+ All Categories
Home > Documents > NTP/AFNOR INTERFACE - static.bodet-time.com · NTP/AFNOR INTERFACE rf.: 643531 f 1216...

NTP/AFNOR INTERFACE - static.bodet-time.com · NTP/AFNOR INTERFACE rf.: 643531 f 1216...

Date post: 07-May-2020
Category:
Upload: others
View: 17 times
Download: 0 times
Share this document with a friend
2
NTP/AFNOR INTERFACE Réf.: 643531 F 12/16 Non-contractual document. © 2016, Bodet SA. All rights reserved. [email protected] >> www.bodet-time.com << TECHNICAL FEATURES Construction......................................... Polycarbonate casing reinforced with fiberglass. Power supply........................................ PoE Ethernet network (20mA at 48V) Synchronisations.................................. In unicast, multicast or by DHCP. CONFIGURATION The interface can be connected to an Ethernet network delivering Network Time Protocol messages (NTP). Settings from embedded web server. CONNECTION One RJ45 compatible Ethernet PoE should be used to connect the interface to the Ethernet network (PoE) in 10Base-T through a Category 5 cable minimum or Category 6 (straight cable). In case the Ethernet network is not POE compatible, a 2-terminal connector is used to power the interface through a 12/35VDC TBT power supply unit. On the output side, a 4-terminal connector distributes the AFNOR signal and the power for the slave clock. The output power available on this connector is limited to 100mA from a PoE network or 0.5 A from a power supply for a non PoE network (Ref: 927222 only). ENVIRONMENT Temperature.......................................... -5 to +55°C. Humidity................................................ 0 to 80%. Time accuracy....................................... +/-100ms through synchronisation. REFERENCES 927 223................................................. PoE injector 927 228................................................. Unicast,multicast or DHCP NTP / AFNOR Interface 938 914................................................. Power supply for installation in trunking box 938 916................................................. Plug-in adapter APPLICATIONS To converter an Ethernet network time signal (NTP protocol) into an AFNOR signal (NFS 87500 A). STANDARDS EN 60950. EN 55022. EN 55024. Dimensions in mm See product page on >> www.bodet-time.com << 60 22 90
Transcript
Page 1: NTP/AFNOR INTERFACE - static.bodet-time.com · NTP/AFNOR INTERFACE rf.: 643531 f 1216 eportbodet.com non-contractual document. 216 odet sa. all rights resered. Power suPPly • In

nTP/AFnOR inTERFACE

Réf.:

643

531

F 12

/16

Non-contractual document. © 2016, Bodet SA. All rights [email protected]

>> www.bodet-time.com <<

Technical feaTures•construction......................................... Polycarbonate casing reinforced with fiberglass.•Power supply........................................ PoE Ethernet network (20mA at 48V)•synchronisations.................................. In unicast, multicast or by DHCP.

configuraTion

•The interface can be connected to an Ethernet network delivering Network Time Protocol messages (NTP).•Settings from embedded web server.

connecTion

•One RJ45 compatible Ethernet PoE should be used to connect the interface to the Ethernet network (PoE) in 10Base-T through a category 5 cable minimum or category 6 (straight cable).•In case the Ethernet network is not POE compatible, a 2-terminal connector is used to power the interface through a

12/35VDC TBT power supply unit.•On the output side, a 4-terminal connector distributes the AFNOR signal and the power for the slave clock.•The output power available on this connector is limited to 100mA from a PoE network or 0.5 A from a power supply for a non

PoE network (Ref: 927222 only).

enVironMenT•Temperature.......................................... -5 to +55°C.•humidity................................................ 0 to 80%.•Time accuracy....................................... +/-100ms through synchronisation.

references•927 223................................................. PoE injector•927 228................................................. Unicast,multicast or DHCP NTP / AFNOR Interface•938 914................................................. Power supply for installation in trunking box•938 916................................................. Plug-in adapter

aPPlicaTions

•To converter an Ethernet network time signal (NTP protocol) into an AFNOR signal (NFS 87500 A).

sTanDarDs

•EN 60950.•EN 55022.•EN 55024.

Dimensions in mm

See product page on >> www.bodet-time.com <<

60 22

90

Page 2: NTP/AFNOR INTERFACE - static.bodet-time.com · NTP/AFNOR INTERFACE rf.: 643531 f 1216 eportbodet.com non-contractual document. 216 odet sa. all rights resered. Power suPPly • In

nTP/AFnOR inTERFACE

Réf.:

643

531

F 12

/16

Non-contractual document. © 2016, Bodet SA. All rights [email protected]

>> www.bodet-time.com <<

Power suPPly

•In the case of a PoE powered interface, the output power of the interface is limited to 100mA to supply the TBT clocks.• In a non PoE network, the interface can be power by either a PoE injector or a TBT ( 12-35 VDC) power supply.

(Ref: 927222 only).

nTP Poe clock sysTeM

no-Poe clock sysTeM (ref : 927222 only)

AFNOR distribution + power supply 100 mA maximum.

AFNOR distribution + power supply in the range 12-35 VDC 500 mA maximum.

Power supply 12 to 35 VDCNTP

TBT or 230 V power supply

TBT or 230 V power supply

NTP PoE


Recommended