OmniTronix Specification Sheet for Model(s): FL2T18-36M and FX2T18-36M

Description: Micro Controlled, MultiWatt, Wide Input Voltage Range, HF-Electronic Ballast This Ballast will operate the following Lamps: F18T8, F30T8, F36T8, TC-L18W, TC-L24W, TC-L36W, TC-L40W, TC-F24W, TC-F36W, T5c 22W, T5c 40W, F24T5, F39T5, TC-D/TC-T26W, TC-T32W, TC-T42W, and TC-T57W

Electrical Data (for 230V Application) Input Voltage: 120V ±10% @ 50-60Hz

1 Lamp Lamp Wattage / Type F18T8 F30T8 F36T8 TC-L18 TC-L24 TC-L36 F24T5 F39T5 T5c22 Input Wattage 19.8 - 34 17.9 25.2 33.3 23.6 38.7 23 Line Current mA 92 - 154 85 116 150 110 172 110 Power Factor 0.92 - 0.95 0.91 0.94 0.96 0.94 0.96 0.94 Ballast Factor 0.95 - 0.90 0.83 0.93 0.86 0.87 0.92 0.96 Efficiency Factor 0.87 - 0.95 0.82 0.90 0.93 0.89 0.93 0.90 THD %A 19 - 15 20 17 15 17 13 18 Current Crest Factor 1.48 - 1.4 1.4 1.4 1.4 1.48 1.4 1.4

2 Lamps Lamp Wattage / Type F18T8 F30T8 F36T8 TC-L18 TC-L24 TC-L36 F24T5 F39T5 T5c22 Input Wattage 38 - 65 33.5 50.1 62.4 46 70 46 Line Current mA 179 - 288 151 231 275 204 310 221 Power Factor 0.95 - 0.98 0.96 0.97 0.98 0.97 0.98 0.95 Ballast Factor 0.95 - 0.88 0.84 0.93 0.85 0.83 0.86 0.96 Efficiency Factor 0.94 - 0.95 0.90 0.90 0.96 0.90 0.95 0.90 THD %A 15 - 9.5 15 12 9.6 12 9.2 10 Current Crest Factor 1.4 - 1.3 1.4 1.4 1.4 1.49 1.3 1.4

EM / RFI Compliance EN50147-1, EN61000-3-2, FCC Part 18-A Sound Rating “A” Ballast Type Digital Preheat Rapid Start (Warmstart) Immunity EN61547, ANSI C8211-1993 Input / Protection Electronic Fuse Output / Protection YES, Short and Open Circuit Min. Starting Temp. -25°C (0°F) *See note on reverse side Max. Case Temp. +75°C (167F) Energy Star / E.E. Class -- / Energy Efficiency Class A2 Approvals / Class CSAus, cULus, UL listed, ENEC05, CE, Class “P”, 1 Outdoor

Wiring Diagram

Note: Ballast case ground terminal must be grounded Use only within an electrical enclosure TYPE 1 OUTDOOR CLASS P

OmniTronix Engineering extends limited warranty only to the original purchaser or to the first user for the period of 3 years from date of manufacture as indicated by the date code stamped on each product and when properly installed and under normal conditions of use. Due to a program of continuous improvement, OmniTronix Engineering reserves the right to make any variation in design or construction to the equipment described. Data is based on tests performed by OmniTronix Engineering in a controlled environment and representative of relative performance. Actual performance may vary depending on operating conditions.