Cisco 7600 Series RouOL-5052-15
C H A P T E R 2
Overview: Cisco 7600 Series SIPsThis chapter describes the SPA interface processors (SIPs) that are supported on the Cisco 7600 series routers and contains the following sections:
• SIP Summary, page 2-1
• Identifying Slots and Subslots for SIPs and SPAs, page 2-2
• Cisco 7600 SIP-200 Overview, page 2-5
• Cisco 7600 SIP-400 Overview, page 2-8
• Cisco 7600 SIP-600 Overview, page 2-23
• Cisco 7600 SSC-400 Overview, page 2-39
SIP SummarySummary descriptions of the SIPs that are supported on the Cisco 7600 series routers are shown in Table 2-1.
Note The Description column indicates the aggregate bandwidth supported by the SIP across all subslots—not per SPA subslot.
Table 2-1 SIP Summary
SIP Product Number Description
Maximum Number of SPAs
Minimum Cisco IOS Release
Cisco 7600 SIP-200 7600-SIP-200 622-Mbps SPA interface processor
4 12.2(18)SXE
Cisco 7600 SIP-400 7600-SIP-400 2.5-Gbps SPA interface processor
4 12.2(18)SXE
Cisco 7600 SIP-600 7600-SIP-600 1 x 10-Gbps SPA Interface Processor
1 12.2(18)SXF
Cisco 7600 SSC-400 7600-SSC-400 SPA services carrier 2 12.2(18)SXE2
2-1ter SIP, SSC, and SPA Hardware Installation Guide
Chapter 2 Overview: Cisco 7600 Series SIPs Identifying Slots and Subslots for SIPs and SPAs
Checking Hardware and Software CompatibilityTo check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether SIPs or SPAs within a system are compatible, but it does provide the minimum Cisco IOS requirements for individual hardware modules or components.
Note Access to this tool is limited to users with Cisco.com login accounts.
To access Software Advisor, click Login at Cisco.com, type “Software Advisor” in the SEARCH box, and click GO. Click the link for the Software Advisor tool.
Choose a product family or enter a specific product number to search for the minimum supported software release needed for your hardware.
Identifying Slots and Subslots for SIPs and SPAsThis section describes how to specify the physical locations of a SIP and SPA on the Cisco 7600 series routers within the command-line interface (CLI) to configure or monitor those devices.
Note For simplicity, any reference to “SIP” in this section also applies to the SSC.
Specifying the Slot Location for a SIP or SSC
The Cisco 7600 series router supports different chassis models, each of which supports a certain number of chassis slots.
Note The Cisco 7600 series router SIPs are not supported with a Supervisor Engine 1, Supervisor Engine 1A, Supervisor Engine 2, or Supervisor Engine 720-3A.
2-2Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Identifying Slots and Subslots for SIPs and SPAs
Figure 2-1 shows an example of a SIP installed in slot 6 on a Cisco 7609 router. The Cisco 7609 router has nine vertically-oriented chassis slots, which are numbered 1 to 9 from right to left.
Figure 2-1 SIP and SPA Installed in a Cisco 7609 Router
Figure 2-2 shows an example of a SIP installed in slot 6 on a Catalyst 6509 switch. The Catalyst 6509 switch has nine horizontally-oriented chassis slots, which are numbered 1 to 9 from right to left.
Figure 2-2 SIP and SPA Installed in a Catalyst 6509 Switch
1290
06
INPUTOK
FANOK
OUTPUTFAIL
o
INPUTOK
FANOK
OUTPUTFAIL
o
SU
PE
RV
ISO
R2
WS
-X6K
-SU
P2-2G
E
STATUSSYSTEMCONSO
LEPWR M
GM
T
RESET
CO
NS
OLE
CO
NS
OLE
PO
RT
MO
DE
PC
MC
IAE
JEC
T
PO
RT
1P
OR
T 2
Sw
itch Load 100%
1%
LINKLINK
SU
PE
RV
ISO
R2
WS
-X6K
-SU
P2-2G
E
STATUSSYSTEMCONSO
LEPWR M
GM
T
RESET
CO
NS
OLE
CO
NS
OLE
PO
RT
MO
DE
PC
MC
IAE
JEC
T
PO
RT
1P
OR
T 2
Sw
itch Load 100%
1%
LINKLINK
SW
ITC
H F
AB
RIC
MD
L STATUS
SELECT
NEXT
WS
-C6500-S
FM
ACTIVE
OC
12 PO
S M
M
OS
M-40C
12-PO
S-M
M
STATUS
12
34RESET
LINK1
LINK2
LINK3
LINK4
CARRIER
ALARM
ACTIVE
TXRX
TX
PORT 1
RX
CARRIER
ALARM
ACTIVE
TXRX
TX
PORT 2
RX
CARRIER
ALARM
ACTIVE
TXRX
TX
PORT 3
RX
CARRIER
ALARM
ACTIVE
TXRX
TX
RX
OC
12 PO
S M
M
OS
M-40C
12-PO
S-M
M
STATUS
12
34RESET
LINK1
LINK2
LINK3
LINK4
CARRIER
ALARM
ACTIVE
TXRX
TX
PORT 1
RX
CARRIER
ALARM
ACTIVE
TXRX
TX
PORT 2
RX
CARRIER
ALARM
ACTIVE
TXRX
TX
PORT 3
RX
CARRIER
ALARM
ACTIVE
TXRX
TX
RX
OC
12 PO
S M
M
OS
M-40C
12-PO
S-M
M
STATUS
12
34RESET
LINK1
LINK2
LINK3
LINK4
CARRIER
ALARM
ACTIVE
TXRX
TX
PORT 1
RX
CARRIER
ALARM
ACTIVE
TXRX
TX
PORT 2
RX
CARRIER
ALARM
ACTIVE
TXRX
TX
PORT 3
RX
CARRIER
ALARM
ACTIVE
TXRX
TX
RX
8 P
OR
T O
C3 P
OS
MM
OS
M-8
OC
3-P
OS
MM
STATUS
1
1
2
2
3
3
1
2
3
4
4
4
RESET
LINK
CARRIER
ALARM
LINK
LINK
LINK
LINK
5
6
7
8
8 P
OR
T O
C3 P
OS
MM
OS
M-8
OC
3-P
OS
MM
STATUS
1
1
2
2
3
3
1
2
3
4
4
4
RESET
LINK
CARRIER
ALARM
LINK
LINK
LINK
LINK
5
6
7
8
STATUS
2
0
3
1
SPA INTER
FACE
PROC
ESSOR
7600-SIP
-200
LINKCARRIER
ALARM
LINK
5POWER SUPPLY 1
POWER SUPPLY 2
3 1
4 2SPA-4XT3/E3
TXRX
A/L0
C/A
TXRX
A/L1
C/A
TXRX
A/L2
C/A
TXRX
A/L3
STATUSC/A
2-3Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Identifying Slots and Subslots for SIPs and SPAs
Some commands allow you to display information about the SIP itself, such as show module, show sip-disk, show idprom module, show hw-module slot, and show diagbus. These commands require you to specify the chassis slot location where the SIP that you want information about is installed.
For example, to display status and information about the SIP installed in slot 6 as shown in Figure 2-1, enter the following command:
Router# show module 6
For more information about SIP commands, refer to the Cisco IOS Software Releases 12.2SR Command References and to the Cisco IOS Software Releases 12.2SX Command References.
Specifying the SIP or SSC Subslot Location for a SPA
SIP subslots begin their numbering with “0” and have a horizontal or vertical orientation depending on the orientation of the SIP in the router chassis slot, as shown in the “SIP, SSC, and SPA Product Overview” chapter of the Cisco 7600 Series Router SIP, SSC, and SPA Software Configuration Guide.
1 SIP subslot 0 4 SIP subslot 3
2 SIP subslot 1 5 Chassis slots 1–9 (numbered from right to left) (numbered from top to bottom)
3 SIP subslot 2
1389
80
FANSTATUS
INPUTOK
FANOK
OUTPUTFAIL
o
INPUTOK
FANOK
OUTPUTFAIL
o
1
2
3
4
5
6
7
8
9
STATUS
2
0
3
1
SPA INTERFACEPROCESSOR
7600-SIP-200
SPA-4XT3/E3
TX RX
A/L0
C/A
TX RX
A/L1
C/A
TX RX
A/L2
C/A
TX RX
A/L3
STATUSC/A
8 PORT GIGABIT ETHERNET
WS-X6408
1
LINK
STATUS 2 3 4 5 6 7 8
LINK
LINK
LINK
LINK
LINK
LINK
LINK
8 PORT GIGABIT ETHERNET
WS-X6408
1LIN
K
STATUS 2 3 4 5 6 7 8
LINK
LINK
LINK
LINK
LINK
LINK
LINK
8 PORT GIGABIT ETHERNET
WS-X6408
1
LINK
STATUS 2 3 4 5 6 7 8
LINK
LINK
LINK
LINK
LINK
LINK
LINK
24 PORT 100FX
WS-X6224
STATUS
24 PORT 100FX
WS-X6224
STATUS
24 PORT 100FX
WS-X6224
STATUS
1
LINK
2
LINK
3
LINK
4
LINK
5
LINK
6
LINK
7
LINK
8
LINK
9
LINK
10
LINK
11
LINK
12
LINK
13
LINK
14
LINK
15
LINK
16
LINK
17
LINK
18
LINK
19
LINK
20
LINK
21
LINK
22
LINK
23
LINK
24
LINK
1
LINK
2
LINK
3
LINK
4
LINK
5
LINK
6
LINK
7
LINK
8
LINK
9
LINK
10
LINK
11
LINK
12
LINK
13
LINK
14
LINK
15
LINK
16
LINK
17
LINK
18
LINK
19
LINK
20
LINK
21
LINK
22
LINK
23
LINK
24
LINK
1
LINK
2
LINK
3
LINK
4
LINK
5
LINK
6
LINK
7
LINK
8
LINK
9
LINK
10
LINK
11
LINK
12
LINK
13
LINK
14
LINK
15
LINK
16
LINK
17
LINK
18
LINK
19
LINK
20
LINK
21
LINK
22
LINK
23
LINK
24
LINK
SUPERVISOR2
WS-X6K-SUP2-2GE
STATUS
SYSTEM
CONSOLE
PWR M
GMT
RESET
CONSOLE
CONSOLEPORTMODE
PCMCIA EJECT
PORT 1 PORT 2
Switch Load 100%
1%
LINK
LINK
SUPERVISOR2
WS-X6K-SUP2-2GE
STATUS
SYSTEM
CONSOLE
PWR M
GMT
RESET
CONSOLE
CONSOLEPORTMODE
PCMCIA EJECT
PORT 1 PORT 2
Switch Load 100%
1%
LINK
LINK
13 4
5
2
2-4Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-200 Overview
Figure 2-1 shows an example of a Cisco 7600 SIP-200 installed with a vertical orientation on a Cisco 7609 router. The Cisco 7600 SIP-200 supports four subslots for the installation of SPAs. In this example, the subslot locations are vertically oriented as follows:
• SIP subslot 0—Top–right subslot
• SIP subslot 1—Bottom–right subslot
• SIP subslot 2—Top–left subslot
• SIP subslot 3—Bottom–left subslot
Figure 2-3 shows the faceplate for the Cisco 7600 SIP-200 in a horizontal orientation.
Figure 2-3 Cisco 7600 SIP-200 Faceplate
In this view, the subslot locations in a horizontal orientation are as follows:
• SIP subslot 0—Top–left subslot
• SIP subslot 1—Top–right subslot
• SIP subslot 2—Bottom–left subslot
• SIP subslot 3—Bottom–right subslot
The SIP subslot numbering is indicated by a small numeric label beside the subslot on the faceplate.
Just as with the SIPs, some commands allow you to display information about the SPA itself, such as show idprom module and show hw-module subslot. These commands require you to specify both the physical location of the SIP and SPA in the format, slot/subslot, where:
• slot—Specifies the chassis slot number in the Cisco 7600 series router where the SIP is installed.
• subslot—Specifies the secondary slot of the SIP where the SPA is installed.
For example, to display the operational status for the SPA installed in the first subslot of the SIP in chassis slot 6 shown in Figure 2-1, enter the following command:
Router# show hw-module subslot 6/0 oir
For more information about SIP commands, refer to the Cisco IOS Software Releases 12.2SR Command References and to the Cisco IOS Software Releases 12.2SX Command References.
Cisco 7600 SIP-200 OverviewThe following sections describe the Cisco 7600 SIP-200 (Cisco part number 7600-SIP-200):
• Cisco 7600 SIP-200 Processor, page 2-6
• Cisco 7600 SIP-200 LEDs, page 2-6
• Cisco 7600 SIP-200 Physical Specifications, page 2-6
• Cisco 7600 SIP-200 Memory Options, page 2-7
• Cisco 7600 SIP-200 Default DIP Switch Settings, page 2-8
STATUS
2
0
3
1
SPA INTERFACEPROCESSOR
7600-SIP-200
1168
49
2-5Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-200 Overview
Cisco 7600 SIP-200 ProcessorThe processor on a Cisco 7600 SIP-200 is described in Table 2-2.
Cisco 7600 SIP-200 LEDsThe Cisco 7600 SIP-200 has one LED, as shown in Figure 2-4.
Figure 2-4 Cisco 7600 SIP-200 Faceplate
The Cisco 7600 SIP-200 LED is described in Table 2-3.
Cisco 7600 SIP-200 Physical SpecificationsThe Cisco 7600 SIP-200 physical specifications are shown in Table 2-4.
Table 2-2 Cisco 7600 SIP-200 Processor
Type Speed Description
CPU 800 megahertz (MHz) internal operating frequency
Broadcom 1125 MIPS-based design
STATUS
2
0
3
1
SPA INTERFACEPROCESSOR
7600-SIP-200
1168
49
Table 2-3 Cisco 7600 SIP-200 LED
LED Label Color State Meaning
STATUS Red On The SIP has encountered an error.
Green On The SIP is online.
Yellow On The SIP is loading.
Off Off The SIP is powered off.
Table 2-4 Cisco 7600 SIP-200 Physical Specifications
Description Specifications
Physical dimensions The SIP occupies one module slot and can be operated in Cisco 7600 series routers.
Shipping weight 8 lb (3.64 kg)
Operating temperature 32 to 104°F (0 to 40°C)
Relative humidity 10 to 90 percent, noncondensing
Storage temperature –4 to 149°F (–20 to 65°C)
2-6Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-200 Overview
Cisco 7600 SIP-200 Memory OptionsThe following table lists the memory available for the Cisco 7600 SIP-200:
Note The SIP DIMMs must be a matched set. A warning message appears on the console if the DIMMs on the SIP are different sizes. If the sizes are not the same, the following message appears at bootup/OIR:
C7600_SIP200-3-MEM_MODULE_MISMATCH: Memory modules are not identical
Cisco 7600 SIP-200 Memory Installation and Removal
Figure 2-5 shows the location of the DIMMs on a Cisco 7600 SIP-200. Perform the following procedure to install and remove a DIMM:
To install a DIMM, slide the DIMM into the slot. The retaining clips secure the DIMM in place.
Step 1 To remove a DIMM, separate the two retaining clips.
Step 2 Pull the DIMM from the slot.
Figure 2-5 SIP DIMM Location
Table 2-5 SIP Memory Options
SIP Memory Options
Cisco 7600 SIP-200 512 MB and 1 GB (2 x 256-MB or 2 x 512-MB DIMMs)
1 DIMMs
STATUS
2
0
MODULARSERVICES CARD
7600-MSC-200
1223
90
1
2-7Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Cisco 7600 SIP-200 Default DIP Switch SettingsIf SW3 and SW10 switches are present on the board, make sure they are set to the default settings, as shown in Table 2-5. See Figure 2-6 for the location of the switches.
The switches are set to their defaults during manufacture. However, the switch settings may get inadvertently changed during handling.
Note If the switches are not set to their default settings, there may be momentary packet drops during OIR of the board.
Figure 2-6 Cisco 7600 SIP-200 DIP Switch Locations\
Cisco 7600 SIP-400 OverviewThe following sections describe the Cisco 7600 SIP-400 (Cisco part number 7600-SIP-400):
• Cisco 7600 SIP-400 Processor, page 2-9
• Cisco 7600 SIP-400 LEDs, page 2-9
• Cisco 7600 SIP-400 Physical Specifications, page 2-9
• Cisco 7600 SIP-400 Memory Removal and Installation, page 2-10
Table 2-1 Cisco 7600 SIP-200 Default DIP Settings
Switch Default Position
SW3 Up
SW10 Down
1 SW3 2 SW10
STATUS
2
0
MODULARSERVICES CARD
7600-MSC-200
1297
24
1
2
2-8Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Cisco 7600 SIP-400 ProcessorThe processor on a Cisco 7600 SIP-400 is described in Table 2-6.
Cisco 7600 SIP-400 LEDsThe Cisco 7600 SIP-400 has one LED, as shown in Figure 2-7.
Figure 2-7 Cisco 7600 SIP-400 Faceplate
The Cisco 7600 SIP-400 LED is described in Table 2-7.
Cisco 7600 SIP-400 Physical SpecificationsThe Cisco 7600 SIP-400 physical specifications are shown in Table 2-8.
Table 2-6 7600-SIP-400 Processor
Type Speed Description
CPU 400 megahertz (MHz) internal operating frequency
Broadcom 1125 MIPS-based design
STATUS
2
0
3
1
SPA INTERFACEPROCESSOR
7600-SIP-400
1013
13
Table 2-7 Cisco 7600 SIP-400 LED
LED Label Color State Meaning
STATUS Red On The SIP has encountered an error.
Green On The SIP is online.
Yellow On The SIP is loading.
Off Off The SIP is powered off.
Table 2-8 Cisco 7600 SIP-400 Physical Specifications
Description Specifications
Physical dimensions The SIP occupies one module slot and can be operated in Cisco 7600 series routers.
Shipping weight 8 lb (3.64 kg)
Operating temperature 32 to 104°F (0 to 40°C)
Relative humidity 10 to 90 percent, noncondensing
Storage temperature –4 to 149°F (–20 to 65°C)
2-9Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Cisco 7600 SIP-400 Memory Removal and Installation
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030.
Caution Only memory approved by Cisco is supported. Do not attempt to install other devices or DIMMs, which are not approved by Cisco in the DIMM sockets.
Caution DIMMs are ESD-sensitive components and can be damaged due to mishandling. Ensure that it is handled with care during installation and removal.
To remove a DIMM and install a new DIMM for the Cisco 7600 Series SPA Interface Processor-400 (SIP-400), follow these steps:
Step 1 Wear an ESD-preventative wrist strap and attach it to an unpainted part of the router surface.
Step 2 Locate the SPA jacket cover on the SIP. See Figure 2-8.
Figure 2-8 Identifying the SPA Jacket Cover
3915
76
1
2
2-10Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Step 3 Remove the front panel flexible PCB cable from the daughterboard. See Figure 2-9.
Figure 2-9 Removing the Front Panel Flex Cable
Label Component
1 SPA jacket cover
2 Daughterboard
39
16
17
2-11Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Step 4 Flip the 7600-SIP-400 assembly unit upside down to have the base plate side up, and then remove the 13 small screws from the base plate. See Figure 2-10.
Figure 2-10 Removing the SPA Jacket Cover from the Base Plate
39
15
77
2-12Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Step 5 Flip the 7600-SIP-400 assembly unit over to have the daughterboard on top.
Step 6 Slide the shared port adapter (SPA) jacket cover away from the daughterboard to leave a gap between the two, and then remove the SPA jacket cover. See Figure 2-11.
Figure 2-11 Sliding the SPA Jacket Cover
3915
78
2-13Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Step 7 Unscrew the 16 screws that secure the daughterboard to the motherboard. See Figure 2-12.
Figure 2-12 Removing Screws from the Daughterboard
3915
79
2-14Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Step 8 Lift the daughterboard to disconnect the interboard connector between the daughterboard and the motherboard. See Figure 2-13.
Figure 2-13 Removing the Daughterboard
3915
80
2-15Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Step 9 Locate the DIMM on the daughterboard. See Figure 2-14.
Figure 2-14 Locating the DIMM and Interboard Connectors on the Motherboard
Caution Handle the DIMM only along the edges. Do not touch the memory modules, pins, or traces (metal fingers along the connector edge), to avoid damage.
Step 10 Pull the retaining clips holding the DIMM away with your thumb. See A in Figure 2-15.
Step 11 When both ends of the DIMM are released from the retaining clips, grasp the ends of the DIMM with your thumb and forefinger, and pull it completely out of the socket. See Figure 2-16 and A in Figure 2-15. Then, in compliance with electronic waste laws, dispose the DIMM.
3915
81
2
1
3
Label Component
1 Interboard connectors on the daughterboard
2 Interboard connectors on the motherboard
3 DIMM
2-16Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Figure 2-15 Removal and Installation of DIMM
Lable Component
1 DIMM
2 Retaining clip
3915
82
A1
22
2
1 1
3
B
1
22
2
33
1
2-17Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Figure 2-16 Holding the DIMM
Caution It is normal to feel some resistance when installing a DIMM. Do not use excessive force or touch the surface components, to avoid damage
Step 12 Install the replacement DIMM by holding the component-side facing up with the connector edge (the metal fingers) away from you. Keep the sides of the DIMM between your thumb and index finger. See Figure 2-16 and B in Figure 2-15.
Step 13 Tilt the DIMM at a 30 degree angle to the socket, and then insert the connector edge of the DIMM into the socket. Verify that the notches on the DIMM are properly aligned with the ones on the connector before fully inserting the DIMM.
Step 14 Press down on the DIMM until the retaining clips lock the DIMM in place. See B in Figure 2-15.
Step 15 Check the two alignment notches, and ensure that the clips are visible. If necessary, remove and reseat the DIMM. See B in Figure 2-15.
3821
21
2-18Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
22
A
1
2
1
3
391546
B
1
2 2
2
3
1
Caution Improper alignment can permanently damage the interboard connectors between the daughterboard and motherboard. It is normal to feel some resistance when connecting the interboard connectors. Do not use excessive force to avoid damage.
Step 16 Press the daughterboard back on the motherboard to connect the interboard connectors between the daughterboard and the motherboard. See Figure 2-17.
Figure 2-17 Replacing the Daughterboard
3915
97
2-19Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Step 17 Insert and tighten the 16 screws that were removed in Step 7. See Figure 2-18.
Figure 2-18 Installing the Screws on the Daughterboard
3915
96
2-20Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Step 18 Replace the SPA jacket cover and slide it towards the daughterboard to remove any gap between the two. See Figure 2-19.
Figure 2-19 Sliding the SPA Jacket Cover
3915
95
2-21Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-400 Overview
Step 19 Turn the SIP assembly unit over.
Step 20 Insert and tighten the 13 small screws that were removed in Step 4.
Figure 2-20 Installing the SPA Jacket Cover to the Base Plate
3915
94
2-22Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 21 Reconnect the front panel flexible PCB cable to the daughterboard that was removed in Step 3. Ensure that actuator of the flexible PCB connector is in locked position.
Figure 2-21 Installing the Front Panel Flex Cable
Cisco 7600 SIP-600 OverviewThe following sections describe the Cisco 7600 SIP-600 (Cisco part number 7600-SIP-600):
• Cisco 7600 SIP-600 Processor, page 2-23
• Cisco 7600 SIP-600 LEDs, page 2-24
• Cisco 7600 SIP-600 Physical Specifications, page 2-24
• Cisco 7600 SIP-600 Memory Removal and Installation, page 2-25
Cisco 7600 SIP-600 ProcessorThe processor on a Cisco 7600 SIP-600 is described in Table 2-9.
3916
18
2-23Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Cisco 7600 SIP-600 LEDsThe Cisco 7600 SIP-600 has one LED, as shown in Figure 2-22.
Figure 2-22 Cisco 7600 SIP-600 Faceplate
The Cisco 7600 SIP-600 LED is described in Table 2-10.
Cisco 7600 SIP-600 Physical SpecificationsThe Cisco 7600 SIP-600 physical specifications are shown in Table 2-11.
Table 2-9 Cisco 7600 SIP-600 Processor
Type Speed Description
CPU 400 megahertz (MHz) internal operating frequency
Broadcom 1125 MIPS-based design
STATUS
2
0
3
1
SPA INTERFACEPROCESSOR
7600-SIP-600
1381
27
Table 2-10 Cisco 7600 SIP-600 LED
LED Label Color State Meaning
STATUS Red On The SIP has encountered an error.
Green On The SIP is online.
Yellow On The SIP is loading.
— Off The SIP is powered off.
Table 2-11 Cisco 7600 SIP-600 Physical Specifications
Description Specifications
Physical dimensions The SIP occupies one module slot and can be operated in Cisco 7600 series routers. The Cisco 7600-SIP-600 supports installation of only a single SPA in the first subslot.
Shipping weight 8 lb (3.64 kg)
Operating temperature 32 to 104°F (0 to 40°C)
Relative humidity 10 to 90 percent, noncondensing
Storage temperature –4 to 149°F (–20 to 65°C)
2-24Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Cisco 7600 SIP-600 Memory Removal and Installation
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030.
Caution Only memory approved by Cisco is supported. Do not attempt to install other devices or DIMMs, which are not approved by Cisco, in the DIMM sockets.
Caution DIMMs are ESD-sensitive components and can be damaged due to mishandling. Ensure that it is handled with care during installation and removal.
To remove a DIMM and install a new DIMM for the Cisco 7600 Series SPA Interface Processor-600 (SIP-600), follow these steps:
Step 1 Wear an ESD-preventative wrist strap and attach it to an unpainted part of the router surface.
Step 2 Locate the SPA jacket cover on the SIP. See Figure 2-23.
Figure 2-23 Identifying the SPA Jacket Cover
1
2
3915
39
2-25Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 3 Remove the front panel flexible PCB cable from the daughterboard. See Figure 2-24.
Figure 2-24 Removing the Front Panel Flex Cable
Label Component
1 SPA jacket cover
2 Daughterboard
3915
40
2-26Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 4 Flip the 7600-SIP-600 assembly unit upside down to have the base plate side up, and then remove the 13 small screws from the base plate. See Figure 2-25.
Figure 2-25 Removing the SPA Jacket Cover from the Base Plate
3915
41
2-27Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 5 Flip the 7600-SIP-600 assembly unit over to have the daughterboard on top.
Step 6 Slide the shared port adapter (SPA) jacket cover away from the daughterboard to leave a gap between the two, and then remove the SPA jacket cover. See Figure 2-26.
Figure 2-26 Sliding the SPA Jacket Cover
3915
42
2-28Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 7 Unscrew the 10 screws that secure the daughterboard to the motherboard. See Figure 2-27.
Figure 2-27 Removing Screws from the Daughterboard
3915
43
2-29Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 8 Lift the daughterboard to disconnect the interboard connector between the daughterboard and the motherboard. See Figure 2-28.
Figure 2-28 Removing the Daughterboard
391544
2-30Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 9 Locate the DIMM on the motherboard. See Figure 2-29.
Figure 2-29 Locating the DIMM and Interboard Connectors on the Motherboard
Caution Handle the DIMM only along the edges. Do not touch the memory modules, pins, or traces (metal fingers along the connector edge), to avoid damage.
Step 10 Pull the retaining clips holding the DIMM away with your thumb. See A in Figure 2-30.
Step 11 When both ends of the DIMM are released from the retaining clips, grasp the ends of the DIMM with your thumb and forefinger, and pull it completely out of the socket. See Figure 2-31 and A in Figure 2-30. Then, in compliance with electronic waste laws, dispose the DIMM.
12
3915
45Label Component
1 Interboard connectors
2 DIMM
2-31Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Figure 2-30 Removing and Installing the DIMM
Figure 2-31 Holding the DIMM
Lable Component
1 DIMM
2 Retaining clip
22
A
1
2
1
3
391546
B
1
2 2
2
3
1
3821
15
2-32Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Caution It is normal to feel some resistance when installing a DIMM. Do not use excessive force or touch the surface components, to avoid damage
Step 12 Install the replacement DIMM by holding the component-side facing up with the connector edge (the metal fingers) away from you. Keep the sides of the DIMM between your thumb and index finger. See Figure 2-31 and B in Figure 2-30.
Step 13 Tilt the DIMM at a 30 degree angle to the socket, and then insert the connector edge of the DIMM into the socket. Verify that the notches on the DIMM are properly aligned with the ones on the connector before fully inserting the DIMM.
Step 14 Press down on the DIMM until the retaining clips lock the DIMM in place. See B in Figure 2-30.
Step 15 Check the two alignment notches, and ensure that the clips are visible. If necessary, remove and reseat the DIMM. See B in Figure 2-30.
2-33Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Caution Improper alignment can permanently damage the interboard connectors between the daughterboard and motherboard. It is normal to feel some resistance when connecting the interboard connectors. Do not use excessive force to avoid damage.
Step 16 Press the daughterboard back on the motherboard to connect the interboard connectors between the daughterboard and the motherboard. See Figure 2-32.
Figure 2-32 Replacing the Daughterboard
3916
02
2-34Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 17 Insert and tighten the 10 screws that were removed in Step 7. See Figure 2-33.
Figure 2-33 Installing the Screws on the Daughterboard
3916
01
2-35Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 18 Replace the SPA jacket cover and slide it towards the daughterboard to remove any gap between the two. See Figure 2-34.
Figure 2-34 Sliding the SPA Jacket Cover
3916
00
2-36Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 19 Turn the SIP assembly unit over.
Step 20 Insert and tighten the 13 small screws that were removed in Step 4. See Figure 2-35.
Figure 2-35 Installing the Screws on the Base Plate
3915
99
2-37Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview
Step 21 Reconnect the front panel flexible PCB cable to the daughterboard that was removed in Step 3. See Figure 2-36. Ensure that actuator of the flexible PCB connector is in locked position.
Figure 2-36 Installing the Front Panel Flex Cable
3915
98
2-38Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SSC-400 Overview
Cisco 7600 SSC-400 OverviewThe following sections describe the SPA services carrier (Cisco part number 7600-SSC-400):
• Cisco 7600 SSC-400 Processor, page 2-39
• Cisco 7600 SSC-400 LED, page 2-39
• Cisco 7600 SSC-400 Physical Specifications, page 2-40
Cisco 7600 SSC-400 ProcessorThe processor on a Cisco 7600 SSC-400 is described in Table 2-12.
Cisco 7600 SSC-400 LEDThe Cisco 7600 SSC-400 has one LED, as shown in Figure 2-37.
Figure 2-37 Cisco 7600 SSC-400 Faceplate
The Cisco 7600 SSC-400 LED is described in Table 2-13.
Table 2-12 7600-SSC-400 Processor
Type Speed Description
CPU 400 megahertz (MHz) internal operating frequency
Broadcom 1125 MIPS-based design
STATUS
2
0
3
1
SERVICESSPA CARRIER
7600-SSC-400
1164
38
Table 2-13 Cisco 7600 SSC-400 LED
LED Label Color State Meaning
STATUS Red On The Cisco 7600 SSC-400 has encountered an error.
Green On The Cisco 7600 SSC-400 is online.
Yellow On The Cisco 7600 SSC-400 is loading.
Off Off The Cisco 7600 SSC-400 is powered off.
2-39Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15
Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SSC-400 Overview
Cisco 7600 SSC-400 Physical SpecificationsThe Cisco 7600 SSC-400 physical specifications are shown in Table 2-14.
Table 2-14 Cisco 7600 SSC-400 Physical Specifications
Description Specifications
Physical dimensions The Cisco 7600 SSC-400 occupies one module slot and can be operated in Cisco 7600 series routers.
Shipping weight 8 lb (3.64 kg)
Operating temperature 32 to 104°F (0 to 40°C)
Relative humidity 10 to 90 percent, noncondensing
Storage temperature –4 to 149°F (–20 to 65°C)
2-40Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-15