OTHER SYSTEM – CLOCK OT–1
OT
BODY ELECTRICALOTHER SYSTEMCLOCKCOMPONENTS
CLOCK ASSEMBLY
MULTI-DISPLAY ASSEMBLY
UPPER INSTRUMENT PANEL FINISH PANEL
SUB-ASSEMBLY
NO. 3 INSTRUMENT PANEL
REGISTER ASSEMBLY
NO. 4 INSTRUMENT PANEL
REGISTER ASSEMBLY
NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
B131355E02
OT–2 OTHER SYSTEM – CLOCK
OT
REMOVAL1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINALCAUTION:Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (See page IP-5)
3. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY (See page IP-6)
4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (See page IP-6)
5. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (See page IP-6)
6. REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY (See page IP-6)
7. REMOVE MULTI-DISPLAY ASSEMBLY8. REMOVE CLOCK ASSEMBLY
(a) Detach the 2 claws and remove the clock.
INSTALLATION1. INSTALL CLOCK ASSEMBLY
(a) Attach the 2 claws to install the clock.
2. INSTALL MULTI-DISPLAY ASSEMBLY3. INSTALL NO. 4 INSTRUMENT PANEL REGISTER
ASSEMBLY (See page IP-12)4. INSTALL UPPER INSTRUMENT PANEL FINISH
PANEL SUB-ASSEMBLY (See page IP-13)5. INSTALL LOWER INSTRUMENT PANEL FINISH
PANEL SUB-ASSEMBLY (See page IP-13)6. INSTALL NO. 3 INSTRUMENT PANEL REGISTER
ASSEMBLY (See page IP-13)7. INSTALL NO. 1 INSTRUMENT PANEL REGISTER
ASSEMBLY (See page IP-13)8. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
B074089E04
B074089E05
OTHER SYSTEM – CLOCK OT–3
OT
9. PERFORM INITIALIZATION(a) Perform initialization (see page IN-32).
NOTICE:Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
10. CHECK SRS WARNING LIGHT(a) Check the SRS warning light (see page RS-31).
OT–4 OTHER SYSTEM – TELLTALE LIGHT
OT
BODY ELECTRICALOTHER SYSTEMTELLTALE LIGHTCOMPONENTS
INSTRUMENT PANEL SUB-ASSEMBLY
: Specified torqueN*m (kgf*cm, ft.*lbf)
20 (204, 15)
NO. 1 INSTRUMENT PANEL SPEAKER PANEL
SUB-ASSEMBLY (w/ JBL Sound System)
FRONT PILLAR GARNISH RH
FRONT PILLAR GARNISH CORNER PIECE RHFRONT PILLAR GARNISH LH
FRONT PILLAR GARNISH CORNER PIECE LH
CLOCK ASSEMBLY
INSTRUMENT CLUSTER FINISH PANEL END
MULTI-DISPLAY ASSEMBLY
A
A
D
D
D
B126622E03
OTHER SYSTEM – TELLTALE LIGHT OT–5
OT
GLOVE COMPARTMENT DOOR
GLOVE COMPARTMENT DOOR ASSEMBLY
GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
INSTRUMENT PANEL HOLE COVER
LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
NO. 2 INSTRUMENT PANEL
REGISTER ASSEMBLY
NO. 3 INSTRUMENT PANEL REGISTER
ASSEMBLY
NO. 4 INSTRUMENT PANEL REGISTER
ASSEMBLY
UPPER INSTRUMENT PANEL FINISH PANEL
SUB-ASSEMBLY
INSTRUMENT PANEL HOLE COVER
EE
INSTRUMENT PANEL CUSHION
B126623E04
OT–6 OTHER SYSTEM – TELLTALE LIGHT
OT
INSTRUMENT PANEL SUB-ASSEMBLY
TELLTALE LIGHT ASSEMBLY
B132483E01
OTHER SYSTEM – TELLTALE LIGHT OT–7
OT
REMOVAL1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINALCAUTION:Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY(a) Remove the instrument panel (see page IP-5).
3. REMOVE TELLTALE LIGHT ASSEMBLY(a) Disconnect the connector.(b) Detach the 2 claws and remove the telltale light.
INSTALLATION1. INSTALL TELLTALE LIGHT ASSEMBLY
(a) Attach the 2 claws to install the telltale light.(b) Connect the connector.
2. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY(a) Install the instrument panel (see page IP-11).
3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
4. PERFORM INITIALIZATION(a) Perform initialization (see page IN-32).
NOTICE:Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
5. CHECK SRS WARNING LIGHT(a) Check the SRS warning light (see page RS-31).
2 Claws B074056E04
2 Claws B074056E05
OT–8 OTHER SYSTEM – POWER OUTLET SOCKET
OT
BODY ELECTRICALOTHER SYSTEMPOWER OUTLET SOCKETCOMPONENTS
POWER OUTLET SOCKET ASSEMBLY
POWER OUTLET SOCKET COVER
B136398E01
OTHER SYSTEM – POWER OUTLET SOCKET OT–9
OT
REMOVAL1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINALCAUTION:Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2. REMOVE POWER OUTLET SOCKET ASSEMBLY(a) Detach the claw to remove the power outlet socket.
I038883E02
OT–10 OTHER SYSTEM – POWER OUTLET SOCKET
OT
INSTALLATION1. INSTALL POWER OUTLET SOCKET ASSEMBLY
(a) Align the power outlet socket and power outlet socket cover. Insert them from the front side into the vehicle body and install the power outlet socket.
2. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
3. PERFORM INITIALIZATION(a) Perform initialization (see page IN-32).
NOTICE:Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
OT–10 OTHER SYSTEM – REAR POWER OUTLET SOCKET
OT
BODY ELECTRICALOTHER SYSTEMREAR POWER OUTLET SOCKETCOMPONENTS
REAR POWER OUTLET SOCKET ASSEMBLY
POWER OUTLET SOCKET COVER
B136399E01
OTHER SYSTEM – REAR POWER OUTLET SOCKET OT–11
OT
REMOVAL1. REMOVE REAR POWER OUTLET SOCKET
ASSEMBLY(a) Detach the claw to remove the rear power outlet
socket.
I038884E02
OT–12 OTHER SYSTEM – REAR POWER OUTLET SOCKET
OT
INSTALLATION1. INSTALL REAR POWER OUTLET SOCKET
ASSEMBLY(a) Align the rear power outlet socket assembly and
power outlet socket cover. Insert them from the front side into the vehicle body and install the rear power outlet socket assembly.
2. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
3. PERFORM INITIALIZATION(a) Perform initialization (see page IN-32).
NOTICE:Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.