Date post: | 01-Dec-2015 |
Category: |
Documents |
Upload: | salman-shaikh |
View: | 43 times |
Download: | 3 times |
New Warranty Management ApplicationUsers Guide
Service ‐Technical
Table of Contents1. Recommended browser for best & speedy performance 3
2. Login in DMS for complete list of job cards 8
3. Query the job card to get detail 14
4. Create warranty claim 16
5. Create bundle list of associate claims 21
6. Pull the DMS bundle no. to BIZ 27
7. Validate and proceed DMS claims into BIZ 31
8. Check error log of DMS claims while pulling into BIZ (if any) 34
9. Disassociate the error claims in DMS 36
10. Create packing list 39
11. Go to invoice printing and take print of part and service tax invoice 46
12. Claims Submission 51
13. General Do’s and Don’ts 55
2
Service ‐Technical
Recommended browser for best & speedy performance
Recommended browser for using online warranty application on hermotocorp.biz is Internet explorer 6 or 7 for best & speedy performance.
Following settings are required in case of using internet explorer version: 6 or 7
If you receive following message:
3
1
Service ‐Technical
You must have the following setting in place:
Step1 ‐ Please click on to "Tools" in Menu Bar of Internet explorer and click "Pop‐up Blocker” then select "Pop‐up Blocker Settings", as shown below:
4
Service ‐Technical
Step 2 ‐ Enter "www.heromotocorp.biz" in the text field and click on "Add" button then close the screen, as shown below:
5
In case “Pop‐up blocker Settings” option isdisable then click on “Turn On Pop‐upBlocker”. Then proceed again as mentionedabove:
Service ‐Technical
Following settings are required in case using internet explorer version: 8 or higher If you receive following message:
6
It means you are using internet explorer version 8 or higher, and you must have the following setting in place:
Step1 ‐ Please click on "Tools" inMenu Bar of Internet explorerand click "Compatibility ViewSettings", as shown :
Service ‐Technical
Step 2 ‐ Enter "www.heromotocorp.biz" in the text field and click on "Add" button, as shown below:
7
Service ‐Technical
Login in DMS
8
Login in DMS with your user id & password
2
Service ‐Technical
Navigation
9
You can create the claims by going througha) Service Screen – By searching JC number against which parts were issued
under warrantyb) Use My Dash Board Report to get the details of unclaimed warranty parts Job
Card wise
Service ‐Technical
Login “My Dash Board”, go to service warranty reports for the unclaimed warranty parts
10
Drill down on dealer name
Service ‐Technical
Complete list of all the job cards where warranty part is issued but claim are yet to be created will be displayed
11
Service ‐Technical
Download the report in excel format
12
Service ‐Technical
Download the report in excel format
13
Service ‐Technical
Query the Job Card
14
Query the job card (based on the earlier downloaded report) against which parts are issued under the warranty
3
Service ‐Technical
Drill down on the Job card form applet
15
Service ‐Technical
Create the warranty claimSelect the parts for which claim needs to be created
16
4
Service ‐Technical
Select the type of claim
17
Service ‐Technical
Fill the details in claims
18
Fill the required details like Malfunction kms, Symptoms details, Replacement code
Service ‐Technical
Save the claim
19
Service ‐Technical
Check if claim completed flag is ‘On’
20
Service ‐Technical
Create bundle list of associate claimsNavigate the claims >> DMS Claims Bundle
21
5
Service ‐Technical
Select type of packing list
22
Service ‐Technical
Click on the associate claims on the child applet against the packing list
23
Service ‐Technical
Click on the claims that you want to associate & click on ‘Associate’
24
Service ‐Technical
After associating, Click on ‘OK’
25
Service ‐Technical
Check the claims & line items in child applet for re‐verification
26
Service ‐Technical
Pull the DMS bundle no. to BIZCopy the DMS packing list no. & proceed for heromotocorp.biz process
27
6
Service ‐Technical
Login on heromotocorp.biz
28
Service ‐Technical
Navigate to Warranty Claim Entry Vehicles view & then drill down on Pull
DMS Claims link
29
Service ‐Technical
Copy & Paste the DMS packing list number & press Proceed
30
Service ‐Technical
Validate and proceed DMS claims into BIZ
31
7
Service ‐Technical
If there is no error all the selected claims will turn green & press proceed
32
Service ‐Technical
The final creation message as per below details will be populated
33
Service ‐Technical
Check error log of DMS claims while pulling into BIZIf there are any error then download the error log for claim wise error details
34
8
Service ‐Technical
Sample error log
35
Log a ticket with help desk for all the error claims & required correction
Service ‐Technical
Disassociate the error claims in DMS After disassociating the error claims in DMS pull the bundle list again into the BIZ. For further steps continue from slide no 39.
36
Disassociate as per error log
9
Service ‐Technical
The packing list status would be changed after 1 hour (user must verify the same)
37
Service ‐Technical
Also check the status of associated claims it must change to “Submit to Warranty”
38
Service ‐Technical
Create packing list
39
Packing List screen Usage Procedure: Once the Claim is created, Packing List needs to be created for packing warranty parts. Pack the warranty material as per packing list. Please click‐on under navigation menu on LHS
10
Service ‐Technical 40
1. Select Date from claim selection for packing list option: On selecting, the date all the non‐submitted claims will be displayed prepared till selected date. 2. Select Recommendation type: N‐Normal or G‐Recommendation. 3. Press Packing List button to continue. On submit Next screen:
Service ‐Technical 41
For viewing parts claimed in the claim form press the desire sap claim number link.
Service ‐Technical 42
Select the claims using select box with tick mark for including claim in the packing list.
Press “Save” button to continue; Popup message displayed for User confirmation.
Press YES to continue. Next screen will be displayed as:
Service ‐Technical 43
Press link: Download To PDF, User will get popup message for saving packing list in PDF format.
Service ‐Technical
Press Save button to save packing list at desired location. By default file will save in Desktop.
Service ‐Technical 45
Sample packing list format:
Service ‐Technical
Go to Invoice Printing and take print of Part & Service Tax invoice
46
The Dealer has to take print‐out of the Part Invoice and Service Tax Invoice.Dealer has to go to “Invoice Printing” link to take the print‐out.
11
Service ‐Technical 47
Click on the F4 help of the Packing List Number to open following screen.
Service ‐Technical
Select the Packing List Reference No or Part Invoice No. or Service Tax Invoice No. The following screen will open.
Service ‐Technical 49
Now click on “Print Part Invoice” to print Part Invoice and click on “Print Service Tax Invoice” to print Service Tax Invoice. The sample formats of print‐out will be as follows:
Part Invoice
Service ‐Technical 50
Service Tax Invoice
Note – For recommended category the claims would be routed to concern TSM for approval & there after be submitted to HMCL.
Service ‐Technical
Claim Submission
51
Once the Packing list is created & material dispatched to HMCL, then claims need to be submit to HMCL.For submitting warranty claim use the highlighted Link:
12
Service ‐Technical 52
1. Select the claim type: N‐Normal or G‐Recommendation. Press “Submit” button to continue. In case of Recommendation Claims Approved by TMS will only be populated in the Reference No. drop‐down.2. In the next screen reference number will be asked from the user. Select reference number using drop down button.
Service ‐Technical 53
After selecting reference number press “Submit” button to continue. System will ask for user confirmation:
Press “YES” to continue. In the next screen Material booking detail will be asked from the user.
Press “Save” button to submit the claims; system will ask for user confirmation:
Service ‐Technical 54
Press “YES” button for submitting warranty Claims to HMCL. On successful submission message display as: “Data Saved Successfully”
Service ‐Technical
General Do’s and Don’ts
55
Do’s
1. If you encounter any issues related to login, please contact HMCL support team 2. Keep minimum number of sessions open 3. Search for data for period of maximum one month only at a time to get better
performance.
Don’t
1. Do not execute any report with longer duration of more than month. This hampers the system performance.
2. Do not close the browser for logoff, instead Use Logoff link. 3. Do not keep the system idle for long time
13
Service ‐Technical 56
Hero MotoCorp Ltd.
Head Office34, Community Centre, Basant Lok,Vasant Vihar, New Delhi – 110057.Tel: 91‐11‐46044100, 26143198Fax: 26143321, 26143198
Hero MotoCorp Ltd.
Warranty Management Section(Service‐Technical)37th K.M. Stone, Delhi – Jaipur Highway, Sector – 33, Gurgaon‐ 122 001 Haryana ‐ India Email: [email protected] Phone: 01242895789‐794.