of 51
7/29/2019 NodeB Commissioning Guide(V200_01)
1/51
NodeB
V200
Commissioning Guide
Issue 01
Date 2008-04-30
Part Number
Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
7/29/2019 NodeB Commissioning Guide(V200_01)
2/51
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For any
assistance, please contact our local office or company headquarters.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: [email protected]
Copyright Huawei Technologies Co., Ltd. 2008. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written
consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are the property of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but the statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
mailto:[email protected]://www.huawei.com/7/29/2019 NodeB Commissioning Guide(V200_01)
3/51
Contents
About This Document.....................................................................................................................1
1 Procedure for Commissioning the NodeB............................................................................1-1
2 Upgrading the NodeB Software..............................................................................................2-1
2.1 Querying the Current Version of the NodeB .................................................................................................2-2
2.2 Downloading the BootROM Software Package of the NodeB.......................................................................2-2
2.3 Activating the BootROM Software of the NodeB..........................................................................................2-5
2.4 Downloading the Software of the NodeB.......................................................................................................2-7
2.5 Activating the Software of the NodeB..........................................................................................................2-11
3 Downloadingthe NodeB Data Configuration File.............................................................3-1
4 Handling Alarms During NodeB Commissioning .............................................................4-1
5 Checking the Running State of the NodeB...........................................................................5-1
5.1 Checking SNTP...............................................................................................................................................5-2
5.2 Checking the Status of a Cell..........................................................................................................................5-3
5.3 Measuring RTWP............................................................................................................................................5-3
5.4 Monitoring the Output Power of the NodeB...................................................................................................5-5
6 Initially Activating the NodeB License..................................................................................6-1
6.1 Uploading the RAN License to the M2000 Server.........................................................................................6-3
6.2 Allocating the NodeB License........................................................................................................................6-3
6.3 Activating the RAN License...........................................................................................................................6-4
6.4 Checking the RAN License Information.........................................................................................................6-5
7 Data Sheet for NodeB Commissioning..................................................................................7-1
Index.................................................................................................................................................i-1
NodeB
Commissioning Guide Contents
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
i
7/29/2019 NodeB Commissioning Guide(V200_01)
4/51
7/29/2019 NodeB Commissioning Guide(V200_01)
5/51
Figures
Figure 1-1 Flow chart of the commissioning.......................................................................................................1-2
Figure 2-1 Software Update dialog box...............................................................................................................2-3
Figure 2-2 Upgrade BOOTROM dialog box.......................................................................................................2-4
Figure 2-3 FTP Setting dialog box.......................................................................................................................2-4
Figure 2-4 Software Update dialog box...............................................................................................................2-6
Figure 2-5 Upgrade BOOTROM dialog box.......................................................................................................2-7
Figure 2-6 Software Update dialog box...............................................................................................................2-8
Figure 2-7 Upgrade Software dialog box.............................................................................................................2-9
Figure 2-8 FTP Setting dialog box.....................................................................................................................2-10
Figure 2-9 Software Update dialog box.............................................................................................................2-12
Figure 2-10 Upgrade Software dialog box.........................................................................................................2-13
Figure 3-1 DataConfig File Transfer dialog box..................................................................................................3-2
Figure 3-2 FTP Setting dialog box.......................................................................................................................3-2
Figure 5-1 RTWP Measurement dialog box........................................................................................................5-4Figure 5-2 Output Power Monitoring dialog box.................................................................................................5-6
NodeB
Commissioning Guide Figures
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
iii
7/29/2019 NodeB Commissioning Guide(V200_01)
6/51
7/29/2019 NodeB Commissioning Guide(V200_01)
7/51
Tables
Table 2-1 Elements in the FTP Setting dialog box...............................................................................................2-5
Table 2-2 Elements in the FTP Setting dialog box.............................................................................................2-10
Table 3-1 Elements in the FTP Setting dialog box...............................................................................................3-3
Table 7-1 Data Sheet for NodeB Commissioning................................................................................................7-1
NodeB
Commissioning Guide Tables
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
v
7/29/2019 NodeB Commissioning Guide(V200_01)
8/51
7/29/2019 NodeB Commissioning Guide(V200_01)
9/51
About This Document
Overview
The NodeB Commissioning Guide describes the commissioning and verification after the
installation of the NodeB. The commissioning ensures that the NodeB works properly asdesigned.
This document provides guidelines for NodeB commissioning, including introducing the
commissioning procedure, upgrading NodeB software and downloading the data configuration
file, handling NodeB alarms, checking the NodeB running status, and initially activating the
NodeB license.
Version
The following table lists the product versions related to this document.
Product Name Version
NodeB V200R010
Intended Audience
This document is intended for:
l Field engineers
l System engineers
Change History
Refer to Changes in the NodeB Commissioning Guide.
Organization
1 Procedure for Commissioning the NodeB
This describes the procedure for commissioning the NodeB. You can start commissioning the
NodeB if the prerequisites for commissioning are satisfied.
2 Upgrading the NodeB Software
NodeB
Commissioning Guide About This Document
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
1
http://-/?-http://-/?-7/29/2019 NodeB Commissioning Guide(V200_01)
10/51
The describes how to upgrade the NodeB software by downloading and activating BootROM
and software.
3 Downloading the NodeB Data Configuration File
This describes how to download the NodeB data configuration file from the FTP server to theNodeB. The NodeB data configuration file will take effect after the NodeB is reset.
4 Handling Alarms During NodeB Commissioning
This describes how to check active alarms on the NodeB and clear the alarms if any.
5 Checking the Running State of the NodeB
This describes how to check the running state of the NodeB to rectify faults that occur during
the operation, ensuring proper operation of the NodeB.
6 Initially Activating the NodeB License
This describes how to initially activate the NodeB license. When a new NodeB is configured,
the M2000 allocates the license resource to it. The task includes uploading the RAN license to
the M2000 server, distributing the NodeB license, activating the RAN license, and querying the
RAN license information.
7 Data Sheet for NodeB Commissioning
The data sheet for NodeB commissioning is used to record the process and results of the
commissioning.
Conventions
1. Symbol Conventions
The following symbols may be found in this document. They are defined as follows
Symbol Description
DANGER
Indicates a hazard with a high level of risk that, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazard with a medium or low level of risk which, if
not avoided, could result in minor or moderate injury.
CAUTION
Indicates a potentially hazardous situation that, if not avoided,
could cause equipment damage, data loss, and performance
degradation, or unexpected results.
TIP Indicates a tip that may help you solve a problem or save your
time.
NOTE Provides additional information to emphasize or supplement
important points of the main text.
2. General Conventions
About This Document
NodeB
Commissioning Guide
2 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
11/51
Convention Description
Times New Roman Normal paragraphs are in Times New Roman.
Boldface Names of files,directories,folders,and users are in boldface. Forexample,log in as userroot .
Italic Book titles are in italics.
Courier New Terminal display is in Courier New.
3. Command Conventions
Convention Description
Boldface The keywords of a command line are in boldface.
Italic Command arguments are in italic.
[ ] Items (keywords or arguments) in square brackets [ ] are optional.
{x | y | ...} Alternative items are grouped in braces and separated by vertical
bars.One is selected.
[ x | y | ... ] Optional alternative items are grouped in square brackets and
separated by vertical bars.One or none is selected.
{ x | y | ... } * Alternative items are grouped in braces and separated by vertical
bars.A minimum of one or a maximum of all can be selected.
[ x | y | ... ] * Alternative items are grouped in braces and separated by vertical
bars.A minimum of zero or a maximum of all can be selected.
4. GUI Conventions
Convention Description
Boldface Buttons,menus,parameters,tabs,window,and dialog titles are in
boldface. For example,clickOK.
> Multi-level menus are in boldfaceand separated by the ">" signs.For example,choose File > Create > Folder .
5. Keyboard Operation
Convention Description
Key Press the key.For example,press Enter and press Tab.
Key1+Key2 Press the keys concurrently.For example,pressing Ctrl+Alt+A
means the three keys should be pressed concurrently.
NodeB
Commissioning Guide About This Document
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
3
7/29/2019 NodeB Commissioning Guide(V200_01)
12/51
Convention Description
Key1,Key2 Press the keys in turn.For example,pressing Alt,A means the two
keys should be pressed in turn.
6. Mouse Operation
Action Description
Click Select and release the primary mouse button without moving the
pointer.
Double-click Press the primary mouse button twice continuously and quickly
without moving the pointer.
Drag Press and hold the primary mouse button and move the pointer
to a certain position.
About This Document
NodeB
Commissioning Guide
4 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
13/51
1 Procedure for Commissioning the NodeBThis describes the procedure for commissioning the NodeB. You can start commissioning the
NodeB if the prerequisites for commissioning are satisfied.
Prerequisite
l The hardware of the NodeB, such as the cabinet, cables, antenna system, and auxiliary
devices, passes the installation check and the NodeB is powered on.
l The negotiation data of the NodeB to be commissioned is configured on the RNC and
recorded.
The appropriate commissioning tool is selected based on transmission status between the
NodeB and the RNC.
l When transmission is available, use the M2000 to perform remote commissioning.
l When transmission is unavailable, use the LMT to perform local commissioning.
Flow chart of the commissioning
Figure 1-1 shows the flow chart of the commissioning of the NodeB.
NodeB
Commissioning Guide 1 Procedure for Commissioning the NodeB
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
1-1
7/29/2019 NodeB Commissioning Guide(V200_01)
14/51
Figure 1-1 Flow chart of the commissioning
Procedure
Step 1 Determine whether the software is required to be upgraded.
1 Procedure for Commissioning the NodeB
NodeB
Commissioning Guide
1-2 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
15/51
If Then
The software version is not upgraded and the
data configuration file is not downloaded,
Go to Step 2.
The NodeB software is upgraded by using aUSB memory key during installation,
Go to Step 3.
The software version is upgraded and the data
configuration file is downloaded,
Go to Step 4.
Step 2 Perform 2 Upgrading the NodeB Software.
Step 3 Perform 3 Downloading the NodeB Data Configuration File.
Step 4 Perform 4 Handling Alarms During NodeB Commissioning .
Step 5 Perform 5 Checking the Running State of the NodeB.
Step 6 Perform 6 Initially Activating the NodeB License.
Step 7 Notify the M2000 administrator that the commissioned NodeB can be managed by the M2000.
Step 8 Record the commissioning process and problems that occur during the commissioning in 7 DataSheet for NodeB Commissioning, and then export the commissioning report.
----End
NodeB
Commissioning Guide 1 Procedure for Commissioning the NodeB
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
1-3
7/29/2019 NodeB Commissioning Guide(V200_01)
16/51
7/29/2019 NodeB Commissioning Guide(V200_01)
17/51
2 Upgrading the NodeB SoftwareAbout This Chapter
The describes how to upgrade the NodeB software by downloading and activating BootROM
and software.
2.1 Querying the Current Version of the NodeB
This describes how to query the running NodeB software version before upgrading the NodeB
software.
2.2 Downloading the BootROM Software Package of the NodeB
This describes how to download the NodeB BootROM software package from the FTP server
to the temporary directory on the main processing board and then to the related boards.
2.3 Activating the BootROM Software of the NodeB
This describes how to activate the NodeB BootROM software. Activating the BootROM
software refers that the main processing board sends the BootROM update command to all the
boards that successfully download the BootROM software, and then updates each board
BootROM.
2.4 Downloading the Software of the NodeB
This describes how to download the NodeB software from the FTP server to the standby file
directory on the NodeB. The NodeB file directories are the active directory and the standby
directory. Active directory: stores the running NodeB software version. Standby directory: stores
the inactive NodeB software version. The NodeB software does not take effect immediately or
damage the running software after the download.
2.5 Activating the Software of the NodeB
This describes how to switch the standby directory to the active one, and then download the
NodeB software to each board and validate it. You can activate the NodeB software right after
the downloading or later on. After the activation, the NodeB is reset. Thus, all the services are
disrupted.
NodeB
Commissioning Guide 2 Upgrading the NodeB Software
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-1
7/29/2019 NodeB Commissioning Guide(V200_01)
18/51
2.1 Querying the Current Version of the NodeB
This describes how to query the running NodeB software version before upgrading the NodeB
software.
Prerequisite
l You have logged in to the NodeB LMT or the M2000.
Procedure
Run the LST SOFTWARE command to query the NodeB software version and BootROM
version.
----End
2.2 Downloading the BootROM Software Package of theNodeB
This describes how to download the NodeB BootROM software package from the FTP server
to the temporary directory on the main processing board and then to the related boards.
Prerequisite
l You have successfully logged in to the NodeB LMT or M2000.
l The NodeB version and BootROM version are checked and recorded.
Procedure
Step 1 Click the Maintenance tab in the navigation pane.
Step 2 Double-clickSoftware Management > Software Update. The Software Update dialog boxis displayed, as shown in Figure 2-1.
2 Upgrading the NodeB Software
NodeB
Commissioning Guide
2-2 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
19/51
Figure 2-1 Software Update dialog box
Step 3 Select Upgrade BOOTROM in the dialog box.
Step 4 ClickNext. The Upgrade BOOTROM dialog box is displayed, as shown in Figure 2-2.
NodeB
Commissioning Guide 2 Upgrading the NodeB Software
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-3
7/29/2019 NodeB Commissioning Guide(V200_01)
20/51
Figure 2-2 Upgrade BOOTROM dialog box
NOTE
l The system downloads the BootROM package and then activates it.
l You can choose one step each time and the system proceeds with the task you customize.
Step 5 ClickModify. The FTP Setting dialog box is displayed, as shown in Figure 2-3.
Figure 2-3 FTP Setting dialog box
2 Upgrading the NodeB Software
NodeB
Commissioning Guide
2-4 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
21/51
Table 2-1 describes the elements in the FTP Setting dialog box.
Table 2-1 Elements in the FTP Setting dialog box
Element Description
Use Built-in FTP Server This enables you to decide whether to use a built-in or a
specified FTP server. The built-in FTP server is started
by default.
Use
Specified
FTP Server
IP Address The FTP server can either be started from the local
computer installed with the LMT application or from
another computer. Here it refers to the IP address of the
FTP server.
User Name This enables you to specify the user name for logging in
to the FTP server.
Password This enables you to specify the password for logging in
to the FTP server.
Step 6 Set the FTP server.
Step 7 ClickOK. The FTP Setting dialog box is closed and the Upgrade BOOTROM dialog box isdisplayed.
Step 8 Select Download BOOTROM Package and then specify a path to download the BootROMpackage.
Step 9 ClickNext. A dialog box is displayed for your confirmation.
Step 10 ClickYes. The status and progress of the procedure are displayed in Interface of Indicatingthe Status and the Progress. You can check the procedure by viewing this dialog box.
----End
2.3 Activating the BootROM Software of the NodeB
This describes how to activate the NodeB BootROM software. Activating the BootROM
software refers that the main processing board sends the BootROM update command to all the
boards that successfully download the BootROM software, and then updates each board
BootROM.
Prerequisite
You have successfully logged in to the NodeB LMT or M2000.
Context
l Before the activation, the system checks the BootROM versions of the boards. It activates
the board BootROM only when there is a new BootROM version. If there is no new
BootROM version, the system does not activate the board BootROM.
l
If the activation of a board fails, locate the problem and then activate the software of thatboard again. For details, refer to Activating the BootROM Software of a Board.
NodeB
Commissioning Guide 2 Upgrading the NodeB Software
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-5
http://-/?-http://-/?-http://-/?-http://-/?-7/29/2019 NodeB Commissioning Guide(V200_01)
22/51
l Because the BootROM software does not affect the NodeB services, you need not reset the
NodeB to make the BootROM effective. The NodeB starts with the upgraded BootROM
during next reset.
l After the BootROM is activated, the NodeB is not reset.
Procedure
Step 1 Click the Maintenance tab in the navigation pane.
Step 2 Double-clickSoftware Management > Software Update. The Software Update dialog boxis displayed, as shown in Figure 2-4.
Figure 2-4 Software Update dialog box
Step 3 Select Upgrade BOOTROM in the dialog box.
Step 4 ClickNext. The Upgrade BOOTROM dialog box is displayed, as shown in Figure 2-5.
2 Upgrading the NodeB Software
NodeB
Commissioning Guide
2-6 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
23/51
Figure 2-5 Upgrade BOOTROM dialog box
NOTE
l The system downloads the BootROM package and then activates it.
l You can choose one step each time and the system proceeds with the task you customize.
Step 5 Select Activate BOOTROM.
Step 6 ClickNext. A dialog box is displayed for your confirmation.
Step 7 ClickYes. The status and progress of the procedure are displayed in Interface of Indicatingthe Status and the Progress. You can check the procedure by viewing this dialog box.
----End
2.4 Downloading the Software of the NodeB
This describes how to download the NodeB software from the FTP server to the standby file
directory on the NodeB. The NodeB file directories are the active directory and the standby
directory. Active directory: stores the running NodeB software version. Standby directory: stores
the inactive NodeB software version. The NodeB software does not take effect immediately or
damage the running software after the download.
NodeB
Commissioning Guide 2 Upgrading the NodeB Software
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-7
http://-/?-http://-/?-7/29/2019 NodeB Commissioning Guide(V200_01)
24/51
Prerequisite
l You have successfully logged in to the NodeB LMT or M2000.
ProcedureStep 1 Click the Maintenance tab in the navigation pane.
Step 2 Double-clickSoftware Management > Software Update. The Software Update dialog boxis displayed, as shown in Figure 2-6.
Figure 2-6 Software Update dialog box
Step 3 Select Upgrade Software in the dialog box.
Step 4 ClickNext. The Upgrade Software dialog box is displayed, as shown in Figure 2-7.
2 Upgrading the NodeB Software
NodeB
Commissioning Guide
2-8 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
25/51
Figure 2-7 Upgrade Software dialog box
NOTE
l The steps explained in the preceding table are performed in order: Backup Data Configuration
File, Download Software Package, and then Activate Software.
l You can choose one or multiple steps each time and the system proceeds with the task you customize.
Step 5 ClickModify. The FTP Setting dialog box is displayed, as shown in Figure 2-8.
NodeB
Commissioning Guide 2 Upgrading the NodeB Software
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-9
7/29/2019 NodeB Commissioning Guide(V200_01)
26/51
Figure 2-8 FTP Setting dialog box
Table 2-2 describes the elements in the FTP Setting dialog box.
Table 2-2 Elements in the FTP Setting dialog box
Element Description
Use Built-in FTP Server This enables you to decide whether to use a built-in or a
specified FTP server. The built-in FTP server is started
by default.
Use
Specified
FTP Server
IP Address The FTP server can either be started from the local
computer installed with the LMT application or from
another computer. Here it refers to the IP address of theFTP server.
User Name This enables you to specify the user name for logging in
to the FTP server.
Password This enables you to specify the password for logging in
to the FTP server.
Step 6 Set the FTP server.
Step 7 ClickOK. The FTP Setting dialog box is closed and the Upgrade Software dialog box isdisplayed.
Step 8 Select Backup Data Configuration File to specify a directory for backing up the file. SelectDownload Software Package to specify a directory for downloading the software package.
NOTE
Backup Data Configuration File is optional.
Step 9 ClickNext. A dialog box is displayed for your confirmation.
Step 10 ClickYes. The status and progress of the procedure are displayed in Interface of Indicatingthe Status and the Progress. You can check the procedure by viewing this dialog box.
----End
2 Upgrading the NodeB Software
NodeB
Commissioning Guide
2-10 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
http://-/?-http://-/?-7/29/2019 NodeB Commissioning Guide(V200_01)
27/51
2.5 Activating the Software of the NodeB
This describes how to switch the standby directory to the active one, and then download the
NodeB software to each board and validate it. You can activate the NodeB software right after
the downloading or later on. After the activation, the NodeB is reset. Thus, all the services are
disrupted.
Prerequisite
You have successfully logged in to the NodeB LMT or M2000.
Context
The NodeB software does not take effect immediately or damage the running software after the
download. You can activate the NodeB software to make the new software effective.
Procedure
Step 1 Click the Maintenance tab in the navigation pane.
Step 2 Double-clickSoftware Management > Software Update. The Software Update dialog boxis displayed, as shown in Figure 2-9.
NodeB
Commissioning Guide 2 Upgrading the NodeB Software
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-11
7/29/2019 NodeB Commissioning Guide(V200_01)
28/51
Figure 2-9 Software Update dialog box
Step 3 Select Upgrade Software in the dialog box.
Step 4 ClickNext. The Upgrade Software dialog box is displayed, as shown in Figure 2-10.
2 Upgrading the NodeB Software
NodeB
Commissioning Guide
2-12 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
29/51
Figure 2-10 Upgrade Software dialog box
NOTE
l The steps explained in the preceding table are performed in order: Backup Data Configuration
File, Download Software Package, and then Activate Software.
l You can choose one or multiple steps each time and the system proceeds with the task you customize.
Step 5 Select Activate Software and select the software version to be upgraded in the Version box.
NOTE
The Version box is displayed only when Download Software is not selected.
Step 6 ClickNext. A dialog box is displayed for your confirmation.
Step 7 ClickYes. The status and progress of the procedure are displayed in Interface of Indicatingthe Status and the Progress. You can check the procedure by viewing this dialog box.
NodeB
Commissioning Guide 2 Upgrading the NodeB Software
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-13
http://-/?-http://-/?-7/29/2019 NodeB Commissioning Guide(V200_01)
30/51
NOTE
l If the activation of a board fails, locate the problem and then activate the software of that board again.
For details, refer to Activating the Software of a Board.
l The is reset and the new software version is started when software is activated.
l Reactivate the software version in the standby file directory or reinstall the software upon activation
failure.
----End
2 Upgrading the NodeB Software
NodeB
Commissioning Guide
2-14 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
http://-/?-7/29/2019 NodeB Commissioning Guide(V200_01)
31/51
3 Downloading the NodeB DataConfiguration File
This describes how to download the NodeB data configuration file from the FTP server to the
NodeB. The NodeB data configuration file will take effect after the NodeB is reset.
Prerequisite
You have successfully logged in to the NodeB LMT or M2000.
Procedure
l In GUI mode
1. Click the Maintenance tab in the navigation pane.
2. Double-clickSoftware Management > Data Config File Transfer. The Data
Configuration File Transfer dialog box is displayed, as shown in Figure 3-1.
NodeB
Commissioning Guide 3 Downloading the NodeB Data Configuration File
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
3-1
7/29/2019 NodeB Commissioning Guide(V200_01)
32/51
Figure 3-1 DataConfig File Transfer dialog box
3. Select Download (FTP Server to ) in the Transfer Type area.
4. Click Modify in the dialog box. The FTP Setting dialog box is displayed, as shown
in Figure 3-2.
Figure 3-2 FTP Setting dialog box
Table 3-1 describes the elements in the FTP Setting dialog box.
3 Downloading the NodeB Data Configuration File
NodeB
Commissioning Guide
3-2 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
33/51
Table 3-1 Elements in the FTP Setting dialog box
Element Description
Use Built-in FTP Server This enables you to decide whether to use a built-
in or a specified FTP server. The built-in FTPserver is started by default.
Use
Specified
FTP Server
IP Address The FTP server can either be started from the local
computer installed with the LMT application or
from another computer. Here it refers to the IP
address of the FTP server.
User Name This enables you to specify the user name for
logging in to the FTP server.
Password This enables you to specify the password for
logging in to the FTP server.
5. Set the FTP server.
6. Click OK. The FTP Setting dialog box is closed and the DataConfig File
Transfer dialog box is displayed.
7. Set the other parameters in the dialog box.
8. Click Start. The system starts downloading the data configuration file.
l In MML mode
To download the data configuration file, run DLD CFGFILE.
----End
NodeB
Commissioning Guide 3 Downloading the NodeB Data Configuration File
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
3-3
7/29/2019 NodeB Commissioning Guide(V200_01)
34/51
7/29/2019 NodeB Commissioning Guide(V200_01)
35/51
4 Handling Alarms During NodeBCommissioning
This describes how to check active alarms on the NodeB and clear the alarms if any.
Prerequisite
You have logged in to the NodeB LMT or the M2000.
Procedure
Step 1 Run the LST ALMAF command to query the current active alarms.
Step 2 Handle the NodeB alarms.
If Then
An active NodeB alarm exists, Clear it according to the LMT alarm online help.
An active NodeB alarm cannot be
cleared,
Record it in the 7 Data Sheet for NodeB
Commissioning.
----End
NodeB
Commissioning Guide 4 Handling Alarms During NodeB Commissioning
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
4-1
7/29/2019 NodeB Commissioning Guide(V200_01)
36/51
7/29/2019 NodeB Commissioning Guide(V200_01)
37/51
5 Checking the Running State of the NodeBAbout This Chapter
This describes how to check the running state of the NodeB to rectify faults that occur during
the operation, ensuring proper operation of the NodeB.
5.1 Checking SNTP
This describes how to commission the Simple Network Time Protocol (SNTP) to synchronize
the time between NEs. The task facilitates the centralized maintenance and management.
5.2 Checking the Status of a Cell
This describes how to check the status of a local cell or a logical cell. The task helps you to learn
the running state of the active cell and perform OM on the cell.
5.3 Measuring RTWP
The Received Total Wideband Power (RTWP) is the received wideband power in an uplink
channel band measured at the UMTS Terrestrial Radio Network Access (UTRAN) access point.
This topic describes how to measure the RTWP. You can calibrate the gain of uplink RF channels
through RTWP measurement. The NodeB RTWP test has no negative effect on the services.
NodeB
Commissioning Guide 5 Checking the Running State of the NodeB
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
5-1
7/29/2019 NodeB Commissioning Guide(V200_01)
38/51
5.1 Checking SNTP
This describes how to commission the Simple Network Time Protocol (SNTP) to synchronize
the time between NEs. The task facilitates the centralized maintenance and management.
Prerequisite
You have successfully logged in to the NodeB LMT or M2000.
Context
Application of the SNTP helps to synchronize the time (year/month/date/hour/minute/second)
between multiple SNTP clients in real time by using a unique SNTP server.
ProcedureStep 1 Start the SNTP server. An SNTP server can be at the RNC or at the M2000 server, which is
determined by the actual condition.
l At the RNC: Enable the SNTP service on the SecurityManager of the BAM.
l At the M2000 server: The Sun operating system has the self-contained SNTP service. For
details, refer to theM2000 Administration Guide.
Step 2 Run the SET SNTPCLTPARA command to set the parameters of the SNTP client.
Parameter ID Parameter Name Description
SW Switch of Time Sync Indicates whether synchronization is
required.
Value range: ON (synchronization
required), OFF (synchronization not
required)
Default value: none.
IP SNTP Server IP Address Value range: 0.0.0.1 to 255.255.255.254
Default value: none.
SP Synchronization period
(minute)
Value range: 1 to 525600
Unit: minute
Default value: none.
Step 3 Run the LST SNTPCLTPARA command to check the parameters of the SNTP client.
Step 4 Run the LST SNTPCLTLATESTSUCCDATE command to query the time of latest successfulsynchronization of the SNTP client to the SNTP server, and whether the synchronization is
successful.
5 Checking the Running State of the NodeB
NodeB
Commissioning Guide
5-2 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
39/51
If.. Then..
The synchronization is successful, End this task.
The synchronization is failed, Check the following items:
l Whether the SNTP server is started
l Whether the IP address of the NodeB is correct
After the faults are rectified, go to Step 2 to reset the
parameters.
----End
5.2 Checking the Status of a CellThis describes how to check the status of a local cell or a logical cell. The task helps you to learn
the running state of the active cell and perform OM on the cell.
Prerequisite
You have successfully logged in to the NodeB LMT or M2000.
Procedure
Run the DSP LOCELL command to check the statuses of all local and logical cells of the
NodeB.
If Then
The information prompting faults is
displayed,
Rectify the faults according to the
information.
No information prompting faults is
displayed,
End the task.
----End
5.3 Measuring RTWP
The Received Total Wideband Power (RTWP) is the received wideband power in an uplink
channel band measured at the UMTS Terrestrial Radio Network Access (UTRAN) access point.
This topic describes how to measure the RTWP. You can calibrate the gain of uplink RF channels
through RTWP measurement. The NodeB RTWP test has no negative effect on the services.
Prerequisite
You have successfully logged in to the NodeB LMT or M2000.
NodeB
Commissioning Guide 5 Checking the Running State of the NodeB
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
5-3
7/29/2019 NodeB Commissioning Guide(V200_01)
40/51
Context
Analyses of the RTWP measurement are as follows:
l If the NodeB is not connected to the antenna and feeder system or a matched load, the
RTWP is about 108 dBm. If the NodeB is connected to the antenna and feeder system(with TMA switched on) or a matched load, the RTWP is about 105 dBm.
l If the services are normal and the uplink load reaches 75%, the RTWP is 6 dB higher than
the RTWP when the NodeB does not carry any service.
NOTE
l When the reported RTWP is valid, the curve is normal. The vertical axis corresponds to the reported
RTWP with the unit of 0.1 dBm.
l When the reported RTWP is invalid, abnormal RTWP curves are displayed. The RTWP for the main
antenna forms a horizontal line at 112 dBm on the vertical axis. The RTWP for the diversity antenna
forms a horizontal line at 111.5 dBm on the vertical axis. The error may lie in the absent WRFU
\MRRU\RHUB\PRRU, a broken link, or a faulty channel. In this case, clear the fault first.
Procedure
Step 1 In the navigation pane of the Local Maintenance Terminal window, click the Maintenancetab.
Step 2 Double-clickRealtime Specific Monitoring > RTWP Measurement . The RTWPMeasurement dialog box is displayed, as shown in Figure 5-1.
Figure 5-1 RTWP Measurement dialog box
Step 3 Set the parameters in the dialog box.
Step 4 ClickOK. A monitor window is displayed, showing the current monitoring task in graphs.
Step 5 Stop the test in one of the following ways:
If... Then...
You close the monitoring window, All the displayed monitoring tasks are
stopped.
5 Checking the Running State of the NodeB
NodeB
Commissioning Guide
5-4 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
41/51
If... Then...
Right-click the task in the task list area and
then choose Delete Task from the shortcut
menu,
The task and its chart are deleted.
----End
5.4 Monitoring the Output Power of the NodeB
This describes how to monitor the output power of the NodeB. The output power test measures
the output power of the NodeB, including the typical output power and output power of each
carrier.
PrerequisiteYou have successfully logged in to the NodeB LMT or M2000.
Context
If the test is started, the system periodically reports the typical output power and power of each
carrier according to the set time interval.
The output power the NodeB is associated with the configuration and specified services. If the
pilot power and typical output power are configured, when the NodeB does not carry services,
the WRFU output power is close to the pilot power and the RRU/pRRU output power is close
to the pilot power plus 3 dB. If the output power is lower than the pilot power by a large amount,the NodeB output power must be abnormal.
l WRFU and RRU: The pilot power can be 33 dBm and the typical power can be 43 dBm.
l pRRU: Because the output power is relative small, the pilot power can be 20 dBm and the
typical power can be 27 dBm.
Procedure
Step 1 In the navigation pane of the Local Maintenance Terminal window, click the Maintenancetab.
Step 2 Double-clickRealtime Specific Monitoring > Output Power Monitoring . The OutputPower Monitoring dialog box is displayed, as shown in Figure 5-2.
NodeB
Commissioning Guide 5 Checking the Running State of the NodeB
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
5-5
7/29/2019 NodeB Commissioning Guide(V200_01)
42/51
Figure 5-2 Output Power Monitoring dialog box
Step 3 Set the parameters in the dialog box.
Step 4 ClickOK. A monitor window is displayed, showing the current monitoring task in graphs.
Step 5 Stop the test in one of the following ways:
If... Then...
You close the monitoring window, All the displayed monitoring tasks are
stopped.
Right-click the task in the task list area and
then choose Delete Task from the shortcut
menu,
The task and its chart are deleted.
----End
5 Checking the Running State of the NodeB
NodeB
Commissioning Guide
5-6 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
43/51
6 Initially Activating the NodeB LicenseAbout This Chapter
This describes how to initially activate the NodeB license. When a newNodeB is configured,
the M2000 allocates the license resource to it. The task includes uploading the RAN license to
the M2000 server, distributing the NodeB license, activating the RAN license, and querying the
RAN license information.
Prerequisite
l The M2000 server is operational.
l A valid NodeB license file is obtained.
l The ESN is successfully obtained from the RAN.
Context
A license is an authorization agreement between the supplier and the operator in terms of the
functions, application scope, and service life of products. Physically, a license are/is a license
certificate and/or a license file. Operators can purchase a license which specifies the network
functions and capacity applicable to a specific phase. In this way, the investment of the operators
can be fully protected.
1. 6.1 Uploading the RAN License to the M2000 Server
This describes how to upload the RAN license file to the M2000 server through the M2000
client. The task enables the M2000 service of RAN license management to manage the
license file.
2. 6.2 Allocating the NodeB License
This describes how the M2000 allocates the NodeB license files uploaded to the M2000
server to operators.
3. 6.3 Activating the RAN License
This describes how to activate the RAN license. When an RNC license is activated, the
allocation of the license among operators is complete. When a NodeB license is activated,
the allocation of the license among NodeBs is complete.
4. 6.4 Checking the RAN License Information
NodeB
Commissioning Guide 6 Initially Activating the NodeB License
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
6-1
7/29/2019 NodeB Commissioning Guide(V200_01)
44/51
This describes how to check the license file information about the RNC and NodeB on the
M2000 server.
6 Initially Activating the NodeB License
NodeB
Commissioning Guide
6-2 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
45/51
6.1 Uploading the RAN License to the M2000 Server
This describes how to upload the RAN license file to the M2000 server through the M2000
client. The task enables the M2000 service of RAN license management to manage the license
file.
Prerequisite
l You have logged in to the M2000 client.
l The M2000 server is operational.
l The license to be uploaded is valid.
Context
l Each RAN system can upload one RNC license and multiple NodeB licenses to the M2000.
However, only one NodeB license can be activated at a time point.
l When the RAN system is shared by multiple operators, due to the varied information of
operators, the license is valid if the equipment ID in the license file is consistent with the
ESN of the primary operator's RNC.
Procedure
Step 1 Choose Software > License Management . The License Browser window is displayed.
Step 2 From the file navigation tree on the left part of the License Browser window, select an RNCnode.
Step 3 Right-click and choose Upload > From Client. The Select Uploading File-----1/1 dialog boxis displayed.
Step 4 ClickAdd. The Select dialog box is displayed.
Step 5 Select one or multiple license files to be uploaded and then clickSelect.
TIP
Hold ofShift orCtrl enables you to select multiple files.
Step 6 In the Select Uploading File-----1/1 dialog box, clickFinish. The upload progress is displayed
on the FTP Tasktab page at the lower part of the License Browser window. When the progressbar reaches 100%, you can infer that the license file is uploaded.
NOTE
If you need to stop or delete the task when the license file is being uploaded, you can select the file, right-
click and then choose Stop orDelete from the shortcut menu.
----End
6.2 Allocating the NodeB License
This describes how the M2000 allocates the NodeB license files uploaded to the M2000 serverto operators.
NodeB
Commissioning Guide 6 Initially Activating the NodeB License
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
6-3
7/29/2019 NodeB Commissioning Guide(V200_01)
46/51
Prerequisite
l You have logged in to the M2000 client.
l The M2000 server is operational.
l The ESN is successfully obtained from the RAN.
l The valid license file is uploaded to the M2000 server.
l The RAN system is shared by multiple operators.
Procedure
Step 1 Choose Software > License Management . The License Browser window is displayed.
Step 2 From the file navigation tree on the left part of the License Browser window, select an RNCnode whose license file is already uploaded to the M2000 server. The detailed license list on the
right part of the window displays all the licenses of the RNC node.
Step 3 Select a license, right-click it, and choose License Distributed to Operator from the shortcutmenu. The License Distributed to Operator window is displayed.
Step 4 In this window, assign the values of licenses to each operator.
NOTE
l The number of local cells set by the user must be equal to or more than the number of actual cells.
Otherwise, the allocation of NodeB license fails.
l You can run a MML command to query the parameter information of the NodeB, such as the actual
number of cells.
l When the license allocation information is modified on the NodeB, you need to allocate the license
information to all the NEs under the RNC node so that the modification takes effect.
Step 5 In the NE allocation information box, click an operator tab. All the licenses allocated to theoperator is displayed in the box.
Step 6 Double-click a piece of NE license allocation information or right-click the information and thenchoose Modify from the shortcut menu. The Modify dialog box is displayed.
Step 7 Modify the license allocation information of the NodeB. The license is delivered to the NE byoperators.
----End
6.3 Activating the RAN License
This describes how to activate the RAN license. When an RNC license is activated, the allocation
of the license among operators is complete. When a NodeB license is activated, the allocation
of the license among NodeBs is complete.
Prerequisite
l You have logged in to the M2000 client.
l The M2000 server is operational.
l
The valid RNC license and NodeB license are uploaded to the M2000 server. The allocationof the NodeB license among NodeBs is complete.
6 Initially Activating the NodeB License
NodeB
Commissioning Guide
6-4 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
47/51
Context
On the M2000 server, a RAN system can have multiple NodeB license files and one RNC license
file. Among the NodeB license files, only one of them can be activated at a time point.
Procedure
Step 1 Choose Software > License Management . The License Browser window is displayed.
Step 2 From the file navigation tree on the left part of the License Browser window, select an RNCnode. The detailed license list on the right part of the window displays all the licenses of the
RNC node.
Step 3 Select a license whose Activated parameter is False. Right-click and choose Distribute Allfrom the shortcut menu.
NOTE
l If the set parameter value is beyond the allowed range when you allocate the licenses to the operators,
a Message dialog box is displayed, informing you that the parameter value exceeds its thresholds. Click
OKand tune the parameter value.
l If the parameter value of a NodeB owned by an operator is not recommended, a Confirmation dialog
box is displayed. ClickYes to continue the license delivery or clickNo to cancel the license delivery.
----End
6.4 Checking the RAN License Information
This describes how to check the license file information about the RNC and NodeB on the M2000
server.
Prerequisite
l You have logged in to the M2000 client.
l The M2000 server is operational.
l The RAN license is uploaded to the server.
Context
You can manually modify the NodeB license allocation information.
Procedure
Step 1 Choose Software > License Management . The License Browser is displayed.
Step 2 From the file navigation tree on the left part, select an RNC node.
l The two tables in the upper right part of the window show the operators and licenses related
to the RAN.
The information about the operator consists ofOperator, ESN, and Primary
Operator.
The information about the license consists ofLicenseSN, Activated, CreateDate,
EndDate, and Control.
Step 3 Select a license. The detailed allocation information is displayed on the list below.
NodeB
Commissioning Guide 6 Initially Activating the NodeB License
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
6-5
7/29/2019 NodeB Commissioning Guide(V200_01)
48/51
NOTE
On the license list, double-click a license. In the displayed Detail dialog box, you can check the detailed
information about the license.
----End
6 Initially Activating the NodeB License
NodeB
Commissioning Guide
6-6 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
49/51
7Data Sheet for NodeB CommissioningThe data sheet for NodeB commissioning is used to record the process and results of the
commissioning.
Table 7-1 Data Sheet for NodeB Commissioning
Site Name
NodeB Model
Date & Time
Commissioning
Engineers
Commissioning
Result
Successful Failed
Item Conclusion Handling
Exceptional
Cases
Commissioning
preparation
Faults in NodeB hardware
installation are rectified.
Transmission links between the
NodeB and the RNC are ready.
Configuration data of the NodeB
is added to the RNC.
The NodeB data configuration file
is obtained.
The local IP address in the
NodeB data configuration file is
set.
NodeB
Commissioning Guide 7 Data Sheet for NodeB Commissioning
Issue 01 (2008-04-30) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
7-1
7/29/2019 NodeB Commissioning Guide(V200_01)
50/51
Item Conclusion Handling
Exceptional
Cases
Remote
commissioning
The NodeB software is upgraded.
The data configuration file of the
NodeB is downloaded.
The alarms during NodeB
commissioning are cleared.
The running state of the NodeB is
checked.
The NodeB license is initially
activated.
The M2000 administrator isnotified.
Open problems Impact
Open problems
during
commissioning
7 Data Sheet for NodeB Commissioning
NodeB
Commissioning Guide
7-2 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 01 (2008-04-30)
7/29/2019 NodeB Commissioning Guide(V200_01)
51/51
Index
A
activatingBootROM software, 2-5
NodeB software, 2-11RAN license, 6-4allocating
license, 6-3
C
checkingRAN license information, 6-5SNTP, 5-2status of cell, 5-3
D
downloadingBootROM software package, 2-2data configuration file, 3-1NodeB software, 2-7
H
handlingalarms during NodeB commissioning, 4-1
M
measuringRTWP, 5-3monitoring
output power, 5-5
P
procedurecommissioning, 1-1
Q
U
upgrading
NodeB software, 2-1uploadingRAN license to M2000 server, 6-3
NodeB
Commissioning Guide Index