NIBE™ SMO 10 CONTROL MODULE NIBE SMO 10 SMO 10 is an intelligent control module that, together with one or more NIBE air/water heat pumps and existing heating and hot water equipment, creates a complete unit. The SMO 10 unit allows the heat pump to be docked to va- rious solutions such as eletric boiler, oil fired boiler and accu- mulator tank / water heater such as a NIBE VPA. SMO 10 controls up to nine air/water heat pumps (of which only one can be used for hot water), electric heater, circula- tion pump, mixing valve, etc. F2XXX works with floating con- densing against the heating system and prioritises hot water charging via the three way valve. BE IN CONTROL. • Advanced controller. • Gives optimised control of one or more air/water heat pumps and the existing heating installation. • Clear display, in your language, of the heat pump and heating system’s essential temperatures. • Prepared for docking of air/water heat pump to exhaust air heat pump. • Two heating systems, pool heating, step controlled extra heat source. • Emergency switch over prepared if controller breakdown or compressor failure. • Scheduling of room temperature / hot water / vacation
Transcript
NIBE™ SMO 10 CONtrOl MODUlE
NIBE SMO 10SMO 10 is an intelligent control module that, together with one or more NIBE air/water heat pumps and existing heating and hot water equipment, creates a complete unit.
the SMO 10 unit allows the heat pump to be docked to va-rious solutions such as eletric boiler, oil fired boiler and accu-mulator tank / water heater such as a NIBE VPA.
SMO 10 controls up to nine air/water heat pumps (of which only one can be used for hot water), electric heater, circula-tion pump, mixing valve, etc. F2XXX works with floating con-densing against the heating system and prioritises hot water charging via the three way valve.
Be in control.
• Advanced controller.
• Gives optimised control of one or more air/water heat pumps and the existing heating installation.
• Clear display, in your language, of the heat pump and heating system’s essential temperatures.
• Prepared for docking of air/water heat pump to exhaust air heat pump.
• two heating systems, pool heating, step controlled extra heat source.
• Emergency switch over prepared if controller breakdown or compressor failure.
• Scheduling of room temperature / hot water / vacation
2 NIBE SMO 10
LEK
LEK
LEK
Overview SMO 10
Table Compatible outdoor units
Max nr of heat pumps
Additional energy before or after three
way valve
Display outsi-de heat pump
room
Swimming pool
Step control of extra heat
source
Supervision of power load at house, fused controlled (3x400V)
Number of dockings
supported
Number of heating systems
supported
SMO 10F2026, F2016,
F2300
9 *
(1dhw)Both possible NO YES YES YES MANY ** 2
40540
6
151.5
328
276
64
937
38,1
Ø 6
405
406
151.5
328
276
64
937
38,1
Ø 6
Good to know aBout niBe™ SMo 10
Dimensions (mm)
Outdoor unitDomestic hot water
3-way valve Controller Energy back up Buffer vesselDouble jacket cylinder Coil cylinder
* Max 1 heat pump for domestic hot water.** NIBE SMO 10 can be connected in several different ways. Further option information is available at www.nibe.eu and in respective assembly instructions for the accessories used.
SMO 10
Oljepanna alternativt elpanna med shunt
POOL
VP2
VP1
Oil/Gas/Electrical boiler
SMO 10
VPA 300/200
F2XXX
F2XXX
inStallation
NIBE SMO 10 can be connected in several different ways. this is just an example of a docking. Further system solutions are available in respective assembly instructions for the accessories used.
See the appropriate “Installation and Maintenance Instructions” for more information.Note! this is an example diagram. Actual installations must be planned according to applicable standards.
Below is an example diagram showing the F2XXX together with SMO 10, additional heat, water heater, pool heating and additional F2XXX air/water heat pump.
SMO 10 controls up to nine F2XXX (of which only one can be used for hot water), additional heat, circulation pumps, shuttle valve, etc.
F2XXX HP1 prioritises hot water charging via a shuttle valve (19.1). If there are no hot water or heating demands, F2XXX is available for pool heating via shuttle valve (19.2).
F2XXX runs with floating condensing towards the heating system.
If F2XXX cannot handle the heating demand, the additional heat is connected.
When additional heat is engaged, hot water is heated using the immersion heater in the hot water heater.
the fan works in stage 1 or stage 2 depending on the outdoor air temperature.
In cases where the system volume in the radiator circuit is below 20 l/kW (heat pump output at 7/45 °C) and/or the radiator flow is choked uncontrolled, a UKV tank (120) is installed as a volume and flow increaser.
