25
25504 OS
25504
OS
(A) x 36Wood dowel Ø7.8 X 30mm
(B) x 33Cam bolt (large)
(C) x 33Cam (large)
(D) x 8Hinge
(E) x 48Screw Ø3.5 X 12mm
(F) x 2Magnet
(M) x 20Plastic connector
(N) x 18Plastic cover
(O) x 4Metal plate
(P) x 4Screw Ø3 X 12mm
(Q) x 5Handle
(R) x 5Screw M4x20mm
(S) x 8Shelf pin
(T) x 2Wood dowelØ5.8 X 30mm
(U) x 7Screw Ø3.8 X 35mm
(V) x 3Cam bolt (small)
(W) x 3Cam (small)
(X) x 2Fabric strap
(Y) x 4Metal washer
(Z) x 2Screw Ø4 X 14mm
(Aa) x 2Wall anchor
(Bb) x 3Glue
(G) x 24Screw Ø3 X 16mm
(H) x 4Screw Ø5 X 50mm
(I) x 1Plastic plug
(J) x 1Metal slide (left)
(K) x 1Metal slide (right)
(L) x 12Screw Ø3.5 X 12mm
Upper left side panel 11Upper right side panel 12Upper left side rail 13Upper right side rail 14Upper fixed shelf 15Top panel 16Upper back panel
Middle back panel
17Lower top panel 18
19Bottom 110Drawer stripLower left side panel Lower right side panel Lower left side rail
111
1112211111111363333848
1
11121314
Lower right side rail 15Toe kick16Lower back panel17Upper door panelLower door panelUpper adjustable shelfLower adjustable shelfLeft drawer sideRight drawer sideDrawer back
18
Drawer bottom supportDrawer face
19
Drawer bottom
20
Wood dowel Ø7.8 X 30mm
21
Cam bolt (large)Cam (large)
Screw Ø3.5 X 12mmHinge
222324252627ABCDE
2MagnetF24Screw Ø3 X 16mmG
4Screw Ø5 X 50mmH
Plastic plug 1IMetal slide (left) 1JMetal slide (right) 1KScrew Ø3.5 X 12mm 12LPlastic connector 20MPlastic cover 18NMetal plate
Handle
4OScrew Ø3 X 12mm 4P
5QScrew M4x20mm 5RShelf pinWood dowel Ø5.8 X 30mm
Screw Ø3.8 X 35mm
82
332422
7
ST
UCam bolt (small)VCam(small)WFabric strapXMetal washerScrew Ø4 X 14mmWall anchor
YZAa
3GlueBb
2
3
45
7
8
9
10
11
12
13
1416
17
18
18
19
19
20
21
22
23
24
25
26
27
15
6
160°~185°
1. 2. 3.
4. 5.
how to use the cam lock system
5
(A) x 12 Wood dowel
(Bb) Glue
step 1.
6
1. Instill the glue (Bb) to the wood dowel hole as image shown.2. Insert the wood dowel (A) to the part (1) and (2).3. Attach the cam bolt (B) to part (1) and (2).
(B) x 4 Cam Bolt
A
A
B
BBb
Bb
1
2
step 2.
7
(B) x 6 Cam Bolt
1. Attach the hinge (D) to part (3) and (4) using screw (E).2. Attach the cam bolt (B) to part (3) and (4).
(D) x 4Hinge
(E) x 12Screw Ø3.5 X 12mm
D
D
E
E
B
3
D
D E
E
B
4
step 3.
8
(C) x 6 Cam
(Bb) Glue
1. Instill the glue (Bb) to the wood dowel hole as image shown.2. Attach the two parts (1) and (3) together using the wood dowel (A) and cam bolt (B).3. Attach the two parts (2) and (4) together using the wood dowel (A) and cam bolt (B).4. Tighten all the parts using cam (C) as image shown.
1
C
3
4
2
C
step 4.
9
(G) x 2Screw Ø3 X 16mm
(A) x 4Wood dowel
(B) x 4 Cam bolt
(Bb) Glue
1. Instill the glue (Bb) to the wood dowel hole as image shown.2. Insert the wood dowel (A) to part (5).3. Attach the cam bolt (B) to part (6).4. Attach the magnet (F) to the part (6) using screw (G), attention: please put the magnet face in front of the top (6).
(F) x 1Magnet
56
Bb
A
B
F
G
step 5.
10
(C) x 4 Cam
(Bb) Glue
1. Instill the glue (Bb) to the wood dowel hole as image shown.2. Attach the parts (1), (2) and (5) together as image shown.3. Tighten all the parts using cam (C) as image shown.
C1
5
2
step 6.
11
(C) x 4 Cam
(Bb) Glue
1. Insert the back (7) to the groove of parts (1), (2) and (5).2. Instill the glue (Bb) to the wood dowel hole as image shown.3. Attach the top (6) to the parts using wood dowel (A) and cam bolt (B) as the image shown, make sure the back panel inserted into the groove of the top properly.4. Tighten all the parts with cam (C).5. Attach the cam bolt (B) to part (8).
(B) x 4 Cam Bolt
C
B6
7
81
25
step 7.
12
1. Insert the back (9) to the groove of parts (1), (2) and (5). 2. Insert the plastic plug (I) to the back hole (9) as image shown.3. Instill the glue (Bb) to the wood dowel hole as image shown.4. Attach the part (8) to the parts using wood dowel (A) and screw (H) as image shown, make sure the back panel inserted into the groove of the part (8) properly.5. Cover the cam holes using plastic cover (N).
(H) x 4 Screw Ø5 x 50 mm
(I) x 1 Plastic plug
(Bb) Glue
(N) x 14Plastic cover
I
II
I
II
H
9
8
N
N 1
2
5
step 8.
13
(Bb) Glue
1. Instill the glue (Bb) to the wood dowel hole as image shown.2. Insert the wood dowel (A) to the parts (10) and (11). 3. Attach the magnet (F) to the part (11) using screw (G), please make sure to put the magnet face in the correct side.
(G) x 2Screw Ø3 X 16mm
(A) x 8Wood dowel
(F) x 1Magnet
Bb
Bb
A
A
G10
11
F
step 9.
14
1. Instill the glue (Bb) to the wood dowel hole as image shown.2. Attach the wood dowel (A) and the cam bolt (B) to the parts (12) and (13).3. Attach the metal slide (J) to the part (12) using screw (L).4. Attach the metal slide (K) to the part (13) using screw (L).
(A) x 8Wood dowel
(B) x 6Cam bolt
(J) x 1 Metal Slide (left)
(K) x 1 Metal Slide (right)
(L) x 6Screw Ø3.5 X 12mm
(Bb) Glue
Bb
Bb
A
A
B
BJ
J
K
K
L
L
12
13
(C) x 6 Cam
(Bb) Glue
1. Instill the glue (Bb) to the wood dowel hole as image shown.2. Attach parts (12) and (13) to (10) and (11) using wood dowel (A) and cam bolt (B).3. Tighten all the parts with cam (C).
step 10.
15
C
10
11
12
13
1. Attach the hinge (D) to the parts (14) and (15) using screw (E).2. Insert the cam bolt (B) to the parts (14), (15) and (16).3. Instill the glue (Bb) to the wood dowel hole as image shown.4. Insert the wood dowel (A) to the part (16).5. Attach the parts (14), (15) and (16) together as image shown.
step 11.
16
(A) x 4 Wood dowel
(Bb) Glue
(B) x 9 Cam Bolt
(D) x 4Hinge
(E) x 12Screw Ø3.5 X 12mm
Bb
DE
B
A
14
16
15
(C) x 9 Cam
(Bb) Glue
1. Instill the glue (Bb) to the wood dowel hole as image shown.2. Attach all the parts (14), (15) and (16) together with parts (10), (12) and (13) as image shown.3. Tighten all the parts with cam (C).4. Cover the cam holes using plastic cover (N).
step 12.
17
(N) x 4Plastic cover
C
14
16
15
N
N
1012
13
(C) x 4 Cam
(Bb) Glue
1. Instill the glue (Bb) to the wood dowel hole as image shown.2. Insert the back panel (17) to the groove of parts (10), (12) and (13).3. Attach the two parts which has already assembled in step 7 and step 12 together as image shown, to make sure the back panel (17) inserted into the groove of part (8) properly.4. Tighten all the parts with cam (C).5. Attach the plastic connector (M) to the product using screw (G) as image shown.
(G) x 20Screw Ø3 X 16mm
(M) x 20Plastic connector
step 13.
18
8
G
G
M
M17C
°90
1012
13
step 14.
19
1. Attach the metal plate (O) to the parts (18) and (19) using screw (P).2. Attach the handle (Q) to the parts (18) and (19) using screw (R).
(P) x 4Screw Ø3 X 12mm
(O) x 4Metal plate
(Q) x 4Handle
(R) x 4Screw M4 x 20mm
O
Q
Q
R
R
P
P
18
18
O
Q
R
P
19
O
Q
R
P
19
O
1. Attach the part (18) to the body using the hinge (D) and screw (E).2. You could make adjustment on the hinge if you found any gap difference on the door as image shown.3. Insert the shelf pin (S) to parts (1) and (2).4. Put the shelf (20) into the product as image shown.
(S) x 4Shelf pin
step 15.
20
18
18
20
E
S
(E) x 12Screw Ø3.5 X 12mm
1. Attach the part (19) to the body using the hinge (D) and screw (E).2. You could make adjustment on the hinge if you found any gap difference on the door as image shown.3. Insert the shelf pin (S) to parts (12) and (13).4. Put the shelf (21) into the product as image shown.
step 16.
21
19
19
21
E
S
(S) x 4Shelf pin
(E) x 12Screw Ø3.5 X 12mm
1. Attach the metal slide (J) to the part (22) using screw (L).2. Attach the metal slide (J) to the part (23) using screw (L).3. Instill the glue (Bb) to the wood dowel hole as image shown.4. Insert the wood dowel (T) to the parts (22) and (23).
step 17.
22
Bb
Bb
22 23
K
T
T
L
L
J
(L) x 6Screw Ø3.5 X 12mm
(T) x 2Wood dowelØ5.8 X 30mm
(Bb) Glue
(J) x 1 Metal slide (left)
(K) x 1 Metal slide (right)
1. Attach the parts (22), (23), (24) and (25) together using screw (U).2. Insert the cam bolt (V) to the part (26).
(U) x 5Screw Ø3.8 X 35mm
(V) x 3Cam bolt (small)
step 18.
23
22
25
23
24
26
U
V
(Bb) Glue
1. Insert the drawer bottom (27) to the groove of the parts (22), (23) and (24).2. Instill the glue (Bb) to the wood dowel hole as image shown.3. Attach the drawer face (26) to the parts and make sure the drawer bottom inserted properly into the drawer face groove.4. Tighten all the parts using cam (W).5. Attach the handle (Q) to the part (26) with screw (R).6. Insert the drawer to the product as image shown.
(Q) x 1Handle
(R) x 1Screw M4 x 20mm
(W) x 3Cam(small)
step 19.
24
26
Q26
27
W
R
1. Attach the fabric strap (X) to the part (6) using metal washer (Y) and screw (Z).2. Drilling the hole in the wall using drill Ø6, for better looking, please drill the hole a little lower than the product.3. Knock the wall anchor (Aa) into the hole.4. Attach the fabric strap (X) to the wall anchor using metal washer (Y) and screw (U).
(X) x 2Fabric strap
(Y) x 4Metal washer
(Z) x 2Screw Ø4 X 14mm
(Aa) x 2Wall anchor
(U) x 2Screw Ø3.8 X 35mm
step 20.
25
Wall
XY
ZAa
U
