7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 1/20
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 2/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 71
Fig. 4.1. Examples of non-uniform flow
4.1.2. Accelerated and Retarded flow
An idealized section of a reach of a channel with accelerated and retarded flow
conditions is shown in Fig. 4.2a and Fig. 4.2b, respectively. As flow accelerates, with the
rate of flow constant, the depth h must decrease form point 1 to point 2, and a water
surface profile as shown in Fig. 4.2a results. Retarded flow will produce water surface
profiles as shown in Fig. 4.2b.
Significant in each one of the above cases is the fact that now the water surface is a curved
line and not longer parallel to the channel bottom and the energy line, as was the case for
uniform flow. The following points are made in connection with the above observations.
upstream control downstream control
control sluice
gate
rapid
varied
flow
hydraulic jump sharp-crested
weir
rapid
varied
flow
rapid varied
flow
gradually
varied
flow
gradually
varied
flow
upstream control
downstream
control hydraulic
jump
supercritical
flow subcritical
flow
critical
depth
overflow
(critical depth)
control
hc
hc
rapid varied
flow
rapid
varied
flow
rapid
varied
flow
graduallyvaried
flow gradually
varied
flow
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 3/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 72
The water surface, as will be shown later, can have a concave or a convex shape.
The energy line is not necessarily a straight line; however, it is assumed that the
energy gradient is constant along the length of a reach and the energy line will be
represented and considered to have a slope ie = HL /L.
As was done in the case of uniform flow, it is here also accepted that the depth of
flow, h, is equal to the pressure head in the energy equation. Obviously, this applies
only when the slope of the channel bottom is small. For very steep slopes,
allowances for this discrepancy must be made.
i
Lz1 z2
water surface
HL
11
ph
22
ph
2
1V
2 g 2
2V2 g
energy-head line
hydraulic grade line
datum
Fig. 4.2a. Accelerated flow
i
Lz1 z
2
water surface
HL
11
ph
2
2
ph
2
1V
2 g2
2V
2 g
energy-head line
hydraulic grade line
datum
Fig. 4.2b. Retarded flow
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 4/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 73
4.1.3. Equation of non-uniform flow
Fig. 4.3. Non-uniform flow
Consider a non-uniform flow in an open channel between section 1-1 and section 2-2, inwhich the water surface has a rising trend (i.e. the energy-head gradient is less than the bed
slope) as shown in Fig. 4.3.
Let V = velocity of water at section 1-1;
h = depth of water at section 1-1;
V+dV = velocity of water at section 2-2;
h+dh = depth of water at section 2-2;
ib = slope of channel bed;
ie = slope of the energy grade line;
dl = distance between section 1-1 and section 2-2;
b = average width of the channel,Q = discharge through the channel,
zb = change of bottom elevation between section 1-1 and section 2-2, and
he = HL, change of energy grade line between section 1-1 and section 2-2.
Since the depth of water at section 2-2 is larger than at section 1-1, the velocity of water at
section 2-2 will be smaller than that at section 1-1.
Applying Bernoulli’s equation at section 1-1 and section 2-2:
2 2
b e
V (V dV)z h (h dh) h
2g 2g
(4-2)
22
b e
V dVVi .dl h h dh i .dl
2g 2g
(4-3)
b e
V.dVi .dl dh i .dl
g , neglecting
2(dV)
2g(small of second order) (4-4)
or b e
dh V.dVi i
dl g.dl (dividing by dl) (4-5)
1
1
2
2
ie
ib
dl
flow
he
water surface
2V
2g
2(V+dV)
2g
h h+dh
zb
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 5/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 74
b e
dh V.dVi i
dl g.dl (4-6)
We know that the quantity of water flowing per unit width is constant, therefore
q = V.h = constant (4-7)
dq
0dl
(4-8)
ord(Vh)
0dl
(4-9)
Differentiating the above equation (treating both V and h as variables),
V.dh h.dV0
dl dl (4-10)
dV V dh
dl h dl
(4-11)
Substituting the above value of dV
dlin Eq. (4-6), yields
2
b e
dh V dhi i
dl gh dl (4-12)
2
b e
dh V1 i i
dl gh
(4-13)
b e
2
i idh
dl V1gh
(4-14)
Notes: The above relation gives the slope of the water surface with respect to the bottom
of the channel. Or in other words, it gives the variation of water depth with respect to the
distance along the bottom of the channel. The value of dh/dl (i.e. zero, positive or negative)
gives the following important information:
If dh/dl is equal to zero, it indicates that the slope of the water surface is equal to
the bottom slope. Or in other words, the water surface is parallel to the channel
bed.
If dh/dl is positive, it indicates that the water surface rises in the direction of flow.
The profile of water, so obtained, is called backwater curve.
If dh/dl is negative, it indicates that the water surface falls in the direction of flow.
The profile of water, so obtained, is called downward curve.
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 6/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 75
Example 4.1: A rectangular channel, 20 m wide and having a bed slope of 0.006, is
discharging water with a velocity of 1.5 m/s. The flow is regulated in such a way that the
slope of the water energy gradient is 0.0008. Find the rate at which the depth of water will
be changing at a point where the water is flowing 2 m deep.
Solution:Given: width of the channel: b = 20 m
bed slope: ib = 0.006
velocity of water: V = 1.5 m/s
slope of energy line: ie = 0.0008
depth of water: h = 2 m
Letdh
dlbe the rate of change of water depth. Using equation in (4-14):
b e
2
i idh
dl V
1 gh
= 0.0059 Ans.
4.2. GRADUALLY-VARIED STEADY FLOW
4.2.1. Backwater calculation concept
Gradually varied flow is a steady, non-uniform flow in which the depth variation in
the direction of motion is gradual enough to consider the transverse pressure distribution as
being hydrostatic. This allows the flow to be treated as one-dimensional with no transverse
pressure gradients other than those due to gravity.
For subcritical flows the flow situation is controlled by the downstream flow conditions. Adownstream hydraulic structure (e.g. bridge piers, gate) will increase the upstream depth
and create a “ backwater” effect. This concept has been introduced shortly in section 4.1.3.
The term “ backwater calculation” refers more generally to the calculation of the
longitudinal free-surface profile for both subcritical and supercritical flows. The backwater
calculation is developed assuming:
a non-uniform flow
a steady flow
that the flow is gradually varied , and
that, at a given section, the flow resistance is the same as for a uniform flow with
the same depth and discharge, regardless of trends of the depth.
4.2.2. Equation of gradually-varied flow
In addition to the basic gradually-varied flow assumption, we further assume that
the flow occurs in a prismatic channel, or one that is approximately so, and that the slope
of the energy grade line can be evaluated from uniform flow formulas with uniform flow
resistance coefficients, using the local depth as though the flow were locally uniform.
Referring to Fig. 4.4., the total energy head at any cross-section is
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 7/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 76
2
VH z h
2g (4-15)
in which z = channel bed elevation; h = water depth, = kinetic-energy correction
coefficient as introduced in Chapter 2, and V = mean flow velocity.
Fig 4.4. Definition sketch for gradually-varied flow
If this expression for H is differentiated with respect to x, the coordinate in the flow
direction, the following equation is obtained:
dx
dEii
dx
dHbe with
2V
E h2g
(4-16)
in which ie is defined as the slope of the energy grade line; ib is the bed slope (= - dz/dx);
and E is the specific-energy head (i.e. the energy head with respect to the bottom). Solving
for dE/dx gives the first form of the equation of gradually varied flow:
eb iidx
dE (4-17)
It appears from this equation that the specific-energy head can either increase or decrease
in the downstream direction, depending on the relative magnitudes of the bed slope and the
slope of the energy grade line. Yen (1973) showed that, in the general case, ie is not the
same as the friction slope if (= 0 / R, this equation will be introduced again in Chapter 7)
or the energy dissipation gradient. Netherless, we have no better way of evaluating this
slope than applying uniform-flow formulas such as those of Manning or Chezy. It is
incorrect, however, to mix the friction slope, which clearly comes from a momentum
analysis, with terms involving , the kinetic-energy correction (Martin and Wiggert, 1975).
Note: The bed slope ie and the friction slope if are defined as:
oe f
z Hi = sin tan and i
x x R
respectively, where H is the mean total energy-head, z is the bed elevation, is the channel
slope and o is the bottom shear stress.
bed
h
2V
2 g
z
slope of energy grade line, ie
datum
dH
H
bed slo e i
dx
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 8/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 77
The second form of the equation of gradually-varied flow can be derived if it is recognized
thatdE dE dh
dx dh dx and that, applying equation (4-11),
2dE1 Fr
dh , provided that the
Froude number is properly defined. Then, equation (4-17) becomes:
b e
2
i idh
dx 1 Fr
(4-18)
The definition of the Froude number in equation (4-18) depends on the channel geometry.
For a compound channel, it should be the compound-channel Froude-number, while for a
regular, prismatic channel, in which d /dh is negligible, it assumes the conventional
energy definition given by Q2B/gA
3.
The ratio dh/dx in Eq. (4-18) represents the slope or the tangent to the water surface at any
point along the channel. This relationship therefore indicates whether at any point along
the channel the water surface is rising (backwater condition) or dropping (drawdown
condition). Immediately the following deductions can be made:
Whendh
0dx
, the slope of the water surface is dropping in the downstream
direction and the depth decreases downstream.
Whendh
0dx
, the slope of water surface is parallel to the channel bottom and
uniform flow exists. This can be readily seen from Eq. (4-18) since, for this
condition, ib = ie must equal zero.
Whendh
0dx
, the slope of water surface rises in the downstream direction and the
depth h increases downstream.
Whendh
dx , which requires that 1 – Fr
2= 0 or Fr = 1, the slope of the water
surface must theoretically be vertical. This flow occurs when the flow changes
from subcritical to supercritical, or vice versa, as indicated by the value of the
Froude number. The formulas derived do not actually apply any longer due to the
assumptions made. A vertical water surface also does not occur in reality; however,
a very noticeable change in the water surface takes place. This is especially so
when the flow changes from below hc to above hc. In such instance a phenomenon
known as the hydraulic jump occurs.
4.3. TYPES OF WATER SURFACE PROFILES
4.3.1. Classification of flow profiles
From the foregoing, it is evident that the relationship expressed in Eq. (4-18)
provides a considerable amount of information as to the shape of the water surface profile
in an open channel. Investigation of this formula yields the following results:
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 9/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 78
1. The relationship between the slope of the channel bottom and the slope of the
energy grade line determines whether the numerator of the equation is positive or
negative.
2. The denominator of the equation is positive if Fr < 1.0 and vice versa. In other
words, if the flow is subcritical (Fr smaller than 1) the denominator is positive, and
if the flow is supercritical (Fr greater than 1) the denominator is negative.
The conditions at which flow in an open channel can take place and the possible
relationships between the observed depth ho, the normal depth at which flow is uniform hn,
and the critical depth hc are illustrated in Fig. 4.5. It is evident from this figure that there
are three zones of channel depths at which flow can be observed:
Zone 1, with ho greater than hn and hc (i.e. ho > hn > hc)
Zone 2, with ho between hn and hc (i.e. hn > ho > hc)
Zone 3, with ho less than hn and hc (i.e. hn > hc > ho)
Fig.4.5. Three zones of channel depths
The relative bottom slope defines whether uniform flow is subcritical or supercritical.
Determine the associated Froude-number Fre.
2 22 e e e
e
e e e
V R VFr
gh h gR
where R is the hydraulic radius of the open channel flow. Subcript e denotes the
equilibrium flow. The bottom/wall shear stress is defined as:
2
o f e e f c V gR i
2
e bf
e f f
V ii
gR c c (the friction slope if = the bed slope ib )
2 e b
e
e f
R iFr
h c
We have: Ae = Be.he e e ee
e e
A P .Rh
B B , where Pe is the equilibrium wetted perimeter.
ho hn
hc
ho > hn > hc
hohn
hc
hn > ho > hc
ho
hn
hc
hn > hc > ho
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 10/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 79
2 e b
e
e f
B iFr
P c
In case of turbulent flow: 1.
For two-dimensional flow: e e
e e
R B1
h P
So, a proper approximation for Fre is: 2 be
f
iFr
c
If ib < cf , we have a mild slope (M – type)
The “uniform flow” is subcritical: Fr e2
< 1, he > hc.
If ib > cf , we have a steep slope (S – type)
The “uniform flow” is supercritical: Fr e2
> 1, he < hc.
If ib = cf , we have a critical slope (C – type) Fre2 = 1, he = hc
Note: It can easily be derived that
12 3
f 2
g
c n gRC
, where C is Chezy coefficient and n
is Manning’s.
Two conditional channel bottom conditions or slopes exist. These do not really constitute
open channel flow, but gravity flow can take place along them. They are as follows:
If ib < 0, we have an adverse slope (A – type)
If ib = 0, we have a horizontal slope (H – type)
It should be noticed that hn = he.
Note: The actual flow depends on the boundary condition, i.e.“mild
”,“steep
”, etc. does
not tell us anything about the actual flow.
4.3.2. Sketching flow profiles
In theory, for each of the five slope descriptions above there are three zones in
which flow can be observed. It follows then that a total of 15 theoretical water surface
profiles are possible, presented in Table 4.1. These profiles, together with illustrations of
practical applications, are shown in Fig. 4.6.
While this figure is for the most part self-explanatory, the following observations and
explanations are presented for further clarification. Mild slope (ib < cf ). The M1 curve is generally very long and asymptotic to the
horizontal and the line representing ho. The M2- and M3-curves end in a sudden
drop through the line representing hc and a hydraulic jump, respectively.
Critical slope (ib = cf ). Since hc = hn in this case, there is no zone 2, and only two
water surface profiles exist, C1 and C3. The C2-curve coincides with the water
surface that corresponds to uniform flow at critical depth.
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 11/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 80
Steep slope (ib > cf ). All curves are relatively short. S1 is asymptotic to the
horizontal, whereas S2 and S3 approach ho.
Horizontal slope and Adverse slope channels. In this case, hn is infinitely large and
uniform flow cannot take place. Hence there are no H1- or A1-profiles.
Table 4.1. Types of flow profiles in prismatic channelsDesignation Relation of ho
to hn and hc Channel
slope Zone
1
Zone
2
Zone
3
Zone
1
Zone
2
Zone
3
General type
of curve
Type of flow See
Fig.
M1 ho > hn > hc Backwater Subcritical
M2 hn > ho > hc Drawdown Subcritical
Mild
Fre2
< 1,
he > hc M3 hn > hc > ho Backwater Supercritical
4.6.a
C1 ho > hc = hn Backwater Subcritical
C2 hc = ho = hn Parallel to
channel bottom
Uniform
critical
Critical
Fre
2
= 1,he = hc C3 hc = hn > ho Backwater Supercritical
4.6.b
S1 ho > hc > hn Backwater Subcritical
S2 hc > ho > hn Drawdown Supercritical
Steep
Fre2
> 1,
he < hc S3 hc > hn > ho Backwater Supercritical
4.6.c
None ho > hn > hc None None
H2 hn > ho > hc Drawdown Subcritical
Horizontal
ib = 0
H3 hn > hc > ho Backwater Supercritical
4.6.d
None ho > (hn*) > hc None None
A2 (hn*) > ho > hc Drawdown Subcritical
Adverse
ib < 0
A3 (hn*
) > hc > ho Backwater Supercritical
4.6.e
hn*
in parentheses is assumed a possitive value.
CDL = critical-depth line; NDL = normal-depth line
horizontal
Mild slope
M1
M2
M3hc
hn
NDL
CDL
Fig.4.6.a. Mild slope (0 < ib < cf ) and examples of flow profiles
M1M1
M2 section of
enlargementM2
M3M3
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 12/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 81
Fig.4.6.b. Critical slope (ib = cf > 0) and examples of flow
critical slope
C1
C3hc = hn
CDL = NDL
horizontal
C1
C3
steep slope
S1
S2
S3
hn
hc
NDL
CDL
horizontal
Fig.4.6.c. Steep slope (ib > cf > 0) and examples of flow profiles
S1
S1
S2
section of
enlargement
S2
S3
S3
H2
H3hc CDL
horizontal slope
horizontal
Fig.4.6.d. Horizontal slope (ib = 0) and examples of flow profiles
H2
H3
A2
A3
hc
CDL
adverse slope
Fig.4.6.e. Adverse slope (ib < 0) and examples of flow
A2
A3
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 13/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 82
4.3.3. Prismatic channel with a change in slope
This channel is equivalent to a pair of connected prismatic channels of the same
cross section but with different slope. Several typical flow patterns along a prismatic
channel with a break or discontinuity in slope are shown in Fig. 4.7.
Fig. 4.7. Flow profiles with a change in slope
The profiles in Fig. 4.7 are self-explanatory. However, some special features should be
mentioned:
The profile near or at the critical depth cannot be predicted precisely by the theory
of gradually varied flow, since the flow is generally rapidly varied there.
In passing a critical line, the flow profile should, theoretically, have a vertical
slope. Since the flow is usually rapidly varied when passing the critical line, the
actual slope of the profile cannot be predicted precisely by the theory. For the same
reason, the critical depth may not occur exactly above the break of the channel
bottom and may be different from the depth shown in the figure.
NDL
NDL
mildmilder (very long)
CDL
M1 M1
M2hn1
hn2
hc NDL
S2
S2S3 CDLhc
hn1
hn2
steep (very long)
steeper
NDL
mild
steep
CDL
M2
NDL
S2hn1
hn2
hc
NDLsteep
CDL
NDL
S2H
hc
reservoir
NDL
mild (short)CDL
NDLM2
H
hn
reservoir
hc
tailwater
CDL
reservoir
NDL
mild (very long)
M2H
hn
hc
free overfall
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 14/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 83
4.3.4. Composite flow profiles with various controls
Channels with a number of controls will have flow profiles that can be composed
from the different types of flow profiles presented in the previous section. The ability to
sketch the composite profiles is in many cases necessary for understanding the flow in the
channel or for determining the discharge. In all cases it is necessary to identify firstly the
controls operating in the channel, and then to trace the profiles upstream and downstreamof these controls.
Two simple cases are shown in Fig. 4.8; in the first case the slope is mild, in the second
case steep. The curves for the mild-slope situation are self-explanatory, since they
incorporate many of the features already discussed. For the steep-slope situation we have
already seen that the critical flow must occur at the head of the slope – i.e. at the outflow
from the reservoir; thereafter there must be an S2-curve tending towards the uniform-depth
line. There must be an S1-curve behind the gate, and the transition from the S2- to the S1-
curve must be via a hydraulic jump. Downstream of the sluice gate, the flow will tend to
the uniform condition via an S2- or S3-curve; thence it proceeds over the fall at the end of
the slope. In this case there is nothing that impels the flow to seek the critical condition.
In Fig. 4.8 two profiles are drawn in dashed lines above the M3- and the S2-curve. These
are loci of depths conjugated to the corresponding depths on the underlying real surface
profiles, and are therefore known as “conjugate curves”. Obviously a hydraulic jump will
occur where such a curve intersects the real (subcritical) surface profile downstream; the
conjugate curve therefore provides a convenient means of determining the location of a
hydraulic jump.
Fig. 4.8. Examples of composite longitudinal profiles
M1
M2
M3
conjugate curve
hn
hc jump overfall
reservoir
mild slope
S1
S2 S3
conjugate curve
hn
hc
jump
overfall
reservoir
steep slope
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 15/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 84
4.4. DRAWING WATER SURFACE PROFILES
4.4.1. Direct-step methodThe computation of a flow profile by a step method consists of dividing the channel
into short reaches and determining reach by reach the change in depth for a given length of
a reach. In principle, the direct-step method could be applied to either Eq.(4-17) or Eq. )4-
18), but usually is associated with the former. Eq. (4-17) is put into finite-difference form
by approximating the derivative dE/dx with a forward difference and by taking the mean
value of the slope of the energy grade line over the step size x = (xi+1 – xi) in which thedistance x and the subscript i increase in the downstream direction. The result is:
eb
i1ii1i
ii
EExx
(4-19)
where ei is the arithmetic mean slope of the energy grade line between section i and section
i + 1, with the slope evaluated individually from Manning’s equation at each cross section.
The variables Ei+1, Ei and ei on the right hand side of Eq. (4-19) all are functions of the
depth h. The solution proceeds in a stepwise fashion in x by assuming values of depth h
and therefore values of the specific-energy head, E. As Eq. (4-19) is written, x increases inthe downstream direction. In general, upstream computations utilize Eq. (4-19) multipliedby ( – 1), so that the current value of the specific-energy head is subtracted from the
assumed value in the upstream direction and x becomes (xi+1 – xi), which is negative.Therefore, if the equation is solved in upstream direction for an M2-profile, for example,
the computed values of x should be negative for increasing values of h. Decreasing
values of h should result also in negative values of x for an M1-profile. For an M3-profile, which is supercritical, increasing values of depth in the downstream direction
correspond to decreasing values of the specific-energy head, and Eq. (4-19) indicates
positive values of x, since ei > ib.
Although the direct-step method is the easiest approach, it requires interpolation to find the
final depth at the end of the profile in a channel of specified length. Some care must betaken in specifying starting depths and checking for depth limits in a computer program. Inan M2-profile, for example, the starting depth should be taken slightly greater than the
computed critical depth, if it is a control, because of the slight inaccuracy inherent in thenumerical evaluation of critical depth. In addition, the M2-profile approaches the normal
depth asymptotically in the upstream direction, so that some arbitrary stopping limit must
be set, such as 99% of the normal depth.
Example 4.2: A trapezoidal channel has a bottom width b of 8.0 m and a side slope ratio
of 2:1. The Manning’s n of the channel is 0.025 m-1/3s, and the channel is laid on a slope of
0.001. If the channel ends in a free overfall, compute the water surface profile for a
discharge of 30 m3 /s.
Solution:
Given: bottom width: b = 8.0 m
side slope ratio: m:1 = 2:1
Manning’s n: n = 0.025 m-1/3
s
bed slope: ib = 0.001discharge: Q = 30 m
3 /s
Compute the water surface profile.
b
hn
m = 2
1
B
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 16/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 85
First, the normal depth and the critical depth must be determined. Manning’s equation
reads as:
21
b3
2
i.R.A.n
1Q
with trapezoidal channel cross-section:n nA y (b mh )
and hydraulic radius:n n
2
n
A h (b mh )
R P b 2h 1 m
So, the Manning equation can be rewritten as:5 52
3 332n n3
2 2 13 3 22
bn
A A [h (b mh )] Q.nA.R A.
P iP b 2h 1 m
or,
53
8 8n n 3 3
2 13 22
n
h (8.0 2y 30 0.025m 23.72 m
0.0018 2h 1 2
hn = 1.754 m
From the Froude formula:1
2
32
V Q QBFr
gD A A gA g.
B
where B = b+ 2mh; D = A/B, the hydraulic depth. In case of critical flow:
1 332 22c c cc
1 132 22
c cc
QB h b 2hA QFr 1
gA g b 2mhB
or
32
5c c 21
2c
h 8 2h 30m
9.818 2 2 h
hc = 1.03 m
Due to hn > hc, this is a mild slope (ib = 0.001): we have an M2-profile that has a critical
depth at the free overfall as boundary condition.
The direct-step method, as applied to Example 4.2, can be solved in a spreadsheet(Microsoft Excel) as formatted in Table 4.2. The values of h are selected in the first
column (1). The formulas for determining the specific-energy head E, column (5), and theslope of the energy grade line ie, column (6), for a given depth, are presented below. The
arithmetic mean of ie (iebar = ei ) is computed in column (7), and the change in specific-
energy head E, DelE, in the upstream direction is shown in column (8). Formulas applied
in the spreadsheet:
2
A y(b mh)
P b 2h 1 m
Q QR ; V
P A
2
2
e 43
e1 e2ebar e1 e2
VE h
2g
(nV)i
R
(i i )i (i i ) / 2
2
2 1
b ebar
e1 e2
E Del.E E E
Del.Ex Del.x
(i i )
x Del.E /(i i )
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 17/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 86
Then, the equation of gradually varied flow in finite difference form is solved for the
distance step x, aseb ii
Ex
= - 0.028 m in the first step.
Table 4.2. Water surface profile computation by the direct-step method.h A R V E ie iebar Del.E Del.x Sum Del.x
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)1.03 10.362 0.822 2.895 1.457 6.80E-03 0.00
1.04 10.483 0.829 2.862 1.457 6.58E-03 6.69E-03 1.62E-04 -0.028 -0.03
1.06 10.727 0.842 2.797 1.459 6.15E-03 6.36E-03 1.23E-03 -0.229 -0.26
1.08 10.973 0.855 2.734 1.461 5.75E-03 5.95E-03 2.35E-03 -0.476 -0.73
1.1 11.220 0.868 2.674 1.464 5.39E-03 5.57E-03 3.40E-03 -0.743 -1.48
1.12 11.469 0.882 2.616 1.469 5.06E-03 5.23E-03 4.36E-03 -1.032 -2.51
1.14 11.719 0.895 2.560 1.474 4.75E-03 4.90E-03 5.26E-03 -1.346 -3.85
1.16 11.971 0.908 2.506 1.480 4.47E-03 4.61E-03 6.09E-03 -1.687 -5.54
1.18 12.225 0.921 2.454 1.487 4.20E-03 4.33E-03 6.86E-03 -2.057 -7.60
1.2 12.480 0.934 2.404 1.495 3.96E-03 4.08E-03 7.58E-03 -2.460 -10.06
1.22 12.737 0.947 2.355 1.503 3.73E-03 3.84E-03 8.24E-03 -2.898 -12.96
1.24 12.995 0.959 2.309 1.512 3.52E-03 3.63E-03 8.87E-03 -3.377 -16.33
1.26 13.255 0.972 2.263 1.521 3.32E-03 3.42E-03 9.45E-03 -3.901 -20.23
1.28 13.517 0.985 2.219 1.531 3.14E-03 3.23E-03 9.99E-03 -4.474 -24.71
1.3 13.780 0.998 2.177 1.542 2.97E-03 3.06E-03 1.05E-02 -5.105 -29.81
1.32 14.045 1.010 2.136 1.553 2.81E-03 2.89E-03 1.10E-02 -5.800 -35.61
1.34 14.311 1.023 2.096 1.564 2.67E-03 2.74E-03 1.14E-02 -6.568 -42.18
1.36 14.579 1.035 2.058 1.576 2.53E-03 2.60E-03 1.18E-02 -7.419 -49.60
1.38 14.849 1.048 2.020 1.588 2.40E-03 2.46E-03 1.22E-02 -8.368 -57.97
1.4 15.120 1.060 1.984 1.601 2.28E-03 2.34E-03 1.26E-02 -9.430 -67.40
1.42 15.393 1.073 1.949 1.614 2.16E-03 2.22E-03 1.30E-02 -10.624 -78.02
1.44 15.667 1.085 1.915 1.627 2.06E-03 2.11E-03 1.33E-02 -11.975 -90.00
1.46 15.943 1.097 1.882 1.640 1.96E-03 2.01E-03 1.36E-02 -13.514 -103.51
1.48 16.221 1.110 1.849 1.654 1.86E-03 1.91E-03 1.39E-02 -15.279 -118.79
1.5 16.500 1.122 1.818 1.668 1.77E-03 1.82E-03 1.41E-02 -17.324 -136.111.52 16.781 1.134 1.788 1.683 1.69E-03 1.73E-03 1.44E-02 -19.715 -155.83
1.54 17.063 1.146 1.758 1.698 1.61E-03 1.65E-03 1.47E-02 -22.546 -178.37
1.56 17.347 1.158 1.729 1.712 1.54E-03 1.57E-03 1.49E-02 -25.945 -204.32
1.58 17.633 1.170 1.701 1.728 1.47E-03 1.50E-03 1.51E-02 -30.099 -234.42
1.6 17.920 1.182 1.674 1.743 1.40E-03 1.43E-03 1.53E-02 -35.283 -269.70
1.62 18.209 1.194 1.648 1.758 1.34E-03 1.37E-03 1.55E-02 -41.925 -311.63
1.64 18.499 1.206 1.622 1.774 1.28E-03 1.31E-03 1.57E-02 -50.732 -362.36
1.66 18.791 1.218 1.596 1.790 1.22E-03 1.25E-03 1.59E-02 -62.951 -425.31
1.68 19.085 1.230 1.572 1.806 1.17E-03 1.20E-03 1.60E-02 -81.023 -506.33
1.7 19.380 1.242 1.548 1.822 1.12E-03 1.15E-03 1.62E-02 -110.433 -616.77
1.72 19.677 1.254 1.525 1.838 1.07E-03 1.10E-03 1.63E-02 -166.658 -783.42
1.74 19.975 1.266 1.502 1.855 1.03E-03 1.05E-03 1.65E-02 -316.826 -1100.25
1.745 20.050 1.269 1.496 1.859 1.02E-03 1.02E-03 4.14E-03 -171.079 -1271.33
Note that at least three significant figures should be retained in E to avoid large round-off
errors when the differences are small in comparison to the values of E. In the last column,
the cumulative values of x are given, and these represent the distance from the starting
point where the specified depth h is reached. After the first step, uniform increments in
depth h, with h increasing in the upstream direction, are utilized. The values of h are
stopped at the finite limit of 1.745 m, which is 99.5% of the normal depth. The length
required to reach this point is 1271 m, which is the length required for this channel to be
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 18/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 87
considered hydraulically long, but that length varies, in general. The depth increments can
be halved until the change in profile length becomes acceptably small. Alternatively,
smaller increments in depth can be used in regions of rapidly changing depth, and larger
increments may be appropriate in regions of very gradual depth-changes. A portion of the
computed M2-profile is shown in Fig. 4.9.
M2 water surface-profile
computed by the direct-step method
0
0,6
1,2
1,8
2,4
-1200 -1000 -800 -600 -400 -200 0
distance upstream (m)
d e p t h ( m )
Fig. 4.9. M2-curve drawn in example 4.2.
Example 4.3: A trapezoidal channel with a bottom width of 5 m, a side slope of 1:1, and a
Manning n of 0.013 m-1/3
s carries a discharge of 50 m3 /s at a bed slope of 0.0004. Compute
by the direct-step method the backwater profile created by a dam that backs up the water to
a depth of 6 m immediately in font of the dam. The upstream end of the profile is assumedat a depth equal to 1% greater than the normal depth.
Solution:
Given: bottom width: b = 5.0 m side slope ratio: m:1 = 1:1
Manning’s n: n = 0.013 m-1/3s bed slope: ib = 0.0004
discharge: Q = 50 m3 /s water depth: h = 6.0 m (in front of dam)
Compute the water surface profile.
Similar to Example 4.2: the normal depth and the critical depth are:5
3n n
2 13 22
bn
[h (b mh )] Q.n
ib 2h 1 m
hn = 2.87 m
M1
6 m
NDL
CDL hn hc ib = 0.0004
A
Dam
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 19/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON-UNIFORM FLOW 88
32
c c
12
c
h b 2h Q
gb 2mh
hc = 1.57 m
Because hn > hc the channel slope is mild. The profile lies in zone 1 and therefore it is anM1 curve. The range of depth is 6m at the downstream end and (101% x 2,87) = 2.90 m at
the upstream end. Students should try to make a table computation, which is self-explanatory and draw an M1 curve as Fig. 4.10 below:
M1 water surface-profile
computed by the direct-step method
0
1
2
3
4
5
6
7
-8000 -7000 -6000 -5000 -4000 -3000 -2000 -1000 0
distance upstream (m)
w a t e r d e p t h ( m )
i n f r o n t o f d a m
Fig. 4.10. M1-curve drawn in example 4.3.
4.4.2. Direct numerical integration methodThe direct integration method is applicable to prismatic channels only. This method
uses Eq. 4-18 as governing equation:
b e
2
i idh
dx 1 Fr
2
b e
1 Frdx dh
i i
(4-20)
In its integrated form, Eq. 4-20 becomes:i 1 i 1 i 1
i i i
x h h2
i 1 i
b ex h h
1 Frdx x x dh g(h)dh
i i
(4-21)
The integrand on the right hand side of Eq. (4-21) is a function of h, g(h), which can be
integrated numerically to obtain a solution for x, as shown as in Fig. 4.11.
Fig. 4.11. Water surface-profile computation by direct numerical integration
g(h)
hho hi hi+1hn
area = xi+1 - xi
7/27/2019 OCHC 4.pdf
http://slidepdf.com/reader/full/ochc-4pdf 20/20
OPEN CHANNEL HYDRAULICS FOR ENGINEERS
-----------------------------------------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------------------------------------
Chapter 4: NON UNIFORM FLOW 89
A variety of numerical integration techniques are available, such as the trapezoidal rule and
Simpson’s rule, which are commonly used to find the cross-sectional area of a natural
channel, for example. Simpson’s rule is of higher order in accuracy than the trapezoidal
rule, which simply means that the same numerical accuracy can be achieved with fewer
integration steps. Application of the trapezoidal rule to the right-hand side of Eq. (4-21) for
a single step produces:
i 1 ii 1 i i 1 i
g(h ) g(h )x x h h2
(4-22)
To determine the full length of a flow profile, (xl – xo), multiple application of the
trapezoidal rule results inl 1
o l i
i 1l o
g(h ) g(h ) 2 g(h )
L x x h2
(4-23)
where L is the profile length and h = (hi+1 – hi) is the uniform depth-increment. Because
the global truncation error in the multiple application of the trapezoidal rule is of order
(h)2, halving the depth increment will reduce the error in the profile length by a factor ¼.
By successively halving the depth interval, the relative change in the profile length can be
calculated with the process continuing until the relative error is less than some acceptable
value.