Date post: | 21-Jan-2016 |
Category: |
Documents |
Upload: | augusta-oconnor |
View: | 218 times |
Download: | 1 times |
NLA-5 Series Rigging Manual
2015.12.01.
Preparation Material
2
ㄴ
Preparation Material- 1
3
1. Chain block or Electric
hoist
2. Shackle (over 5/8 inch)
3. Sling belt
12
3
ㄴ
Preparation Material - 2
4
1. FRONT BAR
2. BACK BAR
3. Bolt, Spring washer,
Flat washer
321
4. Bolt & Washer
Assembly
(Must use 2 washers)
4
ㄴ
Preparation Material - 3
5
21
1. Short bar is Back bar when connect
Frame → NLA-15S NLA-15S → NLA-5.
2. Long bar is Back bar when connect
NLA-5 → NLA-5.
ㄴ
Preparation Material - 4
6
1. Shackle (1/2 inch) 1EA
1
ㄴ
Preparation Material - 5
7
1. Electric Screw Driver
2. Hexagonal Tip (5mm)
3. Hexagonal
Wrench_Manual (5mm)
12
3
Chain block Connection
8
ㄴ
Chainblock Connection - 1
9
Like the above picture, connect a sling belt to a trus
s.
(When you install it to H-beam, lower circled 1 to
down side.)
1
ㄴ
Chainblock Connection - 2
10
Like the picture, assemble the sling belt hanger to the
shackle.
ㄴ
Chainblock Connection - 3
11
Connected sling belt and shackle
ㄴ
Chainblock Connection - 4
12
Connect hanger of chain block(or hoist) to shackle.
ㄴ
Chainblock Connection - 5
13Connected chain block / hoist
Frame Assembly
14
ㄴ
Frame Assembly - 1
15
1. NLA-15S2. NLA-5 FRAME
2
1
ㄴ
Frame Assembly - 2
16
Put NLA-5 FRAME on NLA-15S.
ㄴ
Frame Assembly - 3
17
Tighten up and down holes in FRONT BAR
with bolts.
ㄴ
Frame Assembly - 4
18
Adjust frame to make an alignment of
middle hole and the screw hole in the
frame.(1)
1
ㄴ
Frame Assembly - 5
19
Tighten them with a bolt.
(Use an electric screw driver for your
convenience)
ㄴ
Frame Assembly - 6
20
Connect rear side of the frame using short back
bar.
ㄴ
Frame Assembly - 7
21
Tighten whole points using manual
hexagonal wrench.
ㄴ
프레임 조립 - 8
22
Connected frame on NLA-15S
ㄴ
Frame Assembly - 9
23
Install ½ inch shackle to a preferred spot.
ㄴ
Frame Assembly - 10
24
Connect the shackle to the hanger of chain
block(or hoist).
NLA-5 Assembly
25
ㄴ
Speaker Assembly- 1
26
Lift up frame(1) with chain block, and put
one NLA-5(2) under the frame.
1
2
ㄴ Speaker Assembly - 2
27
Align front part of the speakers by
lowering the frame.
ㄴ
Speaker Assembly - 3
28
Firstly, tighten the up and down holes of F
RONT BAR with bolts.
ㄴ
Speaker Assembly - 4
29
Match middle hole in the bar and the speaker by
adjusting position of them.
ㄴ
Speaker Assembly - 5
30
Tighten the middle hole with bolts.
ㄴ
Speaker Assembly - 6
31
Connect the lower part of short back bar with
bolts.
ㄴ
Speaker Assembly - 7
32
Lift up the speaker with chain block, and
match up hole with speaker’s hole.
ㄴ
Speaker Assembly - 8
33
Connect the up hole with a bolt.
ㄴ
Speaker Assembly - 9
34
Completed 1 set of NLA-5
ㄴ
Speaker Assembly - 10
35
Put another NLA-5 below.
ㄴ
Speaker Assembly - 11
36
Align front part of NLA-5 using chain
block.
ㄴ
Speaker Assembly - 12
37
Connect the up and down hole in the FRO
NT BAR with bolts.
ㄴ
Speaker Assembly - 13
38
Match middle hole in the bar and the speaker by
adjusting position of them.
ㄴ
Speaker Assembly - 14
39
Tighten the middle hole with bolts.
ㄴ
Speaker Assembly - 15
40
Connect the downside of the long back
bar with bolts.
ㄴ
Speaker Assembly - 16
41
Rear part of NLA-5
5
0
10
Angles for each hole
ㄴ
Speaker Assembly - 17
42
You can see that this picture is set to 0
degree.
5
0
10
ㄴ
Speaker Assembly - 18
43
Choose your preferred angle
of hole using chain block.
The example in the photo is 0
degree.
ㄴ
Speaker Assembly - 19
44
Connect it with a bolt.
ㄴ
Speaker Assembly - 20
45
Completed 2 set of NLA-5
ㄴ
Speaker Assembly - 21
46
Fully completed figure after repeated
process.
NLA-5 RACK Assembly
47
ㄴ
Speaker Assembly- 1
48
Insert an amplifier to NLA-5 RACK.
ㄴ Speaker Assembly - 2
49
1. Fill up spaces with blank panel.
2. Connect power cable, speaker cable,
and LAN cable beforehand.
ㄴ Speaker Assembly - 3
50
Put NLA-5 FRAME on NLA-5 Rack.
ㄴ Speaker Assembly - 4
51
Tighten up and down holes in FRONT BAR
with bolts.
ㄴ Speaker Assembly - 5
52
Adjust frame to make an alignment of
middle hole and the screw hole in the
frame.(1)
1
ㄴ Speaker Assembly - 6
53
Tighten them with a bolt.
(Use an electric screw driver for your
convenience)
ㄴ Speaker Assembly - 7
54
Connect rear side of the frame using short back
bar.
ㄴ Speaker Assembly - 8
55
Tighten whole points using manual
hexagonal wrench.
ㄴ Speaker Assembly - 9
56
Connected frame on NLA-5 RACK
ㄴ Speaker Assembly - 10
57
Put NLA-15S under NLA-5 RACK.
ㄴ Speaker Assembly - 11
58
Tighten up and down holes in FRONT BAR
with bolts.
ㄴ Speaker Assembly - 12
59
Connect the middle with a bolt.
ㄴ Speaker Assembly - 13
60
Connect the lower part of short back bar with
bolts.
ㄴ Speaker Assembly - 14
61
Connect the up hole with a bolt.
ㄴ
Speaker Assembly - 15
62
Put one NLA-5 below, and tighten the up
and down holes of FRONT BAR with bolts.
ㄴ
Speaker Assembly - 16
63
Match middle hole in the bar and the speaker by
adjusting position of them.
ㄴ
Speaker Assembly - 17
64
Tighten the middle hole with bolts.
ㄴ
Speaker Assembly - 18
65
Connect the downside of the short back bar
with bolts.
ㄴ
Speaker Assembly - 19
66
Lift up the speaker with chain block, and
match up hole with speaker’s hole.
ㄴ
Speaker Assembly - 20
67
Connect the up hole with a bolt.
ㄴ
Speaker Assembly - 21
68
Completed 1 set of NLA-5
ㄴ
Speaker Assembly - 22
69
Put another NLA-5 below.
ㄴ
Speaker Assembly - 23
70
Align front part of NLA-5 using chain
block.
ㄴ
Speaker Assembly - 24
71
Connect the up and down hole in the FRO
NT BAR with bolts.
ㄴ
Speaker Assembly - 25
72
Match middle hole in the bar and the speaker by
adjusting position of them.
ㄴ
Speaker Assembly - 26
73
Tighten the middle hole with bolts.
ㄴ
Speaker Assembly - 27
74
Connect the downside of the long back
bar with bolts.
ㄴ
Speaker Assembly - 28
75
Rear part of NLA-5
5
0
10
Angles for each hole
ㄴ
Speaker Assembly - 29
76
You can see that this picture is set to 0
degree.
5
0
10
ㄴ
Speaker Assembly - 30
77
Choose your preferred angle
of hole using chain block.
The example in the photo is 0
degree.
ㄴ
Speaker Assembly - 31
78
Connect it with a bolt.
ㄴ
Speaker Assembly - 32
79
Completed 2 set of NLA-5
ㄴ
Speaker Assembly - 33
80
Fully completed figure after repeated
process.
Caution
81
ㄴ
Caution
82
1. You should insert spring washer and flat
washer for your bolts.
2. THREE holes in the front part of the speaker
must be connected with bolts.
(Connecting only 2 holes(up&down) might
cause a problem)
3. Position for shackle connecting to the frame
is up to user’s preference.
ㄴ
Caution
83
4. For tightening bolts, electric screw driver is
more convenient and safe than manual
hexagonal wrench.
5. When you use electric screw driver, it is
recommended to use slow motor speed. (Fast
motor speed easily makes a crooked bolt)
6. For your safety and convenience, you have to
tighten bolts with manual hexagonal wrench
after you use electric screw driver.