OT DMX 6x 350/700 DIM SOOT DMX 12x 350/700 DIM SO
LED dimmer Operating instructions
3
Contents
Safety............................................................................................... 4General.instructions. 4Safety.instructions. 4
Description....................................................................................... 5Purpose,.function.and.application. 5Design. 5
Installation........................................................................................ 6Mounting.the.control.unit. 6Connecting.the.power.supply. 6Connecting.LED.fixtures. 7TP.-.Fixture.Thermal.Protection. 7LED.Wiring.Test. 7Autoload.Detection. 8DRTP.–.Driver.Thermal.Protection. 8
Connecting.DMX.devices. 8
Operation......................................................................................... 9Function.keys. 9Menu.map. 9DMX-512.and.Manual.menu. 10DMX-512.menu. 10Manual.menu. 10
Status.menu. 10Setup.menu. 10Output.status.menu. 11LED.status./.Thermal.status. 11Channel.statistics.. 11
Troubleshooting. 12Technical.data. 13
Appendix........................................................................................ 14Dimensions. 14Derating.curves. 15Cable.type.and.length.limitations. 16
4 IV.2010
OT.DMX.6CH/12CHSafety
SafetyGeneral instructions
The.dimmer.must.only.be.installed.and.put.into.operation.by.a.qualified.electrician.The.applicable.safety.regulations.and.accident.prevention.regulations.must.be.ob-served.
Safety instructions
WARNING!
Exposed,.live.cables.
Danger.of.electric.shock!
•. Only.work.on.the.dimmer.when.it.is.de-energized.
•. Do.not.use.the.dimmer.if.power.cables.are.damaged.
WARNING!
Hot.housing.
Risk.of.burns!
•. Disconnect.the.power.before.installing,.wiring.or.servicing.the.unit.
CAUTION!Destruction.of.the.dimmer.and.other.devices.through.incorrect.mounting!
•. Do.not.hot-plug.ports..Especially.in.larger.LED.matrix.systems,.voltage.potential.differences.in.different.parts.of.the.system.may.damage.ports.when.hot-plugging..Always.turn.off.fixture.supplies.before.connecting.or.disconnecting.
•. Ensure.proper.ventilation.
•. Avoid.areas.where.corrosion,.deteriorating.or.explosive.vapors,.fumes.or.gases.may.be.present.
•. Ensure.that.the.unit.is.securely.attached,.properly.mounted,.and.free.of.excessive.vibration.
•. The.control.unit.is.designed.for.cabinet.installations.only.
•. Only.use.original.accessories.
•. Adhere.to.the.DMX.standard.
CAUTION!Destruction.of.the.dimmer.and.other.devices.through.electrostatic.discharge.(ESD)!
•. Do.not.touch.the.components..
•. Do.all.preparation.work.on.a.static-free.surface..
•. Wear.an.antistatic.wrist.strap.
5
OT.DMX.6CH/12CH
IV.2010
Description
DescriptionPurpose, function and application
The.LED.dimmer.controls.high-power.LED.fixtures.by.a.DMX.signal.using.linear.cur-rent.dimming..It.is.designed.for.use.with.both.high-power.1W.and.3W.LED.fixtures..The.two.versions.6CH.and.12CH.provide.control.over.6.or.12.individual.channels,.which.allows.control.of.2.or.4.highpower.RGB.triplets,.respectively.The.dimmers.can.be.interconnected.to.control.large.installations.by.DMX.signal..Within.a.DMX.network,.connected.highpower.LED.fixtures.can.be.controlled.by.a.central.DMX.controller.(e.g..OSRAM.EASY.DMX.SO).The.dimmer.is.designed.for.installation.on.DIN.rail.in.switch.cabinets.
DesignThe.dimmer.is.made.up.of.the.following.components:•. Power.In.connection.(A)•. DMX.signal.input/output.(B)•. LCD.screen.(C)•. Function.keys.(D)•. LED.outputs.1-4.(E)
CAUTIONHOT
SURFACE
Power In
Constant Current LED Dimmer 350/700mAEMI: EN 55022; EN 55024Safety: EN 60950
NTCCH3CH2CH1
Output 1
6HC CTN4HC 5HC
Output 2
DMX OutDMX In
NTCCH97HC 8HC
Output 3
01HC 11HC 21HC CTN
Output 4
24-48V DC / 9AA73393800ILMade in Israel
DE
C
A B
6 IV.2010
OT.DMX.6CH/12CHInstallation
InstallationMounting the control unit
•. Follow.the.safety.instructions.•. The.dimmer.is.designed.for.installation.on.DIN.rail.in.switch.cabinets.•. The.dimmer.must.be.oriented.with.the.power-in.terminal.block.and.DMX.data.con-nectors.towards.the.top.to.permit.proper.heat.dissipation.
•. Allow.for.proper.distance.of.unit.enclosure.and.wiring.terminals.for.easy.access,.hardware.configuration.and.maintenance.
•. When.installed.in.an.enclosure.utilizing.45.mm.cutouts,.the.front.panel.LCD.of.the.dimmer.stays.visible.while.the.connections.are.concealed.
Connecting the power supply
CAUTION!Destruction.of.the.dimmer.through.incorrect.mounting!
•. Maintain.correct.polarity.
The.Power.In.connections.are.made.using.a.screw.terminal.block.(4.pins,.pitch.5.mm).
•. .Cable.type.and.length.limitations:.see.appendix...Use.at.least.15.AWG.(1.5.mm2).for.mains.connection.
•. Connect.all.4.terminals.of.the.captive.screw.terminal.•. .Select.the.correct.power.supply.unit.(PSU):.
The.PSU.must.be.selected.keeping.in.mind.the.maximum.number.of.serial.LEDs.per.channel.in.the.application,.output.cable.type/length,.and.the.power.rating.needed.to.drive.the.LEDs.at.the.desired.current..See.the.following.table:
No. of LEDs in a series
Total Vf of LEDs (typ.)
Recom.PSU voltage
6CH Dimmer: Minimal PSU Power Rating
12CH Dimmer: Minimal PSU Power Rating
@350 mA @700 mA @350 mA @700 mA1 3.5.V 24.V 10.0.W 20.0.W 20.0.W 40.0.W
2 7.0.V 24.V 18.8.W 37.6.W 37.6.W 75.2.W
3 10.5.V 24.V 26.5.W 53.0.W 53.0.W 106.0.W
6 21.0.V 24.V 50.3.W 100.6.W 100.6.W 201.2.W
9 31.5.V 36.V 72.8.W 145.6.W 145.6.W 291.2.W
12 42.0.V 48.V 92.6.W 185.2.W 185.2.W 370.4.W
After.applying.power.to.the.unit,.the.dimmer.will.perform.a.quick.self-test.for.proper.voltage.from.the.PSU.
7
OT.DMX.6CH/12CH
IV.2010
Installation
If.the.PSU.voltage.is.within.normal.range,.the.message.PSU OK.will.be.displayed.on.the.LCD.screen..Otherwise,.the.message.PSU FAIL.will.be.displayed.and.the.dimmer.will.not.operate.
Connecting LED fixturesLED-wiring.connections.are.made.using.pluggable.terminals.blocks.(8.pins,.pitch.3.5.mm).
Pin 1 Pin 8
•. Cable.type.and.length.limitations:.see.appendix.and.PSU.specific.limitations.•. NTC.=.connection.for.NTC.sensor..If.the.NTC.sensor.is.not.connected,.Fixture.Thermal.Protection.(TP).will.be.disabled.for.that.output.
TP - Fixture Thermal Protection
This.feature.allows.the.unit.to.receive.feedback.about.the.temperature.of.the.connect-ed.fixture..If.the.environment.temperature.causes.the.fixture.to.overheat.(max..allowed.LED.fixture.temperature.is.75.°C),.the.unit.will.lower.the.level.of.the.current.passing.through.the.fixture.until.the.temperature.of.the.fixture.is.stabilized.within.the.allowed.limitations..If.the.environment.temperature.declines,.the.unit.will.raise.the.level.of.the.current.passing.through.the.fixture.
Note:..The.changes.of.current.will.not.affect.the.color.of.the.light,.but.only.its.intensity..The.light.intensity.depends.very.much.on.the.temperature.of.the.LED..For.example,.if.an.LED.driven.at.700.mA.reaches.a.high.temperature,.its.light.output.may.decline.by.half..So,.if.you.lower.the.current.passing.through.this.LED,.you.will.in.fact.get.the.same.light.intensity.while.the.temperature.of.the.LED.will.be.able.to.stabilize.
The.dimmer.has.been.calibrated.using.the.following.NTC.sensor:Thinking Electronics Industrial - TSM2A103F3802RZ
LED Wiring Test
This.unit.has.a.unique.algorithm.for.the.detection.of.load.type.and.wrong.LED.con-nections..It.can.detect,.if.there.is.a.short.circuit.between.the.LED’s.(+).and.(-).lines,.or.mixed.connection.with.a.neighboring.channel.inside.the.terminal.plug.If.the.unit.detects.incorrect.wiring.on.one.of.the.outputs,.that.group.of.channels.will.not.be.operational.until.the.problem.is.fixed..If.during.normal.operation.some.of.the.LEDs.are.reconnected,.the.LED-wiring.test.will.be.initiated.on.that.group.to.which.the.disconnected.channel.belongs.That.way,.LEDs.can.be.hot-plugged.into.the.system..However,.connecting/disconnect-
8 IV.2010
OT.DMX.6CH/12CHInstallation
ing.LEDs.under.power.is.not.recommended..It.is.recommended.to.make.all.connec-tions.first.and.then.to.turn.on.the.power.
Autoload Detection
Each.channel.of.the.dimmer.is.capable.of.auto-detecting.the.LED.load.type.connected.to.it,.and.selecting.the.appropriate.operating.mode.to.control.that.load.
DRTP – Driver Thermal Protection
The.dimmer.has.an.internal.temperature.sensor.allowing.it.to.monitor.the.temperature.of.the.internal.power.circuitry..If,.by.any.reason,.the.external.environment.temperature.exceeds.the.permitted.limit,.the.unit.will.not.permit.the.internal.circuitry.to.overheat.by.reducing.the.output.power..By.doing.so,.it.avoids.driver.malfunction.caused.by.overheating,.while.still.driving.the.LEDs.even.under.worst.conditions.and.preserving.the.lifetime.of.the.dimmer.
Connecting DMX devicesDMX.signal.outputThe.DMX.connections.are.made.using.the.RJ-45.connectors.
Pin DMX In DMX Out1 DMX.–
2 DMX.+
3 DMX.GND
4 N.C.
5 +16.VDC./.0.3.A N.C.
6-8 N.C.
CAUTION!Destruction.of.the.dimmer.and.other.devices.through.incorrect.mounting!
• If onboard 16 VDC power output is not used, make sure that this line is insulated from any other pins!
•. Before.connecting.any.DMX.controller,.refer.to.the.installation.guide.of.the.controller.manufacturer.
The.dimmer.has.an.active.DMX.signal.level.repeater.eliminating.the.need.for.a.DMX.splitter/repeater.when.daisy-chaining.dimmers.together.
Note:..The.onboard.16.VDC.can.be.used.to.supply.power.to.a.DMX.controller.from.the.DMX.In.RJ-45.connector.
9
OT.DMX.6CH/12CH
IV.2010
Operation
OperationFunction keys
The.dimmer.is.equipped.with.following.function.keys:
Key Function▲/▼ Navigate.through.the.options/change.setting.
↲ Enter.sub.menu/confirm.changes..Hold.to.enter.output.status.from.DMX-512.or.manual.modes.
ESC Go.back.to.the.previous.menu/discard.changes...Hold.to.return.from.DMX-512.or.manual.modes.
Menu map
Setup
Menu Map
DMX-512
Manual
Status
Output status
PSU Vdd
Driver temp.
Admin maintenance (PW protected)
Version
Manual edit
DMX setup
LCD contrast
Number of Channels
PW change
Current Rating
Autoaddressing
Address
10 IV.2010
OT.DMX.6CH/12CHOperation
DMX-512 and Manual menuThe.dimmer.can.be.operated.in.the.following.modes:•. DMX-512.mode:.Standard.DMX-512.signal.control.•. Manual.mode:.Static.scene.output..The.channel.values.are.set.manually.in.the.setup.menu.
DMX-512 menu
1st.LCD.line:.DMX-512.Start.address.of.the.dimmer..ADMX.means.that.auto-address-ing.is.enabled.2nd.LCD.line:.Graphic-bar.representation.of.DMX.input.signal.values.
Manual menu
2nd.LCD.line:.Graphic-bar.representation.of.channel.values.which.can.be.set.in.the.setup.menu.
Status menuPSU Vdd
Shows.PSU.voltage.Driver temp.
Temperature.of.the.internal.PCB.of.the.driver.(approx..value,.only.accurate.for.tem-peratures.>.40.°C).Version
Firmware.version.and.current.rating.of.the.driver.(also.shown.after.applying.power.to.the.unit).
Setup menuManual edit
Manually.edit.the.values.of.each.channel.(Manual.mode).1st.line:.Channel.number2nd.line:.Channel.valuePress.↲.to.highlight.the.channel.number.or.channel.value..The.highlighted.option.flashes.DMX setup
• Address:.Change.the.DMX.address.of.the.dimmer.• Autoaddressing:.Enable/disable.the.auto-addressing.function..Press.▲.to.enable.auto-addressing,.press.▼.to.disable.auto-addressing.LCD contrast
Change.the.contrast.level.of.the.LCD.Number of Channels
Limit.the.maximum.number.of.control.channels.from.1.to.6.(6CH).or.1.to.12.(12CH)..This.function.is.designed.to.allow.synchronous.operation.of.several/all.channels.
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
11
OT.DMX.6CH/12CH
IV.2010
Operation
Examples:•. If.the.number.of.channels.is.set.to.6,.the.channels.7-12.will.be.a.copy.of.channels.1-6.
•. If.the.number.of.channels.is.set.to.3,.the.channels.4-6,.7-9,.10-12.will.be.a.copy.of.channels.1-3.
Admin maintenance
Change.the.current.rating..The.current.rating.is.the.maximum.current.in.[mA].that.the.unit.will.output.at.full.(FL).channel.value.
Note:..This.menu.is.password-protected.in.order.to.prevent.accidental.change.of.the.cur-rent.rating..The.default password.is:.512..The.password.can.be.changed.in.the.Password.menu.
Entering.the.password:.The.highlighted.digit.will.flash..Press.▲.and.▼.to.change.the.highlighted.digit..Press.↲.to.highlight.next.digit.• Current Rating:.Set.the.current.rating.from.50.to.700.mA.• Password:.Change.the.password.
Output status menuShows.information.about.the.status.of.connected.fixtures..This.menu.can.be.accessed.by.pressing.and.holding.↲.
LED status / Thermal status
Select.the.desired.output.and.press.↲.• CHXX: OK:.Indicates.that.the.LEDs.connected.to.the.channel.operate.normally.• CHXX: Unplugged:.Indicates.that.no.LEDs.are.connected.to.the.channel.(XX.indicates.number.of.channel,.can.vary.from.1.to.12.)Thermal.status:
Note:..Only.available.on.supported.fixtures.with.thermal.sensors.on-board.
•. fixture.temperature.in.[ºC].•. Thermal.Dimmer.value..Displays.the.percentage.of.output.current.in.reference.to.the.nominal.current.rating.value,.which.is.affected.by.the.thermal.protection..See.“Connecting.LED.fixtures”.
Channel statistics
Select.the.desired.channel.and.press.↲ to.briefly.show.the.channel.statistics.for.a.few.seconds.1st.line:.Channel.drop.voltage.2nd.line:.Channel.driving.current.of.every.channel.
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
DMX: 1 IIIIII
Manual IIIIII
CH1 CH2 CH3 FL 34 68
Address Autoaddre
Contrast Set: 45
Channels No: 6
Password: **2
Current R Password
Output 1 Output 2
CH1: OK CH2: OK
49.9 C 100% Th
V=36.3V I=349mA
12 IV.2010
OT.DMX.6CH/12CHOperation
TroubleshootingIf.you.cannot.remedy.the.fault,.please.contact.the.Customer.Service.department.
Fault Possible cause RemedyDevice.does.not.function. Dimmer.is.not.receiving.
power.from.the.external.DC.power.supply.
Verify.Power.In.connec-tions..Ensure.that.the.AC.circuit.breaker.of.the.PSU.is.not.tripped.
Device.not.responding.to.DMX-512.input.signal.
Dimmer.is.not.in.DMX-512.mode.
Set.dimmer.to.DMX-512.mode.
Bad.DMX-512.wiring.or.DMX-512.signal.is.miss-ing.
Check.DMX-512.wiring.
When.unit.is.receiving.a.correct.DMX-512.signal,.the.icon. .will.blink.at.the.top.right.of.the.LCD.display.
Error.messages.on.LCD.display:
Message Possible cause RemedyOutput x FAULT!!! Possible.wiring.problem.
output.x.Enter.Output.status.menu,.select.the.output.x.and.review.the.status.mes-sages.
In.the.„Output.status“.menu:CHx: Short circuit!!!
Short.circuit.on.channel.x. Check.the.output.wiring.
CHx: Wiring fault!!!
Incorrect.connection.wir-ing.on.channel.x.
Check.the.output.wiring.
Hardware fault!!! Internal.circuitry.malfunc-tion.
Contact.Customer.Service.department.
13
OT.DMX.6CH/12CH
IV.2010
Operation
Technical data
Operating.voltage 24.….48.VDC
Current.consumption 6CH:.max..4.5.A
12CH:.max..9.A
Power.consumption 6CH:.max..180.W
12CH:.max..360.W
Efficiency Up.to.95.%
Heat.dissipation <.20.W
Max..driving.current Adjustable.(50.….700.mA.per.channel)
Output.current.tolerance <.5.%
Load.regulation 1.%
Output.voltage Max..48.VDC
Fixture.output Up.to.12.LEDs.per.channel
Protection.type IP.40,.dry.location
Working.temperature –10.….+40.°C
Storage.temperature –20.….+70.°C
Working.humidity 20.….90.%.RH,.non-condensing
Storage.humidity 10.….90.%.RH,.non-condensing
Color.grades 256.level.(each.color),.in.total.16,770,000.colors
Fixture.protection Open.line,.short.line.and.wrong.interconnection.pro-tection
Output.protection PTC.(positive.temperature.coefficient).auto-recovery.after.fault.condition.is.removed
Thermal.protection.(unit) Reduces.output.current.to.eliminate.unit.overheating
Standards EN.55022,.EN.55024,.EN.60950-1,.EN.61000-3-2,.EN.61000-3-3
Conformity.with.the.relevant.EU.directives.is.confirmed.by.the.CE.symbol.
14 IV.2010
OT.DMX.6CH/12CHAppendix
AppendixDimensions
OT.DMX.6CH14
2 m
m /
5.5
9“
75,4 mm / 2.97“
75,4 mm / 2.97“
58,5
mm
/ 2
.3“
CAUTION
HOT
SURFA
CE
Pow
erIn
OTDMX6x350/700DIM
SOConstantC
urrentLE
DDimmer350/700m
AEMI:EN55022;EN
55024
Safety:EN60950
NTC
1H
C2
HC
3H
C
Output1
6H
CCT
NCH5
CH4
Output2
DMXOut
DMXIn
24-48V
DC/4.5A
A73392C
00IL
MadeinIsrael
OT.DMX.12CH
75,4 mm / 2.97“
272
mm
/ 1
0.7
1“
75,4 mm / 2.97“
58,5
mm
/ 2
.3“
CAUTION
HOT
SURFA
CE
Pow
erIn
ConstantC
urrentLE
DDimmer
350/700m
AEMI:EN55022;EN
55024
Safety:EN60950
NTC
CH3
CH2
CH1
Output1
6H
CCT
N4
HC
5H
COutput2
DMXOut
DMXIn
NTC
CH9
7H
C8
HCOutput3
01H
C11
HC
21H
CCT
N
Output4
24-48V
DC/9A
A73393800IL
MadeinIsrael
15
OT.DMX.6CH/12CH
IV.2010
Appendix
Derating curves
0.00%
10.00%
20.00%
30.00%
40.00%
50.00%
60.00%
70.00%
80.00%
90.00%
100.00%
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44
Effic
ienc
y (%
)
LEDs Vf (V)
Driver's Efficiency vs LEDs Voltage
48V PSU36V PSU24V PSU
0.0%
10.0%
20.0%
30.0%
40.0%
50.0%
60.0%
70.0%
80.0%
90.0%
100.0%
0 10 20 30 40 50 60 70
Out
put L
ED
Pow
er (
%)
Ambient Temperat ure (˚C)
24 V PSU Derating Curve
0.0%
10.0%
20.0%
30.0%
40.0%
50.0%
60.0%
70.0%
80.0%
90.0%
100.0%
0 10 20 30 40 50 60 70
Ou
tput
LE
D P
ow
er (
%)
Ambient Temperat ure (˚C)
36V PSU Derating Curve
0 .0 %
10 .0%
20 .0%
30 .0%
40 .0%
50 .0%
60 .0%
70 .0%
80 .0%
90 .0%
100 .0%
0 10 20 30 40 50 60 70
Out
put L
ED P
ower
(%)
Ambient Temperature (˚C)
48V PSU Derating Curve 1 LED
2 LED
3 LED
4 LED
5 LED
6 LED
7 LED
8 LED
9 LED
10 LED
11 LED
12 LED
16 IV.2010
OT.DMX.6CH/12CHAppendix
Cable type and length limitations
@ 3
50m
A
AWG
C
OPP
ERD
iam
eter
m
m
Ohm
s pe
r km
Max
am
ps
for p
ower
tr
ansm
issi
on
Volta
gedr
op
(100
m,
350
mA
)
max
. LE
Ds
50 m
max
. LE
Ds
100
m
max
. LE
Ds
150
m
max
. LE
Ds
20
0 m
max
. LE
Ds
25
0 m
max
. LE
Ds
30
0 m
max
. LE
Ds
40
0 m
max
. LE
Ds
50
0 m
260.40386
134
0.36.(2.2)
4.69
1210
98
75
3X
240.51054
850.57.(3.5)
2.975
1212
1110
98
65
22.(0.34.mm
2 )0.64516
530.92.(7)
1.855
1212
1211
1110
98
18.(0.75.mm
2 )1.02362
212.3.(16)
0.735
1212
1212
1212
1111
15.(1.5.mm
2 )1.45034
114.7.(28)
0.385
1212
1212
1212
1212
@ 7
00 m
A
AWG
C
OPP
ERD
iam
eter
m
m
Ohm
s pe
r km
Max
am
ps
for p
ower
tr
ansm
issi
on
Volta
gedr
op
(100
m,
350
mA
)
max
. LE
Ds
50 m
max
. LE
Ds
100
m
max
. LE
Ds
150
m
max
. LE
Ds
20
0 m
max
. LE
Ds
25
0 m
max
. LE
Ds
30
0 m
max
. LE
Ds
40
0 m
max
. LE
Ds
50
0 m
260.40386
134
0.36.(2.2)
9.38
1210
85
3X
XX
240.51054
850.57.(3.5)
5.95
1211
108
73
XX
22.(0.34.mm
2 )0.64516
530.92.(7)
3.71
1212
1110
97
53
18.(0.75.mm
2 )1.02362
212.3.(16)
1.47
1212
1211
1111
1010
15.(1.5.mm
2 )1.45034
114.7.(28)
0.77
1212
1212
1111
109
X.=.specified.cable.type./.length.cannot.be.used
OSRAM GmbH.Kunden.Service.Center.Customer-Service-Center.(CSC).Steinerne.Furt.62.86167.Augsburg.GermanyTel.:..+49.(0).1803.677.-.200..(kostenpflichtig./.charges.apply).Fax.:.+49.(0).1803.677.-.202www.osram.comwww.osram.de
IV.2010OT-DMX_6CH_12CH_ba1004en_we1.01.indd
400832157268404008321572684