Date post: | 14-Dec-2015 |
Category: |
Documents |
Upload: | wilson-orellana |
View: | 8 times |
Download: | 3 times |
HUAWEI TECHNOLOGIES CO., LTD.
All rights reserved
www.huawei.com
Internal
ORG001604 Usage of Panorama Drive Test Tool
ISSUE 1.0
HUAWEI TECHNOLOGIES CO., LTD. Page 2All rights reserved
References
Master the method of using Panorama
Drive Test (DT) tool
Master the method of analysis using
Panorama Drive Test (DT) tool
Master the method of simple data
service test using Panorama DT tool
HUAWEI TECHNOLOGIES CO., LTD. Page 3All rights reserved
Chapter 1 Principle of Drive Test System Chapter 1 Principle of Drive Test System
Chapter 2 DT with Panorama Chapter 2 DT with Panorama
Chapter 3 Background Analysis with Panorama Chapter 3 Background Analysis with Panorama
Chapter 4 Precautions in Using Panorama Chapter 4 Precautions in Using Panorama
HUAWEI TECHNOLOGIES CO., LTD. Page 4All rights reserved
Chapter 1 Principle of Drive Test System
Basic structure of the drive test system
Basic test solution of CDMA
Types of CDMA drive test devices
Major test functions of Pilot panorama
HUAWEI TECHNOLOGIES CO., LTD. Page 5All rights reserved
Basic Structure of the Drive Test System
PC
GPS Receiver
Background-processing software
…...
Receiver Receiver Receiver CDMA
Mobile
Call statistics Call drop, blocking and handoff Poor voice quality Unable to receive calls Data rate too low-Using Markov long calls of variable rate t
o test the coverage and frame error rate
-Using short calls to test the access success rate and drop rate
Mobile phone test report FER, Ec/Io Mobile Tx Power Neighbor Cell PN, Rx_level Air interface signaling Protocol recording and decoding (laye
r 3) Accessing, paging, synchronization Forward service, reverse service
HUAWEI TECHNOLOGIES CO., LTD. Page 6All rights reserved
Basic Test Solution of CDMA
Phone + Server based Measurements
Receiver-based Measurements
Phone - based Measurements
RF Test RF Test
Measured byRF Tools
Measured byRF Tools
Voice service test
Data service test
IP & ApplicationLayers
IP & ApplicationLayers
RLP Layer
Test solution
Engineering Parameters
HUAWEI TECHNOLOGIES CO., LTD. Page 7All rights reserved
Types of CDMA Drive Test Devices
Pilot panorama (Dingli Communications Inc.)
WILL TECH(BlueRose,DM2K)
CAIT
AGILENT
HUAWEI TECHNOLOGIES CO., LTD. Page 8All rights reserved
Major Test Functions of Pilot Panorama
Application layer
Voice service test
Data service test
Application
Data collection functions
Functions for displaying various parameter specifications
HUAWEI TECHNOLOGIES CO., LTD. Page 9All rights reserved
Chapter 1 Principle of Drive Test System Chapter 1 Principle of Drive Test System
Chapter 2 DT with Panorama Chapter 2 DT with Panorama
Chapter 3 Background Analysis with Panorama Chapter 3 Background Analysis with Panorama
Chapter 4 Precautions in Using Panorama Chapter 4 Precautions in Using Panorama
HUAWEI TECHNOLOGIES CO., LTD. Page 10All rights reserved
Chapter 2 DT with PanoramaChapter 2 DT with Panorama
2.1 Preparation for voice service2.1 Preparation for voice service
2.2 Test procedure of voice service2.2 Test procedure of voice service
2.3 Preparation for data service2.3 Preparation for data service
2.4 Test procedure of data service2.4 Test procedure of data service
HUAWEI TECHNOLOGIES CO., LTD. Page 11All rights reserved
Equipment Preparations
Notebook computer of high performance
Hardware dongle
CDMA test mobile phone (Qualcomm test mobile phone)
PCMCIA GPS
PCMCIA 2-port-serial card or USB-to-serial converter cable, m
obile phone data cable
HUAWEI TECHNOLOGIES CO., LTD. Page 12All rights reserved
Hardware Connection
Laptop(Windows 98/2000/XP)
USB Port
Serial port
1X Mobile
GPS Receiver
Hardware Dongle
HUAWEI TECHNOLOGIES CO., LTD. Page 13All rights reserved
Working Window
HUAWEI TECHNOLOGIES CO., LTD. Page 14All rights reserved
Creating Project
Definition of project: A project is the basic unit used by Pilot
panorama to manage and maintain all relevant data, including
all test data, map data, base station data and parameter
settings.
Principle for creating a project: There is no special principle for
creating a project. We can adopt a certain relatively
independent area as a project, such as a BSC (MSC) area or a
region (county set), or save calls of different modes as different
projects, such as Markov call and short call.
HUAWEI TECHNOLOGIES CO., LTD. Page 15All rights reserved
Creating Project How to create : File→New Project ; Project description :
Semi-minor axis of the earthSemi-minor axis of the earth
Name of the ellipsoid: Generally China-Xian is used in China.
Name of the ellipsoid: Generally China-Xian is used in China.
Northeast coordinate representation
Northeast coordinate representation Decimal coordinate
representation Decimal coordinate representation
Default valueDefault value
Projection ratio
Projection ratio
DMS ( Degree, Minute and Second ) coordinate representation
DMS ( Degree, Minute and Second ) coordinate representation
Semi-major axis of the earthSemi-major axis of the earth
HUAWEI TECHNOLOGIES CO., LTD. Page 16All rights reserved
Importing Neighborhood Information
Import method: import the neighborhood information in a test file of the fixed format and then into the project via the menu Data→ Import→ Sites.
HUAWEI TECHNOLOGIES CO., LTD. Page 17All rights reserved
Configuring Devices
Enter the setting page directly
via the menu Data→
Configure→ Device or as
shown in the right table.
HUAWEI TECHNOLOGIES CO., LTD. Page 18All rights reserved
Ready Window
HUAWEI TECHNOLOGIES CO., LTD. Page 19All rights reserved
Chapter 2 DT with PanoramaChapter 2 DT with Panorama
2.1 Preparation for voice service2.1 Preparation for voice service
2.2 Test procedure of voice service2.2 Test procedure of voice service
2.3 Preparation for data service2.3 Preparation for data service
2.4 Test procedure of data service2.4 Test procedure of data service
HUAWEI TECHNOLOGIES CO., LTD. Page 20All rights reserved
Creating Call
After the port is set, click Logging→
Connect to create the connection.
After the connection is created, click
Logging→ Start to set the file name to
be saved.
Define the dialing up mode, as shown
in the right figure.
HUAWEI TECHNOLOGIES CO., LTD. Page 21All rights reserved
Testing Windows
HUAWEI TECHNOLOGIES CO., LTD. Page 22All rights reserved
Graph Window By default the parameter displayed is TotalEcIo. Through right-lick/ Field, the parameter displ
ayed can be modified or multiple parameters can be displayed.
HUAWEI TECHNOLOGIES CO., LTD. Page 23All rights reserved
Signaling Window
Number of service neighborhood cells Number of service neighborhood cells
Unlocked PNUnlocked PN
Locked PNLocked PN
The same Sector is differentiated with different Offsets and each is 1/8 chip unit.
The same Sector is differentiated with different Offsets and each is 1/8 chip unit.
Number of multi-pathsNumber of multi-paths
Number of PNs locked by the mobile phoneNumber of PNs locked by the mobile phone
Forward FER of 100 frames Forward FER of 100 frames
HUAWEI TECHNOLOGIES CO., LTD. Page 24All rights reserved
System Parameter Window
HUAWEI TECHNOLOGIES CO., LTD. Page 25All rights reserved
Message Window
The Message window displays Level 3 messages, while the pull-down box below shows the types of the current Level 3 messages. The displayed messages can be filtered through the selection of the tree structure of the Level 3 messages.
HUAWEI TECHNOLOGIES CO., LTD. Page 26All rights reserved
Chapter 2 DT with PanoramaChapter 2 DT with Panorama
2.1 Preparation for voice service2.1 Preparation for voice service
2.2 Test procedure of voice service2.2 Test procedure of voice service
2.3 Preparation for data service2.3 Preparation for data service
2.4 Test procedure of data service2.4 Test procedure of data service
HUAWEI TECHNOLOGIES CO., LTD. Page 27All rights reserved
Hardware Preparations Notebook computer of high performance
Hardware dongle
CDMA test mobile phone (Qualcomm test mobile phone)
PCMCIA GPS
USB4-Port Serial Adapter, mobile phone data cable (with two serial ports)
HUAWEI TECHNOLOGIES CO., LTD. Page 28All rights reserved
Hardware Connection
PC(Windows 98)
USB4-PortSerial Adapter
USB Port
Serial port
1 2 3 4
1X Mobile
GPS Receiver
Used for transmitting data (black)
Used for the drive test software to collect signaling (white)
HUAWEI TECHNOLOGIES CO., LTD. Page 29All rights reserved
Adding and Setting MODEM
In the data service test, the mobile phone is used as a
MODEM. After the mobile phone is connected to the computer,
a new MODEM need be added. During the installation, the
mobile phone driver need be installed and the ports of the
MODEM need be set according to the data port of the mobile
phone.
The highest rate provided by the computer and dual-serial-port
card is 115200Kbps, which will probably become the
bottleneck in 1x test. Therefore, it is recommended to use the
USB-to-serial-port converting device, which will make the rate
of the serial port reach 230400Kbps. Then connect the data
port of the mobile phone to this serial port.
HUAWEI TECHNOLOGIES CO., LTD. Page 30All rights reserved
Adding and Setting MODEM Select the created MODEM, click “Attribute” and set the maximum port rate to
230400. Thus the setting of the MODEM is completed.
HUAWEI TECHNOLOGIES CO., LTD. Page 31All rights reserved
Setting Dialup Network
Create a dialup network. Select the created mobile phone MODEM and set the access number, user name and password.
HUAWEI TECHNOLOGIES CO., LTD. Page 32All rights reserved
Setting Dialup Network
Double-click the created dialup network, select “Attribute”, select the MODEM used by the dialup network
and click “Configure” to set the maximum rate to 230400.
Note: to ensure that he 1x test can be carried out smoothly, the Modem, the dialup network and the mobile
phone shall have the same baud rate of either 230400 or 115200.
HUAWEI TECHNOLOGIES CO., LTD. Page 33All rights reserved
Setting Panorama
Under the software menu, select View→ Data to set the test items to be carried out.
HUAWEI TECHNOLOGIES CO., LTD. Page 34All rights reserved
Chapter 2 DT with PanoramaChapter 2 DT with Panorama
2.1 Preparation for voice service2.1 Preparation for voice service
2.2 Test procedure of voice service2.2 Test procedure of voice service
2.3 Preparation for data service2.3 Preparation for data service
2.4 Test procedure of data service2.4 Test procedure of data service
HUAWEI TECHNOLOGIES CO., LTD. Page 35All rights reserved
Testing Data Service After the device is connected, click “1x Data” in the dialup window to carry out 1x test.
In the popup window “CDMA Data Test”, select the created dialup network in “Dial”, the
serial port connecting the data port of the mobile phone with the computer (the serial port
connecting the MODEM with the computer) in “Port”, as well as the items to be tested in
“Data Configuration”. Then click “OK”. The software will carry out 1x integrated test.
HUAWEI TECHNOLOGIES CO., LTD. Page 36All rights reserved
Testing Data Service During the test, the software will implement Ping, FTP upload/download test and
HTTP download test automatically according to the preset items.
HUAWEI TECHNOLOGIES CO., LTD. Page 37All rights reserved
Testing Data Service
After the test is completed, click “Report”. The test result will be automatically inserted in a Word document in the form of a table.
HUAWEI TECHNOLOGIES CO., LTD. Page 38All rights reserved
Chapter 1 Principle of Drive Test System Chapter 1 Principle of Drive Test System
Chapter 2 DT with Panorama Chapter 2 DT with Panorama
Chapter 3 Background Analysis with Panorama Chapter 3 Background Analysis with Panorama
Chapter 4 Precautions in Using Panorama Chapter 4 Precautions in Using Panorama
HUAWEI TECHNOLOGIES CO., LTD. Page 39All rights reserved
Chapter 3 Background Analysis with Panorama
Analysis of key radio specifications
Analysis of key events
Analysis methods: data review, DT track distribution, statistics,
air interface message analysis
Auxiliary methods: data editing, deletion and combination
Note: The same software is used for both foreground test and background analysis.
HUAWEI TECHNOLOGIES CO., LTD. Page 40All rights reserved
Data Review
Open the project where the data need be reviewed, open the MAP, click to select the
data to be reviewed and display the DT track. Open the Status window by clicking
Meanwhile, Graph, Message and Temporary windows can be opened selectively.
Select the data review in the review tool bar and click the play button to start the review.
HUAWEI TECHNOLOGIES CO., LTD. Page 41All rights reserved
Analysis of Key Radio Specifications
The key specifications include EC/IO, RX, TX, FER and TXADJ. Here EC/IO is taken as an example.
HUAWEI TECHNOLOGIES CO., LTD. Page 42All rights reserved
Analysis of Key Radio Specifications
The statistics of key radio specifications can be conducted in the form of graph. Here the statistics of EC/IO is taken as an example.
HUAWEI TECHNOLOGIES CO., LTD. Page 43All rights reserved
Analysis of Key Events
Key events include: handoff, call drop, which can also be defined by the user. Here call drop is taken as an example.
HUAWEI TECHNOLOGIES CO., LTD. Page 44All rights reserved
Analysis of Key Events
Pilot pollution analysis
HUAWEI TECHNOLOGIES CO., LTD. Page 45All rights reserved
Analysis of Um Port Messages
HUAWEI TECHNOLOGIES CO., LTD. Page 46All rights reserved
Data Processing
Delete and Edit operations can be conducted for the drive test data selectively.
The drive test data can be merged: including the merging of DT files of the same project and the merging of DT files of different projects.
HUAWEI TECHNOLOGIES CO., LTD. Page 47All rights reserved
Chapter 1 Principle of Drive Test System Chapter 1 Principle of Drive Test System
Chapter 2 DT with Panorama Chapter 2 DT with Panorama
Chapter 3 Background Analysis with PanoramaChapter 3 Background Analysis with Panorama
Chapter 4 Precautions in Using Panorama Chapter 4 Precautions in Using Panorama
HUAWEI TECHNOLOGIES CO., LTD. Page 48All rights reserved
Extension of Hardware Dongle
Some types of hardware dongles (blue) have usage time limit and need be extended.
How to extend: Install the hardware dongle and run CUSTOMER.EXE. Click Get ID to get the ID of the hardware dongle and click Config to upgrade.
HUAWEI TECHNOLOGIES CO., LTD. Page 49All rights reserved
Setting Geographical Parameters
Setting the Central Meridian: Its value shall be
related to the test area and can be divided by 3.
Setting False Easting (which indicates the deviant
of the starting point of the default Northeast
coordinate in the X direction): The difference
between the south and north hemispheres need be
taken into consideration.
Setting False Northing (which indicates the deviant
of the starting point of the default Northeast
coordinate in the Y direction): The difference
between the south and north hemispheres need be
taken into consideration.
www.huawei.com
Thank You