+ All Categories
Home > Documents > om Ron...EN ISO 13849-1 :2008 (Cat.1 PL c) EN 60947-5-3:2013 IEC 60947-5-3(ed.2) EN 50178:1997 The...

om Ron...EN ISO 13849-1 :2008 (Cat.1 PL c) EN 60947-5-3:2013 IEC 60947-5-3(ed.2) EN 50178:1997 The...

Date post: 05-Feb-2021
Category:
Upload: others
View: 6 times
Download: 0 times
Share this document with a friend
10
No.ESDD003D Original om Ron EU DECLARATION OF CONFORMITY 1. Product Models/Products: E3ZS-T81A series 2. Name and address of the manufacturer: OMRON Corporation Shiokoji-horikawa. Shimogyo-ku. Kyoto. 600-8530. JAPAN 3. This declaration of conformity is issued under the sole responsibility of the manufacturer. 4. Objects of the declaration: E3ZS-T81A Single-Beam Safety Sensor 5. The objects of the declaration described above are in conformity with the relevant Union harmonisation legislation: 2014/30/EU EMC Directive 2006/42/EC Machinery Directive 6. References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is declared: EMC Directive: EN 60947-5-3:2013, EN 61496-1:2013 Machinery Directive: EN 60947-5-3:2013. EN 61496-1:2013. EN 61496-2:2013, EN ISO 13849-1 :2015 When using E3ZS-T81A as a Type 2 ESPE. an appropriate safety controller complied with the requirements of the relevant standards (Category 2, PL c according to EN ISO 13849-1, Type 2 according to EN 61496-1 and -2) must be used. 7. Name, address, and identification number of Notified Body, Number of EC Type Examination: Machinery Directive: Notified body: TOV SOD Product Service GmbH Address: Zertifuierstelle, Ridlerstral:se 65.80339, MOnchen, Germany, Notified Body identification No.: 0123 112 GQ-151845Al
Transcript
  • No.ESDD003D

    Original om Ron EU DECLARATION OF CONFORMITY

    1. Product Models/Products:

    E3ZS-T81A series

    2. Name and address of the manufacturer:

    OMRON Corporation

    Shiokoji-horikawa. Shimogyo-ku. Kyoto. 600-8530. JAPAN

    3. This declaration of conformity is issued under the sole responsibility of the

    manufacturer.

    4. Objects of the declaration:

    E3ZS-T81A Single-Beam Safety Sensor

    5. The objects of the declaration described above are in conformity with the

    relevant Union harmonisation legislation:

    2014/30/EU EMC Directive

    2006/42/EC Machinery Directive

    6. References to the relevant harmonised standards used or references to the

    other technical specifications in relation to which conformity is declared:

    EMC Directive: EN 60947-5-3:2013, EN 61496-1:2013

    Machinery Directive: EN 60947-5-3:2013. EN 61496-1:2013. EN 61496-2:2013, EN

    ISO 13849-1 :2015

    When using E3ZS-T81A as a Type 2 ESPE. an appropriate safety controller complied

    with the requirements of the relevant standards (Category 2, PL c according to EN

    ISO 13849-1, Type 2 according to EN 61496-1 and -2) must be used.

    7. Name, address, and identification number of Notified Body, Number of EC Type

    Examination:

    Machinery Directive:

    Notified body: TOV SOD Product Service GmbH

    Address: Zertifuierstelle, Ridlerstral:se 65.80339, MOnchen, Germany,

    Notified Body identification No.: 0123

    112 GQ-151845Al

    doug.barnettHighlight

  • No.ESDD003D

    Certificate for EU Type Examination: Z1 0 15 10 39656 303, Z1 0 15 10 39656 304

    Signed and on behalf of: OM RON Corporation

    Place and date of issue:

    Signature:

    Name: Jaehyoung Yu

    Function: Industrial Automation Company, Safety Division. Safety

    Product Management Group Manager

    Name and address of contact in EU

    OMRON Europe B.V.

    Quality & Environment Department

    Attn: J.J.P.W. Vogelaar, European Quality & Environment Manager

    Zilverenberg 2, 5234 GM. 's-Hertogenbosch. The Netherlands

    Additional information

    Type: E3ZS-T81 A Series

    E3ZS - T81A- 0 L_j II

    : Blank, D or L

    II :Blank, or additionalletter(s) and/or number(s)

    2/2 GQ-151845Al

  • CER-r i FICATE No. Z10 15 10 39656 303

    Holder of Certificate: Omron Corporation Shiokoji Horikawa,Shimogyo-ku

    Kyoto

    Factory(ies):

    Certification Mark:

    Product:

    Model(s):

    600-8530 JAPAN

    48774, 56891

    Proximity switch (PDDB)

    E3ZS-T81A

    Product Service

    For nomenclature of product type see attachment

    Parameters:

    Tested according to:

    Power supply: Nominal current:

    Operating temperature: Protection class:

    2006/42/EC

    12-24VDC ±10% max. 15mA Emitter max. 20mA Receiver -1 0°C .. . +55°C IP67

    EN ISO 13849-1 :2008 (Cat.1 PL c) EN 60947-5-3:2013 IEC 60947-5-3(ed.2) EN 50178:1997

    The product was tested on a voluntary basis and complies with the essential requirements. The certification mark shown above can be affixed on the product. It is not permitted to alter the certification mark in any way. In addition the certification holder must not transfer the certificate to third parties. See also notes overleaf.

    Test report no.:

    Valid until:

    Date, 2015-10-14

    Page 1 of 2

    70035161

    2020-10-13

    TUV SUD Product Service GmbH · Zertifizierstelle · Ridlerstra~e 65 · 80339 Munchen · Germany

    doug.barnettHighlight

  • ATTACHMENT TO CERTIFICATE No. Z10 15 10 39656 303

    Nomenclature for E3ZS-T81A

    Single Beam Safety Sensor model

    E3ZS-T81A - () - ()

    II

    I. Emitter I Receiver

    L: Emitter

    D: Receiver

    Nothing: Emitter I Receiver

    II. Special customization

    Nothing: Standard model

    Additional letter(s), number(s): The following specification changes are

    indicated by this additional suffix.

    1) Cable length within maximum length specification

    2) The cable end is connector

    3) UL marking is not on the label

    4) User manual is not packed to the product

    5) Various type of mounting holes.

    Department: TR-RA/MUC

    2015-10-14 Date:

    Page 2 of 2

    Product Service

    "T1"1\/® TOV SOD Product Service GmbH · Zertifizierstelle · Ridlerstra!Se 65 · 80339 MUnchen · Germany •uv

    doug.barnettHighlight

  • ..,. 0

    Product Service

    CERTIFICATE No. Z10 15 10 39656 304

    Holder of Certificate: Omron Corporation Shiokoji Horikawa,Shimogyo-ku

    Kyoto

    Factory(ies):

    Certification Mark:

    Product:

    Model(s):

    Parameters:

    Tested according to:

    600-8530 JAPAN

    48774, 56891

    Electro-Sensitive Protective Equipment (AOPD) Type 2

    E3ZS-T81A For nomenclature of product type see attachment

    Power supply: 24VDC (supplied by safety controller)

    Nominal current: 15mA emitter, 20mA receiver Operating temperature: -1 0°C ... +55°C Protection class: IP67 Conditions: Use only with an appropriate safety controller

    2006/42/EC EN ISO 13849-1 :2008 (Cat. 2, PL c) IEC 61496-1(ed.3) IEC 61496-2(ed.3) EN 61496-1:2013 EN 61496-2:2013 EN 50178:1997

    The product was tested on a voluntary basis and complies with the essential requirements. The certification mark shown above can be affixed on the product. It is not permitted to alter the certification mark in any way. In addition the certification holder must not transfer the certificate to third parties. See also notes overleaf.

    Test report no.:

    Valid until:

    Date, 2015-10-14

    Page 1 of2

    70035164

    2020-10-13

    TUV SUD Product Service GmbH · Zertifizierstelle · Ridlerstra~e 65 · 80339 Mi.inchen · Germany

    doug.barnettHighlight

  • ATTACHMENT TO CERTIFICATE No. Z10 15 10 39656 304

    Nomenclature for E3ZS-T81A

    Single Beam Safety Sensor model

    E3ZS-T81A - () - ()

    II

    I. Emitter I Receiver

    L: Emitter

    D: Receiver

    Nothing: Emitter I Receiver

    II. Special customization

    Nothing: Standard model

    Additional letter(s), number(s): The following specification changes are

    indicated by this additional suffix.

    1) Cable length within maximum length specification

    2) The cable end is connector

    3) UL marking is not on the label

    4) User manual is not packed to the product

    5) Various type of mounting holes.

    Department: TR-RNMUC

    2015-10-14 Date:

    Page 2 of2

    Product Service

    T1"1\l® TOV SOD Product Service GmbH · Zertifizierstelle · Ridlerstraf5e 65 · 80339 Mi.inchen · Germany • uv

    doug.barnettHighlight

  • 1/29/2018 NIPF.E199694 - Active Opto-electronic Protective Devices

    http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=NIPF.E199694&ccnshorttitle=Active+Opto-electronic+Protective… 1/2

    NIPF.E199694 Active Opto-electronic Protective Devices

    Page Bottom

    Active Opto-electronic Protective Devices

    See General Information for Active Opto-electronic Protective Devices

    OMRON CORP E199694SAFETY STANDARDS GROUPIAB GLOBAL QUALITY CENTERSHIOKOJI HORIKAWASHIMOGYO-KU, KYOTO 600-8530 JAPAN

    Control units Model(s) F3SP-B1P

    End cap accessories Model(s) F39BT, F39BTLP, F39LP

    Type 2 and type 4 light curtain systems Model(s) F3SR, followed by 2 or 4, followed by 30, followed by B, followed by four numbers, may befollowed by L or D, may be followed by additional numbers and/or letters.

    Type 4 and type 2 light curtain systems Model(s) F3SG, followed by 2 or 4, followed by R, followed by E or A, followed by 0160-2510,followed by P, N or -, followed by 30, 25, 14, may be followed by L or D, may be followed by additional suffixes.

    Type 4 light curtains Model(s) F3SG, followed by 4, followed by R, followed by R, followed by 0240-1920, followed by P, N or -, followed by 14or 25, may be followed by L or D, may be followed by additional suffixes.

    Investigated to UL 1998

    Type 2 light curtain systems, emitters and receivers Model(s) F3SH-B, followed by xx, followed by P or N, followed by xx, may be followedby S or SS, followed by L, D or blank, may be followed by additional numbers and/or letters.

    F3SN-B, followed by xxxx, followed by P or N, followed by 12, 14, 25, 40, 55 or 70, may be followed by S, SS, H, HS or HSS, followed by L, D orblank, may be followed by additional numbers and/or letters.

    Type 2 or type 4 light curtain systems, emitters and receivers Model(s) F3SJ, followed by Blank or 2, followed by E or B, followed by0185-2065, followed by N, P or -, followed by 25, may be followed by L or D, may be followed by additional suffixes.

    Type 2 or type 4 light curtains Model(s) F3SJ-A or F3SJ-2A, followed by 0245-2495, followed by P or N, followed by 14, 20, 25, 30, 35, 55 or65, may be followed by L or D, may be followed by TS, 01TS, 01T, may be followed by additional suffixes.

    F3SJ-AM, followed by 2-4, followed by P or N, followed by 300, 400 or 500, may be followed by L or D, may be followed by additional suffixes.

    Type 2 single beam sensors Model(s) E3ZS, followed by T, followed by 8, followed by 1, followed by A, followed by D, L or blank, followed byadditional suffixes.

    Type 2 single beam systems, for use only with model F3SX control unit Model(s) E3FS-10

    Type 4 control units Model(s) F3SX, followed by N, E, H, M, NR, ER, HR, MR, followed by R, R1, R2, L1, L2, L4, M1, D1, P1, P2 and B1,followed by additional suffixes.

    Type 4 light curtain systems, emitters and receivers Model(s) F3SH-A, followed by xx, followed by P or N, followed by xx, may be followedby S or SS, followed by L, D or blank, may be followed by additional numbers and/or letters.

    F3SN-A, followed by xxxx, followed by P or N, followed by 12, 14, 25, 40, 55 or 70, may be followed by S, SS, H, HS or HSS, followed by L, D orblank, may be followed by additional numbers and/or letters.

    Trademark and/or Tradename: ,

    Last Updated on 2017-11-20

    Questions? Print this page Terms of Use Page Top

    © 2018 UL LLC

    The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufacturedunder UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Certified and covered under UL's Follow-UpService. Always look for the Mark on the product.

    http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?&name=NIPF.GuideInfo&ccnshorttitle=Active+Opto-electronic+Protective+Devices&objid=1074099219&cfgid=1073741824&version=versionless&parent_id=1073990175&sequence=1javascript:openit('gupdthlp.html')http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/gassist.htmljavascript:window.print()http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/terms_of_use.htmldoug.barnettHighlight

    doug.barnettHighlight

  • 1/29/2018 NIPF7.E199694 - Active Opto-electronic Protective Devices Certified for Canada

    http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=NIPF7.E199694&ccnshorttitle=Active+Opto-electronic+Protectiv… 1/2

    NIPF7.E199694 Active Opto-electronic Protective Devices Certified for Canada

    Page Bottom

    Active Opto-electronic Protective Devices Certified for Canada

    See General Information for Active Opto-electronic Protective Devices Certified for Canada

    OMRON CORP E199694SAFETY STANDARDS GROUPIAB GLOBAL QUALITY CENTERSHIOKOJI HORIKAWASHIMOGYO-KU, KYOTO 600-8530 JAPAN

    Control units Model(s) F3SP-B1P

    End cap accessories Model(s) F39BT, F39BTLP, F39LP

    Type 2 and type 4 light curtain systems Model(s) F3SR, followed by 2 or 4, followed by 30, followed by B, followed by four numbers, may befollowed by L or D, may be followed by additional numbers and/or letters.

    Type 2 light curtain systems, emitters and receivers Model(s) F3SH-B, followed by xx, followed by P or N, followed by xx, may be followedby S or SS, followed by L, D or blank, may be followed by additional numbers and/or letters.

    F3SN-B, followed by xxxx, followed by P or N, followed by 12, 14, 25, 40, 55 or 70, may be followed by S, SS, H, HS or HSS, followed by L, D orblank, may be followed by additional numbers and/or letters.

    Type 2 or type 4 light curtain systems, emitters and receivers Model(s) F3SJ, followed by Blank or 2, followed by E or B, followed by0185-2065, followed by N, P or -, followed by 25, may be followed by L or D, may be followed by additional suffixes.

    Type 2 or type 4 light curtains Model(s) F3SJ-A or F3SJ-2A, followed by 0245-2495, followed by P or N, followed by 14, 20, 25, 30, 35, 55 or65, may be followed by L or D, may be followed by TS, 01TS, 01T, may be followed by additional suffixes.

    F3SJ-AM, followed by 2-4, followed by P or N, followed by 300, 400 or 500, may be followed by L or D, may be followed by additional suffixes.

    Type 2 single beam sensors Model(s) E3ZS, followed by T, followed by 8, followed by 1, followed by A, followed by D, L or blank, followed byadditional suffixes.

    Type 2 single beam systems, for use only with model F3SX control unit Model(s) E3FS-10

    Type 4 and type 2 light curtain systems Model(s) F3SG, followed by 2 or 4, followed by R, followed by E or A, followed by 0160-2510,followed by P, N or -, followed by 30, 25, 14, may be followed by L or D, may be followed by additional suffixes.

    Type 4 control units Model(s) F3SX, followed by N, E, H, M, NR, ER, HR, MR, followed by R, R1, R2, L1, L2, L4, M1, D1, P1, P2 and B1,followed by additional suffixes.

    Type 4 light curtain systems, emitters and receivers Model(s) F3SH-A, followed by xx, followed by P or N, followed by xx, may be followedby S or SS, followed by L, D or blank, may be followed by additional numbers and/or letters.

    F3SN-A, followed by xxxx, followed by P or N, followed by 12, 14, 25, 40, 55 or 70, may be followed by S, SS, H, HS or HSS, followed by L, D orblank, may be followed by additional numbers and/or letters.

    Type 4 light curtains Model(s) F3SG, followed by 4, followed by R, followed by R, followed by 0240-1920, followed by P, N or -, followed by 14or 25, may be followed by L or D, may be followed by additional suffixes.

    Trademark and/or Tradename: ,

    Last Updated on 2017-11-20

    Questions? Print this page Terms of Use Page Top

    © 2018 UL LLC

    The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufacturedunder UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Certified and covered under UL's Follow-UpService. Always look for the Mark on the product.

    UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The GuideInformation, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) must be presented in their entirety and in a non-

    http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?&name=NIPF7.GuideInfo&ccnshorttitle=Active+Opto-electronic+Protective+Devices+Certified+for+Canada&objid=1074184209&cfgid=1073741824&version=versionless&parent_id=1073990177&sequence=1javascript:openit('gupdthlp.html')http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/gassist.htmljavascript:window.print()http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/terms_of_use.htmldoug.barnettHighlight

  • Here are the links to the following OMRON UL Files: NIPF.E199694 - Active Opto-electronic Protective Devices NIPF7.E199694 - Active Opto-electronic Protective Devices Certified for Canada Put the cursor on the (underlined & highlighted in blue), press Ctrl, then Click. This will bring you to UL’s Online Directory for that UL File

    Company Name Category Name Link to File

    OMRON CORP Active Opto-electronic Protective Devices

    NIPF.E199694

    OMRON CORP

    Active Opto-electronic Protective Devices Certified for Canada

    NIPF7.E199694

    http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=NIPF.E199694&ccnshorttitle=Active+Opto-electronic+Protective+Devices&objid=1074281338&cfgid=1073741824&version=versionless&parent_id=1073990175&sequence=1http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=NIPF7.E199694&ccnshorttitle=Active+Opto-electronic+Protective+Devices+Certified+for+Canada&objid=1074311293&cfgid=1073741824&version=versionless&parent_id=1073990177&sequence=1

  • OMRON CANADA, INC. • HEAD OFFICEToronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com

    OMRON ELECTRONICS DE MEXICO • HEAD OFFICEMéxico DF • 52.55.59.01.43.00 • 01-800-226-6766 • [email protected]

    OMRON ELECTRONICS DE MEXICO • SALES OFFICEApodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • [email protected]

    OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICESão Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br

    OMRON ARGENTINA • SALES OFFICECono Sur • 54.11.4783.5300

    OMRON CHILE • SALES OFFICESantiago • 56.9.9917.3920

    OTHER OMRON LATIN AMERICA SALES54.11.4783.5300

    Authorized Distributor:

    J89I-E-01 11/14 Note: Specifications are subject to change. © 2014 Omron Electronics LLC Printed in U.S.A.

    Printed on recycled paper.

    Automation Control Systems• Machine Automation Controllers (MAC) • Programmable Controllers (PLC) • Operator interfaces (HMI) • Distributed I/O • Software

    Drives & Motion Controls • Servo & AC Drives • Motion Controllers & Encoders

    Temperature & Process Controllers • Single and Multi-loop Controllers

    Sensors & Vision• Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors• Amplified Photomicrosensors • Measurement Sensors• Ultrasonic Sensors • Vision Sensors

    Industrial Components • RFID/Code Readers • Relays • Pushbuttons & Indicators• Limit and Basic Switches • Timers • Counters • Metering Devices • Power Supplies

    Safety • Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety Controllers • Light Curtains • Safety Relays • Safety Interlock Switches

    OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com

    OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu


Recommended