New Datasheet - Distec · 2019. 4. 2. · G185XW01 V1 This specification applies to the 18.5...

The information contained in this document has been carefully researched and is, to the best

of our knowledge, accurate. However, we assume no liability for any product failures or

damages, immediate or consequential, resulting from the use of the information provided

herein. Our products are not intended for use in systems in which failures of product could

result in personal injury. All trademarks mentioned herein are property of their respective

owners. All specifications are subject to change without notice.

Datasheet

AUO G185XW01V1

UP-02-059

AU OPTRONICS CORPORATION Product Specification G185XW01 V1

document version 1.2 1

( ) Preliminary Specification ( V ) Final Specification

Module 18.5” Color TFT-LCD Model Name G185XW01 V1

Customer Date

Approved by

Note: This Specification is subject to change without notice.

Approved by Date

Vito Huang 2013/05/14

Prepared by

Elsie Kuo 2013/05/14

Desktop Display Business Group / AU Optronics corporation



Contents

1.0 Handling Precautions............................................................. 4 2.0 General Description ............................................................... 5

2.1 Display Characteristics...........................................................................................................5 2.2 Optical Characteristics ...........................................................................................................6

3.0 Functional Block Diagram.................................................... 10 4.0 Absolute Maximum Ratings ................................................. 11

4.1 TFT LCD Module ..................................................................................................................11 4.2 Absolute Ratings of Environment.........................................................................................11

5.0 Electrical characteristics...................................................... 12 5.1 TFT LCD Module ................................................................................................................. 12 5.1.1 Power Specification.......................................................................................................... 12 5.1.2 Signal Electrical Characteristics....................................................................................... 13 5.2 Backlight Unit....................................................................................................................... 14

6.0 Signal Characteristic............................................................ 15 6.1 Pixel Format Image ............................................................................................................. 15 6.2 The input data format .......................................................................................................... 16 6.3 Signal Description ............................................................................................................... 17 6.4 Timing Characteristics ......................................................................................................... 19 6.5 Timing diagram .................................................................................................................... 20 6.6 Power ON/OFF Sequence .................................................................................................. 21

7.0 Connector & Pin Assignment ............................................... 22 7.1 TFT LCD Module ................................................................................................................. 22 7.2 LED Backlight Unit: LED Driver Connector ........................................................................ 22 7.3 LED Driver Connector Pin Assignment .............................................................................. 23

8.0 Reliability Test..................................................................... 24 9.0 Shipping Label & Packaging................................................. 25

9.1 Shipping Label..................................................................................................................... 25 9.2 Packaging............................................................................................................................ 26 9.3 Palletizing ............................................................................................................................ 27

10.0 Mechanical Characteristics ................................................ 28 11 Safety ................................................................................... 30

11.1 Sharp Edge Requirements................................................................................................ 30 11.2 Materials............................................................................................................................. 30 11.3 Capacitors.......................................................................................................................... 30 11.4 National Test Lab Requirement......................................................................................... 30



Record of Revision

Version & Date Page Old description New Description 0.1 2011/05/13 All First Edition for Customer N/A 0.2 2011/06/13 5 Power Consumption: 14.6W (Typ) Power Consumption:15.3W (Typ)

14 Input Voltage: 5V Input Voltage: 12V

14 Power Consumption: 4.5(Typ), 5.5 (Max).

Power Consumption: 10.8(Typ), 13.2 (Max).

21 Power ON/OFF Sequence Update

1.0 2011/08/12 6 Response Time

Resonse Time:

1.0 2011/08/12 5 & 11 Operating Temperature:

Max. +50°C Operating Temperature: Max. +60°C (as surface temperature)

1.0 2011/08/12 17,18,21,22,23 VDD & VCC Symbol correction

1.0 2011/08/12 26 Add Packaging Info 1.0 2011/08/12 28 Mechanical Drawing (Rear) Update 1.1 2011/11/28 14 Unit of Dimming Frequency: [kHz] [Hz] 1.2 2013/05/14 5 Add Light Bar Unit info- LED replaceable 1.2 2013/05/14 6 Add Color Gamut spec. – 68%

1.2 2013/05/14 14

Add VLED on/off Voltage & FPWM update

1.2 2013/05/14 26. 27 Add packing and palletizing info 1.2 2013/05/14 30 Add safety info



1.0 Handling Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when

handling. 7) Do not open or modify the Module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a Module has to be put back into the packing container slot after it was taken out from the

container, do not press the center of LED lightbar edge. Instead, press at the far ends of the LED light bar edge softly. Otherwise the TFT Module may be damaged.

10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module.

11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even momentarily. While designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.

12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption.

AU OPTRONICS CORPORATION Product Specification


G185XW01 V1

2.0 General Description This specification applies to the 18.5 inch-wide Color a-Si TFT-LCD Module G185XW01 V1.The display supports the WXGA [1366(H) x 768(V)] screen format and 16.7M colors (RGB 6-bits + Hi-FRC data). All input signals are LVDS interface comaptible.

2.1 Display Characteristics The following items are characteristics summary on the table under 25oC condition: ITEMS Unit SPECIFICATIONS Screen Diagonal [mm] 470.1(18.51”) Active Area [mm] 409.8 (H) x 230.4 (V) Pixels H x V 1366(x3) x 768 Pixel Pitch [um] 300 (per one triad) × 300 Pixel Arrangement R.G.B. Vertical Stripe Display Mode TN Mode, Normally White White Luminance ( Center ) [cd/m2] 300 cd/m2 (Typ.) Contrast Ratio 1000 (Typ.) Optical Response Time [msec] 5ms (Typ., on/off) Nominal Input Voltage VDD [Volt] +5.0 V (Typ) Power Consumption (VDD line + LED line) [Watt] 15.3W (Typ.) (Pdd=4.5W,PLED=10.8W) Weight [Grams] 1820(Max) Physical Size [mm] 430.4 (W) x 254.6 (H) Typ. x 16.4(D)Typ Electrical Interface One channel LVDS Support Color 16.7M colors, RGB 6-bit +Hi- FRC Surface Treatment Anti-Glare, 3H Temperature Range Operating Storage (Shipping)

[oC] [oC]

0 to +60 -20 to +60

RoHS Compliance RoHS Compliance Light Bar Unit LED, Replaceable Lightbar



G185XW01 V1

2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25 oC:

Item Unit Conditions Min. Typ. Max. Note Horizontal (Right) CR = 10 (Left)

150

170 - -

Viewing Angle [degree] Vertical (Up) CR = 10 (Down)

140

160 - -

2

Contrast ratio Normal Direction

600

1000 - 3

Raising Time (TrR) - 3.5 5 Falling Time (TrF) - 1.5 2.5 Response Time [msec] Raising + Falling - 5 7.5

4

Red x 0.583 0.633 0.683 Red y 0.296 0.346 0.396 Green x 0.281 0.331 0.381 Green y 0.550 0.600 0.650 Blue x 0.098 0.148 0.198

Color / Chromaticity Coordinates (CIE)

Blue y 0.016 0.066 0.116 White x 0.263 0.313 0.363

Color Coordinates (CIE) White

White y 0.279 0.329 0.379

5

Central Luminance [cd/m2] 240 300 - 6 Luminance Uniformity [%] 65 70 - 7 Crosstalk (in 60Hz) [%] 1.5 8 Flicker dB -20 9 Color Gamut % 68



G185XW01 V1

Note 1: Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring (at surface 35oC). In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and dark room.

Note 2: Definition of viewing angle measured by ELDIM (EZContrast 88) Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle.

Center of the screen

TFT-LCD Module

Measured distance

Photo detector

LCD Panel



G185XW01 V1

Note 3: Contrast ratio is measured by TOPCON SR-3 Note 4: Definition of Response time measured by Westar TRD-100A The output signals of photo detector are measured when the input signals are changed from “Full Black” to “Full White” (rising time, TrR), and from “Full White” to “Full Black” (falling time, TfF), respectively. The response time is interval between the 10% and 90% (1 frame at 60 Hz) of amplitudes. TrR + TfF = 5 msec (typ.).

Note 5: Color chromaticity and coordinates (CIE) is measured by TOPCON SR-3 Note 6: Central luminance is measured by TOPCON SR-3 Note 7: Luminance uniformity of these 9 points is defined as below and measured by TOPCON SR-3

9)-(1 Points 9in LuminanceMaximum 9)-(1 points 9in LuminanceMinimum Uniformity =

Note 8: Crosstalk is defined as below and measured by TOPCON SR-3

CT = | YB – YA | / YA × 100 (%)

100 90

10 0

%

Optical response

White

Tr F Tr R

100

10 0

%

Optical response

White Black

Tr F Tr R

Black

1 Frame 1 Frame



G185XW01 V1

Where YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2)

Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3

R G B R G B

R G B R G B

R G B R G B

Method: Record dBV & DC value with TRD-100

Level DCHz) 30Level(at AClog20(dB)Flicker =

Gray Level = L127

Gray Level = L0

Amplitude

Time

DC

AC



G185XW01 V1

3.0 Functional Block Diagram The following diagram shows the functional block of the 18.5 inch Color TFT-LCD Module:

I/F + X-PCB I/F PCB Interface: FI-XB30SSRL-HF16(JAE)/MSCKT2407P30HB(信盛) Mating Type: FI-X30HL (JAE)(Locked Type)

TFT-LCD 1366(x3) x 768

Pixels

G1

G768 D1 D4098

LED Driver DC POWER

Connector

DC/DC Converter

LVDS Receiver

Timing Controller

RSDS Transmitter

Gamma Correction

AUO ASIC

LVDS

+5V X-Driver IC

Y-Driver IC



G185XW01 V1

4.0 Absolute Maximum Ratings Absolute maximum ratings of the module are as following: 4.1 TFT LCD Module

4.2 Absolute Ratings of Environment Item Symbol Min. Max. Unit Conditions

Operating Temperature TOP 0 +60 [oC] Operation Humidity HOP 5 90 [%RH] Storage Temperature TST -20 +60 [oC] Storage Humidity HST 5 90 [%RH]

Note 3 & 4

Note 1: With in Ta (25 oC) Note 2: Permanent damage to the device may occur if exceeding maximum values Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard). Note 4: Operation Temperature + 60°C is defined as panel surface termperature.

Operating Range Storage Range

Item Symbol Min Max Unit Conditions Logic/LCD Drive

Voltage VDD 4.5 +5.5 [Volt] Note 1,2



G185XW01 V1

5.0 Electrical characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Input power specifications are as follows:

Note 1: Measurement conditions: The duration of rising time of power input is 470us.

+5.0V

+12.0V

VCC

R147K

R2

1K

VR147K

SW1SW MAG-SPST

12

F1

Q3AO6402

G

D2

SD1

D5

D6

C11uF/16V

Q3AO6402

G

D2 SD1

D5D6

C3

0.01uF/25V

C21uF/25V

(High to Low)ControlSignal

(LCD Module Input)

Symbol Parameter Min Typ Max Unit Conditions VDD Logic/LCD Drive Voltage

4.5

5.0 5.5

[Volt] +/-10%

IDD Input Current - 0.9 1.1

[A] VDD= 5.0V, All Black Pattern At 60Hz, PDD VDD Power - 4.5 5.5 [Watt] VDD= 5.0V, All Black Pattern At 60Hz

IRush Inrush Current - - 3 [A] Note 1

VDDrp Allowable Logic/LCD Drive Ripple Voltage - - 200 [mV] p-p VDD= 5.0V, All Black Pattern At 60Hz



G185XW01 V1

5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when VDD is off. Please refer to specifications of SN75LVDS82DGG (Texas Instruments) in detail. Characteristics of each signal are as follows:

Symbol Parameter Min Typ Max Units Condition VTH Differential Input High

Threshold - +50 +100 [mV] VICM = 1.2V Note 1

VTL Differential Input Low Threshold -100 -50 - [mV] VICM = 1.2V

Note 1 VID Input Differential Voltage 100 400 600 [mV] Note 1

VICM Differential Input Common Mode Voltage +1.0 +1.2 +1.4 [V] VTH-VTL = 200MV (max)

Note 1 Note 1: LVDS Signal Waveform

VVID

VICM

VSS



G185XW01 V1

5.2 Backlight Unit Following characteristics are measured under a stable condition at 25 oC (Room Temperature):

Symbol Parameter Min. Typ. Max. Unit Remark VCC Input Voltage 10.8 12 13.2 [Volt] IVCC Input Current 0.9 1.1 [A] 100% PWM Duty PVCC Power Consumption 10.8 13.2 [Watt] 100% PWM Duty

Irush LED Inrush Current - 3 [A] at rising time=470us On Control Voltage 3 5 5.5 Volt

VLED on/off Off Control Voltage 0.8 Volt Dimming Frequency 200 - 20k [Hz]

Swing Voltage 3 3.3 5 V High Voltage 3 3.3 5.5 Volt Low Voltage 0.2 Volt

FPWM

Dimming Duty Cycle 5 - 100 % IF LED Forward Current 80 mA Ta = 25 oC VF LED Forward Voltage - 3.2 3.6 Volt IF =mA, Ta = 25oC

PLED LED Power Consumption - 10.08 Watt IF =mA, Ta = 25oC

Operation Lifetime

50,000 Hrs IF=mA, Ta= 25oC Note 1: Ta means ambient temperature of TFT-LCD module. Note 2: VCC, Ivcc, PVCC , Irush LED are defined for LED B/L.(100% duty of PWM dimming) Note 3: IF, VF , PLED are defined for LED Light Bar. Note 4: If G185XW01 V1 module is driven by high current or at high ambient temperature & humidity condition. The

operating life will be reduced. Note 5: Operation life means brightness goes down to 50% initial brightness. Minimum operating life time is estimated

data.



G185XW01 V1

6.0 Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship of the input signals and LCD pixel format.

R G B R G B

R G B R G B

R G B R G B

R G B R G B

1 2 1365 1366

1st Line

768 Line



G185XW01 V1

6.2 The input data format

LVDS Data Mapping of NS Format

Note1: Normally, DE, VS, HS on EVEN channel are not used. Note2: 8-bits signal input.



G185XW01 V1

6.3 Signal Description The module using one LVDS receiver SN75LVDS82(Texas Instruments). LVDS is a differential signal technology for LCD interface and high speed data transfer device. LVDS transmitters shall be SN75LVDS83(negative edge sampling). The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels.

PIN # SIGNAL NAME DESCRIPTION 1 NC No contact (For AUO internal use) 2 NC No contact (For AUO internal use) 3 NC No contact (For AUO internal use) 4 GND Power Ground 5 RXIN0- Negative LVDS differential data input (0) 6 RXIN0+ Positive LVDS differential data input (0) 7 GND Power Ground 8 RXIN1- Negative LVDS differential data input (1) 9 RXIN1+ Positive LVDS differential data input (1) 10 GND Power Ground 11 RXIN2- Negative LVDS differential data input (2) 12 RXIN2+ Positive LVDS differential data input (2) 13 GND Power Ground 14 RXCLKIN- Negative LVDS differential clock input (clock) 15 RXCLKIN+ Positive LVDS differential data input (clock) 16 GND Power Ground 17 RXIN3- Negative LVDS differential data input (3) 18 RXIN3+ Positive LVDS differential data input (3) 19 GND Power Ground 20 NC No contact (For AUO internal use) 21 NC No contact (For AUO internal use) 22 NC No contact (For AUO internal use) 23 GND Power Ground 24 GND Power Ground 25 GND Power Ground 26 VDD +5V power supply 27 VDD +5V power supply 28 VDD +5V power supply 29 VDD +5V power supply



G185XW01 V1

Note1: Start from left side

Note2: Input signals of clock shall be the same timing. Note3: Please follow TV VESA Pin Assignment.

1 30

NC - VDD



G185XW01 V1

6.4 Timing Characteristics Basically, interface timing described here is not actual input timing of LCD module but close to output timing of SN75LVDS82DGG (Texas Instruments) or equivalent.

Signal Item Symbol Min Typ Max Unit Period Tv 776 808 1023 Th Active Tdisp(v) 768 768 768 Th V-section

Blanking Tblk(v) 8 40 255 Th Period Th 1416 1606 2047 Tclk Active Tdisp(h) 1366 1366 1366 Tclk H-section

Blanking Tblk(h) 50 240 681 Tclk Period Tclk - 12.8 - ns Clock Frequency Freq - 78 90 MHz

Frame Rate Frame Rate F 50 60 75 Hz

Note1 : DE mode only Note2 : Clock Frequency 90MHz(Max.)= 1416(H)*847(V)*75Hz



G185XW01 V1

6.5 Timing diagram



G185XW01 V1

6.6 Power ON/OFF Sequence VDD power and LED on/off sequence are as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off.

Power ON/OFF sequence timing

Value Parameter Min. Typ. Max.

Units

T1 0.5 - 10 [ms] T2 0 40 50 [ms] T3 200 - - [ms] T4 0.5 - 10 [ms] T5 10 - - [ms] T6 10 - - [ms] T7 0 - - [ms] T8 10 - - [ms] T9 - - 10 [ms] T10 110 - - [ms] T11 0.5 16 50 [ms] T12 - - 100 [ms] T13 1000 - - [ms]

90%

10%

90%

10%

10%

90%

90%

90%

90%

10%

10%

10%

T1T1T1T1 T2T2T2T2

T3T3T3T3

T4T4T4T4 T5T5T5T5

T6T6T6T6 T7T7T7T7

T10T10T10T10

T8T8T8T8 T9T9T9T9

T11T11T11T11 T12T12T12T12 T13T13T13T13

VDDVDDVDDVDD

SignalSignalSignalSignal

VVVVCCCCCCCC

Back light dimmingBack light dimmingBack light dimmingBack light dimming

Back light on/offBack light on/offBack light on/offBack light on/off

10%

10%

90%

90%



G185XW01 V1

7.0 Connector & Pin Assignment Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components.

7.1 TFT LCD Module Connector Name / Designation Interface Connector / Interface card Manufacturer JAE or CHIEF LAND Type Part Number FI-XB30SRL-HF11(JAE) / 093F30-B0T01A(CHIEF LAND) Mating Housing Part Number FI-X30HL(JAE) (Locked Type)

FI-X30H (JAE)(Unlocked Type) 7.1.1 Pin Assignment

Pin# Signal Name Pin# Signal Name 1 NC 2 NC 3 NC 4 GND 5 RXIN0- 6 RXIN0+ 7 GND 8 RXIN1- 9 RXIN1+ 10 GND 11 RXIN2- 12 RXIN2+ 13 GND 14 RXCLKIN- 15 RXCLKIN+ 16 GND 17 RXIN3- 18 RXIN3+ 19 GND 20 NC 21 NC 22 NC 23 GND 24 GND 25 GND 26 VDD 27 VDD 28 VDD 29 VDD 30 VDD

7.2 LED Backlight Unit: LED Driver Connector

Connector Name / Designation LED Connector Manufacturer E&T or compatible Connector Model Number 3808K-F05N-02R or compatible



G185XW01 V1

7.3 LED Driver Connector Pin Assignment

Pin# Symbol Signal Name 1 VCC 12V 2 GND GND 3 Enable 5V-On / 0V-Off 4 Dimming PWM Dimming 5 NC NC



G185XW01 V1

8.0 Reliability Test Environment test conditions are listed as following table.

Items Required Condition Note Temperature Humidity Bias (THB) Ta= 50oC, 80%RH, 300hours

High Temperature Operation (HTO) Ta= 60oC, 50%RH, 300hours

Low Temperature Operation (LTO) Ta= 0oC, 300hours

High Temperature Storage (HTS) Ta= 60oC, 300hours

Low Temperature Storage (LTS) Ta= -20oC, 300hours

Vibration Test (Non-operation)

Acceleration: 1.5 Grms Wave: Random Frequency: 10 - 200 Hz Sweep: 30 Minutes each Axis (X, Y, Z)

Shock Test (Non-operation)

Acceleration: 50 G Wave: Half-sine Active Time: 20 ms Direction: ±X, ±Y, ±Z (one time for each Axis)

Drop Test Height: 60 cm, package test

Thermal Shock Test (TST) -20oC /30min, 60oC /30min, 100 cycles 1 On/Off Test On/10sec, Off/10sec, 30,000 cycles

Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point.

ESD (Electro Static Discharge) Air Discharge: ± 15KV, 150pF(330Ω ) 1sec 8 points, 25 times/ point.

2

Altitude Test Operation:10,000 ft Non-Operation:30,000 ft

Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid temperature change. A cycle of rapid temperature change consists of varying the temperature from -20oC to 60oC, and back again. Power is not applied during the test. After temperature cycling, the unit is placed in normal room ambient for at least 4 hours before power on. Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.

Self-recoverable. No hardware failures.



G185XW01 V1

9.0 Shipping Label & Packaging 9.1 Shipping Label The label is on the panel as shown below:

Note 1: For Pb Free products, AUO will add for identification. Note 2: For RoHS compatible products, AUO will add for identification. Note 3: For China RoHS compatible products, AUO will add for identification. Note 4: The Green Mark will be presented only when the green documents have been ready by AUO Internal Green Team.



G185XW01 V1

9.2 Packaging Max capacity：8 TFT-LCD module per carton Max weight: 14.2 kg per carton Outside dimension of carton: 519mm(L)* 279mm(W)*332mm(H) Pallet size：1140 mm *1060 mm *135mm



G185XW01 V1

9.3 Palletizing Box stacked

Max_ Module by air：(2 *4) *4 layers，one pallet put 32 boxes，total 256pcs module Max_ Module by sea：(2 *4) *3 layers + (2 *4) *2 layers , two pallet put 40 boxes，total 320pcs module Max_ Module by sea_HQ：(2 *4) *3 layers+(2 *4) *3 layers, two pallet put 36 boxes, total 384pcs module

AU O

PTRO

NICS

CO

RPO

RATI

ON

Prod

uct S

pecif

icatio

n

docu

men

t ver

sion

1.2

28

G18

5XW

01 V

1

10.0

Mec

hani

cal C

hara

cter

istic

s

AU O

PTRO

NICS

CO

RPO

RATI

ON

Prod

uct S

pecif

icatio

n

docu

men

t ver

sion

1.2

29

G18

5XW

01 V

1



G185XW01 V1

11 Safety 11.1 Sharp Edge Requirements

There will be no sharp edges or comers on the display assembly that could cause injury.

11.2 Materials 11.2.1 Toxicity

There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO toxicologist.

11.2.2 Flammability All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board.

11.3 Capacitors If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards.

11.4 National Test Lab Requirement The display module will satisfy all requirements for compliance to:

UL 60950-1, Second Edition U.S.A. Information Technology Equipment

Our company network supports you worldwide with offices in Germany, Austria, Switzerland, the UK and the

USA. For more information please contact:

Headquarters

Germany FORTEC Elektronik AG

Lechwiesenstr. 9

86899 Landsberg am Lech

Phone: +49 8191 91172-0

E-Mail: [email protected]

Internet: www.fortecag.de

Fortec Group Members

Austria FORTEC Elektronik AG

Office Vienna

Nuschinggasse 12

1230 Wien

Phone: +43 1 8673492-0


Internet: www.fortec.at

Germany Distec GmbH

Augsburger Str. 2b

82110 Germering

Phone: +49 89 894363-0


Internet: www.distec.de

Switzerland ALTRAC AG

Bahnhofstraße 3

5436 Würenlos

Phone: +41 44 7446111


Internet: www.altrac.ch

United Kingdom Display Technology Ltd.

Osprey House, 1 Osprey Court

Hichingbrooke Business Park

Huntingdon, Cambridgeshire, PE29 6FN

Phone: +44 1480 411600


Internet: www. displaytechnology.co.uk

USA Apollo Display Technologies, Corp.

87 Raynor Avenue,

Unit 1Ronkonkoma,

NY 11779

Phone: +1 631 5804360


Internet: www.apollodisplays.com

mailto:[email protected]

http://www.fortecag.de/


http://www.fortec.at/


http://www.distec.de/


http://www.altrac.ch/



http://www.apollodisplays.com/

Date post:	16-Oct-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

New Datasheet - Distec · 2019. 4. 2. · G185XW01 V1 This specification applies to the 18.5...

Documents