Date post: | 12-Oct-2015 |
Category: |
Documents |
Upload: | mistermango |
View: | 64 times |
Download: | 0 times |
of 15
FULLER-TRAYLOR TYPE NT HEAVY DUTY PRIMARY GYRATORY CRUSHER
MINERALS TECHNOLOGY GROUP - CRUSHING
FULLER-TRAYLOR TYPE NT PRIMARY GYRATORY CRUSHER LOW RESTRICTION SHELL AND DESIGN FEATURES
MINERALS TECHNOLOGY GROUP - CRUSHING 1
Less Restriction
Vertical Buttress
Contact Oil Seal
Flat Rim
Negative Offset
Vertical Wall
Reduced Impact and Wear
FULLER-TRAYLOR TYPE NT PRIMARY GYRATORY CRUSHER 500 BHN BOTTOM SHELL LINER ARRANGEMENT FFE Minerals custom designs bottom shell liners to suit ore type or other special conditions with the flexibility to combine abrasion resistant steel plate with cast shields.
Simple liner shapes are easier to handle. High hardness materials and smaller shapes translate into less material waste over time (i.e. Replace liners only where needed, not a single large liner with only localized wear. Bottom shell liners are not replaced in sets as with concaves.)
Greater flexibility in spare part sourcing due to widespread availability of AR plate and simple
liner shapes. Simple layout of the Type NT bottom shell allows customization of liner materials to optimize
wear and performance. Cast shields are available in a variety of materials: manganese steel, alloy steel or white iron.
Bottom shell housing includes 2 inspection ports for the eccentric gear and countershaft pinion.
MINERALS TECHNOLOGY GROUP - CRUSHING 2
500 BHN Abrasion Resistant Plate
3 Inspection ports located strategically to view lower mantle and crusher discharge.
Fuller-Traylor Disk Liner Attachment System
Rock Box Rib Design Rock-on-Rock Impact Reduces Wear
ROCK BOX STYLE SPIDER CAP Optional rock box spider cap, low wear and maintenance resulting from rock-on-rock impact.
MINERALS TECHNOLOGY GROUP - CRUSHING 3
Cast Manganese Steel Standard Work Hardens from Impact and Provides Longer Life as Compared to Carbon Steel
ROCK BOX STYLE SPIDER SHIELDS Available as an option. Low wear and maintenance resulting from rock-on-rock impact. Suitable for direct dump only.
MATERIAL RETENTION WALLS
MINERALS TECHNOLOGY GROUP - CRUSHING 4
Extended Spider Shield Side Walls Available for Multiple Point Direct Dump Arrangement to Resist Side Impact.
SPIDER ASSEMBLY
MINERALS TECHNOLOGY GROUP - CRUSHING 5
Tapered Spider Bushing Can Be Removed and Installed Without Removing the Mainshaft
Supernut Style Spider Bolts Standard Allows Rapid Removal and Installation of the Mainshaft
Automatic Grease Lubrication Standard for Spider Bushing
Phosphorous Bronze Spider Bushing Provides Longer Life as Compared to Cast Iron Bushings
ur)
Hydraulic Spider Separation Available to Allow Rapid Removal and Installation of the Mainshaft (1/2 Ho
TOP SHELL SEAL WITH INTEGRALLY CAST SUPPORT RING Low wear and maintenance resulting from rock-on-rock impact. Greater flexibility in spare part sourcing due to widespread availability of AR plate and simple liner shapes.
MINERALS TEC
Flush 500 BHN Top Shell Seal and Rim Liner Plates Typically Covered By Ore and Less Prone To Being Dislodged By Rock BreakerIntegrally Cast Seal Support Ring Available to Provide Positive Barrier HNOLOGY GROUP - CRUSHING 6
to Moisture and Mud, Resulting in Less Housekeeping
MAINSHAFT ASSEMBLY
MINERALS TECHNOLOGY GROUP - CRUSHING 7
t
Cast Iron Dust Seal Ring Provides Longer Life As Compared to Plastic
Split Ring Contact Oil Seal Provides Barrier to Oil Loss Over Dust Bonnet.
Mainshaft Sleeve Standard Provides Additional Protection of the Upper Journal
Two Piece Head Nut Standard Provides Additional Protection of the Mainshaf
Oil flow between main shaft and inner eccentric bushing. Split ring seal redirects oil flow to outer bushing.
ECCENTRIC ASSEMBLY
MINERALS TECHNOLOGY GROUP - CRUSHING 8
Leaded Bronze Inner Eccentric Bushing for peak performance
Large Face Width Spiral Bevel Gear Set Achieves Strength and Durability Ratings by Greater Contact Area Rather than Extreme Surface Hardness. Less Risk of Tooth Failure Due To Shock Loading
FULLER-TRAYLOR COUNTERSHAFT STANDARD FEATURES Lockplate Style Countershaft Nut Low Maintenance Bearings. Countershaft Bearing Resistance Temperature Detectors Continuous Monitoring Of Bearings.
MINERALS TECHNOLOGY GROUP - CRUSHING 9
Item 1: Countershaft Nut Item 2: Countershaft Locknut Item 3: Lockplate Item 4: (2) Hex Head Cap Screws Item 5: (2) Lockwashers Item 6: Bearing RTDs
TRIPLE CLIPPER TACONITE COUNTERSHAFT OIL SEAL STANDARD Positive barrier to oil loss and dust contamination.
MINERALS TECHNOLOGY GROUP - CRUSHING 10
Triple Oil Seal
FULLER-TRAYLOR MPI-300 MANTLE POSITION INDICATOR
Specifications Non-Linearity: 0.05% of Full Scale Resolution: 1.0 FA DC Hysteresis: 0.00001 in. Repeatability: Resolution + Hysteresis
MINERALS TECHNOLOGY GROUP - CRUSHING 11
High Accuracy Mantle Position Sensor Allows Accurate Setting Control, Improved Liner Wear Monitoring and Automated Crusher Operation
LUBRICATION AND HYDRAULIC SYSTEM Standard Features: Fully Independent Lubrication and Hydraulic Systems Eliminates Risk of Cross
Contamination Duplex Cartridge Type Oil Lubrication Filters Can Be Serviced Online. Standby Lubrication Oil Pump Can Be Serviced Online. High Accuracy Resistance Temperature Detectors (RTDs) Allows Accurate Control
and Continuous Trending for Maintenance 304 Stainless Steel Thermowells RTDs Can Be Serviced Online. Indirect Pipe Mounted Coil Type Heaters - Can Be Serviced Online.
MINERALS TECHNOLOGY GROUP - CRUSHING 12
Fuller-Traylor Type NT Primary Gyratory Crusher Capacities in Metric Tons Per Hour
Capacities are based on the following assumed feed distributions: maximum feed to the crusher (F100 ) equals 80% of the feed opening size and 80% of the feed gradation (F80 ) is equal to or less than 50% of the feed opening size. Bulk Density is assumed to be 1.6 metric tons per cubic meter. Capacities are calculated at the maximum eccentric throw for each machine size. Please note that the above capacities are typical, but crushing applications may vary widely with material, feed characteristics, moisture, and work index. FFE Minerals recommends verification of throughput and capacities of Fuller-Traylor Gyratory Crushers for each installation. Specific throughput needs can be met through engineering analysis and modification of crusher geometry.
MINERALS TECHNOLOGY GROUP - CRUSHING 13
FFE MINERALS / FULLER-TRAYLOR GYRATORY CRUSHER CAPACITIES IN MTPH
Crusher Size Feed Opening Pinion RPM Max. kW
(HP) Open Side Setting of Discharge Opening 127 152 178 203 229 255 280 Nominal Size (mm)
Nominal Size (in) 5 6 7 8 9 10 11
1100 x 1750 (43 x 69)
1100mm (43) 600
375 (500) 1780 2170 2730
1300 x 1750 (51 x 69)
1300mm (51) 600
375 (500) 1650 2040 2560
1370 x 1950 (54 x 77)
1370mm (54) 600
450 (600) 1800 2190 2680 3160
1600 x 2000 (63 x 79)
1600mm (63) 600
450 (600) 1750 2130 2600 2920
1525 x 2260 (60 x 89)
1525mm (60) 600
600 (800) 3020 3700 4617 5485
1525 x 2870 (60 x 113)
1525mm (60) 514
750 (1000) 3810 5485 6160 7165 7665 8200
MINERALS TECHNOLOGY GROUP - CRUSHING 14
Fuller-Traylor Type NT Primary Gyratory Product Analysis
Fuller-Traylor Gyratory Crusher - EstimatedProduct Size Distributions by Crusher OSS
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
0 50 100 150 200 250 300
Particle Size (mm)
Perc
ent P
assi
ng (%
)
127152178203229
Estimated Product Size Distribution Curves
byCrusher Open Side
Setting (mm)
Increasing OSS
Open Side Setting (mm)
To use the Product Analysis Chart, determine what particle size is required (X-Axis) and intersect the appropriate curve based on Open Side Setting (OSS). Correlate the intersecting point on the OSS curve to the Percent Passing (Y-Axis) to determine the approximate percent passing of an exact particle size at an exact Open Side Setting. EXAMPLE: For a Particle Size of 150mm, what is the percent passing a 178mm OSS? The Percentage of 150mm particles passing an OSS of 178mm would be ~76%. Please note, these are typical product size distributions and vary widely with feed distribution and specific rock characteristics materials. For specific application information, please contact FFE Minerals Applications Engineers.
FULLER-TRAYLOR TYPE NTHEAVY DUTY PRIMARY GYRATORY CRUSHERFULLER-TRAYLOR TYPE NT PRIMARY GYRATORY CRUSHERLOW RESTRICTION SHELL AND DESIGN FEATURESFULLER-TRAYLOR TYPE NT PRIMARY GYRATORY CRUSHER500 BHN BOTTOM SHELL LINER ARRANGEMENTFFE Minerals custom designs bottom shell liners to suit ore type or other special conditions with the flexibility to combine abrasion resistant steel plate with cast shields.Simple liner shapes are easier to handle. High hardness materials and smaller shapes translate into less material waste over time (i.e. Replace liners only where needed, not a single large liner with only localized wear. Bottom shell liners are not repGreater flexibility in spare part sourcing due to widespread availability of AR plate and simple liner shapes.Simple layout of the Type NT bottom shell allows customization of liner materials to optimize wear and performance. Cast shields are available in a variety of materials: manganese steel, alloy steel or white iron.Bottom shell housing includes 2 inspection ports for the eccentric gear and countershaft pinion.ROCK BOX STYLE SPIDER CAPROCK BOX STYLE SPIDER SHIELDSAvailable as an option. Low wear and maintenance resulting from rock-on-rock impact. Suitable for direct dump only.SPIDER ASSEMBLYTOP SHELL SEAL WITH INTEGRALLY CAST SUPPORT RINGLow wear and maintenance resulting from rock-on-rock impact. Greater flexibility in spare part sourcing due to widespread availability of AR plate and simple liner shapes.MAINSHAFT ASSEMBLYECCENTRIC ASSEMBLYFULLER-TRAYLOR COUNTERSHAFT STANDARD FEATURESTRIPLE CLIPPER TACONITE COUNTERSHAFT OIL SEAL STANDARDFULLER-TRAYLOR MPI-300 MANTLE POSITION INDICATOSpecifications