Next generation tank coatings: reducing opex, saving lives13 September 2021 • 14:00-15:30 BST
#tankers
Part ofTanker Shipping
& Trade Tech & Ops Webinar Day
13 September 2021
Supporting organisationSponsored by
Presentation & sponsor documents:Page 2: Captain Onur Yildirim, Advanced Polymer CoatingsPage 12: Guy Johnson, L&I Maritime (UK) LtdPage 44: D. Terry Greenfield, CONSULEX / Past Chairman AMPP (Formerly NACE International) 2020-2022Page 49: Advanced Polymer Coatings company information
Thank you for the opportunity to meet!
Captain Onur YildirimGlobal Marine Manager,
Advanced Polymer Coatings
1
Can a tank coating be ‘green’ & save on Operational Cost?
2
What constitutes a Cargo Tank Coating to be ‘Green’, and to be beneficial for ‘OPEX’
Coating’s Properties
3
Cleaning Efficiency Turnaround Time
Recovery
Absorption
Desorption
What is Important and What to look for as Operator?
Coating’s Properties
4
High Absorption
Low DesorptionLong Recovery
High Absorption
High DesorptionRelatively shorter
Recovery
Virtually
Non-AbsorptionNon-Recovery
• Cross-Contamination• Longer Cleaning Period & Increased Slop• Slow Turnaround• Increased Fuel Consumption• Increased Chemical Cleaner Consumption
What is Important and What to look for as Operator?
Better Technology: Higher Cross -Linking
Microscopic coatingsurface images
High Functionality Polymer
Versus
Phenol Novolac Epoxy
x250 Magnification
x1000 Magnification
x250 Magnification
x1000 Magnification
Phenol Novolac EpoxyHigh Functionality Polymer
(Higher Cross-Linking)
5
Impermeable line of defense and easy to clean low energy & smooth surface
Comparison of Microscopic Coating Surface Images from Tubitak – The Scientific and Technological Research Council of Turkey, in Ankara, Turkey
Quantifying Savings
6
Reduction of Fuel Cost by 3%
• 3% fuel savings will generate operating cost savings of $600,000 to$1,200,000 per annum per tanker
• Annual fuel cost per ship ranges from$20,000,000 to $40,000,000 per annum
• Fleet size of (10) ships could achieve savings of $6,000,000 to $12,000,000 per annum
Fuel savings due to less tank cleaning
Source: Dr.Z. Bazari, Overview of ship energy management seminar
Quantifying Savings
7
• Fuel consumption per typical tanker 40,000to 50,000 MT per annum
• Average carbon content of marine fuels isabout 86%
• CO2 production per ship: 140,000 to 160,000MT per year
• 3% fuel saving = CO2 reduction of 4,500 MTper annum per ship
• 10 ship fleet equates 45,000 MT per annumof CO2 reduction
Source: Dr.Z. Bazari, Overview of ship energy management seminar
Reduced emissions due to less tank cleaning
Quantifying Savings
8
Source: Guy Johnson, Director, L&I Maritime, U.K. ‘Effects on your bottom line’
Reduced emissions due to less tank cleaning
• High Functionality Polymer coated vesselproduces 78.5% less CO2 emissions comparedto the zinc coated vessel for the same tankcleaning operation.
Zinc Coated Vessel
• 56 hours of hot water washing produces 106.4MT of CO2
High Functionality Polymer Coated Vessel
• 12 hours of hot water washing produces 22.8MT of CO2
Quantifying Savings
9
• A vessel “costs” $18,000 per day• A vessel has 16 cargo tanks.• 4 cargo tanks can be cleaned simultaneously.• Each cargo tank requires 200L of cleaning chemical(s) (where cleaning chemicals are required).• The typical cost of a regular cleaning chemical is $3 per litre
Zinc Coated Vessel High Functionality PolymerCoated Vessel
Total Cleaning Time 64 hours 16 hours
Hot Water Cleaning Time 56 hours 12 hours
Cleaning Chemical Consumption 3200L 0L
• The financial advantages of a High Functionality Polymer versus zinc silicate in this example can bequantified as follows:
Total time saving 48 hrs = $36,000Cleaning chemical saving 3200L = $9,600Hot water washing saving 44 hrs = 26.4MT of fuel**
(** On average a vessel consumes 0.6MT per hour of HFO / MGO in the boiler and A/E during tank cleaning).
Source: Guy Johnson, Director, L&I Maritime, U.K. ‘Effects on your bottom line’
Let’s assume the following…
Thank You
10
Questions?
How Clean is Clean?L&I
L&I Maritime (UK) LtdHall Farm Offices
West Markham
Newark
Nottinghamshire
NG22 0GU
UNITED KINGDOM
Tel: +44 (0) 1777 232 253
L&I
How Clean is Clean?L&I
• What makes a cargo tank clean, or not?
• The first point to consider is that the efficiency of all tank cleaning operations is determined by some kind of inspection
Visual
Wall Wash
How Clean is Clean?L&I
• Visually clean is fairly self explanatory
✓ CDOF – Clean Dry Odour Free
• But “wall wash” standard is less straightforward because there is no universal specification
✓ How Clean is Clean?
How Clean is Clean?L&I
• And who decides the wall wash specifications and what are they?
• Charterers and / or cargo Interests
How Clean is Clean?L&I
Dear Guy
Good day sir,
I have one question about WWT criteria.We would like to carry cargo of naphtha which product of GS Caltex Yeosu.For this cargo, charterer informed WWT requirement as bellows;--------------------------------------------------------------------------------------------------------------OWNERS CONFIRM VESSEL/MASTER WILL COMPLY WITH BELOW WALL WAST TEST CRITERIA PRIOR LOADING- APPEARANCE-VISUAL-PASS-CLEAR AND FREE OF SUSPENDED WATER- HYDROCARBONS – 125 PPM MAX- CHLORIDE – 0.5 PPM MAX- WATER MISCIBILITY – SPEC/RESULT : COMPLETE- NONVOLATILE MATTER – SPEC MAX 5 PPM GC- PT - CO COLOR METHOD D5386 MX 15- NITROGEN 1 MAX ASTM D6069- PERMANGANATE TIME TEST – MIN 30 MIN @ 15 DC
How Clean is Clean?L&I
Dear Julie,
Charterers have advised zero chlorides, I just asked them to reconfirm same and they replied;
That's correct. Zero.
Best regardsAsle JohansenITC / International Tanker Chartering AS
Phone : +47 55 90 28 00Direct : +47 55 90 28 06Mobile : +47 40 08 22 60
How Clean is Clean?L&I
What is the wall wash?L&I
• It is supposed to provide information to indicate whether a cargo tank is “clean” or not
• But what does it actually tell us?
How Clean is Clean?L&I
How Clean is Clean?L&I
How Clean is Clean?L&I
• Really only that the bottom 2 – 3M of the cargo tank is clean. Approximately 1% of the internal surface area of the tank?
• What about the remaining 99%?
• It is an “unknown” ..
How Clean is Clean?L&I
• And then we have to ask the most important question ..
• What are the wall wash specifications? How clean is clean?
• Blank canvas / no limitations for commercial interests
How Clean is Clean?L&I
• To one charterer a colour of 10 is acceptable, to others it is “dirty”
How Clean is Clean?L&I
• An inorganic chloride level higher than 0.5ppm is apparently evidence of “poor” tank cleaning.
• Really? 1 second in 23 days …
How Clean is Clean?L&I
• If a vessel does not pass the wall wash, it cannot load the next cargo
• Even though it represents less than 1% of the internal surface area of the cargo tank and perhaps more importantly none of the cargo lines.
How Clean is Clean?L&I
But if as much as 99% of the cargo tank is potentially un-clean at the start of cargo operations ..
Why do we not see more off-specification cargoes?
How Clean is Clean?L&I
• DILUTION EFFECTS
• Or .. what happens to the contaminants found in the wall wash sample when the tank is fully loaded
• Typically 3000 times dilution
How Clean is Clean?L&I
How Clean is Clean?L&I
• Wall wash inspections are imposed for one reason:
• To provide reassurance to cargo interests that any particular cargo tank is suitable to load the next nominated cargo
• But this is just not possible.
• All they do is contribute to unnecessary CSE and overcleaning (GHG emissions)
How Clean is Clean?L&I
• Each hour of hot water washing, consumes on average 0.6MT per hour of HFO / MGO in the boiler and A/E
• Burning 1MT of HFO produces approximately 3.2MT of CO2
• Meaning each hour of hot water washing liberates1.9MT of CO2 into the atmosphere
How Clean is Clean?L&I
• The dilution effect “allows” us to load chemical cargoes without them becoming contaminated.
• Not the wall wash specification.
• Focus on main area of concern, using techniques such as UV spectroscopy
How Clean is Clean?L&I
• Emerging trend for received cargoes to be tested for extremely low levels of previous cargo. WHY?
• Capability, bargaining tool and no faith in the wall wash.
• But what impact does this have on tank cleaning?
• And what about the influence of the cargo tank lining?
How Clean is Clean?L&I
• Stainless steel. Organic Coating. Inorganic Coating.
• If the coating / lining absorbs previous cargo residues, this needs to be recognised and understood. WHY?
• The wall wash generally does not pick these residues up. Contact time.
• Do not pretend that a “good” wall wash result means the cargo tank is suitable
How Clean is Clean?L&I
How Clean is Clean?L&I
How Clean is Clean?L&I
• Lab based project.
• Test panels immersed in different cargoes, cleaned until the wall wash passed, before being immersed in methanol.
• The methanol was tested for the presence of the previous cargo
L&I
0.0
5.0
10.0
15.0
20.0
25.0
30.0
premium epoxy phenolic zinc
gasoline in methanol (mg/kg)
gasoline inmethanol (mg/kg)
L&I
0.0
2.0
4.0
6.0
8.0
10.0
premium epoxy phenolic zinc
ulsd in methanol (mg/kg)
ulsd in methanol(mg/kg)
L&I
0.0
5.0
10.0
15.0
20.0
25.0
30.0
35.0
40.0
45.0
premium epoxy phenolic zinc
styrene monomer in methanol (mg/kg)
styrene monomerin methanol(mg/kg)
31
L&I
• Coatings that actively absorb certain cargo types should not be loaded directly afterwards with cargoes that are sensitive to the previous cargo.
• Commercial interests need to understand this as well.
• If the next cargo is high purity, choose a coating with a good prior cargo history, or a premium coating or stainless steel.
• Do not hide behind the wall wash
• Do not gamble safety/sustainability against cargo quality
Questions? L&I
No Magic Solution for Life-Cycle Longevity
D. TERRY GREENFIELD
P R I N C I PA L C O N S U LTA N T, C O N S U L E X
No Magic Solutions ▪ Its all in the process!
Life-Cycle Success
Material Selection
Installtion/Application
Integration of “Lessons
Learned”
Life Cycle Considerations and
Cost
Barriers to Extended Life-Cycle▪ Initial Costs vs. Life-Cycle Costs
▪ Initial Installation
▪ Inspection
▪ Initial Repairs
▪ Maintenance
Closing Thoughts Extended Life-Cycle is achievable
Success is in the process and isn’t magic!
Thanks!
The industry leading cargo tank coating for
chemical & product tankers, with superior chemical resistance.
Key Coatings Benefits
There's Only 1 MarineLINE®
3 Years 4 Years
5 Years 6 Years
11 Years
MarineLINE® cargo tank coating system offers long service lifepotential. See these photos of tanks at various inspection intervals.
For chemical and product carriers Strong Return on Investment (ROI) Virtually non-permeable for assurance of product purity Faster, easier cleaning and venting Maximum versatility to carry acids, alkalis, solvents, CPPs, PFADs, Bio-Fuels, and Methanol Excellent flex stressing GRAS - Generally recognized as safe for food grade cargoes FDA compliant Superior chemical resistance compared to stainless steel, phenolic epoxies, and zinc silicate coatings Field repairable Superior bond strength and adhesion Resistance to wear, abrasion, and impact Very low VOC - 130 grams/L (1.09 lbs./gal) Thermal shock resistance -40°C to +150°C (-40°F to +302°F ) ABS ISO 9001:2015 Certification Third party warranty through Helvetia Group, covering shipowners and operators for a specified warranty period up to 5 years.
Go Green:Easier Tank Cleaning Produces Additional Return On Investment (ROI)
Glossy, smooth surface Virtually non-absorbent lining Reduces cleaning time Reduces chemical cleaning use Reduces slops Reduces fuel burning (to heat hot water/steam) A wide range of approved cleaning detergents
and chemicals can be used for next cargoes Substantial savings in CO2, SOx, and NOx
reductions per voyage:• Tens of thousands of $USD savings
in bunker fuel• Tens of tons of SOx and NOx reductions• Hundreds of tons of CO2 reductions
MarineLINE® When Performance CountsGreater Versatility When Switching CargoesThese charts show how easily you can switch cargoes to take advantage of the greatest amount of sequencing possibilities and the opportunity to carry the most profitable
cargoes.
Why MarineLINE® Is BetterPatented Polymer Technology Delivers Results: Microscopic Crosslink Density
Phenol Novolac Epoxy MarineLINE®
x250 Magnification x250 Magnification
x1000 Magnification x1000 Magnification
Microscopic coating surface images taken at TUBITAK, in Ankara, Turkey, compare the differences of the APC's MarineLINE® versus standard Phenol Novolac epoxy coatings.
(LEFT) a Phenol Novolac Epoxy coating at various magnifications, compared to (RIGHT) the MarineLINE® cargo tank coating system.
Higher crosslinking leads to a denser structure that enhances high chemical and high temperature resistance.
The information provided by Advanced Polymer Coatings, Inc. (APC) for the application or repair of APC coatings is based upon protective coating industry standards and knowledge gained through observation of professional applicators throughout the world that have successfully applied APC coatings. APC does not exercise any control over selection of the applicator that applies or repairs APC coatings. By providing information APC is not representing, directly or by implication, that an applicator that is provided with this information will achieve a result that will pass without objection in the trade or industry, otherwise referred to as MERCHANTABILITY, or will meet the vessel owner’s protective coating requirements, otherwise referred to as FITNESS FOR A PARTICULAR PURPOSE. The only warranty provided by APC through its information and literature is that all APC products when delivered will have been manufactured in accordance with APC’s manufacturing procedures, will be accurately labeled, and when mixed, applied and cured in a controlled environment in accordance with APC’s current written application guidelines will withstand chemical corrosion as set forth in APC’s chemical compatibility reference
guide. The chemical compatibility reference guide and current application guidelines are available at www.adv-polymer.com. Any customer specific express warranty can only arise from a written warranty extended by APC to the specific customer identified in the writing. APC DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THAT ARE CONTAINED IN ARTICLE 2 OF THE UNITED STATES UNIFORM COMMERCIAL CODE AND ANY SIMILAR WARRANTIES CONTAINED IN THE LAWS OF OTHER COUNTRIES WHERE APC PRODUCTS ARE DELIVERED OR APPLIED. ALL CONTRACTS FOR THE SALE OF APC PRODUCTS SHALL BE GOVERNED BY THE UNIFORM COMMERCIAL CODE WITHOUT REGARD TO ANY STATE VARIATIONS.
© Copyright 2020-03-20 APC2017
Advanced Polymer Coatings Avon, Ohio 44011 U.S.A. +1 440-937-6218 Phone+1 440-937-5046 Fax800-334-7193 Toll-Free USA & Canada
www.adv-polymer.com
T O M O R R O W ’ S S O L U T I O N S T O D AY