+ All Categories
Home > Documents > Owner‘s manual Ice Cube Machine · 3 Stand 01/20187 TM MODEL OVERVIEW / TECHNICAL DATA MODELL EB...

Owner‘s manual Ice Cube Machine · 3 Stand 01/20187 TM MODEL OVERVIEW / TECHNICAL DATA MODELL EB...

Date post: 08-Jun-2018
Category:
Upload: trinhquynh
View: 218 times
Download: 0 times
Share this document with a friend
16
Modell EB 26 / EB 40 Order no. 325-1005 / 325 - 1010 Owner‘s manual Ice Cube Machine English EB 26 EB 40
Transcript

Modell EB 26 / EB 40Order no. 325-1005 / 325 - 1010

Owner‘s manualIce Cube Machine

English

EB 26 EB 40

Stand 01/2018 TM

Dear customer,

thank you for choosing our ice cube maker. We hope you will enjoy our advanced product.

The ice cube makers of the „EB“ series have features that support you in your daily work routine and at the same time protect the environment.

The use of our new innovative technology guarantees a long service life and significantly reduces the noise level.

The hollow cones produced promise a great advantage, as these hollow ice cones can be used in mixers without overloading the knives. In addition, all ice cube makers have a water recycling system that saves up to 80% water compared to other appliances without a recycling system.

An insulated reservoir ensures that the hollow cones are retained for a long time. This reduces energy consumption. Any condensation that occurs is automatically removed.

Due to the compact design and the retractable removal flaps, the units can also be installed in a small space and the high-quality stainless steel housing enables easy cleaning.

In all ice cube makers we use the refrigerant R 600a or R 290, which makes them environmentally friendly and HFC-free.

The ice cube makers are used for commercial use in hotels, restaurants, canteens, bars, etc.

Saro does not warrant that the equipment will be used for any purpose other than that for which it is intended.

We hope you enjoy your new SARO ice cube maker!

1Stand 01/20187 TM

CONTENT

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Delivery Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Standards and directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Model overview / Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation, start-up and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Affiliation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Circuit diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Device parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Trouble shooting and solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Stand 01/2018 TM

INTRODUCTION

Before commissioning this device, read these operating instructions carefully and carefully and observe the information given therein.

This manual contains information on the structure, installation, operation, maintenance, cleaning and possible disposal of this unit.

This instruction manual is an integral part of the unit and should be kept in the vicinity of the unit at all times, accessible to all persons involved in the installation, operation, cleaning or maintenance of this unit.

If the device is passed on to third parties, these operating instructions must be included.

Illustrations in this manual may differ from the original article. We reserve the right to make technical changes to the device.

If these operating instructions are not observed, the safety of the device is no longer guaranteed.The manufacturer/dealer cannot be held responsible for damage caused by the manufacturer/dealer. Failure to observe these operating instructions will result.

DELIVERY PACKAGE• 1 Professional ice cube maker• 1 instruction manual• 1 Hose for fixed water connection (3/4 Zoll) • 1 Drain hose (1/2 Zoll)

STANDARDS AND DIRECTIVESThe device complies with current EU standards and directives.If necessary, we will send you the corresponding declaration of conformity.

2

Attention! This ice cube maker was developed and built for commercial use. It is only intended to produce the ice-cream body.

3Stand 01/20187 TM

MODEL OVERVIEW / TECHNICAL DATA

MODELL EB 26 EB 40

Order No. 325-1005 325-1010Dimension B 420 x T 528 x H 655 B 496 x T 610 x H 792Connection (V / Hz / kW) 230 / 1 / 0,16 220 / 1 / 0,26Weight 32 kg 45 kgRefrigerant R 600a R 290Air cooling yes yesIce production 26 kg / 24 h 40 - 50 kg / 24 hReservoir 6 kg 10 kgDrain hose 1/2 Zoll 1/2 ZollFixed water connection 3/4 Zoll 3/4 ZollIce cone size (ø ; mm) ca. ø 28 x H 40 mm ca. ø 28 x H 40 mmIce cone sizes adjustable no noNoise emission ca. 55 db ca. 55 dbCirculation system yes yesBody stainless steel stainless steel4 height-adjustable feet yes yes

EXPLANATION OF SYMBOLS

WARNING!This symbol indicates dangers that may cause injury.It is imperative that you strictly adhere to the information on occupational safety and be particularly careful in these cases.

WARNING: DANGER FROM ELECTRICAL CURRENT!This symbol draws attention to dangerous situations caused by electrical current. Failure to observe the safety instructions may result in injury or death!

WARNING: FIRE HAZARDOUS MATERIALS - DANGER OF BURNING!This symbol indicates that there are dangers due to flammable substances for the life and health of persons. Risk of burns in case of Disregard!!

IMPORTANT NOTICEThe safety instructions in this instruction manual are marked with appropriate symbols. These indicate possible dangers. The accompanying information must be read and observed!

Stand 01/2018 TM4

SAFETY NOTICES

• Before the first start-up, read these operating instructions carefully and observe the information given therein.

• Incorrect operation and improper handling can lead to malfunctions on the device and injury to the user.

• Observe the accident prevention regulations applicable to the area of application and the general safety regulations.

• Ensure a safe stand on a dry, non-slip surface that is adequate to the weight of the equipment. If the ground is not stable enough, the unit may tip over and cause injury.

• Do not place the device on a hot surface and keep away from any heat source and direct sunlight.• The ice cube maker may only be transported upright.• Do not tilt the unit by more than 45 degrees.• Do not move the device during use.• Before moving the unit, unplug the power cord.• Make sure that the device does not tip when moving. This could lead to injuries• Keep packaging materials (plastic film) out of the reach of children.• The unit may only be connected to a properly installed power outlet.• Do not plug any other device into the same outlet. Make sure that the wall socket is plugged in.• is generally accessible so that the device can be disconnected from the power supply in an

emergency.• Do not use ice cubes produced in the first 2 hours.• After longer transport, the unit should not be put back into operation until after 24 hours.• Do not let the power cord hang over sharp edges and keep it away from hot spots, objects and open

flames.• When unplugging the power cord, always pull the plug housing and never the cable. Turn off the

device before starting.• Make sure that unintentional pulling on the cable or tripping over it is not possible.• Do not damage or modify the power cord, pull, strain, bend or squeeze it, twist or roll it up.• Do not clean the unit with an open water jet.• The unit must not be immersed in water or other liquids or wetted with liquids.• Do not place heavy objects or objects filled with liquids on the unit. Things could fall down and cause

injury. Liquids could be spilled, in the inside of the device and transmit electricity.• Only use the original parts provided for this purpose when operating the unit.• Never touch the device, cable or plug with wet hands.

5Stand 01/20187 TM

SAFETY NOTICES

• No operation of the equipment by children or persons with impaired physical, sensory or mental abilities; or lack of experience and/or knowledge. These persons are not able to recognize the dangers of using electrical appliances and/or devices that generate heat and may cause accidents, fire or damage to property.

• Disconnect the plug from the power outlet before cleaning, or disconnect the unit from the power supply; this also applies if the unit is not used for a longer period of time.

• In the event of a fault or malfunction, turn off the unit and unplug the power cord. Notify your dealer. He will carry out the repair with original spare parts.

• Refrigeration maintenance may only be carried out by qualified personnel. • Never hang yourself from the door of the device and never climb onto it. The unit may tip over and be

damaged or cause injury.• The amount of refrigerant contained in this unit is given in grams; it is also indicated on the type plate

of the unit.• After a possible power failure or a short disconnection, switch off the device for a short time, wait 5

minutes, plug the plug in again and start the device.• A damaged device must not be used!

Do not use any corrosive or abrasive cleaning agents! Do not use alcohol or alkaline detergents, thinners or benzene. This could damage the plastic parts or painted surfaces!Never use hot water to clean the unit!

After delivery or transport of the device, do not connect it until the device has been idle for at least 24 hours. This is absolutely necessary so that the coolant can collect in the compressor.

After a power failure or if the device has been disconnected from the power supply, wait at least 5 minutes before reconnecting and starting up the device!If the unit is restarted immediately after it has been switched off, the fuse may trip and interrupt the current flow. In addition, the compressor may be overloaded and damaged.

6Stand 01/2018 TM

GENERAL INFORMATION

• Before the first start-up, read these operating instructions carefully and observe the information given therein.

• Keep these operating instructions within easy reach, near the device.• The manufacturer/dealer cannot be held responsible for damage caused by non-observance of these

operating instructions.• If these operating instructions are not observed, the safety of the device is no longer guaranteed.

If the device is passed on to third parties, these operating instructions must be supplied with the device.

• This equipment must not be operated by children or persons with reduced physical, sensory or mental abilities, as they cannot recognize the dangers of using electrical appliances and/or refrigerators and as accidents, fires, explosions or damage to property may occur.

• Do not use the device outdoors in rain or in wet rooms.• After unpacking the device, make sure that everything is in perfect condition. If you discover any

damage, do not connect the device but contact your dealer.• Check that all components listed in the scope of delivery are present. If this is not the case, contact

your dealer.• Keep the unit‘s packaging. The device can only be transported safely in its original packaging.• Please note that all components of the packaging (plastic bags, cardboard, polystyrene parts, etc.)

may endanger children and must therefore not be stored near them.• If it is not possible to store the packaging, separate the various packaging materials and return them

to the nearest collection point for proper disposal.• Place the unit in a dry and adequately ventilated place.• Ensure a distance of at least 15 cm between the back of the ice cube maker and the wall. Otherwise,

the desired cooling capacity can no longer be guaranteed.• Do not place the unit near heat sources such as heating, stove, oven or open fire or in direct sunlight

as the desired cooling capacity can no longer be guaranteed.• The ventilation slots must always be kept clear and must not be covered or closed.• Before connecting the device to the power supply and putting it into operation, clean the device

thoroughly.• Do not drill or pierce holes in the inside or outside of the unit. The cooling circuit could be damaged.• The ice cube container is foamed in and thus well insulated. This reduces melting of the ice cubes.• The device is neither suitable nor intended for the storage of medicines or highly inflammable,

flammable or explosive substances.• Subject to technical modifications and errors excepted.

7Stand 01/20187 TM

INSTALLATION, START-UP AND OPERATION

• Unpack the package and take out the attached documents and spare parts such as the water inlet and outlet tubes, ice shovel etc.

• The ice cube machine should be positioned in a well ventilated area on a horizontal and stable ground.

• Make sure that the appliance is positioned not near to gas or electricity ovens or other sources of warmth and it must not come into contact with splash-water.

• Always leave at least 150 mm space on each side, so that the air can circulate well. Do not block the ventilation slots.

• Please adjust the feet, so that the ice cube machine stands absolutely level.• It has to be a downward gradient from the appliance to the discharge, because the ice cube machine

has no sewage pump. Therefore the drain hose should run below the appliance-lower-edge, so that the water can run out without any problem.

• Connect one end of the flexible plastic tube (included in the supply) with the water drain on the back side of the machine. The other tube end should be put into a tank (not included) for surplus water or into sewer.

• Connect one end of the inlet hose with the tap and the other end with the machine. In any case use at both connections the attached seals.

• Put the plug into a grounded plug socket and switch on the machine with the switch. In the first 3 minutes an automatic test run is done. Afterwards the machine starts the actual cool and production procedure. All production steps (water supply, ice preparing, ice cube production and keeping ice available) are continuously tested. If the ice storage container is full, the control lamp “ICE FULL” lights up and the ice cube production will be stopped automatically.

8Stand 01/2018 TM

• Before connecting the device to the mains, check that the type of current and the mains voltage comply with the information on the nameplate of the device.

• Make sure that the power cord is free of damage, a damaged cord must be replaced by a qualified professional.

• EA damaged device must not be used! In this case, disconnect the device from the power supply and contact your dealer

• Do not use adapters or extension cables• The device is under power as long as it is connected to the mains.• The unit does not have a power switch. Before the unit can be cleaned, the mains plug must first be

disconnected!• The device is intended for indoor use. Use outdoors, in rain, can lead to short circuits, leakage

current or electric shocks.• If the unit has become wet, unplug it from the mains immediately and have it checked by a

specialist before the next start-up. Danger of electric shock!• Never attempt to open or repair the device yourself. Danger of electric shock!

WARNING: DANGER FROM ELECTRICAL CURRENT!

WARNING: DANGER OF INJURY!

• Never try to place your fingers, chopsticks, screwdrivers or other thin objects between the bars of the cold air blower. Behind the protective grille, a fan rotates at high speed. There is a risk of injury, electric shock and damage to or malfunction of the unit.

WARNING: INJURY DANGER!

• Packaging materials such as foils, polystyrene or small parts of the transport safety device can be dangerous for children! There is a risk of injury or suffocation!

• Keep packaging material away from children at all times.

WARNING

9Stand 01/20187 TM

UNPACKINGMake sure that the packaging is undamaged. The device as well as the accessories are protected and / or fixed for transport. After opening the packaging, remove the packaging material and any transport securing devices in the form of adhesive tapes or cable ties.

Then check that the delivery is complete and make sure that neither the unit nor the accessories are damaged.

Keep the unit‘s packaging. The device can only be transported safely in its original packaging. If it is not possible to store the packaging, separate the various packaging materials and return them to the nearest collection point for proper disposal.

STRUCTUREPlace the unit in a dry and adequately ventilated room. Ensure that you stand securely on a dry and non-slip surface.

Place the unit with the rear side at least 10 cm away from the wall to ensure sufficient air circulation at all times. There should be at least 30 cm of space above the unit; 2 cm to the sides.

Performance and power consumption may be affected by ambient temperature or direct sunlight. Do not expose the unit to direct sunlight and do not place it near a stove, radiator or other heat source.

Ensure that the mains plug is always freely accessible and can be disconnected from the mains without any problems.

Set up the shelves of the appliance so that the distances correspond to the height of your goods.

Although the device has been cleaned from the inside before it was shipped, it is still necessary to clean the interior before filling it with merchandise.

Please wait 24 hours before switching on the device. During this time, we recommend that you leave the door open to remove any residual odours.

AFFILIATIONConnect the unit only to a grounding socket outlet with an earthing and a 230 volt connection.

Before connecting the device, make sure that the voltage and frequency of the power supply correspond to the information on the nameplate! Other voltages can lead to overheating of the device!

10Stand 01/2018 TM

CIRCUIT DIAGRAMS

MODEL EB 26

MODEL EB 40

11Stand 01/20187 TM

DEVICE PARTS

Ventilation slots at the front or on the side due to design.

1 Power Switch ON/OFF2 Display panel3 Front panel4 Door5 Ice bouncing shelf6 Ice storage container7 Ice lever sensor8 Power cord9 Water inlet valve10 Drainage tube11 Bottom foot

12Stand 01/2018 TM

• The unit must be disconnected from the power supply before cleaning!• Never use water directly or a water jet to clean the unit!• Never immerse the device, cable or plug in water!

WARNING: DANGER FROM ELECTRICAL CURRENT!

CLEANINGTo avoid the risk of electric shock or injury from the rotating fan, disconnect the unit from the power supply before cleaning. Do not start cleaning before the fan has come to a standstill!

• Clean the exterior surfaces with a damp, warm rag and a commercial cleaning agent. Do not use aggressive detergents and under no circumstances steel wool or abrasive sponges. The appliance may not be hosed down with water.

• Clean the ice storage container with a clean rag. Before take out the ice cubes.• Clean also from time to time the ventilation slots, because dust and dirt can block the slots. Remove

for this the plastic cover from the left side of the appliance by loosening the two screws. With a soft brush or hand brush and a vacuum cleaner make everything clean there. On the right side of the appliance it is sufficient to wipe off the plastic cover.

• Check the connection points for the water inlet and outlet of the unit regularly.• the ice cube maker is to be taken out of operation for a longer period of time, then

• turn it off • remove the plug from the socket • close the water supply • clean the inside and outside of the unit.

• It is advisable to pour a descaler into the drains from time to time and let it work for about 20 minutes. After this time, open the rear drain screws to drain the water/lime mixture. Then rinse the drains with clear water and screw them back on again. For health reasons, do not use ice cubes produced in the first 4 to 5 cycles after decalcification.

• We recommend that you have the ice cube maker completely disinfected by your specialist dealer once a year or after every longer shutdown of the unit. The works include: Cleaning the condenser, cleaning the filter on the magnetic valve of the water supply and cleaning the ice tank, the water pan and the evaporator.

13Stand 01/20187 TM

DISPOSAL

Once the appliance has been used up, please dispose of it properly at a collection point for electrical appliances. Electrical appliances do not belong in household waste.

Your responsible administration will inform you about the addresses and opening hours of collection points. This is the only way to ensure that old appliances are properly disposed of and recycled. Thank you very much!

TROUBLE SHOOTING AND SOLUTIONS

Errors Possible causes SolutionsThe appliance does not work.

Problems with the main electricity connection.

Ambient temperature is under 10°C.

Switch off and after 5 minutes restart.

Restart, if the ambient temperature is higher.

Warning lamp for to less water lights up.

Water intake disturbed

Valve is damaged.

Water pressure is too low.

Check the water intake

Check valve, if necessary, let it exchange.

The water pressure has to be at least 1 kg/cm2.

The condenser does not work.

Not enough water.

Ice collector container is full.

Check the water supply.

Empty the container.The condenser works, but no ice cubesare produced.

Leak in the cooling system.

Condenser dusty.

Kühlsystem vom Fachmann überprüfen lassen.

Kondensator staubfrei machen, Lüftungsschlitze reinigen

The ice cubes do not fall at all or only partially into the container.

Ambient temperature or water temperature are to low.

Valve is damaged.

Ambient temperature has to be at least 10°C and water temperature at least 7°C.

Exchange the valve.The ice cubes always stick together.

Storage tank is not sufficiently cooled.

Often emptying. Do not leave overnight in the storage tank. Control temperature.

14Stand 01/2018 TM

Made in P. R. C. forSARO Gastro-Products GmbHSandbahn 6, 46446 Emmerich am Rhein, GermanyTel. +49(0)2822 9258-0Fax +49(0)2822 18192E-Mail [email protected] / www.saro.de


Recommended