Modular system comprising of up to 2 racks Voice,Data & wireless convergence system Fully expanded system supports up to a
maximum of 160 ports except IP-Phone and WLAN Phone 120 ports
Each Rack can support up to a maximum of 80 station ports (Keyset/SLI)
Trunk ports capacity Single rack with PRI = 122 ports - w/o PRI
= 80 ports 2 rack with PRI = 216 ports - w/o PRI =
160
OS7200 Overview
Range of new Features Router LAN Switch Security : Firewall,VPN,Packet Filtering Layer2 QoS : 802.1p/q Layer3 QoS : CBQ, RTP Priority Queuing Long Distance Ethernet : VDSL DSLAM IP UMS(VM,AA,TTS,Voice recording,E-mail) SIP Server VoIP WEB based Management Multi WLI card support Including 500Premium function
OS7200 Overview
OS7200 - Main Rack system Floor, Wall or Rack Mountable 5 universal card slots RJ45 modulor Interface dedicated MCP slot - slot 6 Supports maximum of 80 station ports
with 1 PSUs Large LCD Phone support 24port with
1PSUs 3 WLI card support
OS7200 Overview
OS7200 Expansion rack - 2 Racks Floor, Wall or Rack Mountable 10 universal card slots Slot 1 in first cabinet used for LCP card Second Rack is controlled by LCP card
installed in dedicated MCP/LCP slot - slot 6
Supports maximum of 160 station ports
E1/PRI card support in slot3 Large LCD Phone support 48port
OS7200 Overview
Memory/Software System Operating software is stored on
a 16 Megabyte Smart Media Card System boots from 512kbytes ROM and
downloads to: 32Mbytes of DRAM
Customer Database is stored in: 4 Meg of SRAM
Smart Media
• NAND Flash• Standard Data Structure• OS: DOS/FAT File system • Used to write data from Memory to Flash• 16MB SmartMedia(TM) is used for OS7200. • Dimension : 37.0(w) x 45.1(L) x 0.76(H) (mm)
Benefits Easy Program Upgrade(No EPROMs required) - Locally & Remotely Easy Back Up of Customer DataBase - Safe from the data loss in power failure Programs installed on Smart Media include: - MCP,LCP,TEPRI Pre-Install Available in your office - Useful for same category site installation
OS7200 Overview
MicroprocessorsLocation Processor Level Function
MCP Motorola MPC855T 32 bit running at 50Mhz
Primary Provides all processing for a Main rack system
LCP Motorola MC 68302 16 bit running at 16 MHz
Secondary Provides local control of Expansion rack
WIM Motorola MPC 8250 64 bit running at 300 MHz
Routing Provides Router function between the WAN and Local LAN
MGI ARM core 32bit running at 50MHz
Gateway Provides Gateway unction between Voice and Data
TEPRI Motorola MC 68302 16 bit running at 16 MHz
Digital trunk Provides Digital Trunk function
Keyset
Hiachi H8 Tertiary Provides data communication within the system
OS7200 Overview
Programming Self Configuring (w/o WIM) MCP assigns Default Numbering Plan
3 or 4 digits according to setting on MCP Card
Flexible numbering plan Programming
via keyset PC - using windows based DPAP-PCMMC 4 levels - Technician, System Administrator,
station user plus via PROG key local and remote programming via LAN
OS7200 System Capacities
Voice Switch . . Trunk/Station : Max. 216ch (PRI : 30ch) . Common Resource : MFS/R, R2CID, Miscellaneous
LAN Switch . Max. 128port
Slots . 32ch slot : 4 slot ( Main rack 3slot/Expansion rack 1slot) . 16ch slot : 6 slot . WIM card : Slot1 per each Rack . LIM card : slot2-5 per each RackSystem IO Serial Communication Port ( Async.) ) . Main : 1 Ports ( MCP ) . Expansion : 1 Ports ( LCP ) LAN . Speed : 10/100 MBPS . Physical Connection : RJ-45 ( 1 Port ) . Built in LAN Board
OS7200 System Capacities
Common Resources .Main . Shelf #1 : DTMF receiver 4Ch, DTMF sender 32Ch, Conference 5 party x 6 groups
.Optional Daughter boards . MFM : DTMF receiver 12ch . RCM : R2 sender 30ch, R2 receiver 8ch. Caller ID receiver 14ch. . RCM2 : Caller ID Sender . MIS : External music 2port, Paging 1port, Loud bell 1port Common bell 1port, Dry contact 2port . Installed maximum - 1EA/MCP
Miscellaneous Functions . Basic : Internal music 1 Port ( MCP ) . Expansion : MIS x 1 ( 1EA/MCP )
SolutionSolution
AdminAdmin
WLAN AP
SMESME
PC ConsoleSmart CallContact CenterVideo Conferencing
Web BrowserSystem MasterPhone ManagerFast Ethernet
Mail ServerInstant Messaging SIP ServerVoIP-UMS LiteVoIP-UMS Pro
FeatureFeatureFast Ethernet
Fast EthernetBranch Office
VPN Tunnel
VoWLAN Phone
WLAN IP Phone LDE Modem
xDSL, Metro Ethernet, VoIP, TDM, etc.
IP-VDSL
Home Working
Operator Network
IP Phones
Digital Phones
Highly Integrated “All-in-one” converged solutionfor total business communication
OS7200 System
OS7200 Hardware
OS7200 Rack
Common Rack for use as main rack or expansion rack
FAN reduce a heating problem Slots 1-5 universal slots
Main rack Slots 3-5 assigned 32 time slots Expansion rack Slots 3 assigned 32 time slots Other slot assigned 16 time slots
Slot 0 dedicated for Processor cards (MCP or LCP)
AC power switches DC (battery back up)
OS7200 Rack Configuration
Front View of the Expansion Rack
Front View of the Main Rack
Slot 0Slot 1 Slot 2
Slot 3Slot 4 Slot 5
Slot 0Slot 1 Slot 2
Slot 3Slot 4 Slot 5
Cabinet Slot Mountable Boards
Main Rack(OfficeServ- Access)
Slot 0 MCP only
Slot 1 All boards except for MCP, LCP, TEPRI, and LIM
Slot 2 All boards except for MCP, LCP, TEPRI, and WIM
Slot 3,4,5 All boards except for MCP, LCP, and WIM
ExpansionRack(OfficeServ- Expansion)
Slot 0 LCP only
Slot 1 All boards except for MCP, LCP, TEPRI, and LIM.
Slot 2
Slot 3 All boards except for MCP, LCP, and WIM
Slot 4 All boards except for MCP, LCP, TEPRI, and WIM
Slot 5
Power Supplies
1 PSUs can be installed in each rack PSU must be installed in backplane PSU provides the several voltage supply to the rack PSU supports 80 station ports or Station Equipment
Power Units (SEPU) No redundancy Power to is controlled by Thermal sensor If the FAN module stoped, System halt after 24 hours.
Total power units of installed cards: 32+32+32+12+0 = 108. - Slot1 used Large LCD Phone 8 port and 2line LCD Phone 8
port. - Slot2 used Large LCD Phone 8 port and 2line LCD Phone 8
port. - Slot3 used Large LCD Phone 8 port and 2line LCD Phone 8
port. - Slot4 used WBS24 Combo 4 portsto power the keysets
connected to 16DLI cards. If 16DLI over 8port Large LCD Phone, Power of 16DLI card
stop.
OS7200 Processor Cards
Main Control Processor - MCP
Installed in slot 0 of the main rack Has the following features:
256 time slot switch matrix Smart Media Card slot 3 Daughter board positions Memory Backup Switch 8 Position Dip Switch Reset button 4 Status LEDS Internal MOH source 1 SIO data rate adaptors 3 x RJ45 STP connected to LCP card
MFM
RCM
MIS
Main Control Processor - MCP
S3
S2
CHARGE
Off
Main Control Processor - MCP
DIP SWITCH USE on the OS7200 MCP
ON (left) OFF (right)
4 Digit Trunk Numbers SW8 3 Digit Trunk Numbers
4 Digit Station Groups SW7 3 Digit Station Groups
4 Digit Station Numbers SW6 3 Digit Station Numbers
Automatic Program Download on power up
SW5
Country Select SW4 Country Select
Country Select SW3 Country Select
Country Select SW2 Country Select
Country Select SW 1 Country Select
4 3 2 1 Country
OFF OFF OFF OFF Korea
OFF OFF OFF ON USA
OFF OFF ON OFF UK
OFF OFF ON ON Italy
OFF ON OFF OFF Australia
OFF ON OFF ON New Zealand
OFF ON ON OFF Holland
OFF ON ON ON Denmark
Ports & LEDs Function Description
LINK1~LINK3 Ports that connect the MCP with the LCP.
MISC1~MISC2 Ports that connect external music sources, paging device, loud bell, common bell, or door bell.
SmartMedia Port for installing the NAND-type flash memory.
LAN Port for establishing the 10Base-T/100Base-Tx Ethernet connection.
SIO UART port(for tests).
RST Button for resetting the MCP board.
RUN LED This LED indicates the status of the MCP. ( - On : Booting./- Blink : The program is operating)
LAN LED - On : MCP is connected LAN.- Blink : MCP is transmitting or receiving Data through LAN port.
SM LED - On : The SmartMedia is installed, however is not accessed.- Blink : The SmartMedia is installed and is being accessed.
LCP LED This LED indicates the status of signaling message processing. - On : Messages are being sent/received to/from the LCP.
Main Control Processor - MCP
Local Control Processor - LCP
Installed in Slot 0 of Expansion rack Has the following features:
2 status LEDs for LCP operation 3 x RJ45 STP Connector for Connection
to MCP and LCP card Supplied with LINK cable
Local Control Processor - LCP
Ports & LEDs Function
LINK1~LINK3 Ports that connect the MCP with the LCP.
SIO UART port(for tests).
RST Button for resetting the LCP board.
RUN LED This LED indicates the status of the LCP.- Off : Power is not connected.- On : Booting.- Blink : The RAM program is operating.
MCP LED This LED indicates the status of signaling message processing.
- Off : There’s no message exchange between MCP and LCP.- On : Messages are being sent/received to/from the MCP.
Local Control Processor - LCP
LINK1 LINK3
LINK2
Link Cable
Connecting MCP Board to LCP Board
Processor Daughter Boards
Multi- Frequency Module - MFM
Installs in any daughter board position of the MCP cards. - maximum of 1 per processor card
Provides 12 DSPs for DTMF and Tone Detection SLT ports or DISA trunks
Multi- Frequency Module - MFM
P1
U7 U4U5
P2
U2
U1
U6
U3
R2/CID Module - RCM
Installs into any of the MCP Cards Consists of the following:
14 CID receivers for CID trunks 30 R2 MFC senders and 8 receivers 8CID and 4R2 MFC
R2/CID Module - RCM
P2
U3
U4
P1
U1
U8
U5
U9
U2
Miscellaneous Function Module - MIS Installs in the following positions:
MCP - Main Rack systems only 2 x RJ-45 sockets Consists of the following:
2 External Music sources 1 External paging audio output 1 loud bell relay audio output 1 common bell relay contact closure 2 software assigned relay contact closures
Miscellaneous Function Module - MIS
Dry contact #1(For common bell)
Dry contact #3(For external page)
External Page Equipment
Additional Page Equipment
MISC 1
MISC 2
Dry contact #2(For external page)
Connecting External/Additional Page Equipment
MOH/BGM source of a user
MOH/BGM source of a userMISC 1
MISC 2
Miscellaneous Function Module - MIS
Trunk Cards
8TRK card
Trunk - 8 loop start trunks 8 Trunk Caller ID path support Performs Polarity Reverse
Detection(PRD) - option Performs Metering Pulse
Detection(MPD) - option
Ports & LEDs
Function Description
P1~P8 Trunk ports.
P1~P8 LED These LEDs indicate the status of the ports.- Off : The trunk line is not being used.- On : The trunk line is being used.- Blink : The ring is being connected.
8TRK card
P1-P8 Port(RJ-45)(RJ-45)
PinNo. 1 2 3 4 5 6 7 8
Function - - - C.O. TIP C.O. RING
- - -
8TRK card
Connecting Common C.O. Lines
TEPRI Card
This card may be configured for PRI or E1 operation. Supports Q-signalling in OS7200 system Must be installed in slots 3-5 in main rack
maximum of 4 per system Do not install this card with the power ON Supports the following features
8 Status LEDs 1 x RJ-45 Sockets for PRI or E1 1 x RJ45 connector to allow upload of TEPRI
software directly to the Card - generally not required
Reset Button - to reset the card 8 position switch to set card operation
TEPRI Card
TEPRI CardTEPRI CARD DIP SWITCH Settings
Switch No. ON OFF Description
1 T1 E1 Selects whether T1 or E1
2 PRI T1 or E1 Selects whether PRI or not
3 Not used
4 NETWORK USER Select Network or User
5 Not used
6 Not used
7 Not used
8 Always ON This switch must always be ON as it is used for Card ID
Switch Settings for PRI/E1 operation
Switch No. PRI Operation E1 Operation 1 OFF OFF 2 ON OFF 3 OFF OFF 4 OFF ON for Master OFF for
Slave (Note) 5 OFF OFF 6 OFF OFF 7 OFF OFF 8 ON ON
Note: When networking OS7200 systems one system must be designated the master (NETWORK) and the other the slave(USER)
TEPRI Card
T1/E1/PRI Port(RJ-45)
Pin No. 1 2 3 4 5 6 7 8
T1 Function Rx+ Rx- - Tx+ Tx- - - -
E1/PRI Function - - - Tx+ Tx- - Rx+ Rx-
Ports & LEDs Function Description
T1/E1/PRI Ports that connect the T1/E1/PRI cable.
SIO UART port(for tests).
RST Button for resetting the TEPRI board.
SYNC LED - On : Clocks are not synchronized when they inter-work with the counterpart station.
- Off : Clocks are synchronized when they inter-work with the counterpart station.
LOS LED - On : Signals have been lost.- Off : Signals have not been lost.
AIS LED - On : The remote alarm has been generated.- Off : The remote alarm has not been generated.
L2 LED This LED indicates the operation status of Layer 2- On : The PRI Layer2 is operating properly. - Off : The PRI Layer2 is operating abnormally.
IPC LED This LED indicates that this board is inter-working with the higher-level module.- On : The board is inter-working with the MCP/LCP.- Off : The board is not inter-working with the MCP/LCP.
CLK LED This LED indicates whether this board is a master or slave.- On : The board has received the synchronization clock from the counterpart station.- Off : The board has sent the synchronization clock to the counterpart station
TP1 LED This LED indicates whether the T1 is established.- This LED turns on once the T1 is established.
TP2 LED This LED indicates whether the PRI is connected. - This LED turns on once the PRI is connected
TEPRI Card
IP Telephony Module - MGI
Provides 0 VoIP channels expandable to 16 using MGI2D
daughter cards Each MGI2D card support 4ch voice/fax H.323/ SIP G.711/G.723.1/G.729 voice compression protocols
Installed in any universal card slot with power OFF Supports the following features
8 Status LEDs RJ-45 10/100 base-T LAN connection 1 x RJ45 connector to allow upload of TEPRI
software directly to the Card - generally not required
Reset Button - to reset the card
MGI Card
Option4
MGI2D
Option3
MGI2D
Option2
MGI2D
Option1
MGI2D
OFF : No memory backup
ON : Available for memory backup (base default value)
