opticalCON Field Assembly

v1

TOOLS & ACCESSORIES

CABLE

MEASUREMENT

opticalCON Field Assembly

v1

Tools and Accessories Pre-requirements • Certification is valid for 2 years and can be evaluated after that period. • In case of assembly quality issues, Field Assembly certification may be suspended. Cable requirements • Neutrik opticalCON connectors may only be assembled with certified cables. • Neutrik certified cables are listed below. • Additional cable certifications may be requested from customers with Field Assembly certification. • Minimum quantity on strain relief kits will be expected if existing strain reliefs do not match with custom

requested cables. Type Description NO2MX-R-KIT-FA NO2SX-R-KIT-FA

Ruthenium plating, MM PC Ruthenium plating, SM PC

opticalCON DUO; ruthenium plating; multimode PC, single mode PC; strain relief KIT to be ordered separately; includes 2x field assembly LC

NOSR-2C-FA Strain relief kit for 2-ch cables

Cable retention, crimp ferrules, boot (see cable table below).

NOSR-S1-FA Strain relief kit for SMPTE cables

Cable retention, crimp ferrules, boot, pins (see cable table below).

NOSR-S5-FA Strain relief kit for Low – voltage cables

Cable retention, crimp ferrules, boot, pins (see cable table below).

NO2MLC-FA

opticalCON field assembly LC; multimode PC

NO2SLC-FA

opticalCON field assembly LC; single-mode PC

CAS-OPTICALCON-FA

opticalCON Field Assembly case for selftermination.

opticalCON Field Assembly

v1

Tools and Accessories HX-R-BNC

Crimp tool for cable retention, suitable dies DIE-BNC-R-*

DIE-R-OPT* HEX HEX SQUARE DIE-R-OPT3A 6.47 5.41 - DIE-R-OPT3 6.47 5.41 - DIE-R-OPT4 9.73 2.54 1.6 DIE-R-OPT5 7.36 8.23 - Crimp dies to be used with HX-R-BNC crimp tool only. DIE-R-OPT3A offers combined strain relief assembly for low quantities.

HTOPT-S1

opticalCON assembly fixture for cable retention, use together with crimping tool HX-R-BNC plus appropriate die

HTOPT-S2

opticalCON strain relief assembly fixture, use for large quantity production

HTOPT-S3

opticalCON assembly fixture for opticalCON field termination, contains fixture, user manual and technical info.

HTOPT-CS

Cable stripper for HYBRID cables

opticalCON Field Assembly

v1

Tools and Accessories CAS-FOCD opticalCON Fiber Optic Cleaning

Device - contains lint-free wipes, dry cleaning sticks, fiber connector cleaner, fiberscope and adapter

FOCD-CF (refill accessory CAS-FOCD)

Fiber Optic Cleaning Devices –Cleaning Fluid

FOCD-DC250

Dry cleaner 2.5mm for SC, FC,ST

FOCD-DC125

Dry cleaner 2.25mm for LC and MU

FOCD-DW

Lint-free dry wipes for fiber cleaning

CAS-FOMD

Measurement kit for fast system connectivity check - contains power meter SM, attenuator, 2.5mm/1.25mm adapter

FOMD-TC-MM850 FOMD-TC-SM1310 FOMD-TC-SM1550

Transceiver 850nm multimode Transceiver 1310nm single-mode Transceiver 1550nm single-mode)

FOMD-FM-MM FOMD-FM-SM

Fiber meter multimode Fiber meter single-mode 3 digit

opticalCON Field Assembly

v1

Tools and Accessories

Fiber cable type

Cable manufacturer

order #

Cable manufacturer

Cable jacket

Cable OD

DIE Suitable

connector kit Related strain

relief kit

OCC OC-0002036

Gray matt

DUO multimode OCC OC-

0002401

OCC Black shiny

5mm 0.20”

OPT3 NO2MX-R-KIT-FA NOSR-2C-FA

OCC OC-0002037

Gray matt

DUO single-mode OCC OC-

0002402

OCC Black shiny

5mm 0.20”

OPT3 NO2SX-R-KIT-FA NOSR-2C-FA

BELDEN 7804C

Gray matt

DUO SMPTE*

single-mode

BELDEN 7804R

Belden Gray matt

9.2mm 0.36”

OPT4 NO2SX-R-KIT NOSR-S1-FA

OCC OC-0002432

Gray matt

DUO low-voltage single-mode hybrid

OCC OC-0002796

OCC Black shiny

7.3mm 0.30” OPT5 NO2SX-R-KIT-FA

NO2SX-S5-FA

QUAD multimode

BELDEN GMTT204

50/125 Belden

Gray matt

5mm 0.20” OPT3 NO4MX-R-KIT-FA NOSR-4C-FA

QUAD single-mode

BELDEN GMTTA04 E9

Belden Gray matt

5mm 0.20”

OPT3 NO4SX-R-KIT-FA NOSR-4C-FA

*…Not compatible to SMPTE 344M standard. Suitable for indoor (studio) camera links considering specific conditions acc. to IEC 60664-1 like pollution degree 1, over voltage category 1 and rated voltage (max 250Vac / 400Vdc). Contact information - cable manufacturer: OCC- optical cable corporation Concourse Drive 5290 11967 Roanoke, VA 24022-1967 USA www.occfiber.com

Belden Europe Edisonstraat 9 5900 AA Venlo The Netherlands www.belden.com

opticalCON Field Assembly

v1

Cable Datasheets OC-0002036 OC-0002401

Item number OC-0002036 OC-0002401 Number of fibers 2 2 Fiber type multimode multimode Core diameter 50 um 50 um Cladding Diameter 125 um 125 um Primary coating diameter 500 um 500 um Secondary buffer diameter 900 um 900 um Numerical aperture 0.20 0.20 Proof test level 100 kpsi 100 kpsi Wavelength 850 nm/1300 nm 850 nm/ 1300 nm Attenuation 3.0 dB/km (850 nm);

1.0 dB/km (1300 nm) 3.0 dB/km (850 nm); 1.0 dB/km (1300 nm)

Bandwidth 500 MHz/km 500 MHz/km Cable weight 23 kg/km 23 kg/km Cable diameter 5.0 mm 5.0 mm Installation: Max. tensile load 1800N 1800N Min. bend radius 8.0 cm 8.0 cm Operation: Max. tensile load 600N 600N Min. bend radius 4.0 cm 4.0 cm Impact resistance 200 impacts (EIA/TIA-455-25

Military Req.) 200 impacts (EIA/TIA-455-25 Military Req.)

Crush resistance 440 N/cm (TIA/EIA-455-41 military req.)

440 N/cm (TIA/EIA-455-41 military req.)

Operation temperature -55°C to +85°C -55°C to +85° C Storage temperature -70°C to +85°C -70°C to +85°C Cable surface V – jacket C - jacket

opticalCON Field Assembly

v1

Cable Datasheets OC-0002037 OC-0002402

Item number OC-0002037 OC-0002402 Number of fibers 2 2 Fiber type single-mode single-mode Core diameter 8.3 um 8.3 um Cladding Diameter 125 um 125 um Primary coating diameter 500 um 500 um Secondary buffer diameter 900 um 900 um Numerical aperture 0.13 0.13 Proof test level 100 kpsi 100 kpsi Wavelength 1310 nm/ 1550 nm 1310 nm/ 1550 nm Attenuation 0.5 dB/km (1310 nm)

0.5dB/km (1550 nm) 0.5 dB/km (1310 nm) 0.5dB/km (1550 nm)

Nominal zero dispersion slope 0.092 ps/(nm2-km) 0.092 ps/(nm2-km) Cable weight 23 kg/km 23 kg/km Cable diameter 5.0 mm 5.0 mm Installation: Max. tensile load 1800 N 1800 N Min. bend radius 8.0 cm 8.0 cm Operation: Max. tensile load 600 N 600 N Min. bend radius 4.0 cm 4.0 cm Impact resistance 200 impacts (EIA/TIA-455-25

military req.) 200 impacts (EIA/TIA-455-25 military req.)

Crush resistance 440 N/cm (TIA/EIA-455-41 military req.)

440 N/cm (TIA/EIA-455-41 military req.)

Operation temperature -55°C to +85°C -55°C to +85° C Storage temperature -70°C to +85°C -70°C to +85°C Cable surface V – jacket C – jacket

opticalCON Field Assembly

v1

Cable Datasheets Belden 7804C

Item number Belden 7804C Number of fibers 2 Fiber Type Single-mode Core diameter 9.5 um Cladding diameter 125 um Fiber buffer tube diameter 900 um Wavelength 1310 nm Attenuation 0.45 dB/km Cable weight 121 kg/m Cable diameter 9.2 mm Min. bend radius 63.5mm Number of conductors 4 Conductor diameter 0.6 mm (AWG 24)/ 1.49 mm (AWG 16) Conductor insulation diameter 1.27 mm (AWG 24)/ 2.36 mm (AWG 16) Conductor DC resistance AWG 24: 76.4 ohms/1000m AWG 16: 14.1 ohms/1000m Operating temperature -30°C to +60°C Cable surface C-jacket

opticalCON Field Assembly

v1

Cable Datasheets Belden 7804R

Item number Belden 7804C Number of fibers 2 Fiber Type Single-mode Core diameter 9.5 um Cladding diameter 125 um Fiber buffer tube diameter 900 um Wavelength 1310 nm Attenuation 0.45 dB/km Cable weight 121 kg/m Cable diameter 9.2 mm Min. bend radius 63.5mm Number of conductors 4 Nominal core OD 1.27 mm (AWG 24)/ 2.36 mm (AWG 16) Conductor DC resistance AWG 24: 76.4 ohms/1000m AWG 16: 28.9 ohms/1000m Operating temperature -30°C to +60°C Cable surface C-jacket

opticalCON Field Assembly

v1

Cable Datasheets

OCC OC-0002432 OCC OC-0002796

Item number OC-0002032 OC-0002796 Number of fibers 2 2 Fiber type single-mode single-mode Cladding Diameter 125 um 125 um Primary coating diameter 245 um 245 um Secondary buffer diameter 900 um 900 um Proof test level 100 kpsi 100 kpsi Wavelength 1310 nm/ 1550 nm 1310 nm/ 1550 nm Attenuation 0.5 dB/km (1310 nm)

0.5 dB/km (1550 nm) 0.5 dB/km (1310 nm) 0.5 dB/km (1550 nm)

Cable weight 65 kg/km 65 kg/km Cable diameter 7.3 mm 7.3 mm Installation: Max. tensile load 2200 N 2200 N Min. bend radius 12.0 cm 12.0 cm Operation: Max. tensile load 500 N 500 N Min. bend radius 8.0 cm 8.0 cm Impact resistance 200 impacts (EIA/TIA-455-25

military req.) 200 impacts (EIA/TIA-455-25 military req.)

Crush resistance 440 N/cm (TIA/EIA-455-41 military req.)

440 N/cm (TIA/EIA-455-41 military req.)

Operation temperature -40°C to +85°C -40°C to +85° C Storage temperature -55°C to +85°C -55°C to +85°C Cable surface V – jacket C - jacket

opticalCON Field Assembly

v1

Cable Datasheets Belden GMTT204 50/125 Belden GMTTA04 E9

Item number Belden GMTT204 50/125 Belden GMTTA04 E9 Number of fibers 4 4 Fiber type multimode single-mode Cladding Diameter 125 um 125 um Secondary buffer diameter 900 um 900 um Wavelength 1300 nm/ 850 nm 1300 nm/ 850 nm Attenuation 2.3 dB/km (850 nm)

0.6 dB/km (1300 nm) 0.35 dB/km (1310 nm) 0.21 dB/km (1550 nm)

Cable weight 31 kg/km 31 kg/km Cable diameter 5.8 mm 5.8 mm Installation: Max. tensile load 1200 N 1200 N Min. bend radius 10 cm 10 cm Operation: Max. tensile load 800 N 800 N Min. bend radius 10 cm 10 cm Crush resistance 4000 N/m 4000 N/m Operation temperature -55°C to +85°C -55°C to +85° C Storage temperature -70°C to +85°C -70°C to +85°C Cable surface black matt black matt

opticalCON Field Assembly

v1

Pin Assignment The pin assignments are in-house standards. The solder cups in the opticalCON connector are designed for certified cables (see cable matrix). To reduce faults use following pin assignment for each cable.

Belden 7804C:

Wire color Pin number White 1 Red 2 Gray 3

White 4

OCC OC-0002432 OCC OC-0002796

Wire color Pin number Black/White 1 - - - -

White 4

opticalCON Field Assembly

v1

NEUTRIKNO2-4FD[2]

MEASURINGCABLE

FC-ADAPTER TAIL FIBRE100 m / 50 mµ

NEUTRIKNO2-4FD[1]

MEASURINGCABLE

FC-ADAPTER

LIGHTSOURCE

POWERMETER

IN

MM SM

OUT

LAUNCH FIBRE500 m / 50 mµ

NEUTRIKNKO2M-***

DUT

Pin Assignment Attention: The following step shows the measurement system in our in-house production from Neutrik AG. Single-mode Zeroing

Measurement

Multimode Zeroing

NEUTRIKNO2-4FD[1]

MEASURINGCABLE

FC-ADAPTER

LIGHTSOURCE

POWERMETER

IN

MM SM

OUT

LAUNCH FIBRE500 m / 50 mµ

FC-ADAPTER TAIL FIBRE100 m / 50 mµ

MEASURINGCABLE

Measurement

opticalCON Field Assembly

v1

Contact Info Liechtenstein (Headquarters) NEUTRIK AG, Im alten Riet 143, 9494 Schaan T +423 237 24 24, F +423 232 53 93, neutrik@neutrik.com Germany/Netherlands/Denmark/Austria Neutrik Vertriebs GmbH, Felix-Wankel-Strasse 1, 85221 Dachau T +49 8131 28 08 90, info@neutrik.de Great Britain Neutrik (UK) Ltd., Westridge Business Park, Cothey Way Ryde, Isle of Wight PO33 1 QT T +44 1983 811 441, sales@neutrik.co.uk France Neutrik France SARL, Rue du Parchamp 13, 92100 Boulogne-Billancourt T +33 1 41 31 67 50, info@neutrik.fr USA Neutrik USA Inc., 195 Lehigh Avenue, Lakewood, NJ 08701-4527 T +1 732 901 94 88, info@neutrikusa.com Japan Neutrik Limited, Yusen-Higashinihonbashi-Ekimae Bldg., 3-7-19 Higashinihonbashi, Chuo-ku, Tokyo 103 T +81 3 3663 47 33, mail@neutrik.co.jp Hong Kong Neutrik Hong Kong LTD., Workshop 14, 16 Floor, Wah Wai Centre Nr. 38-40 Au Pui Wan Street, Shatin, New Territories T +852 2687 6055, neutrik@neutrik.com.hk China Ningbo Neutrik Electronics Co., Ltd., Shiqi Street, Yinxian Road West Fengjia Villiage, Yinzhou Area, Ningbo, Zhejiang; 315153 T +86 574 88250488 800, neutrik@neutrik.com.cn

www.neutrik.com BDA 264