Model 502 (Shown with an Inclined Conveyor)

Sales and Marketing

Part #: 14153A

R1N 3C5

602652

sales@ndeco.com

502 - 802 Series

Parts Manual

New Direction Equipment

NDENDENDENDEVertical Cutter / Mixer / Feeder

www.ndeco.com

July 2005

Models in Series

English Language Version 2

Sioux Falls, SD USA 57103401 East 8th Street, Suite 219New Direction Equipment

702802

502552

New Direction Equipment1000 6th Ave. NEPortage La Prairie, MB

Manufacturing Plant

Model 502 (Shown with a Flat Conveyor)

Sales and Marketing

Fax 1-204-239-4271

please contact a NDE representative using the contact information below.To obtain replacement parts, please contact your NDE dealer for service. To locate the nearest dealer

Tel. 1-605-336-3127Fax 1-605-336-3189

- Part Numbers

New Direction Equipment

provided in your Operator's Manual.

Contact Information

Ordering Parts

To ensure warranty support for your NDE machine, please fill out the warranty registration card

first section, the Final Assembly in the second section and the Optional Equipment in the third section.This Manual contains the Parts for the 502 to 802 series Machines. Subassemblies are located in the

- Quantities Required

Serial No.: _____________________________________

Model: ________________________________________

See your local NDE dealer for details regarding recently published updates. Note: This Parts Manual is subject to change without notice.

Owner: ________________________________________

- Model and Serial Number of the specific machine

57103Sioux Falls, South Dakota401 East 8th Street, Suite 219New Direction Equipment

R1N 3C5Portage La Prairie, MB1000 6th Ave. NE

When ordering parts please have the following information on hand:

Email: sales@ndeco.comWebsite: www.ndeco.comToll Free (North America): 1-888-336-3127

Tel. 1-204-239-4270

Manufacturing Plant

New Direction Equipment

NDENDENDENDE

1-1

Table of Contents

New Direction EquipmentNDENDENDENDE

1-2

Introduction…………….….……….………………....…………………………………………………………1-1

Table of Contents………..….……………………….....…………………………………………………………1-2

Service History Log……….……..………………...…..…………………………………………………………1-3

Subassemblies

Frames……………………………...……………….…………………………………………………………2-1

Hubs and Tires………………………...….…..………..…………………………………………………………2-5

Driveline Shafts…………...……………...….………...…………………………………………………………2-7

Oil Tank & Gearboxes...………………..………………...….……..…………………………………………………………2-9

Augers………...……………………………....…..……..…………………………………………………………2-11

Conveyors…………………...…………….…...…..……………………………………………………………2-13

Final Assembly

Overview……..……………………………….……....……………………………………………………………3-1

Front End Parts...…………………………..…...…..…………………………………………………………3-3

Tub Parts……..……………………….………....…..…………………………………………………………3-7

Conveyor End Shields and Hoses.………..………...…..…………………………………………………………3-9

Decals…………………….…………………….…..…………………………………………………………3-11

Optional Equipment

Platform and Ladders……...……………………...……………………………………………………………4-1

Monitor Pole……………...……………………….….…………………………………………………………4-3

Road Lighting Package………...………………..….…………………………………………………………4-4

Two Speed Auger Drive Kit……………………..…………..…………………………………………………………4-5

Conveyor Feed Slide and Magnet Kits……..………………………..…………………………………………………………4-7

Conveyor Speed Control & Extension Kits………………….…………..…………………………………………………………4-8

Summary Table of all Optional Equipment………………….….…………………………………………………………4-9

Notes…………………………………………....…………………………………………………………5-1

Service History Log

1-3

NDENDENDENDENew Direction Equipment

DATE PART NO./DESCRIPTION COST

(Assemblies 10380, 10381, 10382, 10383 & 10384)

25

39

22

21

1*

5

18

17

2*

1916

13

20

23

24

(10380 - Frame)

6

14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-1

New Direction Equipment

NDENDENDENDE

Frame Subassembly

* Units with last four digits of serial # 1691 and under use spindle 10037 and hub assembly 10039.

Frame Subassembly - Parts List

Frame Assembly Parts Lists

ITEM PART DESCRIPTION 10380/QTY.

10381/QTY.

10382/QTY.

10383/QTY.

10384/QTY.

1* 10037 Spindle 2 2 2 2 -

1* 14157 Spindle- Double, 3" - 10 K - - - - 2*

2* 10039 Hub Assembly - Complete with Hardware 4 4 4 4 -

2* 14244 Hub - 8 Bolt Ag, 1.5 off set - - - - 4*

3 10131 Weighbar - 2-1/8" 4 4 4 4 -

3 10731 Weighbar 700/800/1000 Series - - - - 4

4 10371 WA-Hitch/Frame, 552LP - 1 - - -

4 10372 WA-Hitch/Frame 552 - - 1 - -

4 10373 WA-Hitch/Frame, 502LP - - - 1 -

4 10374 WA-Hitch/Frame, 702 - - - - 1

5 10607 11L x 15 Tire - 4 - 4 -

5 13159 Implement Tire 12.5L x 16, 33" High 4 - 4 - 4

6 10819 Pin - Jack 1 1 1 1 1

7 10987 Loom - Polyethelen, 3/4" (LCP750) (not shown) 12 12 12 12 12

8 14035 Grease - Elbidea Brg (LCEP2) (not shown) 1.15 1.15 1.15 1.15 1.15

9 14082 W.A. - Load Cell Mt, (small hole) 4 4 4 4 -

10 14083 W.A. - Load Cell Mt. - - - - 4

11 14440 Safety Chain - 3/8" X 72", 20,200 LB - 1 1 1 1

12 16609 Loom-Wire, 3/8 Split, per Foot (not shown) 16 16 16 16 16

13 20152 IronWorks Jack 9500 1 1 1 1 1

15 HB.5x8.5 G8 Hex Head Bolt 1/2-13 X 8.5 Gr 8 - 2 - 2 -

16 20348 Weldment - Hitch, 1-1/4 in. hole 1 1 1 1 1

17 FlatWasher Flat washer 1-1/4 SAE 4 4 4 4 4

18 Nut-Castle Hex Castle Nut 1 1/4-12 UNF 4 4 4 4 4

19 hexheadbolt Hex Head Bolt 3/4-10 X 8 Gr 8 2 2 2 2 2

20 Nut-FlangLock Lock Nut -Flange Unitorque 3/4-10 UNC 2 2 2 2 2

21 hexheadbolt Hex Head Bolt 1/2-13 X 4 1/2 Gr 8 2 - 2 - 2

22 Nut-FlangLock Flange Lock Nut-Unitorque -1/2-13NC 2 2 2 2 2

23 hexheadbolt Hex Head Bolt 3/8-16 X 5 Gr 8 4 4 4 4 -

24 Nut-FlangLock Flange Lock Nut-3/8 NC Unitorque 4 4 4 4 -

25 502-802 frameWA

WA-Hitch/Frame, 502 1 - - - -

Association Table

MODEL # 502 502 LP 552 552 LP 602 652 702 802

FRAME PART # 10380 10383 10382 10381 10380 10382 10384 10384

14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-2

New Direction Equipment

NDENDENDENDE

2

19

43

42

47

46 27

40

7

39

45203

4

30

4432

1417

16

12

10

15

8

41

13

28

21

18

245

11

31

9

Assembly 10380 CE & 10384CE

36

25

6

29

Brake Axle Frames

Association TableMODEL # FRAME PART #

502CE 10380CE

602CE 10380CE

702CE 10384CE

802CE 10384CE

2-3

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder

NDENDENDENDE

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-4

NDENDENDENDE

Brake Axle Frames - Parts ListParts List

ITEM PART DESCRIPTION 10380CE/QTY.

10384CE/QTY.

1 10131 Weighbar - 2-1/8" 4 -2 10374CE WA - Frame 702CE/802CE - 12 10370CE WA-Hitch/Frame, 502CE 1 -3 10637 Rim/Tire Assy 16x10x8 bolt METRIC 4 44 10671 Axle - Double with Brake 2 25 10731 Weighbar 700/800/1000 Series - 46 10819 Pin - Jack 1 17 10932 Plate- Support 8 88 10942 Bushing-Brake Plate Spacer 2 29 10943LHP Formed Angle-Brake Lever Mount-LH 1 1

10 10943RHP Formed Angle-Brake Lever Mount-RH 1 111 10946 Plate-Cable Ratchet 1 112 10948 Bar-Ratchet Pawl 1 113 10949 Cable -3/16 x 36" 2 214 10952 Bar-Mechanical Brake Lever 1 115 10953 Plate-Clamping 3 316 10954 Weldment-Engagement Pawl 1 117 10956 Washer Spacer 1 118 10958 Weldment-Cable Wind 701 - 118 14191 WA - Cable Wind 502 1 -19 10960 Support -PTO Shaft 1 120 10966 Plate-Axle Clamp 2 221 10969 Weldment-Pinion Shaft 1 122 10987 Loom - Polyethylene 3/4" (LCP750) 1 123 14082 W.A. - Load Cell Mt, (small hole) 4 -24 14083 W.A. - Load Cell Mt. - 425 14440 Safety Chain - 3/8" X 72", 20,200 LB 1 126 16609 Loom-Wire, 3/8 Split, per Foot (LCP413-2000) 1 127 20152 IronWorks Jack 9500 1 128 CC.1875 Cable Clamp -3/16 2 229 FHN.375 Flange Lock Nut-3/8 NC Unitorque 18 1830 FHN.5 Flange Lock Nut-Unitorque -1/2-13NC 23 2331 FHN.75 Lock Nut -Flange Unitorque 3/4-10 UNC 4 432 FW1.25N Flat washer 1-1/4 SAE 1 133 HB.375x1.25 Hex Head Bolt 3/8-16 X 1 1/4 4 434 HB.375x5 Hex Head Bolt 3/8-16 X 5 8 835 HB.375x5.5 Hex Head Bolt 3/8-16 X 5 1/2 2 236 HB.375x5G8 Hex Head Bolt 3/8-16 X 5 Gr 8 4 437 HB.5x1.25 Hex Head Bolt 1/2-13 X 1.25 2 238 HB.5x1.5 Hex Head Bolt 1/2-13 X 1 1/2 1 139 HB.5x2G8 Hex Head Bolt 1/2-13 X 2 Gr 8 12 1240 HB.5x5 Hex Head Bolt 1/2-13 X 5 8 841 HB.5X6.5G8 Hex Head Bolt 1/2-13 X 6 1/2 Gr 8 2 242 HB.75x5G8 Hex Head Bolt 3/4-10 X 5 Gr 8 1 143 HB.75x6.5G8 Hex Head Bolt 3/4-10 X 6 1/2 Gr 8 3 344 HNY.75 Nylon Locknut .75" 1 145 LW.5 Lockwasher-1/2 4 446 PF208V Clevis Option-Perfect Hitch-1.25 Drawpin 1 147 PF237VR Perfect Hitch Base, Cat III 1 1

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-5

NDENDENDENDE

2

1

21

2

1

Tire and Hub Subassemblies

10039 HUB - 7500 LB, 1.5" OFFSET

ITEM PART DESCRIPTION 10039/QTY.

1 10139 Hub - 7500 LB (NoHardware)

1

2 10528 Stud Bolt WB46 .625- 18 UNF

8

3 10549 Inner Bearing 1

4 10550 Dust Cap 1

5 10551 Outer Bearing 1

6 10552 Seal 1

7 10553 Outer Race 1

8 10554 Inner Race 1

9 HNW.625 -18 Nut, Hex Wheel5/8-18 NF

8

Association Table

MODEL # 502 502 LP 552 552 LP 602 652 702 802 802 CE

Standard TIRE 13159 10607 13159 10607 13159 13159 13159 13159 10637

Standard HUB 10039 10039 10039 10039 10039 10039 14244 14244 10671

Optional TIRES 10626 AIRCRAFT TIRE and 14000 HD IMPLEMENT TIRE

13159 IMPLEMENT

ITEM PART DESCRIPTION

1 10040 I-222 15.0/55-17 16 ply

2 10038A Rim 16 x 10.5, 1.5 Offset - 8 Bolt Ag

10626 LOW PROFILE

ITEM PART DESCRIPTION

1 10626B Tire - Aircraft 11.5L x 14.5 - 28"

2 10626A Rim 14.5 x 9.5, 1.375 Offset - 8 Bolt Ag

14000 HD IMPLEMENT

ITEM PART DESCRIPTION

1 14000A

2 14000B Rim 17 x 15, .625 Offset - 8 Bolt Ag

14244 HUB - 1000 LB, 1.5" OFFSET

ITEM PART DESCRIPTION 14244/QTY.

1 14244A Hub - 10,000 LB (nohardware)

1

2 14442 Seal - 10,000 LB Hub 1

3 14443 Cup - Bearing, Inner 1

4 14444 Cup - Bearing, Outer 1

5 14445 Dust Cap - 10,000 LB Hub 1

6 14478 Cone - Bearing, Inner 1

7 14479 Cone - Bearing, Outer 1

8 14480 Bolt - Wheel, Press-In(5/8" x 2.25")

8

9 HNW.625 - 18 Nut, Hex Wheel 5/8-18NF

8

Assembly 10671 (Used only on model 802CE)

Parts List

Brake System Subassembly

ITEM PART DESCRIPTION QTY.

1 14879 Outer hub bearing 2

2 14880 Inner hub bearing 2

3 14881 Wheel Stud 16

4 14882 Hub/drum assembly 2

5 14883 Hub cap 2

6 14884 Split Pin 2

7 14885 Crown nut 2

8 14886 Wheel nut 16

9 14887 Retaining ring 2

10 14888 Shoe with lining 2

11 14889 Camshaft 2

12 14890 Brake lever 2

13 - Axle 1

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-6

NDENDENDENDE

8

17

13

10

16

9

7

15

5

6

3

14

12

1

2

11

18

Use Driveline14105 for 540 PTOUse 14104 for 1000 PTO.

4

2019

Assemblies 14104 & 14105 (Common on all machines)

Driveline Subassembly

ITEM PART DESCRIPTION 14104/QTY.

14105/QTY.

1 14510 Bearing Ring SC25 (not shown) 2 2

2 14516 Support Bearing (not shown) 1 1

3 14845 Spring Pin 10 x 80 (not shown) 2 2

4 14851 Inner Profile S4GA - 1

4 14870 Inner Profile S4GA 1 -

5 14852 Shield Cone 3 Rib 1 1

6 14853 Inboard Yoke S4 1 1

7 14854 Cross and Bearing Kit 1 1

8 14856 Cross and Bearing Kit 2 2

9 14859 Inboard Yoke S5 1 1

10 14862 Shield Cone 6 Rib 1 1

11 14863 Double Yoke 1 1

12 14864 Yoke 1-3/8 6 SPL ASG - 1

12 14865 Yoke 1 - 3/8 " 21 SPL. ASG 1 -

13 14866 Inn. Shield Tube Rnd. 1 -

13 14867 Inn. Shield Tube Rnd. - 1

14 14868 CV Cone & Bearing Assy. (notshown)

1 1

15 14869 Shearbolt Clutch - 1

15 14872 Shearbolt Clutch 1 -

16 14871 Profile & Sleeve W. A. 1 -

16 14874 Profile & Sleeve W. A. - 1

17 14873 Out. Shield Tube Oval 1 -

17 14875 Out. Shield Tube Oval - 1

18 14878 Safety Chain (not shown) 1 1

19 HB.313x2.5 Hex Head Bolt 5/16-18 X 2 1/2 1 1

20 TLN.313 Nut, Hex Top Lock 5/16-18 UNCGr 5 Zn Plt

1 1

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-7

NDENDENDENDE

5

2

8

4

3

6

1

(14134 - Driveline)

Driveline 14135 is used on all single speed machines.Driveline 14134 replaces 14135 when the two speedgear box option is installed.

(14135 - Driveline)

7

14134 & 14135 (Common on all machines)

Driveline Subassembly

ITEM PART DESCRIPTION 14134/QTY.

14135/QTY.

1 14845 Spring Pin 10 x 80 (not shown) 2 1

2 14848 Inner Profile S4 - 1

2 14858 Inner Profile S4 1 -

3 14849 Inboard Yoke S4 1 1

4 14850 Cross and Bearing Kit 2 -

4 14854 Cross and Bearing Kit - 1

5 14855 Yoke - 1 3/4 " - 20 SPL. I. C. 2 -

5 14860 Yoke 1-3/4 20 SPL ASG - 1

6 14859 Inboard Yoke S5 1 -

7 14861 ASG Col. Kit (not shown) - 1

8 14876 Outer Profile S5 1 -

8 14877 Stub Shaft & Outer Profile (S5) - 1

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-8

NDENDENDENDE

-8-

-6-

-1-

-4-

13 20

13 20

15

25

22

2325

22

23

-3-

16

25

14

22

17

18 24

11

27

12

26

9

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-9

NDENDENDENDE

14425 - Oil Tank5*

2

3

1

4

6 14425 - Parts List

ITEM PART DESCRIPTION QTY.

1 10088 Clamp - Hose, Spring Grip 1/2" 22 10405 Hydraulic Tank 13 10407 Cap - Breather, Oil Tank 14 CPUT.5x.375 Tube - Polyurethane, Clear 0.65 ft5* HFL90808 HF - 90 Elbow, #8 NPT Male x #8 JIC Male 16 HFW90606 HF - 90 Elbow, #6 NPT Male x #6 Hose Barb 2

Assemblies 14425, 10143, 10703 & 10805 (Common on all machines)

* Item ( 5* ) on the Tank is connected to either one of Items ( 13, 14 or 15 ) on the Gearboxes via the " Gearbox " hose shown on Page 3-7.

Oil Tank & Gearbox Subassemblies

Association TableMODEL # 502 502 LP 552 552 LP 602 652 702 802PART #(standard) 10143 10143 10703 &

1080510703 &10805 10143 10703 &

10805 14923 14923

OPTIONAL 10143 is a 540 RPM Gearbox and 10703 & 10805 combined make a 1000 RPM Unit.It is an option to convert any machine to either a 540 or 1000 RPM.

Planetary Gearbox AssembliesITEM PART DESCRIPTION 14923

/QTY.14996/QTY.

10143/QTY.

10703/QTY.

10805/QTY.

-1- 10143L Gear Box - - 1 - -

2 10480 Gear Box Oil - Shell Tivela Oil WB(407 521 30) - - 15.75 L 6.5 L 2 L

-3- 10805L Gearbox - (1000RPM) - - - - 1-4- 13703L Planetary PG1802 VM21.4 - - - 1 -

5 14035 Grease - Elbidea Brg (LCEP2) 1 1 - - --6- 14923L RR1750 Single input 1 - - - -

7 14949 Gear Box Oil - Shell Omala HD -220Oil 17 L 17 L - - -

-8- 14996L RR1700 Single (154F5026) - 1 - - -11 CT.25x.030 Copper Tubing - 1/4OD x .03W 1 1 1 1 -12 GZ.125N Grease Zerk -1/8-27 NPT Straight 1 1 1 1 -

13 HFAS#8NM#8NF Hyd Fit Adapt Swivel, #8 NPT Male x# 8 NPT Female 1 1 - - -

14 HFM40607 HF - Straight, #6 NPT Male x #6 NPTFemale Swivel - - - 1 -

15 HFM90807 HF - 90 Elbow, #8 NPT M x #6 NPTSwiv F - - 1 - -

16 HFM90809 HF - 90 Elbow, #8 NPT M x #8 NPTSwiv F - - - - 1

17 HFN00606 Nipple-Hex 3/8 NPT - - 1 1 -18 HFN00707 Hyd Fitting-Union-3/8 NPT Female X2 - - 1 1 -19 HFN01207 HF Bushing #12NPT M x #6 NPT F 1 1 - - -20 HFN01209 HF Bushing #12NPT M x #8 NPT F 1 1 - - -

21 HFN900404CSN HF- 90 Elbow, #2 NPT M x #4 CompSleeve for 1/4 OD Pipe 1 1 - - -

22 HFN90607 HF - 90 Elbow, #6 NPT Male x #6NPT Female 1 1 1 1 -

23 HFNH12 HF #12 NPT Hex Plug 1 1 - - -24 HFNV06 HF - Vent Plug, #6 NPT - - 1 1 -25 HFNV08 HF - Vent Plug, 1/2" NPT 1 1 - - 1

26 HFY00305 #2 NPTf x #4 Comp Sleeve 1 1 1 1 -

27 HFY90205 HF- 90 Elbow, #2 NPT M x #4 CompSleeve for 1/4 OD Pipe - - 1 1 -

Gearbox Subassemblies - Parts List

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-10

NDENDENDENDE

(10001 - Auger)

6

5

2**

5

3***

1*

4

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-11

NDENDENDENDE

Assemblies 10001, 10220 & 14168

Auger Subassembly

ITEM PART DESCRIPTION 10001/QTY.

10220/QTY.

14168/QTY

1* 10008A Knife Reinforcement Plate 1 1 12** 10008 Auger Cutting Knife 9 9 93*** 10009 Scraper 1 1 1

4 10181 Weldment - Auger 1 - -4 10337 Weldment - Auger - 1 -4 14167 Auger Weldment - - 15 BFHS.625X2 Hx Sckt Flt Hd Bolt 5/8-11 NC x 2 Gr 8 (C'Sunk 82 deg) 35 35 356 BFHS.625X2.5 Hx Sckt Flt Hd Bolt 5/8-11 NC x 2 1/2 Gr 8 (C'Sunk 82 deg) 4 4 4

MODEL # 502 502 LP 552 552 LP 602 652 702 802 802 CE

AUGER PART # 10001 10001 10220 10220 10001 10220 14168 14168 14168

10001, 10220 &14168

Associativity Table

Parts List (For standard 9 Knife Augers)

Any combination and number of knives is possible up to a maxuimumof nine knives. The Table below contains the predetermined Kits.

** Optional Knife Kits

*** Optional Scrapers

Several Reinforcement Plates may be installed.* Optional -

Auger Subassembly - Parts List

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-12

NDENDENDENDE

PART KNIFE OR KNIFE KITS PART KNIFE OR KNIFE KITS

10413 Single Steel Knife (inquire) 7 Steel Knives Kit

10008 Single Carbide Knife (inquire) 7 Carbide Knives Kit

(inquire) 5 Steel Knives Kit (inquire) 9 Steel Knives Kit

(inquire) 5 Carbide Knives Kit (inquire) 9 Carbide Knives Kit

PART SCRAPERS PART SCRAPERS

10009 3 1/2" Scraper 10009B 5 1/2" Scraper

10009F 4" Scraper 10009E 6" Scraper

10009A 4 1/2" Scraper 10009C 6 1/2" Scraper

10009D 5" Scraper

Assemblies 10386, 10387, 10388 & 10791 (Common to all machines)

1

18

4

15

102

13

7

5

8

9

17

3

14

6

(10388 - 7' Incline Conveyor)

16

11

Conveyor Subassembly

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-13

NDENDENDENDE

12

Conveyor Parts List

ITEM PART DESCRIPTION 10386/QTY.

10387/QTY.

10388/QTY.

10791/QTY.

1 10091 Motor Guard Cover Plate 1 1 1 1

2 10098 Hyd. Motor - Conveyor 1 1 1 1

3 10100 Flange Bearing, Radial Ball Bearing 4 4 4 4

4 10163 Coupling Half - 1 in. Bore 1 1 1 1

5 10165 WA - Chain Guard, LH 7.5 ft - - - 1

5 10476 WA - Chain Guard, LH 6 ft 1 - - -

5 10476A WA - Chain Guard, LH 7 ft - - 1 -

5 10876 WA - Chain Guard, LH 6.5 ft - 1 - -

6 10166 Coupler Chain - Double 1 1 1 1

7 10168 WA-Chain Guard 7.5 ft, RH - - - 1

7 10475 WA-Chain Guard 6 ft, RH 1 - - -

7 10475A WA-Chain Guard 7 ft, RH - - 1 -

7 10875 WA-Chain Guard 6.5 ft, RH - 1 - -

8 10375 WA-Conveyor 6-1/2 ft. - 1 - -

8 10376 WA-Conveyor, 6 ft. 1 - - -

8 10377 WA-Conveyor 7 ft. - - 1 -

8 10790 WA-Conveyor 7-1/2 ft. - - - 1

9 10385 Assy - Conveyor Idle Shaft 1 1 1 1

10 10470 Coupling Half - 1-1/4 Bore 1 1 1 1

11 10666 WA - Btm Sheet, Conveyor 6 ft. 1 - - -

11 10667 WA-Btm Sheet, Conveyor 6.5 ft. - 1 - -

11 10668 WA - Btm Sheet, Conveyor 7 ft. - - 1 -

11 10889 WA-Btm Sheet, Conveyor 7.5 ft. - - - 1

12 10760 WA - Conveyor Chain 6' 1 - - -

12 10843 WA - Conveyor Chain 6.5' - 1 - -

12 10845 WA - Conveyor Chain 7' - - 1 -

12 10846 WA - Conveyor Chain 7.5' - - - 1

13 10796 WA - Guard, Hyd Motor 1 1 1 1

14 10979 Plate - Chain Tensioner 2 2 2 2

15 12378 Key - 1/4x1/4x1.25 in 1 1 1 1

16 HBFT.5x4 Hex Head Bolt 1/2-13 X 4 Full Thread 2 2 2 2

17 HN.5 Hex Nut 1/2-13 UNC 4 4 4 4

18 WK.25x1.00 Woodruff Key, 1/4 x 1.00 Dia. 1 1 1 1

CONVEYOR PART # 10386 10387 10388 10791

CONVEYOR SIZE 6' 6.5' 7' 7.5'

OPTIONAL All conveyors fit on all machines

10386, 10387, 10388 & 10791 (Common on all machines)

Association Table

Conveyor Subassembly - Parts List

New Direction Equipment14153A - Version 2

Models 502-802 - Vertical Cutter/Mixer/Feeder 2-14

NDENDENDENDE