Operating handbook Feeder Ironer Folder & Stacker...

01102046/GB08.2014

Operating handbook

Feeder Ironer Folder& Stacker

IC44819FFS – IC44825FFS – IC44832FFS

original language

.

10

2714INSTRUCTIONHANDBOOK

01102046

Notice Date Page

The manufacturer reserves the right to modify construction and equipment characteristics.

Pages/Chapters Pages/Chapters

Easy

sta

rt

Appendices Conversion measurement units ............... 1/10 Washing symbols ..................................... 2/10

0. Table of contents

General instructions Preliminary instructions ............................. 1/1 General ..................................................... 1/2 Precautions for use ................................... 1/3

Machine operation Additional instructions ............................... 1/4 Machine starting ....................................... 2/4 The "Move back" key ................................ 2/4 Setting out ................................................. 2/4 Diamms mode ........................................... 3/4 Manual mode ............................................ 4/4 Using the handle........................................4/4

Folds table choice.. ................................... 5/4 Stopping .................................................... 6/4 Cooling ...................................................... 7/4 Power is back ........................................... 8/4 Emergency stop ........................................ 9/4 Run a program ......................................... 10/4 Energy saving mode ................................ 11/4

Advanced use Basic settings ............................................ 1/5 Set folds table ........................................... 3/5 Advanced settings .................................... 4/5 To select "statistics" .................................. 6/5 Daily statistics ........................................... 6/5 Clock adjustment ...................................... 7/5 Password change ..................................... 8/5 Language setting ...................................... 9/5 Programming ........................................... 10/5 Create wash program .............................. 11/5 Program edition ....................................... 12/5 Modify a program ..................................... 14/5 Delete a program ..................................... 18/5

Additional information of using Diagram of Electrolux ITS menus ............. 1/6

Safety Safety ........................................................ 1/7

Operating incidents Order of service ........................................ 1/8

Maintenance Preventive maintenance ........................... 1/9 Lubrifi cation table ...................................... 6/9 Replacing ironing bands ........................... 7/9

0708 20 INSTRUCTION

HANDBOOK

01102046

Notice Date Page

This page is left blank on purpose.

0. Table of contents

11

0508INSTRUCTION HANDBOOK

01102046

Notice Date Page

Preliminary instructionsBefore any use, it is compulsory to read the instruction handbook.

Users must have learnt how the machine operates.

The identification plate is placed on electric cabinet side of the machine.

In order to prevent any risk of fire or explosion, flammable products should never be used to clean the machine.

Any repair or maintenance intervention should be carried out by qualified personnel only.

Installation and putting into service must be carried out by trained staff.

N.B. : this machine has no part made of asbestos.

Explanation of graphic symbols

A flash of lightning with an arrow at its end displayed inside an equilateral triangle, warns the user about the presence of uninsulated "dangerous current" sufficient in intensity to cause electrocution.

An exclamation mark inside an equilateral triangle offers the user important advice about usage, servicing and hazardous conditions.

This symbol warns the user that there are mechanisms inside the machine which can be dangerous. The protective housing must be in place during use.

This symbol warns the user of the presence of high temperatures which could cause severe burns. Some surfaces can reach close to 200 °C (392 °F).

1. Preliminary instructions

0508 21 INSTRUCTION

HANDBOOK

01102046

Notice Date Page 1. Preliminary instructions

You should have found an instruction handbook and keys to open the machine casings, and a maintenance poster to display in your laundry, inside your machine.

Depending on its destination, the dryer ironer is delivered bare or may be placed on a transport pallet and/or packed with plastic film. In some cases, it may be delivered in maritime packing (wood crate).

Please refer to the handling chapter in this instruction handbook for a description of handling operations.

This machine should be installed in conformance to the health and safety regulations, and only used in a sufficiently aerated area. Check the instructions before installing or using the machine.

The use and handling of chemical products such as detergent, chlorine, acids, antiliming agents etc... may create hazards for health and environment ; the following precautions should be taken.

- Do not breathe the dusts or steam.- Avoid contact with skin or eyes (may cause burns).- In case of important spillage, wear a protecting mask, gloves, and eye protectors.- Handle with care.- Consult the use and first aid advice on the packings.- Do not dispose pure products in the environment.

The machine can work without the protective casing when the electric supply is not cut off.Interlock the main isolating switch with a padlock.Close the steam inlet valves.

0508 31INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Easy

sta

rtEasy start

Easy startFor a quick drive of the machine, an insert «Easy start» surrounds some pages.

This allows you to realize yours first ironing programs in a quick time.

1. Preliminary instructions

0408 41 INSTRUCTION

HANDBOOK

01102046

Notice Date Page 1. Preliminary instructions

Identification plate

D1582

0608 12INSTRUCTION

HANDBOOK

01102046

Notice Date Page

General instructionsThe machines described in this hanbook have a ironing capacity of 190, 250, 320 cm wide depending on the type. They are available with steam, electric, gas or thermal fluide heating.

They carry out five different fonctions with a single operator; the space required is very similar to the standard ironer’s.

The ironing speed is adjustable as a function of the density (weight/m2) and humidity of the washing.

The temperature of the ironing cylinder can also be adjusted by a thermostat (except for steam; in this case, the temperature depends on the steam pressure).

The ironing parameters that you have selected are permanently checked by a microprocessor.

These parameters are displayed in real time on a tactile screen in front of the operator.

The feeding of the linen is completely automatized and includes smoothing; a single operator is required; the folding of the items is calculated for each item fed.

Several piles of linen can be stored in the stacker with centering and numbering of the folded items.

The machine can be used like a standard ironer with or without the automatic feeding.

ELECTROLUX ITS

Identificationplate

2. General

0608 22

D1582

INSTRUCTION HANDBOOK

01102046

Notice Date Page 2. General

This dryer ironer is controlled by a microprocessor-based program control unit placed on the loading side. There are many advantages to this equipment, including :

• Folding adjustment is controlled with great precision and flexibility.

• The large display screen means that detailed information on iron programs, machine status and operations, dry speeds and temperatures can be accessed in plain language.

• It is possible for the user to create new iron programs, and to adapt programs with great precision, on the basis of experience and to suit various types of textile, degrees of moisture etc.

• A very high level of machine safety through continuous monitoring and built-in safety interlocks.

• Great flexibility during program operation :

- easy change from DIAMMS mode till MANUAL mode and inversely;

- the user can change temperatures and speeds directly, during program operation;

- change to running a different iron program, at any time during program operation of the dryer ironer.

Function keys.The functions of these keys change, depen-ding on which menu or part of a menu you are using.

Display screen

Emergency stop

Emergency stop

Lever for manual mode

ELECTROLUX ITSCPU Software Version 1.00

START MACHINEOPTIONS MENU

Use up and down key then press

0508 32

D0543 D0544


01102046

Notice Date Page2. General

Emergency stop

The emergency stop must be unblocked, if not the machine will not work (to unblock, turn the red button to the right).

If the machine for some reason has to be stopped, abnormal or dangerous running, press emergency stop button.

Release the emergency stop, by turning it clockwise only after checking what motivated this stop.

0814 42

1

2

D2225


01102046

Notice Date Page

Control handle

The control handle will operate differently depending on the parameters selected on the display screen settings.

• In automatic mode, only function (1) is available. Pull the control handle forwards to release the sheet from the clamps and cancel automatic feeding (the sheet will fall into the reception tray).

• If you modify the parameters of the «Basic settings» menu, the control handle will switch to a semi-automatic or manual mode.

Start auto feeding = 0Push the handle to position (2) to start feeding.Start auto feeding = 1Feeding will occur automatically after introducing the piece of linen to be dried into the clamps.

Auto feeding return = 0Pull the handle to position (1) to bring the feeding clamps back to their initial position.Auto feeding return = 1Feeding return is automatic once the piece of linen has been placed on the belts

2. General

0814 52

0 0 0 0 0

D2223

1

2

3

4


01102046

Notice Date Page2. General

Stacker control panel

1. Emergency stop pushbutton

2. Linen stack removal indicator

3. Linen removal pushbutton or re-initialisation of stacker defect

4. Sheet counter with reset function

Note: the ironer - dryer will not operate if the stacker is not connected to the power supply.

When a stack has been created (approx. height: 210 mm) on the stacker deck, this stack will be removed to the evacuation table.

The indicator (2) on the stacker control panel will flash for a few seconds to indicate that a stack has been completed.

Note: the evacuation table can contain one completed stack and another stack in progress on the stacker deck.

Remove the stacks as they reach the evacuation ramp.

A pushbutton (3) can be used to evacuate the stack of linen manually.

A sheet counter (4) with reset function can be used to count the items ironed during a given period.

0508 62 INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Note about the A.C. power• According to the EN 60204-1:1997 standard, the machine is provided for AC supplies

corresponding to the extracted caracteristics below :

4.3.2 AC supplies

Voltage : Steady state voltage : 0,9…1,1 of nominal voltage.

Frequency : 0,99…1,01 of nominal frequency continuously. 0,98…1,02 short time.

Harmonics : Harmonic distorsion not to exceed 10% of the total r.m.s. voltage between live conductors for the sum of the second through to the fifth harmonic. An additional 2% of the total r.m.s. voltage between live conductors for the sum of the sixth through to the 30th harmonic is permissible.

Voltage unbalance : Neither the voltage of the negative sequence component nor the voltage of the zero sequence component in three-phase supplies shall exceed 2% of the positive sequence component.

Voltage interruption : Supply interrupted or at zero voltage for not more than 3ms at any random time in the supply cycle. There shall be more than 1s between successive interruptions.

Voltage dips : Voltage dips shall not exceed 20% of the peak voltage of the supply for more than one cycle. There shall be more than 1s between successive dips.

2. General

0910 13

74032535


01102046

Notice Date Page

Precautions for use• The machine should not be used by children.

• This ironer must be used exclusively for textiles appropriate for machine ironing, which have been previously and exclusively washed in water.

• This machine is for professional use and must be used exclusively by qualified person-nel.

• Blankets should not be ironed.

• Be careful with synthetic linen and also with printed linen. They can melt and stick on the cylinder.

• Do not iron articles that contain plastic, foam, sponge rubber or similarly textured rubber-like materials.

• Do not iron linens coated with solvent, paint, wax, grease or any easily inflammable pro-ducts.

• In case of a gas heated machine, do not assemble the machine on premises containing a dry cleaning machines or other similar machines.

3. Precautions for use

CAUTIONDo not push small pieces of laundry in front of the DIAMMS turners to avoid jamming.

1712 23

D0411


01102046

Notice Date Page 3. Precautions for use

PRACTICES TO AVOID : - Sheets folded double. - Draw-sheets or any other double-layer sheet or sheet pulled into the ma-chine side by side. - Fitted-sheet : May cause problem to smooth out; Measurements altered. - Comforter cases with flap - Linen ≤ 80 gr /m² : gravitational pull difficult at lengthwise folding - Linen ≥ 200 gr/m². - Linen < 0,90m x 1,10m. PRACTICES NOT ADVISABLE : - Worn polycotton sheets (cotton worn away) : get out of shape when smoothed out, uneven finish look when folded, high static electricity. - Large cotton or flax-made sheets > 200 gr/m² (layers > 80 mm after the 3rd cross fold). - Linen other than flatwork : (butcher's apron : watch that the cords do not slide between the feeding belts). - Sheets of 1m80 x 2m80 processed on type 25 - 2m50 - (gas heating : problem of heating regulation with gas; gas burners cannot be modulated ). CAUTIONS : - Prepare the large sheets before feeding : ironing and folding defects, risks of jamming at cross folding. - Avoid the torn, worn or holed sheets : that may hook and alter the measurements hampering proper lengthwise folding (back clearing). - Comply with the mini-maxi sizes. - Avoid when running, too low or bad adjusted temperatures as consequence of : - A too high ironing speed with high moisture content in sheets : bad sliding on metallic parts. - A partial use of the ironing length of the cylinder creating overheating : (be careful especially, to the risk for the polycotton sheets to loose their shape, generally stabilized at 200 °C).

0708 14

D1097


01102046

Notice Date Page

Easy

sta

rtEasy start

Additional instructions to optimise a dryer-ironerWhen ironing small sheets or small washing, pass abreast the washing of the heating cylinder to provide correct regulation of the cylinder temperature.

As a general rule, the whole of the cylinder should be used (1). Either iron the linen from the front (2) or iron alternately (3), which makes maximum use of the heat units available over the surface of the cylinder. It also overcomes difficulties arising from random control values caused by partial use of the cylinder.

Cylinder

Linen

4. Machine operation

0708 24

D1663

STOP

1

2

…

1.........

2.........

3.........

4.........

180

5,5 m

°C

min 250

1


01102046

Notice Date Page 4. Machine operation

Machine starting

The "Move back" key

Each press of the "Move back" key moves you back one menu, in reverse order.By pressing this key repeatedly you can return to this menu at any time :

The "Move back" functionIf you find you are in the wrong place, or if you want to undo earlier key presses :

Press the "Move back" key one or more times.

Easy

sta

rtEasy start

Setting out






After putting the main switch on 1, the menu opposite is displayed on the machine.

If "OPTIONS MENU" is highlighted,

Press this key.

When "START MACHINE" is highlighted,

Press this key.

u"DIAMMS MODE" display (next page)

0708 34

D1663

STOP

1

2

…

1.........

2.........

3.........

4.........

180

5,5 m

°C

min 250

1

D1639

1

D1663

STOP

1

2

…

1.........

2.........

3.........

4.........

180

5,5 m

°C

min 250

1


01102046

Notice Date Page4. Machine operation

Easy

sta

rtEasy start

"DIAMMS MODE" display

To go in MANUAL mode, push on :

"Diamms/Manual"

To go in ejection mode, push on :

"Ejection"

To go in select program mode, push on :

"Select program"

During the operating cycle, the display shows the opposite informations and commands in DIAMMS mode.

To go in without folding mode, push on :

"Folding"

To go in feeding mode, push on :

"Feeding"

To stop the operating cycle, push on :

"Stop"

Warming up

From the machine starting, the order of warming up is given. The cylinder temprature increases.

The machine is adjusted in automatic mode by default.

Temperature

Shows the cylinder temprature.

Speed

Shows the cylinder speed.

Moisture

Shows the moisture.

Counter of items

Shows the number of items of linen passed in the machine.

Folds table choice

Shows the selected folds table.

u"MANUAL MODE" display (next page)

1110 44

2

3

1

D1092


01102046


Remark:

Incompatibility of the DIAMMS with the ironing of the linen with double thickness

The use of automatic control mode using the DIAMMS is not recommended for ironing clothes with a double thickness (eg duvet covers), the measurement of residual moisture being carried on thickness. It is advisable in this case return to MANUAL mode and adjust the speed of ironing to get a good drying performance.

Easy

sta

rt

Easy

sta

rt

Using the handleThe dryer ironer is fitted with a handle.

This is very useful to take out the washing if there is a power failure while you are ironing; or you can use it to feed a piece of wet washing to protect the ironing bands when the ironing temperature is too high.

Lift the safety plate (1) then push (2) and turn the handle in the clockwise direction (3) to rotate the cylinder and take out the washing.

Handle

D1662

STOP

+

-

+

-1

2

…

1.........

2.........

3.........

4.........

180

5,5 m

°C

min 250

1

D1639

1

0109 54INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Easy

sta

rt

Easy start

MANUAL mode selection

To go in DIAMMS mode, push on :

"Diamms/Manual"

To go in ejection mode, push on :

"Ejection"


"Select program"

During the operating cycle, the display shows the opposite informations and commands in MANUAL mode.

To go in without folding mode, push on :

"Folding"

To go in feeding mode, push on :

"Feeding"

To stop the operating cycle, push on : "Stop"

If you push on

you go in manual mode.

In this mode, you select in the following menus, the temperature and the ironing speed you want apply to use the machine.

Set temprature

Ironing speed

"MANUAL MODE" display

u"DIAMMS MODE" display (previous page)

u"STOPPING" menu (next page)

Now the display waits for you to select the set temperature for the ironing.

The ironing temperature can be adjusted degrees by degrees Celsius by push.

N. B. : if you want a temperature below 100°C, the display shows a sign (0) to indicate that the heating is cut off and allows the machine to work without heating.

Now the display waits for you to select the ironing speed.

The ironing speed is adjusted between a minimal value and a maximal value in the Setting mode. The adjustment can be modified 1/10 by 1/10 of meter by push.

Note that the minimal and maximal ironing speeds are in accordance with the adjustment parameters of the converter.


1108 64 INSTRUCTION

HANDBOOK

01102046


Easy

sta

rtEasy startFOLDS TABLE CHOICE

0. Factory folds table1. Customized folds table (recommended)1. Reversed customized folds table2. Specific folds table2. Reversed specific folds table

Folds table choice

This screen allows you to select the folds table :

n° 0 Factory folds table,

n° 1 Customized folds table,

n° 1 Reversed cutomized folds table,

n° 2 Specific folds table,

n° 2 Reversed specific folds table.

Press on and keys to select the folds table you want to use, then press the «Valid» key to validate your choice or press the «Move back» key to cancel.

In Diamms or Manual mode, when we touch the screen in the center area, the «FOLDS TABLE CHOICE» screen appears as opposite.

To choose the folds table.

"FOLDS TABLE CHOICE" display

To escape, push on :

"Move back" key

u"DIAMMS MODE / MANUAL MODE" display (previous page)

To valid, push on :

"Valid" key

u"DIAMMS MODE / MANUAL MODE" display (previous page)

0708 74INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Easy

sta

rtEasy start

"STOPPING" menu


"Move back" key

STOPPING ?To confirm, push on To access tools, push on

u"DIAMMS / MANUAL MODE" display (previous page)

To enter, push on :

"Valid" key

u"ELECTROLUX ITS" or "COOLING" menu (next page)

Otherwise, push on :

"Tools"

u"OPTIONS MENU"

Stopping

This function allows you to stop the machine or to access the «Options menu» to carry out a modification.

Before stopping, the machine executes a cool down stage that allows to avoid damage to the ironing bands.


0708 84 INSTRUCTION

HANDBOOK

01102046


Cooling


"Move back" key

u"POWER IS BACK" display (next page)


"Tools"

u"OPTIONS MENU"

Stop confirmed, cooling

"COOLING" menu

"OPTIONS MENU"


"Move back" key

u"COOLING" menu

OPTIONS MENU

This display allows you to follow the cool down stage.

You can at every time stop this cool down stage to start again, or access the «Options menu» to carry out a modification.

BASIC SETTINGSPROGRAMMING

ADVANCED SETTINGSSTATISTICS

DATE & TIME SETTINGPASSWORD CHANGE

MACHINE STATUSUSER LANGUAGE

Easy

sta

rtEasy start

1209 94INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Easy

sta

rtEasy start

In case of escaping of the cooling stage, the screen opposite is displayed to take back the use of the machine.

u"DIAMMS / MANUAL MODE" display

u"COOLING" menu (previous page)

To escape the program,

press "Move back" key

POWER IS BACK

Do you want to continue the cycle ?

To continue the cycle,

press the "Valid" key

"POWER IS BACK" display

Power is back


1209 104

D1362


01102046


D1362

01. EMERG. STOP ACTIVEDesactive emergency stop

and restart the machine

u"ELECTROLUX ITS" menu

After the emergency stop releasing, push on :

"Valid" key

"EMERGENCY STOP" display

If the machine for some reason has to be stopped, abnormal or dangerous running, press emergency stop button.

Release the emergency stop, by turning it clockwise only after checking what motivated this stop.

Emergency stopAfter a pushing on the emergency stop, the opposite display appears.

Easy

sta

rtEasy start

D1663

STOP

1

2

…

1.........

2.........

3.........

4.........

180

5,5 m

°C

min 250

1

1209 114INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Easy

sta

rtEasy start

Run a program

The "Select program" key


"Select program"

"SELECT PROGRAM" menu

SELECT PROGRAM

00 Universal01 Folding adjustment mode02 Cloth 300x240 poly/cotton05 Draw-sheet 190x24010 Fitted-sheet 300x240 cotton18 Cloth 190x240 poly/cotton20 Draw-sheet 250x240

Allows to choose the program.

Previous and next page.

To enter, push on :

"Valid" key

u"DIAMMS / MANUAL MODE" menu (next page)

After pushing on select program, the opposite display appears.

The number and the name of program are indicated above the command buttons.

Program

Customer programs


0708 124 INSTRUCTION

HANDBOOK

01102046


18 Cloth 190x240 poly/cotton Elis

Easy

sta

rtEasy start

"ENERGY SAVING MODE" display

MACHINE IN ENERGY SAVING MODE

To restart at previous mode :

The «Energy saving» mode shuts off the machine after a predefined time in the settings. Push on the screen to restart the machine.

uPrevious page (according to operation)

NOTE : in «Energy saving» mode, the machine adjusts temperature to the setpoint temperature minus 40°C.

The functions are the same as for the operating cycle in Universal Diamms mode.

Start the selected dryprogram (in this case 18)

Energy saving

Program mode

1108 15

D1376D1371

D1369

D1312

D1374D1376


01102046

Notice Date Page

BASIC SETTINGS

Since the "OPTIONS MENU"

OPTIONS MENUBASIC SETTINGSPROGRAMMING




Select the "BASIC SETTINGS" menu

by pressing this keys.

Then valid.

Password : #

Compose the four number code with the numeric keys.

You can correct a bad capture

by pressing this key.

Then valid.

u"BASIC SETTINGS" menu (next page)

"NUMERIC KEYBOARD" menu

A password (a four-digit number), protects the access to the "Basic settings" functions.

Numeric keyboard

5. Advanced use

0210 25

00

01


01102046

Notice Date Page 5. Advanced use

BASIC SETTINGS

Feeding auto. start : 0 Feeding auto. return : 0Folds table choice : 0Folding table settingFeeding sucking system : 0Standby timer (min) : 0Sleeping timer (min) : 0Lenght counter display : 0

Select the wished function


Decrease or increase the value


Then valid.

Feeding auto. start1= the feeding start is automatic after introduction of the linen item in the two pincers; 0= the central lever must be actionned.

Feeding auto. return1= the feeding return is automatic after putting the linen item on the bands; 0= the central lever must be actionned.

Folds table choice0 = the machine will use the «factory» folding table;1 = the machine will use the «customized» folding table;2 = the machine will use the «specific» folding table.

Folding table settingAllows to access to the «customer folding table» display.

u"FOLDING TABLE" display (next page)

Feeding sucking system1=, the feeding suction is on; 0= is off for the little items of linen.This allows to decrease the sound level of the machine and so the electrical consumption.

Standby timer (min)Adjusts the time before standby (minutes).

Sleeping timer (min)Adjusts the time before automatic stop (minutes).

Length measure display1= shows the item length instead of the counter of items (cm).

3rd Cross Fold activat.0 = cross fold 3 disabled.1 = cross fold 3 enabled.

Parameters savingSaves board parameters in the event that one of them is replaced.

"BASIC SETTINGS" menuBasic settings

1209 35

00

01


01102046

Notice Date Page

"SET CUSTOMIZED FOLDS TABLE" menu

SET CUSTOMIZED FOLDS TABLE0. Factory folds table

0 = no adjustment possible.1 = use customer folds table.2 = use specific folds table.

Lenght = 182Length of the last item inserted into the machine (= 0, when the machine is stopped).

180 ≤ Lenght < 185Selected length range. Automatically selected when the machine is in use.

Fold 1, Folds 2&3 ...Value of each fold for the selected length of fold (factry settings in brackets).

CAUTION :To guarantee a correct result, ensure that the last fold ≥ 23 and the penultimate fold has the largest value.

NOTE :This screen can also be accessed from the program list (program No. 1) when the machine is in use.

0. Factory folds tableLength = 182

180 ≤ Length < 185Fold 1 (0): 0Fold 2&3 (0): 0Fold 4&5 (0): 0Fold 6&7 (0): 0= > Last fold = 0 & offset = 0





Then valid.

Set customized folds table

5. Advanced use

1108 45

D1312

D1370 D1370

D1370 D1370

D1369


01102046

Notice Date Page

ADVANCED SETTINGS






Select the "ADVANCED SETTINGS" menu


Then valid.

Password : #




Then valid.

u"ADVANCED SETTINGS" menu (next page)


A password (a four-digit number), protects the access to the "Advanced settings" functions.

Numeric keyboard

5. Advanced use

1209 55INSTRUCTION

HANDBOOK

01102046

Notice Date Page

ADVANCED SETTINGS

Machine configuration Machine timers settingParameters recovering

Maintenance alert (h) : 134



Then valid.

"ADVANCED SETTINGS" menuAdvanced settings

Machine configurationAccess reserved to the technician.

Machine timers settingAccess reserved to the technician.

Perameters recoveringAccess reserved to the technician.

Maintenance alert (h)Access reserved to the technician.

5. Advanced use

1108 65

D1312

D1371 D1376

D1376 D1374

D1369


01102046

Notice Date Page

STATISTICS


Select the "STATISTICS" menu


Then valid.

Password : #




Then valid.

u"STATISTICS" menu (next page)






A password (a four-digit number), protects the access to the "Statistics" functions.

Numeric keyboard

5. Advanced use

1209 75INSTRUCTION

HANDBOOK

01102046

Notice Date Page

"Day statistics" menu


"Move back" key

u"STATISTICS" menu

u"STATISTICS" menu

Otherwise,

push on "Valid" key

To move back, press the :

"Move back" key

u"OPTIONS MENU"

The Statistics function gives you access to the following information :Day statistics

List the statistics recorded in a day.Monthly statistics

Access with Customer passord.Absolute statistics

Access reserved to the technician.Temperature display

Access reserved to the technician.Errors statistics

Access reserved to the technician.

Then valid.

Select "Day statistics"


Reset the counters.

STATISTICS

day statistics monthly statisticsabsolute statistics

temperatures statisticserrors statistics

Total Hours Since New : 480Used Hours : 420

Processed items : 1028Machine defaults : 1Rejected items : 187

Day statistics Total Hours Since New (min)

Shows the total operating time for the machine since new.

Used Hours (min)Shows the total using time.

Processed itemsCounts the items treated in a day.

Machine defaultsCounts the machine defaults recorded in a day.

Rejected itemsCounts the items rejected in a day.

"STATISTICS" displayThe «Statistics» function

Day statistics

5. Advanced use

1209 85 INSTRUCTION

HANDBOOK

01102046

Notice Date Page

"DATE & TIME SETTING" menu

DATE & TIME SETTING

DATE:00/00/00

dd/mm/yy

Date format (+/-)

TIME

00:00


"Move back" key

To enter, push on :

"Valid" key

This function allows you to adjust the date and the hour of the machine.

This is notably useful to quote the statistics and the maintenance.

To move the cursors,

To set the value indicated by the cursor,

Select the "DATE & TIME SETTING" menu


Then valid.

DATE AND TIME SETTING






Date & time setting

5. Advanced use

1108 95

English FrançaisDeutshEspañolItaliano

Nederlands

English FrançaisDeutshEspañol

English FrançaisDeutshEspañol


01102046

Notice Date Page

Select the "USER LANGUAGE" menu


Then valid.

LANGUAGE SETTING






"USER LANGUAGE" menu

If another language is highlighted,

press this keys.

When the wished language is highlighted,

press this key.

USER LANGUAGE

5. Advanced use

0608 105

D1312

D1371 D1376

D1376 D1374

D1369


01102046

Notice Date Page


A password (a four-digit number), protects the access to the "Programming" functions.

PROGRAMMING


Select the "PROGRAMMING" menu


Then valid.




Then valid.

u"PROGRAMMING" menu (next page)

Password : #





Numeric keyboard

5. Advanced use

1209 115INSTRUCTION

HANDBOOK

01102046

Notice Date Page

CREATE PROGRAM

Since the "PROGRAMMING" menu

Select the "CREATE PROGRAM" menu


Then valid.

u"PROGRAM EDITION" menu (next page)

PROGRAMMING

CREATE PROGRAMMODIFY PROGRAMDELETE PROGRAM

An introduction to programmingYou can create a completely new program from a basic program and by programming a number of adjustments to form a new program.Programs can be created directly on the machine’s control console.

5. Advanced use

1209 125

00

01


01102046

Notice Date Page

"PROGRAM EDITION" menu

The parameters of each program are accessible and can be modified :

DIAMMS regulationAllows to select between DIAMMS or MANUAL mode.

TemperatureAdjusts the temperature.

Speed (m/mn)Adjusts the speed.

Automatic feedingEnables automatic feeding, otherwise feeding is done manually.

Automatic returnAuthorizes the automatic return, dans in the contrary case, the return is driven by the central lever.

Non-folded length (cm)Indicates the non-folded length(± 6cm).

Non-folded width (cm)Indicates the non-folded width (± 6cm).

FoldingAllows the folding.

Length L (cm)Adjusts the stack length.

Width W (cm)Adjusts the stack width.

Cloths number by stackAdjusts the cloths number by stack.


"Move back" key

PROGRAM EDITION##DIAMMS regulation : 0Temperature : 178°CSpeed (m/mn) : 4,5Automatic feeding :1Automatic return : 0Non-folded length (cm) : 190Non-folded width (cm) : 240Folding : 1Length L (cm) : 38Width W (cm) : 32Cloths nb by stack : 05

Select the wished parameter




Then valid.

u"PROGRAM NUMBER" menu (next page)

Program edition

5. Advanced use

0608 135

D1369

D1369

D1312


01102046

Notice Date Page

Program Name :A numeric keyboard allows to give a program name (formed by letters).Each of the numeric keys gives access to several characters as follows :1 : abc 2 : def 3 : ghi4 : jkl 5 : mno 6 : pqr7 : stu 8 : vwx 9 : yz0 :

The first time you press a given key, the first character available through that key will appear on the display. One press on 1 produces A. One press on 2 produces D.Simply press the relevant key the required number of times until the character you want appears on the display. For example, to insert the letter C, press key 1 three times. To insert F, press 2 three times.When the character you want is on the display, wait a minute the cursor sets after.

Compose your program name with the numeric keys, by pressing 1, 2 or 3 times on each key.



Then valid.

u"PROGRAMMING" menu

Program Name : F_

Program Name : FF_

"PROGRAM NUMBER" menu

Compose a number with the numeric keys.



Then valid.

A number allows to select the dry programs by numerical order.Enter the program number :

"NUMERIC KEYBOARD" menuNumeric keyboard

u"NUMERIC KEYBOARD" menu

Numeric keyboard

Program number

5. Advanced use


HANDBOOK

01102046

Notice Date Page

MODIFY PROGRAM


Select the "MODIFY PROGRAM" menu


Then valid.

You can create a new program starting from a basic program and by programming a number of adjustments, to form a new program.

Programs can be programmed directly on the machine, via the PCU control panel, which is the method described in this manual.

To enter, push on :

"Valid" key



u"PROGRAM EDITION" menu (next page)

PROGRAMMING

CREATE PROGRAM MODIFY PROGRAMDELETE PROGRAM

SELECT PROGRAM

01 Universal02 Cloth 300x240 poly/cotton05 Draw-sheet 190x24010 Fitted-sheet 300x240 cotton18 Cloth 190x240 poly/cotton20 Draw-sheet 250x24099 Folding adjustment mode


An introduction to programming

5. Advanced use

1209 155

D1312


01102046

Notice Date Page

"PROGRAM EDITION" menu

PROGRAM EDITION

Then valid.

u"PROGRAM NUMBER" menu

##DIAMMS regulation : 0Temperature : 178°CSpeed (m/mn) : 4,5Automatic feeding :1Automatic return : 0Non-folded length (cm) : 190Non-folded width (cm) : 240Folding : 1Length L (cm) : 38Width W (cm) : 32Cloths nb by stack : 05

See page 12 / Chapter 5

Then valid.

See page 13 / Chapter 5Enter the program number :

"PROGRAM NUMBER" menu

u"NUMERIC KEYBOARD" menu (next page)

Program number

Program edition

5. Advanced use


HANDBOOK

01102046

Notice Date Page

Program Name :See page 13 / Chapter 5

Then valid.

u"KILL THE EXISTING PROGRAM" display


u"PROGRAMMING" menu

u"NUMERIC KEYBOARD" menu


"Move back" key

DO YOU WANT TO OVERWRITE

EXISTING WASHPROGRAM ?

When the validation executed, the previous program is definitely lost and replaced by the new one.


"Valid" key

"KILL THE EXISTING PROGRAM" display

Numeric keyboard

Kill an existing program

5. Advanced use

0608 175INSTRUCTION

HANDBOOK

01102046

Notice Date Page


5. Advanced use


HANDBOOK

01102046

Notice Date Page

Select the "DELETE PROGRAM" menu


Then valid.

To enter, push on :

"Valid" key



u"DELETE THE PROGRAM" display (next page)

DELETE PROGRAM


PROGRAMMING

CREATE PROGRAM MODIFY PROGRAMDELETE PROGRAM


SELECT PROGRAM


5. Advanced use

0608 195INSTRUCTION

HANDBOOK

01102046

Notice Date Page

When the validation is executed, the program is definitely deleted.

u"PROGRAMMING" menu

u"PROGRAMMING" menu

DO YOU WANT TO DELETE


"Move back" key


"Valid" key

THE PROGRAM ?

"DELETE THE PROGRAM" displayDelete a washprogram

5. Advanced use

D1663

STOP

1

2

…

1.........

2.........

3.........

4.........

180

5,5 m

°C

min 250

1


HANDBOOK

01102046

Notice Date Page





From the start menu,Select «START MACHINE»,

Select«START MACHINE

u"DIAMMS MODE" screen


Then valid.

The «DIAMMS MODE» screen appears as shown opposite.

Push on

«Select program»

u"SELECT PROGRAM" screen

5. Advanced use

00

01

1209 215INSTRUCTION

HANDBOOK

01102046

Notice Date Page

SELECT PROGRAM


The «SELECT PROGRAM» screen appears as shown opposite.

Select program No. 01 «Folding table adjustment mode»

u"SET CUSTOMIZED FOLDS TABLE" display

Then valid.

SET CUSTOMIZED FOLDS TABLE

Select a function

by pressing these keys.

Raise or lower the value

by pressing these keys.

Then valid.

0. Factory folds tableLength = 182

180 ≤ Length < 185Fold 1 (0): 0Fold 2&3 (0): 0Fold 4&5 (0): 0Fold 6&7 (0): 0= > Last fold = 0 & offset = 0

The «SET CUSTOMIZED FOLDS TABLE» screen appears as shown opposite.

CAUTION :To guarantee a correct result, ensure that the first fold ≥ 23, the last fold ≥ 23 and the penultimate fold has the largest value.

5. Advanced use

1209 16 INSTRUCTION

HANDBOOK

01102046

Notice Date Page

POWERIS BACK

EMERGENCYSTOP

ECRANELECTROLUX ITS

OPTIONSMENU PROGRAMMING

STOPPING

BASICSETTINGS

ADVANCEDSETTINGS

STATISTICS

PASSWORD CHANGE

USERLANGUAGE

SELECTPROGRAM

DIAMMSMODE

MANUALMODE

MANUALX PROGRAM

DIAMMSX PROGRAM

Diagram of Electrolux ITS menus

DATE & TIME SETTING

MACHINE STATUSCaption :

normalfunctioning

adjustment function

wrong functioning password

move back way

normal way

Caption :

normal way with

automatical advance

emergency stop or «power is back»

way

Caption :

6. Additionalinformation of using

1209 26

RECUPEARTION PARAMETRES


01102046

Notice Date Page6. Additional

information of using

MACHINE CONFIGURATION

MONTHLY STATISTICS

DAILY STATISTICS

DELETE PRO.SELECT ?

DELETE PRO.ERASE ?

MODIFY PRO.SELECT ?

MODIFY PRO....EDITION

MODIFY PRO.NUMBER ?

MODIFY PRO.NAME ?

CREATE PRO....EDITION

CREATE PRO.NUMBER ?

CREATE PRO.NAME ?

FOLDING TABLE

ABSOLUTE STATISTICS

MODIFY PRO.KILL ?

TEMPERATURE DISPLAY

MACHINE DELAYS SETTING

MAINTENANCE ALERT

PARAMETERS RECOVERING

ERRORS STATISTICS

0508 17 INSTRUCTION

HANDBOOK

01102046

Notice Date Page


7. Safety

0508 27INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Safety devices

AccessibilityAll of the casings can be dismantled by means of a specially designed tool.

Emergency stopAn "emergency stop" button is provided on the left side and on the stacker.

Restarting the machineAfter any stoppage of the machine, either due to power failure, emergency stop, action on the feed safety device, the machine can only be restarted after having pressed "Valid" key.

Feed safety deviceThe space between the feed safety flap and the drive bands is too small for you to enter your fingers. The machine stops automatically as soon as the flap is pushed in.

Power supply failureIf there is a mains power supply failure, use the handle to remove any washing engaged in the machine. If the temperature is too high, use the handle to feed some wet washing and protect the ironing bands.

Protection of motorsThe motors have overload protection : • by thermomagnetic circuit breakers and • by the electrical selector (for movement).

Heating safety deviceThe control panel applies an initial safety level at the time the machine starts up.If the temperature is not reached after a given time, the heating command is desactivated.The operation of the heating function is linked to the rotation of the cylinder. If the cylinder should stop rotating for any reason, the machine stops heating.A safety thermostat, which is independent of all electronic systems, limits the heating tempera-ture of the ironing cylinder in all circumstances, exept in the case of a steam heating machine.There is a thermical fuse for the overheating safety, in the centre of the machines equiped with a Dubixium cylinder. If it breaks, the heating stops. Contact your dealer to check the origin of the failure by a qualified technician.

Gas heatingThe gas burner is ignited and the flame is controlled by an electronic box that provides integral safety, for example if the flue draft is poor or if the gas supply is cut off.A message on the tactile screen shows that the system has been put in a safe condition.A pressure switch connected to the combustion products outlet turns off the machine’s heating function in case of extraction problems.

7. Safety

1209 18 INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Operating incidentsIn order to limit the risk of failure in the electronic controls of the programming unit of the ma-chine, the machine should be earthed. Should interferences happen, the first thing to be chec-ked is the earthing of the machine.

The programming unit permanently checks the machine, regarding both safety and working aspects. To make the fault finding easier, the display window indicates in clear text the origin of the failure, or the reason why the particular function cannot be used. The table below gives for each problem detected the message of the machine and the solutions to be brought.

Error/Function Cause Action

Displayed advertisement :

01. EMERGENCY STOP ACTIVERelease emergency stop

and start the machine


02. LACK OF COMPRESSED AIRCheck compressed air pressure (5 bars)

or contact your technician


03. GAS PRESSURE FAILURECheck gas supply valve


Reason : one emergency stop button has been pressed.

- Abnormal or dangerous running of the machine.

If the problem is solved : Push on «Valid» key to restart the machine.

- Remedy the problem that caused the emergency stop and release the emergency stop button in a clockwise direction.

Reason : A slight drop in air pressure has been detected (detected by the manome-ter).

- Manual water valves (taps) are close.

- No air in main supply.

- Air leak in the circuit.


- Open taps.

- Check air in main supply (5 bars on the B1 pressure control-ler).

- Find the leak and repair it.

Reason : A slight drop in gas pressure has been detected.

- Manual gas valves (taps) are close.

- No gas in main supply.


- Open taps.

- Check gas in main supply.

8. Operating incidents

1209 28INSTRUCTION

HANDBOOK

01102046

Notice Date Page8. Operating incidents



05. OVERHEAT DETECTIONCool machine down in manual mode



06. MAIN TRANSMISSION ERRORRead instructions in the manual



07. LENGTH FOLDING ERRORRead instructions in the manual



04. GAS IGNITION ERRORReset ignition process


Reason : The gas burner does not start.

- No gas in connection.

- No gas in burner.

- No flame in burner.


- Check gas in main supply.

- Check the Y1/Y2 gas electro-valves.

- Check the E2/E3 ignition elec-trodes.

Reason : A temperature overheat has been detected.

- One of the temperature measurement is over the limit value (<230°C).


- Decrease the heating tempera-ture by ironing wet sheets.

- Reduce the program’s temperature value.

Reason : A problem has occured with the main transmission.

- No status change of the counting detec-tor.

- No status change of the main transmis-sion when running is asked.


- Check the DP1 counting de-tector.

- Check the cinematic chain of the ironing cylinder (motor opera-tion M1, converter A0, transmis-sion chain).

Reason : A problem has occured with the folding arm.

- No status change of the folding arm position detector.

- No status change of the folding arm position, despite folding request.


- Check the DP3 and DP4 de-tectors.

- Check the cinematic chain of the E1 folding arm (electric clutch operation, transmission chain).

1209 38 INSTRUCTION

HANDBOOK

01102046

Notice Date Page8. Operating

incidents



09. FOLDING TRANSFER ERRORRead instructions in the manual



10. CROSS FOLD 1 JAMEDRemove item according to instructionsin manual or contact your technician


11. CROSS FOLD 2 OR 3 JAMEDRemove item according to instructionsin manual or contact your technician


08. FOLDING MEASURE ERRORRead instructions in the manual


Reason : A problem has occured with the folding measure.

- Sheet not detected at longitudinal fold.


- Check the DP7.

Actually out of service.

Reason : A jamed has occured with cross fold 1.

- The sheet is jammed at the inlet of the cross of the first fold.


- Clear the item by disengaging the cross transmission if necessary (index pin on the pulley).

Reason : A jamed has occured with cross fold 2 or 3.

- The sheet is jamed in the second or third cross fold.


- Disengage the item (see above).

0910 48INSTRUCTION

HANDBOOK

01102046

Notice Date Page8. Operating

incidents


13. STACKER ERRORRead instructions in the manual



14. THERMIC FUSE FAULTRead instructions in the manual



12. JAM AT CROSS FOLD EXITRemove item according to instructionsin manual or contact your technician

Reason : A bad operation of the stacker is detected.

- No status change of the stacker position detection.

- No status change of the stacker posi-tion.


- Check the detector.

- Check the mechanical opera-tion of each table function (mo-tion, detection, opening, closing).

Reason : A temperature overheating is detected.

- A temperature overheating is detected (>240°C).



- When the machine is stopped, change the F2 fuse.


Displayed advertisement (for Australia ironers only) :

Reason : The overheating safety switch is open.

- A temperature overheating is occured (>215°C).

If the problem is solved : Push on the yellow «Reclosing button» then restart the machine.


15. OVERHEAT. SAFETY SWITCHRead instructions in the manual

or contact your technicien

Reason : A jamed has occured with cross fold exit.

- The sheet is jammed at the exit from the cross on the transfer table.

- No sheet detection on the transfer table.


- Clear the item by disengaging the cross transmission if necessary (index pin on the pulley).

- Check the DP28 detector.

0210 58 INSTRUCTION

HANDBOOK

01102046

Notice Date Page 8. Operating incidents


17. HEATING ERRORRead instructions in the manual



20. COM FAILURERead instructions in the manual


Reason : A problem has occured with the heating.

- Status of the heating contactor is not in accordance with the command.


- Stop the machine by means of the main switch, turn the ironing cylinder with the handle to avoid burning the bands.When the cylinder is cold,replace the contactor.

Reason : A problem has occured with the electronic command.

- Communication between electronic boards is not working properly.


- Check the communication wires between boards.



16. EXHAUSTING FAILURERead instructions in the manual


Reason : A problem has occured with the throwing out of the burned gas.

- Overabundance of burned gas in the machine.


- Check the evacuation of the burning gas as well as the fan motor.

Displayed advertisement (other machines) :

Reason : The overheating safety switch is open.

- A temperature overheating is occured (>215°C).



15. OVERHEAT. SAFETY SWITCHRead instructions in the manual

or contact your technicien

0408 68INSTRUCTION

HANDBOOK

01102046

Notice Date Page


8. Operating incidents

1711 19

1

15

22

4

523

7

26

17

19

8

8

20

27

28

30

31

32

10

93

11

19

3

4

4

44

11

11

2

29

24 6 21

22

422

25

23

18

16

1

14

8

4

12

15

3

6

INSTRUCTIONHANDBOOK

01102046

Notice Date Page

CAUTIONFor an optimal service of your machine, execute this instructions at regular intervals and according to the frequency of use.

Maintenance

9. Preventive maintenance

2514 29INSTRUCTION

HANDBOOK

01102046

Notice Date Page9. Preventive maintenance

Daily (8 h) (at the beginning of each working day)1 Check that the emergency stop button works correctly.2 Check that the machine stops when you press the mobile safety protector.

Weekly (40 h)3 Clean the drive system of the dewrinkling strips.4 Clean motor ventilation grills.5 Clean the separators.6 Clean the detection cells and the refl ectors.7 Check and clean the fl uff fi lter (on gas heating only). Clean the box of the fi lter with

suction device.

Monthly (170 h)8 Remove dust from outside the machine.9 Ensure that the thermostatic regulation and overheat safety shoes are always clean

and in contact with the cylinder.10 Check the condition of the smoothing belts, and replace them if necessary.11 Lubricate the steam heater bearings (see lubrication chart in next pages).12 Turn the blue O ring seals of the feeding pincers through 1/8 of a turn to relieve their bearing surface when the pincers close.

Every six months (1000 h)13 Check for any possible oil seepage, particularly at the fi ller plug (only on Dubixium

cylinders).14 Grease chains (see lubrifi cation table on the next pages).15 Clean and inspect the cylinder support rollers, along with the stop roller wear indicator

(except on the steam machine). If there is any premature wear, see technical support, ref. 04102018.

16 Check operation of the handle.17 Inspect tightness of electrical connections on the power supply terminal block and

electrical earthing connections.18 Clean exhaust system.19 Inspect heating elements, cables and electrical connections (on electrical heating

only).20 Clean gas fi lter inside the gas valve (on gas heating only).21 Check the condition of ironing bands and their staples.22 Check the feed bands and their drive and ejection bands (on models with the folding

function only).23 Clean inside the machine.

1711 39

1

15

22

4

523

7

26

17

19

8

8

20

27

28

30

31

32

10

93

11

19

3

4

4

44

11

11

2

29

24 6 21

22

422

25

23

18

16

1

14

8

4

12

15

3

6

INSTRUCTIONHANDBOOK

01102046

Notice Date Page 9. Preventive maintenance

CAUTION

To ensure that your machine gives the very best service, please take care that maintenance is carried strict accordance with the instructions above mentioned.

Maintenance

0212 49INSTRUCTION

HANDBOOK

01102046


Every year (2000 h)24 Check if the cylinder is dirty and clean it if necessary.25 Clean external pipes done by customer.26 Check that the burner works correctly (gas machines only).27 Clean the inner gas burner with suction device.28 Check the sight of the ceramic plates joints and change them if necessary.29 The bearings must be grease once a year, you may grease them using a grease

which same characteristics as that originally used (grease CELTIA G2).

Every three year (6000 h)30 Clean the ceramic plates with suction device.31 Change the high temperature joints made of mineral wool.32 Check the tightness of the venturis.

Motors• The fan motor is life lubricated.• The movement reduction gear is life lubricated.

Bearings• The bearings must be grease once a year, you may grease them using a grease

which same characteristics as that originally used (grease CELTIA G2).• Grease periodically the two bearings on the steam cylinder (please see «Preventive

maintenance») using a grease which is resistant to high temperatures.

Cylinder• The cylinder must be maintained very carefully so that ironing is easy and good quality.• Detergent or scale deposits must be removed as soon as they reduce ironing quality (jamming, creases on the washing, etc.).

Note:

The drier-ironing machine textile components must be considered as wearing parts. The lifetime of these parts (ironing strips, feeding strips, clamping belts, transfer belts, etc.) is highly dependent on the usage conditions and maintenance frequencies. Consequently, their replacement may not be claimed under any guarantee.

92811 5

D1816

O

D2004

F

D2011

KM9


01102046


Air compressorSome machines are supplied with an integrated air compressor.

At first start, it is necessary to turn off the compressor manometer tap, wait until the compressor reaches the pressure of 7 bars, then re-open the valve.

Every 6 months

Check the oil level regularly and top up if necessary (O). Carry out this operation with the machine cold.

Start up the ironing machine in folding mode (the reception tub must be in vertical position).

Remove the left hand side casing to access the electricity cabinet.

Activate relay KM9 to move the folding arm forward.

Check that the oil level is now visible on the level indicator. Top up if necessary.

Put the arm back in rear position by activating relay KM9 again.

Put the side casing back.

Every 6 months

Check the cleanliness of the intake filter, clean if necessary (F).

TD2005

92811 6INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Every 6 months

Purge regularly the water separator tap (T).

9. Preventive maintenance

2714 79

D2268

INSTRUCTIONHANDBOOK

01102046


Old band

New band

Pull on the old band

Cylinder direction of

rotation

Staples

Satellite

Tensioning satellite

Replacing ironing bands• Remove the rear casing to obtain easy access to the ironing bands.

• Remove staples from the two ends of the bands to be replaced and staple the end of the old band with the end of the new band.

• Rotate the cylinder using the handle.

• Unstaple the ends of the old and the new band, and staple the two ends of the new band together.

• Do the same for the other bands.

• Replace the rear casing.

CAUTIONThe tension of the ironing bands was adjusted in the factory with the machine hot.Never retension the bands.Their tension must be as low as possible (just enough to drive them) since excessive tension will cause fast wear of these bands.Remember these comments if you need to make an adjustment or a replacement.

2811 89

-20°C + 140°C -40°C + 200°C -20°C + 150°C -20°C + 135°C -30°C + 700°C 0°C + 100°C 0°C + 120°C +10°C + 65°C

96 011 011 96 011 019 96 011 014 96 011 000 96 011 004 96 010 001 96 010 004 96 010 030

CELTIA G2 NTN SH44 M ALTEMP q NB 50 MI-SETRAL 43N GRACO AF 309 REDUCTELF SP150

REDUCTELF SP200

LUBRAK ATL SAE 5W

BP

CASTROL

ELF

ESSO

FINA

GBSA

GRAFOIL

KLUBER

MOBIL

KERNITE

SETRAL

SHELL

TOTAL

MOLYKOTE

OPAL

ITECMA

DOW CORNING

ALVANIA R2

ROLEXA 2 MISOLA AHEPONA Z 220EPOXA MO 2 EPONA Z 150

LS EP 2 ENERGOL CRXP 150

SPEEROL EP2

SHF 22ENERGOL CRXP 220

ALPHA SP 150 ALPHA SP 220

EP2 STATERMA MO10

REDUCTELF SP150

REDUCTELF SP220 SPINEF 22

BEACON EP2 SPARTAN EP150

SPARTAN EP220

SPINESSO 22

MARSON EP2 GIRAN SR150 GIRAN SR220

BELLEVILLE N

GRACO AF 309

CENTOPLEX 2 UNISILKON L50Z ALTEMP q.NB50 UNIMOLY GL82 WOLFRACOAT C LAMORA 150 LAMORA 220 CRUCOLAN 22

MOBILUX MOBILGEAR 629 MOBILGEAR 630 DTE 24

LUBRA K LC LUBRA K MP TOP BLENB ISO 80W90

TOP BLENB ISO 220

LUBRA K ATL SAE5W

MISETRAL 43N

RETINA AM OMALA 150 OMALA 220 TELLUS 22

MULTISS EP2 CARTER EP150 CARTER EP220 EqUIVIS 22

MOLYCOTE 44 PATE DX

GEVAIR SP SUPER MOS 2 GEAROPAL GM 65 ISO 150

GEAROPAL GM 75 ISO 220

HYDROPAL HO 110 HM++22

GRL-ULTRA VULCAIN GMO LHT-C AEROSYNDURAGEAR

BL

SH 44 N

MULTI PURPOSE GREASE MOLY

ANTAR

Grade ISO NLGI2 Grade ISO NLGI3 Grade ISO NLGI1 Grade ISO NLGI2 Grade ISO NLGI2 Grade ISO VG150

Grade ISO VG220

Grade ISO VG22

SILUB-P

-4°F + 284°F -40°F + 392°F -4°F + 302°F -4°F + 275°F -22°F + 1292°F 32°F + 212°F 32°F + 248°F +50°F + 149°F


01102046


Lubricant table

MACHINE LUBRICATION

USES

Rolling bearingsBearings

Rolling bearings Bearings hight temperature

Assembly paste(fretting corrosion)

Bare gearsChains shafts ThreadSlides

Flange jointsUnion pipesSteam circuits

Reducers with wheels and screws

Reducers with gears

Circuits and pneumatic devices

TYPES OF LUBRICANTS

AND STANDAR-DIZATION

Lithium soap grease

Lithium soap grease + silicone oil

Lithium soap paste + mineral oil + mineral solid greases

Lithium soap grease with MOS2 additive

Graphite grease mini 60% graphite, special leakproof

Extreme hight pressure oil

Extreme hight pressure oil

Inhibited oil SAE5

TEMPERATURE LIMIT RANGE

CODE PRODUCT

RECOMMENDED

CORRESPONDENCE

0408 110INSTRUCTION

HANDBOOK

01102046

Notice Date Page

Conversion of measurement units The following is a list of correspondences of the main frequently used units, to avoid the need to use measurement unit conversion tables.

bar : 1 bar = 100 000 Pa 1 bar = 1.019 7 kg/cm² 1 bar = 750.06 mm Hg 1 bar = 10 197 mm H2O 1 bar = 14.504 psi british thermal unit : 1 Btu = 1 055.06 J 1 Btu = 0.2521kcal

calorie : 1 cal = 4.185 5 J 1 cal = 10-6 th 1 kcal = 3.967 Btu 1 cal/h = 0.001 163 W 1 kcal/h = 1.163 W

continental horse power :1 ch = 0.735 5 kW 1 ch = 0.987 0 HP

cubic foot : 1 cu ft = 28.316 8 dm³ 1 cu ft = 1 728 cu in

cubic inch : 1 cu in = 16.387 1 dm³

foot : 1 ft = 304.8 mm 1 ft = 12 in

gallon (U.K.) : 1 gal = 4.545 96 dm3 or l 1 gal = 277.41 cu ingallon (U.S.A.) : 1 gal = 3.785 33 dm3 or l 1 gal = 231 cu in

horse power : 1 HP = 0.745 7 kW 1 HP = 1.013 9 ch

inch : 1 in = 25.4 mm

joule : 1 J = 0.000 277 8 Wh 1 J = 0.238 92 cal

kilogramme :1 kg = 2.205 62 lb

kg/cm2 : 1 kg/cm² = 98 066.5 Pa 1 kg/cm² = 0.980 665 bar

1 kg/cm² = 10 000 mm H2O 1 kg/cm² = 735.557 6 mm Hg

pound : 1 lb = 453.592 37 g

meter : 1 m = 1.093 61 yd 1 m = 3.280 83 ft 1 m = 39.37 in

cubic meter :1 m³ = 1 000 dm³ 1 m³ = 35.314 7 cu ft 1 dm³ = 61.024 cu in 1 dm³ = 0.035 3 cu ft

pascal : 1 Pa = 1 N/m² 1 Pa = 0.007 500 6 mm Hg 1 Pa = 0.101 97 mm H2O 1 Pa = 0.010 197 g/cm² 1 Pa = 0.000 145 psi 1 MPa = 10 bar

psi : 1 psi = 0.068 947 6 bar

thermie : 1 th = 1 000 kcal 1 th = 106 cal 1 th = 4.185 5 x 106 J 1 th = 1.162 6 kWh 1 th = 3 967 Btu

watt : 1 W = 1 J/s 1 W = 0.860 11 kcal/hwatt-hour : 1 Wh = 3600 J 1 kWh = 860 kcal

yard : 1 yd = 0.914 4 m 1 yd = 3 ft 1 yd = 36 in

temperature degrees : 0 °K = -273.16 °C 0 °C = 273.16 °K t °C = 5/9 (t °F-32) t °F = 1.8 t °C + 32

10. Appendices

0408 210

9595

9595

70

60

60

50

50

40

40

40

30

30

30

WWW

D1250

D1251

D1252


01102046

Notice Date Page10. Appendices

Explanation of washing symbols

(ISO 3758:2005 standard)

To overcome language barriers, the following are symbols used internationally to give you guidance and recommendations when washing different textiles.

Washing The tub symbolizes washing. Max. washing Mechanical temperature in °C action 95 normal

95 mild

70 normal

60 normal

60 mild

50 normal

50 mild

40 normal

40 mild

40 very mild

30 normal

30 mild

30 very mild

40 Wash by hand

Do not wash

Bleaching The triangle symbolizes bleaching. Bleaching allowed (chlorine or oxygen).

Bleaching allowed (only oxygen).

Do not bleach.

Dry or water The circle symbolizes dry or cleaning water cleaning.

Normal dry cleaning with perchlo- roethyl, solvent of hydrocarb.

Mild dry cleaning with perchlo- roethyl, solvent of hydrocarb.

Normal dry cleaning with solvent of hydrocarb.

Mild dry cleaning with solvent of hydrocarb.

Do not dry clean.

Normal water cleaning.

Mild water cleaning.

Very mild water cleaning.

Drying The circle in a square symbolizes tumble drying. Can be put in a tumble dryer. Normal temperature.

Can be put in a tumble dryer. Lower temperature.

Do not put in a tumble dryer.

Ironing The iron symbolizes the domestic ironing and pressing process. Max.temperature 200°C.

Max.temperature 150°C.

Max. temperature 110°C. The steam can cause irreversible damages.

Do not iron.

Electrolux Laundry Systems Sweden AB341 80 Ljungby, Sweden

www.electrolux.com/professional

Share more of our thinking at www.electrolux.com

Date post:	08-May-2018
Category:	Documents
Upload:	vomien
View:	236 times
Download:	4 times

Operating handbook Feeder Ironer Folder & Stacker...

Documents