warning or normal.


Each projector is classified by the colored label on the list of the projector when the user selects a group. Status Display

Normal

(Black text with white background)

Warning


Error


Disconnect


The priority of colored label is; 1st Disconnect, 2nd Error and 3rd Warning.


84

6 Output Log In order to enable logging status data, please enable log setting through [File] [Log]. It does not record log data when it is unchecked.

Output folder : (PJman installed folder)\Log\ Filename :

TCP / IP network --- (IP address)_(Port No.).log (ex: 192.168.1.10_23.log) Serial (RS232C) --- COMM_(Port No.).log (ex: COMM_1.log)

Format : Command log

[Cmd ], [Date], [Action code], [Operation ID], [Operation Name], [Setting Value], [Result], [Return Value]

Status log (only status is changed) [Stat], [Date], [Status Name], [Status]

Example [Stat], 2008/11/07 20:06:16, Power Status, ON [Stat], 2008/11/07 20:06:16, Lamp Time, 0 [Stat], 2008/11/07 20:06:16, Filter Time, 0 [Stat], 2008/11/07 21:06:16, Lamp Time, 1 [Stat], 2008/11/07 21:06:16, Filter Time, 1 [Cmd ], 2008/11/07 21:10:35, Set, 0x2000, Input Source, 1, OK, 0 [Cmd ], 2008/11/07 21:15:27, Get, 0x6000, Power, 0, OK, 0 [Cmd ], 2008/11/07 21:15:27, Set, 0x6000, Power, 0, OK, 0 [Stat], 2008/11/07 21:15:30, Error Status, Disconnect


85

7 Create Log Report In order to create Log Report, choose a projector or group that you want to create Report from the tree view. Ands then, select [File] [Log Report]. The following dialogue appears.

Period --- The reporting period. Start : Start Date End : End Date Output folder --- Output folder The Log Report will create in the output folder when OK button is pressed. The folder contains individual Log Report of each projector separately. The individual log life is provided as csv format with projector name (“projector name.csv”).

The format of Log Report is shown below.

Item Description Note Projector Name Projector name Model Model name Connection Connection type Serial (RS232C):

COM Port number Network: IP Address:Portnumber (MAC address)

Period Log data period yyyy/mm/dd Use Information Usage information Date Date yyyy/mm/dd

Power On Count Sum of power status change from OFF to ON Power Off Count Sum of power status change from ON to OFF Lamp Time Lamp hours The lamp hours when the report is generated. Filter Time Filter hours The filter hours when the report is generated. Error Count Sum of Error / Warnings

Error Information Error Information Date Date of Error yyyy/mm/dd

Time Time of Error hh:nn:ss Error Info Error type

Projector Name: Projector 1 Model: X62w Connection: 192.168.1.10:23 (00-00-87-f3-eb-01) Period: 2008/04/01 - 2008/04/30 Use Information [Date],[Power On Count],[Power Off Count],[Lamp Time],[Filter Time],[Error Count] 2008/04/01,5,5,145,145,0 2008/04/02,3,3,148,148,1 : : 2008/04/30,1,1,193,193,0 Error Information [Date], [Time], [Error Info] 2008/04/02,17:43:36,Disconnect


86

8 Create Status Report You can create the status report as HTML format. The report shows a current snapshot of projector status in a particular group, searched group or groups. In order to show the status report, select the group or projector. And then go to [File] [Output Report] from the menu. The status report will be shown in the web browser.

The status report will be given by group as shown below.


Date post:	12-Oct-2020
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

New 3M Digital Projector · 2012. 8. 24. · 240V AC, 50/60 Hz).The use of other replacement lamps,...

Documents