+ All Categories
Home > Documents > Oxygen Generator Systems - p-mgs.com · • Atlas Copco’s FX refrigerated dryer module • Atlas...

Oxygen Generator Systems - p-mgs.com · • Atlas Copco’s FX refrigerated dryer module • Atlas...

Date post: 06-Sep-2018
Category:
Upload: trinhtram
View: 217 times
Download: 0 times
Share this document with a friend
6
Pneumatech Medical Gas Solutions Email: [email protected] www.p-mgs.com The right is reserved to change this technical specification without prior notice Technical Datasheet 8102341150 Ed1 Page 1 Description The Pneumatech MGS modular Oxyplant system shall provide medical quality oxygen into the hospital pipeline system, deliv- ered at a pressure of 400 kPa (4 bar) gauge. The system shall use Atlas Copco compressors, dryer and filters, galvanised steel air receiver, PSA oxygen generator and steel oxygen receiver. The generator shall include a graphic LCD con- troller and oxygen sensor/analyser. Operation All components shall be self-controlled, no central controller is required. The compressor shall run to maintain pressure in the air receiver with a typical set pressure of 700 kPa (7 bar) gauge. The generator shall be run in a way to maintain pressure in the oxygen receiver at 400 kPa (4 bar) gauge, or up to a maximum pressure of 500 kPa (5 bar) gauge with an oxygen purity of 93%. The controller shall provide functionality to easily adjust the oxy- gen purity level up to 95%. In cases using dual independent production lines (according to ISO 10083) the system will work with the following logic: One generation line shall be determined as duty and the other shall in turn be set up as a back-up. It is recommended to switch between the lines once a week to ensure each generator is run. The system shall be pressure controlled. Each line has a differ- ent set pressure. The duty line has a start pressure of 430 kPa (4.3 bar) gauge and the reserve line at a fixed pressure of 400 kPa (4 bar) gauge. If the duty line is shut-down or fails the main line pressure will fall. When the reserve set pressure is reached (400 kPa, 4 bar) the reserve line will come on-line to maintain working line pressure. Pressure shall be measured in the oxygen buffer tank. When the pressure depletes it reaches the start set point and the genera- tor starts producing oxygen. When the pressure stop set-point is reached the generator shall go in stand-by mode. The oxygen generator shall automatically stop if the oxygen level falls below the set purity level (e.g. >92% as standard). In this case the reserve line will come on-line due to the pressure falling to 400 kPa (4 bar) gauge. The compressors shall run on their own pressure band and shall operate independently to the oxygen generators. As soon as the pressure in the tank reaches it’s set point (e.g. 700 kPa, 7 bar) the compressor shall go into unload/stop mode. In the case of generator failure a general alarm fault shall be trig- gered at 91% (adjustable). If the oxygen quality falls lower than 90% the generator shall stop and the reserve generator will start production of oxygen due to depletion of line pressure to 400 kPa (4 bar) gauge. Oxygen Generator Systems Oxygen Generator The oxyplant generator shall incorporate pressure swing absorp- tion (PSA) technology and supplied as a plug and play compo- nent for simple installation on site, including oxygen monitoring, service indications and relevant alarms. Non return valves shall be included to avoid back flow from the outlet of the generator. The vessels shall include chemically produced zeolite to adsorb specific types of molecules, such as water vapour or nitrogen. The oxyplant generator shall include an oxygen sensor and analyser for continuous, online measurement of oxygen purity and shall be provided with a calibration report delivered with every unit. The sensor shall be insulated by solenoid valves during standstill to provide longer sensor lifetime. An inlet pres- sure regulator shall be included to reduce the inlet pressure to a maximum working pressure of 650 kPa (6.5 bar ) gauge. The oxygen purity produced shall be between 90-95% with a compressed air inlet quality in accordance with ISO 8573-1 clause 1-4-1 and an air outlet quality in accordance with ISO 8573-1 clause 1-2-1. Control System The oxyplant T4 control system shall provide an intelligent human machine interface including a real-time clock for recording op- erational parameters in the event log. The central control system shall include a BMS connection for a general fault condition.
Transcript
Page 1: Oxygen Generator Systems - p-mgs.com · • Atlas Copco’s FX refrigerated dryer module • Atlas Copco DD+ and PD+ high efficiency filters • Accessories Options • Advanced T5

Pneumatech Medical Gas Solutions • Email: [email protected] • www.p-mgs.com• The right is reserved to change this technical specification without prior notice

Technical Datasheet81

0234

1150

Ed1

Pag

e 1

DescriptionThe Pneumatech MGS modular Oxyplant system shall provide medical quality oxygen into the hospital pipeline system, deliv-ered at a pressure of 400 kPa (4 bar) gauge.

The system shall use Atlas Copco compressors, dryer and filters, galvanised steel air receiver, PSA oxygen generator and steel oxygen receiver. The generator shall include a graphic LCD con-troller and oxygen sensor/analyser.

OperationAll components shall be self-controlled, no central controller is required. The compressor shall run to maintain pressure in the air receiver with a typical set pressure of 700 kPa (7 bar) gauge. The generator shall be run in a way to maintain pressure in the oxygen receiver at 400 kPa (4 bar) gauge, or up to a maximum pressure of 500 kPa (5 bar) gauge with an oxygen purity of 93%. The controller shall provide functionality to easily adjust the oxy-gen purity level up to 95%.

In cases using dual independent production lines (according to ISO 10083) the system will work with the following logic:

One generation line shall be determined as duty and the other shall in turn be set up as a back-up. It is recommended to switch between the lines once a week to ensure each generator is run. The system shall be pressure controlled. Each line has a differ-ent set pressure. The duty line has a start pressure of 430 kPa (4.3 bar) gauge and the reserve line at a fixed pressure of 400 kPa (4 bar) gauge. If the duty line is shut-down or fails the main line pressure will fall. When the reserve set pressure is reached (400 kPa, 4 bar) the reserve line will come on-line to maintain working line pressure.

Pressure shall be measured in the oxygen buffer tank. When the pressure depletes it reaches the start set point and the genera-tor starts producing oxygen. When the pressure stop set-point is reached the generator shall go in stand-by mode.

The oxygen generator shall automatically stop if the oxygen level falls below the set purity level (e.g. >92% as standard). In this case the reserve line will come on-line due to the pressure falling to 400 kPa (4 bar) gauge.

The compressors shall run on their own pressure band and shall operate independently to the oxygen generators. As soon as the pressure in the tank reaches it’s set point (e.g. 700 kPa, 7 bar) the compressor shall go into unload/stop mode.

In the case of generator failure a general alarm fault shall be trig-gered at 91% (adjustable). If the oxygen quality falls lower than 90% the generator shall stop and the reserve generator will start production of oxygen due to depletion of line pressure to 400 kPa (4 bar) gauge.

Oxygen Generator Systems

Oxygen GeneratorThe oxyplant generator shall incorporate pressure swing absorp-tion (PSA) technology and supplied as a plug and play compo-nent for simple installation on site, including oxygen monitoring, service indications and relevant alarms.

Non return valves shall be included to avoid back flow from the outlet of the generator. The vessels shall include chemically produced zeolite to adsorb specific types of molecules, such as water vapour or nitrogen.

The oxyplant generator shall include an oxygen sensor and analyser for continuous, online measurement of oxygen purity and shall be provided with a calibration report delivered with every unit. The sensor shall be insulated by solenoid valves during standstill to provide longer sensor lifetime. An inlet pres-sure regulator shall be included to reduce the inlet pressure to a maximum working pressure of 650 kPa (6.5 bar ) gauge.

The oxygen purity produced shall be between 90-95% with a compressed air inlet quality in accordance with ISO 8573-1 clause 1-4-1 and an air outlet quality in accordance with ISO 8573-1 clause 1-2-1.

Control SystemThe oxyplant T4 control system shall provide an intelligent human machine interface including a real-time clock for recording op-erational parameters in the event log. The central control system shall include a BMS connection for a general fault condition.

Page 2: Oxygen Generator Systems - p-mgs.com · • Atlas Copco’s FX refrigerated dryer module • Atlas Copco DD+ and PD+ high efficiency filters • Accessories Options • Advanced T5

Pneumatech Medical Gas Solutions • Email: [email protected] • www.p-mgs.com• The right is reserved to change this technical specification without prior notice

Technical Datasheet81

0234

1150

Ed1

Pag

e 2

Specifications• Supply voltage: 115-230V 50/60Hz (oxygen generator)• Power consumption: 200W max (oxygen generator)• CSA/UL approval available• Protection degree: IP54 (Nema 3S)• Operation at a maximum ambient temperature of 45°C. • Compressor 750 kPa (7.5 bar) gauge including EFF1 (CE MEP) rated TEFC, IP55 class F electric motors. Incorporating maintenance-free greased for life bearings. • Dryer 3°C PDP at 45°C• Air receivers DIRECTIVE 97/23/EC, supplied with relevant test certificates. • Oxygen vessel of steel construction and approved according to Fluid Group 1• PSA oxygen modules are able to produce oxygen compliant with the United States Pharmacopeia (USP) monograph for Oxygen 93 or the European Pharmacopeia (EurPh) mono graph for Oxygen 93. Both standards were created expressly to permit the use of PSA produced oxygen.

ClassificationOxyplant system is designed to ISO10083 standards and air quality to the European Pharmacopoeia monograph.

Features• Pre-piped, factory tested and certified• 91%, 93% or 95% oxygen purity• Zeolite providing infinite lifetime (if the dryers and filters are properly serviced) • Valves degreased for oxygen use are provided with an oxygen certificate, delivered with every unit• Pressure controlled – no central controller for simple operation• Silencer on exhaust to reduce noise levels• Touch screen controller on generator with 4” high-definition display• Zirconia oxygen sensor included on generator for long life and low maintenance• Atlas Copco’s premium GA oil flooded rotary screw compressor• Atlas Copco’s FX refrigerated dryer module• Atlas Copco DD+ and PD+ high efficiency filters• Accessories

Options• Advanced T5 controller including E-mail and SMS event notification for additional convenience. Graphical log for analogue values and user friendly touch screen 6” high-definition colour display

• High pressure booster System using oil free, high pressure pistons compressors shall be provided suitable for the on site filling of 15,000 kPa (150 bar) gauge or 20,000 kPa (200 bar) gauge oxygen cylinders. Compressors shall operate on an inlet pressure auto-cycling system (auto start/stop).

• Filling Ramp for on site cylinder filling consisting of a high pressure bar with individual isolation valves at each cylinder connection. The cylinders shall be protected from over pressurising by a safety pressure relief valve and shall include a pressure gauge. The filling ramp shall be tested up to 30,000 kPa (300 bar) gauge and shall be supplied complete with test certificate (cylinders are NOT included).

• Purge Control. An additional purge line to ensure that only the appropriate level of oxygen quality is supplied to the hospital distribution pipeline.

• Dew Point and Flow Monitoring. The dryer shall be able to incorporate a dew point sensor with an accuracy of ±10C in the range -20 to -800C atmospheric dew point and 4-20mA analogue output. The PDP sensor shall ensure the air to the generator inlet is suitable in order to safeguard the generator from high moisture content.

Page 3: Oxygen Generator Systems - p-mgs.com · • Atlas Copco’s FX refrigerated dryer module • Atlas Copco DD+ and PD+ high efficiency filters • Accessories Options • Advanced T5

Pneumatech Medical Gas Solutions • Email: [email protected] • www.p-mgs.com• The right is reserved to change this technical specification without prior notice

Technical Datasheet81

0234

1150

Ed1

Pag

e 3

Typical Layout - Schematic

BA

LL

V

AL

VE

BA

LL

VA

LV

E

AIR TANK 1

PR

ES

SU

RE

R

EG

UL

AT

OR Du

st

FIL

TE

R

WA

TE

R D

RA

IN

BA

LL

VA

LV

E

PR

ES

SU

RE

S

AF

ET

Y V

AL

VE

OX

YG

EN

GE

NE

RA

TO

R

BA

LL

VA

LV

E

PR

ES

SU

RE

S

AF

ET

Y V

AL

VE

BA

LL

VA

LV

EN

ON

-RE

TU

RN

V

AL

VE

BA

LL

V

AL

VE

BA

LL

VA

LV

E

AIR TANK 2

PR

ES

SU

RE

R

EG

UL

AT

OR D

ust

FIL

TE

R

WA

TE

R D

RA

IN

BA

LL

VA

LV

E

PR

ES

SU

RE

S

AF

ET

Y V

AL

VE

BA

LL

VA

LV

E

PR

ES

SU

RE

S

AF

ET

Y V

AL

VE

BA

LL

VA

LV

EN

ON

-RE

TU

RN

V

AL

VE

Fill

ing

ra

mp

INL

ET

-

DD

FIL

TE

R

INL

ET

-

PD

FIL

TE

RQ

D

AC

10

1

SR

10

1S

R1

02

SR

10

3

AD

10

1

BA

10

1

TK

10

1

BA

10

3

BA

10

2

SA

10

1

OG

10

1

BA

10

4

TK

10

2

SA

10

2

BA

10

5

O

XY

GE

N

BU

FF

ER

TA

NK

RV

10

1

SR

10

4N

R1

01

SR

20

4N

R2

01

RV

20

1

TK

20

2

BA

20

5

O

XY

GE

N

BU

FF

ER

TA

NK

BA

20

4

BA

20

3

BA

20

2

BA

20

1TK

20

1

SA

20

1S

A2

02

FR

10

1

B0

30

1

HIG

H

PR

ES

SU

RE

No

t in

clu

de

d in

sco

pe

of su

pp

ly

A/A

HE

AT

EX

CH

AN

GE

R

WA

TE

R

SE

PE

RA

TO

R

REFRIGERANT

SEPERATOR

R/A

HE

AT

EX

CH

AN

GE

R

RE

FR

IGE

RA

NT

CO

ND

EN

SO

R

RE

FR

IGE

RA

NT

CO

MP

RE

SS

OR

WA

TE

R

DR

AIN

FX

DR

YE

R

G

A

CO

MP

RE

SS

OR

WD

10

1

WD

20

1

INL

ET

-

DD

FIL

TE

R

INL

ET

-

PD

FIL

TE

R

SR

20

1S

R2

02

SR

20

3

AD

20

1

A/A

HE

AT

EX

CH

AN

GE

R

WA

TE

R

SE

PE

RA

TO

R

REFRIGERANT

SEPERATOR

R/A

HE

AT

EX

CH

AN

GE

R

RE

FR

IGE

RA

NT

CO

ND

EN

SO

R

RE

FR

IGE

RA

NT

CO

MP

RE

SS

OR

WA

TE

R

DR

AIN

FX

DR

YE

R

CO

MP

RE

SS

OR

INL

ET

FIL

TE

R

AIR

IN

TA

KE

TE

MP

ER

AT

UR

ET

RA

NS

DU

CE

R

AF

TE

R

CO

OL

ER

P

TE

MP

ER

AT

UR

E

TR

AN

SD

UC

ER

PR

ES

SU

RE

TR

AN

SD

UC

ER

NO

N-R

ET

UR

N

VA

LV

E

PR

ES

SU

RE

S

AF

ET

Y V

AL

VE

AU

TO

MA

TIC

D

RA

IN

BA

LL

VA

LV

ES

FL

EX

IBL

E

CO

NN

EC

TIO

N

TO

WE

RT

OW

ER

A

B

OX

YG

EN

GE

NE

RA

TO

R

OG

20

1

TO

WE

RT

OW

ER

A

B

AC

20

1

CO

MP

RE

SS

OR

INL

ET

FIL

TE

R

AIR

IN

TA

KE

TE

MP

ER

AT

UR

ET

RA

NS

DU

CE

R

AF

TE

R

CO

OL

ER

P

TE

MP

ER

AT

UR

E

TR

AN

SD

UC

ER

PR

ES

SU

RE

TR

AN

SD

UC

ER

NO

N-R

ET

UR

N

VA

LV

E

PR

ES

SU

RE

S

AF

ET

Y V

AL

VE

AU

TO

MA

TIC

D

RA

IN

BA

LL

VA

LV

ES

FL

EX

IBL

E

CO

NN

EC

TIO

N

G

A

CO

MP

RE

SS

OR

BA

LL

VA

LV

E

BA

LL

VA

LV

E

AIR

IN

LE

T

OX

YG

EN

OU

TL

ET

AIR

IN

LE

T

OX

YG

EN

OU

TL

ET

QD

(*)

Not applic

able

when o

nly

one o

xygen g

enera

tor

is insta

lled

BA106

BA

107

BA

207

BA206

Manifold

(*

)

BA310

T

O H

OS

PIT

AL

F

EE

D

NO

N-R

ET

UR

N

VA

LV

E (

*)

GA

10

1G

A1

02

GA

20

2G

A2

01

1 2

No

te:

Oxygen g

enera

tor

options c

an b

e insta

lled

See d

edic

ate

d flo

w d

iagra

m o

f genera

tor

Not all

deta

ils for

main

com

ponents

( c

om

pre

ssor,

genera

tor,

dry

er

)show

n. S

ee d

eta

ils for

indiv

idual com

ponents

*

Optional equip

ment

RV

30

1

AIR TANK 3

TK

30

1

BA

LL

V

AL

VE

BA

30

1

p

p

Pu

rge

fu

nctio

n(

op

tio

n )

p

p

Pu

rge

fu

nctio

n(

op

tio

n )

Page 4: Oxygen Generator Systems - p-mgs.com · • Atlas Copco’s FX refrigerated dryer module • Atlas Copco DD+ and PD+ high efficiency filters • Accessories Options • Advanced T5

Pneumatech Medical Gas Solutions • Email: [email protected] • www.p-mgs.com• The right is reserved to change this technical specification without prior notice

Technical Datasheet81

0234

1150

Ed1

Pag

e 4

Typical Simplex Installation Typical Duplex Installation

1 Compressor 6 Purity measurement line

2 Refrigerant dryer 7 Ball valve

3 Filters DD-PD-QD 8 Oxygen tank

4 Air receiver 9 Pressure regulator

5 Oxygen generator 10 Dust filter

1 Compressor 6 Purity measurement line

2 Refrigerant dryer 7 Ball valve

3 Filters DD-PD-QD 8 Oxygen tank

4 Air receiver 9 Pressure regulator

5 Oxygen generator 10 Dust filter

11 Non-return valve

Page 5: Oxygen Generator Systems - p-mgs.com · • Atlas Copco’s FX refrigerated dryer module • Atlas Copco DD+ and PD+ high efficiency filters • Accessories Options • Advanced T5

Pneumatech Medical Gas Solutions • Email: [email protected] • www.p-mgs.com• The right is reserved to change this technical specification without prior notice

Technical Datasheet81

0234

1150

Ed1

Pag

e 5

Typical Duplex Installation With Booster And Filling Ramp

1 Compressor 8 Oxygen tank

2 Refrigerant dryer 9 Pressure regulator

3 Filters DD-PD-QD 10 Dust filter

4 Air receiver 11 Non-return valve

5 Oxygen generator 12 High pressure booster

6 Purity measurement line 13 Pressure switch

7 Ball valve 14 Filling station

Page 6: Oxygen Generator Systems - p-mgs.com · • Atlas Copco’s FX refrigerated dryer module • Atlas Copco DD+ and PD+ high efficiency filters • Accessories Options • Advanced T5

Pneumatech Medical Gas Solutions • Email: [email protected] • www.p-mgs.com• The right is reserved to change this technical specification without prior notice

Technical Datasheet81

0234

1150

Ed1

Pag

e 6

Typical Simplex Containerised Installation With Booster And Filling Ramp

OXYGEN FILLING STATION WITH 6 OUTLETS113 T5 CONTROL BOX112 FUSE BOX111 RIX 4V4 AL BOOSTER110 PARKER TGA108 FILTER19 FILTER REGULATOR18 OXYGEN RECEIVER17 EXHAUST PIPE (SILENCER)16 OGP35 GENERATOR15 AIR RECEIVER14 DD-PD-QD130+ FILTER SET 13 FX17 DRYER12 GA30+ COMPRESSOR11

CommentsNameQtyPos

Drawn by Reviewed by Approved by - date Scale

VersionDrawing no.

Title

Paper size

Gazcon A/SOldvej 1A - DK 3540 LyngePhone5 44 99 69 00Fax +45 44 99 69 03 A3

SS

CONTAINERIZED O35 OXYGEN GENERATOR

1:20

Pos Amount Description Weight Dimensions (LxWxH)

1 2 3 4 5 6 7 8 9

A

10

B

C

D

E

F

G

agreed by us this document

may constitute a contractual

obligation on our part.

Only to the extent expressly

transmitted or communicated to any other party

property and must not be copied, reproduced,

or used for purposes not expressly perm

itted by us.

This document and its contents are our exclusive

Note:All measurements to be verified at time of installation.

1

2

3

4

5

7

8

9

10

11

6

12

2438

2352

6058

863

863

5897

24217644941023650

8018503501420500

276

1800

800

780

1020 96

893

R1176

2730

2630

2430

2172

1560

910

1800

2350

457

37

450

50

500

50

250

13

1 Compressor 8 Filter Regulator

2 Refrigerant dryer 9 TGA108 Filter

3 Filters DD-PD-QD 10 High pressure booster

4 Air receiver 11 Fuse Box

5 Oxygen generator 12 Controller

6 Exhaust Pipe (Silencer)

13 Oxygen Filling Station

7 Oxygen tank

OXYGEN FILLING STATION WITH 6 OUTLETS113 T5 CONTROL BOX112 FUSE BOX111 RIX 4V4 AL BOOSTER110 PARKER TGA108 FILTER19 FILTER REGULATOR18 OXYGEN RECEIVER17 EXHAUST PIPE (SILENCER)16 OGP35 GENERATOR15 AIR RECEIVER14 DD-PD-QD130+ FILTER SET 13 FX17 DRYER12 GA30+ COMPRESSOR11

CommentsNameQtyPos

Drawn by Reviewed by Approved by - date Scale

VersionDrawing no.

Title

Paper size

Gazcon A/SOldvej 1A - DK 3540 LyngePhone5 44 99 69 00Fax +45 44 99 69 03 A3

SS

CONTAINERIZED O35 OXYGEN GENERATOR

1:20

Pos Amount Description Weight Dimensions (LxWxH)

1 2 3 4 5 6 7 8 9

A

10

B

C

D

E

F

G

agreed by us this document

may constitute a contractual

obligation on our part.

Only to the extent expressly

transmitted or communicated to any other party

property and must not be copied, reproduced,

or used for purposes not expressly perm

itted by us.

This document and its contents are our exclusive

Note:All measurements to be verified at time of installation.

1

2

3

4

5

7

8

9

10

11

6

12

2438

2352

6058

863

863

5897

24217644941023650

8018503501420500

276

1800

800

780

1020 96

893

R1176

2730

2630

2430

2172

1560

910

1800

2350

457

37

450

50

500

50

250

13

OXYGEN FILLING STATION WITH 6 OUTLETS113 T5 CONTROL BOX112 FUSE BOX111 RIX 4V4 AL BOOSTER110 PARKER TGA108 FILTER19 FILTER REGULATOR18 OXYGEN RECEIVER17 EXHAUST PIPE (SILENCER)16 OGP35 GENERATOR15 AIR RECEIVER14 DD-PD-QD130+ FILTER SET 13 FX17 DRYER12 GA30+ COMPRESSOR11

CommentsNameQtyPos

Drawn by Reviewed by Approved by - date Scale

VersionDrawing no.

Title

Paper size

Gazcon A/SOldvej 1A - DK 3540 LyngePhone5 44 99 69 00Fax +45 44 99 69 03 A3

SS

CONTAINERIZED O35 OXYGEN GENERATOR

1:20

Pos Amount Description Weight Dimensions (LxWxH)

1 2 3 4 5 6 7 8 9

A

10

B

C

D

E

F

G

agreed by us this document

may constitute a contractual

obligation on our part.

Only to the extent expressly

transmitted or communicated to any other party

property and must not be copied, reproduced,

or used for purposes not expressly perm

itted by us.

This document and its contents are our exclusive

Note:All measurements to be verified at time of installation.

1

2

3

4

5

7

8

9

10

11

6

12

2438

2352

6058

863

863

5897

24217644941023650

8018503501420500

276

1800

800

780

1020 96

893

R1176

2730

2630

2430

2172

1560

910

1800

2350

457

37

450

50

500

50

250

13


Recommended