Contact: Kathrin Steimle Marketing & Communication Coperion GmbH Theodorstraße 10 70469 Stuttgart / Germany Phone +49 (0)711 897 25 07 Fax +49 (0)711 897 39 81 [email protected] www.coperion.com
Press Release Coperion Open House in Stuttgart/Germany on 28th and 29th January 2009
New developments for greater reliability in operation when compounding at high output rates Stuttgart, February 2009 – Given the same size of machine, the co-rotating twin-screw
extruders of the ZSK MEGAcompounder and ZSK MEGAcompounder PLUS series have an
output capacity many times greater than that of their forerunners. The decisive factors for the
increase in output are the optimized screw geometry (Do : Di = 1.55, where 'Do' is the outer
diameter and 'Di' the inner diameter of the screw), the increase in available torque at the screw
shafts (specific torque Md / a³ = 13,6 Nm/cm3, where 'a' is the centre-to-centre distance between
the screws) and the resulting possible increase in screw speed to 1,200 r.p.m. and over. By
reason of its enormous processing competence and expertise – as Dr. Peter Heidemeyer
explained at the Coperion Open House in Stuttgart/Germany in January 2009 – Coperion is
able to combine this performance increase with other innovative measures in order to achieve
high outputs in a great many different processes while at the same time maintaining, or even
increasing, reliability in operation. Moreover, Coperion ensures, not least through its well-
coordinated material and process technology, that machine wear is reduced to a minimum and
product quality is optimized in spite of the extremely high energies that have to be converted
mechanically.
Innovative solutions for feeding and venting zones Among the most important innovative measures are the improvements in the feeding zone and
the installation of a twin-screw side venting unit. In processes with feed limitations, e.g. when
processing products of low bulk density and hence high air and moisture content, the feed
February 2009
page 2 from 6
capacity can be considerably increased with the aid of so-called Feed Enhancement
Technology (FET). With this technology, the feeding zone is provided with a porous, gas-
permeable wall, to the exterior of which a vacuum is applied, enabling the feeding zone to take
in a much larger volume of material and hence also contributing to an improvement in the
melting process in the downstream section of the extruder, as the volume of gas entrained by
the material into this section is considerably reduced. The geometry of the screw in the feeding
zone has also been optimized. Especially when processing products with such feed limitations
as those described above, and without waiving any reliability of operation whatsoever, these
two measures together can double or triple the volume of material fed into the extruder! FET
can be used not only on the twin-screw extruder itself but also, and with the same feed-
enhancing effect, on the ZS-B twin-screw side-feeder systems. Thus it is possible to feed low-
density products into the compounding extruder downstream of the feeding zone and at a high
rate of feed. Typical FET applications are, for example, the production of highly talc-filled or
chalk-filled compounds, the filling of polypropylene with microscopic hollow glass beads, the
compounding of wood-polymer composites (WPC) or the production of masterbatch.
The new ZS-EG twin-screw side venting unit fully matches the high capacity of the
MEGAcompounder PLUS. Its twin screws hold back the melt in the compounding extruder and
enable the gas to vent in the opposite direction to their conveying direction. The unit's high
venting capacity is made possible by its deep-flighted screws, while the relatively low speed of
the vented gas ensures that hardly any product residues are entrained out of the extruder by the
gas. Any residual product that does find its way out of the extruder is separated from the gas
stream before it can enter the vacuum pump. Thanks to its side mounting position, the ZS-EG
is user-friendly; it can be swung to one side for full and easy access to its interior. Its typical
applications are, for example, the production of glass fibre reinforced or highly filled compounds,
wood-polymer composites (WPC) or thermoplastic elastomers (TPE).
The importance of materials for wear resistance The available materials for the barrel and the screw elements differ considerably not only in
terms of abrasion and corrosion resistance but also in respect of cost. Naturally, an optimum
choice of materials is not possible without precise knowledge of the intended application. Using
the HIP process (Hot Isostatic Pressing), for example, the barrel can be rendered abrasion and
February 2009
page 3 from 6
corrosion resistant by providing its basic ductile/malleable steel body with a wear-resistant
coating having a hardness of 60 to 65 HRC. In the case of screw elements, particularly good
results can be obtained with a protective layer produced with the aid of CVD technology
(chemical vapour deposition) on a highly wear-resistant powered-metallurgical sintered steel.
Aids to making product development fast and transparent A newly introduced quick-release coupling for small compounders (ZSK 18 to 34) permits very
fast screw change. It shortens the cleaning times, for example, when changing over from one
product or colour to another, thus enabling the user to make better use of available capacity.
The coupling has male and female connectors – similar to those of a garden hose coupling –
and is very easy to use.
Complementing the above-described new developments are newly introduced aids for the
development of new plastic products.
• Sampling plate for speeding up product development: The plate enables the user to take a
specimen from the extruder barrel in less than 10 seconds, even if the extruder barrel is only
partially filled. It is available for use with ZSKs with screw diameters ranging from 18 to
92 mm.
• See-through barrel plug quite literally makes product development transparent. It permits the
user to observe the process in the extruder barrel. It will withstand temperatures of up to
250 °C, has a large observation window and can be used on ZSK sizes up to 40/43.
Coperion (www.coperion.com) is the international market and technology leader in compounding systems, bulk materials handling systems and services. Coperion designs, develops, manufactures and maintains systems, machines and components for the plastics, chemicals, food and aluminium industries. With its three Competence Centers – Compounding & Extrusion, Materials Handling, Service – and over 30 sales and service companies, Coperion achieves annual sales of over 600 million euros worldwide and has a total work force of 2,100 employees.
February 2009
page 4 from 6
Dear Colleagues, an MS-WORD file of this press release in English and German and a printable-grade copy of the enclosed image are available for download at http://www.coperion.com/technicalpress
Editorial contact and voucher copies:
Dr. Diether Burkhardt, KONSENS Public Relations GmbH & Co. KG, Hans-Kudlich-Straße 25, D-64823 Groß-Umstadt Phone: +49 (0)60 78/93 63-0, Fax: +49 (0)60 78/93 63-20 E-Mail: [email protected], Internet: www.konsens.de
February 2009
page 5 from 6
Fig. 1. The ZS-EG 70 twin-screw side venting unit, shown here mounted on a ZSK
MEGAcompounder PLUS, is distinguished by its high venting capacity and reliability in
operation; it can simply be swung to one side for maintenance and cleaning purposes.
Photo: Coperion, Stuttgart/Germany
February 2009
page 6 from 6
Fig. 2. This quick-release coupling permits very fast screw change; it is available for small
compounders ranging from ZSK 18 to ZSK 24.
Photo: Coperion, Stuttgart/Germany
Contact: Kathrin Steimle Marketing & Communication Coperion GmbH Theodorstrasse 10 70469 Stuttgart / Germany Phone +49 (0)711 897 25 07 Fax +49 (0)711 897 39 81 [email protected] www.coperion.com
Press Release Coperion Open House in Stuttgart/Germany on 28th and 29th January 2009
Turnkey compounding lines in modular design – from one single supplier Stuttgart, February 2009. – In view of the steadily growing demand for its modular plants for the
compounding of plastics, Coperion GmbH, Stuttgart/Germany, has considerably widened not
only the scope of application of these systems but also their performance range. At present,
there are a good 50 such systems in service worldwide. Coperion is the only single-source
manufacturer able to offer a complete system from start to finish backed by the collective know-
how of two Competence Centers, Compounding & Extrusion as well as Materials Handling: raw
material handling, feeding, compounding and pelletizing, drying, conveying and bagging of the
finished goods. The advantages for the user: he has only one supplier to deal with and need
not concern himself with the mechanical or electrical connections and/or interfaces between the
individual system units, which would be the case if the system units were all sourced from
different suppliers.
Today, the market especially demands compounding systems with an output capacity of
anything between 2,000 and 3,500 kg/h. For such high-capacity applications, depending on the
actually required output and the type of product, Coperion offers either a ZSK 70 or a ZSK 92
MEGAcompounder PLUS. A typical example is a complete turnkey plant equipped with a
ZSK 92 MEGAcompounder PLUS for the production of glass fibre reinforced polyamide (PA)
compounds. It is contained in a steel structure with two overhead working platforms and pre-
hopper integrated cranes and comprises the following main modules:
• the pre-hopper module for bulk storage and refilling of material to be fed into the ZSK;
February 2009
page 2 from 6
• the feeder module for the various PA grades and the necessary fillers and additives;
• the ZSK module as the compounding extruder, installed at floor level and equipped with a
92 mm diameter screw; and
• the downstream modules such as the pelletizing unit, the cooling unit, the silos for the
finished product and the bagging unit.
Prior to delivery, this complete turnkey production line was, like all such systems, completely
assembled at the Competence Center Compounding & Extrusion (formerly Werner & Pfleiderer)
and tested under production-specific conditions in the presence of the customer. It was with the
aid of this example, among others, that Steffen Bader, Business Segment Manager Modular-
and Turnkey Plants, explained the particular user benefits of such pre-tested turnkey plants at
the Coperion Open House in January 2009. Size and capacity may range from the ZSK 26
MEGAcompounder up to systems with a screw diameter of 133 mm and/or output ratings of up
to 5 t/h. The equipment variations possible with modular plants are exemplified not least by the
downstream module. Besides the usual strand pelletizer, for example, it is also possible to
equip the downstream module with waterring pelletizers or underwater pelletizers with varying
drying systems. Further examples of existing modular plants include compounding lines for
direct long-fibre thermoplastic (D-LFT) compounding or for the production of special compounds
for the insulation of offshore pipes.
Coperion generally understands a modular line to mean a completely equipped compounding
line built up from standardized modules. These modules cover all stages of operation and
range from the upstream handling of raw materials via feeding systems to the downstream
bagging and logistical handling of the finished product. It goes without saying that the modular
concept also embraces a uniform and user-friendly control and automation technology for the
entire system. The individual units are each contained in a steel structure that can be readily
separated – via just a few interfaces – for easy transport. This form of construction offers
numerous advantages, e.g.:
• Every modular plant can be thoroughly tested at Coperion's production facility prior to
delivery. Trial production runs can also be carried out, thus providing the future operator with
sample quantities for opening up of a new market.
February 2009
page 3 from 6
• The modular plant can be quickly installed and put into service. The operating personnel can
already be trained during the trial production runs at Coperion.
• The modular plant makes no particular demands on the building in which it is installed –
except for the required headroom and the load-bearing capacity of the floor.
• The modular plant can be quickly transferred to another location if required.
• Every modular plant is equipped with a uniform, user-friendly control system that unifies all
functions under one common user interface.
• A modular plant can be readily installed in an existing production facility, even in a confined
space, without unduly affecting the production of the adjacent production lines.
Every modular and turnkey plant is designed and engineered by Coperion exactly in
accordance with the actual requirements of the customer. For its choice of the materials
handling units, the ZSK equipment and peripherals and the configuration of the screw, Coperion
can rely on its vast processing know-how acquired in the fields of materials handling and
extrusion. Coperion modular and turnkey plants are in service worldwide.
Coperion (www.coperion.com) is the international market and technology leader in compounding systems, bulk materials handling systems and services. Coperion designs, develops, manufactures and maintains systems, machines and components for the plastics, chemicals, food and aluminium industries. With its three Competence Centers – Compounding & Extrusion, Materials Handling, Service – and over 30 sales and service companies, Coperion achieves annual sales of over 600 million euros worldwide and has a total work force of 2,100 employees.
Dear Colleagues, an MS-WORD file of this press release in English and German and a printable-grade copy of the enclosed image are available for download at http://www.coperion.com/technicalpress
Editorial contact and voucher copies:
Dr. Diether Burkhardt, KONSENS Public Relations GmbH & Co. KG, Hans-Kudlich-Straße 25, D-64823 Groß-Umstadt Phone: +49 (0)60 78/93 63-0, Fax: +49 (0)60 78/93 63-20 E-Mail: [email protected], Internet: www.konsens.de
February 2009
page 4 from 6
Fig. 1. Photo of pre-tested turnkey modular plant comprising the raw materials handling
module, a ZSK 92 MEGAcompounder PLUS for the compounding of polyamide. Taken during
trials at Coperion.
Photo: Coperion, Stuttgart/Germany
February 2009
page 5 from 6
Fig. 2. Waterbath, pelletizer and spiral cooling conveyor in a modular plant awaiting acceptance
test at Coperion.
Photo: Coperion, Stuttgart/Germany
February 2009
page 6 from 6
Fig. 3. The modular plant for laboratory and development applications, equipped with a ZSK 26
MEGAcompounder, affords plenty of space and flexibility.
Photo: Coperion, Stuttgart/Germany
Contact: Kathrin Steimle Marketing & Communication Coperion GmbH Theodorstrasse 10 70469 Stuttgart / Germany Phone +49 (0)711 897 25 07 Fax +49 (0)711 897 39 81 [email protected] www.coperion.com
Press Release Coperion Open House in Stuttgart on 28th and 29th January 2009
Four years' success with the ZSK MEGAcompounder PLUS Stuttgart, February 2009. – Since the introduction of the ZSK MEGAcompounder PLUS four
years ago, Coperion GmbH, Stuttgart/Germany, has already sold 600 machines of this type,
thus considerably exceeding the number of sales of its forerunner, the ZSK MEGAcompounder.
This was one of the items of news conveyed by Peter von Hoffmann, General Manager
Business Unit Engineering Plastics & Masterbatch of the Competence Center
Compounding & Extrusion (formerly Werner & Pfleiderer) at the Coperion Open House in
Stuttgart on 28th and 29th January 2009. This twin-screw high-performance compounder has a
20% higher torque rating than its forerunner and is therefore primarily suitable for compounding
applications requiring a high energy input. And since the higher torque rating permits a higher
filling rate, the output is typically 30% higher, while the temperature of the product may in many
cases even be reduced. As numerous cases of practical application have shown, this
advantage makes the ZSK MEGAcompounder PLUS an extremely economical and versatile
compounder and explains the enormous success it is enjoying in the market.
The outstanding performance of the ZSK MEGAcompounder PLUS really comes into its own
when compounding glass fibre reinforced polymers. Here the glass fibres are fed downstream
straight into the already plasticized matrix material, thus avoiding not only damage to the glass
fibres but also screw abrasion in the processing section. Depending on the configuration of the
machine, the glass fibres can be added in the form of chopped strands or straight from the
roving. The use of other fibres (e.g. carbon fibres) and combinations with other reinforcing
agents and/or fillers is also possible. In this way it is possible to produce compounds with up to
February 2009
page 2 of 5
60% w/w glass fibres. Machines configured and rated for such high performance are generally
equipped with an adequate number of venting devices in order to ensure a high quality of
product.
Comparative compounding trials with polypropylene with a 30% w/w glass fibre content have
shown that the ZSK MEGAcompounder PLUS can achieve an increase in output of 30% and
more in comparison with its forerunner. Here the melt index (MFI) of the product remains
virtually the same, while its notched impact strength and its tensile strength are slightly higher.
The reason for this improvement in product properties lies in the reduced shear input for each of
the three screw speeds used for the trials (600, 900 and 1,200 r.p.m.), which in turn resulted in
a reduction in product temperature by around 7 °C.
Similar results were obtained with compounding trials with a polyamide (PA 6.6) with a 30% w/w
glass fibre content. Even in the case of a polybutylene terephthalate (PBT) compound, likewise
reinforced with a 30% w/w glass fibre content, it was possible to increase the output of just
under 5,000 kg/h on a ZSK 92 Mc to 6,000 kg/h on a ZSK 92 Mc PLUS (screw speed
800 r.p.m.), while the specific energy consumption was reduced.
A further innovative application is the production of PET film from non-pre-dried PET. For this
application the ZSK MEGAcompounder PLUS is equipped with one atmospheric and two
vacuum venting devices. Even at the same screw speed, the output achieved by the
ZSK MEGAcompounder PLUS is 20% higher than that of its forerunner. The higher torque
rating, however, permits an increase in screw speed from 200 to 300 r.p.m. This advantage
may be exploited in two possible ways: either the intrinsic viscosity (IV) of the PET can be
allowed to drop, as before, from an input value of 0.81 g/dl to an output value of 0.78 g/dl (i.e.
the quality of the product remains unchanged), which means that the output rate can be
increased by a total of 75%; or only the 20% increase in output is utilized, without increasing the
screw speed, in which case an intrinsic viscosity of almost 0.80 g/dl can be obtained, and hence
a considerably better quality of product.
February 2009
page 3 of 5
Similarly, when compounding an acrylonitrile-butadiene-styrene copolymer (ABS) +
polycarbonate (PC) + 20% w/w glass fibre content, it was possible, thanks to the higher torque
rating, to increase the output rate by 25%, while the temperature of the product was lower by up
to 20 °C. This drop in temperature permits an increase in screw speed, and hence an increase
in output, which, during the trials, was even as high as 80%.
Profitability comparison: amortization period reduced by 25%
With particular reference to the production of glass fibre reinforced PBT it has been possible to
do a profitability comparison between the ZSK MEGAcompounder PLUS and its forerunner, the
ZSK MEGAcompounder, on the basis of actual practical experience, as one of Coperion's
customers operates both types of machine. The profitability calculation is based on an increase
in output from 4,900 to 6,000 kg/h and on a reduction in specific energy. The results clearly
show that the amortization period is further reduced by around 25%.
Coperion (www.coperion.com) is the international market and technology leader in compounding systems, bulk materials handling systems and services. Coperion designs, develops, manufactures and maintains systems, machines and components for the plastics, chemicals, food and aluminium industries. With its three Competence Centers – Compounding & Extrusion, Materials Handling, Service – and over 30 sales and service companies, Coperion achieves annual sales of over 600 million euros worldwide and has a total work force of 2,100 employees.
Dear Colleagues, an MS-WORD file of this press release in English and German and a printable-grade copy of the enclosed image are available for download at http://www.coperion.com/technicalpress
Editorial contact and voucher copies:
Dr. Diether Burkhardt, KONSENS Public Relations GmbH & Co. KG, Hans-Kudlich-Straße 25, D-64823 Groß-Umstadt Phone: +49 (0)60 78/93 63-0, Fax: +49 (0)60 78/93 63-20 E-Mail: [email protected], Internet: www.konsens.de
February 2009
page 4 of 5
Fig. 1. For the compounding of polypropylene reinforced with 30% w/w glass fibres, the
ZSK 50 Mc PLUS achieves an increase in output of up to 33% (right) and even produces a
better quality of product, as the comparison with a ZSK 50 Mc shows (left)
Graph: Coperion, Stuttgart/Germany
February 2009
page 5 of 5
Fig. 2. Powerful, efficient and hence suitable for all compounding applications requiring a high
input of energy, the ZSK MEGAcompounder PLUS is shown here in its "compact" form, i.e. with
attached control cabinet and equipped with a 70 mm diameter screw.
Photo: Coperion, Stuttgart/Germany