Ericsson Internal | 2016-08-23 | Page 1 (57)
2016 New DTN Project
New basebandAnd radio system
Ericsson Internal | 2016-08-23 | Page 2 (57)
Safety Equipment
Hand protection
Eye protection
Ear protectionRope Set
and pulleys
Tower Work Set
Full Body Harness with lanyards and
work placement adjusters
Foot protection
Head protection
More detail: See Ericsson HSSE policy
Ericsson Internal | 2016-08-23 | Page 3 (57)
Tools requiredElectrostatic Discharge (ESD)
wrist strap (static control wrist
strap)
Wire stripper 0.2–6.0 mm
Side cutters
Slip joint pliers
Hammer drill with
depth restrictor
Torque screwdriver 0.5-4.0 Nm / 5–25 Nm Torx T10 / T20 / T25 / T30
Spirit level
Torque wrench 5–25 Nm / 20–100 Nm
Socket 10 mm
Socket 13 mm
Socket 16 mm
Socket 22 mm
Torque wrench 5–100 Nm Open-ended head 32 mm
Open-ended head 16 mm
Open-ended head 18 mm
Crosshead screwdriver Flathead screwdriver
Cleaning
equipment
Ericsson Internal | 2016-08-23 | Page 4 (57)
New radio system
Radio Available Weight 2G 3G 4G CPRIWCDMA
CarriersIBW Power TX RX
Cascade
TX850 1800 2100
0208 9 Kg. 2x10 Gbps 8 75 MHz 2 2 Q3 Q2
2203 5 Kg. 2x10 Gbps 4 40 MHz 2x5W 2 2 4x4
2212 18 Kg. 2x 2.5/5/10
Gbps 8 75 MHz 2x80W 2 2 2017 2017 2017
2217 10 Kg. 2x10 Gbps 6 40MHz 2x40W 2 2 4x4
2219 17 Kg. 2x 2.5/5/10
Gbps 8 40MHz
2x60W
2x80W2 2 2017 2017 2017
4407 11 Kg.
2x
2.5/5/9.8
Gbps
65 MHz 4x20W 4 4 -
4415 20 Kg. 2x 2.5/5/10
Gbps 8 75 MHz 4x40W 4 4 - 2017 2017 2017
Ericsson Internal | 2016-08-23 | Page 5 (57)
Macro radio
3xin same volume
Capacity
Smallest footprint
Ericsson Internal | 2016-08-23 | Page 6 (57)
› 2TX/2RX, 4TX/4RX by use of two 2217
› 2x40W, 40 MHz IBW FDD
Up to › 6 carriers WCDMA
Up to › 40 MHz LTE carriers
› 2x10 Gbps CPRI
12 › kg
› -48 VDC
AISG TMA & RET support›
2 › external alarm
Optional fan for increased site flexibility›
IP › 65, -40 to +55 ̊C
Maximum power consumption for B› 1 <300W
RADIO 2217
Radio dimensionsMounting points Optional FAN
291 mm105 mm
340 mm
Ericsson Internal | 2016-08-23 | Page 7 (57)
› GSM, WCDMA & LTE
› 2x60 W
› 40 MHz IBW
› Up to 10 Gbps CPRI
› SFP+ supported
› Carrier capacity
– Up to 8 GSM
– Up to 8 WCDMA
– Up to 2x 20 MHz LTE
› 6 external alarms
› Weight : 22 kg
rrus13
Ericsson Internal | 2016-08-23 | Page 8 (57)
› New modular micro radio system
› Macro feature parity, coordination
› 4 liter and 5 kg installed50%Smaller & lighter
Micro Radio
Ericsson Internal | 2016-08-23 | Page 9 (57)
105 mm
› 2TX/2RX, 4TX/4RX by use of two 2203
› 2x5W
40 › MHz IBW FDD
Up to › 4 carriers WCDMA
Up to › 40 MHz LTE carriers
› 2x10 Gbps CPRI
› 5kg include bracket and cover
AC or › -48 VDC
Integrated or external antenna›
2 › external alarm
IP › 65
› -40 to + 55 ̊C
Maximum power consumption for B› 1 <100W
RADIO 2203
Single band
Dual band
Rail mount 19 inch mount
Ericsson Internal | 2016-08-23 | Page 10 (57)
RADIO CORE
SUPPORT SYSTEM
ANTENNA
200 mm
200 mm
Radio dimensions
Total depth with front cover: 100mm
Total depth with high-band antenna: 119mm
Radio 2203
Ericsson Internal | 2016-08-23 | Page 11 (57)
world’s bestbasebandMade b e t t e r2x
Ericsson Internal | 2016-08-23 | Page 12 (57)
› 19 inch indoor main unit for baseband
› Mix and match
– Baseband 5212
– Baseband 5216
– Baseband R503
– Baseband T503
– DUW, DUG, DUS & TCU
› Provide the optimal capacity & configuration of GSM,
WCDMA or LTE and combinations thereof
› Dimensions : 483 x 355 x 66 (mm)
› Weight 5.0Kg (<10Kg with DUW)
Baseband Main Unit 6601
2x DUS/BB/IRU
Or 1x DUW
EC Bus X,Y,Z
and SAU
Status
LEDs
Input -48V DCOutput -48V DC
2 units
8x Ext
alarms
Ericsson Internal | 2016-08-23 | Page 13 (57)
› LTE (FDD & TDD supported)
– 8000 connected users
– 1.2 Gbps Downlink & 600 Mbps Uplink
– Up to 24 cells & 960 MHz antenna bandwidth
› WCDMA
– 1152 CE Downlink & 1920 CE Uplink
– 336 Mbps Downlink & 168 Mbps Uplink
– Up to 24 cell carriers
› GSM
– Up to 24 TRX in a mixed mode configuration
Baseband 5216
Ericsson Internal | 2016-08-23 | Page 14 (57)
Baseband 5216
RI Port
RRU CPRI Port
GPS Sync Port LMT Port -48 VDC
Input
EC BusRJ-45
TransmissionOptical
Transmission
Inter DU Link
Ericsson Internal | 2016-08-23 | Page 15 (57)
RRUS13
RBS6601
BB 5216
Macro based
Radio 2217 Radio 2203
RBS6601
BB 5216
Macro based
RBS6601
BB 5216
Micro based
Various configurations
Ericsson Internal | 2016-08-23 | Page 16 (57)
IPRAN
Bb 5216 connectionsmixed mode WCDMA+LTE
IDL IPRAN
AUX OIL
RI F DC
GPS
U/L2100
SW 16B support.
U/L2100 2x2 MIMO = Max 6 sectors
4X4 MIMO or 2T4R = 3 sectors
Ericsson Internal | 2016-08-23 | Page 17 (57)
U/L2100 rrus133-6 sectors macro site
New Materials
(3 sectors material list)
1 x MU
2 x BB 5216
3 x RRUS13 + DC Cables
3x OIL 4 Core
2x Patch Cords
U/L2100
Ericsson Internal | 2016-08-23 | Page 18 (57)
U/L2100 radio 22033-6 sectors micro site
New Materials
(3 sectors material list)
1 x MU
2 x BB 5216
3 x Radio 2203 + DC Cables
3x OIL 4 Core
2x Patch Cords
U/L2100
Ericsson Internal | 2016-08-23 | Page 19 (57)
U/L2100 radio 22033-6 sectors micro site
New Materials
(3 sectors material list)
1 x MU
2 x BB 5216
3 x Radio 2203 + DC Cables
3x OIL 4 Core
2x Patch Cords
U/L2100
Integrated Antenna option
Ericsson Internal | 2016-08-23 | Page 20 (57)
L1800 radio 22173-6 sectors macro site
New Materials
(3 sectors material list)
1 x MU
1 x BB 5216
3x Radio 2217 + DC Cables
3x OIL 4 Core
1x Patch Cord
L1800
Ericsson Internal | 2016-08-23 | Page 21 (57)
L1800 radio 22033-6 sectors micro site
New Materials
(3 sectors material list)
1 x MU
1 x BB 5216
3 x Radio 2203 + DC Cables
3x OIL 4 Core
1x Patch Cords
L1800
Ericsson Internal | 2016-08-23 | Page 22 (57)
L1800 radio 22033-6 sectors micro site
New Materials
(3 sectors material list)
1 x MU
1 x BB 5216
3 x Radio 2203 + DC Cables
3x OIL 4 Core
1x Patch Cords
L1800
Integrated Antenna option
Ericsson Internal | 2016-08-23 | Page 23 (57)
RRU13 connections
CPRI
DATA 1
ALD
Antenna Line Device
(RET Connection)
-48 V DC
Input
CPRI
DATA 2
TXA/RXA TXB/RXB
Ground point
Ericsson Internal | 2016-08-23 | Page 24 (57)
Radio 2217 connections
CPRI
DATA 1
ALD
Antenna Line Device
(RET Connection)
-48 V DC
Input
CPRI
DATA 2
TXA/RXA TXB/RXB
Ground point
LED Status
FAN or
External Alarms
Ericsson Internal | 2016-08-23 | Page 25 (57)
Install
System
Tower
ownerNew site Antenna Option 1 Antenna Option 2 Remark
U/L2100DTN or
ShareNew build ADU4518R6v01 A19451811 Based on antenna available in stock
U850 DTN New build A79451700v02 -
U850 Share New build ADU451807v01 -
U/L2100 Share Existing U850Reuse ADU451807v02 - In case existing ADU451807
Swap with ADU451807v02 Swap with ADU4518R12
3g 2100 new siteantenna installation options
Ericsson Internal | 2016-08-23 | Page 26 (57)
DTN 3G 2.1
RRU
Port A
+ Ant
RRU
Port B
- Ant
RRU
Port ARRU
Port B
U/L 2100 overviewAntenna single Band
U/L 2100
AGISSON: A49151811
Ericsson Internal | 2016-08-23 | Page 27 (57)
E1800
Radio 2217 A RRUS13 A
Radio 2217 B RRUS13 B
DTN 3G 2.1Radio 2217
1800
RRUS13
2100
Radio 2217
1800 to
ports ‘L’
RRUS13
2100 to ports
‘R’
RRUS13
Port A
+ Ant
RRUS13
Port B
- Ant
E 1800 + 3G 2100
U/L 2100 + E 1800 overviewAntenna single Band 4-port
AGISSON: ADU451819
Ericsson Internal | 2016-08-23 | Page 28 (57)
Radio 2217 A RRUS13 A
Radio 2217 B RRUS13 B
Example setup Example setup
E 1800 + U/L 2100
U/L 2100 + E 1800 overviewAntenna single Band 4-port
AGISSON: ADU4518R6v01
(Integrated RET )
First installed system uses ‘AISG In’
and controls antenna set ‘a’
Ericsson Internal | 2016-08-23 | Page 29 (57)
TX/RX RX
3G 850
U/L 2100 overviewantenna Dual Band 4 port
RRUS01 A+ RRUS13 A+
RRUS01 B- RRUS13 B-
Filter
850
RF B
-Ant
RF A
Filter
+ Ant
RRUS13
Port A
+ Ant
RRUS13
Port B
- Ant
3G 850 + 3G 2100
AGISSON: ADU451807
3G 850 + E 1800
OR
DTN 3G 2.1
Ericsson Internal | 2016-08-23 | Page 30 (57)
U/L 2100 overviewantenna Dual Band 4 port
RRUS01 A+ RRUS13 A+
RRUS01 B- RRUS13 B-
3G 850 + 3G 2100
AGISSON: ADU4518R12
(Integrated RET )
3G 850 + E1800
OR
TX/RX RX
3G 850 Filter
850
RF B
-Ant
RF A
Filter
+ Ant
RRUS13
Port A
+ Ant
RRUS13
Port B
- Ant
DTN 3G 2.1
Ericsson Internal | 2016-08-23 | Page 31 (57)
Overview – tower
DC power
Jumpers
OIL cable DUW
RET/RCU
DC power
Jumpers
OIL cable
RET/RCU
OIL cable DUSRR
US
RR
US
New Clamps 3x2
New OIL cable to be looped
with existing
3G 3G+4G
Ericsson Internal | 2016-08-23 | Page 32 (57)
SST 35/45m- 3 sectors
DC power
Jumpers
OIL cable
RET/RCU
RR
U
Site breakdown
Rectifier with • aircon door
Installation on frame at tower base•
Tower • 35/45m with 1m ladder spacing
Support up to • 6 antennas (CW check)
• 3x Single antenna mounts
Actual mount to be confirmed after antenna model is •
chosen/CW checks
• 3x RRU behind ant
Rectifier
IPRAN
DU/BB 5216
Single band antennas
Add single mount & RRU/antenna
Ericsson Internal | 2016-08-23 | Page 33 (57)
Radio 2217 mounting scenarios
Rad
io
22
17
Ericsson Internal | 2016-08-23 | Page 34 (57)
Pole 9m –Example - single sector
DC power
Jumpers
OIL cable
RET/RCU
RR
U
Rectifier
IPRAN
DU/BB 5216
Site breakdown
• Centrally located rectifier with aircon door
• Installation on H-Beam
• Horizontal ladder is site specific
• Standard 400mm where possible
• 9m Pole with 1m ladder spacing
• Support up to 6 antennas
• Single or twin antenna mounts
• Depend on configuration, 1/2/3 cells
• Actual mount to be confirmed after antenna model is
chosen/CW checks
• RRU behind antenna
Ericsson Internal | 2016-08-23 | Page 35 (57)
Ra
dio
2203
Ra
dio
2203
E-pole 12m - 3 sectors
DC power
Jumpers
OIL cable
RET/RCU
Site breakdown
Rectifier optional or PBS•
RBS• 6320 installed directly on E-pole
12• m E-Pole with 1m ladder spacing
Support up to • 3 antennas (CW check)
• 2x twin antenna mounts
Actual mount to be confirmed after antenna model is •
chosen/CW checks
• 3x RRU behind antenna or new radio on single 2m pole
R
R
U
R
R
U
R
R
U
3x Rail mounted
Radios 2203
E-Pole Micro cell
Ra
dio
2203
RBS6320 installed with
Baseband and IPRAN
Radio 2203mounting andinstallation
Ericsson Internal | 2016-08-23 | Page 37 (57)
Radio 2203
Ericsson Internal | 2016-08-23 | Page 38 (57)
Rail Mounting options
Ericsson Internal | 2016-08-23 | Page 39 (57)
Rail installation
Fasten the mounting bracket to the
Support by tightening the bolts.
Hook the Support onto the
upper part of the rail.
Push the lower part of the
Support against the lower part
of the rail.
Ericsson Internal | 2016-08-23 | Page 40 (57)
Rail installation
Fit the bolt in the rail groove. Tighten the bolt to fasten the
Support to the rail. Make sure
that the Support is firmly attached
to the rail.
Radio 2217 mounting andinstallation
Ericsson Internal | 2016-08-23 | Page 42 (57)
Rail Mounting optionsSide Wall installation Flat Pole installation
Pole installation with single pole clamp
Flat Wall installation Side Pole installation
Dual pole clamp
Ericsson Internal | 2016-08-23 | Page 43 (57)
Rail descriptionRail Product code
Dimensions
(H×D×L) (mm)
Rail
Weight
Maximum
Radio support
SEF901305/0180 208×45×180 1.42 kg 1
SEF901305/0300208 ×45×300 2.36 kg
3 Radio or
2 Radio/fan
SEF901305/0450 208×45×450 3.54 kg4 Radio or
3 Radio/fan
SEF901305/1100 208×45×1100 8.65 kg
9 Radio or
8 Radio/fan
(Dual Pole mount is
required)
SXK1252540/1 138×187×197 2.4 Pole clamp
Ericsson Internal | 2016-08-23 | Page 44 (57)
Bracket Mounting positions
Position 1Position 2
8mm x 20mm
Hex screws (qty 4)
1. If required remove the plugs in the radio mounting holes. Fit the
retaining bolt loosely to the bottom of the bracket.
2. Orientate the bracket with the retaining bolt on the bottom and
secure to the radio as required using the 4 8mm mounting bolts
supplied.
3. Torque the four bracket bolts to 22 Nm with the 13mm socket on
the torque wrench.
Radio Rail Bracket : SEF901304/1
Radio rail bracket 13mm. bolts
Slot for
lateral
adjust
Retaining Bolt/nut. Leave
loose to engage rail slot.W x H x L : 70 x 35 x 200
Ericsson Internal | 2016-08-23 | Page 45 (57)
Attaching The Radio to railHook the top flange on the radio bracket onto the rail
upper flange and swing down so it is flush on the rail
and the retaining bolt engages into the rail slot. Slide
the radio to adjust spacing with adjacent radios as
required (min 7mm no fan or no space with fan.
Tighten the retaining bolt with a deep
13mm socket to allow the nut to sit in the
slot on the radio bracket. Torque the radio
bracket bolt to 22 Nm.
Ericsson Internal | 2016-08-23 | Page 46 (57)
Install Rail on Wall
1. Mark the positions of the mounting
holes using the footprint of the rail as
a drill template.
2. Drill mounting holes in the wall.
Ericsson Internal | 2016-08-23 | Page 47 (57)
Install Rail on Wall
3. Insert plugs or an expander bolt into the
hole. (Plugs or expander bolts are not
delivered with the unit)
4. Position the rail over the holes and
fasten with screws using the appropriate
torque. Make sure that the bolts are
securely fastened.
Ericsson Internal | 2016-08-23 | Page 48 (57)
Mounting on tower/ polesingle bracket
Ericsson Internal | 2016-08-23 | Page 49 (57)
Single Pole Clamp Installation
1. Assemble the pole clamp 2. Install the rail on the pole clamp. 3. Tighten the nuts.
Ericsson Internal | 2016-08-23 | Page 50 (57)
Single Pole Clamp Installation
4. Install the pole clamp on the pole 5. Tighten the nut on pole clamp
Ericsson Internal | 2016-08-23 | Page 51 (57)
Single Pole Clamp Installation
1
2
Ericsson Internal | 2016-08-23 | Page 52 (57)
Single Pole Clamp Installation
3 4
Ericsson Internal | 2016-08-23 | Page 53 (57)
Install Radio SFP Modules
1. Remove the protective cap from the optical
cable 1 connector on the Remote Radio Unit.
2. Important: Verify with material or site records
that the SFP is the correct type and part
number. Contact support for help if required.
3. Insert an SFP module with the latch opened into
the SFP receptacle on the Radio connector then
lock in place by raising the latch.
4. Replace the protective weather cap for hoisting
or if cable is not ready.
5. Repeat this procedure for each Remote Radio
as required.
Ericsson Internal | 2016-08-23 | Page 54 (57)
New Jumper connections
• 4.3-10 Key features
• Excellent RL and PIM performances independently from
the torque applied or mechanism used
• High screening efficiency
• Electrical contact protected against accidental hits
• Compactness: the connector is fitting in 1 inch flange
(25.4 mm)
• Low weight (60% lighter compared to bigger RF
interfaces)
• 3 possible mechanical connections (screw, hand screw
and quick lock) on 1 universal female connector
• IEC standardization
Ericsson Internal | 2016-08-23 | Page 55 (57)
Radio 2217 fan moduleFan used when installing in non-vertical installation
Fan module
installed
Ericsson Internal | 2016-08-23 | Page 56 (57)
Installing Fan units
1. If required remove the plugs in the radio mounting
holes.
2. Secure the Fan to the side cover. (Alternately the fan
can be installed after the cover)..
3. Orientate the fan unit as shown and slide into place
over the cooling fins of the radio.
4. Secure with the 4 retaining screws and Torque the four
screws to 6 Nm with the Torx 20 driver.
5. Plug the fan cable into the Fan connector on the radio
FAN Connector