Norsk Staal 2009 Engels k 141209

8/12/2019 Norsk Staal 2009 Engels k 141209

1/54

Norsk Stl is a leading supplier of steel and metals in Norway. With this catalogue, we wish to

give you an english version of our product catalogue.

Norsk Stl provides services; shotblasting and priming, cutting, machine cutting, ame and plas-

ma cutting.You can read more about these services under Information / Other services, or look for

Pre-treatment under www.norskstaal.no/export.

Norsk Stl wishes to be your partner in Norway, relating to delivery of steel and metals. Our ex-

port department are at your service. Please do not hesitate to contact us; [email protected]

or by phone 47 66 84 28 00.

On www.norskstaal.no you can read more about Norsk Stl and our export department. Look for

Export in the menu.

This catalogue is an extract of products we have in stock.

You will nd our full assortment of products in our product catalouge on www.norskstaal.no(in Norwegian).

December 2009

Foto: Harald Valderhaug


2/54

LIST OF CONTENT

Steel plates - Hot Rolled

page 3-12

1

2

3

4

5

6

7

8

Profiles - Hot RolledRounds, half rounds, flats, wide flats, bulb flats, angles, squares, tees

and L-profiles . page13-21,31

Beams and channels - Hot Rolled + Cold formed channels

UNP, UPE, IPE, HEA, HEB page 22-26

Cold formed channels page 31

Structural Hollow SectionsCold- and hot formed hollow sections page 27-30

Steel Sheets + Expanded Metals and gratingsHot dipped galvanized and elctrolytic sheets page 32

Expanded Metals and gratings page 33-34

Aluminium page 35-38

Tables page 39-48

Information / Other services page 49

STEELSHEETS

TABLES

ALUMINIUM

INFORMATION/

OTHERSERVICES


3/54www.norskstaal.no2

CONTENT

STEEL PLATES - HOT ROLLED

Steel plates S235JR/Domex 240YP 3

Steel plates NVA 3

Steel plates for pressure purposes P 265GH 5

Steel plates for pressure purposes P 355NL2 5

Steel plates S355J2 + N 7

Steel plates NVE 36 8

Steel plates S355G10 + N/M 8

Steel plates S420G2 + M/Q 10

Steel plates Domex S355MCD/E 8

Steel plates Domex S355MCD/E/B 8

Steel plates Domex S500MCD - 9

Steel plates Domex S650MCD 9

Steel plates Domex S700MCD 9

Steel plates Domex 355W - Cor-Ten 9

Steel plates Weldox 700E/S690QL 10

Steel plates Abrasion resistant Hardox 450 11Steel plates Abrasion resistant Hardox 500 11

Steel checker plates S235JR 12

Steel tear plates S235JR 12

Steel tear plates NVA 12

STEEL PROFILES - HOT ROLLED

Steel rounds S235JR 13

Steel rounds NVA 13

Steel rounds/shafts S355J2+N 13

Steel rounds S355J0 14

Steel rounds/shafts 34CrNiMo6 14

Steel half rounds NVA 14Steel squares S235JR 14

Steel flats S235JR 15

Steel flats NVA 16

Steel flats S355J2 17

Steel flats rails S355J0 17

Steel crane rails 17

Steel wide flats NVA 17

Steel wide flats S355J2 17

L-profile NVD 36 18

Steel bulb flats (HP) NVA 18

Steel bulb flats (HP) NVD 36 18

Steel angles S235JR 19

Steel angles NVA 20

Steel angles S355J2 21

Steel tees S235JR 21

STEEL BEAMS AND CHANNELS - HOT ROLLED

Steel channels UNP S235JR 22

Steel channels UNP S355J2 22

Steel channels UNP S355G11 + N/M 23

Steel channels UPE S355N 23

Steel sections IPE S355J2 24

Steel sections IPE S355G11 + N/M 24

Steel beams HEA S355J2 25

Steel beams HEA S355G11 + N/M 25Steel beams HEB S355J2 26

Steel beams HEB S355G11 + N/M 26

STEEL, STRUCTURAL HOLLOW SECTIONS

Welded circular Hybox S355J2H 27

Cold formed Hybox S355J2H 27-28

Hot formed Celsius S355NH 29-30

CHANNELS AND ANGLES, COLD-FORMED

Centerless rounds/shafts SS2142 30

Channels S235JR 31

Angles S235JR 31

STEEL SHEETS

Cold reduced DC01AM 31

Hot dipped galvanized 32

Electrolytic galvanized 32

Aluzink steel plates 32

Expamet Expanded Metal 33Gratings for offshore 34

ALUMINIUM

Aluminium sheets 35

Aluminium tread plates 36

Aluminium ship-plates 36

Aluminium round bars/shafts 36

Aluminium flats 37

Aluminium angles 37-38

Aluminium steel explosice welded transistion joints 38

TABLES

European Standards (EN) 39

Compares new European standards and

earlier national standards 40

Information Pre-treatment services 49

Product Page Product Page


4/54

STEEL

www.norskstaal.no 3

Steel plates S235JR/DOMEX 240YP,Lazerplates

Acc. to EN 10 025-2

Unique properties regarding Cold forming,tight bend radius and suitable for lazer cutting

Tolerances and flatness acc. to EN 10 051Inspection certificate acc. to EN 10 204-3.1

Quality marked along one side

ARTICLE GROUP 135

Article no. Dimension Kg/plate

135008 3,00 X 1000 X 2000 MM 48.00135015 3,00 X 1250 X 2500 MM 75.00135020 3,00 X 1250 X 3600 MM 108.00135021 3,00 X 1500 X 3000 MM 108.00

135022 3,00 X 1500 X 3600 MM 130.00135025 3,00 X 1500 X 5000 MM 180.00

135036 4,00 X 1000 X 2000 MM 64.00135043 4,00 X 1250 X 2500 MM 100.00135052 4,00 X 1500 X 3000 MM 144.00


135120 6,00 X 1000 X 2000 MM 96.00135127 6,00 X 1250 X 2500 MM 150.00135140 6,00 X 1500 X 3000 MM 216.00

135185 8,00 X 1000 X 2000 MM 128.00135190 8,00 X 1250 X 2500 MM 200.00135200 8,00 X 1500 X 3000 MM 288.00

135220 10,00 X 1000 X 2000 MM 160.00135225 10,00 X 1250 X 2500 MM 250.00135300 10,00 X 1500 X 3000 MM 360.00

135315 12,00 X 1000 X 2000 MM 192.00135320 12,00 X 1250 X 2500 MM 300.00135325 12,00 X 1500 X 3000 MM 432.00

135328 15,00 X 1000 X 2000 MM 240.00135330 15,00 X 1250 X 2500 MM 375.00135340 15,00 X 1500 X 3000 MM 540.00

Steel plates S235JR/DOMEX 240YP,Lazerplates

Acct. to EN 10 025-2.

Pickled and lightly oiledUniqe properties regarding Cold forming,

tight bend and suitable for lazer cuttingTolerances and flatness acc. to EN 10 051

Inspections certificate acc. to EN 10 204-3.1


Delivered as single sheets or in approx. 2000 kgs

envelopes.

ARTICLE GROUP 134


134020 2,0 X 1000 X 2000 MM 32.00

134025 2,0 X 1250 X 2500 MM 50.00

134028 2,5 X 1000 X 2000 MM 40.00

134031 3,0 X 1000 X 2000 MM 48.00134035 3,0 X 1250 X 2500 MM 75.00134038 3,0 X 1500 X 3000 MM 108.00

134041 4,0 X 1000 X 2000 MM 64.00134045 4,0 X 1250 X 2500 MM 100.00134048 4,0 X 1500 X 3000 MM 144.00


134061 6,0 X 1000 X 2000 MM 96.00134065 6,0 X 1250 X 2500 MM 150.00134068 6,0 X 1500 X 3000 MM 216.00

134075 8,0 X 1250 X 2500 MM 200.00134078 8,0 X 1500 X 3000 MM 288.00

134085 10,0 X 1250 X 2500 MM 250.00134088 10,0 X 1500 X 3000 MM 360.00134098 12,0 X 1500 X 3000 MM 432.00

Steel plates NVAThickness tolerances acc. to DNV rules

Remaining tolerances acc. to EN 10 029 Class B

Inspection certificate acc. to EN 10 024 3.2-DNV

Chargenumber stamped in the material. White circle

around chargenumber

ARTICLE GROUP 144


144006 3,00 X 1500 X 5000 MM 180.00144007 3,00 X 1800 X 4000 MM 173.00144008 3,00 X 1800 X 5000 MM 216.00144009 3,00 X 1800 X 6000 MM 259.00144010 3,00 X 2000 X 6000 MM 288.00


5/54

STEEL

www.norskstaal.no4

144030 4,00 X 1500 X 5000 MM 240.00144032 4,00 X 1500 X 6000 MM 288.00144035 4,00 X 1800 X 5000 MM 288.00

144040 4,00 X 1800 X 6000 MM 346.00144041 4,00 X 2000 X 6000 MM 384.00144042 4,00 X 2500 X 5000 MM 400.00

144065 5,00 X 1500 X 6000 MM 360.00144070 5,00 X 1800 X 5000 MM 360.00144075 5,00 X 1800 X 6000 MM 432.00144085 5,00 X 2000 X 5000 MM 400.00144090 5,00 X 2000 X 6000 MM 480.00144093 5,00 X 2500 X 6000 MM 600.00144094 5,00 X 2500 X 8000 MM 800.00

144124 6,00 X 1500 X 6000 MM 432.00144140 6,00 X 1800 X 6000 MM 518.00


144157 6,50 X 2500 X 8000 MM 1040.00

144164 7,00 X 2000 X 6000 MM 672.00144166 7,00 X 2500 X 6000 MM 840.00144168 7,00 X 2500 X 8000 MM 1120.00

144183 7,50 X 2500 X 8000 MM 1200.00

144205 8,00 X 1500 X 6000 MM 576.00144230 8,00 X 2000 X 6000 MM 768.00144240 8,00 X 2000 X 8000 MM 1024.00144260 8,00 X 2500 X 6000 MM 960.00144264 8,00 X 2500 X 8000 MM 1280.00144270 8,00 X 2500 X 12000 MM 1920.00


144327 9,50 X 2500 X 8000 MM 1520.00


144401 11,00 X 2000 X 6000 MM 1056.00144402 11,00 X 2000 X 8000 MM 1408.00144404 11,00 X 2500 X 8000 MM 1760.00

144425 12,00 X 1500 X 6000 MM 864.00


144453 12,50 X 2500 X 8000 MM 2000.00

144456 13,00 X 2000 X 6000 MM 1248.00144457 13,00 X 2000 X 8000 MM 1664.00144459 13,00 X 2500 X 8000 MM 2080.00

144461 13,00 X 2500 X 12000 MM 3120.00

144468 14,00 X 2000 X 6000 MM 1344.00144469 14,00 X 2000 X 8000 MM 1792.00144471 14,00 X 2500 X 8000 MM 2240.00


144529 16,00 X 2000 X 6000 MM 1536.00

144535 16,00 X 2500 X 8000 MM 2560.00144540 16,00 X 2500 X 12000 MM 3840.00

144547 18,00 X 2000 X 6000 MM 1728.00144550 18,00 X 2500 X 8000 MM 2880.00144552 18,00 X 2500 X 12000 MM 4320.00

144562 20,00 X 1000 X 2000 MM 320.00144565 20,00 X 1250 X 2500 MM 500.00144568 20,00 X 1500 X 3000 MM 720.00144571 20,00 X 1500 X 6000 MM 1440.00144580 20,00 X 2000 X 6000 MM 1920.00144583 20,00 X 2000 X 8000 MM 2560.00144586 20,00 X 2500 X 6000 MM 2400.00

144589 20,00 X 2500 X 8000 MM 3200.00144591 20,00 X 2500 X 12000 MM 4800.00

144601 22,00 X 2500 X 8000 MM 3520.00



144673 35,00 X 2000 X 6000 MM 3360.00144679 35,00 X 2500 X 8000 MM 5600.00


144712 45,00 X 2000 X 6000 MM 4320.00144713 45,00 X 2500 X 8000 MM 7200.00

144715 50,00 X 1000 X 2000 MM 800.00144730 50,00 X 2000 X 6000 MM 4800.00144736 50,00 X 2500 X 8000 MM 8000.00

144748 60,00 X 2000 X 6000 MM 5760.00

Article no. Dimension Kg/plateArticle no. Dimension Kg/plate


6/54

STEEL

www.norskstaal.no 5

144761 65,00 X 2000 X 6000 MM 6240.00

144773 70,00 X 2000 X 6000 MM 6720.00

144787 80,00 X 1500 X 3000 MM 2880.00144792 80,00 X 2000 X 6000 MM 7680.00

Steel plates for pressurepurposes P355NL2

Acc. to EN 10 028.

Impact tested at -50 degr.C

Tolerances acc. to NS-EN 10 029 Class C

Inspection certificate acc. to EN 10 204 3.2-DNV


around chargenumber

ARTICLE GROUP 148


148040 8,00 X 2500 X 8000 MM 1312.00

148060 10,00 X 2500 X 8000 MM 1640.00

148080 12,00 X 2500 X 8000 MM 1968.00

148100 15,00 X 2500 X 8000 MM 2460.00

148120 20,00 X 2500 X 8000 MM 3280.00

Steel plates S355J2+NAcc. to EN 10 025-2

Carbonequivalent (CEV) to be stated in the certificate

Tolerances and flatnes acc. to EN 10 029, Class A

Inspection certificate acc. to EN 10 204-3.1 forthicknesses under 50 mm. Inspection certificate acc. to

EN 10 204 3.2-DNV for thicknesses over 50 mm


around chargenumber

ARTICLE GROUP 150


150015 3,00 X 1250 X 2500 MM 75.00150020 4,00 X 1250 X 2500 MM 100.00150030 5,00 X 1250 X 2500 MM 125.00150040 5,00 X 2000 X 6000 MM 480.00150045 6,00 X 1000 X 2000 MM 96.00150050 6,00 X 1250 X 2500 MM 150.00150055 6,00 X 1500 X 3000 MM 216.00150065 6,00 X 2000 X 6000 MM 576.00


150125 10,00 X 1000 X 2000 MM 160.00



150235 15,00 X 1250 X 2500 MM 375.00


150270 16,00 X 1250 X 2500 MM 400.00150285 16,00 X 2500 X 8000 MM 2560.00


Steel plates for pressurepurposes P265GH

Acc. to EN 10 028-2 ASME 516 GR. 60/

ASME SEC- 2 part A. ADWI, TRB 100.

Proof stress tested Rp 0,2 acc. to EN 10 002 at

300 degr.C

Tolerances and flatness acc. to EN 10 029 Class C

Inspection certificate acc. to 10 204 3.2-DNVChargenumber stamped in the material. White

circle around chargenumber

ARTICLE GROUP 140


140004 6,00 X 2000 X 6000 MM 576.00

140014 8,00 X 2000 X 6000 MM 768.00

140032 10,00 X 2000 X 6000 MM 960.00

140048 28,00 X 2500 X 4000 MM 2240.00



7/54

STEEL

www.norskstaal.no6


150405 25,00 X 1250 X 2500 MM 625.00150410 25,00 X 1500 X 3000 MM 900.00150420 25,00 X 2000 X 6000 MM 2400.00


150512 35,00 X 1500 X 3000 MM 1260.00


150575 45,00 X 1500 X 3000 MM 1620.00


150650 60,00 X 1500 X 3000 MM 2160.00150655 60,00 X 2000 X 6000 MM 5760.00150657 60,00 X 2200 X 5100 MM 5386.00

150660 65,00 X 1500 X 3000 MM 2340.00

150690 70,00 X 1500 X 3000 MM 2520.00150700 70,00 X 2000 X 6000 MM 6720.00

150730 80,00 X 1500 X 3000 MM 2880.00150735 80,00 X 2000 X 6000 MM 7680.00150737 80,00 X 2500 X 5000 MM 8000.00

150745 90,00 X 2000 X 6000 MM 8640.00

150750 100,00 X 1500 X 3000 MM 3600.00150754 100,00 X 2000 X 6000 MM 9600.00

150756 110,00 X 2000 X 5000 MM 8800.00

150762 115,00 X 2000 X 5000 MM 9200.00

150766 120,00 X 2000 X 5000 MM 9600.00

150774 125,00 X 2000 X 5000 MM 10000.00

150805 130,00 X 1250 X 2500 MM 3250.00150810 130,00 X 2000 X 4000 MM 8320.00

150820 140,00 X 1250 X 2500 MM 3500.00150824 140,00 X 2000 X 4000 MM 8960.00

150830 150,00 X 1250 X 2500 MM 3750.00150836 150,00 X 2000 X 4000 MM 9600.00

150845 170,00 X 2000 X 3000 MM 8160.00

150850 200,00 X 1250 X 2500 MM 5000.00150855 200,00 X 2000 X 3000 MM 9600.00


8/54

STEEL

www.norskstaal.no 7

Steel plates NVE 36Acc. to DNV Offshore Codes,

Classification of Offshore Units Jan. 2001 and Rules

for Classification of ships Jan. 2005

ModifiedC max 0,16 CEV max 0,42 or by agreement

max CEV 0,41

Impact tested at -40 degr.C min. 50 Joule/longtested

Thickness tolerances EN 10 029 Class B

Remaining tolerances acc. to DNV-rules

Inspection certificate acc. to EN 10 204 3.2-DNVChargenumber stamped in the material. White circle

around chargenumber

ARTICLE GROUP 146


146002 6,00 X 2000 X 6000 MM 576.00146003 6,00 X 2500 X 8000 MM 960.00

146005 7,00 X 2500 X 8000 MM 1120.00

146006 8,00 X 2000 X 6000 MM 768.00146007 8,00 X 2500 X 8000 MM 1280.00146009 8,00 X 2500 X 12000 MM 1920.00

146011 9,00 X 2500 X 8000 MM 1440.00

146008 10,00 X 2000 X 6000 MM 960.00146010 10,00 X 2500 X 8000 MM 1600.00

146012 10,00 X 2500 X 12000 MM 2400.00146013 10,00 X 3000 X 12000 MM 2880.00

146014 11,00 X 2500 X 8000 MM 1760.00


146025 13,00 X 2500 X 8000 MM 2080.00

146027 15,00 X 2500 X 12000 MM 3600.00146028 15,00 X 3000 X 12000 MM 4320.00

146029 15,00 X 2000 X 6000 MM 1440.00146030 15,00 X 2500 X 8000 MM 2400.00

146031 16,00 X 2000 X 6000 MM 1536.00146032 16,00 X 2500 X 8000 MM 2560.00

146035 18,00 X 2500 X 8000 MM 2880.00


146061 22,00 X 2500 X 8000 MM 3520.00


146082 30,00 X 1500 X 6000 MM 2160.00146084 30,00 X 2000 X 6000 MM 2880.00146085 30,00 X 2500 X 8000 MM 4800.00

146086 30,00 X 3000 X 12000 MM 8640.00

146090 35,00 X 2000 X 6000 MM 3360.00146091 35,00 X 2500 X 8000 MM 5600.00

146095 40,00 X 2000 X 6000 MM 3840.00146105 40,00 X 2500 X 8000 MM 6400.00

146106 45,00 X 2500 X 8000 MM 7200.00146108 45,00 X 2000 X 6000 MM 4320.00

146115 50,00 X 2000 X 6000 MM 4800.00146121 50,00 X 2500 X 8000 MM 8000.00

146130 60,00 X 2000 X 6000 MM 5760.00146132 60,00 X 2500 X 8000 MM 9600.00

146140 65,00 X 2000 X 6000 MM 6240.00

146148 70,00 X 2000 X 6000 MM 6720.00

146156 75,00 X 2000 X 6000 MM 7200.00

146162 80,00 X 2000 X 6000 MM 7680.00

146170 90,00 X 2000 X 6000 MM 8640.00

146190 100,00 X 2000 X 6000 MM 9600.00



9/54

STEEL

www.norskstaal.no8

Steel plates S355G10 + N/MNORSOK M-120 rev. 5,

Z35 for thicknesses 25 mm

MDS Y20 Rev. 5 and acc. to EN 10 225

Tolerances and flatness acc. to EN 10 029Inspection certificate acc. to EN 10 204-3.2 DNV/Lloyds

Chargenumber stamped in both ends. White circle

around chargenumber.

ARTICLE GROUP 189


189007 8,00 X 2500 X 8000 MM 1280.00189011 10,00 X 2500 X 12000 MM 2400.00189014 12,00 X 2500 X 12000 MM 2880.00189017 15,00 X 2500 X 12000 MM 3600.00189018 16,00 X 2500 X 12000 MM 3840.00189027 20,00 X 2500 X 12000 MM 4800.00189037 25,00 X 2500 X 12000 MM 6000.00189047 30,00 X 2500 X 12000 MM 7200.00189050 35,00 X 2500 X 12000 MM 8400.00189057 40,00 X 2500 X 12000 MM 9600.00189066 50,00 X 2500 X 8000 MM 8000.00189075 60,00 X 2000 X 6000 MM 5760.00189080 70,00 X 2000 X 6000 MM 6720.00189090 80,00 X 2000 X 6000 MM 7680.00189110 100,00 X 2000 X 4000 MM 6400.00189120 110,00 X 2000 X 4000 MM 7040.00189130 120,00 X 2000 X 4000 MM 7680.00189131 120,00 X 2000 X 5000 MM 9600.00


Steel plates DOMEX S355MCD/ELazerplatesPickled and lightly oiled

High yield strength steel acc. to EN 10 149-2Uniqe properties regarding cold forming, tight bend

radius and suitable for lazer cutting

Re min. 355N/mm2, Impact tested at -20 gr. C

Tolerances and flatness acc. to EN 10 051Inspection certificate acc. to EN 10 204-3.1Quality marked along one side


envelopes

ARTICLE GROUP 128


128020 2,00 X 1000 X 2000 MM 32.00128022 2,00 X 1250 X 2500 MM 50.00128025 2,50 X 1250 X 2500 MM 62.50

128030 3,00 X 1250 X 2500 MM 75.00128035 3,00 X 1500 X 3000 MM 108.00

128040 4,00 X 1000 X 2000 MM 64.00

128045 4,00 X 1250 X 2500 MM 100.00128048 5,00 X 1000 X 2000 MM 80.00

128058 6,00 X 1000 X 2000 MM 96.00128062 6,00 X 1500 X 3000 MM 216.00

128078 8,00 X 1000 X 2000 MM 128.00128082 8,00 X 1500 X 3000 MM 288.00

128092 10,00 X 1500 X 3000 MM 360.00

128102 12,00 X 1500 X 3000 MM 432.00

Steel plates DOMEX S355MCD/E/BLazerplatesHigh yield strength steel acc. to EN 10 149 -2Uniqe properties regarding cold forming, tight bendradius and suitable for lazer cutting

Re min. 355N/mm2

Impact tested: MCE -40 gr. C, MCD -20 gr. C,

MCB without testing

Tolerances and flatness acc. to EN 10 051

Inspection certificate acc. to EN 10 204-3.1Quality marked along one side

ARTICLE GROUP 151


151015 3,00 X 1250 X 2500 MM MCE 75.00151017 3,00 X 1500 X 3000 MM MCE 108.00

151020 4,00 X 1250 X 2500 MM MCE 100.00151023 4,00 X 1500 X 3000 MM MCE 144.00

151025 5,00 X 1000 X 2000 MM MCE 80.00151030 5,00 X 1250 X 2500 MM MCE 125.00151033 5,00 X 1500 X 3000 MM MCE 180.00




151165 12,00 X 1000 X 2000 MM MCD 192.00151170 12,00 X 1250 X 2500 MM MCD 300.00151175 12,00 X 1500 X 3000 MM MCD 432.00

151180 15,00 X 1250 X 2500 MM MCB 375.00

151185 15,00 X 1500 X 3000 MM MCB 540.00



10/54

STEEL

www.norskstaal.no 9

Steel plates DOMEX S500MCDLazerplatesPickled and lightly oiled

High yield strength steel acc. to EN 10 149-2Uniqe properties regarding cold forming, tight bend

radius and suitbale for lazer cuttingRe min. 500N/mm2, Impact tested at -20 degr.C


Inspection certificate acc. to EN 10 204-3.1



envelopes

ARTICLE GROUP 173


173012 3 X 1250 X 2500 MM 75.00

173022 4 X 1500 X 3000 MM 144.00

173035 5 X 1500 X 3000 MM 180.00

173052 6 X 1500 X 3000 MM 216.00

173062 8 X 1500 X 3000 MM 288.00

173102 10 X 1500 X 3000 MM 360.00

Steel plates DOMEX S650MCDLazerplatesHigh yield strength steel acc. to EN 10 149-2

Uniqe properties regarding cold forming, tight bend

radius and suitbale for lazer cutting

Re min. 650N/mm2, Impact tested at -20 degr.CTolerances and flatness acc. to EN 10 051




envelopes

ARTICLE GROUP 174


174025 3,00 X 1250 X 2500 MM 75.00

174040 4,00 X 1250 X 2500 MM 100.00174045 4,00 X 1500 X 5000 MM 240.00

174050 5,00 X 1250 X 2500 MM 125.00174052 5,00 X 1500 X 5000 MM 300.00

174054 6,00 X 1250 X 2500 MM 150.00174055 6,00 X 1500 X 3000 MM 216.00174056 6,00 X 1500 X 5000 MM 360.00

174057 8,00 X 1250 X 2500 MM 200.00174060 8,00 X 1500 X 5000 MM 480.00

Steel plates DOMEX S700MCDLazerplatesHigh yield strength steel acc. to EN 10 149-2

Uniqe properties regarding cold forming, tight bendradius and suitbale for lazer cutting

Re min. 650N/mm2, Impact tested at -20 degr.CTolerances and flatness acc. to EN 10 051




envelopes

ARTICLE GROUP 175


175018 4 X 1000 X 2000 MM 64.00

175040 6 X 1000 X 2000 MM 96.00175050 6 X 1500 X 5000 MM 360.00

Steel plates DOMEX 355W(COR-TEN A / S355J2WP)

Acc. to EN 10 025-5Structural steel with improved atmospheric

corrosion resistance



ARTICLE GROUP 164




11/54

STEEL

www.norskstaal.no10

Steel plates S420G2 + M/QNORSOK M-120 Rev. 5, MDS Y-30 Rev. 5

and acc. to EN 10 225

Z 35 for thicknesses 25 mm

For thicknesses over 100 mm, the plates are onlydelivered Q (quenced and tempered)


Inspection certificate acc. to EN 10 204-3.2 DNV/Lloyds

Chargenumber stamped in both ends

White circle painted around chargenumber

ARTICLE GROUP 191


191085 8,00 X 2500 X 10000 MM 1600.00

191100 10,00 X 2500 X 12000 MM 2400.00

191110 12,00 X 2500 X 12000 MM 2880.00

191150 15,00 X 2500 X 12000 MM 3600.00

191160 16,00 X 2500 X 12000 MM 3840.00

191200 20,00 X 2500 X 12000 MM 4800.00

191250 25,00 X 2500 X 12000 MM 6000.00

191300 30,00 X 2500 X 12000 MM 7200.00

191350 35,00 X 2500 X 12000 MM 8400.00

191405 40,00 X 2500 X 12000 MM 9600.00

191450 45,00 X 2500 X 8000 MM 7200.00

191500 50,00 X 2500 X 8000 MM 8000.00

191550 55,00 X 2500 X 8000 MM 8800.00

191600 60,00 X 2500 X 6000 MM 7200.00

191700 70,00 X 2500 X 6000 MM 8400.00

191800 80,00 X 2500 X 6000 MM 9600.00

191890 90,00 X 2500 X 6000 MM 10800.00

191900 100,00 X 2500 X 6000 MM 12000.00

191920 120,00 X 2000 X 4000 MM 7680.00

191930 130,00 X 2000 X 4000 MM 8320.00

191940 140,00 X 2000 X 4000 MM 8960.00

191950 150,00 X 2000 X 4000 MM 9600.00

Steel plates WELDOX 700E/S690QLExtra high strength structural steel,

quenched and tempered acc. to EN 10 025-6

Impact tested at -40 gr.C.

Tolerances: thickness acc. to EN 10 029 class A or withmore narrow tolerances (AccuRollTech)

Tolerances and flatness acc. to EN 10 029 class N

Inspection certificare acc. to EN 10 204-3.2-DNV

Shot blasted and primed on both sides with

redbrown primer

Chargenumber stamped in the material. White circlearound chargenumber

ARTICLE GROUP 171


171135 6,00 X 1500 X 2500 MM 180.00171136 6,00 X 1500 X 3000 MM 216.00171140 6,00 X 2500 X 6000 MM 720.00

171155 8,00 X 1500 X 2500 MM 240.00171160 8,00 X 2500 X 6000 MM 960.00


171180 12,00 X 1500 X 2500 MM 360.00171182 12,00 X 1500 X 5000 MM 720.00




171225 25,00 X 1500 X 2500 MM 750.00171230 25,00 X 1500 X 5000 MM 1500.00171245 25,00 X 2500 X 6000 MM 3000.00

171260 30,00 X 1500 X 2500 MM 900.00171275 30,00 X 2500 X 6000 MM 3600.00

171290 40,00 X 1500 X 2500 MM 1200.00171305 40,00 X 2500 X 6000 MM 4800.00

171320 50,00 X 1500 X 2500 MM 1500.00171332 50,00 X 2500 X 6000 MM 6000.00

171350 60,00 X 1500 X 2500 MM 1800.00


12/54

STEEL

www.norskstaal.no 11

171355 60,00 X 2000 X 4000 MM 3840.00171360 60,00 X 2500 X 6000 MM 7200.00

171365 70,00 X 1500 X 2500 MM 2100.00171370 70,00 X 2500 X 6000 MM 8400.00

171375 80,00 X 2000 X 4000 MM 5120.00171380 80,00 X 2500 X 6000 MM 9600.00

171390 90,00 X 2000 X 4000 MM 5760.00

171400 100,00 X 2000 X 4000 MM 6400.00

171410 110,00 X 2000 X 4000 MM 7040.00

171420 120,00 X 2000 X 4000 MM 7680.00

Abrasion resistant steel platesHardox 450Well suited for welding

Brinell hardness: approx. 450 HB (425-475 HB)

Thickness tolerances acc. to EN 10 029 class A

or with more narrow tolerances (AccuRollTech)Tolerances and flatness acc. to EN 10 029 class N



redbrown primer


around chargenumberOne side of plate marked HARDOX 450

For article number 166262 and 166272 we reserve the

right to stock Hardox 450 and/or Hardox 400

ARTICLE GROUP 166


166040 4,00 X 2500 X 6000 MM 480.00

166050 5,00 X 2500 X 6000 MM 600.00

166055 6,00 X 1500 X 2500 MM 180.00

166060 6,00 X 2500 X 6000 MM 720.00

166070 8,00 X 1500 X 2500 MM 240.00166078 8,00 X 2500 X 6000 MM 960.00

166090 10,00 X 1500 X 2500 MM 300.00166100 10,00 X 2500 X 6000 MM 1200.00166110 10,00 X 2500 X 7000 MM 1400.00


166135 16,00 X 1500 X 2500 MM 480.00166138 16,00 X 2500 X 6000 MM 1920.00

166145 20,00 X 1500 X 2500 MM 600.00166148 20,00 X 2500 X 6000 MM 2400.00

166165 25,00 X 1500 X 2500 MM 750.00166168 25,00 X 2500 X 6000 MM 3000.00

166195 30,00 X 1500 X 2500 MM 900.00166198 30,00 X 2500 X 6000 MM 3600.00166200 30,00 X 2500 X 7000 MM 4200.00

166215 40,00 X 1500 X 2500 MM 1200.00166218 40,00 X 2500 X 6000 MM 4800.00

166230 45,00 X 2000 X 4000 MM 2880.00

166248 50,00 X 1500 X 2500 MM 1500.00166250 50,00 X 2500 X 6000 MM 6000.00

166262 60,00 X 2000 X 4000 MM 3840.00

166265 63,00 X 1500 X 8200 MM 6199.00

166272 70,00 X 2000 X 4000 MM 4480.00

Abrasion resistant steel platesHardox 500Well suited for welding

Brinell hardness: 470-530 HB 4-26 mm

450-540 HB 26,1 - 80 mm

Thickness tolerances acc. to EN 10 029 class A or with

more narrow tolerances (AccuRollTech)

Tolerances and flatness acc. to EN 10 029 class NInspection certificate acc. to EN 10 204-3.1


redbrown primer.


around chargenumber

ARTICLE GROUP 168


168010 10,00 X 1500 X 3000 MM 360.00

168012 12,00 X 1500 X 2500 MM 360.00

168030 16,00 X 1500 X 3000 MM 576.00

168050 20,00 X 1500 X 3000 MM 720.00

168060 25,00 X 1500 X 3000 MM 900.00168073 25,00 X 2500 X 6000 MM 3000.00

168081 30,00 X 2500 X 6000 MM 3600.00

168085 40,00 X 1500 X 3000 MM 1440.00168088 40,00 X 2500 X 6400 MM 5120.00

168090 50,00 X 1500 X 3000 MM 1800.00

168100 50,00 X 2000 X 4000 MM 3200.00

168130 60,00 X 2000 X 4000 MM 3840.00

Article no. Dimension Kg/plate Article no. Dimension Kg/plate


13/54

STEEL

www.norskstaal.no12

Steel Checker plates S235JRAcc. to EN 10 025-2

Delivered with standard checkered pattern

Tolerances acc. to EN 10 051

Test report acc. to EN 10 204-2.2

ARTICLE GROUP 152


152003 3,00 X 1000 X 2000 MM 60.00152005 3,00 X 1250 X 2500 MM 94.00

Steel Tear plates S235JRAcc. to EN 10 025-2

Delivered with standard teardrop pattern

Tolerances acc. to EN 10 051Inspection certificate acc. to EN 10 204-3.1

ARTICLE GROUP 153


153140 5,00 X 1000 X 2000 MM 84.00153150 5,00 X 1250 X 2500 MM 131.00

153200 6,00 X 1000 X 2000 MM 102.00153210 6,00 X 1250 X 2500 MM 159.00

Steel Tear plates NVAThickness tolerances acc. to DNV-rules

Remaining tolerances and flatnes acc. toEN 10 029 Klasse B

Inspection certificate acc. to EN 10 204-3.2 DNV

Chargenumber stamped in the material

ARTICLE GROUP 155




155290 8,00 X 1500 X 6000 MM 603.00155310 8,00 X 2000 X 6000 MM 804.00155320 8,00 X 2500 X 8000 MM 1340.00



14/54

STEEL


Steel rounds S235JRAcc. to EN 10 025-2


Length tolerances +/-100 mm


ARTICLE GROUP 19

Article no. Dimension Kg/m Lengths (m)

19018 6 MM X 0.23 6

19030 8 MM X 0.40 6

19040 10 MM X 0.63 6

19045 12 MM X 0.91 6

19050 16 MM X 1.61 6

19055 20 MM X 2.51 619060 22 MM X 3.04 619065 25 MM X 3.93 6

19070 30 MM X 5.66 619075 32 MM X 6.44 619080 35 MM X 7.70 6

19090 40 MM X 10.10 6

19148 50 MM X 15.70 6

Steel rounds NVATolerances acc. to EN 10 060


Inspection certificate acc. to EN 10 204-3.2-DNV

ARTICLE GROUP 1


1064 16 MM X 1.61 6

1071 19 MM X 2.27 6

1078 20 MM X 2.51 61085 22 MM X 3.04 61092 25 MM X 3.93 6

1109 30 MM X 5.66 6

1148 50 MM X 15.70 6

1183 75 MM X 35.40 6

1185 80 MM X 40.20 6

Steel rounds/shafts S355J2+N(XM/M520/IM) acc. to EN 10 025-2



Inspection certificate acc. to EN 10 204-3.2-DNVImpact tested at - 20 degrees C, min 27 J

Chargenumber and DNV stamped on the ends of

rounds/shafts

ARTICLE GROUP 73

Article no. Dimension Kg/m From (m)To (m)

73070 70 MM X 30.80 6 7.573075 75 MM X 35.40 6 7.5

73080 80 MM X 40.20 6 7.573085 85 MM X 45.40 6 7.5

73090 90 MM X 50.90 6 7.5

73100 100 MM X 62.90 6 7.573105 105 MM X 69.30 6 7.573110 110 MM X 76.10 6 7.573115 115 MM X 83.10 6 7.5

73120 120 MM X 90.50 6 7.573125 125 MM X 98.20 6 7.5

73130 130 MM X 106.00 6 7.5

73140 140 MM X 123.00 6 7.5

73150 150 MM X 141.00 6 7.5

73160 160 MM X 161.00 6 7.5

73170 170 MM X 182.00 6 7.5

73180 180 MM X 204.00 6 7.5

73190 190 MM X 227.00 6 7.5

73200 200 MM X 251.00 6 7.573210 210 MM X 277.00 6 7.5

73220 220 MM X 304.00 6 7.573230 230 MM X 333.00 6 7.573240 240 MM X 362.00 6 7.573250 250 MM X 385.30 6 7.573260 260 MM X 425.00 6 7.573280 280 MM X 493.00 6 7.573290 290 MM X 532.00 6 7.5

73300 300 MM X 566.00 6 7.573320 320 MM X 648.00 6 7.573330 330 MM X 684.00 6 7.573350 350 MM X 770.00 6 7.5


15/54

STEEL

www.norskstaal.no14

Steel rounds S355JOAcc. to EN 10 025-2



Impact tested at 0 degrees C, min 27 JInspection certificate acc. to EN 10 204-3.1

Under 50 mm: chargenumber stamped on tags

Above 50 mm chargenumber stamped on the end of

rounds

ARTICLE GROUP 72


72016 16 MM X 1.61 6

72020 20 MM X 2.51 672025 25 MM X 3.93 6

72030 30 MM X 5.66 672032 32 MM X 6.44 672035 35 MM X 7.70 672038 38 MM X 9.08 6

72040 40 MM X 10.10 672045 45 MM X 12.70 6

72050 50 MM X 15.70 672055 55 MM X 19.00 6

72060 60 MM X 22.60 6

72065 65 MM X 26.60 6

Steel rounds/shafts 34CrNiMo6Acc. to EN 10 083-1 or acc. to SS2541-3

Quenched and tempered

Impact tested at -20 gr.C



ARTICLE GROUP 75


75016 16 MM X 1.61 3 3

75020 20 MM X 2.52 4 675025 25 MM X 3.93 4 6

75030 30 MM X 5.66 4 675032 32 MM X 6.44 4 675035 35 MM X 7.70 4 675038 38 MM X 9.08 4 6

75040 40 MM X 10.10 4 675045 45 MM X 12.80 4 6

75050 50 MM X 15.70 4 6

75060 60 MM X 22.60 4 675065 65 MM X 26.50 4 6

75070 70 MM X 30.80 4 675075 75 MM X 35.40 4 675080 80 MM X 40.30 4 6

75090 90 MM X 50.90 4 6

75100 100 MM X 62.90 4 675110 110 MM X 76.10 4 6

75120 120 MM X 90.60 4 675125 125 MM X 98.20 4 6

75130 130 MM X 106.00 4 6

75140 140 MM X 123.00 4 6

75150 150 MM X 142.00 4 6

75160 160 MM X 161.00 4 6

75180 180 MM X 204.00 4 6

75200 200 MM X 252.00 4 6

Steel half rounds NVATolerances acc. to DIN 1018

Length tolerances -0/+100 mm


ARTICLE GROUP 5


5007 76 X 38 MM 18.23 6

5013 50 X 25 MM 7.85 6

5016 60 X 30 MM 11.30 6

Steel squares S235JRAcc. to EN 10 025-2Tolerances acc. to EN 10 059

Length tolerances +/-100 mmTest report acc. to EN 10 204-2.2

ARTICLE GROUP 2


2010 6 MM X 4-KT 0.29 6

2025 8 MM X 4-KT 0.51 6

2030 10 MM X 4-KT 0.80 6

2040 12 MM X 4-KT 1.15 6

2047 16 MM X 4-KT 2.05 6



16/54

STEEL


2050 20 MM X 4-KT 3.20 62057 22 MM X 4-KT 3.88 62064 25 MM X 4-KT 5.00 6

2069 30 MM X 4-KT 7.21 6

2078 40 MM X 4-KT 12.80 6

2092 50 MM X 4-KT 20.00 6

2099 60 MM X 4-KT 28.80 6

2134 100 MM X 4-KT 80.10 6

Steel flats S235JR

Acc. to EN 10 025-2Tolerances acc. to EN 10 058



ARTICLE GROUP 20


20015 16 X 3 MM 0.38 420022 20 X 3 MM 0.48 420029 25 X 3 MM 0.60 420037 30 X 3 MM 0.72 420043 40 X 3 MM 0.96 4

20057 50 X 3 MM 1.20 420092 75 X 3 MM 1.80 420112 100 X 3 MM 2.40 4

20180 16 X 5 MM 0.64 620193 20 X 5 MM 0.80 620215 25 X 5 MM 1.00 620222 30 X 5 MM 1.20 620227 35 X 5 MM 1.40 620230 40 X 5 MM 1.60 620235 50 X 5 MM 2.00 620238 60 X 5 MM 2.40 620241 70 X 5 MM 2.80 620245 80 X 5 MM 3.20 6



20318 20 X 8 MM 1.28 620320 25 X 8 MM 1.60 6

20323 30 X 8 MM 1.92 620325 40 X 8 MM 2.56 620328 50 X 8 MM 3.20 6

20330 60 X 8 MM 3.84 620336 70 X 8 MM 4.48 620341 75 X 8 MM 4.80 620346 80 X 8 MM 5.12 620356 100 X 8 MM 6.41 620361 120 X 8 MM 7.69 620366 130 X 8 MM 8.33 620376 150 X 8 MM 9.61 6


20416 60 X 10 MM 4.80 620421 65 X 10 MM 5.20 620426 70 X 10 MM 5.60 620431 75 X 10 MM 6.01 620436 80 X 10 MM 6.41 620441 90 X 10 MM 7.21 620446 100 X 10 MM 8.01 620451 120 X 10 MM 9.61 620461 150 X 10 MM 12.00 6



20631 40 X 20 MM 6.41 620636 50 X 20 MM 8.01 620641 60 X 20 MM 9.61 620661 80 X 20 MM 12.80 620671 100 X 20 MM 16.00 620676 120 X 20 MM 19.20 620691 150 X 20 MM 24.00 6

20711 50 X 25 MM 10.00 620766 150 X 25 MM 30.00 6

20771 50 X 30 MM 12.00 620801 100 X 30 MM 24.00 6

20806 130 X 30 MM 31.20 6

20881 100 X 50 MM 40.00 6

Article no. Dimension Kg/m Lengths (m)Article no. Dimension Kg/m Lengths (m)


17/54

STEEL

www.norskstaal.no16

Steel flats NVATolerances acc. to EN 10 058



ARTICLE GROUP 3



3197 20 X 6 MM 0.96 63203 25 X 6 MM 1.20 63206 30 X 6 MM 1.44 63216 40 X 6 MM 1.92 63226 50 X 6 MM 2.40 63231 60 X 6 MM 2.88 63236 65 X 6 MM 3.12 63241 70 X 6 MM 3.36 63246 75 X 6 MM 3.60 63251 80 X 6 MM 3.84 63256 90 X 6 MM 4.32 63261 100 X 6 MM 4.80 6

3266 120 X 6 MM 5.77 63281 150 X 6 MM 7.21 6

3288 20 X 8 MM 1.28 63293 25 X 8 MM 1.60 63298 30 X 8 MM 1.92 63311 40 X 8 MM 2.56 63321 50 X 8 MM 3.20 63326 60 X 8 MM 3.84 63331 65 X 8 MM 4.16 63336 70 X 8 MM 4.48 63341 75 X 8 MM 4.80 63346 80 X 8 MM 5.12 63351 90 X 8 MM 5.77 6



3431 75 X 10 MM 6.01 63436 80 X 10 MM 6.41 63441 90 X 10 MM 7.21 63446 100 X 10 MM 8.01 63451 120 X 10 MM 9.61 63456 130 X 10 MM 10.40 6

3458 140 X 10 MM 11.20 63461 150 X 10 MM 12.00 6

3475 30 X 12 MM 2.88 63477 35 X 12 MM 3.36 6.33481 40 X 12 MM 3.84 63491 50 X 12 MM 4.80 63496 60 X 12 MM 5.77 63506 70 X 12 MM 6.73 63511 75 X 12 MM 7.21 63516 80 X 12 MM 7.69 63526 100 X 12 MM 9.61 63531 120 X 12 MM 11.50 63536 130 X 12 MM 12.50 63541 150 X 12 MM 14.40 6

3549 30 X 15 MM 3.60 6

3551 35 X 15 MM 4.20 5.33556 40 X 15 MM 4.80 63566 50 X 15 MM 6.01 63571 60 X 15 MM 7.21 63576 65 X 15 MM 7.81 63578 70 X 15 MM 8.41 63581 75 X 15 MM 9.01 63586 80 X 15 MM 9.61 63596 100 X 15 MM 12.00 63601 120 X 15 MM 14.40 63606 130 X 15 MM 15.60 63616 150 X 15 MM 18.00 6

3631 40 X 20 MM 6.41 6



3771 50 X 30 MM 12.00 63791 80 X 30 MM 19.20 63801 100 X 30 MM 24.00 63811 150 X 30 MM 36.00 6

3831 70 X 40 MM 22.40 6

3851 100 X 40 MM 32.00 63866 150 X 40 MM 48.00 6

3871 75 X 50 MM 30.00 63881 100 X 50 MM 40.00 6



18/54

STEEL


Steel flats S355J2Acc. to EN 10 025-2




ARTICLE GROUP 9


9020 40 X 6 MM 1.92 69025 50 X 6 MM 2.40 69030 60 X 6 MM 2.88 69040 100 X 6 MM 4.80 6



9180 100 X 12 MM 9.61 69190 120 X 12 MM 11.50 6

9200 150 X 12 MM 14.40 6

Steel flat rails S355JOAcc. to EN 10 025-2

Delivered with 2 round corners


ARTICLE GROUP 33

Article no. Dimension Kg/m Lengths (m) Kg/Length

33008 30 X 50 MM 11.80 10 118.00

33015 40 X 60 MM 19.00 10 190.00

Steel crane railsAcc. to DIN 536

Tensile strength min. 690N/mm2

Delivered with straight ends

Length tolerances +/-50 mmDeclaration of compliance with the order acc. to EN 10 204-2.1

ARTICLE GROUP 58


58045 A 45 22.70 12 272.4058055 A 55 32.70 12 392.4058065 A 65 44.40 12 532.8058075 A 75 57.80 12 693.6058100 A 100 76.70 12 920.4058120 A 120 103.40 12 1240.80

Steel wide flats NVARolled or cut from plate

Toleranes acc. to DIN 59 200 or

NS-EN 10 029 at our discretion


ARTICLE GROUP 160


160029 180 X 6 MM 8.64 6160036 200 X 6 MM 9.60 6160043 250 X 6 MM 12.00 6160050 300 X 6 MM 14.40 6

160064 180 X 8 MM 11.52 6160071 200 X 8 MM 12.80 6160078 250 X 8 MM 16.00 6160085 300 X 8 MM 19.20 6



160227 200 X 15 MM 24.00 6160229 250 X 15 MM 30.00 6160230 300 X 15 MM 36.00 6

160295 180 X 20 MM 28.80 6160302 200 X 20 MM 32.00 6160309 250 X 20 MM 40.00 6160316 300 X 20 MM 48.00 6

160351 200 X 25 MM 40.00 6160358 250 X 25 MM 50.00 6160365 300 X 25 MM 60.00 6

160386 200 X 30 MM 48.00 6

160393 250 X 30 MM 60.00 6160400 300 X 30 MM 72.00 6

Steel wide flats S355J2Acc. to EN 10 025-2Tolerances acc. to EN 10 029


ARTICLE GROUP 162


162110 200 X 10 MM 16.00 6162115 200 X 15 MM 24.00 6162210 250 X 10 MM 20.00 6162315 300 X 15 MM 36.00 6


19/54

STEEL

www.norskstaal.no18

L-profile NVD 36Tolreances acc. to DIN 1022



Chargenumber stamped in the material on both ends

ARTICLE GROUP 14


14010 200 X 90 X 9,0 X 12 MM 22.44

14020 250 X 90 X 9,0 X 13 MM 26.7214023 250 X 90 X 10,5 X 15 MM 30.9114025 250 X 90 X 11,5 X 16 MM 33.25

14030 300 X 100 X 10,5 X 15 MM 36.3114035 300 X 100 X 11,5 X 16 MM 39.27

Steel bulb flats (HP) NVATolerances acc. to EN 10 067

Length tolerances -0/+100 mmInspection certificate acc. to EN 10 204-3.2-DNV

ARTICLE GROUP 4


4200 80 X 6,0 MM 4.95 64210 100 X 6,0 MM 6.20 64220 120 X 6,0 MM 7.42 6

4226 80 X 7,0 MM 5.60 64230 100 X 7,0 MM 7.00 64240 120 X 7,0 MM 8.42 64250 140 X 7,0 MM 9.93 64260 160 X 7,0 MM 11.63 6


4350 140 X 9,0 MM 12.14 64360 160 X 9,0 MM 14.28 64390 180 X 9,0 MM 16.52 124400 200 X 9,0 MM 18.87 12


4485 260 X 11,0 MM 30.91 124490 280 X 11,0 MM 34.17 12

4500 300 X 11,0 MM 37.36 12

4510 200 X 11,5 MM 22.80 12

4521 220 X 12,0 MM 26.72 124530 240 X 12,0 MM 29.86 12

4540 260 X 12,0 MM 33.05 124550 280 X 12,0 MM 36.41 124560 300 X 12,0 MM 39.00 12

4570 320 X 12,0 MM 43.35 124580 340 X 12.0 MM 47.02 12

4600 370 X 13,0 MM 55.70 12

4610 340 X 14,0 MM 52.55 124615 400 X 14,0 MM 65.18 12

Steel bulb flats (HP) NVD 36Tolerances acc. to EN 10 067



ARTICLE GROUP 13


13120 120 X 8,0 MM 9.35 1213140 140 X 8,0 MM 11.01 1213160 160 X 8,0 MM 12.95 1213180 180 X 8,0 MM 15.10 12

13190 180 X 10,0 MM 17.95 12

13192 140 X 9,0 MM 12.14 613194 160 X 9,0 MM 14.28 6

13196 180 X 9,0 MM 16.52 1213198 200 X 9,0 MM 18.87 12

13200 200 X 10,0 MM 20.50 1213220 220 X 10,0 MM 23.26 1213240 240 X 10,0 MM 25.91 1213260 260 X 10,0 MM 28.87 12

13300 300 X 11,0 MM 37.36 12

13301 200 X 11,5 MM 22.80 1213302 220 X 11,5 MM 25.89 12

13303 240 X 12,0 MM 29.86 12

13306 260 X 12,0 MM 33.05 1213310 300 X 12,0 MM 39.78 1213320 320 X 12,0 MM 43.35 12



20/54

STEEL


Steel equal angles S235JRAcc. to EN 10 025-2

Dimensions acc. to EN 10 056-1

Tolerances acc. to EN 10 056-2



ARTICLE GROUP 21


21024 20 X 20 X 3 MM 0.90 621032 25 X 25 X 3 MM 1.14 6

21040 25 X 25 X 4 MM 1.48 6

21056 30 X 30 X 3 MM 1.39 621064 30 X 30 X 4 MM 1.82 6

21068 30 X 30 X 5 MM 2.22 6

21072 35 X 35 X 4 MM 2.14 621080 40 X 40 X 4 MM 2.47 6

21085 40 X 40 X 5 MM 3.03 621095 45 X 45 X 5 MM 3.45 621097 50 X 50 X 5 MM 3.85 6

21099 50 X 50 X 6 MM 4.56 621108 55 X 55 X 6 MM 5.05 6

21109 50 X 50 X 8 MM 5.94 6

21110 60 X 60 X 6 MM 5.53 621123 60 X 60 X 6 MM 5.53 12

21134 60 X 60 X 8 MM 7.23 6

21143 65 X 65 X 7 MM 6.97 1221155 70 X 70 X 7 MM 7.53 621158 70 X 70 X 7 MM 7.53 12

21176 75 X 75 X 8 MM 9.21 1221190 80 X 80 X 8 MM 9.85 621197 80 X 80 X 8 MM 9.85 12

21232 100 X 100 X 10 MM 15.40 6

21239 100 X 100 X 10 MM 15.40 12

21263 120 X 120 X 12 MM 22.05 12

21277 140 X 140 X 13 MM 28.10 12

21289 150 X 150 X 12 MM 27.95 12

21291 150 X 150 X 15 MM 34.48 12

21295 200 X 200 X 16 MM 49.50 12

Steel unequal angles S235JRAcc. to EN 10 025-2



Length tolerances +/-100 mmInspection certificate acc. to EN 10 204-3.1

ARTICLE GROUP 22


22025 40 X 20 X 4 MM 1.81 622033 45 X 30 X 4 MM 2.30 6

22034 45 X 30 X 5 MM 2.83 622035 50 X 40 X 5 MM 3.42 622036 60 X 30 X 5 MM 3.44 622043 60 X 40 X 5 MM 3.84 6

22050 60 X 40 X 6 MM 4.55 6

22057 65 X 50 X 5 MM 4.44 6

22060 65 X 50 X 7 MM 6.09 622063 65 X 50 X 7 MM 6.09 12

22069 75 X 50 X 6 MM 5.70 1222073 75 X 50 X 7 MM 6.64 1222079 75 X 50 X 8 MM 7.52 12

22092 80 X 40 X 6 MM 5.52 6

22114 100 X 50 X 6 MM 6.99 1222115 100 X 50 X 8 MM 9.17 12

22128 100 X 65 X 7 MM 8.95 1222129 100 X 65 X 8 MM 10.16 12

22137 100 X 75 X 8 MM 10.80 1222139 100 X 75 X 9 MM 12.00 12

22151 120 X 80 X 8 MM 12.40 1222155 120 X 80 X 10 MM 15.30 12

22167 130 X 65 X 8 MM 12.10 12

22169 130 X 65 X 10 MM 14.90 12

22187 150 X 75 X 9 MM 15.60 1222188 150 X 75 X 10 MM 17.44 12

22196 150 X 100 X 10 MM 19.40 1222197 150 X 100 X 12 MM 23.10 12

22218 160 X 80 X 12 MM 22.00 12

22242 200 X 100 X 10 MM 23.50 1222244 200 X 100 X 12 MM 27.80 12


21/54

STEEL

www.norskstaal.no20

Steel equal angles NVADimensions acc. to EN 10 056-1




ARTICLE GROUP 15


15092 50 X 50 X 5 MM 3.85 615099 50 X 50 X 6 MM 4.56 615109 50 X 50 X 8 MM 5.94 6


15141 65 X 65 X 7 MM 6.97 615152 65 X 65 X 9 MM 8.79 6

15155 70 X 70 X 7 MM 7.53 615158 70 X 70 X 7 MM 7.53 1215165 70 X 70 X 9 MM 9.53 12


15190 80 X 80 X 8 MM 9.85 615197 80 X 80 X 8 MM 9.85 1215207 80 X 80 X 10 MM 12.10 12

15218 90 X 90 X 9 MM 12.40 12

15232 100 X 100 X 10 MM 15.40 615239 100 X 100 X 10 MM 15.40 1215246 100 X 100 X 12 MM 18.20 12

15253 110 X 110 X 10 MM 16.90 12

15260 120 X 120 X 11 MM 20.30 1215263 120 X 120 X 12 MM 22.05 12

15274 130 X 130 X 12 MM 24.10 12


15295 200 X 200 X 16 MM 49.50 12

Steel unequal angles NVADimensions acc. to EN 10 056-1




ARTICLE GROUP 16


16057 65 X 50 X 5 MM 4.44 616058 65 X 50 X 6 MM 5.26 1216063 65 X 50 X 7 MM 6.09 12

16067 75 X 50 X 6 MM 5.70 616069 75 X 50 X 6 MM 5.70 1216071 75 X 50 X 7 MM 6.64 616073 75 X 50 X 7 MM 6.64 1216077 75 X 50 X 8 MM 7.52 616079 75 X 50 X 8 MM 7.52 12

16092 80 X 40 X 6 MM 5.52 616103 80 X 40 X 8 MM 7.21 12

16113 100 X 50 X 6 MM 6.99 616114 100 X 50 X 6 MM 6.99 1216115 100 X 50 X 8 MM 9.17 1216118 100 X 50 X 8 MM 9.17 616127 100 X 50 X 10 MM 11.30 12

16128 100 X 65 X 7 MM 8.95 12

16129 100 X 65 X 8 MM 10.16 1216130 100 X 65 X 9 MM 11.30 1216131 100 X 65 X 10 MM 12.48 12

16137 100 X 75 X 8 MM 10.80 1216139 100 X 75 X 9 MM 12.00 1216140 100 X 75 X 10 MM 13.36 12

16151 120 X 80 X 8 MM 12.40 1216155 120 X 80 X 10 MM 15.30 1216163 120 X 80 X 12 MM 18.20 12

16167 130 X 65 X 8 MM 12.10 1216169 130 X 65 X 10 MM 14.90 12

16171 130 X 65 X 12 MM 17.75 12

16187 150 X 75 X 9 MM 15.60 1216188 150 X 75 X 10 MM 17.44 1216190 150 X 75 X 12 MM 20.45 12

16192 150 X 90 X 10 MM 18.56 1216194 150 X 90 X 12 MM 22.00 12

16196 150 X 100 X 10 MM 19.40 1216197 150 X 100 X 12 MM 23.10 12

16242 200 X 100 X 10 MM 23.50 1216244 200 X 100 X 12 MM 27.80 12

16245 200 X 100 X 14 MM 32.23 12


22/54

STEEL


Steel equal angles S355J2Acc. to EN 10 025-2




Chargenumber stamped on both ends for profiles

with weigth from 15 kg/m

ARTICLE GROUP 186


186045 40 X 40 X 5 MM 3.03 6


186059 60 X 60 X 6 MM 5.53 6186060 60 X 60 X 6 MM 5.53 12186063 60 X 60 X 8 MM 7.23 12

186067 70 X 70 X 7 MM 7.53 6186068 70 X 70 X 7 MM 7.53 12186070 70 X 70 X 9 MM 9.53 12

186072 75 X 75 X 8 MM 9.21 6186073 75 X 75 X 8 MM 9.21 12186075 75 X 75 X 10 MM 11.30 12

186079 80 X 80 X 8 MM 9.85 6186080 80 X 80 X 8 MM 9.85 12186082 80 X 80 X 10 MM 12.10 12

186090 90 X 90 X 9 MM 12.40 12

186099 100 X 100 X 10 MM 15.40 6186100 100 X 100 X 10 MM 15.40 12186110 100 X 100 X 12 MM 18.20 12

186120 120 X 120 X 12 MM 22.05 12

186150 150 X 150 X 14 MM 32.20 12

186180 180 X 180 X 18 MM 48.60 12

186200 200 X 200 X 16 MM 49.50 12

Steel unequal angles S355J2Acc. to EN 10 025-2




Chargenumber stamped on both ends for profiles

with weigth from 15 kg/m

ARTICLE GROUP 187


187030 75 X 50 X 7 MM 6.64 12


187128 120 X 80 X 10 MM 15.30 12

187130 130 X 65 X 10 MM 14.90 12


187139 180 X 90 X 10 MM 20.96 12187140 180 X 90 X 12 MM 24.88 12

187142 200 X 100 X 10 MM 23.50 12187150 200 X 100 X 12 MM 27.80 12

Steel tees S235JRAcc. to EN 10 025-2




ARTICLE GROUP 24


24022 30 X 30 X 4 MM 1.81 6

24036 40 X 40 X 5 MM 3.02 6

24050 50 X 50 X 6 MM 4.53 6

24060 60 X 60 X 7 MM 6.35 12

24064 70 X 70 X 8 MM 8.49 12

24074 80 X 80 X 9 MM 10.90 12

24085 100 X 100 X 11 MM 16.70 12

24092 120 X 120 X 13 MM 23.70 12

24099 140 X 140 X 15 MM 31.90 12


23/54

STEEL

www.norskstaal.no22

43242 UNP 240 33.90 12 406.8043262 UNP 260 38.70 12 464.4043282 UNP 280 42.60 12 511.20

43302 UNP 300 47.10 12 565.2043322 UNP 320 61.00 12 732.0043352 UNP 350 62.40 12 748.80

43402 UNP 400 73.20 12 878.40

Steel channels UNP S235JRAcc. to EN 10 025-2

Tolerances acc. to DIN 1026/ NS-EN 10 279



ARTICLE GROUP 40

Article no. Profile no. Kg/m Lengths (m) Kg/Length

40040 NR 40 (40X35) 4.97 6 29.80

40050 NR 50 (50X38) 5.70 6 34.20

40060 NR 60 (60X30) 5.17 6 31.00

40065 NR 65 (65X42) 7.20 6 43.20

Steel channels UNP S235JRAcc. to EN 10 025-2

Tolerances acc. to DIN 1026/NS-EN 10 279Length tolerances -0/+100 mm


ARTICLE GROUP 41


41080 UNP 80 8.81 6 52.9041082 UNP 80 8.81 12 105.70

41100 UNP 100 10.80 6 64.8041102 UNP 100 10.80 12 129.60

41120 UNP 120 13.70 6 82.2041122 UNP 120 13.70 12 164.40

41142 UNP 140 16.30 12 195.60

Steel channels UNP S355J2Acc. to EN 10 025-2Tolerances acc. to DIN 1026/NS-EN 10 279Length tolerances -0/+100 mm


ARTICLE GROUP 43


43082 UNP 80 8.81 12 105.70

43102 UNP 100 10.80 12 129.60

43122 UNP 120 13.70 12 164.4043142 UNP 140 16.30 12 195.6043162 UNP 160 19.20 12 230.4043182 UNP 180 22.40 12 268.80

43202 UNP 200 25.80 12 309.6043222 UNP 220 30.00 12 360.00

UNP

Measurements in mm Surface Desig- Sectional

nation areah b s t cm2 m2/m

30 30 33 5 7 5,44 0,17440 40 35 5 7 6,21 0,19950 50 38 5 7 7,12 0,23260 60 30 6 6 6,46 0,21565 65 42 5,5 7,5 9,03 0,273

80 80 45 6 8 11,0 0,312100 100 50 6 8,5 13,5 0,372120 120 55 7 9 17,0 0,434140 140 60 7 10 20,4 0,489160 160 65 7,5 10,5 24,0 0,546

180 180 70 8 11 28,0 0,611200 200 75 8,5 11,5 32,2 0,661220 220 80 9 12,5 37,4 0,718

240 240 85 9,5 13 42,3 0,775260 260 90 10 14 48,3 0,834

280 280 95 10 15 53,3 0,890300 300 100 10 16 58,8 0,950320 320 100 14 17,5 75,8 0,982350 350 100 14 16 77,3 1,05400 400 110 14 18 91,5 1,182



24/54

STEEL


Steel channels UNP S355G11 + N/MNORSOK M-120 Rev. 5, MDS Y-26, rev. 5

and acc. to EN 10225


Length tolerances -0/+100 mmChargenumber stamped on both ends


ARTICLE GROUP 176


176100 UNP 100 10.80 12 129.60176120 UNP 120 13.70 12 164.40176140 UNP 140 16.30 12 195.60176160 UNP 160 19.20 12 230.40176180 UNP 180 22.40 12 268.80

176200 UNP 200 25.80 12 309.60176220 UNP 220 30.00 12 360.00176240 UNP 240 33.90 12 406.80176260 UNP 260 38.70 12 464.40176280 UNP 280 42.60 12 511.20

176300 UNP 300 47.10 12 565.20176350 UNP 350 61.80 12 741.60

176400 UNP 400 73.20 12 878.40

Steel channels UPE S355NAcc. to EN 10 025-3

Tolerances acc. to DIN 1026/ NS-EN 10 279

Guaranteed Si 0.15-0.25%

Length tolerances -0/+100 mmInspection certificate acc. to EN 10 204-3.1

ARTICLE GROUP 39


39092 UPE 80 8.10 12 97.20

39112 UPE 100 10.00 12 120.0039132 UPE 120 12.40 12 148.8039152 UPE 140 14.80 12 177.6039172 UPE 160 17.30 12 207.6039192 UPE 180 20.10 12 241.20

39212 UPE 200 23.30 12 279.6039215 UPE 200 23.30 15 349.5039232 UPE 220 27.10 12 325.2039235 UPE 220 27.10 15 406.5039252 UPE 240 30.80 12 369.6039255 UPE 240 30.80 15 462.0039282 UPE 270 35.90 12 430.8039285 UPE 270 35.90 15 538.50

39302 UPE 300 45.30 12 543.6039305 UPE 300 45.30 15 679.50

39332 UPE 330 54.40 12 652.8039362 UPE 360 62.40 12 748.80

39402 UPE 400 73.80 12 885.60

UPE Axis

Measurements in mm Surface Desig- Sectional y - y z - z

nation area Iy

Wy

iy

Iz

Wz

iz

h b s t cm2 m2/m mm4 mm3 mm mm4 mm3 mmUPE x106 x103 x106 x103

80 80 50 4,0 7,0 1010 0,343 1,07 26,8 32,6 0,25 8,0 15,9

100 100 55 4,5 7,5 1250 0,402 2,07 41,4 40,7 0,38 10,6 17,5

120 120 60 5,0 8,0 1540 0,460 3,64 60,6 48,6 0,55 13,8 19,0

140 140 65 5,0 9,0 1840 0,520 5,99 85,6 57,1 0,79 18,2 20,7

160 160 70 5,5 9,5 2170 0,579 9,11 114,0 64,8 1,07 22,6 22,2

180 180 75 5,5 10,5 2510 0,639 13,53 150,0 73,4 1,44 28,6 23,9

200 200 80 6,0 11,0 2900 0,697 19,09 191,0 81,1 1,87 34,4 25,4

220 220 85 6,5 12,0 3390 0,756 26,82 244,0 89,0 2,47 42,5 27,0

240 240 90 7,0 12,5 3850 0,813 35,99 300,0 96,7 3,11 50,1 28,4

270 270 95 7,5 13,5 4480 0,892 52,55 389,0 108,0 4,01 60,7 29,9

300 300 100 9,5 15,0 5660 0,968 78,23 522,0 118,0 5,38 75,6 30,8

330 330 105 11,0 16,0 6780 1,043 110,08 667,0 127,0 6,81 89,7 31,7

360 360 110 12,0 17,0 7790 1,121 148,25 824,0 138,0 8,43 105,0 32,9

400 400 115 13,5 18,0 9190 1,218 209,81 1049,0 151,0 10,40 123,0 33,7


25/54

STEEL

www.norskstaal.no24

Steel sections IPE S355J2Acc. to EN 10 025-2



Inspection certifcate acc. to EN 10 204-3.1

ARTICLE GROUP 49


49082 IPE 80 6.12 12 73.40

49102 IPE 100 8.26 12 99.1049122 IPE 120 10.60 12 127.2049142 IPE 140 13.20 12 158.4049145 IPE 140 13.20 15 198.0049162 IPE 160 16.10 12 193.2049165 IPE 160 16.10 15 241.5049182 IPE 180 19.20 12 230.4049185 IPE 180 19.20 15 288.00

49202 IPE 200 22.90 12 274.8049205 IPE 200 22.90 15 343.5049222 IPE 220 26.70 12 320.4049225 IPE 220 26.70 15 400.5049242 IPE 240 31.30 12 375.6049245 IPE 240 31.30 15 469.5049272 IPE 270 36.80 12 441.6049275 IPE 270 36.80 15 552.0049276 IPE 270 36.80 20 736.00

49302 IPE 300 43.00 12 516.0049305 IPE 300 43.00 15 645.0049306 IPE 300 43.00 20 860.0049332 IPE 330 50.10 12 601.2049335 IPE 330 50.10 15 751.5049336 IPE 330 50.10 20 1002.0049362 IPE 360 58.20 12 698.4049365 IPE 360 58.20 15 873.0049366 IPE 360 58.20 20 1164.00

49402 IPE 400 67.60 12 811.2049405 IPE 400 67.60 15 1014.0049406 IPE 400 67.60 20 1352.00

49452 IPE 450 79.20 12 950.4049456 IPE 450 79.20 20 1584.00

49502 IPE 500 92.50 12 1110.0049505 IPE 500 92.50 15 1387.5049506 IPE 500 92.50 20 1850.0049552 IPE 550 108.10 12 1297.2049556 IPE 550 108.10 20 2162.00

49602 IPE 600 124.40 12 1492.8049606 IPE 600 124.40 20 2488.00

Measurements in mm Surface

Desig- Sectional


80 80 46 3,8 5,2 7,64 0,328100 100 55 4,1 5,7 10,3 0,400120 120 64 4,4 6,3 13,2 0,475140 140 73 4,7 6,9 16,4 0,551160 160 82 5,0 7,4 20,1 0,623

180 180 91 5,3 8,0 23,9 0,698200 200 100 5,6 8,5 28,5 0,768220 220 110 5,9 9,2 33,4 0,848240 240 120 6,2 9,8 39,1 0,922270 270 135 6,6 10,2 45,9 1,04

300 300 150 7,1 10,7 53,8 1,16330 330 160 7,5 11,5 62,6 1,25

360 360 170 8,0 12,7 72,7 1,35400 400 180 8,6 13,5 84,5 1,47

450 450 190 9,4 14,6 98,8 1,61500 500 200 10,2 16,0 116 1,74550 550 210 11,1 17,2 134 1,88600 600 220 12,0 19,0 156 2,01

IPE

Steel sections IPE S355G11 + N/MNORSOK M-120 Rev. 5, MDS Y-26, rev. 5





ARTICLE GROUP 177


177100 IPE 100 8.26 12 99.10177120 IPE 120 10.60 12 127.20177140 IPE 140 13.20 12 158.40177160 IPE 160 16.10 12 193.20177180 IPE 180 19.20 12 230.40

177200 IPE 200 22.80 12 273.60177220 IPE 220 26.70 12 320.40177240 IPE 240 31.30 12 375.60177270 IPE 270 36.80 12 441.60

177300 IPE 300 43.00 12 516.00177330 IPE 330 50.10 12 601.20177360 IPE 360 58.20 12 698.40

177400 IPE 400 67.60 12 811.20177450 IPE 450 79.20 12 950.40

177500 IPE 500 92.50 12 1110.00

177600 IPE 600 124.40 12 1492.80


26/54

STEEL


Steel beams HEA S355J2Acc. to EN 10 025-2




ARTICLE GROUP 48


48102 HEA 100 17.00 12 204.0048105 HEA 100 17.00 15 255.0048122 HEA 120 20.30 12 243.6048142 HEA 140 25.20 12 302.4048145 HEA 140 25.20 15 378.0048162 HEA 160 31.00 12 372.0048165 HEA 160 31.00 15 465.0048182 HEA 180 36.20 12 434.4048185 HEA 180 36.20 15 543.00

48202 HEA 200 43.10 12 517.2048205 HEA 200 43.10 15 646.5048206 HEA 200 43.10 20 862.0048222 HEA 220 51.50 12 618.0048225 HEA 220 51.50 15 772.5048226 HEA 220 51.50 20 1030.0048242 HEA 240 61.50 12 738.0048245 HEA 240 61.50 15 922.50

48246 HEA 240 61.50 20 1230.0048262 HEA 260 69.60 12 835.2048265 HEA 260 69.60 15 1044.0048266 HEA 260 69.60 20 1392.0048282 HEA 280 77.90 12 934.8048285 HEA 280 77.90 15 1168.5048286 HEA 280 77.90 20 1558.00

48302 HEA 300 90.10 12 1081.2048305 HEA 300 90.10 15 1351.5048306 HEA 300 90.10 20 1802.0048322 HEA 320 99.60 12 1195.2048325 HEA 320 99.60 15 1494.0048326 HEA 320 99.60 20 1992.00

48342 HEA 340 107.10 12 1285.2048346 HEA 340 107.10 20 2142.0048362 HEA 360 114.20 12 1370.4048365 HEA 360 114.20 15 1713.0048366 HEA 360 114.20 20 2284.00


48502 HEA 500 158.10 12 1897.2048506 HEA 500 158.10 20 3162.00

48602 HEA 600 181.60 12 2179.2048606 HEA 600 181.60 20 3632.00

Steel beams HEA S355G11 + N/MNORSOK M-120 Rev. 5, MDS Y-26, rev. 5


Toleraces acc. to EN 10 034



ARTICLE GROUP 178




178300 HEA 300 90.10 12 1081.20178360 HEA 360 114.20 12 1370.40

178400 HEA 400 127.50 12 1530.00178450 HEA 450 142.80 12 1713.60

178500 HEA 500 158.10 12 1897.20178600 HEA 600 181.60 12 2179.20178700 HEA 700 209.00 12 2508.00

178800 HEA 800 228.50 12 2742.00178920 HEA 1000 277.00 12 3324.00

HEA

Measurements in mm SurfaceDesig- Sectional


100 96 100 5 8 21,2 0,561

120 114 120 5 8 25,3 0,677140 133 140 5,5 8,5 31,4 0,794160 152 160 6,0 9 38,8 0,906180 171 180 6 9,5 45,3 1,02

200 190 200 6,5 10 53,8 1,14220 210 220 7 11 64,3 1,26240 230 240 7,5 12 76,8 1,37260 250 260 7,5 12,5 86,8 1,48280 270 280 8 13 97,3 1,60

300 290 300 8,5 14 112 1,72320 310 300 9 15,5 124 1,76340 330 300 9,5 16,5 133 1,79360 350 300 10 17,5 143 1,83400 390 300 11 19,0 159 1,91

450 440 300 11,5 21,0 178 2,01500 490 300 12 23,0 198 2,11

550 540 300 12,5 24,0 212 2,21600 590 300 13 25,0 226 2,31650 640 300 13,5 26,0 242 2,41

700 690 300 14,5 27,0 260 2,50800 790 300 15 28,0 286 2,70900 890 300 16 30,0 320 2,90

1000 990 300 16,5 31,0 347 3,10


27/54

STEEL

www.norskstaal.no26

Steel beams HEB S355G11 + N/MNORSOK M-120 Rev.5, MDS Y-26, rev. 5

and acc. to NS-EN 10 225

Tolerances acc. to NS-EN 10 034



ARTICLE GROUP 180


180100 HEB 100 20.80 12 249.60180120 HEB 120 27.20 12 326.40180140 HEB 140 34.40 12 412.80180160 HEB 160 43.50 12 522.00180180 HEB 180 52.20 12 626.40

180200 HEB 200 62.50 12 750.00

180220 HEB 220 72.90 12 874.80180240 HEB 240 84.90 12 1018.80180260 HEB 260 94.90 12 1138.80180280 HEB 280 105.10 12 1261.20

180300 HEB 300 119.30 12 1431.60180320 HEB 320 129.50 12 1554.00180340 HEB 340 136.70 12 1640.40180360 HEB 360 144.80 12 1737.60

180400 HEB 400 158.10 12 1897.20180450 HEB 450 174.40 12 2092.80

180500 HEB 500 190.70 12 2288.40180550 HEB 550 203.00 12 2436.00

180600 HEB 600 216.20 12 2594.40180650 HEB 650 229.50 12 2754.00

180700 HEB 700 245.80 12 2949.60

180800 HEB 800 267.20 12 3206.40

180920 HEB 1000 320.30 12 3843.60

Steel beams HEB S355J2Acc. to EN 10 025-2




ARTICLE GROUP 45


45102 HEB 100 20.80 12 249.6045122 HEB 120 27.20 12 326.4045125 HEB 120 27.20 15 408.0045142 HEB 140 34.40 12 412.8045145 HEB 140 34.40 15 516.0045162 HEB 160 43.50 12 522.0045165 HEB 160 43.50 15 652.5045182 HEB 180 52.20 12 626.4045185 HEB 180 52.20 15 783.0045186 HEB 180 52.20 20 1044.00

45202 HEB 200 62.50 12 750.0045205 HEB 200 62.50 15 937.5045206 HEB 200 62.50 20 1250.0045222 HEB 220 72.90 12 874.8045225 HEB 220 72.90 15 1093.5045226 HEB 220 72.90 20 1458.0045242 HEB 240 84.90 12 1018.8045245 HEB 240 84.90 15 1273.5045246 HEB 240 84.90 20 1698.00

45262 HEB 260 94.90 12 1138.8045265 HEB 260 94.90 15 1423.5045266 HEB 260 94.90 20 1898.0045282 HEB 280 105.10 12 1261.2045285 HEB 280 105.10 15 1576.5045286 HEB 280 105.10 20 2102.00

45302 HEB 300 119.30 12 1431.6045305 HEB 300 119.30 15 1789.5045306 HEB 300 119.30 20 2386.0045322 HEB 320 129.50 12 1554.0045325 HEB 320 129.50 15 1942.5045326 HEB 320 129.50 20 2590.0045342 HEB 340 136.70 12 1640.40

45345 HEB 340 136.70 15 2050.5045346 HEB 340 136.70 20 2734.0045362 HEB 360 144.80 12 1737.6045365 HEB 360 144.80 15 2172.0045366 HEB 360 144.80 20 2896.00

45402 HEB 400 158.10 12 1897.2045405 HEB 400 158.10 15 2371.5045406 HEB 400 158.10 20 3162.0045452 HEB 450 174.40 12 2092.8045455 HEB 450 174.40 15 2616.0045456 HEB 450 174.40 20 3488.00

45502 HEB 500 190.70 12 2288.40

45505 HEB 500 190.70 15 2860.5045506 HEB 500 190.70 20 3814.00

45602 HEB 600 216.20 12 2594.4045606 HEB 600 216.20 20 4324.00

Measurements in mm Surface

Desig- Sectionalnation area

h b s t cm2 m2/m

100 100 100 6,0 10,0 26,0 0,567120 120 120 6,5 11,0 34,0 0,686140 140 140 7,0 12,0 43,0 0,805160 160 160 8,0 13,0 54,3 0,918180 180 180 8,5 14,0 65,3 1,04

200 200 200 9,0 15,0 78,1 1,15220 220 220 9,5 16,0 91,0 1,27240 240 240 10,0 17,0 106 1,38260 260 260 10,0 17,5 118 1,50280 280 280 10,5 18,0 131 1,62

300 300 300 11,0 19,0 149 1,73320 320 300 11,5 20,5 161 1,77340 340 300 12,0 21,5 171 1,81360 360 300 12,5 22,5 181 1,85

400 400 300 13,5 24,0 198 1,93450 450 300 14,0 26,0 218 2,03

500 500 300 14,5 28,0 239 2,12550 550 300 15,0 29,0 254 2,22600 600 300 15,5 30,0 270 2,32

650 650 300 16,0 31,0 286 2,42700 700 300 17,0 32,0 306 2,52800 800 300 17,5 33,0 334 2,71900 900 300 18,5 35,0 371 2,91

1000 1000 300 19,0 36,0 400 3,11

HEB


28/54

STEEL


Cold formed welded circularhollow sections Hybox S355J2H

Acc. to EN 10 219-1

Tolerances acc. to EN 10 219-2Inspection certificate EN 10 204-3.1

ARTICLE GROUP 218

Article no. Dimension Kg/m

Lengths (m)

218032 88,9 X 5,0 MM 10.30 12

218092 114,3 X 6,0 MM 16.03 12

218132 139,7 X 5,0 MM 16.60 12218142 139,7 X 6,0 MM 19.78 12218152 139,7 X 8,0 MM 25.98 12

218282 168,3 X 6,0 MM 24.02 12218292 168,3 X 8,0 MM 31.63 12218302 168,3 X 10,0 MM 39.04 12

218332 193,7 X 6,0 MM 27.80 12218342 193,7 X 8,0 MM 36.60 12218352 193,7 X 10,0 MM 45.30 12

218382 219,1 X 6,0 MM 31.53 12218392 219,1 X 8,0 MM 41.65 12218402 219,1 X 10,0 MM 51.57 12218412 219,1 X 12,5 MM 63.69 12

218442 244,5 X 8,0 MM 46.70 12

218472 273,0 X 6,0 MM 39.50 12218482 273,0 X 8,0 MM 52.28 12218492 273,0 X 10,0 MM 64.86 12

218542 323,9 X 8,0 MM 62.32 12218552 323,9 X 10,0 MM 77.41 12218562 323,9 X 12,5 MM 95.99 12

218612 355,6 X 6,0 MM 51.70 12

Cold formed hollow sectionsHybox S355J2H

Acc. to EN 10 219-1

UnoiledImpact tested at -20 gr.C

Tolerances acc. to EN 10 219-2Length tolerances -0/+50 mm


ARTICLE GROUP 233


233300 30 X 30 X 3,00 MM 2.43 6

233310 40 X 40 X 3,00 MM 3.38 6

233320 40 X 40 X 4,00 MM 4.30 6

233330 50 X 50 X 3,00 MM 4.35 6233340 50 X 50 X 4,00 MM 5.58 6233342 50 X 50 X 4,00 MM 5.58 12233350 50 X 50 X 5,00 MM 6.54 6233352 50 X 50 X 5,00 MM 6.54 12

233360 60 X 60 X 3,00 MM 5.32 6233362 60 X 60 X 3,00 MM 5.32 12233370 60 X 60 X 4,00 MM 6.87 6233372 60 X 60 X 4,00 MM 6.87 12233380 60 X 60 X 5,00 MM 8.15 6233382 60 X 60 X 5,00 MM 8.15 12



233460 80 X 80 X 6,00 MM 13.46 10233462 80 X 80 X 6,00 MM 13.46 12233762 80 X 80 X 8,00 MM 16.69 12

233470 90 X 90 X 4,00 MM 10.76 6233472 90 X 90 X 4,00 MM 10.76 12233482 90 X 90 X 5,00 MM 13.00 12


233540 100 X 100 X 8,00 MM 21.92 10233542 100 X 100 X 8,00 MM 21.92 12233782 100 X 100 X 10,00 MM 26.11 12

233792 120 X 120 X 4,00 MM 14.48 12233802 120 X 120 X 6,00 MM 21.11 12


29/54

STEEL

www.norskstaal.no28

233552 120 X 120 X 5,00 MM 17.82 12233572 120 X 120 X 8,00 MM 27.04 12233582 120 X 120 X 10,00 MM 31.84 12

233592 140 X 140 X 5,00 MM 20.69 12233812 140 X 140 X 6,00 MM 24.52 12233822 140 X 140 X 8,00 MM 31.43 12233832 140 X 140 X 10,00 MM 38.12 12

233602 150 X 150 X 5,00 MM 22.64 12233842 150 X 150 X 6,00 MM 26.93 12233632 150 X 150 X 8,00 MM 34.72 12233642 150 X 150 X 10,00 MM 42.30 12

233843 160 X 160 X 5,00 MM 23.83 12233852 160 X 160 X 6,00 MM 28.29 12233862 160 X 160 X 8,00 MM 36.46 12

233872 160 X 160 X 10,00 MM 44.40 12

233882 180 X 180 X 6,00 MM 32.74 12233892 180 X 180 X 8,00 MM 42.33 12233902 180 X 180 X 10,00 MM 51.71 12


233702 250 X 250 X 8,00 MM 60.53 12233972 250 X 250 X 6,00 MM 46.10 12

233712 250 X 250 X 10,00 MM 74.46 12233982 250 X 250 X 12,00 MM 86.50 12

233722 300 X 300 X 8,00 MM 73.33 12233732 300 X 300 X 10,00 MM 90.54 12

233742 300 X 300 X 12,00 MM 106.10 12

Cold formed hollow sectionsHybox S355J2H

Acc. to EN 10 219-1Unoiled

Impact tested at -20 gr. C



Inspection certificate EN 10 204-3.1

ARTICLE GROUP 236


236320 50 X 30 X 3,00 MM 3.38 6236330 50 X 30 X 4,00 MM 4.30 6

236340 60 X 40 X 3,00 MM 4.35 6236350 60 X 40 X 4,00 MM 5.58 6236352 60 X 40 X 4,00 MM 5.58 12

236360 70 X 40 X 3,00 MM 4.73 6

236380 80 X 40 X 3,00 MM 5.32 6236390 80 X 40 X 4,00 MM 6.87 6


236450 90 X 50 X 4,00 MM 8.16 6


236490 100 X 50 X 5,00 MM 10.76 6236492 100 X 50 X 5,00 MM 10.76 12236502 100 X 50 X 6,00 MM 12.55 12236512 100 X 60 X 4,00 MM 9.44 12236522 100 X 60 X 5,00 MM 11.37 12236752 100 X 60 X 6,00 MM 13.46 12236532 100 X 80 X 5,00 MM 13.01 12


236760 120 X 80 X 8,00 MM 23.40 10236762 120 X 80 X 8,00 MM 23.40 12

236792 140 X 80 X 5,00 MM 15.98 12236902 140 X 80 X 6,00 MM 18.87 12

236612 150 X 100 X 5,00 MM 18.64 12236622 150 X 100 X 6,00 MM 22.13 12236642 150 X 100 X 8,00 MM 28.37 12

236652 160 X 80 X 5,00 MM 17.81 12236662 160 X 80 X 6,00 MM 21.11 12236672 160 X 80 X 8,00 MM 26.93 12

236722 200 X 100 X 5,00 MM 22.75 12236732 200 X 100 X 6,00 MM 26.93 12236822 200 X 100 X 8,00 MM 34.72 12236832 200 X 100 X 10,00 MM 42.30 12236032 200 X 120 X 6,00 MM 28.87 12236052 200 X 120 X 8,00 MM 37.19 12236072 200 X 120 X 10,00 MM 45.29 12

236102 250 X 150 X 6,00 MM 36.52 12236852 250 X 150 X 8,00 MM 47.63 12236112 250 X 150 X 10,00 MM 58.14 12

236152 300 X 200 X 6,00 MM 46.10 12

236162 300 X 200 X 8,00 MM 60.28 12236172 300 X 200 X 10,00 MM 74.15 12

236202 400 X 200 X 8,00 MM 73.03 12236212 400 X 200 X 10,00 MM 90.17 12236222 400 X 200 X 12,00 MM 106.08 12

Article no. Dimension Kg/m Lengths (m)Article no. Dimension Kg/m Lengths (m)


30/54

STEEL


Hot formed hollow sectionsCelsius S355NH

Acc. to EN 10 210-1

Outside corner radius 0,5 To 2,0 x tC max 0,16, CEV max 0,41

Impact tested for thickness 6 mm and above:min 40 Joule ved -20 gr.C

Length tolerances -0/+150 mm.

Remaining tolerances acc. to EN 10210-2

US testing of welded bead for thicknesses between

12 mm and 16 mm acc. to EN 10246-8 level U3, inside

weld bead removedInspection certificate acc. to EN 10 204-3.1

ARTICLE GROUP 52


52087 40 X 40 X 4,00 MM 4.56 12 54.70

52097 50 X 50 X 3,20 MM 4.75 12 57.0052107 50 X 50 X 4,00 MM 5.83 12 70.0052117 50 X 50 X 5,00 MM 7.11 12 85.30

52127 60 X 60 X 3,20 MM 5.78 12 69.4052137 60 X 60 X 4,00 MM 7.11 12 85.3052147 60 X 60 X 5,00 MM 8.71 12 104.5052151 60 X 60 X 6,30 MM 12.40 12 148.8052157 60 X 60 X 8,00 MM 13.06 12 156.70

52177 70 X 70 X 5,00 MM 10.30 12 123.60

52197 80 X 80 X 3,60 MM 8.76 12 105.1052207 80 X 80 X 5,00 MM 11.90 12 142.8052217 80 X 80 X 6,30 MM 14.70 12 176.4052227 80 X 80 X 8,00 MM 18.20 12 218.4052247 90 X 90 X 5,00 MM 13.60 12 163.2052257 90 X 90 X 6,30 MM 16.70 12 200.40

52267 100 X 100 X 4,00 MM 12.20 12 146.4052277 100 X 100 X 5,00 MM 15.10 12 181.2052287 100 X 100 X 6,30 MM 18.80 12 225.6052297 100 X 100 X 8,00 MM 23.40 12 280.80

52307 100 X 100 X 10,00 MM 28.50 12 342.00



52397 150 X 150 X 5,00 MM 23.20 12 278.4052407 150 X 150 X 6,30 MM 28.90 12 346.80


52467 160 X 160 X 6,30 MM 30.30 12 363.60

52477 160 X 160 X 8,00 MM 37.90 12 454.8052487 160 X 160 X 10,00 MM 46.70 12 560.40



52677 250 X 250 X 6,30 MM 49.10 12 589.2052687 250 X 250 X 8,00 MM 61.70 12 740.40

52697 250 X 250 X 10,00 MM 76.50 12 918.0052707 250 X 250 X 12,50 MM 94.50 12 1134.0052712 250 X 250 X 16,00 MM 119.34 12 1432.10

52717 300 X 300 X 10,00 MM 92.50 12 1110.0052727 300 X 300 X 12,50 MM 114.00 12 1368.0052817 300 X 300 X 16,00 MM 144.84 12 1738.10

52737 350 X 350 X 10,00 MM 108.00 12 1296.0052747 350 X 350 X 12,50 MM 135.00 12 1620.0052827 350 X 350 X 16,00 MM 170.30 12 2043.60

52752 400 X 400 X 10,00 MM 124.50 12 1494.0052777 400 X 400 X 12,50 MM 155.00 12 1860.00

52787 400 X 400 X 16,00 MM 195.80 12 2349.60



31/54

STEEL

www.norskstaal.no30

53857 300 X 100 X 5,00 MM 31.10 12 373.2053727 300 X 200 X 6,30 MM 49.10 12 589.2053737 300 X 200 X 8,00 MM 61.70 12 740.40

53747 300 X 200 X 10,00 MM 76.50 12 918.0053757 300 X 200 X 12,50 MM 94.50 12 1134.0053817 300 X 200 X 16,00 MM 119.30 12 1431.60

53767 400 X 200 X 10,00 MM 92.50 12 1110.0053777 400 X 200 X 12,50 MM 114.00 12 1368.0053827 400 X 200 X 16,00 MM 144.80 12 1737.60

53787 450 X 250 X 10,00 MM 108.00 12 1296.0053797 450 X 250 X 12,50 MM 135.00 12 1620.0053807 450 X 250 X 16,00 MM 169.30 12 2031.60

Centerless rounds/shafts SS2142Tolerances acc. to ISO h8 and DIN 670,

cold drawn and oiled


ARTICLE GROUP 246


246029 20 MM X 2.51 6

246043 25 MM X 3.93 6246050 30 MM X 5.66 6246063 35 MM X 7.70 6

246077 40 MM X 10.10 6246084 45 MM X 12.70 6

246091 50 MM X 15.70 6

246105 60 MM X 22.60 6246112 65 MM X 26.60 6

246119 70 MM X 30.80 6

246133 80 MM X 40.20 6

246147 90 MM X 50.90 6

246153 100 MM X 62.90 6

246167 120 MM X 90.50 6

Hot formed hollow sectionsCelsius S355NH

Acc. to EN 10 210-1

Outside corner radius 0,5 To 2,0 x tC max 0,16, CEV max 0,41

Impact tested for thickness 6 mm and above:min. 40 Joule ved -20 gr.C

Length tolerances -0/+150 mm.

Remaining tolerances acc. to EN 10210-2

US testing of welded bead for thicknesses between

12 mm and 16 mm acc. to EN 10246-8 level U3, inside

weld bead removedInspection certificate acc. to EN 10 204-3.1

ARTICLE GROUP 53

Article no. Dimension Kg/m Lengths (m)Kg/Length

53047 60 X 40 X 4,00 MM 5.83 12 70.00

53077 80 X 40 X 4,00 MM 7.11 12 85.3053087 80 X 40 X 6,30 MM 10.50 12 126.00

53097 90 X 50 X 3,60 MM 7.61 12 91.30

53117 100 X 50 X 3,20 MM 7.32 12 87.8053127 100 X 50 X 4,00 MM 9.04 12 108.5053137 100 X 50 X 5,00 MM 11.10 12 133.2053147 100 X 50 X 6,30 MM 13.70 12 164.4053151 100 X 50 X 8,00 MM 16.90 12 202.8053167 100 X 60 X 5,00 MM 11.90 12 142.8053177 100 X 60 X 6,30 MM 14.70 12 176.40

53207 120 X 60 X 5,00 MM 13.60 12 163.2053217 120 X 60 X 6,30 MM 16.70 12 200.4053227 120 X 80 X 5,00 MM 15.10 12 181.2053237 120 X 80 X 6,30 MM 18.80 12 225.6053247 120 X 80 X 8,00 MM 23.40 12 280.8053257 120 X 80 X 10,00 MM 28.50 12 342.00

53297 150 X 100 X 5,00 MM 19.10 12 229.2053307 150 X 100 X 6,30 MM 23.80 12 285.6053317 150 X 100 X 8,00 MM 29.70 12 356.40

53327 150 X 100 X 10,00 MM 36.40 12 436.80


53407 200 X 100 X 5,00 MM 23.20 12 278.4053417 200 X 100 X 6,30 MM 28.90 12 346.8053427 200 X 100 X 8,00 MM 36.10 12 433.2053437 200 X 100 X 10,00 MM 44.50 12 534.0053447 200 X 100 X 12,50 MM 54.50 12 654.0053451 200 X 100 X 16,00 MM 66.50 12 798.0053467 200 X 120 X 6,30 MM 30.30 12 363.60

53477 200 X 120 X 8,00 MM 38.58 12 463.0053487 200 X 120 X 10,00 MM 46.70 12 560.40

53687 250 X 150

Date post:	03-Jun-2018
Category:	Documents
Upload:	rejestrownikk
View:	219 times
Download:	0 times

Norsk Staal 2009 Engels k 141209

Documents