Omn Te Ad Mobile

8/13/2019 Omn Te Ad Mobile

1/46

GSM Switching Subsystem

SSS SR13.0/UCR5.0cs

OMN:TE-AD

A30828-Y1160-U3-1-7620


2/46


3/46

A30828-Y1160-U3-1-7620

3

OMN:TE-AD

Id:0900d8058018c604

Table of ContentsThis document has 46 pages.

1 Introduction (IN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71.1 Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.2 Test Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.2.1 Assignment of Test Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.2.2 Operating States of the Exchange. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.2.3 Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1.2.4 Test Equipment Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

1.2.5 Test Points for Test Traffic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

1.2.6 Thresholds for ATE and TU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.2.7 Test Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.2.8 Test Results. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.2.9 Workstations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.2.10 Workstation Test Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.2.11 Workstation Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.3 Administration of Test Objects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.3.1 Subscriber Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1.3.2 Administration of Thresholds for Line Testing . . . . . . . . . . . . . . . . . . . . 17

1.3.3 Test Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.3.4 Trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.3.5 Trunk Group Test Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.4 Line Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

1.4.1 Testing with the Line Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181.4.2 Tests with the ATE:T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1.4.3 Automatic Tests with the TU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1.4.4 Tests with the Ringback Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1.4.5 ISDN Line Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1.4.6 SULIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1.5 Trunk Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

1.5.1 Testing with the Trunk Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

1.5.2 Tests with the ATE:T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

1.5.3 Tests with the ATE:TM / ATE:N/ ATCO. . . . . . . . . . . . . . . . . . . . . . . . . 20

1.5.4 Tests with the Testset (Test Phone) . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1.6 Safeguarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2 Tasklist (TL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.1 Test Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.1.1 Operating states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.1.2 Display operating states of test equipment . . . . . . . . . . . . . . . . . . . . . . 22

2.1.3 Test equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.1.4 Test equipment data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.1.5 Thresholds for ATE/TU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.1.6 Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.1.7 Workstation group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.1.8 Workstation test port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24


4/46

4 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d8058018c604

2.1.9 Test schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.1.10 Test jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.1.11 Test results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.2 Administration of Test Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242.2.1 Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.2.2 Administration of thresholds for line testing . . . . . . . . . . . . . . . . . . . . . . 25

2.2.3 Test classes for subscriber lines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.2.4 Trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.2.5 Trunk data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.2.6 Trunk group test data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.2.7 Administration of thresholds for international trunk testing . . . . . . . . . . . 25

3 Procedures (TP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4 TP-002 - Create testset at DLU port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5 TP-003 - Cancel testset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6 TP-004 - Create ringback service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

7 TP-011 - Create SMC as TLWS workstation connected via NetM . . . . . 32

8 TP-012 - Create OMT as TLWS workstation . . . . . . . . . . . . . . . . . . . . . 34

9 TP-015 - Cancel workstation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

10 TP-016 - Modify worktstation data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

11 TP-017 - Modify workstation group data. . . . . . . . . . . . . . . . . . . . . . . . . 39

12 TP-018 - Cancel workstation group . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

13 TP-019 - Cancel workstation test port. . . . . . . . . . . . . . . . . . . . . . . . . . . 42

14 TP-021 - Display intermediate test results . . . . . . . . . . . . . . . . . . . . . . . 43

15 TP-022 - Display test job. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

16 TP-030 - Display test results from archive fi le . . . . . . . . . . . . . . . . . . . . 45


5/46

A30828-Y1160-U3-1-7620

5

OMN:TE-AD

Id:0900d8058018c604

List of FiguresFigure 1 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8


6/46


7/46

A30828-Y1160-U3-1-7620

7

OMN:TE-AD Introduction (IN)

Id:0900d805800a677b

1 Introduction (IN)

gDepending on the scope of your project, this manual may contain more information-

than you require.


8/46

8 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a677b

Introduction (IN)

1.1 Interfaces

Figure 1 Interfaces

EXIT

U M N : T E

ENTRY:

EXIT:

(from cross-refer-

ence) AD

Administration

SUB

Subscribers

TRK

Trunks

MaintenanceIntroduction

INFC:SUB, INFC:TRK

Task List for Maintenance

TLFC:SUB, TLFC:TRKMMN:TESUBTLFC

MMN:TETRKTLFC

Output masks

TEST RESULTS

Fault clearance pro

cedure no: FCxx

Fault Clearance Procedures FCxx

Tables TABxx

MMN:xxx

(continuation after

cross-reference)

Nonst. maintenance

OA&M center

(from test order)

Test Procedures

TPxxx

Administration and OperationIntroduction

IN:AD, IN:SUB, IN:TRK

Task List for Operation

TL:AD, TL:SUB, TL:TRK

Tables

TABxx


9/46

A30828-Y1160-U3-1-7620

9


Id:0900d805800a677b

Key to interface diagram

MMN:xxx: Fault clearance procedures MMN:LTGx or MMN:DLU

OA&M: center Operation administration and maintenance center

Figure 1shows an overview of the UMN:TE interfaces. It contains the links to other

manuals. In addition to this, the overview shows where you can find task lists or fault

clearance procedures to match output masks or test results..

This manual is used in the system for the administration of tests and test objects.

1.2 Test Administration

1.2.1 Assignment of Test Commands

Table 1shows how test objects are assigned to test commands.

Test object Hardwar

e

Test

equip-

ment

Test command

Special circuit (ATE:T, TOG,

RESP)

LTG ATE:T TEST CTYPE, TEST LIC,

TEST LTGPOS

Special circuit (ATE:TM /

ATE:N /ATCO)

LTG ATE:TM

ATE:N

ATCO

TEST CTYPE

Analog subscriber line circuit DLU TU /DLUG

TEST SLC, TEST DLULC

Special circuit (TU) DLU TU TEST DLULC

Analog PBXline, trunk-

scriber

LTGB/C ATE:T TEST PBXLN

Analog PBX line DLU ATE:T TEST PBXLN

Routine test of analog sub-

scriber line

DLU TU /

DLUG

TEST SUB

Routine test of BA DLU TU /

DLUG

TEST SUB, TEST ISUB

ISDNmeasurements DLU START RDSMEAS,

ACT BAPERF

Manual test of subscriber line

and terminal connected to

SLMA

DLU TU /

DLUG,

LWS

ACT WST, START LTEST,

TEST LINE

Manual test of subscriber line

and terminal connected to

BA

DLU TU /

DLUG,

LWS

ACT WST, START LTEST,

TEST LINE

Table 1 Assignment of test commands
http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/


10/46


11/46

A30828-Y1160-U3-1-7620

11


Id:0900d805800a677b

TEST SUB

digital TEST

ISUB

ACT ACT

CBL

- ACT

CBL

ACT

CBL

- NOTST

SUL

ACT -

TEST LOOPBA ACT ACT

CBL

- ACT

CBL

ACT

CBL

ADMIN/

1/2/3

ACCSU

SP

NOTST

SUL _

-

TEST PA - - MBL ACT

CBL

- - - - -

Running digital

sum measure-

ment

ACT ACT

CBL

- ACT

CBL

ACT

CBL

ADMIN/

1/2/3

ACCSU

SP

_

-

BA perfor-

mance mea-

surement

ACT ACT

CBL

- ACT

CBL

ACT

CBL

ADMIN/

1/2/3

ACCSU

SP

- - -

BLOCKING refers to ADMIN /ADMIN1, 2, 3, account suspension and trunk state

BMNT

LNATT refers to NOTSTSUL

NO Testing not possible in any of the listed states

ATE refers to ATE not blocked / CBL / MBL

Port Mod

ule

DIU LTG DLU BLOCK

ING

LNATT TU

mod

ule/

port

ATE ATE

:TM

ATE

:N

AT

CO

RBS

analog

DLU

ACT ACT - ACT ACT ADMIN/

1/2/3

ACCSU

SP

NO ACT - -

Table 3 Operating states that permit testing, 2

Port Mod

ule

DIU LTG DLU BLOCK

ING

LNATT TU

mod

ule/

port

ATE

Table 2 Operating states that permit testing, 1 (Cont.)
http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


12/46

12 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a677b

Introduction (IN)

1.2.3 Test Equipment

The different types of test equipment are used to test trunks, lines, line circuits, PBX

lines, terminals, tone generators, announcements and for self-testing of the test equip-

ment itself.

The following types of test equipment can be created with command CR TEQ

RBS

digital

ACT ACT - ACT ACT ADMIN/

1/2/3

ACCSU

SP

NOTST

SUL

- - -

LWS

analog

DLU

ACT ACT

CBL

- ACT

CBL

ACT

CBL

ADMIN/

1/2/3

ACCSUSP

NO ACT - -

LWS

digital

ACT ACT

CBL

- ACT

CBL

ACT

CBL

ADMIN/

1/2/3

ACCSU

SP

NO ACT - -

TWS ACT

CBL

- ACT

CBL

ACT

CBL

- BMNT

ADMIN

- - - ACT

TEST

TRUNK

ACT

CBL

- ACT

CBL

ACT

CBL

- BMNT - - ACT -

TEST

INTLTRK

ACT

CBL

- ACT

CBL

ACT

CBL

- BMNT - - - ACT

ACT

BERM

ACT

CBL

- ACT

CBL

ACT

CBL

- BMNT - - - ACT

BLOCKING refers to ADMIN /ADMIN1, 2, 3, account suspension and trunk state

BMNT

LNATT refers to NOTSTSUL

NO Testing not possible in any of the listed states

ATE refers to ATE not blocked / CBL / MBL

Port Mod

ule

DIU LTG DLU BLOCK

ING

LNATT TU

mod

ule/

port

ATE ATE

:TM

ATE

:N

AT

CO

Table 3 Operating states that permit testing, 2 (Cont.)
http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/


13/46


14/46

14 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a677b

Introduction (IN)

Table Table 5shows the correlation between test equipment type, circuit type and LTU

type for test equipment connected to DLU.

1.2.4 Test Equipment Data

Additional data can be assigned to test equipment with command ENTR TEQDAT.

Parameter LAC must be specified whenever it is possible that subscriber directory

numbers without local area code or traffic discrimination code could arrive via the testequipment.

The value entered for parameter DLU defines which range of DLU the interfaces

MAOGT and MANTT are responsible for.

The value for the unlocking number UNLNO used by the responder TEMLE, DIGLP,

TESTSET and ETEAE is entered with command CR TEQ.. It can be modified with

command MOD TEQ.

1.2.5 Test Points for Test Traffic

Test equipment types TEMLE, TLFB, RBSI, WSTGRP and ETEAE are accessed

through the digit translator by means of test points rather than by means of code points.

ATEBRESP ATETM ATM

ATESELF ATETM ATM

CE TECONF V08, V10, V22, V23,

V31

DIGLP DIGLPBKT V04, V05

ETEAE ETEAE E02, F02, F03, N05,

V04

MACL CTEIC, CTEOG C07

RBSI RBS V09, V22, V31, V32

TEMLE TEMLEPRT, TETRR2, TETRL,TETRWL C03, C06, N07, N08,

V05

TLFB TLFBIC V03, V23

TLFI TLFIC, TLFOG V09, V22, V31, V32

Test equipment

at DLU port

Circuit type in DISP DLUPORT LTU type in DISP LTU

MANTT MTAC D30

MAOGT MTAC D30

MACONN MTAC D30

TESTSET SLCA D30

Table 5 Permitted circuit types and LTU types (DLU)

Table 4 Permitted circuit types and LTU types (LTG) (Cont.)
http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/


15/46

A30828-Y1160-U3-1-7620

15


Id:0900d805800a677b

Directory numbers are assigned to these types of test equipment with the command CR

TEPT.

For each directory number, a destination (command CR DEST) and a route (command

CR ROUTE) and a zone point (command CR ZOPT)must be created.

1.2.6 Thresholds for ATE and TU

The number of times that an automatic test will be repeated if a fault is found can be

interrogated with command DISP THR; (output parameter: TEREP). The default value

is 2, and it can be modified with ENTR THR:THRESH=TEREP, VALUE=.

If the ATEor TUreports a fault in a test object several times in succession, the self-test

is started automatically. The threshold at which the self-test is triggered can be defined

by the system operator and displayed with DISP THR; (output parameter FAILATE). The

default value is 10, and it can be modified with ENTR THR:

THRESH=FAILATE, VALUE=;.

1.2.7 Test Schedules

Schedules can be assigned to automatic test commands with parameter SCHED. The

schedules can be created with command ENTR TSTSCHEDand can be shared by

several test jobs. The schedules can be deleted with DEL TSTSCHED.

1.2.8 Test Results

The results of an automatic test job without schedule are output at the end of the test.

Intermediate results (not for a single test) during the test process are only output onrequest, using command DISP TSTRES.

The results of automatic test jobs with schedule are written to a cyclic history file or

archive file. This file is large enough to store the test results accumulated over one week

The commands DISP AENTRYand SEL AENTRYare used to read out the test results

from the archive file.

1.2.9 Workstations

Command CR WSTis used to create a workstation for the manual testing of trunks and

lines.

A workstation can be connected to the system at an LTGof type LTGB: Only one workstation can be connected in the exchange as PT0X. Its name is

specified in the 1st information unit of parameter TERMID. No other information

units may be entered for parameter TERMID.

If a workstation is connected via SMC, both information units of parameter TERMID

(processor and terminal number) must be entered.

The processor name must be created in the system (DISP PRO/CR PRO), other-

wise the command will be rejected.

Parameter WSTSN is used to assign a directory number to the workstation for use

in tests. An additional directory number can be assigned to the workstation for a

service handset with parameter DN. Both directory numbers must be pre-engi-

neered in the exchange and belong to the same local area (LAC).
http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


16/46

16 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a677b

Introduction (IN)

An originating mark can be specified with parameter ORIG1.

The command will be rejected if

the LTU specified as part of the LTG and LC is not created or

the LTG port data are implausible. To find out what circuit type was created with CRLTU, command DISP PORTcan be entered. The circuit type for a workstation must

be TPCPRT.

1.2.10 Workstation Test Port

Up to 8 test ports can be assigned to a workstation. The directory numbers DN of the

test ports must be defined in such a way that they cannot be accessed by ordinary sub-

scribers. The circuit type for a workstation test port must be TETPCPRT. This informa-

tion can be displayed with command DISP PORT.

1.2.11 Workstation GroupIn centers with numerous workstations, it is possible to form workstation groups dedi-

cated to different tasks (line testing/trunk testing).

A group can consist of a maximum of 6 workstations. A workstation can belong to

several groups at the same time (even all groups).

The parameter DIR defines the direction in which outputs will be routed, e.g. to a work-

station group in the exchange under test or to a workstation group in a maintenance

center.

Parameter FUNC defines the type of test for which the workstation group is responsible.

Parameter PRONAM specifies the processor via which the group can be accessed

(command DISP PRO/CR PRO).It must be ensured that the access to the group (CR

WSTGRP, parameter PRONAM) matches the access to the workstations in the group

(CR WSTparameter TERMID), otherwise the command will be rejected.

Connections to remote workstation groups are controlled by means of unsolicited mes-

sages. The assignment to workstation group and direction is made in accordance with

the function (18) and direction (13) by means of an individual data type. The values

of FUNC and DIR are defined in the parameters entered with MMLcommand CR

WSTGRP. Queues are provided for cases where a specific TLWSor the entire worksta-

tion group is busy. Incoming calls are rerouted to an announcement while waiting in the

queue. Parameter WP (waiting places) defines the maximum number of calls that are

allowed to wait be served per group. Calls in the queue that have not yet been presented

wait for a maximum of 5 minutes in the queue before being released automatically. If aqueue is full, all further calls to this workstation or the workstation group are rejected.

Commands are rejected if the specified workstation(s) has (have) not been created.

1.3 Administration of Test Objects

1.3.1 Subscriber Lines

Before testing, state-interrogation and display commands should be entered to verify

that the intended test object is in its normal configuration (ACT).
http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


17/46

A30828-Y1160-U3-1-7620

17


Id:0900d805800a677b

1.3.2 Administration of Thresholds for Line Testing

Command MOD LTESTTHRis used to define thresholds for the resistance, capaci-

tance, external voltage, loop resistance and pulse frequency and pulse duty ratio in sub-

scriber line and station testing.

Before a test is performed for the first time, the thresholds in the classes for SLMA:FPB,

SLMA:FPS, SLMD,... must be modified.

When a subscriber is created, threshold class 0 is automatically assigned.

The thresholds defined for each threshold class can be displayed with command

DISP LTESTTHR:THRCLA=x;.

Command DISP LTESTTHR:SPCVAL=Y; is used to display threshold classes for which

special values are entered.

1.3.3 Test ClassesA threshold class is assigned to a subscriber with command

MOD SLNACC:EQN=eqn, TESTCL=xx.

1.3.4 Trunks

Test data, test types and blockings are assigned to trunks with command ENTR TRDAT.

A test path number is assigned to incoming trunks with parameter TSTDAT. The test

path number is used to access the responder in remote-controlled trunk tests.

Parameter TSTTYP is used to assign trunk group test data to the trunk that were entered

with command ENTR TGTSTDAT. Up to 8 different test types can be entered for a trunk

group.

These data can be displayed with command DISP TRUNK.

1.3.5 Trunk Group Test Data

Test data are entered for national and international trunk groups with command ENTR

TGTSTDAT.

Parameter TSTCL defines a test class for the trunk. The test class represents the test

method and the type of responder in the distant exchange.

Test class 127 must be created for analog measurements on international trunks.

Test class 128 must be created for analog measurements and bit error ratio measure-ments on international trunks.

Test class 129 must be created for bit error ratio measurements (BERM) on international

trunks.

Parameter TSTMOD defines whether the trunks in the trunk group are to be tested

directly or by remote access.

If testing international trunks, the direct test option must be created.

Parameter TSTVAL is used to enter an index for overall loss on the trunk for test classes

1 to 126.

In the case of test classes 127 and 128, parameter TSTVAL assigns templates for level

and noise measurements. These templates are created with command CR TESTTHR.Parameter TSTVAL is not needed for test class 129.
http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/


18/46


19/46

A30828-Y1160-U3-1-7620

19


Id:0900d805800a677b

send identification tone

line supervision

1.4.2 Tests with the ATE:T

The automatic test equipment for trunks (ATE:T) is used to test analog PBXlines and

the tones and signals generated by the tone generator, and responders and special cir-

cuits.

To safeguard test results, the ATE:T has a self-test facility and an automatic calibration.

1.4.3 Automatic Tests with the TU

The test unit (TU) is used to test circuit modules, subscriber lines and terminals in the

DLU.

To perform tests, one TU must be created for each DLU. In addition, a translationfunction (TLFI) must be created in the LTGBto which the DLU is connected.

To safeguard test results, the TU has a self-test facility.

1.4.4 Tests with the Ringback Service

The ringback service (RBS) is used for the manual testing of analog and digital sub-

scriber lines and terminals. The tests are controlled from the remote end by a mainte-

nance technician at the customers premises. Tests of digital subscriber lines at BA and

PA ports are controlled by ringback service integrated (RBSI) programs.

1.4.5 ISDN Line TestsThe following functions are available for the automatic testing and fault clearance of

ISDNsubscriber lines:

1.4.6 SULIM

The subscriber line measuring system (SULIM) is used for the manual and automatic

testing of analog subscriber lines. The manual test functions are similar to those of the

integrated line workstation (LWS). The automatic tests (routine tests) with SULIM allow

line parameters to be checked.

The start and end times for a routine test are determined by a test schedule. The lines

to be tested are stored in directory number tables.

Activate layer 1 TEST ISUB, TEST SUB

Loop test at BA TEST LOOPBA

Loop test at PA TEST PA

Running digital sum (RDS) measurement START RDSMEAS

BAperformance measurement ACT BAPERF

PDCperformance measurement ACT PDCFEA
http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/


20/46

20 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a677b

Introduction (IN)

1.5 Trunk Testing

1.5.1 Testing with the Trunk Workstation

The integrated trunk workstation (TWS) for the manual testing of trunks is used for fault

location, for support in fault clearance and for testing trunks before they are placed in

service (restored to service).

At the trunk workstation, it is possible to set up calls, receive calls and start manually

controlled tests and measurements. Administrative tasks and status requests for trunks

are also possible here.

To carry out test functions, the following must be created:

conference equipment

ATE:TM / ATE:N/ ATCO

workstation test port

headset port

During manual trunk testing and fault clearance, the following can be measured:

test tones

composite level, unweighted

composite level, weighted

level monitoring with specified limit

frequency spectra

MFC or

single frequency with tone pulse evaluation

The announcement workstation (AWS) application provides a convenient user interface

for connections to trunks, announcements or tone generator channels.

1.5.2 Tests with the ATE:T

The automatic test equipment for trunks (ATE:T) is used to test trunk circuits, incoming

trunks and outgoing trunks in conjunction with a responder.

The ATE:T can also be used to test analog PBXlines, the tones and signals generated

by the tone generator, and responders and special circuits.

To safeguard test results, the ATE:T has a self-test facility.

1.5.3 Tests with the ATE:TM / ATE:N/ ATCOThe automatic test equipment for transmission measuring (ATE:TM/ ATE:N/ ATCO) is

used for

manual testing of trunks with the TWS

automatic testing of international trunks TEST INTLTRK

bit error ratio measurements on trunks with the assistance of a loopback at the

remote endACT BERM
http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/http://a200.pdf/


21/46


22/46

22 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a676c

Tasklist (TL)

2 Tasklist (TL)

gDisplay commands are only specified in the procedures if they are absolutely nec-essary. As a rule, display commands are not necessary to verify that a commandhas been executed. It is already obvious from the command acknowledgement

issued by the system whether the input command was correctly executed (see also

Operator Guidelines OGL). Should it be necessary for administrative reasons to

receive an acknow edgement of the executed work in addition to the run listing, the

content of the database can be displayed with the relevant commands (see CML)

before and after, or only after, each task.In each task, only those parameters and

identifiers are specified that are typical for the task in hand.

2.1 Test Administration

2.1.1 Operating statesDisplay port operating state .......................................................b STAT PORTDisplay trunk operating state ...................................................b STAT TRUNKDisplay CCGoperating state .......................................................b STAT CCGDisplay LTGoperating state .........................................................b STAT LTGDisplay DIUoperating state ...........................................................b STAT DIUDisplay MBoperating state.............................................................b STAT MBDisplay SNoperating state .............................................................b STAT SNDisplay DLUoperating state.........................................................b STAT DLUDisplay DLU module operating state ....................................b STAT DLUMODDisplay DLU port operating state........................................b STAT DLUPORTConfigure port...............................................................................b CONF PORTConfigure LTG.................................................................................b CONF LTGConfigure DIU...................................................................................b CONF DIUConfigure DLU.................................................................................b CONF DLUConfigure DLU module............................................................b CONF DLUMODConfigure DLU port................................................................b CONF DLUPORT

2.1.2 Display operating states of test equipmentDisplay operating state of automatic test equipment ATE

using: TGNO=x, TYPE=ATE ...........................................b STAT TEQDisplay operating state of director for bit error ratio measurementusing: TGNO=x, TYPE=ATEBDIR ...................................b STAT TEQ

DIsplay operating state of responder for bit error ratio measurement

using: TGNO=x, TYPE=ATEBRESP ...............................b STAT TEQDisplayoperating state of ATE operating as director in trunk test

using: TGNO=x, TYPE=ATEDIR .....................................b STAT TEQDisplay operating state of ATE:TM / ATE:N/ ATCO

using: TGNO=x, TYPE=ATEMAN....................................b STAT TEQDisplayoperating state of ATE operating as responder in trunk test

using: TGNO=x, TYPE=ATEDIR .....................................b STAT TEQDisplay operating state of ATE:TM / ATE:N/ ATCO self-test

using: TGNO=x, TYPE=ATESELF...................................b STAT TEQ
http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


23/46

A30828-Y1160-U3-1-7620

23

OMN:TE-AD Tasklist (TL)

Id:0900d805800a676c

Display operating state of conference equipment

using: TGNO=x, TYPE=CE..............................................b STAT TEQDisplay operating state of digital loopback function for bit error

ratio measurement using: TGNO=x, TYPE=DIGLP.........b STAT TEQDisplay operating state of end-to-end answer equipment for

trunk test using: TGNO=x, TYPE=ETEAE.......................b STAT TEQDisplay operating state of metallic test access interface from

test equipment to test object using: TGNO=x, TYPE=MANTT ................

b STAT TEQDisplay operating state of metallic test access interface from

test object to test equipment using: TGNO=x, TYPE=MAOGT ...............

b STAT TEQDisplay operating state of ringback service in LTGB

using: TGNO=x, TYPE=RBSI ..........................................b STAT TEQDisplay operating state of testset (test phone)

using: TGNO=x, TYPE=TESTSET ..................................b STAT TEQDisplay operating state of responder for trunk test

using: TGNO=x, TYPE=TEMLE.......................................b STAT TEQDisplay operating state of TLFB

using: TGNO=x, TYPE=TLFB..........................................b STAT TEQDisplay operating state of TLFI

using: TGNO=x, TYPE=TLFI ...........................................b STAT TEQDisplayoperating state of test unit in DLU

using: DLU=dluno, LC=0-11-0

using: DLU=dluno, LC=0-12-0

using: DLU=dluno, LC=0-13-0 ...............................b STAT DLUPORT

Display operating state of MTAusing: DLU=dluno, LC=1-13-0 ...............................b STAT DLUPORTDisplay operating state of LTA

using: DLU=dluno, LC=1-14-0 ...............................b STAT DLUPORT

2.1.3 Test equipmentDisplay test equipment ..................................................................b DISP TEQCreate test equipment .....................................................................b CR TEQModify test equipment ..................................................................b MOD TEQCancel test equipment ...................................................................b CAN TEQCreate testset (test phone) in DLU ...........................................................TP-002

Cancel testset (test phone) .......................................................................TP-003Create ringback service ............................................................................TP-004

2.1.4 Test equipment dataDisplay test equipment data ...................................................b DISP TEQDATEnter test equipment data .................................................b ENTR TEQDATCancel test equipment data ...................................................b CAN TEQDAT

2.1.5 Thresholds for ATE/TUEnter thresholds for ATE/TU ....................................................b ENTR THRDisplay thresholds for ATE/TU ......................................................

bDISP THR
http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


24/46


25/46

A30828-Y1160-U3-1-7620

25

OMN:TE-AD Tasklist (TL)

Id:0900d805800a676c

Display PBX lines .....................................................................b DISP PBXLNDisplay operating state of layer 1 ..........................................b STAT ILAYER1Display operating state of basic access ..........................................b STAT BADisplay DLUports with circuit variants ................................b DISP DLUPORTDisplay selected DLU port data .............................................b SEL DLUPORTDisplay FCS count.........................................................................b DISP FCSDisplay RDS measurement count.......................................b DISP RDSMEASDisplay count of transmitted and errored frames at PA..........b DISP PASTATDisplay layer-2 errors and bit error ratios for subscriber lines

and PBX lines at PA ................................................b DISP BAFAULTDisplay intermediate results of performance measurement ...b DISP BAPERFDisplay fault conditions recorded for PBXs

with PA.....................................................................b DISP PAFAULTDisplay performance data for PDC ......................................b DISP PDCPERFDisplay activation status of the feature for collecting and

storing PDC performance data ..................................b DISP PDCFEADisplay PA channel status.................................................b DISP PACHSTATEnter line maintenance blocking ..........................................b ENTR LMBLKCancel line maintenance blocking ............................................b CAN LMBLK

2.2.2 Administration of thresholds for line testingDisplay thresholds for each threshold class .......................b DISP LTESTTHRModify thresholds for each threshold class .......................b MOD LTESTTHR

2.2.3 Test classes for subscriber lines

Modify test class ....................................................................b MOD SLNACC

2.2.4 TrunksDisplay trunk operating state...................................................b STAT TRUNKEnter trunk maintenance blocking ........................................b ENTR TMBLKCancel trunk maintenance blocking ..........................................b CAN TMBLK

2.2.5 Trunk dataEnter trunk data....................................................................b ENTR TRDATCancel trunk data......................................................................b CAN TRDAT

2.2.6 Trunk group test dataDisplay trunk group test data .............................................b DISP TGTSTDATEnter trunk group test data............................................b ENTR TGTSTDATModify trunk group test data.............................................b MOD TGTSTDATCancel trunk group test data..............................................b CAN TGTSTDAT

2.2.7 Administration of thresholds for international trunk testingDisplay test thresholds .........................................................b DISP TESTTHRCreate test threshold ..............................................................b CR TESTTHRModify test threshold ...........................................................b MOD TESTTHRCancel test threshold ............................................................b CAN TESTTHR
http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


26/46


27/46

A30828-Y1160-U3-1-7620

27

OMN:TE-AD TP-002 - Create testset at DLU port

Id:0900d8058018debb

4 TP-002 - Create testset at DLU portThe unlock number (UNLNO) is entered in command CR TEQ/ MOD TEQ.

1 Create testsetb CR TEQ:TGNO=tgno, TYPE=TESTSET, EQN=eqn;

A unique symbolic name must be assigned to the TESTSET in parameter TGNO.

2 Create destination for testsetIf required

b CR DEST:DEST=TESTSET;

3 Create route for testsetIf required

b CR ROUTE:DEST=TESTSET, TGNO=tgno, SSDI=15, EOS=SIGN,ROUTE=route;

4 Create test point for testsetIf required

b CR TEPT:CODE=code, DEST=TESTSET;

5 Create zone point for testsetIf required

b CR ZOPT:CODE=code, ZOCHA=NOPULSE;

6 Configure DLU portb CONF DLUPORT:DLU=dlu, LC=lc, OST=MBL;

b CONF DLUPORT:DLU=dlu, LC=lc, OST=ACT;

7 END
http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


28/46

28 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a6779

TP-003 - Cancel testset

5 TP-003 - Cancel testsetThe cancel command will be rejected if the routing table still contains a reference to the

testset and if this testset is the only one in the trunk group. If the route is a primary route,

the associated test point must be canceled first.

1 Display testsetb DISP TEQ:TGNO=X, TYPE=TESTSET;command repetition

TEST EQUIPMENT DATA

TGNO TYPE EQN / LTG-LC LTGMODE DIGITS LTGMIN MU UNL OR1

BLK LAC LTGMAX OR2

------+--------+-------------+-------------+--------+------+---+---+----

@##### @####### @############ @############ @####### @### @ @# @###

2 Block testsetb MOD TEQ:TGNO=tgno, EQN=eqn, BLK=ADMIN/;

3 Cancel zone point for testsetb CAN ZOPT:CODE=code, INCEPT=UNOBDE0;

4 Cancel test point for testsetb CAN TEPT:CODE=code, INCEPT=incept;

5 Cancel route for testsetb CAN ROUTE:DEST=TESTSET, TGNO=tgno, ROUTE=route;

6 Cancel destination for testsetb CAN DEST:DEST=dest;

7 Cancel testsetb CAN TEQ:TGNO=tgno, EQN=eqn;

8 END
http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/


29/46

A30828-Y1160-U3-1-7620

29

OMN:TE-AD TP-004 - Create ringback service

Id:0900d805800a6778

6 TP-004 - Create ringback serviceCreate ringback service for analog and digital DLUsubscribers.

1 Display LTUb DISP LTU:LTG=ltg;command repetition

LTG LTU TYPE APPLIC MODVAR

-------+----+-----+-------+---------------------------------------

@### @ V09 @##### @######################################

2 Decision blockDoes this LTG contain an LTU of type V09?

Yesh......... 4Noh ......... 3

3 Create LTUAn LTU of TYPE V09 must be created for TLFI and RBSI. LTU 4, 5 or 6 can be selected.

b CR LTU:LTG=ltg, LTU=ltu, TYPE=V09;

4 Display port datab DISP PORT:LTG=ltg, LC=lc;command repetition

LTG = @##### LC = @### LCTYPE = TLFIC LCVAR = @ TYPE = @#######

LTG = @##### LC = @### LCTYPE = TLFOG LCVAR = @ TYPE = @#######

5 Decision blockIs a TLFI created?

Yesh......... 7Noh ......... 6

6 Create TLFIb CR TEQ:TGNO=tgno, TYPE=TLFI, LTG=ltg, LC=lc;The TLFI can be created at four LTU ports: 2, 10, 18, 26. The TLFI occupies two suc-

cessive ports. The first port must be specified, the second is assigned automatically.

7 Create RBSIb CR TEQ:TGNO=tgno, TYPE=RBSI, LTG=ltg, LC=lc;The RBSI can be created at four LTU ports: 4,12, 20, 28.
http://a200.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://a200.pdf/


30/46

30 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a6778

TP-004 - Create ringback service

8 Display destination for RBSIb DISP DEST:DEST=dest;

9 Decision blockIs a destination created for RBSI?

Yesh......... 11Noh.......... 10

10 Create destination for RBSIb CR DEST:DEST=dest;

11 Display route for RBSIb DISP ROUTE:DEST=dest;

12 Decision blockIs a route created for RBSI?

Yesh......... 15Noh.......... 13

13 Create route for RBSIb CR ROUTE:DEST=dest, TGNO=tgno, SSDI=7, EOS=SIGN, ROUTE=route;

14 Display testpoint for RBSIb DISP TEPT:DEST=dest;

15 Decision blockIs a test point created for RBSI ?

Yesh......... 17Noh.......... 16

16 Create test point for RBSIb CR TEPT:CODE=code, DEST=dest;

17 Create exchange identifierb MOD CALLPOPT:RBSIN=rbsin;Up to 8 digits can be defined an an identifier with parameter RBSIN.
http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


31/46

A30828-Y1160-U3-1-7620

31

OMN:TE-AD TP-004 - Create ringback service

Id:0900d805800a6778

18 END


32/46

32 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a6777

TP-011 - Create SMC as TLWS workstation connectedvia NetM

7 TP-011 - Create SMC as TLWS workstation

connected via NetM

A Subscriber Maintenance Commander (SMC) can be created as a workstation for lineand trunk testing. This workstation can be connected to an LTGof type LTGB. It is con-

nected to the system via the NetManager (NetM).

1 Create intercept tonesb CR INC:INCEPT=TESTWAIT, TONE=INFOTONE;

b CR INC:INCEPT=NOTESTOP, TONE=SUBBUSY;

2 Create directory number volume for TLWSb CR DN:DN=dn&&dn, LAC=lac;

3 Create code point for TLWSb CR CPT:CODE=code, TRATYP=CPTDN, LAC=lac;

4 Create zone point for TLWSb CR ZOPT:CODE=code, ZOCHA=NOPULSE;

5 Create LTU for TLWSAn LTU of TYPE V11 or of TYPE = V02must be created for the workstation.

b CR LTU:LTG=ltg, LTU=ltu, TYPE=type;

6 Create workstation for TLWS userid"CSname" is the processorname created for the NetM SMC CS in CP database. sta-

tionno is the station number which is assigned to one NT userid (via TLWS administra-

tion program.)

b CR WST:WST=wst, TERMID=CSname-stationno, LAC=lac, WSTSN=wstsn,DN=dn, LTG=ltg, LC=lc, WP=8, APPLID=DIALG;

7 Create WST test port for TLWSUp to 8 test ports can be created per workstation.

b CR WSTPRT:WST=wst, NO=no, LTG=ltg, LC=lc, LAC=lac, DN=dn;

8 Create destination for TLWS groupb CR DEST:DEST=dest;
http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/


33/46

A30828-Y1160-U3-1-7620

33

OMN:TE-AD TP-011 - Create SMC as TLWS workstation connectedvia NetM

Id:0900d805800a6777

9 Create TLWS groupFor trunk test/maintenance using FUNC=TRKMNT1

For line test/maintenance using FUNC=LNMNT1b CR WSTGRP:WSTGRP=wstgrp, DIR=DIR1, FUNC=func, WP=4, WST=PC1X;

10 Create route for TLWS groupb CR ROUTE:TGNO=tgno, DEST=dest, ROUTE=1, SSDI=4, EOS=SIGN;

11 Create test point for TLWS groupb CR TEPT:CODE=code, DEST=dest, LAC=lac;

12 Create zone point for TLWS groupb CR ZOPT:CODE=code, ZOCHA=NOPULSE;

13 END
http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


34/46

34 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a6776

TP-012 - Create OMT as TLWS workstation

8 TP-012 - Create OMT as TLWS workstationAn Operation and Maintenance Terminal (OMT) can be created as a workstation for line

and trunk testing. This workstation can be connected to an LTGof type LTGB.

gOnly one workstation can be created per switch for the local OMT

1 Create intercept tonesb CR INC:INCEPT=TESTWAIT, TONE=INFOTONE;

b CR INC:INCEPT=NOTESTOP, TONE=SUBBUSY;

2 Create directory number volume for TLWS

b CR DN:DN=dn&&dn, LAC=lac;

3 Create code point for TLWSb CR CPT:CODE=code, TRATYP=CPTDN, LAC=lac;

4 Create zone point for TLWSb CR ZOPT:CODE=code, ZOCHA=NOPULSE;

5 Create LTU for TLWSAn LTU of TYPE V11 or of TYPE = V02must be created for the workstation.

b CR LTU:LTG=ltg, LTU=ltu, TYPE=type;

6 Create workstation for TLWS useridThe terminal identification (TERMID) is equal to the local processor name (PRO-

TYP=SSP) which must already exist in the system.

b CR WST:WST=wst, TERMID=processor name, LAC=lac, WSTSN=wstsn,DN=dn, LTG=ltg, LC=lc, WP=8;

7 Create WST test port for TLWSUp to 8 test ports can be created per workstation.

b CR WSTPRT:WST=wst, NO=no, LTG=ltg, LC=lc, LAC=lac, DN=dn;

8 Create destination for TLWS groupb CR DEST:DEST=dest;
http://a200.pdf/http://a200.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://a200.pdf/http://a200.pdf/


35/46

A30828-Y1160-U3-1-7620

35

OMN:TE-AD TP-012 - Create OMT as TLWS workstation

Id:0900d805800a6776

9 Create TLWS groupFor trunk test/maintenance using FUNC=TRKMNT1

For line test/maintenance using FUNC=LNMNT1b CR WSTGRP:WSTGRP=wstgrp, DIR=DIR1, FUNC=func, WP=4, WST=PC1X;

10 Create route for TLWS groupb CR ROUTE:TGNO=tgno, DEST=dest, ROUTE=1, SSDI=4, EOS=SIGN;

11 Create test point for TLWS groupb CR TEPT:CODE=code, DEST=dest, LAC=lac;

12 Create zone point for TLWS groupb CR ZOPT:CODE=code, ZOCHA=NOPULSE;

13 END


36/46

36 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a6775

TP-015 - Cancel workstation

9 TP-015 - Cancel workstationA workstation can only be canceled when the following conditions are met:

The workstation must not be active.

There must be no test ports assigned to the workstation.

The workstation must not belong to a workstation group.

1 Check status of workstationb STAT WST:WST=wst;command repetition

STATUS OF WORK STATION

WSTNAME:@##### HEADSET STATE:@############# INCOMING CALLS:@########

NO OF WAITING CALLS: @#

T E S T O B J E C T

EQN

NO STAT MODE DIR CALLTYPE DN TOGCH(LTG-LC) TGNO LNO CIC

--+----+-----+---+-----------+--------+-------------+------+-----+------

@# @### @#### @## @########## @####### @############ @##### @#### @#####

2 Decision blockIs the headset state DEACTIVATED?

Yesh......... 4Noh.......... 3

3 Deactivate workstationb DACT WST;

4 Display workstation test portb DISP WSTPRT:WST=wst;command repetition

DATA OF WORK STATION TEST PORT

WST NO LTG LC LAC DN BLK ORIG1

-------+-+-------+-----+------+--------+--------+------

@##### @ @##### @### @##### @####### @##### @###

5 Decision blockAre workstation test ports still assigned?

Yesh......... 6Noh.......... 7
http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/


37/46

A30828-Y1160-U3-1-7620

37

OMN:TE-AD TP-015 - Cancel workstation

Id:0900d805800a6775

6 Cancel workstation test portb CAN WSTPRT:WST=wst, NO=no;

7 Display workstation groupb DISP WSTGRP:WSTGRP=X;command repetition

DATA OF WORK STATION GROUP

WSTGRP DIR FUNC PRONAM APPLID WP BLK WST

------+----+-------+--------+------+--+-------+-------

@##### @### @###### @####### @#### @# @##### @#####

8 Decision blockIs the workstation assigned to a workstation group?

Yesh......... 9Noh ......... 10

9 Modify workstation groupb MOD WSTGRP:WSTGRP=wstgrp, WST= /wst;

10 Cancel workstationb CAN WST:WST=wst;

11 END
http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


38/46

38 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a6774

TP-016 - Modify worktstation data

10 TP-016 - Modify worktstation dataThe command MOD WSTcan be used to modify the data stored for workstations.

1 Display workstation datab DISP WST:WST=X;command repetition

WORK STATION DATA

WST TERMID APPLID LTG LC WP COS BLK ORIG1

------+-------------+------+-------+----+--+---------+------+-----

@##### @############ @#### @###### @### @ @######## @##### @###

WORK STATION DATA

WST LAC WSTSN DN TAPRT

------+------+--------+--------+-----------

@##### @##### @####### @####### @##########

2 Modify workstation datab MOD WST:WST=wst, TERMID=termid, APPLID=applid, DN=dn, WP=wp,

ORIG1=orig1, TAPRT=taprt, BLK=blk;

3 END
http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


39/46

A30828-Y1160-U3-1-7620

39

OMN:TE-AD TP-017 - Modify workstation group data

Id:0900d805800a6773

11 TP-017 - Modify workstation group dataThe command MOD WSTGRPcan be used to modify the data stored for workstation

groups.

1 Display workstation group datab DISP WSTGRP:WSTGRP=X;command repetition

DATA OF WORK STATION GROUP

WSTGRP DIR FUNC PRONAM APPLID WP BLK WST

------+----+-------+--------+------+--+-------+-------

@##### @### @###### @####### @#### @# @##### @#####

2 Modify workstation group datab MOD WSTGRP:WSTGRP=wstgrp, DIR=dir, FUNC=func, PRONAM=pronam,

APPLID=applid, WST=wst, WP=wp, BLK=blk;

3 END
http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


40/46


41/46

A30828-Y1160-U3-1-7620

41

OMN:TE-AD TP-018 - Cancel workstation group

Id:0900d805800a6772

7 Cancel workstation groupb CAN WSTGRP:WSTGRP=wstgrp;

8 END
http://cmlexch.pdf/http://cmlexch.pdf/


42/46

42 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d805800a6771

TP-019 - Cancel workstation test port

13 TP-019 - Cancel workstation test portCommand CAN WSTPRTcancels a test port of a workstation. The specified test port is

only canceled if its transient operating state allows this.

The directory number DN of a canceled test port is redirected to NU tone (number unob-

tainable).

1 Display workstation test portsb STAT WST:WST=wst;command repetition

STATUS OF WORK STATION

WSTNAME:@##### HEADSET STATE:@############# INCOMING CALLS:@########

NO OF WAITING CALLS: @#

T E S T O B J E C T

EQN

NO STAT MODE DIR CALLTYPE DN TOGCH(LTG-LC) TGNO LNO CIC

--+----+-----+---+-----------+--------+-------------+------+-----+------

@# @### @#### @## @########## @####### @############ @##### @#### @#####

2 Cancel workstation portb CAN WSTPRT:WST=wst, NO=no;

3 END
http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/


43/46

A30828-Y1160-U3-1-7620

43

OMN:TE-AD TP-021 - Display intermediate test results

Id:0900d805800a6770

14 TP-021 - Display intermediate test resultsIf you do not know the job number, enter command DISP JOBto obtain a list of general

job data.

Look for the command code of the test job in this list. The job number listed for the

command code must be specified in command DISP TSTRES.

1 Display general job dataIf required

b DISP JOB:JN=X;

2 Display intermediate test resultsb DISP TSTRES:JN=jn;

3 END


44/46

44 A30828-Y1160-U3-1-7620

OMN:TE-AD

Id:0900d8058018dee5

TP-022 - Display test job

15 TP-022 - Display test jobIf you do not know the job number, enter command DISP JOBto obtain a list of general

job data.

Look for the command code of the test job in this list. The job number listed for the

command code must be specified in command DISP TSTJOB.

1 Display general job dataIf required

b DISP JOB:JN=X;

2 Display test jobb DISP TSTJOB:JN=jn;

3 END


45/46

A30828-Y1160-U3-1-7620

45

OMN:TE-AD TP-030 - Display test results from archive file

Id:0900d8058018df0c

16 TP-030 - Display test results from archive file

1 Decision blockDo you know the name of the archive file containing the test results?

Yesh......... 3Noh ......... 2

2 Display archive filesb DISP AFILE:AFILE=X;command repetition

AFILE SIZE TYPE THRU THRD THRF COMMENT------------------+--------+-------+-----+-----+---------+--------------

@################ @###### @##### @## @## @###### @#############

Archive files (AFILE) containing test results are usually named TESTRES or RT.TES-

TRES.

3 Display archive file entriesb DISP AENTRY:AFILE=afile, TOC=YES;command repetition

AENTRY DATE TIME JOBNO CONTEXT FORMAT ALPRIO

------------------------------------------------------------------------

@#### @####### @####### @### @################## @#######

4 Select test results from the archive fileb SEL AENTRY:AFILE=afile, DATE=date, JN=jn, MSG=msg;

By entering parameter DATE, you can define the dates for which test results are

output.

By entering parameter JN, you can output test results of a specific test job.

A By entering parameter MSG (combination of test command and output masknumber) you can output individual results of a test job.

h ......... 5

5 Inputs for parameter MSGTest results Statistical

report

Busy and

inacces-

sible test

objects

Error

messages

Command

repetition

TEST LIC -6524 -6540 -6194 -6513

TEST LTGPOS -6529 -6540 -6194 -6513

TEST CTYPE -6529 -6540 -6194 -6513
http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/http://omlexch.pdf/http://cmlexch.pdf/


46/46

OMN:TE-ADTP-030 - Display test results from archive file

6 END

TEST TC -6538 -6540 -6535 -6194 -6513

TEST DLULC -6491 -4027 -3891 -4010 -2795

TEST ISUB -6511 -4024 -3893 -4010 -2795

TEST SLC -6493 (DLU) -4027 -3891 -4010

(DLU)

TEST SUB -6495 -6511 -3893

(DLU)

-4010

Test

results

Statistical

report

List of faulty

responders

List of

responder

faults

Error

messa

ges

Comma

nd repe-

tition

TEST PBXLN -6516 -6540 -6474 -6112 -6194 -6513

TEST TRUNK -6482 -6540 -6474 -6112 -6194 -6513

TEST INTLTRK -6477 -6540 -6474 -6112 -6194 -6513
http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/http://cmlexch.pdf/

Date post:	03-Jun-2018
Category:	Documents
Upload:	peydayesh
View:	234 times
Download:	0 times

Omn Te Ad Mobile

Documents