Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 1
Ni-Alubronze
Valves
A
N
S
I
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 2
INDEX VALVE TYPE
GATE
GATE
GATE
GATE
GATE
GATE
GATE
GLOBE
GLOBE
GLOBE
GLOBE
GLOBE
GLOBE
CHECK (SWING)
CHECK (SWING)
CHECK (SWING)
CHECK (SWING)
CHECK (SWING)
CHECK (LIFT)
CHECK (DUO)
CHECK (DUO)
CHECK (DUO)
BALL
BALL
BALL
BALL
BALL
BALL
BALL
BUTTERFLY
BUTTERFLY
BUTTERFLY
BUTTERFLY
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
BUTTERFLY (HP)
ENDS
Threaded
Threaded
Flanged
Flanged
Flanged
Flanged
Flanged
Threaded
Threaded
Flanged
Flanged
Flanged
Flanged
Threaded
Threaded
Flanged
Flanged
Flanged
Flanged
Wafer
Lug
Flanged
Threaded
Threaded
Threaded
Flanged
Flanged
Flanged
Flanged
Wafer
Semi-Lug
Lug
Flanged
Wafer
Wafer
Wafer
Wafer
Semi-Lug
Semi-Lug
Semi-Lug
Semi-Lug
Lug
Lug
Lug
Lug
Flanged
Flanged
Flanged
Flanged
PAGE
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
26
27
28
29
30
31
32
33
34
35
36
36
36
36
37
37
37
37
38
38
38
38
39
39
39
39
CLASS
150#
300#
150#
300#
150#
150#
300#
150#
300#
150#
300#
150#
300#
150#
300#
150#
150#
300#
150#
150#
150#
150#
300#
300#
150#
150#
300#
150#
300#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
150#
A
N
S
I
CONSTRUCTION
ISRS, Union Bonnet
ISRS, Union Bonnet
ISRS, Union Bonnet
ISRS, Union Bonnet
ISRS, Bolted Bonnet, PI
OS&Y, Bolted Bonnet
OS&Y, Bolted Bonnet
ISRS, Union Bonnet
ISRS, Union Bonnet
ISRS, Union Bonnet
ISRS, Union Bonnet
OS&Y, Bolted Bonnet
OS&Y, Bolted Bonnet
Y-type, Screwed Bonnet
Y-type, Screwed Bonnet
Screwed Bonnet
Bolted Bonnet
Bolted Bonnet
Union Bonnet
Dual Disc
Dual Disc
Dual Disc
Full Bore, Split Body
Reduced Bore, Split Body
Full Bore, 3-Piece Body
Reduced Bore, Split Body
Reduced Bore, Split Body
Full Bore, Split Body
Full Bore, Split Body
Replaceable Liner
Replaceable Liner
Replaceable Liner
Replaceable Liner
PTFE Seat
Fire Safe Seat
Metal Seat
Rubber Seat
PTFE Seat
Fire Safe Seat
Metal Seat
Rubber Seat
PTFE Seat
Fire Safe Seat
Metal Seat
Rubber Seat
PTFE Seat
Fire Safe Seat
Metal Seat
Rubber Seat
FIGURE
1400-C958
1401-C958
1850 UB-C958
1851 UB-C958
1840-C958
1850-C958
1851-C958
1410-C958
1411-C958
1820 UB-C958
1821 UB-C958
1820-C958
1821-C958
1430-C958
1431-C958
1810 SB-C958
1810-C958
1811-C958
1450 UB-C958
2238-C958
2238 LUG-C958
2238 FL-C958
1608-C958
1608 RB-C958
7480-C958
7235 RB-C958
7236 RB-C958
7235-C958
7236-C958
CWR-C958
CSR-C958
CLR-C958
CFR-C958
HWT-C958
FHW-C958
MHW-C958
HWR-C958
HST-C958
FHS-C958
MHS-C958
HSR-C958
HLT-C958
FHL-C958
MHL-C958
HLR-C958
HFT-C958
FHF-C958
MHF-C958
HFR-C958
SIZES
½”-3”
½”-3”
½”-3”
½”-1 ½”
2”-12”
2”-24”
2”-24”
½”-3”
½”-3”
½”-1 ½”
½”-1 ½”
2”-16”
2”-14”
½”-3”
½”-2”
½”-1 ½”
2”-24”
2”-24”
½”-1 ½”
2”-24”
2”-24”
2”-24”
½”-1 ½”
½”-3”
⅜”-2”
½”-24”
½”-24”
½”-24”
½”-24”
2”-20”
2”-48”
2”-48”
2”-160”
2”-10”
2”-10”
2”-10”
2”-10”
2”-60”
2”-60”
2”-60”
2”-60”
2”-60”
2”-60”
2”-60”
2”-60”
2”-60”
2”-60”
2”-60”
2”-60”
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 3
FIGURE NUMBER INDEX
FIG.
CFR-C958
CLR-C958
CSR-C958
CWR-C958
FHF-C958
FHL-C958
FHS-C958
FHW-C958
HFR-C958
HFT-C958
HLR-C958
HLT-C958
HSR-C958
HST-C958
HWR-C958
HWT-C958
MHF-C958
MHL-C958
MHS-C958
MHW-C958
1400-C958
1401-C958
1410-C958
1411-C958
1430-C958
1431-C958
1450 UB-C958
1608-C958
1608 RB-C958
1810-C958
1810 SB-C958
1811-C958
1820-C958
1820 UB-C958
1821-C958
1821 UB-C958
1840-C958
1850-C958
1850 UB-C958
1851-C958
1851 UB-C958
2238-C958
2238 FL-C958
2238 LUG-C958
7235-C958
7235 RB-C958
7236-C958
7236 RB-C958
7480-C958
PAGE
35
34
33
32
39
38
37
36
39
39
38
38
37
37
36
36
39
38
37
36
4
5
11
12
17
18
22
26
26
20
19
21
15
13
16
14
8
9
6
10
7
23
25
24
30
28
31
29
27
FIG.
PAGE
FIG.
PAGE
A
N
S
I
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 4
Description Ni-Alubronze gate valve, female threaded ends, Union Bonnet (UB), Inside Screwed Rising
Stem (ISRS), rising hand wheel, metal seated, back seat, pressure class 150#.
Fig. 1400-C958
A
N
S
I ISRS, Union Bonnet, 150#
Gate Valves
NAB (Ni-Alubronze)
Threaded
Materials
Parts Description Figure 1400-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Union Nut Cast Ni-Alubronze
ASTM B148-C95800
Wedge Cast Ni-Alubronze
ASTM B148-C95800
Stem Alu-Bronze
ASTM B150-C63200
Hand Wheel Cast Iron
ASTM A126
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN L H øW Weight [Kg]
1/2” 59 139 80 0.51
3/4” 64 160 80 0.77
1” 74 205 100 1.08
1 1/4” 83 230 100 1.69
1 1/2” 86 256 125 2.12
2” 87 311 140 3.53
2 1/2” 110 364 140 5.77
3” 135 442 160 8.51
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face Manufacturer’s standard, see below dimensions table
Thread Dimensions NPT female thread in accordance with ASME B1.20.1
Pressure Rating MSS SP-80-Class 150#*
Temperature Range -29°C to +232°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With BSP female threaded ends (Suffix BSP)
- With secured bonnet (Suffix SB)
Technical Features
Marking In accordance with MSS SP-25
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to MSS SP-80* [Barg / °C]
-29/+66 +93 +121 +149 +177 +208 +232 °C
½”-3” 150# 20.68 18.62 16.55 14.48 12.41 10.34 10.00 Barg
* Above P-T table is extracted from MSS SP-80 material B62. MSS SP-80 only lists P-T ratings for class 150# threaded valves in material B62 bronze
Please note that GVC uses Ni-Alubronze Grade C95800 which has better mechanical properties compared to B62 (Tin) bronze
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 5
Description Ni-Alubronze gate valve, female threaded ends, Union Bonnet (UB), Inside Screwed Rising
Stem (ISRS), rising hand wheel, metal seated, back seat, pressure class 300#.
Fig. 1401-C958
A
N
S
I ISRS, Union Bonnet, 300#
Gate Valves
NAB (Ni-Alubronze)
Threaded
Materials
Parts Description Figure 1401-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Union Nut Cast Ni-Alubronze
ASTM B148-C95800
Wedge Cast Ni-Alubronze
ASTM B148-C95800
Stem Alu-Bronze
ASTM B150-C63200
Hand Wheel Cast Iron
ASTM A126
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN L H øW Weight [Kg]
1/2” 59 139 80 0.55
3/4” 64 160 80 1.01
1” 74 205 100 1.53
1 1/4” 83 230 100 2.16
1 1/2” 86 256 125 2.87
2” 87 311 140 4.97
3” 135 442 160 9.01
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face In accordance with manufacturer’s standard, see below dimensions table
Thread Dimensions NPT female thread in accordance with ASME B1.20.1
Pressure Rating In accordance with MSS SP-80-Class 300#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With BSP female threaded ends (Suffix BSP)
- With secured bonnet (Suffix SB)
Technical Features
Marking In accordance with MSS SP-25
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to MSS SP-80* [Barg / °C]
-29/+66 +93 +121 +149 +177 +204 +232 +260 °C
½”-3” 300# 41.37 38.61 36.20 33.78 31.03 28.27 25.86 23.44 Barg
* Above P-T table is extracted from MSS SP-80 material B61. MSS SP-80 only lists P-T ratings for class 300# threaded valves in material B61 bronze
Please note that GVC uses Ni-Alubronze Grade C95800 which has better mechanical properties compared to B61 (Tin) bronze
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 6
Description Ni-Alubronze gate valve, flanged ends (Flat Faced), Union Bonnet (UB), Inside Screwed
Rising Stem (ISRS), rising hand wheel, back seat, pressure class 150#.
Fig. 1850 UB-C958
A
N
S
I ISRS, Union Bonnet, 150#
Gate Valves
NAB (Ni-Alubronze)
Flanged
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 7
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With secured bonnet (Suffix SB)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with MSS SP-25
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
½”-3” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
9.7
225
9.7
250
9.7
Materials
Parts Description Figure 1850 UB-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Union Nut Cast Ni-Alubronze
ASTM B148-C95800
Wedge Cast Ni-Alubronze
ASTM B148-C95800
Stem Alu-Bronze
ASTM B150-C63200
Hand Wheel Cast Iron
ASTM A126
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN L øW H Weight
[Kg]
1/2” DN15 108 90 170 3.2
3/4” DN20 117 100 190 4.3
1” DN25 127 100 230 6.4
1 1/4” DN32 140 125 270 9.1
1 1/2” DN40 165 125 290 11.5
2” DN50 178 160 305 18.0
3” DN80 203 160 440 28.0
ød
13
20
26
32
39
51
77
øD
90
100
110
115
125
150
190
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 7
Description Ni-Alubronze gate valve, flanged ends (Flat Faced), Union Bonnet (UB), Inside Screwed
Rising Stem (ISRS), rising hand wheel, back seat, pressure class 300#.
Fig. 1851 UB-C958
A
N
S
I ISRS, Union Bonnet, 300#
Gate Valves
NAB (Ni-Alubronze)
Flanged
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face In accordance with ASME B16.10:2000 Table 2 Column 10
Flange Dimensions In accordance with ASME B16.5-Class 300# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 300#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With secured bonnet (Suffix SB)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with MSS SP-25
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
½”-1½” 300# 35.6 33.0 27.4 26.3 25.5 25.2 24.9 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 300#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
25.2
225
24.9
250
24.9
Materials
Parts Description Figure 1851 UB-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Union Nut Cast Ni-Alubronze
ASTM B148-C95800
Wedge Cast Ni-Alubronze
ASTM B148-C95800
Stem Alu-Bronze
ASTM B150-C63200
Hand Wheel Cast Iron
ASTM A126
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN ød L øD øW H Weight
[Kg]
1/2” DN15 13 140 95 90 180 4.0
3/4” DN20 20 152 115 100 200 7.8
1” DN25 26 165 125 100 250 7.0
1 1/4” DN32 32 178 135 125 290 10.0
1 1/2” DN40 39 190 155 125 310 12.5
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 8
Description Ni-Alubronze gate valve, flanged ends (Flat Faced), Bolted Bonnet (BB), Inside Screwed
Non Rising Stem (ISNRS), non rising hand wheel, position indicator, pressure class 150#.
A
N
S
I ISNRS, Bolted Bonnet, 150#
Gate Valves
NAB (Ni-Alubronze)
Flanged
Design Generally in accordance with MSS SP-70 and ASME B16.34
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-70, API 598
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 7
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With drain plug (Suffix DP)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with MSS SP-25
Materials
Parts Description Figure 1840-C958
Body Cast Ni-Alubronze ASTM B148-C95800
Position Indicator Brass
Wedge Cast Ni-Alubronze ASTM B148-C95800
Stem Alu-Bronze ASTM B150-C63200
Hand Wheel Cast Iron ASTM A126
Bonnet Cast Ni-Alubronze ASTM B148-C95800
Dimensions [mm]
DN ød øC øD n-h L H øW Weight
[Kg]
2” DN50 50 120.5 152 4-19 178 286 127 15
2 1/2” DN65 65 139.5 178 4-19 190 330 140 20
3” DN80 80 152.5 191 4-19 203 330 160 24
4” DN100 100 190.5 229 8-19 229 432 181 38
5” DN125 125 216.0 254 8-22 254 495 200 52
6” DN150 150 241.5 279 8-22 267 559 225 70
8” DN200 200 298.5 343 8-22 292 679 279 122
10” DN250 250 362.0 406 12-25 330 800 356 191
12” DN300 300 432.0 483 12-25 356 845 381 289
Fig. 1840-C958
Position Indicator
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
2”-12” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
9.7
225
9.7
250
9.7
Position Indicator Detail
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 9
Fig. 1850-C958
A
N
S
I OS&Y, Bolted Bonnet, 150#
Gate Valves
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze gate valve, flanged ends (Flat Faced), Bolted Bonnet (BB), Outside Screwed
and Yoke (OS&Y), rising stem, non rising hand wheel, back seat, pressure class 150#.
Design Generally in accordance with API 600
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 600, API 598
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 7
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- in other bronze materials
- With Monel Trim (Suffix MON)
- With drain plug (Suffix DP)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 600, ISO 5209
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
2”-24” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
9.7
225
9.7
250
9.7
Materials
Parts Description Figure 1850-C958
Body, Bonnet, Wedge Cast Ni-Alubronze ASTM B148-C95800
Stem Alu-Bronze ASTM B150-C63200
Gaskets & Packing Graphite
Bolting, Fasteners Stainless Steel A194-8M & A193-B8M
Hand Wheel Ductile Iron ASTM A395
Body Seat Ring Cast Ni-Alubronze ASTM B148-C95800
Back Seat Ring Alu-Bronze ASTM B150-C63200
Dimensions [mm]
ød øC øD H L n-øh øW Weight
2” DN50 51 120.7 150 297 178 4-19.1 200 18 Kg
2½” DN65 64 139.7 180 310 190 4-19.1 200 21 Kg
3” DN80 76 152.4 190 364 203 4-19.1 224 24 Kg
4” DN100 102 190.5 230 435 229 8-19.1 250 37 Kg
6” DN150 152 241.3 280 552 267 8-22.2 315 69 Kg
8” DN200 203 298.5 345 702 292 8-22.2 355 109 Kg
10” DN250 254 362.0 405 849 330 12-25.4 400 164 Kg
12” DN300 305 431.8 485 1053 356 12-25.4 450 235 Kg
12” * DN300 * 305 431.8 485 1053 356 12-25.4 500 285 Kg
14” * DN350 * 337 476.3 535 1353 381 12-28.6 500 397 Kg
16” * DN400 * 387 539.8 595 1428 406 16-28.6 500 511 Kg
18” * DN450 * 438 577.9 635 1700 432 16-31.8 630 729 Kg
20” * DN500 * 489 635.0 700 1850 457 20-31.8 710 911 Kg
24” * DN600 * 591 749.3 815 2120 508 20-34.9 710 1464 Kg
* Executed with Gear Operator
DN
5” DN125 127 216.0 255 495 254 8-22.2 315 53 Kg
Bonnet Construction
2”~6” 8”~12” 12”~24”
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 10
Fig. 1851-C958
A
N
S
I OS&Y, Bolted Bonnet, 300#
Gate Valves
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze gate valve, flanged ends (Flat Faced), Bolted Bonnet (BB), Outside Screwed
and Yoke (OS&Y), rising stem, non rising hand wheel, back seat, pressure class 300#.
Design Generally in accordance with API 600
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 600, API 598
Face to Face In accordance with ASME B16.10:2000 Table 2 Column 10
Flange Dimensions In accordance with ASME B16.5-Class 300# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 300#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With drain plug (Suffix DP)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 600, ISO 5209
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
2”-24” 300# 35.6 33.0 27.4 26.3 25.5 25.2 24.9 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 300#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
25.2
225
24.9
250
24.9
Materials
Parts Description Figure 1851-C958
Body, Bonnet, Wedge Cast Ni-Alubronze ASTM B148-C95800
Stem Alu-Bronze ASTM B150-C63200
Gaskets & Packing Graphite
Bolting, Fasteners Stainless Steel A194-8M & A193-B8M
Hand Wheel Ductile Iron ASTM A395
Body Seat Ring Cast Ni-Alubronze ASTM B148-C95800
Back Seat Ring Alu-Bronze ASTM B150-C63200
Dimensions [mm]
ød øC øD H L n-øh øW Weight
2” DN50 51 127.0 165 361 216 8-19.1 200 26 Kg
2½” DN65 64 149.2 190 386 241 8-22.2 200 36 Kg
3” DN80 76 168.3 210 407 282 8-22.2 224 43 Kg
4” DN100 102 200.0 255 499 305 8-22.2 250 67 Kg
6” DN150 152 269.9 320 661 403 12-22.2 355 128 Kg
8” DN200 203 330.2 380 817 419 12-25.4 450 198 Kg
10” DN250 254 387.4 445 985 457 16-28.6 450 294 Kg
12” DN300 305 450.8 520 1138 502 16-31.8 500 446 Kg
12” * DN300 * 305 450.8 520 1220 502 16-31.8 630 566 Kg
14” * DN350 * 337 514.4 585 1300 762 20-31.8 710 693 Kg
16” * DN400 * 387 571.5 650 1745 838 20-34.9 800 950 Kg
18” * DN450 * 432 628.6 710 2010 914 24-34.9 900 1150 Kg
20” * DN500 * 483 685.8 775 2330 991 24-34.9 900 1500 Kg
24” * DN600 * 584 812.8 915 2784 1143 24-41.2 1000 2250 Kg
* Executed with Gear Operator
DN
5” DN125 127 234.9 280 615 381 8-22.2 315 88 Kg
Bonnet Construction
2”~4” 6”~12” 12”~24”
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 11
Description Ni-Alubronze globe valve, female threaded ends, Union Bonnet (UB), Inside Screwed
Rising Stem (ISRS), rising hand wheel, metal seated, plug type disc, back seat, pressure
class 150#.
Fig. 1410-C958
A
N
S
I ISRS, Union Bonnet, 150#
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face Manufacturer’s standard, see below dimensions table
Thread Dimensions NPT female thread in accordance with ASME B1.20.1
Pressure Rating MSS SP-80-Class 150#*
Temperature Range -29°C to +232°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With BSP female threaded (Suffix BSP)
- With secured bonnet (Suffix SB)
- With Screw Down Non Return Stop / Check Disc (Suffix SDNR)
Technical Features
Marking In accordance with MSS SP-25
Globe Valves
NAB (Ni-Alubronze)
Threaded
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to MSS SP-80* [Barg / °C]
-29/+66 +93 +121 +149 +177 +208 +232 °C
½”-3” 150# 20.68 18.62 16.55 14.48 12.41 10.34 10.00 Barg
* Above P-T table is extracted from MSS SP-80 material B62. MSS SP-80 only lists P-T ratings for class 150# threaded valves in material B62 bronze
Please note that GVC uses Ni-Alubronze Grade C95800 which has better mechanical properties compared to B62 (Tin) bronze
Materials
Parts Description Figure 1410-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Union Nut Cast Ni-Alubronze
ASTM B148-C95800
Wedge Cast Ni-Alubronze
ASTM B148-C95800
Stem Alu-Bronze
ASTM B150-C63200
Hand Wheel Cast Iron
ASTM A126
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN L H øW Weight [Kg]
1/2” 68 134 80 0.73
3/4” 81 134 80 1.06
1” 95 165 100 1.61
1 1/4” 108 175 100 2.61
1 1/2” 121 190 125 3.44
2” 146 254 140 5.70
2 1/2” 168 265 140 7.91
3” 197 302 160 10.83
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 12
Fig. 1411-C958
A
N
S
I ISRS, Union Bonnet, 300#
Globe Valves
NAB (Ni-Alubronze)
Threaded
Description Ni-Alubronze globe valve, female threaded ends, Union Bonnet (UB), Inside Screwed
Rising Stem (ISRS), rising hand wheel, metal seated, plug type disc, back seat, pressure
class 300#.
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face Manufacturer’s standard, see below dimensions table
Thread Dimensions NPT female thread in accordance with ASME B1.20.1
Pressure Rating MSS SP-80-Class 300#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With BSP female threaded (Suffix BSP)
- With secured bonnet (Suffix SB)
- With Screw Down Non Return Stop / Check Disc (Suffix SDNR)
Technical Features
Marking In accordance with MSS SP-25
Materials
Parts Description Figure 1411-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Union Nut Cast Ni-Alubronze
ASTM B148-C95800
Wedge Cast Ni-Alubronze
ASTM B148-C95800
Stem Alu-Bronze
ASTM B150-C63200
Hand Wheel Cast Iron
ASTM A126
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN L H øW Weight [Kg]
1/2” 68 134 80 0.77
3/4” 81 134 100 1.29
1” 95 165 100 2.18
1 1/4” 108 175 125 3.19
1 1/2” 121 190 140 3.78
2” 146 254 160 6.19
2 1/2” 168 265 160 8.21
3” 197 302 160 11.52
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to MSS SP-80* [Barg / °C]
-29/+66 +93 +121 +149 +177 +204 +232 +260 °C
½”-3” 300# 41.37 38.61 36.20 33.78 31.03 28.27 25.86 23.44 Barg
* Above P-T table is extracted from MSS SP-80 material B61. MSS SP-80 only lists P-T ratings for class 300# threaded valves in material B61 bronze
Please note that GVC uses Ni-Alubronze Grade C95800 which has better mechanical properties compared to B61 (Tin) bronze
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 13
Fig. 1820 UB-C958
A
N
S
I ISRS, Union Bonnet, 150#
Globe Valves
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze globe valve, flanged ends (Flat Faced), Union Bonnet (UB), Inside Screwed
Rising Stem (ISRS), rising hand wheel, metal seated, plug type disc, back seat, pressure
class 150#.
Design Generally in accordance with MSS SP-80 and BS 1873
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 15
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With secured bonnet (Suffix SB)
- With Screw Down Non Return Stop / Check Disc (Suffix SDNR)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with MSS SP-25
Materials
Parts Description Figure 1820 UB-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Union Nut Cast Ni-Alubronze
ASTM B148-C95800
Wedge Cast Ni-Alubronze
ASTM B148-C95800
Stem Alu-Bronze ASTM
B150-C63200
Hand Wheel Cast Iron ASTM
A126
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
ød øD L H øW Weight
[Kg]
1/2” DN15 13 90 108 205 80 3
3/4” DN20 20 100 117 215 100 4
1” DN25 26 110 127 235 125 6
1 1/4” DN32 32 115 140 240 125 9
1 1/2” DN40 39 125 165 255 140 9
DN
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
½”-1½” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
9.7
225
9.7
250
9.7
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 14
Fig. 1821 UB-C958
A
N
S
I ISRS, Union Bonnet, 300#
Globe Valves
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze globe valve, flanged ends (Flat Faced), Union Bonnet (UB), Inside Screwed
Rising Stem (ISRS), rising hand wheel, metal seated, plug type disc, back seat, pressure
class 300#.
Design Generally in accordance with MSS SP-80 and BS 1873
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face In accordance with ASME B16.10:2000 Table 2 Column 15
Flange Dimensions In accordance with ASME B16.5-Class 300# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 300#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With secured bonnet (Suffix SB)
- With Screw Down Non Return Stop / Check Disc (Suffix SDNR)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with MSS SP-25
Materials
Parts Description Figure 1821 UB-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Union Nut Cast Ni-Alubronze
ASTM B148-C95800
Wedge Cast Ni-Alubronze
ASTM B148-C95800
Stem Alu-Bronze ASTM
B150-C63200
Hand Wheel Cast Iron ASTM
A126
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
ød øD L H øW Weight
[Kg]
1/2” DN15 13 95 152 215 80 4
3/4” DN20 20 115 178 225 100 5
1” DN25 26 125 203 250 125 8
1 1/4” DN32 32 135 216 260 125 11
1 1/2” DN40 39 155 229 275 140 12
DN
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
½”-1½” 300# 35.6 33.0 27.4 26.3 25.5 25.2 24.9 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 300#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
25.2
225
24.9
250
24.9
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 15
Fig. 1820-C958
A
N
S
I OS&Y, Bolted Bonnet, 150#
Globe Valves
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze globe valve, flanged ends (Flat Faced), Bolted Bonnet (BB), Outside Screwed
and Yoke (OS&Y), rising stem, rising hand wheel, back seat, pressure class 150#.
Design Generally in accordance with BS 1873
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with BS 1873, API 598
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 15
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With drain plug (Suffix DP)
- With Screw Down Non Return Stop / Check Disc (Suffix SDNR)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with BS 1873
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
2”-16” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
9.7
225
9.7
250
9.7
Materials
Parts Description Figure 1820-C958
Body, Bonnet, Disc Cast Ni-Alubronze
ASTM B148-C95800
Stem, Back Seat Ring Alu-Bronze
ASTM B150-C63200
Gaskets & Packing Graphite
Bolting, Fasteners Stainless Steel A194-8M & A193-B8M
Hand Wheel Cast Iron ASTM A126
Body Seat Ring Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN ød øC øD H L n-øh øW Weight
2” DN50 51 120.7 150 366 203 4-19.1 180 18 Kg
2½” DN65 64 139.7 180 394 216 4-19.1 180 29 Kg
3” DN80 76 152.4 190 415 241 4-19.1 200 32 Kg
4” DN100 102 190.5 230 504 292 8-19.1 224 45 Kg
5” DN125 127 216.0 255 555 356 8-22.2 250 69 Kg
6” DN150 152 241.3 280 580 406 8-22.2 280 85 Kg
8” DN200 203 298.5 345 715 495 8-22.2 355 148 Kg
10” DN250 254 362.0 405 792 622 12-25.4 450 239 Kg
12” DN300 305 431.8 485 865 698 12-25.4 500 332 Kg
8” * DN200 203 298.5 345 620 495 8-22.2 400 198 Kg
10” * DN250 254 362.0 405 710 622 12-25.4 500 289 Kg
12” * DN300 * 305 431.8 485 850 698 12-25.4 630 365 Kg
14” * DN350 * 337 476.3 535 950 787 12-28.6 710 630 Kg
16” * DN400 * 387 539.8 595 1070 914 16-28.6 800 850 Kg
* Executed with Gear Operator
With Gear Operator
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 16
Fig. 1821-C958
A
N
S
I OS&Y, Bolted Bonnet, 300#
Globe Valves
NAB (Ni-Alubronze)
Flanged
With Gear Operator
Description Ni-Alubronze globe valve, flanged ends (Flat Faced), Bolted Bonnet (BB), Outside Screwed
and Yoke (OS&Y), rising stem, rising hand wheel, back seat, pressure class 300#.
Design Generally in accordance with BS 1873
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with BS 1873, API 598
Face to Face In accord. with ASME B16.10:2000 Table 2 Column 15
Flange Dimensions In accordance with ASME B16.5-Class 300# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 300#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With drain plug (Suffix DP)
- With Screw Down Non Return Stop / Check Disc (Suffix SDNR)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with BS 1873
Materials
Parts Description Figure 1821-C958
Body, Bonnet, Disc Cast Ni-Alubronze
ASTM B148-C95800
Stem, Back Seat Ring Alu-Bronze
ASTM B150-C63200
Gaskets & Packing Graphite
Bolting, Fasteners Stainless Steel
A194-8M & A193-B8M
Hand Wheel Cast Iron
ASTM A126
Body Seat Ring Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN ød øC øD H L n-øh øW Weight
2” DN50 51 127.0 165 378 267 8-19.1 180 29 Kg
2½” DN65 64 149.0 190 425 292 8-22.2 200 38 Kg
3” DN80 76 168.3 210 464 318 8-22.2 224 58 Kg
4” DN100 102 200.0 255 565 356 8-22.2 280 90 Kg
5” DN125 127 234.9 280 620 400 8-22.2 355 154 Kg
6” DN150 152 269.9 320 741 444 12-22.2 400 171 Kg
8” DN200 203 330.2 380 805 559 12-25.4 500 243 Kg
10” DN250 254 387.4 445 883 622 16-28.6 560 367 Kg
12” DN300 305 450.8 520 926 711 16-31.8 500 474 Kg
8” * DN200 203 330.2 380 899 533 12-25.4 710 293 Kg
10” * DN250 254 387.4 445 1107 622 16-28.6 800 477 Kg
12” * DN300 * 305 450.8 520 1202 711 16-31.8 900 700 Kg
14” * DN350 * 337 514.4 585 1390 838 20-31.8 1000 880 Kg
* Executed with Gear Operator
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
2”-14” 300# 35.6 33.0 27.4 26.3 25.5 25.2 24.9 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 300#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
25.2
225
24.9
250
24.9
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 17
Fig. 1430-C958
A
N
S
I Y-Type, Screwed Bonnet, 150#
Check Valves, Swing
NAB (Ni-Alubronze)
Threaded
Description Ni-Alubronze swing check, y-type, female threaded ends, Screwed Bonnet (SB),
metal seated, pressure class 150#.
Materials
Parts Description Figure 1430-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Disc Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN L H Weight
[Kg]
1/2” 62 43 0.27 Kg
3/4” 75 48 0.44 Kg
1” 90 62 0.72 Kg
1 1/4” 106 68 1.08 Kg
1 1/2” 114 75 1.43 Kg
2” 133 100 2.45 Kg
2 1/2” 203 129 5.21 Kg
3” 235 159 7.95 Kg
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face Manufacturer’s standard, see below dimensions table
Thread Dimensions NPT female thread in accordance with ASME B1.20.1
Pressure Rating MSS SP-80-Class 150#*
Temperature Range -29°C to +232°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- BSP female threaded (Suffix BSP)
Technical Features
Marking In accordance with MSS SP-25
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to MSS SP-80* [Barg / °C]
-29/+66 +93 +121 +149 +177 +208 +232 °C
½”-3” 150# 20.68 18.62 16.55 14.48 12.41 10.34 10.00 Barg
* Above P-T table is extracted from MSS SP-80 material B62. MSS SP-80 only lists P-T ratings for class 150# threaded valves in material B62 bronz
Please note that GVC uses Ni-Alubronze Grade C95800 which has better mechanical properties compared to B62 (Tin) bronze
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 18
Fig. 1431-C958
A
N
S
I Y-Type, Screwed Bonnet, 300#
Check Valves, Swing
NAB (Ni-Alubronze)
Threaded
Description Ni-Alubronze swing check, y-type, female threaded ends, Screwed Bonnet (SB),
metal seated, pressure class 300#.
Materials
Parts Description Figure 1431-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Disc Cast Ni-Alubronze
ASTM B148-C95800
Dimensions [mm]
DN L H Weight
[Kg]
1/2” 67 44 0.31 Kg
3/4” 79 52 0.46 Kg
1” 95 62 0.75 Kg
1 1/4” 111 79 1.35 Kg
1 1/2” 125 95 2.18 Kg
2” 148 114 3.69 Kg
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face Manufacturer’s standard, see below dimensions table
Thread Dimensions NPT female thread in accordance with ASME B1.20.1
Pressure Rating MSS SP-80-Class 300#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- BSP female threaded (Suffix BSP)
Technical Features
Marking In accordance with MSS SP-25
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to MSS SP-80* [Barg / °C]
-29/+66 +93 +121 +149 +177 +204 +232 +260 °C
½”-2” 300# 41.37 38.61 36.20 33.78 31.03 28.27 25.86 23.44 Barg
* Above P-T table is extracted from MSS SP-80 material B61. MSS SP-80 only lists P-T ratings for class 300# threaded valves in material B61 bronze
Please note that GVC uses Ni-Alubronze Grade C95800 which has better mechanical properties compared to B61 (Tin) bronze
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 19
Fig. 1810 SB-C958
A
N
S
I Screwed Bonnet, 150#
Check Valves, Swing
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze swing check valve, flanged ends (Flat Faced), Screwed Bonnet (SB),
metal seated, pressure class 150#.
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 15
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- BSP female threaded (Suffix BSP)
Technical Features
Marking In accordance with MSS SP-25
Dimensions [mm]
DN ød øD L H Weight
[Kg]
1/2” DN15 13 90 108 69 2.1 Kg
3/4” DN20 20 100 117 69 2.2 Kg
1” DN25 26 110 127 69 2.3 Kg
1 1/4” DN32 32 116 140 79 3.1 Kg
1 1/2” DN40 39 125 165 93 4.3 Kg
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
½”-1½” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
9.7
225
9.7
250
9.7
Materials
Parts Description Figure 1810 SB-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Bonnet Cast Ni-Alubronze
ASTM B148-C95800
Disc Cast Ni-Alubronze
ASTM B148-C95800
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 20
Fig. 1810-C958
A
N
S
I Bolted Cover, 150#
Check Valves, Swing
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze swing check, flanged ends (Flat Faced), Bolted Cover (BC), metal seated,
pressure class 150#.
Design Generally in accordance with API 6D, ISO 14313
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 6D, API 598
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 15
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...) and in other bronze materials
- With Monel Trim (Suffix MON)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 6D, ISO 14313
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
2”-24” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
9.7
225
9.7
250
9.7
Materials
Parts Description Figure 1810-C958
Body Cast Ni-Alubronze ASTM B148-C95800
Disc Nut, Split Pin SS316
Disc Arm Cast Ni-Alubronze ASTM B148-C95800
Body Seat Ring Cast Ni-Alubronze ASTM B148-C95800
Hinge Pin Alu-Bronze ASTM B150-C63200
Hinge Pin Plug Alu-Bronze ASTM B150-C63200
Cover Gasket Graphite
Bolting, Fasteners Stainless Steel A194-8M & A193-B8M
Eye Bolt SS316 (For sizes ≥ 6” [DN150])
Cover Cast Ni-Alubronze ASTM B148-C95800
Disc Cast Ni-Alubronze ASTM B148-C95800
Dimensions [mm]
DN ød øC øD H L n-øh Weight
2” DN50 51 120.7 150 126 203 4-19.1 21 Kg
2½” DN65 64 139.7 180 148 216 4-19.1 28 Kg
3” DN80 77 152.4 190 160 241 4-19.1 32 Kg
4” DN100 102 190.5 230 187 292 8-19.1 51 Kg
6” DN150 153 241.3 280 280 356 8-22.2 96 Kg
8” DN200 204 298.5 345 327 495 8-22.2 119 Kg
10” DN250 254 362.0 405 407 622 12-25.4 211 Kg
12” DN300 305 431.8 485 430 698 12-25.4 297 Kg
14” DN350 337 476.3 535 460 787 12-28.6 370 Kg
16” DN400 388 539.8 595 545 864 16-28.6 461 Kg
18” DN450 439 577.9 635 650 978 16-31.8 640 Kg
20” DN500 489 635.0 700 670 978 20-31.8 780 Kg
24” DN600 591 749.3 815 900 1295 20-34.9 1490 Kg
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 21
Fig. 1811-C958
A
N
S
I Bolted Cover, 300#
Check Valves, Swing
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze swing check, flanged ends (Flat Faced), Bolted Cover (BC), metal seated,
pressure class 300#.
Design Generally in accordance with API 6D, ISO 14313
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 6D, API 598
Face to Face In accord. with ASME B16.10:2000 Table 2 Column 17
Flange Dimensions In accordance with ASME B16.5-Class 300# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 300#*
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...) and in other bronze materials
- With Monel Trim (Suffix MON)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 6D, ISO 14313
Materials
Parts Description Figure 1811-C958
Body Cast Ni-Alubronze ASTM B148-C95800
Hinge Pin Alu-Bronze ASTM B150-C63200
Cover Gasket Graphite
Bolting, Fasteners Stainless Steel A194-8M & A193-B8M
Eye Bolt SS316 (For sizes ≥ 4” [DN100])
Body Seat Ring Cast Ni-Alubronze ASTM B148-C95800
Disc Arm Cast Ni-Alubronze ASTM B148-C95800
Cover Cast Ni-Alubronze ASTM B148-C95800
Disc Cast Ni-Alubronze ASTM B148-C95800
Hinge Pin Plug Alu-Bronze ASTM B150-C63200
Disc Nut, Split Pin SS316
Dimensions [mm]
DN ød øC øD H L n-øh Weight
2” DN50 51 127.0 165 163 267 8-19.1 24 Kg
2½” DN65 64 149.2 190 180 292 8-22.2 33 Kg
3” DN80 77 168.3 210 197 318 8-22.2 41 Kg
4” DN100 102 200.0 255 220 356 8-22.2 61 Kg
6” DN150 153 269.9 320 288 444 12-22.2 123 Kg
8” DN200 204 330.2 380 332 533 12-25.4 198 Kg
10” DN250 254 387.4 445 426 622 16-28.6 243 Kg
12” DN300 305 450.8 520 468 711 16-31.8 446 Kg
14” DN350 337 514.4 585 580 838 20-31.8 682 Kg
16” DN400 388 571.5 650 695 864 20-34.9 747 Kg
18” DN450 432 628.6 710 776 978 24-34.9 1250 Kg
20” DN500 483 685.8 775 797 1016 24-34.9 1500 Kg
24” DN600 585 812.8 915 1007 1346 24-41.2 2230 Kg
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
2”-24” 300# 35.6 33.0 27.4 26.3 25.5 25.2 24.9 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 300#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
25.2
225
24.9
250
24.9
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 22
Fig. 1450 UB-C958
A
N
S
I Union Bonnet, 150#
Check Valves, Lift
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze lift check valve, flanged ends (Flat Faced), Union Bonnet (UB),
metal seated, pressure class 150#.
Design Generally in accordance with MSS SP-80
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with MSS SP-80, API 598
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 15
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150# *
Temperature Range -29°C to +260°C
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- With secured bonnet (Suffix SB)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with MSS SP-25
Dimensions [mm]
DN ød øD L H Weight
[Kg]
1/2” DN15 13 90 108 66 1.6 Kg
3/4” DN20 20 100 117 71 2.2 Kg
1” DN25 26 110 127 81 2.8 Kg
1 1/4” DN32 32 115 140 83 3.9 Kg
1 1/2” DN40 39 125 165 91 5.5 Kg
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 260 °C
½”-1½” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
200
9.7
225
9.7
250
9.7
Materials
Parts Description Figure 1450 UB-C958
Body Cast Ni-Alubronze
ASTM B148-C95800
Cover Cast Ni-Alubronze
ASTM B148-C95800
Disc Cast Ni-Alubronze
ASTM B148-C95800
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 23
Description Ni-Alubronze duo-check valve, wafer type, soft NBR seated, spring loaded discs,
pressure class 150#.
Fig. 2238-C958
A
N
S
I 150#
Check Valves, Duo
NAB (Ni-Alubronze)
Wafer
Design Generally in accordance with API 594
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 594, API 598
Face to Face In accordance with API 594
Flange Dimensions Mounting between flanges in accord. with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150# *
Temperature Range -29°C to +260°C (NBR seated valves are limited to max. 80°C**)
Options - In other ASTM B148 material grades (Suffix C...) and in other bronze materials
- With Monel Trim (Suffix MON)
- Retainerless design (Suffix R)
- Metal Seated (Suffix MS)
- Other spring/seal/bearing materials
- In pressure class 300# (Suffix 300#)
- Suitable for mounting between other flanged connections DIN, JIS etc.
Technical Features
Marking In accordance with API 594, MSS SP-25
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 200 225 250 260 °C
2”-24” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
** NBR seated valves are limited to maximum +80°C
80**
10.5
Materials
Parts Description Figure 2238-C958
Body, Discs Cast Ni-Alubronze
ASTM B148-C95800
Cover Cast Ni-Alubronze
ASTM B148-C95800
Seal NBR Rubber
Hinge Pin, Stop Pin, Spring Stainless Steel
ASTM A276-316
Bearings Brass
ASTM B124-C37700
Eye Bolt SS316 (For sizes ≥ 10” [DN250])
Dimensions [mm]
DN ød øD L
2” DN50 60 105 60
2½” DN65 73 124 67
3” DN80 89 137 73
4” DN100 114 175 73
5” DN125 141 197 86
6” DN150 168 222 98
8” DN200 219 279 127
10” DN250 273 340 146
12” DN300 324 410 181
14” DN350 356 451 184
16” DN400 406 514 191
18” DN450 457 549 203
20” DN500 508 606 219
24” DN600 610 718 222
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 24
Fig. 2238 LUG-C958
A
N
S
I 150#
Check Valves, Duo
NAB (Ni-Alubronze)
Lug
Description Ni-Alubronze duo-check valve, Lug type, soft NBR seated, spring loaded discs, tapped bolt
holes, pressure class 150#.
Design Generally in accordance with API 594
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 594, API 598
Face to Face In accordance with API 594
Flange Dimensions Mounting between flanges in accord. with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150# *
Temperature Range -29°C to +260°C (NBR seated valves are limited to max. 80°C**)
Options - In other ASTM B148 material grades (Suffix C...) and in other bronze materials
- With Monel Trim (Suffix MON)
- Metal Seated (Suffix MS)
- Retainerless design (Suffix R)
- Non threaded bolt holes (Suffix NTH)
- Other spring/seal/bearing materials
- In pressure class 300# (Suffix 300#)
- Suitable for mounting between other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 594, MSS SP-25
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 200 225 250 260 °C
2”-24” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
** NBR seated valves are limited to maximum +80°C
80**
10.5
Materials
Parts Description Figure 2238 LUG-C958
Body, Discs Cast Ni-Alubronze ASTM B148-C95800
Cover Cast Ni-Alubronze ASTM B148-C95800
Seal NBR Rubber
Hinge Pin, Stop Pin, Spring Stainless Steel ASTM A276-316
Bearings Brass ASTM B124-C37700
Eye Bolt SS316 (For sizes ≥ 10” [DN250])
Dimensions [mm]
DN ød øD L
2” DN50 60 150 60
2½” DN65 73 180 67
3” DN80 89 190 73
4” DN100 114 230 73
5” DN125 141 255 86
6” DN150 168 280 98
8” DN200 219 345 127
10” DN250 273 405 146
12” DN300 324 485 181
14” DN350 356 535 184
16” DN400 406 595 191
18” DN450 457 635 203
20” DN500 508 700 219
24” DN600 610 815 222
øC
120.7
139.7
152.4
190.5
215.9
241.3
298.5
362.0
431.8
476.3
539.8
577.9
635.0
749.3
n x øh
4 x 5/8”
4 x 5/8”
4 x 5/8”
8 x 5/8”
8 x 3/4”
8 x 3/4”
8 x 3/4”
12 x 7/8”
12 x 7/8”
12 x 1”
16 x 1”
16 x 1 1/8”
20 x 1 1/8”
16 x 1 1/4”
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 25
Fig. 2238 FL-C958
A
N
S
I 150#
Check Valves, Duo
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze duo-check valve, flanged ends (Flat Faced), soft NBR seated, spring loaded
discs, tapped bolt holes, pressure class 150# and 300#.
Design Generally in accordance with API 594
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 594, API 598
Face to Face In accordance with API 594
Flange Dimensions Mounting between flanges in accord. with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150#*
Temperature Range -29°C to +260°C (NBR seated valves are limited to max. 80°C**)
Options - In other ASTM B148 material grades (Suffix C...) and other bronze materials
- With Monel Trim (Suffix MON)
- Metal Seated (Suffix MS)
- Retainerless design (Suffix R)
- Other spring/seal/bearing materials
- In pressure class 300# (Suffix 300#)
- With other flanged connections DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 594, MSS SP-25
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175 200 225 250 260 °C
2”-24” 150# 13.4 12.5 10.5 9.9 9.7 9.7 9.7 9.7 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
** NBR seated valves are limited to maximum +80°C
80**
10.5
Materials
Parts Description Figure 2238 FL-C958
Body, Discs Cast Ni-Alubronze ASTM B148-C95800
Cover Cast Ni-Alubronze ASTM B148-C95800
Seal NBR Rubber
Hinge Pin, Stop Pin, Spring Stainless Steel ASTM A276-316
Bearings Brass ASTM B124-C37700
Eye Bolt SS316 (For sizes ≥ 10” [DN250])
Dimensions [mm]
DN ød øD L
2” DN50 57 150 60
2½” DN65 73 180 67
3” DN80 87 190 73
4” DN100 113 230 73
5” DN125 141 255 86
6” DN150 166 280 98
8” DN200 219 345 127
10” DN250 273 405 146
12” DN300 324 485 181
14” DN350 356 535 184
16” DN400 406 595 191
18” DN450 457 635 203
20” DN500 508 700 219
24” DN600 610 815 222
øC
120.7
139.7
152.4
190.5
215.9
241.3
298.5
362.0
431.8
476.3
539.8
577.9
635.0
749.3
n x øh
4 x 19.1
4 x 19.1
4 x 19.1
8 x 19.1
8 x 22.2
8 x 22.2
8 x 3/4”
12 x 25.4
12 x 25.4
12 x 28.6
16 x 28.6
16 x 31.8
20 x 31.8
20 x 34.9
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 26
A
N
S
I FB & RB, Split Body, 300#
Ball Valves
NAB (Ni-Alubronze)
Threaded
Fig. 1608-C958
Fig. 1608 RB-C958
Reduced Bore &
Full Bore
Description Ni-Alubronze ball valve, female threaded ends, 2 piece (split) body, floating ball, full and
reduced bore (RB), Screwed Cap, blow-out proof stem, PTFE seated, pressure class 300#
(Class 150# included).
Full Bore : GVC 1608-C958
Reduced Bore : GVC 1608 RB-C958
Materials
Parts Description Figure 1608-C958, 1608 RB-C9588
Body Cast Ni-Alubronze
ASTM B148-C95800
Cap Cast Ni-Alubronze
ASTM B148-C95800
Ball Cast Ni-Alubronze
ASTM B148-C95800
Stem Alu-Bronze
ASTM B150-C63200
Seat Rings PTFE
Hand Lever Stainless Steel
ASTM A240-304
Dimensions [mm]
Figure 1608-C958 Figure 1608 RB-C9588
DN L H W Weight
[Kg]
L H W Weight
[Kg]
1/2” 60 45 90.0 0.4 Kg 60 45 90 0.3 Kg
3/4” 75 55 105.0 0.7 Kg 70 45 90 0.6 Kg
1” 85 60 121.5 1.2 Kg 85 51 105 1.0 Kg
1 1/2” 102 60 105.0 2.6 Kg 102 60 105 2.3 Kg
2” -- -- -- -- 118 105 290 3.8 Kg
3” -- -- -- -- 180 112 290 11.6 Kg
Design Generally in accordance with ISO 17292
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with ISO 17292, ISO 5208, API 598
Face to Face Manufacturer’s standard, see below dimensions table
Thread Dimensions NPT female thread in accordance with ASME B1.20.1
Pressure Rating MSS SP-80-Class 300#*
Temperature Range -29°C to +175°C (PTFE seated valves are limited to max. +175°C**)
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- BSP female threaded (Suffix BSP)
- Other seat materials
Technical Features
Marking In accordance with ISO 17292, ISO 5209
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to MSS SP-80* [Barg / °C]
-29/+66 +93 +121 +149 +175** +177 +204 +232 +260 °C
½”-3” 300# 41.37 38.61 36.20 33.78 31.03 Barg
* Above P-T table is extracted from MSS SP-80 material B61. MSS SP-80 only lists P-T ratings for class 300# threaded valves in material B61 bronze
Please note that GVC uses Ni-Alubronze Grade C95800 which has better mechanical properties compared to B61 (Tin) bronze
** PTFE seated valves are limited to maximum +175°C
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 27
A
N
S
I FB, 3-Piece Body, 150#
Ball Valves
NAB (Ni-Alubronze)
Threaded
Fig. 7480-C958
Description Ni-Alubronze ball valve, female threaded ends, 3 piece body with full lug type center piece,
floating ball, full bore (FB), blow-out proof stem, anti-static device, Fire Safe design, PTFE
seated, pressure class 150#.
Materials
Parts Description Figure 7480-C958
Body Cast Ni-Alubronze ASTM B148-C95800
Caps Cast Ni-Alubronze ASTM B148-C95800
Ball Cast Ni-Alubronze ASTM B148-C95800
Stem Alu-Bronze ASTM B150-C63200
Seat Rings, Thrust Washer PTFE
Hand Lever Steel + Vinyl
Gaskets, Packing Graphite
Cap bolting Stainless Steel A193-B8M
External nuts Stainless Steel A194-8
Stopper Pin Brass ASTM B124-C37700
Stopper Plate, Locking Device, Belleville Washers Steel Galvanized
Dimensions [mm]
DN ød L L1 H
(Appr.)
W
3/8” 10 64 12.0 64 160
1/2” 15 70 13.5 72 160
3/4” 20 85 14.0 84 180
1” 25 100 17.5 94 180
1 1/4” 32 110 17.5 94 180
1 1/2” 38 120 18.5 100 230
2” 50 155 19.0 115 250
Design Generally in accordance with BS 5351
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In acc. with BS 5146 Part 1, API 598, Fire Safe tested and certified to API 6FA
Face to Face Manufacturer’s standard, see below dimensions table
Thread Dimensions NPT female thread in accordance with ASME B1.20.1
Pressure Rating MSS SP-80-Class 150#*
Temperature Range -29°C to +175°C (PTFE seated valves are limited to max. +175°C**)
Options - In other ASTM B148 material grades (Suffix C...)
- In other bronze materials
- With Monel Trim (Suffix MON)
- BSP female threaded (Suffix BSP)
- Other seat materials
- In pressure class 300#
Technical Features
Marking In accordance with BS 5418
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to MSS SP-80* [Barg / °C]
-29/+66 +93 +121 +149 +175** +177 +204 +232 +260 +288 °C
⅜”-2” 150# 20.68 18.62 16.55 14.48 12.41 Barg
* Above P-T table is extracted from MSS SP-80 material B62. MSS SP-80 only lists P-T ratings for class 150# threaded valves in material B62 bronze
Please note that GVC uses Ni-Alubronze Grade C95800 which has better mechanical properties compared to B62 (Tin) bronze
** PTFE seated valves are limited to maximum +175°C
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 28
Fig. 7235 RB-C958
A
N
S
I Red. Bore, Split Body, 150#
Ball Valves
NAB (Ni-Alubronze)
Flanged
Reduced Bore
≤ DN200 (Floating Ball)
> DN200 (Trunion mounted Ball)
Description Ni-Alubronze ball valve, flanged ends (Flat Faced), 2 piece body, (<DN250) floating ball,
(≥DN250) trunion mounted ball, reduced bore (RB), PTFE seated, anti-static device, blow-
out proof stem, gland packing, ISO 5211 mounting table, Fire Safe, pressure class 150#.
Design Generally in accordance with API 6D, ISO 14313, ASME B16.24
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 6D, API 598, Fire Safe tested and certified to API 607
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 18
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150# *
Temperature Range -29°C to +175°C (PTFE seated valves are limited to max. +175°C**)
Options - In other ASTM B148 material grades (Suffix C...) and in other bronze materials
- With Monel Trim (Suffix MON)
- With other flanged connections DIN, JIS etc.
- With other seat materials
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 6D, ISO 14313
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175** 200 225 250 260 °C
1/2”-24” 150# 13.4 12.5 10.5 9.9 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
** PTFE seated valves are limited to maximum +175°C
Materials
Parts Description Figure 7235 RB-C958
Body and Cap Cast Ni-Alubronze ASTM B148-C95800
Ball ≤ DN100 : Alu Bronze ASTM B150-C63200
> DN100 : Cast Ni-Alubronze ASTM B148-C95800
Stem Alu Bronze ASTM B150-C63200
Seat PTFE
Seat Retainer (> DN200) Alu Bronze ASTM B150-C63200
Dimensions [mm]
DN ød øD øC n x øh L H W
1/2” DN15 13 90 60.3 4-15.9 108 99 125
3/4” DN20 13 100 69.8 4-15.9 117 103 125
1” DN25 19 110 79.4 4-15.9 127 114 155
1 1/2” DN40 25 125 98.4 4-15.9 165 139 230
2” DN50 38 150 120.7 4-19.1 178 149 230
2 1/2” DN65 51 180 139.7 4-19.1 190 155 350
3” DN80 51 190 152.4 4-19.1 203 170 350
4” DN100 76 190 190.5 8-19.1 229 190 450
5” * DN125 102 255 215.9 8-22.2 356 300 ø 400
6” * DN150 102 280 241.3 8-22.2 394 316 ø 400
8” * DN200 152 345 298.5 8-22.2 457 336 ø 400
10” * DN250 203 405 362.0 12-25.4 533 396 ø 500
12” * DN300 254 485 431.8 12-25.4 610 396 ø 500
14” * DN350 305 535 476.3 12-28.6 686 417 ø 500
16” * DN400 337 595 539.8 16-28.6 762 417 ø 500
18” * DN450 387 635 577.9 16-31.8 864 458 ø 500
20” * DN500 438 700 635.0 20-31.8 914 526 ø 710
24” * DN600 489 815 749.3 20-34.9 1067 565 ø 710
* = With Gear Operator
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 29
Fig. 7236 RB-C958
A
N
S
I Red. Bore, Split Body, 300#
Ball Valves
NAB (Ni-Alubronze)
Flanged
Reduced Bore
≤ DN200 (Floating Ball)
> DN200 (Trunion mounted Ball)
Description Ni-Alubronze ball valve, flanged ends (Flat Faced), 2 piece body, (<DN250) floating ball,
(≥DN250) trunion mounted ball, reduced bore (RB), PTFE seated, anti-static device, blow-
out proof stem, gland packing, ISO 5211 mounting table, Fire Safe, pressure class 300#.
Design Generally in accordance with API 6D, ISO 14313, ASME B16.24
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 6D, API 598, Fire Safe tested and certified to API 607
Face to Face In accordance with ASME B16.10:2000 Table 2 Column 7
Flange Dimensions In accordance with ASME B16.5-Class 300# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 300# *
Temperature Range -29°C to +175°C (PTFE seated valves are limited to max. +175°C**)
Options - In other ASTM B148 material grades (Suffix C...) and in other bronze materials
- With Monel Trim (Suffix MON)
- With other flanged connections DIN, JIS etc.
- With other seat materials
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 6D, ISO 14313
Materials
Parts Description Figure 7236 RB-C958
Body and Cap Cast Ni-Alubronze ASTM B148-C95800
Ball ≤ DN100 : Alu Bronze ASTM B150-C63200
> DN100 : Cast Ni-Alubronze ASTM B148-C95800
Stem Alu Bronze ASTM B150-C63200
Seat PTFE
Seat Retainer (> DN200) Alu Bronze ASTM B150-C63200
Dimensions [mm]
DN ød øD øC n x øh L H W
1/2” DN15 13 95 66.7 4-15.9 140 99 125
3/4” DN20 13 117 82.5 4-19.1 152 103 125
1” DN25 19 123 88.9 4-19.1 165 114 155
1 1/2” DN40 25 155 114.0 4-22.2 190 139 230
2” DN50 38 165 127.0 8-19.1 216 149 230
2 1/2” DN65 51 190 149.2 8-22.2 241 155 350
3” DN80 51 210 168.3 8-22.2 282 170 350
4” DN100 76 255 200.0 8-22.2 305 190 450
5” * DN125 102 280 234.9 8-22.2 381 300 ø 400
6” * DN150 102 320 269.9 12-22.2 403 316 ø 400
8” * DN200 152 380 330.2 12-25.4 502 336 ø 400
10” * DN250 203 445 387.4 16-28.6 568 396 ø 500
12” * DN300 254 520 450.8 16-31.8 648 396 ø 500
14” * DN350 305 585 514.4 20-31.8 762 417 ø 500
16” * DN400 337 650 571.5 20-34.9 838 417 ø 500
18” * DN450 387 710 628.6 24-34.9 914 492 ø 710
20” * DN500 438 775 685.8 24-34.9 991 530 ø 710
24” * DN600 489 915 812.8 24-41.2 1143 582 ø 800
* = With Gear Operator
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175** 200 225 250 260 °C
1/2”-24” 300# 35.6 33.0 27.4 26.3 25.5 25.2 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 300#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
** PTFE seated valves are limited to maximum +175°C
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 30
Fig. 7235-C958
A
N
S
I Full Bore, Split Body, 150#
Ball Valves
NAB (Ni-Alubronze)
Flanged
Full Bore
≤ DN200 (Floating Ball)
> DN200 (Trunion mounted Ball)
Description Ni-Alubronze ball valve, flanged ends (Flat Faced), 2 piece body, (<DN250) floating ball,
(≥DN250) trunion mounted ball, Full Bore (FB), PTFE seated, anti-static device, blow-out
proof stem, gland packing, ISO 5211 mounting table, Fire Safe, pressure class 150#.
Design Generally in accordance with API 6D, ISO 14313, ASME B16.24
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 6D, API 598, Fire Safe tested and certified to API 607
Face to Face In accordance with ASME B16.10:2000 Table 1 Column 18
Flange Dimensions In accordance with ASME B16.5-Class 150# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 150#*
Temperature Range -29°C to +175°C (PTFE seated valves are limited to max. +175°C**)
Options - In other ASTM B148 material grades (Suffix C...) and in other bronze materials
- With Monel Trim (Suffix MON)
- With other flanged connections DIN, JIS etc.
- With other seat materials
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 6D, ISO 14313
Materials
Parts Description Figure 7235-C958
Body and Cap Cast Ni-Alubronze ASTM B148-C95800
Ball ≤ DN100 : Alu Bronze ASTM B150-C63200
> DN100 : Cast Ni-Alubronze ASTM B148-C95800
Stem Alu Bronze ASTM B150-C63200
Seat PTFE
Seat Retainer (> DN200) Alu Bronze ASTM B150-C63200
Dimensions [mm]
DN ød øD øC n x øh L H W
1/2” DN15 13 90 60.3 4-15.9 108 99 125
3/4” DN20 19 100 69.8 4-15.9 117 103 125
1” DN25 25 110 79.4 4-15.9 127 114 155
1 1/2” DN40 38 125 98.4 4-15.9 165 139 230
2” DN50 51 150 120.7 4-19.1 178 149 230
2 1/2” DN65 64 180 139.7 4-19.1 190 155 350
3” DN80 76 190 152.4 4-19.1 203 170 350
4” DN100 102 190 190.5 8-19.1 229 190 450
5” * DN125 127 255 215.9 8-22.2 356 316 ø 400
6” * DN150 152 280 241.3 8-22.2 394 336 ø 400
8” * DN200 203 345 298.5 8-22.2 457 420 ø 500
10” * DN250 254 405 362.0 12-25.4 533 396 ø 500
12” * DN300 305 485 431.8 12-25.4 610 417 ø 500
14” * DN350 334 535 476.3 12-28.6 686 458 ø 500
16” * DN400 385 595 539.8 16-28.6 762 456 ø 710
18” * DN450 436 635 577.9 16-31.8 864 565 ø 710
20” * DN500 487 700 635.0 20-31.8 914 620 ø 710
24” * DN600 589 815 749.3 20-34.9 1067 724 ø 800
* = With Gear Operator
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175** 200 225 250 260 °C
1/2”-24” 150# 13.4 12.5 10.5 9.9 9.7 9.7 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 150#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
** PTFE seated valves are limited to maximum +175°C
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 31
Fig. 7236-C958
A
N
S
I Full Bore, Split Body, 300#
Ball Valves
NAB (Ni-Alubronze)
Flanged
Full Bore
≤ DN200 (Floating Ball)
> DN200 (Trunion mounted Ball)
Description Ni-Alubronze ball valve, flanged ends (Flat Faced), 2 piece body, (<DN250) floating ball,
(≥DN250) trunion mounted ball, Full Bore (FB), PTFE seated, anti-static device, blow-out
proof stem, gland packing, ISO 5211 mounting table, Fire Safe, pressure class 300#.
Design Generally in accordance with API 6D, ISO 14313, ASME B16.24
Body, bonnet castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 6D, API 598, Fire Safe tested and certified to API 607
Face to Face In accordance with ASME B16.10:2000 Table 2 Column 7
Flange Dimensions In accordance with ASME B16.5-Class 300# (Flat Faced)
Pressure Rating In accordance with ASME B16.24-Class 300#*
Temperature Range -29°C to +175°C (PTFE seated valves are limited to max. +175°C**)
Options - In other ASTM B148 material grades (Suffix C...) and in other bronze materials
- With Monel Trim (Suffix MON)
- With other flanged connections DIN, JIS etc.
- With other seat materials
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 6D, ISO 14313
Materials
Parts Description Figure 7236-C958
Body and Cap Cast Ni-Alubronze ASTM B148-C95800
Ball ≤ DN100 : Alu Bronze ASTM B150-C63200
> DN100 : Cast Ni-Alubronze ASTM B148-C95800
Stem Alu Bronze ASTM B150-C63200
Seat PTFE
Seat Retainer (> DN200) Alu Bronze ASTM B150-C63200
Dimensions [mm]
DN ød øD øC n x øh L H W
1/2” DN15 13 95 66.7 4-15.9 140 99 200
3/4” DN20 19 117 82.5 4-19.1 152 103 200
1” DN25 25 123 88.9 4-19.1 165 114 240
1 1/2” DN40 38 155 114.0 4-22.2 190 139 350
2” DN50 51 165 127.0 8-19.1 216 149 350
2 1/2” DN65 64 190 149.2 8-22.2 241 152 400
3” DN80 76 210 168.3 8-22.2 282 170 400
4” DN100 102 255 200.0 8-22.2 305 206 500
5” * DN125 127 280 234.9 8-22.2 381 358 ø 450
6” * DN150 152 320 269.9 12-22.2 403 378 ø 450
8” * DN200 203 380 330.2 12-25.4 502 378 ø 550
10” * DN250 252 445 387.4 16-28.6 568 420 ø 500
12” * DN300 303 520 450.8 16-31.8 648 418 ø 500
14” * DN350 337 585 514.4 20-31.8 762 625 ø 560
16” * DN400 387 650 571.5 20-34.9 838 670 ø 560
18” * DN450 438 710 628.6 24-34.9 914 698 ø 630
20” * DN500 489 775 685.8 24-34.9 991 840 ø 630
24” * DN600 591 915 812.8 24-41.2 1143 1050 ø 710
* = With Gear Operator
Pressure and Temperature Range [Barg/°C]
DN Press
Class
Pressure / Temperature Rating to ASME B16.24* [Barg / °C]
-29/38 50 100 125 150 175** 200 225 250 260 °C
1/2”-24” 300# 35.6 33.0 27.4 26.3 25.5 25.2 Barg
* Above P-T table is extracted from ASME B16.24 material ASTM B148 Grade C95200, class 300#
Please note that GVC uses Ni-Alubronze B148 Grade C95800 which has better mechanical properties compared to ASTM B148 Grade C95200
** PTFE seated valves are limited to maximum +175°C
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 32
Series CWR-C958
A
N
S
I Replaceable Rubber Liner, 150#
Butterfly Valves, Rubber Lined
NAB (Ni-Alubronze)
Wafer
≤ DN200
> DN200
Description Ni-Alubronze concentric rubber lined butterfly valve, wafer type, pinned disc, 1 piece shaft,
replaceable rubber liner, triple sealing system, direct mount ISO 5211 mounting table,
pressure class 150#, bi-directional tight shut-off.
Materials
Parts Description Series CWR-C958
Body Cast Ni-Alubronze ASTM B148-C95800
Disc Cast Ni-Alubronze ASTM B148-C95800
Stem, Pins Stainless Steel 316, Monel or Duplex
Seat NBR, EPDM or Viton
Dimensions [mm]
DN L H1 H2 H3 Stem
SQ (◊) ISO
5211 Appr.
weight
2” DN50 43 55 128 33 9 F07 7 Kg
2 1/2” DN65 46 66 140 33 9 F07 8 Kg
3” DN80 46 75 150 33 9 F07 8 Kg
4” DN100 52 95 165 33 12 F07 9 Kg
5” DN125 56 115 178 33 12 F07 11 Kg
6” DN150 56 130 190 33 12 F07 13 Kg
8” DN200 60 155 230 50 17 F10 17 Kg
10” DN250 68 215 270 50 17 F10 24 Kg
12” DN300 78 251 310 50 22 F10 36 Kg
14” DN350 78 270 335 50 27 F10 58 Kg
16” DN400 102 325 370 60 27 F14 91 Kg
18” DN450 114 347 390 60 27 F14 102 Kg
20” DN500 127 383 420 60 36 F16 145 Kg
For larger sizes up to DN1200 see Series CSR-C958 (Semi Lug Type)
øC n-h
120.5 2-19.1
139.5 2-19.1
152.4 2-19.1
190.5 2-19.1
216.0 2-22.2
241.5 2-22.2
298.5 2-22.2
362.0 4-25.4
432.0 4-25.4
476.0 4-28.6
539.5 4-28.6
578.0 4-31.8
635.0 4-31.8
Design Generally in accordance with API 609 Category A
Body castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 609, API 598
Face to Face In accordance with API 609 Table 1
Flange Dimensions Suitable for mounting between flanges in accord. with ASME B16.5-Class 150#
Pressure Rating CWP 16 barg*
Temperature Range NBR -10°C to +100°C, EPDM -15°C to +120°C, Viton- 15°C to +230°C
Options - With body in other ASTM B148 material grades (Suffix C...)
- With liner Vulcanized onto the valve body (Suffix V)
- With other liner, disc and stem materials
- With manual operator (Hand Lever, Gearbox)
- With Hydraulic, electric and pneumatic actuators and accessories
- Suitable for mounting between flanges to DIN, JIS etc.
Technical Features
Marking In accordance with API 609, MSS SP-25
Type Approvals Type approvals from ABS, BV, CCS, DNV, GL, KR, LRS and RMRS
Other Approvals CE-PED, GOST and UL
Pressure and Temperature Range [Barg/°C]
Size Range (DN) Size Range (Inch) Pressure Class CWP (Cold Working Pressure) Rating *
DN 50 ~ DN 500 2” ~ 20” ASME Class 150# 16 barg
* Above CWP is the manufacturers standard value
Please note that connecting flanges might be subject to the PT-rating of ASME B16.24
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 33
Series CSR-C958
A
N
S
I Replaceable Rubber Liner, 150#
Butterfly Valves, Rubber Lined
NAB (Ni-Alubronze)
Semi-Lug
Description Ni-Alubronze concentric rubber lined butterfly valve, semi lug type, pinned disc, 1 piece
shaft, replaceable rubber liner, triple sealing system, direct mount ISO 5211 mounting
table, pressure class 150#, bi-directional tight shut-off.
Design Generally in accordance with API 609 Category A
Body castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 609, API 598
Face to Face In accordance with API 609 Table 1
Flange Dimensions Suitable for mounting between flanges in accord. with ASME B16.5-Class 150#
Pressure Rating CWP 16 barg (DN50~DN1000), CWP 10 barg (>DN1000) *
Temperature Range NBR -10°C to +100°C, EPDM -15°C to +120°C, Viton- 15°C to +230°C
Options - With body in other ASTM B148 material grades (Suffix C...)
- With liner Vulcanized onto the valve body (Suffix V)
- With other liner, disc and stem materials
- With manual operator (Hand Lever, Gearbox)
- With Hydraulic, electric and pneumatic actuators and accessories
- Suitable for mounting between flanges to DIN, JIS etc.
Technical Features
Marking In accordance with API 609, MSS SP-25
Type Approvals Type approvals from ABS, BV, CCS, DNV, GL, KR, LRS and RMRS
Other Approvals CE-PED, GOST and UL
Materials
Parts Description Series CSR-C958
Body, Disc Cast Ni-Alubronze ASTM B148-C95800
Stem, Pins Stainless Steel 316, Monel or Duplex
Seat NBR, EPDM or Viton
Dimensions [mm]
DN * L H1 H2 H3
Stem
(◊)
Stem
SQ (◊) H3 **
Stem
(ø)
Stem
**
Dia. (ø)
Key **
Size ISO
521
1
Appr.
weight
2” DN50 43 55 128 33 ◊ 9 33 ø 14 5x5 F07 10 Kg
2 1/2” DN65 46 66 140 33 ◊ 9 33 ø 14 5x5 F07 11 Kg
3” DN80 46 75 150 33 ◊ 9 33 ø 14 5x5 F07 11 Kg
4” DN100 52 95 165 33 ◊ 12 33 ø 19 6x6 F07 12 Kg
5” DN125 56 115 178 33 ◊ 12 33 ø 19 6x6 F07 13 Kg
6” DN150 56 130 190 33 ◊ 12 33 ø 19 6x6 F07 15 Kg
8” DN200 60 155 230 50 ◊ 17 50 ø 22 8x7 F10 19 Kg
10” DN250 68 215 270 50 ◊ 17 50 ø 25 8x7 F10 37 Kg
12” DN300 78 251 310 50 ◊ 22 50 ø 32 10x8 F10 47 Kg
14” DN350 78 270 335 50 ◊ 27 50 ø 32 10x8 F10 67 Kg
16” DN400 102 325 370 60 ◊ 27 60 ø 40 12x8 F14 91 Kg
18” DN450 114 347 390 60 ◊ 27 60 ø 40 12x8 F14 104 Kg
20” DN500 127 383 420 80 ◊ 36 80 ø 45 14x9 F16 154 Kg
24” DN600 154 453 495 80 ◊ 50 80 ø 65 20x12 F16 240 Kg
28” DN700 165 515 555 80 ◊ 50 80 ø 65 20x12 F16 305 Kg
32” DN800 160 592 640 -- -- 90 ø 65 20x12 F25 403 Kg
36” DN900 203 658 700 -- -- 130 ø 80 22x14 F25 607 Kg
40” DN1000 216 725 770 -- -- 150 ø 95 25x14 F30 829 Kg
44” DN1100 240 760 830 -- -- 150 ø 95 25x14 F30 1031 Kg
48” DN1200 254 840 890 -- -- 150 ø 95 25x14 F30 1212 Kg
* : DN550, DN650, DN750 and DN850 are available on request ** : Round stem with key also available
øC n-h (Tap)
120.5 4-5/8”
139.5 4-5/8”
152.4 4-5/8”
190.5 4-5/8”
216.0 4-3/4”
241.5 4-3/4”
298.5 4-3/4”
362.0 4-7/8”
432.0 4-7/8”
476.0 4-1”
539.5 4-1”
578.0 4-1 1/8”
635.0 4-1 1/8”
749.5 4-1 1/4”
863.5 4-1 3/8”
978.0 4-1 5/8”
1086.0 4-1 5/8”
1200.0 4-1 5/8”
1314.5 4-1 5/8”
1422.4 4-1 5/8”
Pressure and Temperature Range [Barg/°C]
Size Range (DN) Size Range (Inch) Pressure Class CWP (Cold Working Pressure) Rating *
DN 50 ~ DN 1000 2” ~ 40” ASME Class 150# 16 barg
* Above CWP is the manufacturers standard value
Please note that connecting flanges might be subject to the PT-rating of ASME B16.24
> DN 1000 > 40” ASME Class 150# 10 barg
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 34
Series CLR-C958
A
N
S
I Replaceable Rubber Liner, 150#
Butterfly Valves, Rubber Lined
NAB (Ni-Alubronze)
Lug
Description Ni-Alubronze concentric rubber lined butterfly valve, lug type, pinned disc, 1 piece shaft,
replaceable rubber liner, triple sealing system, direct mount ISO 5211 mounting table,
pressure class 150#, bi-directional tight shut-off.
Design Generally in accordance with API 609 Category A
Body castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 609, API 598
Face to Face In accordance with API 609 Table 1
Flange Dimensions Suitable for mounting between flanges in accord. with ASME B16.5-Class 150#
Pressure Rating CWP 16 barg (DN50~DN1000), CWP 10 barg (>DN1000) *
Temperature Range NBR -10°C to +100°C, EPDM -15°C to +120°C, Viton- 15°C to +230°C
Options - With body in other ASTM B148 material grades (Suffix C...)
- With liner Vulcanized onto the valve body (Suffix V)
- With other liner, disc and stem materials
- With manual operator (Hand Lever, Gearbox)
- With Hydraulic, electric and pneumatic actuators and accessories
- Suitable for mounting between flanges to DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 609, MSS SP-25
Type Approvals Type approvals from ABS, BV, CCS, DNV, GL, KR, LRS and RMRS
Other Approvals CE-PED, GOST and UL
Materials
Parts Description Series CLR-C958
Body, Disc Cast Ni-Alubronze ASTM B148-C95800
Stem, Pins Stainless Steel 316, Monel or Duplex
Seat NBR, EPDM or Viton
Dimensions [mm]
DN * L H1 H2 H3
Stem (◊) Stem
SQ (◊) H3 **
Stem (ø) Stem **
Dia. (ø) Key **
Size ISO
5211 Appr.
weight
2” DN50 43 55 128 33 ◊ 9 33 ø 14 5x5 F07 10 Kg
2 1/2” DN65 46 66 140 33 ◊ 9 33 ø 14 5x5 F07 11 Kg
3” DN80 46 75 150 33 ◊ 9 33 ø 14 5x5 F07 13 Kg
4” DN100 52 95 165 33 ◊ 12 33 ø 19 6x6 F07 15 Kg
5” DN125 56 115 178 33 ◊ 12 33 ø 19 6x6 F07 20 Kg
6” DN150 56 130 190 33 ◊ 12 33 ø 19 6x6 F07 22 Kg
8” DN200 60 155 230 50 ◊ 17 50 ø 22 8x7 F10 31 Kg
10” DN250 68 215 270 50 ◊ 17 50 ø 25 8x7 F10 47 Kg
12” DN300 78 251 310 50 ◊ 22 50 ø 32 10x8 F10 59 Kg
14” DN350 78 270 335 50 ◊ 27 50 ø 32 10x8 F10 85 Kg
16” DN400 102 325 370 60 ◊ 27 60 ø 40 12x8 F14 130 Kg
18” DN450 114 347 390 60 ◊ 27 60 ø 40 12x8 F14 154 Kg
20” DN500 127 383 420 80 ◊ 36 80 ø 45 14x9 F16 270 Kg
24” DN600 154 453 495 80 ◊ 50 80 ø 65 20x12 F16 314 Kg
28” DN700 165 515 555 80 ◊ 50 80 ø 65 20x12 F16 389 Kg
32” DN800 160 592 640 -- -- 90 ø 65 20x12 F25 597 Kg
36” DN900 203 658 700 -- -- 130 ø 80 22x14 F25 956 Kg
40” DN1000 216 725 770 -- -- 150 ø 95 25x14 F30 1209 Kg
44” DN1100 240 760 830 -- -- 150 ø 95 25x14 F30 1753 Kg
48” DN1200 254 840 890 -- -- 150 ø 95 25x14 F30 2053 Kg
* : DN550, DN650, DN750 and DN850 are available on request ** : Round stem with key also available
øC n-h
(Tap)
120.5 4-5/8”
139.5 4-5/8”
152.4 4-5/8”
190.5 8-5/8”
216.0 8-3/4”
241.5 8-3/4”
298.5 8-3/4”
362.0 12-7/8”
432.0 12-7/8”
476.0 12-1”
539.5 16-1”
578.0 16-1 1/8”
635.0 20-1 1/8”
749.5 20-1 1/4”
863.5 28-1 3/8”
978.0 28-1 5/8”
1086.0 32-1 5/8”
1200.0 36-1 5/8”
1314.5 40-1 5/8”
1422.4 44-1 5/8”
Pressure and Temperature Range [Barg/°C]
Size Range (DN) Size Range (Inch) Pressure Class CWP (Cold Working Pressure) Rating *
DN 50 ~ DN 1000 2” ~ 40” ASME Class 150# 16 barg
* Above CWP is the manufacturers standard value
Please note that connecting flanges might be subject to the PT-rating of ASME B16.24
> DN 1000 > 40” ASME Class 150# 10 barg
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 35
Series CFR-C958
A
N
S
I Replaceable Rubber Liner, 150#
Butterfly Valves, Rubber Lined
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze concentric rubber lined butterfly valve, double flanged type, pinned disc,
1 piece shaft, replaceable rubber liner, triple sealing system, direct mount ISO 5211
mounting table, pressure class 150#, bi-directional tight shut-off.
Design Generally in accordance with API 609 Category A
Body castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 609, API 598
Face to Face In accordance with manufacturers standard, see below dimensions table
Flange Dimensions Suitable for mounting between flanges in accord. with ASME B16.5-Class 150#
Pressure Rating CWP 16 barg (DN50~DN1000), CWP 10 barg (>DN1000) *
Temperature Range NBR -10°C to +100°C, EPDM -15°C to +120°C, Viton- 15°C to +230°C
Options - With body in other ASTM B148 material grades (Suffix C...)
- With liner Vulcanized onto the valve body (Suffix V)
- With f to f dimensions to API609 Table 2 short pattern (Vulcanized liner only)
- With other liner, disc and stem materials
- With manual operator (Hand Lever, Gearbox)
- With Hydraulic, electric and pneumatic actuators and accessories
- Suitable for mounting between flanges to DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 609, MSS SP-25
Type Approvals Type approvals from ABS, BV, CCS, DNV, GL, KR, LRS and RMRS
Other Approvals CE-PED, GOST and UL
Materials
Parts Description Series CFR-C958
Body, Disc Cast Ni-Alubronze ASTM B148-C95800
Stem, Pins Stainless Steel 316, Monel or Duplex
Seat NBR, EPDM or Viton
Dimensions [mm]
DN * L H1 H2 H3
Stem (◊) Stem
SQ (◊) H3 **
Stem (ø) Stem**
Dia. (ø) Key**
Size ISO
5211 Appr.
weight
2” DN50 40 88 128 33 ◊ 9 33 ø 14 5x5 F07 14 Kg
2 1/2” DN65 40 98 140 33 ◊ 9 33 ø 14 5x5 F07 14 Kg
3” DN80 60 105 150 33 ◊ 9 33 ø 14 5x5 F07 16 Kg
4” DN100 60 120 165 33 ◊ 12 33 ø 19 6x6 F07 22 Kg
5” DN125 100 140 178 33 ◊ 12 33 ø 19 6x6 F07 29 Kg
6” DN150 100 165 190 33 ◊ 12 33 ø 19 6x6 F07 35 Kg
8” DN200 100 190 230 50 ◊ 17 50 ø 22 8x7 F10 47 Kg
10” DN250 110 215 270 50 ◊ 17 50 ø 25 8x7 F10 66 Kg
12” DN300 110 251 310 50 ◊ 22 50 ø 32 10x8 F10 78 Kg
14” DN350 120 270 335 50 ◊ 27 50 ø 32 10x8 F10 100 Kg
16” DN400 130 325 370 60 ◊ 27 60 ø 40 12x8 F14 147 Kg
18” DN450 150 347 390 60 ◊ 27 60 ø 40 12x8 F14 174 Kg
20” DN500 160 383 420 80 ◊ 36 80 ø 45 14x9 F16 222 Kg
24” DN600 170 453 495 80 ◊ 50 80 ø 65 20x12 F16 323 Kg
28” DN700 180 515 555 80 ◊ 50 80 ø 65 20x12 F16 415 Kg
32” DN800 200 592 640 -- -- 90 ø 65 20x12 F25 599 Kg
36” DN900 230 658 700 -- -- 130 ø 80 22x14 F25 854 Kg
40” DN1000 250 725 770 -- -- 150 ø 95 25x14 F30 1071 Kg
44” DN1100 280 760 830 -- -- 150 ø 95 25x14 F30 1240 Kg
48” DN1200 300 840 890 -- -- 150 ø 95 25x14 F30 1553 Kg
* : DN550, DN650, DN750, DN850 and DN1300~DN4000 are available on request ** : Round stem with key also available
øC n-h
(Tap)
120.5 4-5/8”
139.5 4-5/8”
152.4 4-5/8”
190.5 4-5/8”
216.0 4-3/4”
241.5 4-3/4”
298.5 4-3/4”
362.0 4-7/8”
432.0 4-7/8”
476.0 4-1”
539.5 4-1”
578.0 4-1 1/8”
635.0 4-1 1/8”
749.5 4-1 1/4”
863.5 4-1 3/8”
978.0 4-1 5/8”
1086.0 4-1 5/8”
1200.0 4-1 5/8”
1314.5 4-1 5/8”
1422.4 4-1 5/8”
n-h
(ø)
--
--
--
4-19.1
4-19.1
4-19.1
4-19.1
8-22.2
8-22.2
8-25.4
12-25.4
12-28.6
16-28.6
16-31.8
24-34.9
24-41.3
28-41.3
32-41.3
36-41.3
40-41.3
Pressure and Temperature Range [Barg/°C]
Size Range (DN) Size Range (Inch) Pressure Class CWP (Cold Working Pressure) Rating *
DN 50 ~ DN 1000 2” ~ 40” ASME Class 150# 16 barg
* Above CWP is the manufacturers standard value
Please note that connecting flanges might be subject to the PT-rating of ASME B16.24
> DN 1000 > 40” ASME Class 150# 10 barg
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 36
Series
HWT-C958 FHW-C958
MHW-C958 HWR-C958
A
N
S
I 150#
Butterfly Valves, High Performance
NAB (Ni-Alubronze)
Wafer
Description Ni-Alubronze double eccentric High Performance butterfly valve, wafer type, pinned disc,
1 piece blow out proof shaft, Rubber / (R)PTFE / Fire Safe and metal seated, adjustable
gland packing, direct mount ISO 5211 mounting table, pressure class 150#, bi-directional
tight shut-off.
Seat Types - Series HWT-C958 : PTFE seated
- Series FHW-C958 : Fire Safe seated PTFE + Monel metal backup ring
- Series MHW-C958 : Monel metal seated [Not tight shut-off]
- Series HWR-C958 : Rubber seated NBR, EPDM or Viton
Design Generally in accordance with API 609 Category B
Body castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 609, API 598
Face to Face In accordance with API 609 Table 2 - Lug- and Wafer-Type Class 150#
Flange Dimensions Suitable for mounting between flanges in accord. with ASME B16.5-Class 150#
Pressure Rating In accordance with ASME B16.34 Appendix B
Temperature Range PTFE, RTFE and Fire-Safe seat : -29°C to + 204°C
Metal Seated : -29°C to + 260°C **
Rubber Seated : Depending on material, please consult us **
Options - In pressure class 300#
- With body in other ASTM B148 material grades (Suffix C...)
- With other disc and stem materials
- With RTFE seat (instead of PTFE seat)
- With other material metal backup ring and metal seat (Monel, Hastelloy)
- With manual operator (Hand Lever, Gearbox)
- With Hydraulic, electric and pneumatic actuators and accessories
- Suitable for mounting between flanges to DIN, JIS etc.
Technical Features
Marking In accordance with API 609, MSS SP-25
Type Approvals Type approvals from ABS, BV, CCS, DNV, GL, KR, LRS and RMRS
Other Approvals CE-PED, GOST, UL and API 607 fire safe certified (With Fire Safe seat)
Materials
Parts Description Series HWR/HWT/MHW/FHW-C958
Body, Disc Cast Ni-Alubronze ASTM B148-C95800
Retainer Ring Ni-Alubronze
Stem, Pins Monel
Seat See above “DESCRIPTION”
Dimensions [mm]
DN øC n-h L H H1 H2 H4
Stem (◊) Stem
SQ (◊) H3 *
Stem (ø) Stem *
ød Key *
Size ISO
5211 Appr.
weight
2” DN50 120.5 2-19.1 43 331 118 168 33 ◊ 12 45 ø 16 5x5 F07 4.5 Kg
2 1/2” DN65 139.5 2-19.1 46 355 133 177 33 ◊ 12 45 ø 16 5x5 F07 5.5 Kg
3” DN80 152.5 2-19.1 48 374 144 185 33 ◊ 12 45 ø 19 6x6 F07 9.0 Kg
4” DN100 190.5 2-19.1 54 409 164 200 33 ◊ 12 45 ø 19 6x6 F07 10.0 Kg
5” DN125 216.0 2-22.2 57 450 188 217 33 ◊ 12 45 ø 19 6x6 F07 13.0 Kg
6” DN150 241.5 2-22.2 57 490 205 240 33 ◊ 12 45 ø 19 6x6 F07 17.0 Kg
8” DN200 298.5 2-22.2 64 553 223 270 55 ◊ 17 60 ø 25 8x7 F10 26.0 Kg
10” DN250 362.0 2-25.4 71 655 275 320 55 ◊ 22 60 ø 25 8x7 F10 40.0 Kg
* : Round stem with key also available
Pressure and Temperature Range [Barg/°C]
DN Press
Class Seat
Pressure/Temperature Rating to ASME B16.34 Appendix B *
[Barg/°C]
-29/40 +50 +100 +150 +200 +204 °C
2”-10” 150# PTFE 19.00 18.00 15.75 14.00 13.00 12.90 Barg
* Please note that connecting bronze flanges might be subject to the ratings of ASME B16.24
** P-T ratings for metal seated and rubber seated valves are available on request
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 37
Series
HST-C958 FHS-C958
MHS-C958 HSR-C958
A
N
S
I 150#
Butterfly Valves, High Performance
NAB (Ni-Alubronze)
Semi-Lug
Description Ni-Alubronze double eccentric High Performance butterfly valve, semi lug type, pinned disc, 1 piece blow out proof shaft,
Rubber / (R)PTFE / Fire Safe and metal seated, adjustable gland packing, direct mount ISO 5211 mounting table, pressure
class 150#, bi-directional tight shut-off.
Seat Types - Series HST-C958 : PTFE seated
- Series FHS-C958 : Fire Safe seated PTFE + Monel metal backup ring
- Series MHS-C958 : Monel metal seated [Not tight shut-off]
- Series HSR-C958 : Rubber seated NBR, EPDM or Viton
Design Generally in accordance with API 609 Category B
Body castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 609, API 598
Face to Face In accordance with API 609 Table 2 - Lug- and Wafer-Type Class 150#
Flange Dimensions Suitable for mounting between flanges in accord. with ASME B16.5-Class 150#
Pressure Rating In accordance with ASME B16.34 Appendix B
Temperature Range PTFE, RTFE and Fire-Safe seat : -29°C to + 204°C
Metal Seated : -29°C to + 260°C **
Rubber Seated : Depending on material, please consult us **
Options - In pressure class 300#
- With body in other ASTM B148 material grades (Suffix C...)
- With other disc and stem materials
- With RTFE seat (instead of PTFE seat)
- With other material metal backup ring and metal seat (Monel, Hastelloy)
- With manual operator (Hand Lever, Gearbox)
- With Hydraulic, electric and pneumatic actuators and accessories
- Suitable for mounting between flanges to DIN, JIS etc.
Technical Features
Marking In accordance with API 609, MSS SP-25
Type Approvals Type approvals from ABS, BV, CCS, DNV, GL, KR, LRS and RMRS
Other Approvals CE-PED, GOST, UL and API 607 fire safe certified (With Fire Safe seat)
Materials
Parts Description Series HSR/HST/MHS/FHS-C958
Body, Disc Cast Ni-Alubronze ASTM B148-C95800
Retainer Ring Ni-Alubronze
Stem, Pins Monel
Seat See above “DESCRIPTION”
Dimensions [mm]
DN * øC n-h L H H1 H2 H4
Stem (◊) Stem
SQ (◊) H3 **
Stem (ø) Stem **
ød Key **
Size ISO
5211 Appr.
weight
2” DN50 120.5 4-3/4” 43 331 118 168 33 ◊ 12 45 ø 16 5x5 F07 5.0 Kg
2 1/2” DN65 139.5 4-3/4” 46 355 133 177 33 ◊ 12 45 ø 16 5x5 F07 6.5 Kg
3” DN80 152.5 4-3/4” 48 374 144 185 33 ◊ 12 45 ø 19 6x6 F07 10.5 Kg
4” DN100 190.5 4-3/4” 54 409 164 200 33 ◊ 12 45 ø 19 6x6 F07 15 Kg
5” DN125 216.0 4-7/8” 57 450 188 217 33 ◊ 12 45 ø 19 6x6 F07 18 Kg
6” DN150 241.5 4-7/8” 57 490 205 240 33 ◊ 12 45 ø 19 6x6 F07 25 Kg
8” DN200 298.5 4-7/8” 64 553 223 270 55 ◊ 17 60 ø 25 8x7 F10 36 Kg
10” DN250 362.0 4-1” 71 655 275 320 55 ◊ 22 60 ø 25 8x7 F10 56 Kg
12” DN300 432.0 4-1” 81 718 308 350 55 ◊ 27 60 ø 32 10x8 F10 68 Kg
14” DN350 476.0 4-1 1/8” 92 816 346 395 65 ◊ 27 75 ø 38 12x8 F14 93 Kg
16” DN400 539.5 4-1 1/8” 102 905 385 445 65 ◊ 27 75 ø 38 12x8 F14 121 Kg
18” DN450 578.0 4-1 1/4” 114 1000 410 490 90 ◊ 36 100 ø 50 14x9 F16 144 Kg
20” DN500 635.0 4-1 1/4” 127 1048 448 500 90 ◊ 36 100 ø 50 14x9 F16 160 Kg
24” DN600 749.3 4-1 3/8” 154 1180 515 565 90 ◊ 50 100 ø 65 20x12 F16 284 Kg
28” DN700 863.6 4-1 3/8” 165 1346 596 650 -- -- 100 ø 65 20x12 F25 388 Kg
32” DN800 977.9 4-1 5/8” 190 1515 645 720 -- -- 150 ø 80 22x14 F30 607 Kg
36” DN900 1085.8 4-1 5/8” 203 1665 710 805 -- -- 150 ø 85 22x14 F30 860 Kg
40” DN1000 1200.2 4-1 5/8” 216 1815 770 870 -- -- 175 ø 100 28x16 F35 1180 Kg
* : DN550, DN650, DN750 an larger sizes DN1100~DN1500 available on request ** : Round stem with key also available
Pressure and Temperature Range [Barg/°C]
DN Press
Class Seat
Pressure/Temperature Rating to ASME B16.34 Appendix B *
[Barg/°C]
-29/40 +50 +100 +150 +200 +204 °C
2”-60” 150# PTFE 19.00 18.00 15.75 14.00 13.00 12.90 Barg
* Please note that connecting bronze flanges might be subject to the ratings of ASME B16.24
** P-T ratings for metal seated and rubber seated valves are available on request
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 38
Series
HLT-C958 FHL-C958
MHL-C958 HLR-C958
A
N
S
I 150#
Butterfly Valves, High Performance
NAB (Ni-Alubronze)
Lug
Description Ni-Alubronze double eccentric High Performance butterfly valve, lug type, pinned disc, 1 piece blow out proof shaft,
Rubber / (R)PTFE / Fire Safe and metal seated, adjustable gland packing, direct mount ISO 5211 mounting table, pressure
class 150#, bi-directional tight shut-off.
Seat Types - Series HLT-C958 : PTFE seated
- Series FHL-C958 : Fire Safe seated PTFE + Monel metal backup ring
- Series MHL-C958 : Monel metal seated [Not tight shut-off]
- Series HLR-C958 : Rubber seated NBR, EPDM or Viton
Design Generally in accordance with API 609 Category B
Body castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 609, API 598
Face to Face In accordance with API 609 Table 2 - Lug- and Wafer-Type Class 150#
Flange Dimensions Suitable for mounting between flanges in accord. with ASME B16.5-Class 150#
Pressure Rating In accordance with ASME b16.34 Appendix B
Temperature Range PTFE, RTFE and Fire-Safe seat : -29°C to + 204°C
Metal Seated : -29°C to + 260°C **
Rubber Seated : Depending on material, please consult us **
Options - In pressure class 300#
- With body in other ASTM B148 material grades (Suffix C...)
- With other disc and stem materials
- With RTFE seat (instead of PTFE seat)
- With other material metal backup ring and metal seat (Monel, Hastelloy)
- With manual operator (Hand Lever, Gearbox)
- With Hydraulic, electric and pneumatic actuators and accessories
- Suitable for mounting between flanges to DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 609, MSS SP-25
Type Approvals Type approvals from ABS, BV, CCS, DNV, GL, KR, LRS and RMRS
Other Approvals CE-PED, GOST, UL and API 607 fire safe certified (With Fire Safe seat)
Materials
Parts Description Series HLR/HLT/MHL/FHL-C958
Body, Disc Cast Ni-Alubronze ASTM B148-C95800
Retainer Ring Ni-Alubronze
Stem, Pins Monel
Seat See above “DESCRIPTION”
Dimensions [mm]
DN * øC n-h
(Tap) L H H1 H2 H4
Stem (◊) Stem
SQ (◊) H3 **
Stem (ø) Stem **
ød Key **
Size ISO
5211 Appr.
weight
2” DN50 120.5 4-3/4” 43 331 118 168 33 ◊ 12 45 ø 16 5x5 F07 8.0 Kg
2 1/2” DN65 139.5 4-3/4” 46 355 133 177 33 ◊ 12 45 ø 16 5x5 F07 9.0 Kg
3” DN80 152.5 4-3/4” 48 374 144 185 33 ◊ 12 45 ø 19 6x6 F07 12 Kg
4” DN100 190.5 8-3/4” 54 409 164 200 33 ◊ 12 45 ø 19 6x6 F07 15 Kg
5” DN125 216.0 8-7/8” 57 450 188 217 33 ◊ 12 45 ø 19 6x6 F07 20 Kg
6” DN150 241.5 8-7/8” 57 490 205 240 33 ◊ 12 45 ø 19 6x6 F07 29 Kg
8” DN200 298.5 8-7/8” 64 553 223 270 55 ◊ 17 60 ø 25 8x7 F10 44 Kg
10” DN250 362.0 12-1” 71 655 275 320 55 ◊ 22 60 ø 25 8x7 F10 65 Kg
12” DN300 432.0 12-1” 81 718 308 350 55 ◊ 27 60 ø 32 10x8 F10 80 Kg
14” DN350 476.0 12-1 1/8” 92 816 346 395 65 ◊ 27 75 ø 38 12x8 F14 130 Kg
16” DN400 539.5 16-1 1/8” 102 905 385 445 65 ◊ 27 75 ø 38 12x8 F14 144 Kg
18” DN450 578.0 16-1 1/4” 114 1000 410 490 90 ◊ 36 100 ø 50 14x9 F16 191 Kg
20” DN500 635.0 20-1 1/4” 127 1048 448 500 90 ◊ 36 100 ø 50 14x9 F16 226 Kg
24” DN600 749.3 20-1 3/8” 154 1180 515 565 90 ◊ 50 100 ø 65 20x12 F16 339 Kg
28” DN700 863.6 28-1 3/8” 165 1346 596 650 -- -- 100 ø 65 20x12 F25 519 Kg
32” DN800 977.9 28-1 5/8” 190 1515 645 720 -- -- 150 ø 80 22x14 F30 783 Kg
36” DN900 1085.8 32-1 5/8” 203 1665 710 805 -- -- 150 ø 85 22x14 F30 1102 Kg
40” DN1000 1200.2 36-1 5/8” 216 1815 770 870 -- -- 175 ø 100 28x16 F35 1450 Kg
* : DN550, DN650, DN750 an larger sizes DN1100~DN1500 available on request ** : Round stem with key also available
Pressure and Temperature Range [Barg/°C]
DN Press
Class Seat
Pressure/Temperature Rating to ASME B16.34 Appendix B *
[Barg/°C]
-29/40 +50 +100 +150 +200 +204 °C
2”-60” 150# PTFE 19.00 18.00 15.75 14.00 13.00 12.90 Barg
* Please note that connecting bronze flanges might be subject to the ratings of ASME B16.24
** P-T ratings for metal seated and rubber seated valves are available on request
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 39
Series
HFT-C958
FHF-C958
MHF-C958 HFR-C958
A
N
S
I 150#
Butterfly Valves, High Performance
NAB (Ni-Alubronze)
Flanged
Description Ni-Alubronze double eccentric High Performance butterfly valve, double flanged type, pinned disc, 1 piece blow out proof shaft,
Rubber / (R)PTFE / Fire Safe and metal seated, adjustable gland packing, direct mount ISO 5211 mounting table, pressure
class 150#, bi-directional tight shut-off.
Seat Types - Series HFT-C958 : PTFE seated
- Series FHF-C958 : Fire Safe seated PTFE + Monel metal backup ring
- Series MHF-C958 : Monel metal seated [Not tight shut-off]
- Series HFR-C958 : Rubber seated NBR, EPDM or Viton
Design Generally in accordance with API 609 Category B
Body castings from a Marine Class Society Approved Foundry on request
Testing In accordance with API 609, API 598
Face to Face In accordance with API 609 Table 2 (C) Double Flanged (Short Pattern) - Class 150#
Flange Dimensions Suitable for mounting between flanges in accord. with ASME B16.5-Class 150#
Pressure Rating In accordance with ASME B16.34 Appendix B
Temperature Range PTFE, RTFE and Fire-Safe seat : -29°C to + 204°C
Metal Seated : -29°C to + 260°C **
Rubber Seated : Depending on material, please consult us **
Options - In pressure class 300#
- With body in other ASTM B148 material grades (Suffix C...)
- With other disc and stem materials
- With RTFE seat (instead of PTFE seat)
- With other material metal backup ring and metal seat (Monel, Hastelloy)
- With manual operator (Hand Lever, Gearbox)
- With Hydraulic, electric and pneumatic actuators and accessories
- With other flanged connections to DIN, JIS etc.
- With Marine Class Inspection Certificate (EN10204-3.2) by ABS, BV, DNV, LRS
and other (Marine Class) Societies
Technical Features
Marking In accordance with API 609, MSS SP-25
Type Approvals Type approvals from ABS, BV, CCS, DNV, GL, KR, LRS and RMRS
Other Approvals CE-PED, GOST, UL and API 607 fire safe certified (With Fire Safe seat)
Materials
Parts Description Series HLR/HLT/MHL/FHL-C958
Body, Disc Cast Ni-Alubronze ASTM B148-C95800
Retainer Ring Ni-Alubronze
Stem, Pins Monel
Seat See above “DESCRIPTION”
Dimensions [mm]
DN * øC n-h
(Tap) L H H1 H2 H4
Stem (◊) Stem
SQ (◊) H3 **
Stem (ø) Stem **
ød Key **
Size ISO
5211 Appr.
weight
2” DN50 120.5 4-3/4” 43 331 118 168 33 ◊ 12 45 ø 16 5x5 F07 14 Kg
2 1/2” DN65 139.5 4-3/4” 46 355 133 177 33 ◊ 12 45 ø 16 5x5 F07 18 Kg
3” DN80 152.5 4-3/4” 48 374 144 185 33 ◊ 12 45 ø 19 6x6 F07 22 Kg
4” DN100 190.5 8-3/4” 54 409 164 200 33 ◊ 12 45 ø 19 6x6 F07 28 Kg
5” DN125 216.0 8-7/8” 57 450 188 217 33 ◊ 12 45 ø 19 6x6 F07 37 Kg
6” DN150 241.5 8-7/8” 57 490 205 240 33 ◊ 12 45 ø 19 6x6 F07 44 Kg
8” DN200 298.5 8-7/8” 64 553 223 270 55 ◊ 17 60 ø 25 8x7 F10 64 Kg
10” DN250 362.0 12-1” 71 655 275 320 55 ◊ 22 60 ø 25 8x7 F10 87 Kg
12” DN300 432.0 12-1” 81 718 308 350 55 ◊ 27 60 ø 32 10x8 F10 123 Kg
14” DN350 476.0 12-1 1/8” 92 816 346 395 65 ◊ 27 75 ø 38 12x8 F14 155 Kg
16” DN400 539.5 16-1 1/8” 102 905 385 445 65 ◊ 27 75 ø 38 12x8 F14 224 Kg
18” DN450 578.0 16-1 1/4” 114 1000 410 490 90 ◊ 36 100 ø 50 14x9 F16 255 Kg
20” DN500 635.0 20-1 1/4” 127 1048 448 500 90 ◊ 36 100 ø 50 14x9 F16 321 Kg
24” DN600 749.3 20-1 3/8” 154 1180 515 565 90 ◊ 50 100 ø 65 20x12 F16 475 Kg
28” DN700 863.6 28-1 3/8” 165 1346 596 650 -- -- 100 ø 65 20x12 F25 685 Kg
32” DN800 977.9 28-1 5/8” 190 1515 645 720 -- -- 150 ø 80 22x14 F30 1050 Kg
36” DN900 1085.8 32-1 5/8” 203 1665 710 805 -- -- 150 ø 85 22x14 F30 1350 Kg
40” DN1000 1200.2 36-1 5/8” 216 1815 770 870 -- -- 175 ø 100 28x16 F35 1720 Kg
* : DN550, DN650, DN750 an larger sizes DN1100~DN1500 available on request ** : Round stem with key also available
Pressure and Temperature Range [Barg/°C]
DN Press
Class Seat
Pressure/Temperature Rating to ASME B16.34 Appendix B *
[Barg/°C]
-29/40 +50 +100 +150 +200 +204 °C
2”-60” 150# PTFE 19.00 18.00 15.75 14.00 13.00 12.90 Barg
* Please note that connecting bronze flanges might be subject to the ratings of ASME B16.24
** P-T ratings for metal seated and rubber seated valves are available on request
Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve Center b.v.
www.globalvalvecenter.com 2015 Page 40
Ni-Alubronze
Valves
A
N
S
I
Global Valve Center B.V. Zwaalweg 14 2991 ZC Barendrecht The Netherlands
Tel 1 +31 (0) 180 39 89 38 Tel 2 +31 (0) 180 39 88 69 Fax +31 (0) 84 22 98 163
VALVE SPECIALISTS !