48

20 45

41 46

2728 44

31 42

35

34

2

36

37

1

12

17

141516

3

3029

6

2625

23

24

4225

13

3378932311011

31

31

43

6

19

2

18

21

42 43 42

474247

47

38

41

39 39

2131

21 31

21

1821 21

ITEM: PART No: Description Comments: QTY.

1 237657 TT.4055 BOTTOM TANK MOULDING (GRAPHITE) 1

237689 TT.4055 BOTTOM TANK MOULDING (GRAPHITE) EP 1

2 206111 HOSE CLOSURE 2

3 202008 MOTOR CAP GASKET 1

4 304417 MAINS MOTOR MOUNT WELD ASSEMBLY 1

5 205443 230V 2 STAGE D.I BYPASS ACUSTEK MOTOR (BL21104T) (MARKED 230V) TCO 1

321935 120V VAC MOTOR ASSEMBLY C/W 170MM LONG MOTOR LEAD 1

6 219569 NO8.1/2 INCH. LG.POZI-PAN.SCREW.STAINLESS STEEL.PLASTITE 4

7 219310 RUBBER WASHER 1

8 212052 3MM THICK X 9MM WIDE INSEAL (700MM LONG) 1

9 392441 TT4045/55 VAC MOTOR BACK PLATE 1

10 237526 38MM RED DRAIN HOSE CONNECTOR 1

11 206116 BLACK NUT 1

12 901539 ELBOW ANGLE CONNECTOR 3/8 PARALLEL THREAD C/W O-RING TO 12MM PUSH IN 1

13 213025 DUMP HOSE 1

14 208956 SILENCER FOAM TUBE 150MM 1

15 208583 DIP MOULDED ELBOW (MAINS VERSION) 1

16 902133 SPRING WIRE CLAMP (YDNAC-Y8010356) 1

17 901916 28mm HOSE CLIP 1

18 237754 35-38MM HOSE CLIP 2

19 219668 M5 X 10MM LONG POZI PAN STAINLESS STEEL SCREW 2

20 237691 SQUEEGEE LIFT HANDLE 1

21 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 9

22 208801 TT MOTOR GASKET 1

23 208799 TT MOTOR PLATE GASKET 1

24 219740 M5 X 12MM LONG STAINLESS STEEL POZI PAN SCREW 4

25 219861 M5 SINGLE COIL STAINLESS STEEL WASHER 4

26 219355 M5 FORM A STAINLESS STEEL WASHER 4

27 291118 M5 STAINLESS STEEL WASHER 19MM OD 1

28 208962 TT LIFTING WIRE 1

29 219721 M5 STAINLESS STEEL FULL NUT 1

30 219633 M5 STAINLESS STEEL NYLON INSERT NUT 1

31 219547 M5 X 16MM LONG POZI PAN STAINLESS STEEL SCREW 11

32 219644 M5 FORM G STAINLESS STEEL WASHER 4

33 202069 BOTTOM MOTOR GASKET 1

34 207128 CLEAN TANK INLET FILTER 1

35 237268 FILLER CAP LID 1

36 208960 TTB/TT FILLING HOSE 1

37 220403 CABLE CLIP 2

38 404216 HANDLE MOUNT WELD ASSEMBLY - Z/PL 1

39 392445 HANDLE MOUNT COVER PAINT GREY 2

40 219558 M5 STAINLESS STEEL NUTSERT 7

41 291124 M10 PENNY WASHER STAINLESS STEEL 2

42 219716 M8 FORM G STAINLESS STEEL WASHER 8

43 219639 M8 STAINLESS STEEL NYLON INSERT NUT 4

44 219686 M4 X 20MM LONG STAINLESS STEEL POZI PAN MACHINE SCREW 1

45 219687 M4 STAINLESS STEEL NYLON INSERT NUT 1

46 219895 M10 X 35MM LONG HEXAGONAL STAINLESS STEEL SCREW 1

47 291123 M8 X 75 LONG HEX HEAD BOLT STAINLESS STEEL 4

48 219897 M10 STAINLESS STEEL NYLON INSERT NUT 1

Numatic International Spare PartsModel No:

DRAWING: DRW-16829 ISS:A08Numatic International Spare PartsModel No:04/02/2016

TT4045 (TT1117) & TTB4055 (TT1120) BOTTOM TANK / VAC MOTOR ASSEMBLY

TT4045 (TT1117) & TTB4055 (TT1120) BOTTOM TANK / VAC MOTOR ASSEMBLY

244497Internal Code:

PRO

NB: FOR WIRING SEE DRAWING: DRW-18548, DRW-17307, DRW-17309, DRW-18468

37

66

16

38

45

42

43

41

50

51

52

54

53

56

57

2025

30

26

2349

5

59

60

61

62

63

28

2221

19 18 126

1636

15 14

3

1

748

13

11

47

48

46

39 40

3233

34

31

2935

53

49

66

9210 24

1764

2

9

64

27

14

44

58

2221

55

65

ITEM: PART No: Description Comments QTY.1 204021 12.7MM STAINLESS STEEL HUB CAP 22 204068 3 INCH GREY WHEEL 43 206236 PIVOT PIN 24 219394 COMPRESSION SPRING 15 219606 BRACKET SPACER 46 220348 SOLENOID VALVE 240V 50/60HZ 1

220349 SOLENOID VALVE 220V60HZ 1220350 SOLENOID VALVE 110V 50/60HZ 1

7 223242 PLUNGER MOUNTING PLATE MOULDING 18 229128 PLUNGER 19 219644 M5 FORM G STAINLESS STEEL WASHER 410 206013 BUFFER WHEEL PIN 211 208011 MOTOR MOUNTING SPACER 412 219009 M4 BRASS TAPPEX INSERT 213 229025 STANDARD GROMMET 414 229382 REAR WHEEL PIN 215 229258 TT 345 GRAPHITE BASE MOULDING 116 219568 NO8.3/4 INCH LG.POZI-PAN.SCREW.STAINLESS STEEL.PLASTITE 617 219355 M5 FORM A STAINLESS STEEL WASHER 218 219688 M4 FORM A STAINLESS STEEL WASHER 219 219703 M4 X 35MM LONG STAINLESS STEEL POZI PAN SCREW 220 219345 12MM EXTERNAL CIRCLIP 221 219647 M6 FORM G STAINLESS STEEL WASHER 422 219642 M6 STAINLESS STEEL NYLON INSERT NUT 423 392249 DECK MOUNT RH 124 392248 DECK MOUNT BRACKET 125 219984 M6 X 30MM LG POZI-PAN STAINLESS STEEL MACHINE SCREW 426 219639 M8 STAINLESS STEEL NYLON INSERT NUT 227 219718 WASHER.M6.SPRING.STAINLESS STEEL 428 229644 450MM DIAMETER SPLASH SKIRT MOULDING 129 219890 M4 X 12MM LONG POZI PAN STAINLESS STEEL SCREW 130 230094 62MM O/D X 30MM I/D X 20MM BEARING (WITH SEALS) 131 219453 M8 MULTISERT 132 291060 M6 SHAKEPROOF STAINLESS STEEL WASHER 433 219982 M6 X 40MM LONG POZI PAN STAINLESS STEEL SCREW 434 229971 CAP MOULDING 135 206823 230V SINGLE SPEED VOLTAGE RELAY 1

206822 110V/120V VOLTAGE RELAY 1208416 120V RELAY NACE MACHINES ONLY 1

36 291132 M5 X 16MM LONG STAINLESS STEEL POZI PAN SEMS SCREW 237 206753 UNIVERSAL POWER SUPPLY 138 237071 NPR / TT GRAPHITE LID MOULDING 139 220584 RENDAR CLIP IN PLUG 140 229213 PLUG COVER 141 219914 NO6 X 5/8 INCH LONG POZI-PAN PLASTITE STAINLESS STEEL SCREW 142 229972 FAN GUARD MOULDING 143 205072 PROCESSED 12V DC BRUSHLESS FAN 144 220876 20 MFD MOTOR RUN CAPACITOR (450V) 220V & 230V MACHINES 1

208211 80uF MOTOR RUN CAPACITOR 120V MACHINES 1208219 70uF RUN CAPACITOR 110V MACHINES 1

45 208265 MOTOR START CAPACITOR 100 MFD C/W RESISTOR & M8 STUD 220V & 230V MACHINES 1208210 MOTOR START CAPACITOR 480 MFD C/W RESISTOR & M8 STUD 110V & 120V MACHINES 1

46 328132 GRAPHITE MOTOR COWL MOULDING PRINTED PRINTED NUMATIC 1330008 TWINTEC MAINS MOTOR COWL MOULDING (GRAPHITE) (NO LOGO) NO PRINT 1

47 205217 COMBINED INDUCTION MOTOR 4POLE 220-240V 50Hz 1205219 COMBINED INDUCTION MOTOR 4POLE 220V 60Hz 1205220 COMBINED INDUCTION MOTOR 4POLE 120V 60Hz 1205221 COMBINED INDUCTION MOTOR 4POLE 110V 50Hz 1

48 227556 TOP MOTOR GASKET 149 230001 V OIL SEAL 250 214115 GEAR BOX MID SECTION 151 208207 GEARBOX FASTENER WITH SLOT 352 230015 15MM EXTERNAL CIRCLIP 353 230215 35MM X 15 I/D ALUMINIUM WASHER 654 230013 48 TOOTH SPUR GEAR(STANDARD SPEED 50/60HZ) 355 230027 12 TOOTH PINION GEAR (STANDARD SPEED) 156 230291 PLANET CARRIER & PIN ASSEMBLY (50HZ STANDARD SPEED) 157 230158 VITON OIL SEAL (BROWN) 158 230200 62MM INTERNAL CIRCLIP 159 230208 DIE CAST BOTTOM PLATE ASSY INCLUDE: 57, 58, 30 160 219706 M5 X 45MM LONG STAINLESS STEEL HEXAGONAL BOLT 361 219904 M5 X16MM LONG HEXAGONAL STAINLESS STEEL BOLT 362 230207 DIE CAST CHUCK MACHINED 163 230048 26MM EXTERNAL CIRCLIP 164 291133 M5 X 20MM LONG STAINLESS STEEL POZI PAN SEMS SCREW 265 291145 M4 SHAKEPROOF WASHER STAINLESS STEEL 166 291061 No6 X 1/.2 INCH LONG POZI PAN PLASTITE SCREW (STAINLESS STEEL) 3

Numatic International Spare PartsModel No:

DRAWING: DRW-13427 ISS:A16Numatic International Spare PartsModel No:19/01/2016

NB: FOR WIRING SEE DRAWING: DRW-18548, DRW-17307, DRW-17309, DRW-18468, DRW-11855, DRW-12474, DRW-12545

450MM MAINS DECK ASSEMBLY EXPLODED DRAWING 450MM MAINS DECK ASSEMBLY EXPLODED DRAWING

234956

19

32

20

18

23

30

3733

2629

28

47

27

21

25

44

48

31

45

17

74

66

56

50

55

54

7951

5253

362 6173

4

5

2

6

1 7

68

22

69

63

81 80

40

3611 1635

42

41

575859

12

60

4938

14

15

13 34

43

46

67

9

8

24

10

52

52

65

39

3

73

71

72

37

67

46 42

37

42

4444

47

35

42

4440

17

75

78

64

71

72

70

45 37

44

76

22

77

ITEM: PART No: Description Comments: QTY.1 229081 HANDLE CASTING MACHINED 12 229074 ADJUSTMENT GEAR 13 219254 O RING 3MM DIA X 60MM I/D 24 229073 GEAR LOCKING PIN 15 229138 SPRING 16 219099 M6 HALF NUT 17 229099 25MM DIA HOLE PLUG 18 338269 CROSS TUBE 19 227576 FRONT INNER HALF MOULDING 1

229508 FLAME RETARDANT FRONT INNER HALF MOULDING FLAME RETARDANT CSA SPEC 110 227577 REAR INNER HALF MOULDING 1

329484 MODIFIED REAR INNER HALF MOULDING (CSA SPEC) FLAME RETARDANT CSA SPEC 111 303526 NUTSERTED RELAY MOUNTING BRACKET 112 229748 FRONT COVER MOULDING (MAINS & BATTERY) 1

229750 MAINS FRONT COVER MOULDING (C/B HOLE) 110V/50HZ MACHINES 1229751 MAINS FRONT COVER MOULDING (C/B HOLE)(FLAME RETARDANT) 120V/60HZ FLAME RETARDENT MACHINES 1

13 220812 230V NEON INDICATOR & RED LENS 1220813 120V NEON INDICATOR & RED LENS 1

14 227585 LEFT HAND SWITCH OPERATING LEVER MOULDING 115 227586 RIGHT HAND SWITCH OPERATING LEVER MOULDING 116 227587 CENTRE SWITCH OPERATING LEVER MOULDING 117 227580 HAND GRIP MOULDING 218 227583 ADJUSTMENT LEVER MOULDING 119 219493 M6 NYLON WASHER 120 219088 M6 NYLON INSERT NUT 121 227676 REAR COVER 1

229507 MAINS TYPE FLAME RETARDANT REAR COVER MOULDING FLAME RETARDANT CSA SPEC 122 229009 BLANKING PLUG 223 227584 INTERLOCK LEVER MOULDING 124 227582 HANDLE PLUG MOULDING 125 227691 TERMINAL BLOCK 1

229510 FLAME RETARDANT TERMINAL BLOCK FLAME RETARDANT CSA SPEC 126 227680 TERMINAL BLOCK COVER 1

229511 FLAME RETARDANT TERMINAL BLOCK COVER FLAME RETARDANT CSA SPEC 127 206562 CONTACT PIN 228 206563 EARTH CONTACT PIN 129 219090 M4 X 8MM LONG POZI PAN SEMS SCREW 330 227678 SOCKET COVER 1

229512 FLAME RETARDANT INLET COVER FLAME RETARDANT CSA SPEC 131 227008 BLACK CABLE CLAMP 232 20638V 19MM BLACK TUBE END STOP 133 216290 CABLE CLAMP 134 206575 240V / 25A RELAY 1

206576 100V-120V / 25A RELAY 135 229483 SNAP ACTION SWITCH 236 219805 4MM SPIREFIX 137 219107 No6 X 5/8 INCH LONG POZI PAN PLASTITE SCREW 838 219471 M4 X 12MM LONG POZI PAN SEMS SCREW 239 219560 M6 FORM B STAINLESS STEEL WASHER 240 219803 TRIGGER COMPRESSION SPRING 241 219804 SWITCH COMPRESSION SPRING 142 219569 NO8.1/2 INCH. LG.POZI-PAN.SCREW.STAINLESS STEEL.PLASTITE 1043 219811 NO8 X 1 INCH LONG POZI-PAN SELF TAP SCREW 244 219105 No8 X 5/8 INCH LONG POZI PAN PLASTITE SCREW 845 219206 M4 FORM A WASHER 246 219270 No8 X 1/2 INCH LONG POZI PAN SELF TAP SCREW 247 219568 NO8.3/4 INCH LG.POZI-PAN.SCREW.STAINLESS STEEL.PLASTITE 348 219005 M5 FORM G WASHER 149 270146 GREEN ILLUMINATED SWITCH + MEMBRANE 250 236012 20.0M X 1.50MM X 3 CORE NUCABLE (UK PLUG) 1

236132 20M X 1.5MM X 3 CORE YELLOW CABLE X SOCKET (EURO PLUG) 1236020 20.0M X 1.5MM X 3 CORE NUCABLE (SWISS PLUG) 1236024 20.0M X 1.50MM X 3 CORE NUCABLE (SOUTH AFRICAN PLUG) 1236068 20.0MT X 1.5MM X 3 CORE CABLE (16A SOCKET + 10A PLUG) AUSTRALIAN 1236118 20.0M X 1.5MM X 3 CORE NUCABLE (16 AMP INDUSTRIAL PLUG) 1236028 20.0M X 14AWG X 3 CORE YELLOW NUCABLE (CSA PLUG) 1

51 227806 CABLE RELEASE BASE MOULDING 152 219644 M5 FORM G STAINLESS STEEL WASHER 353 219076 M5 NYLON INSERT NUT 154 227807 CABLE RELEASE TOP MOULDING 155 206599 SPRING (REF:C5514370) 156 219720 M5 X 30MM LONG STAINLESS STEEL POZI PAN SCREW 157 206500 RELAY BRACKET 158 220440 8 AMP OVERLOAD 120V/60HZ FLAME RETARDENT MACHINES 1

208550 15 AMP OVERLOAD 110V/50HZ MACHINES 159 219702 M10 INTERNAL LOCK WASHER 110V & 120V MACHINES 160 220459 OVERLOAD DUST COVER 110V & 120V MACHINES 161 219632 M8 STAINLESS STEEL DOME NUT 362 219018 M8 SHAKEPROOF WASHER 363 219922 M8 X 50MM LONG SOCKET BUTTON HEAD STAINLESS STEEL BOLT 364 291125 M6 X 40 LONG HEX BOLT STAINLESS STEEL 265 219764 M6 STAINLESS STEEL DOME NUT 266 229461 440MM HANDLE LOCKING ROD 167 229500 TRIGGER MOULDING BLUE 2

227581 TRIGGER MOULDING (GREY) 268 330231 TTB/TT 430MM PROCESSED ALI HANDLE PAINT GREY 169 237692 HANDLE CABLE COVER L/H 170 237693 HANDLE CABLE COVER R/H 171 219740 M5 X 12MM LONG STAINLESS STEEL POZI PAN SCREW 272 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 273 219578 M8 FORM A STAINLESS STEEL WASHER 674 291133 M5 X 20MM LONG STAINLESS STEEL POZI PAN SEMS SCREW 175 291128 M6 X 50 LONG HEX BOLT STAINLESS STEEL 276 392437 RETAINER SPACER 277 219718 WASHER.M6.SPRING.STAINLESS STEEL 278 219544 M6 SHAKEPROOF WASHER 479 219642 M6 STAINLESS STEEL NYLON INSERT NUT 280 219743 CABLE CLEAT 181 902312 CABLE STRESS RELIEF 1

Numatic International Spare PartsModel No:

DRAWING: DRW-16831 ISS:A06Numatic International Spare PartsModel No:26/01/2016

NB: FOR WIRING SEE DRAWING: DRW-18548, DRW-17307, DRW-17309, DRW-18468TT4045 (TT1117) & TT4055 (TT1120) HANDLE ASSEMBLY TT4045 (TT1117) & TT4055 (TT1120) HANDLE ASSEMBLY

244495

22

35

23

21

26 3340362932 3150 30

24

28

46

54

34

4919

6

58

52

575667535455

3639

4

5

2

7

1 8

69

25

7147

65

70

43

3913 1838

73 4459

6061

14

62

51

41

16

1715

3745

74

20

11

10

27

12

5454

6742

3 9

47

72

20

74

73

40

7373464650387346

43

19

6668

42

66

71

47

42

71

64

7576 48

ITEM PART No: DESCRIPTION COMMENTS QTY.1 304437 PROCESSED HANDLE CASTING 12 229074 ADJUSTMENT GEAR 13 219254 O RING 3MM DIA X 60MM I/D 24 229073 GEAR LOCKING PIN 15 229138 SPRING 16 229462 510MM HANDLE LOCKING ROD 17 219099 M6 HALF NUT 18 229099 25MM DIA HOLE PLUG 19 219578 M8 FORM A STAINLESS STEEL WASHER 610 338269 CROSS TUBE 111 227576 FRONT INNER HALF MOULDING 1

229508 FLAME RETARDANT FRONT INNER HALF MOULDING FLAME RETARDANT CSA SPEC 112 227577 REAR INNER HALF MOULDING 1

329484 MODIFIED REAR INNER HALF MOULDING (CSA SPEC) FLAME RETARDANT CSA SPEC 113 303526 NUTSERTED RELAY MOUNTING BRACKET 114 229748 FRONT COVER MOULDING (MAINS & BATTERY) 230V/50-60HZ MACHINES 1

229750 MAINS FRONT COVER MOULDING (C/B HOLE) 110V/50HZ MACHINES 1229751 MAINS FRONT COVER MOULDING (C/B HOLE)(FLAME

RETARDANT) 120V/60HZ FLAME RETARDENT MACHINES 115 220812 230V NEON INDICATOR & RED LENS 1

220813 120V NEON INDICATOR & RED LENS 116 227585 LEFT HAND SWITCH OPERATING LEVER MOULDING 117 227586 RIGHT HAND SWITCH OPERATING LEVER MOULDING 118 227587 CENTRE SWITCH OPERATING LEVER MOULDING 119 227580 HAND GRIP MOULDING 220 227581 TRIGGER MOULDING GREY 221 227583 ADJUSTMENT LEVER MOULDING 122 219493 M6 NYLON WASHER 123 219088 M6 NYLON INSERT NUT 124 227676 REAR COVER 1

229507 MAINS TYPE FLAME RETARDANT REAR COVER MOULDING FLAME RETARDANT CSA SPEC 125 229009 BLANKING PLUG 126 227584 INTERLOCK LEVER MOULDING 127 227582 HANDLE PLUG MOULDING 128 227691 TERMINAL BLOCK 1

229510 FLAME RETARDANT TERMINAL BLOCK FLAME RETARDANT CSA SPEC 129 227680 TERMINAL BLOCK COVER 1

229511 FLAME RETARDANT TERMINAL BLOCK COVER FLAME RETARDANT CSA SPEC 130 206562 CONTACT PIN 231 206563 EARTH CONTACT PIN 132 219090 M4 X 8MM LONG POZI PAN SEMS SCREW 333 227678 SOCKET COVER 1

229512 FLAME RETARDANT INLET COVER FLAME RETARDANT CSA SPEC 134 227008 BLACK CABLE CLAMP 2

329485 BLACK CABLE CLAMP FLAME RETARDANT CSA SPEC 135 20638V 19MM BLACK TUBE END STOP 136 216290 CABLE CLAMP 137 206575 240V / 25A RELAY 1

206576 100V-120V / 25A RELAY 138 229483 SNAP ACTION SWITCH 239 219805 4MM SPIREFIX 140 219107 No6 X 5/8 INCH LONG POZI PAN PLASTITE SCREW 741 219471 M4 X 12MM LONG POZI PAN SEMS SCREW 242 219560 M6 FORM B STAINLESS STEEL WASHER 643 219803 TRIGGER COMPRESSION SPRING 244 219804 SWITCH COMPRESSION SPRING 145 219811 NO8 X 1 INCH LONG POZI-PAN SELF TAP SCREW 246 219370 No8 X 5/8 INCH LONG PLASTITE STAINLESS STEEL SCREW 647 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 448 291133 M5 X 20MM LONG STAINLESS STEEL POZI PAN SEMS SCREW 149 219206 M4 FORM A WASHER 250 219568 NO8.3/4 INCH LG.POZI-PAN.SCREW.STAINLESS STEEL.PLASTITE 351 270146 GREEN ILLUMINATED SWITCH + MEMBRANE 252 236012 20.0M X 1.50MM X 3 CORE NUCABLE (UK PLUG) 1

236132 20M X 1.5MM X 3 CORE YELLOW CABLE X SOCKET (EURO PLUG) 1236020 20.0M X 1.5MM X 3 CORE NUCABLE (SWISS PLUG) 1236024 20.0M X 1.50MM X 3 CORE NUCABLE (SOUTH AFRICAN PLUG) 1236068 20.0MT X 1.5MM X 3 CORE CABLE (16A SOCKET + 10A PLUG)

AUSTRALIAN 1236118 20.0M X 1.5MM X 3 CORE NUCABLE (16 AMP INDUSTRIAL PLUG) 1236028 20.0M X 14AWG X 3 CORE YELLOW NUCABLE (CSA PLUG) 1

53 227806 CABLE RELEASE BASE MOULDING 154 219644 M5 FORM G STAINLESS STEEL WASHER 455 291035 M5 NYLON INSERT NUT (STAINLESS STEEL) 156 227807 CABLE RELEASE TOP MOULDING 157 206599 SPRING (REF:C5514370) 158 219720 M5 X 30MM LONG STAINLESS STEEL POZI PAN SCREW 159 206500 RELAY BRACKET 160 220440 8 AMP OVERLOAD 120V/60HZ FLAME RETARDENT MACHINES 1

208550 15 AMP OVERLOAD 110V/50HZ MACHINES 161 219702 M10 INTERNAL LOCK WASHER 110V & 120V MACHINES 162 220459 OVERLOAD DUST COVER 110V & 120V MACHINES 163 219632 M8 STAINLESS STEEL DOME NUT 364 902520 WASHER M8 SHAKEPROOF STAINLESS STEEL 365 219922 M8 X 50MM LONG SOCKET BUTTON HEAD S/ STEEL BOLT 366 291125 M6 X 40 LONG HEX BOLT STAINLESS STEEL 467 219764 M6 STAINLESS STEEL DOME NUT 468 392298 TWINTEC HANDLE CLAMP 169 404159 (404159) 500MM PROCESSED & PAINTED HANDLE 170 404165 TT HANDLE COVER - PAINTED ANTHRACITE GREY 171 291004 M5 X 10MM LONG STAINLESS STEEL BUTTON HEAD SCREW 472 219914 NO6 X 5/8 INCH LONG POZI-PAN PLASTITE S/STEEL SCREW 173 219569 NO8.1/2 INCH. LG.POZI-PAN.SCREW.STAINLESS STEEL.PLASTITE 1074 219270 No8 X 1/2 INCH LONG POZI PAN SELF TAP SCREW 275 219743 CABLE CLEAT 176 902312 CABLE STRESS RELIEF 1

Numatic International Spare PartsModel No:

DRAWING: DRW-13430 ISS:A12Numatic International Spare PartsModel No:27/01/2016

NB: FOR WIRING SEE DRAWING: DRW-11855, DRW-12474, DRW-12545

TT4045 (TT1117) & TT4055 (TT1120) & ET4045 (ET1117) HANDLE ASSEMBLY EXPLODED DRAWING

TT4045 (TT1117) & TT4055 (TT1120) & ET4045 (ET1117) HANDLE ASSEMBLY EXPLODED DRAWING

234958Internal Code:

PRO

41

19

18

40

1714

22

20236

29 281 27

125

34

7

2

15

6

16

16

21

26

2425

3113

34

35

33

10

32

11

20

11

20

15

42 39

131111

3

26

25

24

11 11

36

1

29

37

26

25

24

3121

15 16 15 38

38 13

262524

38

8d

8c

8b

8a

9a

4344

4546

38

30

479

8

ITEM: PART No: DESCRIPTION COMMENTS: QTY

1 206713 80MM DIAMETER BLACK WHEEL 2

2 304378 FLOOR TOOL PIVOT TUBE (OLD STYLE FLOOR TOOL) 1

3 206964 SLIDE NYLON SPACER 4

4 206954 SPIRO SPACER 2

5 902522 M6 X 40MM LONG SOCKET BUTTON HEAD STAINLESS STEEL BOLT 1

6 219642 M6 STAINLESS STEEL NYLON INSERT NUT 2

7 304359 TT/TTB/4045/4055 SQUEEGEE MOUNT WELD ASSEMBLY 1

8 208888 EXTENDED STRAINER 1

8a 208890 EXTENDED STRAINER CLEAR BOWL SPARE ITEM 1

8b 208830 STRAINER GASKET SPARE ITEM 1

8c 208889 EXTENDED STRAINER 50 MESH SCREEN SPARE ITEM 1

8d 208827 STRAINER BLACK TOP SPARE ITEM 1

9 901542 12MM PUSH FIT TO 10MM HOSE TAIL BALL VALVE ASSEMBLY 1

9a 901544 TAP HANDLE C/W COVER AND M3X6MM SCREW (SPARE ITEM) SPARE ITEM 1

10 304453 NUTSERTED 10MM TAP BRACKET 1

11 208312 IGUS BEARING (GFM 101205) 6

12 208574 M8 X 10 X 60 SHOULDER BOLT 1

13 237632 SHOULDER BOLT COVER 3

14 219631 19MM GROMMET 1

15 219578 M8 FORM A STAINLESS STEEL WASHER 4

16 219639 M8 STAINLESS STEEL NYLON INSERT NUT 3

17 208771 TPR OPEN GROMMET 1

18 304358 DECK LOCK BAR WELD ASSEMBLY 1

19 208578 DECK LOCK SPRING 1

20 291132 M5 X 16MM LONG STAINLESS STEEL POZI PAN SEMS SCREW 4

21 208638 160mm WHEEL WITH POLYURETHENE TYRE 2

22 321902 SILENCER CLAMP 1

23 291167 M6 X 70MM LONG HEX HEAD BOLT STAINLESS STEEL 1

24 219719 M6 X 16MM LONG HEXAGONAL STAINLESS STEEL HEAD BOLT 5

25 219718 WASHER.M6.SPRING.STAINLESS STEEL 5

26 219647 M6 FORM G STAINLESS STEEL WASHER 5

27 219897 M10 STAINLESS STEEL NYLON INSERT NUT 2

28 391440 1/2 INCH X 18G X 41MM LONG STAINLESS STEEL SPACER TUBE 2

29 219894 M10 X 60MM LONG HEXAGONAL STAINLESS STEEL BOLT 2

30 219355 M5 FORM A STAINLESS STEEL WASHER 1

31 291057 M8 X 10 X 55MM LONG HEX SOCKET SHOULDER BOLT 2

32 391216 SILICON TUBE 8MM I/D X 3.2MM WALL SECTION (CUT 600MM) 1

33 391215 SILICON TUBE 200MM LONG X 8MM I/D X 3.2MM WALL SECTION 1

34 901545 ELBOW ANGLE CONNECTOR 12MM PUSH IN TO 12MM STEM 1

35 901552 NYLON TUBE 12MM OD X 10MM ID (50MM) 1

36 208619 FLOOR TOOL SPRING 1

37 900277 TT/4045/4055 CHASSIS WELD ASSY (12SWG M/S) PAINT GREY 1

38 219903 M10 FORM A STAINLESS STEEL WASHER 4

39 901279 LATCH BLOCK TOP MOULDING 1

40 901280 LATCH BLOCK BOTTOM MOULDING 1

41 901558 M5 X 60MM STAINLESS STEEL POZI PAN MACHINE SCREW 3

42 219633 M5 STAINLESS STEEL NYLON INSERT NUT 3

43 901006 FILTER MOUNTING BRACKET 1

44 219644 M5 FORM G STAINLESS STEEL WASHER 2

45 219861 M5 SINGLE COIL STAINLESS STEEL WASHER 2

46 219571 M5 X 20MM LONG POZI PAN STAINLESS STEEL SCREW 2

47 219560 M6 FORM B STAINLESS STEEL WASHER 1

Numatic International Spare PartsModel No:

DRAWING: DRW-13478 ISS:A14Numatic International Spare PartsModel No:04/01/2016

TT4045 (TT1117) & TT4055 (TT1120) & ET4045 (ET1117) CHASSIS ASSEMBLY EXPLODED DRAWING

TT4045 (TT1117) & TT4055 (TT1120) & ET4045 (ET1117) CHASSIS ASSEMBLY EXPLODED DRAWING

234959Internal Code:

PRO

NB: FOR WIRING SEE DRAWING: DRW-1855, DRW-12474, DRW-12545

39

38

17

40

47

44

45

43

52

53

54

56

57

55

58

59

2127

32

28

2551

5

61

62

63

64

65

30

2423

2022 19 136

1763

1615

3

1

7

66

48

14

12

49

50

48

41 42

34

35

36

3331

37

55

51

38

92

11 26

18 10

2

669

1066

29

15

46

60

ITEM: PART No: Description Comments QTY.1 204021 12.7MM STAINLESS STEEL HUB CAP 22 204068 3 INCH GREY WHEEL 43 206236 PIVOT PIN 24 219394 COMPRESSION SPRING 15 219606 BRACKET SPACER 46 220348 SOLENOID VALVE 240V 50/60HZ 1

220349 SOLENOID VALVE 220V60HZ 1220350 SOLENOID VALVE 110V 50/60HZ 1

7 223242 PLUNGER MOUNTING PLATE MOULDING 18 229128 PLUNGER 19 219644 M5 FORM G STAINLESS STEEL WASHER 410 219571 M5 X 20MM LONG POZI PAN STAINLESS STEEL SCREW 211 206013 BUFFER WHEEL PIN 212 208011 MOTOR MOUNTING SPACER 413 219009 M4 BRASS TAPPEX INSERT 214 229025 STANDARD GROMMET 415 229382 REAR WHEEL PIN 216 229258 TT 345 GRAPHITE BASE MOULDING 117 219568 No8 X 3/4 INCH LONG POZI PAN STAINLESS STEEL SCREW 618 219355 M5 FORM A STAINLESS STEEL WASHER 219 219688 M4 FORM A STAINLESS STEEL WASHER 220 219703 M4 X 35MM LONG STAINLESS STEEL POZI PAN SCREW 221 219345 12MM EXTERNAL CIRCLIP 222 219251 REPLACEMENT MPM CONNECTOR M3 SCREW 123 219647 M6 FORM G STAINLESS STEEL WASHER 424 219642 M6 STAINLESS STEEL NYLON INSERT NUT 425 392249 DECK MOUNT RH 126 392248 DECK MOUNT BRACKET 127 219984 M6 X 30MM LG POZI-PAN STAINLESS STEEL MACHINE SCREW 428 219639 M8 STAINLESS STEEL NYLON INSERT NUT 229 219718 WASHER.M6.SPRING.STAINLESS STEEL 430 229644 450MM DIAMETER SPLASH SKIRT MOULDING 131 219471 M4 X 12MM LONG POZI PAN SEMS SCREW 132 230094 62MM O/D X 30MM I/D X 20MM BEARING (WITH SEALS) 133 219453 M8 MULTISERT 134 291060 M6 SHAKEPROOF STAINLESS STEEL WASHER 435 219982 M6 X 40MM LONG POZI PAN STAINLESS STEEL SCREW 436 229971 CAP MOULDING 137 206823 230V SINGLE SPEED VOLTAGE RELAY 1

206822 110V/120V VOLTAGE RELAY 1208416 120V RELAY NACE MACHINES ONLY 1

38 219318 No6 X 1/2 INCH LONG POZI PAN PLASTITE SCREW 339 206753 UNIVERSAL POWER SUPPLY 140 237071 NPR / TT GRAPHITE LID MOULDING 141 220584 RENDAR CLIP IN PLUG 142 229213 PLUG COVER 143 219914 NO6 X 5/8 INCH LONG POZI-PAN PLASTITE STAINLESS STEEL SCREW 144 229972 FAN GUARD MOULDING 145 205072 PROCESSED 12V DC BRUSHLESS FAN 146 220876 20 MFD MOTOR RUN CAPACITOR (450V) 220V & 230V MACHINES 1

208211 80uF MOTOR RUN CAPACITOR 120V MACHINES 1208219 70uF RUN CAPACITOR 110V MACHINES 1

47 208265 MOTOR START CAPACITOR 100 MFD C/W RESISTOR & M8 STUD 220V & 230V MACHINES 1208210 MOTOR START CAPACITOR 480 MFD C/W RESISTOR & M8 STUD 110V & 120V MACHINES 1

48 328132 GRAPHITE MOTOR COWL MOULDING PRINTED PRINTED NUMATIC 1330008 TWINTEC MAINS MOTOR COWL MOULDING (GRAPHITE) (NO LOGO) NO PRINT 1

49 205217 COMBINED INDUCTION MOTOR 4POLE 220-240V 50Hz 1205219 COMBINED INDUCTION MOTOR 4POLE 220V 60Hz 1205220 COMBINED INDUCTION MOTOR 4POLE 120V 60Hz 1205221 COMBINED INDUCTION MOTOR 4POLE 110V 50Hz 1

50 227556 TOP MOTOR GASKET 151 230001 V OIL SEAL 252 214115 GEAR BOX MID SECTION 153 208207 GEARBOX FASTENER WITH SLOT 354 230015 15MM EXTERNAL CIRCLIP 355 230215 35MM X 15 I/D ALUMINIUM WASHER 656 230013 48 TOOTH SPUR GEAR(STANDARD SPEED 50/60HZ) 357 230027 12 TOOTH PINION GEAR (STANDARD SPEED) 158 230291 PLANET CARRIER & PIN ASSEMBLY (50HZ STANDARD SPEED) 159 230158 VITON OIL SEAL (BROWN) 160 230200 62MM INTERNAL CIRCLIP 161 230208 DIE CAST BOTTOM PLATE ASSY INCLUDE: 60, 61, 33 162 219706 M5 X 45MM LONG STAINLESS STEEL HEXAGONAL BOLT 363 219904 M5 X16MM LONG HEXAGONAL STAINLESS STEEL BOLT 564 230207 DIE CAST CHUCK MACHINED 165 230048 26MM EXTERNAL CIRCLIP 166 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 4

Numatic International Spare PartsModel No:

DRAWING: DRW-13427 ISS:A05Numatic International Spare PartsModel No:19/11/2015

NB: FOR WIRING SEE DRAWING: DRW-18548, DRW-17307, DRW-17309, DRW-18468, DRW-11855, DRW-12474, DRW-12545

450MM MAINS DECK ASSEMBLY EXPLODED DRAWING 450MM MAINS DECK ASSEMBLY EXPLODED DRAWING

234956

40

39

18

41

48

47

45

46

44

53

54

55

57

5856

59

60

22 6128

33

29

2652

5

62

63

64

65

66

31

2524

2123 20 146

181017 16

3

1

30

7

67

48

15

13

50

51

49

42 43

35

36

37

3432

38

56

52

39

92

12 27

19 11

2

679

ITEM: PART No: Description Comments QTY.1 204021 12.7MM STAINLESS STEEL HUB CAP 22 204068 3 INCH GREY WHEEL 43 206236 PIVOT PIN 24 219394 COMPRESSION SPRING 15 219606 BRACKET SPACER 46 220348 SOLENOID VALVE 240V 50/60HZ 1

220350 SOLENOID VALVE 110V 50/60HZ 17 223242 PLUNGER MOUNTING PLATE MOULDING 18 229128 PLUNGER 19 219644 M5 FORM G STAINLESS STEEL WASHER 4

10 219547 M5 X 16MM LONG POZI PAN STAINLESS STEEL SCREW 211 219571 M5 X 20MM LONG POZI PAN STAINLESS STEEL SCREW 212 206013 BUFFER WHEEL PIN 213 208011 MOTOR MOUNTING SPACER 414 219009 M4 BRASS TAPPEX INSERT 215 229025 STANDARD GROMMET 416 229382 REAR WHEEL PIN 217 229258 TT 345 GRAPHITE BASE MOULDING 118 219568 No8 X 3/4 INCH LONG POZI PAN STAINLESS STEEL SCREW 619 219355 M5 FORM A STAINLESS STEEL WASHER 220 219688 M4 FORM A STAINLESS STEEL WASHER 221 219703 M4 X 35MM LONG STAINLESS STEEL POZI PAN SCREW 222 219345 12MM EXTERNAL CIRCLIP 223 219251 REPLACEMENT MPM CONNECTOR M3 SCREW 124 219647 M6 FORM G STAINLESS STEEL WASHER 425 219642 M6 STAINLESS STEEL NYLON INSERT NUT 426 392249 DECK MOUNT RH 127 392248 DECK MOUNT BRACKET 128 219984 M6 X 30MM LG POZI-PAN STAINLESS STEEL MACHINE SCREW 429 219639 M8 STAINLESS STEEL NYLON INSERT NUT 230 219549 M6 SINGLE COIL WASHER 431 229644 450MM DIAMETER SPLASH SKIRT MOULDING 132 219471 M4 X 12MM LONG POZI PAN SEMS SCREW 133 230094 62MM O/D X 30MM I/D X 20MM BEARING (WITH SEALS) 134 219453 M8 MULTISERT 135 219544 M6 SHAKEPROOF WASHER 436 219982 M6 X 40MM LONG POZI PAN STAINLESS STEEL SCREW 437 229971 CAP MOULDING 138 206823 230V SINGLE SPEED VOLTAGE RELAY 1

206822 110V/120V VOLTAGE RELAY 1208416 120V RELAY NACE MACHINES ONLY 1

39 219318 No6 X 1/2 INCH LONG POZI PAN PLASTITE SCREW 340 206753 UNIVERSAL POWER SUPPLY 141 237071 NPR / TT GRAPHITE LID MOULDING 142 220584 RENDAR CLIP IN PLUG 143 229213 PLUG COVER 144 219914 NO6 X 5/8 INCH LONG POZI-PAN PLASTITE STAINLESS STEEL SCREW 145 229972 FAN GUARD MOULDING 146 205072 PROCESSED 12V DC BRUSHLESS FAN 147 220876 20 MFD MOTOR RUN CAPACITOR (450V) 220V & 230V MACHINES 1

208211 80uF MOTOR RUN CAPACITOR 120V MACHINES 1208219 70uF RUN CAPACITOR 110V MACHINES 1

48 208265 MOTOR START CAPACITOR 100 MFD C/W RESISTOR & M8 STUD 220V & 230V MACHINES 1208210 MOTOR START CAPACITOR 480 MFD C/W RESISTOR & M8 STUD 110V & 120V MACHINES 1

49 328132 GRAPHITE MOTOR COWL MOULDING PRINTED PRINTED NUMATIC 1330008 TWINTEC MAINS MOTOR COWL MOULDING (GRAPHITE) (NO LOGO) NO PRINT 1

50 205217 COMBINED INDUCTION MOTOR 4POLE 220-240V 50Hz 1205219 COMBINED INDUCTION MOTOR 4POLE 220V 60Hz 1205220 COMBINED INDUCTION MOTOR 4POLE 120V 60Hz 1205221 COMBINED INDUCTION MOTOR 4POLE 110V 50Hz 1

51 227556 TOP MOTOR GASKET 152 230001 V OIL SEAL 253 214115 GEAR BOX MID SECTION 154 208207 GEARBOX FASTENER WITH SLOT 355 230015 15MM EXTERNAL CIRCLIP 356 230215 35MM X 15 I/D ALUMINIUM WASHER 657 230013 48 TOOTH SPUR GEAR(STANDARD SPEED 50/60HZ) 358 230027 12 TOOTH PINION GEAR (STANDARD SPEED) 159 230291 PLANET CARRIER & PIN ASSEMBLY (50HZ STANDARD SPEED) 160 230158 VITON OIL SEAL (BROWN) 161 230200 62MM INTERNAL CIRCLIP 162 230208 DIE CAST BOTTOM PLATE ASSY INCLUDE: 60, 61, 33 163 219706 M5 X 45MM LONG STAINLESS STEEL HEXAGONAL BOLT 364 219904 M5 X16MM LONG HEXAGONAL STAINLESS STEEL BOLT 365 230207 DIE CAST CHUCK MACHINED 166 230048 26MM EXTERNAL CIRCLIP 167 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 4

Numatic International Spare PartsModel No:

DRAWING: DRW-13427 ISS:A03Numatic International Spare PartsModel No:05/11/2014

NB: FOR WIRING SEE DRAWING: DRW-17307, DRW-17309, DRW-17314, DRW-1855, DRW-12474, DRW-12545

450MM MAINS DECK ASSEMBLY 450MM MAINS DECK ASSEMBLY

234956

48

20 45

41 46

2728 44

31 42

35

34

2

36

37

1

1217

141516

3

3029

6

2625

23

24

4225

13

3378932311011

31

31

43

6

19

2

21 18 18

21

42 43 42

474247

47

38

41

39 39

212131

21 31

21

ITEM: PART No: Description Comments: QTY.

1 237657 TT.4055 BOTTOM TANK MOULDING (GRAPHITE) 1

237689 TT.4055 BOTTOM TANK MOULDING (GRAPHITE) EP 1

2 206111 HOSE CLOSURE 2

3 202008 MOTOR CAP GASKET 1

4 304417 MAINS MOTOR MOUNT WELD ASSEMBLY 1

5 205443 230V 2 STAGE D.I BYPASS ACUSTEK MOTOR (BL21104T) (MARKED 230V) TCO 1

321935 120V VAC MOTOR ASSEMBLY C/W 170MM LONG MOTOR LEAD 1

6 219569 No8 X 1/2 INCH LONG POZI PAN STAINLESS STEEL PLASTITE SCREW 4

7 219310 RUBBER WASHER 1

8 212052 3MM THICK X 9MM WIDE INSEAL (700MM LONG) 1

9 392441 TT4045/55 VAC MOTOR BACK PLATE 1

10 237526 38MM RED DRAIN HOSE CONNECTOR 1

11 206116 BLACK NUT 1

12 901539 ELBOW ANGLE CONNECTOR 3/8 PARALLEL THREAD C/W O-RING TO 12MM PUSH IN 1

13 213025 600MM - 630MM LONG DUMP HOSE ASSEMBLY 1

14 208956 SILENCER FOAM TUBE 150MM 1

15 208583 DIP MOULDED ELBOW (MAINS VERSION) 1

16 902133 SPRING WIRE CLAMP (YDNAC-Y8010356) 1

17 206818 HOSE CLIP 1

18 237754 35-38MM HOSE CLIP 2

19 219668 M5 X 10MM LONG POZI PAN STAINLESS STEEL SCREW 2

20 237691 SQUEEGEE LIFT HANDLE 1

21 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 9

22 208801 TT MOTOR GASKET 1

23 208799 TT MOTOR PLATE GASKET 1

24 219740 M5 X 12MM LONG STAINLESS STEEL POZI PAN SCREW 4

25 219861 M5 SINGLE COIL STAINLESS STEEL WASHER 4

26 219355 M5 FORM A STAINLESS STEEL WASHER 4

27 291118 M5 STAINLESS STEEL WASHER 19MM OD 1

28 208962 TT LIFTING WIRE 1

29 219721 M5 STAINLESS STEEL FULL NUT 1

30 219633 M5 STAINLESS STEEL NYLON INSERT NUT 1

31 219547 M5 X 16MM LONG POZI PAN STAINLESS STEEL SCREW 11

32 219644 M5 FORM G STAINLESS STEEL WASHER 4

33 202069 BOTTOM MOTOR GASKET 1

34 207128 CLEAN TANK INLET FILTER 1

35 237268 FILLER CAP LID 1

36 208960 TTB/TT FILLING HOSE 1

37 220403 CABLE CLIP 2

38 404216 HANDLE MOUNT WELD ASSEMBLY - Z/PL 1

39 392445 HANDLE MOUNT COVER PAINT GREY 2

40 219558 M5 STAINLESS STEEL NUTSERT 7

41 291124 M10 PENNY WASHER STAINLESS STEEL 2

42 219716 M8 FORM G STAINLESS STEEL WASHER 8

43 219639 M8 STAINLESS STEEL NYLON INSERT NUT 4

44 219686 M4 X 20MM LONG STAINLESS STEEL POZI PAN MACHINE SCREW 1

45 219687 M4 STAINLESS STEEL NYLON INSERT NUT 1

46 219895 M10 X 35MM LONG HEXAGONAL STAINLESS STEEL SCREW 1

47 291123 M8 X 75 LONG HEX HEAD BOLT STAINLESS STEEL 4

48 219897 M10 STAINLESS STEEL NYLON INSERT NUT 1

Numatic International Spare PartsModel No:

DRAWING: DRW-16829 ISS:A07Numatic International Spare PartsModel No:02/11/2015

TT4045 (TT1117) & TTB4055 (TT1120) BOTTOM TANK / VAC MOTOR ASSEMBLY

TT4045 (TT1117) & TTB4055 (TT1120) BOTTOM TANK / VAC MOTOR ASSEMBLY

244497Internal Code:

PRO

NB: FOR WIRING SEE DRAWING: DRW-18548, DRW-17307, DRW-17309, DRW-18468

40

18

17

14

22

20386

28 271 26

12534

7

2

15

6

16

16

21

25

23

24

3013

32

9

34

10

9a

31

11

29

11

20

1519

41

35

131111

3

25

24

23

11 11

33

128

36

25

24

23

30

21

15 16 15 35

35 13

2524

23

35

9b

9c

9d

9

42

39

20

29

29

10a

43

44

45

46

ITEM: PART No: Description Comments: QTY.

1 206713 80MM DIAMETER BLACK WHEEL 2

2 304356 FLOOR TOOL PIVOT TUBE 1

3 206964 SLIDE NYLON SPACER 4

4 206954 SPIRO SPACER 2

5 291125 M6 X 40 LONG HEX BOLT STAINLESS STEEL 1

6 219642 M6 STAINLESS STEEL NYLON INSERT NUT 2

7 304359 TT/TTB/4045/4055 SQUEEGEE MOUNT WELD ASSEMBLY 1

9 208888 EXTENDED STRAINER 1

9a 208890 EXTENDED STRAINER CLEAR BOWL 1

9b 208830 STRAINER GASKET 1

9c 208889 EXTENDED STRAINER 50 MESH SCREEN 1

9d 208827 STRAINER BLACK TOP 1

9 901543 12MM SWIVEL ELBOW PUSH FIT TO 10MM HOSE TAIL BALL VALVE ASSEMBLY 1

10a 901544 TAP HANDLE C/W COVER AND M3X6MM SCREW (SPARE ITEM) SPARE ITEM 1

10 304453 NUTSERTED 10MM TAP BRACKET 1

11 208312 IGUS BEARING (GFM 101205) 6

12 208574 M8 X 10 X 60 SHOULDER BOLT 1

13 237632 SHOULDER BOLT COVER 3

14 219631 19MM GROMMET 1

15 219578 M8 FORM A STAINLESS STEEL WASHER 4

16 219639 M8 STAINLESS STEEL NYLON INSERT NUT 3

17 208771 TPR OPEN GROMMET 1

18 304358 DECK LOCK BAR WELD ASSEMBLY 1

19 208578 DECK LOCK SPRING 1

20 219547 M5 X 16MM LONG POZI PAN STAINLESS STEEL SCREW 4

21 208638 160mm WHEEL WITH POLYURETHENE TYRE 2

22 321902 SILENCER CLAMP 1

23 219719 M6 X 16MM LONG HEXAGONAL STAINLESS STEEL HEAD BOLT 5

24 219718 M6 STAINLESS STEEL SPRING WASHER 5

25 219647 M6 FORM G STAINLESS STEEL WASHER 5

26 219897 M10 STAINLESS STEEL NYLON INSERT NUT 2

27 391440 1/2 INCH X 18G X 41MM LONG STAINLESS STEEL SPACER TUBE 2

28 219894 M10 X 60MM LONG HEXAGONAL STAINLESS STEEL BOLT 2

29 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 4

30 291057 M8 X 10 X 55MM LONG HEX SOCKET SHOULDER BOLT 2

31 391216 SILICON TUBE 8MM I/D X 3.2MM WALL SECTION (CUT 600MM) 1

32 901555 NYLON TUBE 12MM OD X 10MM ID (110MM) 1

33 208619 FLOOR TOOL SPRING 1

34 391215 SILICON TUBE 200MM LONG X 8MM I/D X 3.2MM WALL SECTION 1

35 219903 M10 FORM A STAINLESS STEEL WASHER 4

36 900213 TT/4045/4055 CHASSIS WELD ASSY (12SWG S/S) (2014 MODEL) 1

37 219558 M5 STAINLESS STEEL NUTSERT 4

38 291167 M6 X 70MM LONG HEX BOLT 1

39 901279 LATCH BLOCK TOP MOULDING 1

40 901280 LATCH BLOCK BOTTOM MOULDING 1

41 901558 M5 X 65MM STAINLESS STEEL POZI PAN MACHINE SCREW 3

42 219633 M5 STAINLESS STEEL NYLON INSERT NUT 3

43 901006 FILTER MOUNTING BRACKET 1

44 219644 M5 FORM G STAINLESS STEEL WASHER 2

45 219861 M5 SINGLE COIL STAINLESS STEEL WASHER 2

46 219571 M5 X 20MM LONG POZI PAN STAINLESS STEEL SCREW 2

Numatic International Spare PartsModel No:

DRAWING: DRW-16813 ISS:A06Numatic International Spare PartsModel No:26/10/2015TT4045 (TT1117) & TT4055 (TT1120) CHASSIS ASSEMBLY TT4045 (TT1117) & TT4055 (TT1120) CHASSIS ASSEMBLY

244496Internal Code:

PRO

19

20

22

21

23

18

15

25

23416

31 301 29

13534

7

2

16

6

17

17

24

28

26

27

3314

35

10

37

11

9a

34

8

12

32

32

12

23

16

23

32

38

141212

3

28

27

26

12 12

36

131

39

28

27

26

33

24

16 17 16 38

38 14

2827

26

38

9b

9c

9d

9

3223

23

32

32

23

10a

ITEM: PART No: Description Comments: QTY.

1 206713 80MM DIAMETER BLACK WHEEL 2

2 304356 FLOOR TOOL PIVOT TUBE 1

3 206964 SLIDE NYLON SPACER 4

4 206954 SPIRO SPACER 2

5 291125 M6 X 40 LONG HEX BOLT STAINLESS STEEL 1

6 219642 M6 STAINLESS STEEL NYLON INSERT NUT 2

7 304359 TT/TTB/4045/4055 SQUEEGEE MOUNT WELD ASSEMBLY 1

8 392199 FILTER BRACKET 1

9 208888 EXTENDED STRAINER 1

9a 208890 EXTENDED STRAINER CLEAR BOWL 1

9b 208830 STRAINER GASKET 1

9c 208889 EXTENDED STRAINER 50 MESH SCREEN 1

9d 208827 STRAINER BLACK TOP 1

10 901543 12MM SWIVEL ELBOW PUSH FIT TO 10MM HOSE TAIL BALL VALVE ASSEMBLY 1

10a 901544 TAP HANDLE C/W COVER AND M3X6MM SCREW (SPARE ITEM) SPARE ITEM 1

11 304453 NUTSERTED 10MM TAP BRACKET 1

12 208312 IGUS BEARING (GFM 101205) 6

13 208574 M8 X 10 X 60 SHOULDER BOLT 1

14 237632 SHOULDER BOLT COVER 3

15 219631 19MM GROMMET 1

16 219578 M8 FORM A STAINLESS STEEL WASHER 4

17 219639 M8 STAINLESS STEEL NYLON INSERT NUT 3

18 208771 TPR OPEN GROMMET 1

19 304411 NUTSERTED LOCK BAR CLAMP 1

20 304409 NUTSERTED DECK LOCK BAR GUIDE 1

21 304358 DECK LOCK BAR WELD ASSEMBLY 1

22 208578 DECK LOCK SPRING 1

23 219547 M5 X 16MM LONG POZI PAN STAINLESS STEEL SCREW 12

24 208638 160MM DIAMETER WHEEL / POLYURETHANE TYRE 2

25 321902 SILENCER CLAMP 1

26 219719 M6 X 16MM LONG HEXAGONAL STAINLESS STEEL HEAD BOLT 5

27 219718 M6 STAINLESS STEEL SPRING WASHER 5

28 219647 M6 FORM G STAINLESS STEEL WASHER 5

29 219897 M10 STAINLESS STEEL NYLON INSERT NUT 2

30 391440 1/2 INCH X 18G X 41MM LONG STAINLESS STEEL SPACER TUBE 2

31 219894 M10 X 60MM LONG HEXAGONAL STAINLESS STEEL BOLT 2

32 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 12

33 291057 M8 X 10 X 55MM LONG HEX SOCKET SHOULDER BOLT 2

34 391216 SILICON TUBE 8MM I/D X 3.2MM WALL SECTION (CUT 600MM) 1

35 901555 NYLON TUBE 12MM OD X 10MM ID (110MM) 1

36 208619 FLOOR TOOL SPRING 1

37 391215 SILICON TUBE 200MM LONG X 8MM I/D X 3.2MM WALL SECTION 1

38 219903 M10 FORM A STAINLESS STEEL WASHER 4

39 900213 TT/4045/4055 CHASSIS WELD ASSY (12SWG S/S) 1

40 219558 M5 STAINLESS STEEL NUTSERT 4

41 291167 M6 X 70MM LONG HEX BOLT 1

Numatic International Spare PartsModel No:

DRAWING: DRW-16813 ISS:A04Numatic International Spare PartsModel No:29/06/2015TT4045 (TT1117) & TT4055 (TT1120) CHASSIS ASSEMBLY TT4045 (TT1117) & TT4055 (TT1120) CHASSIS ASSEMBLY

244496Internal Code:

PRO

1

5

19

13

13

7

12

1414

111518

6

20

34

2

1316

13

9

14 14

18 15 10 17

23

22

8

21

24

ITEM: PART No: Description Comments: QTY.

1 237656 TT.4055 TOP TANK MOULDING (BLUE) 1

237731 TT.4055 TOP TANK MOULDING (RED) 1

237733 TT.4055 TOP TANK MOULDING (LIGHT YELLOW) 1

237735 TT.4055 TOP TANK MOULDING (GREEN) 1

2 237382 ACETAL HOSE CLIP MOULDING 1

3 219668 M5 X 10MM LONG POZI PAN STAINLESS STEEL SCREW 2

4 219016 M5 SHAKEPROOF WASHER 2

5 207000 GRIT FILTER BASKET 1

6 206209 A.B.A HOSE CLIP 1

7 237381 INTEGRATED CHASSIS SEPARATOR 1

8 392200 FILTER GASKET RING 1

9 237090 SEPARATOR FLOAT MOULDING (MK 2) 1

10 237526 38MM RED DRAIN HOSE CONNECTOR 1

11 237018 38MM DRAIN HOSE CONNECTOR 1

12 229494 CLIP MOULDING 2

13 219852 NO6 X 1/2 LONG POZI PAN STAINLESS STEEL SELF TAP SCREW 4

14 219569 No8 X 1/2 INCH LONG POZI PAN STAINLESS STEEL PLASTITE SCREW 4

15 219310 RUBBER WASHER 2

16 206315 TUBE END PLUG 3

17 206265 TT/B 345 BARREL FILTER 1

18 206116 BLACK NUT 2

19 208591 NEW SEPARATOR GASKET 1

20 280018 35MM X 435MM LONG 3:1 STRETCH HOSE C/W CAP & STRAP(SHORT CUFF) 1

21 900903 HOSE CLOSURE REPLACEMENT KIT (35MM-38MM STRETCH HOSE)

22 213058 VAC HOSE 650MM X Ø38MM 1

23 280019 35MM X 690MM LONG 3:1 STRETCH HOSE (SHORT & LONG CUFF) 1

24 237718 HOSE GUIDE 1

Numatic International Spare PartsModel No:

DRAWING: DRW-16795 ISS:A04Numatic International Spare PartsModel No:18/02/2015

NB: FOR WIRING SEE DRAWING: N/ATT4045 (TT1117) & TT4055 (TT1120) TOP TANK ASSEMBLY TT4045 (TT1117) & TT4055 (TT1120) TOP TANK ASSEMBLY

244498

20

33

21

19

24

31

3834

2730

29

50

28

22

26

45

51

32

48

18

78

70

47

59

53

58

57

69

54

5556

366 6577

4

5

2

6

1 7

72

23

73

67

61 46

41

3712 1736

43

42

606263

13

64

5239

15

16

14 35

44

49

71

10

9

25

11

55

55

8

69

40

377

75

76

38

71

49 43

38

43

4545

50

36

43

45

41

18

79

40

68

75

76

74

48 38

45

80

23

ITEM: PART No: Description Comments: QTY.1 229081 HANDLE CASTING MACHINED 12 229074 ADJUSTMENT GEAR 13 219254 O RING 3MM DIA X 60MM I/D 24 229073 GEAR LOCKING PIN 15 229138 SPRING 16 219099 M6 HALF NUT 17 229099 25MM DIA HOLE PLUG 18 219010 M8 FORM A WASHER 19 338269 CROSS TUBE 110 227576 FRONT INNER HALF MOULDING 1

229508 FLAME RETARDANT FRONT INNER HALF MOULDING FLAME RETARDANT CSA SPEC 111 227577 REAR INNER HALF MOULDING 1

329484 MODIFIED REAR INNER HALF MOULDING (CSA SPEC) FLAME RETARDANT CSA SPEC 112 303526 NUTSERTED RELAY MOUNTING BRACKET 113 229748 FRONT COVER MOULDING (MAINS & BATTERY) 1

229750 MAINS FRONT COVER MOULDING (C/B HOLE) 110V/50HZ MACHINES 1229751 MAINS FRONT COVER MOULDING (C/B HOLE)(FLAME RETARDANT) 120V/60HZ FLAME RETARDENT MACHINES 1

14 220812 230V NEON INDICATOR & RED LENS 1220813 120V NEON INDICATOR & RED LENS 1

15 227585 LEFT HAND SWITCH OPERATING LEVER MOULDING 116 227586 RIGHT HAND SWITCH OPERATING LEVER MOULDING 117 227587 CENTRE SWITCH OPERATING LEVER MOULDING 118 227580 HAND GRIP MOULDING 219 227583 ADJUSTMENT LEVER MOULDING 120 219493 M6 NYLON WASHER 121 219088 M6 NYLON INSERT NUT 122 227676 REAR COVER 1

229507 MAINS TYPE FLAME RETARDANT REAR COVER MOULDING FLAME RETARDANT CSA SPEC 123 229009 BLANKING PLUG 224 227584 INTERLOCK LEVER MOULDING 125 227582 HANDLE PLUG MOULDING 126 227691 TERMINAL BLOCK 1

229510 FLAME RETARDANT TERMINAL BLOCK FLAME RETARDANT CSA SPEC 127 227680 TERMINAL BLOCK COVER 1

229511 FLAME RETARDANT TERMINAL BLOCK COVER FLAME RETARDANT CSA SPEC 128 206562 CONTACT PIN 229 206563 EARTH CONTACT PIN 130 219090 M4 X 8MM LONG POZI PAN SEMS SCREW 331 227678 SOCKET COVER 1

229512 FLAME RETARDANT INLET COVER FLAME RETARDANT CSA SPEC 132 227008 BLACK CABLE CLAMP 233 20638V 19MM BLACK TUBE END STOP 134 216290 CABLE CLAMP 135 206575 240V / 25A RELAY 1

206576 100V-120V / 25A RELAY 136 229483 SNAP ACTION SWITCH 237 219805 4MM SPIREFIX 138 219107 No6 X 5/8 INCH LONG POZI PAN PLASTITE SCREW 839 219471 M4 X 12MM LONG POZI PAN SEMS SCREW 240 219560 M6 FORM B STAINLESS STEEL WASHER 641 219803 TRIGGER COMPRESSION SPRING 242 219804 SWITCH COMPRESSION SPRING 143 219569 No8 X 1/2 INCH LONG POZI PAN STAINLESS STEEL PLASTITE SCREW 1044 219811 NO8 X 1 INCH LONG POZI-PAN SELF TAP SCREW 245 219105 No8 X 5/8 INCH LONG POZI PAN PLASTITE SCREW 846 226008 STRESS RELIEF 147 329231 STRESS RELIEF BRACKET 148 219206 M4 FORM A WASHER 249 219270 No8 X 1/2 INCH LONG POZI PAN SELF TAP SCREW 250 219568 No8 X 3/4 INCH LONG POZI PAN STAINLESS STEEL SCREW 351 219005 M5 FORM G WASHER 152 270146 GREEN ILLUMINATED SWITCH + MEMBRANE 253 236012 20.0M X 1.50MM X 3 CORE NUCABLE (UK PLUG) 1

236132 20M X 1.5MM X 3 CORE YELLOW CABLE X SOCKET (EURO PLUG) 1236020 20.0M X 1.5MM X 3 CORE NUCABLE (SWISS PLUG) 1236024 20.0M X 1.50MM X 3 CORE NUCABLE (SOUTH AFRICAN PLUG) 1236068 20.0MT X 1.5MM X 3 CORE CABLE (16A SOCKET + 10A PLUG) AUSTRALIAN 1236118 20.0M X 1.5MM X 3 CORE NUCABLE (16 AMP INDUSTRIAL PLUG) 1236028 20.0M X 14AWG X 3 CORE YELLOW NUCABLE (CSA PLUG) 1

54 227806 CABLE RELEASE BASE MOULDING 155 219644 M5 FORM G STAINLESS STEEL WASHER 356 219076 M5 NYLON INSERT NUT 157 227807 CABLE RELEASE TOP MOULDING 158 206599 SPRING (REF:C5514370) 159 219720 M5 X 30MM LONG STAINLESS STEEL POZI PAN SCREW 160 206500 RELAY BRACKET 161 226006 SPACER (BLACK) 162 220440 8 AMP OVERLOAD 120V/60HZ FLAME RETARDENT MACHINES 1

208550 15 AMP OVERLOAD 110V/50HZ MACHINES 163 219702 M10 INTERNAL LOCK WASHER 110V & 120V MACHINES 164 220459 OVERLOAD DUST COVER 110V & 120V MACHINES 165 219632 M8 STAINLESS STEEL DOME NUT 366 219018 M8 SHAKEPROOF WASHER 367 219922 M8 X 50MM LONG SOCKET BUTTON HEAD STAINLESS STEEL BOLT 368 291125 M6 X 40 LONG HEX BOLT STAINLESS STEEL 269 219764 M6 STAINLESS STEEL DOME NUT 470 229461 440MM HANDLE LOCKING ROD 171 229500 TRIGGER MOULDING BLUE 272 330231 TTB/TT 430MM PROCESSED ALI HANDLE PAINT GREY 173 237692 HANDLE CABLE COVER L/H 174 237693 HANDLE CABLE COVER R/H 175 219740 M5 X 12MM LONG STAINLESS STEEL POZI PAN SCREW 276 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 277 219578 M8 FORM A STAINLESS STEEL WASHER 678 219546 M5 X 20MM LONG POZI PAN SEMS SCREW 179 291128 M6 X 50 LONG HEX BOLT STAINLESS STEEL 280 392437 RETAINER SPACER 281 219718 M6 STAINLESS STEEL SPRING WASHER 4

Numatic International Spare PartsModel No:

DRAWING: DRW-16831 ISS:A01Numatic International Spare PartsModel No:05/11/2014

NB: FOR WIRING SEE DRAWING: DRW-17307, DRW-17309, DRW-17314TT4045 (TT1117) & TT4055 (TT1120) HANDLE ASSEMBLY TT4045 (TT1117) & TT4055 (TT1120) HANDLE ASSEMBLY

244495

20

33

21

19

24

31

3834

2730

29

50

28

22

26

45

51

32

48

18

78

70

47

59

53

58

57

8354

5556

366 6577

4

5

2

6

1 7

72

23

73

67

61 46

41

3712 1736

43

42

606263

13

64

5239

15

16

14 35

44

49

71

10

9

25

11

55

55

8

69

40

3

77

75

76

38

71

49 43

38

43

4545

50

36

43

4541

18

79

82

68

75

76

74

48 38

45

80

23

81

ITEM: PART No: Description Comments: QTY.1 229081 HANDLE CASTING MACHINED 12 229074 ADJUSTMENT GEAR 13 219254 O RING 3MM DIA X 60MM I/D 24 229073 GEAR LOCKING PIN 15 229138 SPRING 16 219099 M6 HALF NUT 17 229099 25MM DIA HOLE PLUG 18 219010 M8 FORM A WASHER 19 338269 CROSS TUBE 1

10 227576 FRONT INNER HALF MOULDING 1229508 FLAME RETARDANT FRONT INNER HALF MOULDING FLAME RETARDANT CSA SPEC 1

11 227577 REAR INNER HALF MOULDING 1329484 MODIFIED REAR INNER HALF MOULDING (CSA SPEC) FLAME RETARDANT CSA SPEC 1

12 303526 NUTSERTED RELAY MOUNTING BRACKET 113 229748 FRONT COVER MOULDING (MAINS & BATTERY) 1

229750 MAINS FRONT COVER MOULDING (C/B HOLE) 110V/50HZ MACHINES 1229751 MAINS FRONT COVER MOULDING (C/B HOLE)(FLAME RETARDANT) 120V/60HZ FLAME RETARDENT MACHINES 1

14 220812 230V NEON INDICATOR & RED LENS 1220813 120V NEON INDICATOR & RED LENS 1

15 227585 LEFT HAND SWITCH OPERATING LEVER MOULDING 116 227586 RIGHT HAND SWITCH OPERATING LEVER MOULDING 117 227587 CENTRE SWITCH OPERATING LEVER MOULDING 118 227580 HAND GRIP MOULDING 219 227583 ADJUSTMENT LEVER MOULDING 120 219493 M6 NYLON WASHER 121 219088 M6 NYLON INSERT NUT 122 227676 REAR COVER 1

229507 MAINS TYPE FLAME RETARDANT REAR COVER MOULDING FLAME RETARDANT CSA SPEC 123 229009 BLANKING PLUG 224 227584 INTERLOCK LEVER MOULDING 125 227582 HANDLE PLUG MOULDING 126 227691 TERMINAL BLOCK 1

229510 FLAME RETARDANT TERMINAL BLOCK FLAME RETARDANT CSA SPEC 127 227680 TERMINAL BLOCK COVER 1

229511 FLAME RETARDANT TERMINAL BLOCK COVER FLAME RETARDANT CSA SPEC 128 206562 CONTACT PIN 229 206563 EARTH CONTACT PIN 130 219090 M4 X 8MM LONG POZI PAN SEMS SCREW 331 227678 SOCKET COVER 1

229512 FLAME RETARDANT INLET COVER FLAME RETARDANT CSA SPEC 132 227008 BLACK CABLE CLAMP 233 20638V 19MM BLACK TUBE END STOP 134 216290 CABLE CLAMP 135 206575 240V / 25A RELAY 1

206576 100V-120V / 25A RELAY 136 229483 SNAP ACTION SWITCH 237 219805 4MM SPIREFIX 138 219107 No6 X 5/8 INCH LONG POZI PAN PLASTITE SCREW 839 219471 M4 X 12MM LONG POZI PAN SEMS SCREW 240 219560 M6 FORM B STAINLESS STEEL WASHER 241 219803 TRIGGER COMPRESSION SPRING 242 219804 SWITCH COMPRESSION SPRING 143 219569 No8 X 1/2 INCH LONG POZI PAN STAINLESS STEEL PLASTITE SCREW 1044 219811 NO8 X 1 INCH LONG POZI-PAN SELF TAP SCREW 245 219105 No8 X 5/8 INCH LONG POZI PAN PLASTITE SCREW 846 226008 STRESS RELIEF 147 329231 STRESS RELIEF BRACKET 148 219206 M4 FORM A WASHER 249 219270 No8 X 1/2 INCH LONG POZI PAN SELF TAP SCREW 250 219568 No8 X 3/4 INCH LONG POZI PAN STAINLESS STEEL SCREW 351 219005 M5 FORM G WASHER 152 270146 GREEN ILLUMINATED SWITCH + MEMBRANE 253 236012 20.0M X 1.50MM X 3 CORE NUCABLE (UK PLUG) 1

236132 20M X 1.5MM X 3 CORE YELLOW CABLE X SOCKET (EURO PLUG) 1236020 20.0M X 1.5MM X 3 CORE NUCABLE (SWISS PLUG) 1236024 20.0M X 1.50MM X 3 CORE NUCABLE (SOUTH AFRICAN PLUG) 1236068 20.0MT X 1.5MM X 3 CORE CABLE (16A SOCKET + 10A PLUG) AUSTRALIAN 1236118 20.0M X 1.5MM X 3 CORE NUCABLE (16 AMP INDUSTRIAL PLUG) 1236028 20.0M X 14AWG X 3 CORE YELLOW NUCABLE (CSA PLUG) 1

54 227806 CABLE RELEASE BASE MOULDING 155 219644 M5 FORM G STAINLESS STEEL WASHER 356 219076 M5 NYLON INSERT NUT 157 227807 CABLE RELEASE TOP MOULDING 158 206599 SPRING (REF:C5514370) 159 219720 M5 X 30MM LONG STAINLESS STEEL POZI PAN SCREW 160 206500 RELAY BRACKET 161 226006 SPACER (BLACK) 162 220440 8 AMP OVERLOAD 120V/60HZ FLAME RETARDENT MACHINES 1

208550 15 AMP OVERLOAD 110V/50HZ MACHINES 163 219702 M10 INTERNAL LOCK WASHER 110V & 120V MACHINES 164 220459 OVERLOAD DUST COVER 110V & 120V MACHINES 165 219632 M8 STAINLESS STEEL DOME NUT 366 219018 M8 SHAKEPROOF WASHER 367 219922 M8 X 50MM LONG SOCKET BUTTON HEAD STAINLESS STEEL BOLT 368 291125 M6 X 40 LONG HEX BOLT STAINLESS STEEL 269 219764 M6 STAINLESS STEEL DOME NUT 270 229461 440MM HANDLE LOCKING ROD 171 229500 TRIGGER MOULDING BLUE 2

227581 TRIGGER MOULDING (GREY) 272 330231 TTB/TT 430MM PROCESSED ALI HANDLE PAINT GREY 173 237692 HANDLE CABLE COVER L/H 174 237693 HANDLE CABLE COVER R/H 175 219740 M5 X 12MM LONG STAINLESS STEEL POZI PAN SCREW 276 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 277 219578 M8 FORM A STAINLESS STEEL WASHER 678 219546 M5 X 20MM LONG POZI PAN SEMS SCREW 179 291128 M6 X 50 LONG HEX BOLT STAINLESS STEEL 280 392437 RETAINER SPACER 281 219718 M6 STAINLESS STEEL SPRING WASHER 282 219544 M6 SHAKEPROOF WASHER 483 219642 M6 STAINLESS STEEL NYLON INSERT NUT 2

Numatic International Spare PartsModel No:

DRAWING: DRW-16831 ISS:A04Numatic International Spare PartsModel No:05/05/2015

NB: FOR WIRING SEE DRAWING: DRW-18548, DRW-17307, DRW-17309, DRW-18468TT4045 (TT1117) & TT4055 (TT1120) HANDLE ASSEMBLY TT4045 (TT1117) & TT4055 (TT1120) HANDLE ASSEMBLY

244495

48

20 45

41 46

2728 44

31 42

19

35

34

2

36

37

1

18

17

141516

3

3029

6

2625

23

24

4225

13

3378932311011

31

31

43

6

19

12

2

21 12 12

21

42 43 42

474247

47

38

41

39 39

21

21

2131

21 31

21

ITEM: PART No: Description Comments: QTY.

1 237657 TT.4055 BOTTOM TANK MOULDING (GRAPHITE) 1

237689 TT.4055 BOTTOM TANK MOULDING (GRAPHITE) EP 1

2 206111 HOSE CLOSURE 2

3 202008 MOTOR CAP GASKET 1

4 304417 MAINS MOTOR MOUNT WELD ASSEMBLY 1

5 205443 230V 2 STAGE D.I BYPASS ACUSTEK MOTOR (BL21104T) (MARKED 230V) TCO 1

321935 120V VAC MOTOR ASSEMBLY C/W 170MM LONG MOTOR LEAD 1

6 219569 No8 X 1/2 INCH LONG POZI PAN STAINLESS STEEL PLASTITE SCREW 4

7 219310 RUBBER WASHER 1

8 212052 3MM THICK X 9MM WIDE INSEAL (700MM LONG) 1

9 392441 TT4045/55 VAC MOTOR BACK PLATE 1

10 237526 38MM RED DRAIN HOSE CONNECTOR 1

11 206116 BLACK NUT 1

12 237382 ACETAL HOSE CLIP MOULDING 3

13 213025 600MM - 630MM LONG DUMP HOSE ASSEMBLY 1

14 208956 SILENCER FOAM TUBE 150MM 1

15 208583 DIP MOULDED ELBOW (MAINS VERSION) 1

16 208471 CONSTANT TENSION CLIP 1

17 206818 HOSE CLIP 1

18 208957 3/8" SWIVEL MALE 90 DEG ELBOW 1

19 219668 M5 X 10MM LONG POZI PAN STAINLESS STEEL SCREW 4

20 237691 SQUEEGEE LIFT HANDLE 1

21 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 11

22 208801 TT MOTOR GASKET 1

23 208799 TT MOTOR PLATE GASKET 1

24 219740 M5 X 12MM LONG STAINLESS STEEL POZI PAN SCREW 4

25 219861 M5 SINGLE COIL STAINLESS STEEL WASHER 4

26 219355 M5 FORM A STAINLESS STEEL WASHER 4

27 291118 M5 STAINLESS STEEL WASHER 19MM OD 1

28 208962 TT LIFTING WIRE 1

29 219721 M5 STAINLESS STEEL FULL NUT 1

30 219633 M5 STAINLESS STEEL NYLON INSERT NUT 1

31 219547 M5 X 16MM LONG POZI PAN STAINLESS STEEL SCREW 11

32 219644 M5 FORM G STAINLESS STEEL WASHER 4

33 202069 BOTTOM MOTOR GASKET 1

34 207128 CLEAN TANK INLET FILTER 1

35 237268 FILLER CAP LID 1

36 208960 TTB/TT FILLING HOSE 1

37 220403 CABLE CLIP 2

38 404216 HANDLE MOUNT WELD ASSEMBLY - Z/PL 1

39 392445 HANDLE MOUNT COVER PAINT GREY 2

40 219558 M5 STAINLESS STEEL NUTSERT 7

41 291124 M10 PENNY WASHER STAINLESS STEEL 2

42 219716 M8 FORM G STAINLESS STEEL WASHER 8

43 219639 M8 STAINLESS STEEL NYLON INSERT NUT 4

44 219686 M4 X 20MM LONG STAINLESS STEEL POZI PAN MACHINE SCREW 1

45 219687 M4 STAINLESS STEEL NYLON INSERT NUT 1

46 219895 M10 X 35MM LONG HEXAGONAL STAINLESS STEEL SCREW 1

47 291123 M8 X 75 LONG HEX HEAD BOLT STAINLESS STEEL 4

48 219897 M10 STAINLESS STEEL NYLON INSERT NUT 1

Numatic International Spare PartsModel No:

DRAWING: DRW-16829 ISS:A02Numatic International Spare PartsModel No:19/01/2015

NB: FOR WIRING SEE DRAWING: DRW-18548, DRW-17307, DRW-17309, DRW-18468

TT4045 (TT1117) & TTB4055 (TT1120) BOTTOM TANK / VAC MOTOR ASSEMBLY

TT4045 (TT1117) & TTB4055 (TT1120) BOTTOM TANK / VAC MOTOR ASSEMBLY

244497

48

20 45

41 46

2728 44

31 42

19

35

34

2

36

37

1

18

17

141516

3

3029

6

2625

23

24

4225

13

3378932311011

31

31

43

6

19

12

2

21 12 12

21

42 43 42

474247

47

38

41

39 39

21

21

2131

21 31

21

ITEM: PART No: Description Comments: QTY.

1 237657 TT.4055 BOTTOM TANK MOULDING (GRAPHITE) 1

237689 TT.4055 BOTTOM TANK MOULDING (GRAPHITE) EP 1

2 206111 HOSE CLOSURE 2

3 202008 MOTOR CAP GASKET 1

4 404143 TT/4045/4055 VAC MOTOR MOUNTING PLATE - PAINT GREY 1

5 205443 230V 2 STAGE D.I BYPASS ACUSTEK MOTOR (BL21104T) (MARKED 230V) TCO 1

321935 120V VAC MOTOR ASSEMBLY C/W 170MM LONG MOTOR LEAD 1

6 219569 No8 X 1/2 INCH LONG POZI PAN STAINLESS STEEL PLASTITE SCREW 4

7 219310 RUBBER WASHER 1

8 212052 3MM THICK X 9MM WIDE INSEAL (700MM LONG) 1

9 392441 TT4045/55 VAC MOTOR BACK PLATE 1

10 237526 38MM RED DRAIN HOSE CONNECTOR 1

11 206116 BLACK NUT 1

12 237382 ACETAL HOSE CLIP MOULDING 3

13 213025 600MM - 630MM LONG DUMP HOSE ASSEMBLY 1

14 208956 SILENCER FOAM TUBE 150MM 1

15 208583 DIP MOULDED ELBOW (MAINS VERSION) 1

16 208471 CONSTANT TENSION CLIP 1

17 206818 HOSE CLIP 1

18 208957 3/8" SWIVEL MALE 90 DEG ELBOW 1

19 219668 M5 X 10MM LONG POZI PAN STAINLESS STEEL SCREW 4

20 237691 SQUEEGEE LIFT HANDLE 1

21 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 11

22 208801 TT MOTOR GASKET 1

23 208799 TT MOTOR PLATE GASKET 1

24 219740 M5 X 12MM LONG STAINLESS STEEL POZI PAN SCREW 4

25 219861 M5 SINGLE COIL STAINLESS STEEL WASHER 4

26 219355 M5 FORM A STAINLESS STEEL WASHER 4

27 291118 M5 STAINLESS STEEL WASHER 19MM OD 1

28 208962 TT LIFTING WIRE 1

29 219721 M5 STAINLESS STEEL FULL NUT 1

30 219633 M5 STAINLESS STEEL NYLON INSERT NUT 1

31 219547 M5 X 16MM LONG POZI PAN STAINLESS STEEL SCREW 11

32 219644 M5 FORM G STAINLESS STEEL WASHER 4

33 202069 BOTTOM MOTOR GASKET 1

34 207128 CLEAN TANK INLET FILTER 1

35 237268 FILLER CAP LID 1

36 208960 TTB/TT FILLING HOSE 1

37 220403 CABLE CLIP 2

38 404216 HANDLE MOUNT WELD ASSEMBLY - Z/PL 1

39 392445 HANDLE MOUNT COVER PAINT GREY 2

40 219558 M5 STAINLESS STEEL NUTSERT 7

41 291124 M10 PENNY WASHER STAINLESS STEEL 2

42 219716 M8 FORM G STAINLESS STEEL WASHER 8

43 219639 M8 STAINLESS STEEL NYLON INSERT NUT 4

44 219686 M4 X 20MM LONG STAINLESS STEEL POZI PAN MACHINE SCREW 1

45 219687 M4 STAINLESS STEEL NYLON INSERT NUT 1

46 219895 M10 X 35MM LONG HEXAGONAL STAINLESS STEEL SCREW 1

47 291123 M8 X 75 LONG HEX HEAD BOLT STAINLESS STEEL 4

48 219897 M10 STAINLESS STEEL NYLON INSERT NUT 1

Numatic International Spare PartsModel No:

DRAWING: DRW-16829 ISS:A01Numatic International Spare PartsModel No:05/11/2014

NB: FOR WIRING SEE DRAWING: DRW-17307, DRW-17309, DRW-17314

TT4045 (TT1117) & TTB4055 (TT1120) BOTTOM TANK / VAC MOTOR ASSEMBLY

TT4045 (TT1117) & TTB4055 (TT1120) BOTTOM TANK / VAC MOTOR ASSEMBLY

244497

1

5

19

13

13

7

12

1414

111518

6

20

34

2

1316

13

9

14 14

18 15 10 17

21

22

8

ITEM: PART No: Description Comments: QTY.

1 237656 TT.4055 TOP TANK MOULDING (BLUE) 12 237382 ACETAL HOSE CLIP MOULDING 13 219668 M5 X 10MM LONG POZI PAN STAINLESS STEEL SCREW 24 219016 M5 SHAKEPROOF WASHER 25 207000 GRIT FILTER BASKET 16 206209 A.B.A HOSE CLIP 17 237381 INTEGRATED CHASSIS SEPARATOR 18 392200 FILTER GASKET RING 19 237090 SEPARATOR FLOAT MOULDING (MK 2) 110 237526 38MM RED DRAIN HOSE CONNECTOR 111 237018 38MM DRAIN HOSE CONNECTOR 112 229494 CLIP MOULDING 213 219852 NO6 X 1/2 LONG POZI PAN STAINLESS STEEL SELF TAP SCREW 414 219569 No8 X 1/2 INCH LONG POZI PAN STAINLESS STEEL PLASTITE SCREW 415 219310 RUBBER WASHER 216 206315 TUBE END PLUG 317 206265 TT/B 345 BARREL FILTER 118 206116 BLACK NUT 219 208591 NEW SEPARATOR GASKET 120 213047 38MM X 470MM LONG 3:1 STRETCH HOSE C/W CAP & STRAP 121 208624 TT/TTB4045/4055 STRETCH HOSE 122 208588 TT/TTB4045/4055 VAC HOSE 1

Numatic International Spare PartsModel No:

DRAWING: DRW-16795 ISS:A01Numatic International Spare PartsModel No:05/11/2014

NB: FOR WIRING SEE DRAWING: N/ATT4045 (TT1117) & TT4055 (TT1120) TOP TANK ASSEMBLY TT4045 (TT1117) & TT4055 (TT1120) TOP TANK ASSEMBLY

244498

19

20

22

21

23

18

15

25

23416

31 301 29

13534

7

2

16

6

17

17

24

28

26

27

3314

3510

37

119a

34

8

12

32

32

12

23

16

23

32

38

141212

3

28

27

26

12 12

36

131

39

28

27

26

33

24

16 17 16 38

38 14

2827

26

38

9b

9c

9d

9

3223

23

32

32

23

ITEM: PART No: Description Comments: QTY.

1 206713 80MM DIAMETER BLACK WHEEL 2

2 304356 FLOOR TOOL PIVOT TUBE 1

3 206964 SLIDE NYLON SPACER 4

4 206954 SPIRO SPACER 2

5 291125 M6 X 40 LONG HEX BOLT STAINLESS STEEL 1

6 219642 M6 STAINLESS STEEL NYLON INSERT NUT 2

7 304359 TT/TTB/4045/4055 SQUEEGEE MOUNT WELD ASSEMBLY 1

8 392199 FILTER BRACKET 1

9 208888 EXTENDED STRAINER 1

9a 208890 EXTENDED STRAINER CLEAR BOWL 1

9b 208830 STRAINER GASKET 1

9c 208889 EXTENDED STRAINER 50 MESH SCREEN 1

9d 208827 STRAINER BLACK TOP 1

10 208958 3/8" BALL VALVE SWIVEL ELBOW TO 10MM HOSETAIL 1

11 304453 NUTSERTED 10MM TAP BRACKET 1

12 208312 IGUS BEARING (GFM 101205) 6

13 208574 M8 X 10 X 60 SHOULDER BOLT 1

14 237632 SHOULDER BOLT COVER 3

15 219631 19MM GROMMET 1

16 219578 M8 FORM A STAINLESS STEEL WASHER 4

17 219639 M8 STAINLESS STEEL NYLON INSERT NUT 3

18 208771 TPR OPEN GROMMET 1

19 304411 NUTSERTED LOCK BAR CLAMP 1

20 304409 NUTSERTED DECK LOCK BAR GUIDE 1

21 304358 DECK LOCK BAR WELD ASSEMBLY 1

22 208578 DECK LOCK SPRING 1

23 219547 M5 X 16MM LONG POZI PAN STAINLESS STEEL SCREW 12

24 208638 160MM DIAMETER WHEEL / POLYURETHANE TYRE 2

25 321902 SILENCER CLAMP 1

26 219719 M6 X 16MM LONG HEXAGONAL STAINLESS STEEL HEAD BOLT 5

27 219718 M6 STAINLESS STEEL SPRING WASHER 5

28 219647 M6 FORM G STAINLESS STEEL WASHER 5

29 219897 M10 STAINLESS STEEL NYLON INSERT NUT 2

30 391440 1/2 INCH X 18G X 41MM LONG STAINLESS STEEL SPACER TUBE 2

31 219894 M10 X 60MM LONG HEXAGONAL STAINLESS STEEL BOLT 2

32 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 12

33 291057 M8 X 10 X 55MM LONG HEX SOCKET SHOULDER BOLT 2

34 391216 SILICON TUBE 8MM I/D X 3.2MM WALL SECTION (CUT 600MM) 1

35 330228 BRAIDED PVC HOSE RP8/13.5 CUT TO LENGTH (85MM) 1

36 208619 FLOOR TOOL SPRING 1

37 391215 SILICON TUBE 200MM LONG X 8MM I/D X 3.2MM WALL SECTION 1

38 219903 M10 FORM A STAINLESS STEEL WASHER 4

39 900213 TT/4045/4055 CHASSIS WELD ASSY (12SWG S/S) 1

40 219558 M5 STAINLESS STEEL NUTSERT 4

41 291167 M6 X 70MM LONG HEX BOLT 1

Numatic International Spare PartsModel No:

DRAWING: DRW-16813 ISS:A02Numatic International Spare PartsModel No:17/02/2015

NB: FOR WIRING SEE DRAWING: WD-0???

TT4045 (TT1117) & TT4055 (TT1120) CHASSIS ASSEMBLY TT4045 (TT1117) & TT4055 (TT1120) CHASSIS ASSEMBLY

244496

19

20

22

21

23

18

15

25

23266

32 311 30

13534

7

2

16

6

17

17

24

29

27

28

3414

3610

38

119a

35

8

12

33

33

12

23

16

23

33

39

141212

3

29

28

27

12 12

37

132

40

29

28

27

34

24

16 17 16 39

39 14

2928

27

39

9b

9c

9d

9

3323

23

33

33

23

ITEM: PART No: Description Comments: QTY.

1 206713 80MM DIAMETER BLACK WHEEL 2

2 304356 FLOOR TOOL PIVOT TUBE 1

3 206964 SLIDE NYLON SPACER 4

4 206954 SPIRO SPACER 2

5 291125 M6 X 40 LONG HEX BOLT STAINLESS STEEL 1

6 219642 M6 STAINLESS STEEL NYLON INSERT NUT 2

7 304359 TT/TTB/4045/4055 SQUEEGEE MOUNT WELD ASSEMBLY 1

8 392199 FILTER BRACKET 1

9 208888 EXTENDED STRAINER 1

9a 208890 EXTENDED STRAINER CLEAR BOWL 1

9b 208830 STRAINER GASKET 1

9c 208889 EXTENDED STRAINER 50 MESH SCREEN 1

9d 208827 STRAINER BLACK TOP 1

10 208958 3/8" BALL VALVE SWIVEL ELBOW TO 10MM HOSETAIL 1

11 304453 NUTSERTED 10MM TAP BRACKET 1

12 208312 IGUS BEARING (GFM 101205) 6

13 208574 M8 X 10 X 60 SHOULDER BOLT 1

14 237632 SHOULDER BOLT COVER 3

15 219631 19MM GROMMET 1

16 219578 M8 FORM A STAINLESS STEEL WASHER 4

17 219639 M8 STAINLESS STEEL NYLON INSERT NUT 3

18 208771 TPR OPEN GROMMET 1

19 304411 NUTSERTED LOCK BAR CLAMP 1

20 304409 NUTSERTED DECK LOCK BAR GUIDE 1

21 304358 DECK LOCK BAR WELD ASSEMBLY 1

22 208578 DECK LOCK SPRING 1

23 219547 M5 X 16MM LONG POZI PAN STAINLESS STEEL SCREW 12

24 208638 160MM DIAMETER WHEEL / POLYURETHANE TYRE 2

25 321902 SILENCER CLAMP 1

26 219521 M6 X 70MM LONG HEX BOLT 1

27 219719 M6 X 16MM LONG HEXAGONAL STAINLESS STEEL HEAD BOLT 5

28 219718 M6 STAINLESS STEEL SPRING WASHER 5

29 219647 M6 FORM G STAINLESS STEEL WASHER 5

30 219897 M10 STAINLESS STEEL NYLON INSERT NUT 2

31 391440 1/2 INCH X 18G X 41MM LONG STAINLESS STEEL SPACER TUBE 2

32 219894 M10 X 60MM LONG HEXAGONAL STAINLESS STEEL BOLT 2

33 291084 WASHER.M5.SHAKEPROOF.STAINLESS STEEL 12

34 291057 M8 X 10 X 55MM LONG HEX SOCKET SHOULDER BOLT 2

35 391216 SILICON TUBE 8MM I/D X 3.2MM WALL SECTION (CUT 600MM) 1

36 330228 BRAIDED PVC HOSE RP8/13.5 CUT TO LENGTH (85MM) 1

37 208619 FLOOR TOOL SPRING 1

38 391215 SILICON TUBE 200MM LONG X 8MM I/D X 3.2MM WALL SECTION 1

39 219903 M10 FORM A STAINLESS STEEL WASHER 4

40 900213 TT/4045/4055 CHASSIS WELD ASSY (12SWG S/S) 1

41 219558 M5 STAINLESS STEEL NUTSERT 4

Numatic International Spare PartsModel No:

DRAWING: DRW-16813 ISS:A01Numatic International Spare PartsModel No:05/11/2014TT4045 (TT1117) & TT4055 (TT1120) CHASSIS ASSEMBLY TT4045 (TT1117) & TT4055 (TT1120) CHASSIS ASSEMBLY

244496