MASTER PULLER SETS IN PORTABLE CASES PULLERS AND PULLER SETS WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES 337 SET NO. 4290B 6 TON STANDARD PULLER SET • Makes over 20 of the most often used pullers: Internal, External, Slide Hammer, Rear Axle, Harmonic Balancer, etc. No. Description Qty. 4260R T-Handles Rod, 24" Long 1 4260H Slide Hammer, 2 1 /2 lb. 1 4250N Reversible Adjusting Nut 1 4250B Two Jaw Yoke 1 4255B Three Jaw Yoke 1 4205B Slotted Crossarm, 2 Way/ 3 Way 1 4056-6 Reversible Jaw, 6" Reach 3 4056-4 Reversible Jaw, 4" Reach 3 4056-2 Inside Jaw, 2" Reach 2 4056PN Jaw Pivot Pin 3 4256S Inside Hook Jaw 1 4205S Forcing Screw 1 4022T Standard Detachable Tip 1 4028 Cap Screw, 3 /8"-16" x 3" 3 4005C Cap Screw, 3 /8"-24" x 3" 3 4205E Cap Screw, 3 /8"-16" x 4" 3 4055H Slide Hammer, 5 lb. 1 4275R Short Slide Rod, 12 3 /4" Long 1 4277B Rear Axle Flange Foot 1 4280 Blind Bearing Adapter 1 4331 Gear and Bearing Separator 1 4951PB Molded Plastic Case 1 Weight: 27.68 lbs. Fed’l Specs.: GGG-P-781D SET NO. 4291B 6 TON WIDE PULLER SET • Designed for pulling machine parts up to 8" in diameter with reach depths to over 7". • Makes over 12 different adjustable and straight jaw pullers. No. Description Qty. 4205S Forcing Screw 1 4022T Standard Detachable Tip 1 4208CA 2 Way/ 3 Way Crossarm, 7" Long 1 4027 Long Narrow Jaw, 4" Reach 3 4026A Dual-Reach Jaws 3 4021S Spring Clip 3 4211BA Adjustable Jaw Block Assembly 3 4206SC Slotted Crossarm, 2 Way 1 4028 Cap Screw, 3 /8"-16" x 3" 2 4332 Bearing Separator, 4 3 /8" Capacity 1 4055H Slide Hammer, 5 lb. 1 4260R T-Handles Rod, 24" Long 1 4952PB Molded Plastic Case 1 Weight: 29.00 lbs. Fed’l Specs.: GGG-P-781D PROTECTIVE BLANKETS NO. 5046/5047 • Think of them as ”security blankets” • They wrap around pulling, pressing, and other high-force jobs to protect you and your employees from work-related injuries as much as possible • They’re made of high tensile, tear resistant ballistic nylon—similar to military flak jackets—that, when tested, withstood the shattering of a necked-down grade 8 bolt without any visible damage Note: Always reduce the force from the work piece prior to removing the blanket. Protective blankets may afford protection from injuries to users and others should part breakage occur. Because of the variety of situations that require guarding, it is the user’s responsibility to determine the best method of protection. NEW! NEW! 5046 12" x 30" Weight 2.3 lbs. 5047 20" x 36" Weight 3 lbs.
Transcript
MASTER PULLER SETS IN PORTABLE CASES PU
LLERSA
ND
PU
LLERS
ETS
WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES 337
SET NO. 4290B6 TON STANDARD PULLER SET• Makes over 20 of the most often used pullers: Internal, External, Slide
Hammer, Rear Axle, Harmonic Balancer, etc.
No. Description Qty.
4260R T-Handles Rod, 24" Long 14260H Slide Hammer, 21⁄2 lb. 14250N Reversible Adjusting Nut 14250B Two Jaw Yoke 14255B Three Jaw Yoke 14205B Slotted Crossarm, 2 Way/ 3 Way 14056-6 Reversible Jaw, 6" Reach 34056-4 Reversible Jaw, 4" Reach 34056-2 Inside Jaw, 2" Reach 24056PN Jaw Pivot Pin 34256S Inside Hook Jaw 14205S Forcing Screw 14022T Standard Detachable Tip 14028 Cap Screw, 3⁄8"-16" x 3" 34005C Cap Screw, 3⁄8"-24" x 3" 34205E Cap Screw, 3⁄8"-16" x 4" 34055H Slide Hammer, 5 lb. 14275R Short Slide Rod, 123⁄4" Long 14277B Rear Axle Flange Foot 14280 Blind Bearing Adapter 14331 Gear and Bearing Separator 14951PB Molded Plastic Case 1
Weight: 27.68 lbs.Fed’l Specs.: GGG-P-781D
SET NO. 4291B6 TON WIDE PULLER SET• Designed for pulling machine parts up to 8" in diameter with reach depths
to over 7".• Makes over 12 different adjustable and straight jaw pullers.
No. Description Qty.
4205S Forcing Screw 14022T Standard Detachable Tip 14208CA 2 Way/ 3 Way Crossarm, 7" Long 14027 Long Narrow Jaw, 4" Reach 34026A Dual-Reach Jaws 34021S Spring Clip 34211BA Adjustable Jaw Block Assembly 34206SC Slotted Crossarm, 2 Way 14028 Cap Screw, 3⁄8"-16" x 3" 24332 Bearing Separator, 43⁄8" Capacity 14055H Slide Hammer, 5 lb. 14260R T-Handles Rod, 24" Long 14952PB Molded Plastic Case 1
Weight: 29.00 lbs.Fed’l Specs.: GGG-P-781D
PROTECTIVE BLANKETS NO. 5046/5047• Think of them as ”security blankets” • They wrap around pulling, pressing, and other high-force jobs to protect you and your employees from work-related injuries as much as possible • They’re made of high tensile, tear resistant ballistic nylon—similar to military flak jackets—that, when tested, withstood the shattering of a necked-down grade 8 bolt without any visible damage Note: Always reduce the force from the work piece prior to removing the blanket. Protective blankets may afford protection from injuries to users and others should partbreakage occur. Because of the variety of situations that require guarding, it is the user’s responsibility to determine the best method of protection.
NEW! NEW!
5046 12" x 30" Weight 2.3 lbs. 5047 20" x 36" Weight 3 lbs.
PULL
ERS
AN
DPU
LLER
SETS
338
MASTER PULLER SETS IN PORTABLE CASES
WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES
SET NO. 4292B10 TON WIDE PULLER SET• Required for large parts with heavy press-fits.• Reaches to over 12" and spread of 11"• Makes over 10 different adjustable and straight jaw pullers.
No. Description Qty.
4225S Forcing Screw 14012T Standard Detachable Tip 14226CA 2 Way Crossarm, 11" Long 14227CA 3 Way Crossarm, 11" Long 14231A Adjustable Jaw Block Assembly 34016A Dual Reach Jaws 34018 Cap Screw Jaw, 215⁄16" Reach 34017 Long Narrow Jaw, 73⁄16" Reach 34011S Jaw Spring Clip 34333 Bearing Separator, 6" Capacity 14953PB Molded Plastic Case 1
Weight: 39.00 lbs.Fed’l Specs.: GGG-P-781D
SET NO. 4293B10 TON PRESS-N-PULLTM SET• Presses parts into place without hydraulics.• Functions as many different pullers either by itself or in combination with
other Proto Pullers.
No. Description Qty.
4012T Tip, Forcing Screw 14229LS Lock Screw, 7⁄16"-14" x 3⁄4" 34235AA Adapter, 3⁄4"-12 Fem. x 5⁄8" M, Acme 14235CN Coupling Nut, 3⁄4"-12 Acme 14235S Forcing Screw, 3⁄4"-12" Acme x 12" 14235UA Adapter, 3⁄4"-12 Fem. Acme x 5⁄8"-18NF Male 14236CA 2 Way Crossarm 14236N Forcing Nut, 3⁄4"-12" Acme 14236W Thrust Washer 14237CA 3 Way Crossarm 14239SB Slide Block 34240-08F Adapter, 5⁄8"-18 Fem. x 1⁄2"-20 Fem. 34240-08M Adapter, 5⁄8"-18 Fem. x 1⁄2"-20 Male 34240-12F Adapter, 5⁄8"-18 Fem. x 3⁄4"-16 Fem. 34240-12M Adapter, 5⁄8"-18 Fem. x 3⁄4"-16 Male 34240-14F Adapter, 5⁄8"-18 Fem. x 7⁄8"-14 Fem. 34240-14M Adapter, 5⁄8"-18 Fem. x 7⁄8"-14 Male 34240L Medium Leg 34240SL Short Leg 34333 Bearing Separator 14954PB Molded Plastic Case 1
Weight: 43.00 lbs.Fed’l Specs.: GGG-P-781D
SET NO. 4390BBEARING SEPARATOR SET• Removes gears and bearings too close to another surface for puller jaw
grip, or where the pulled out part must be protected.• Case provides space for step plates and assorted accessories.
No. Description Qty.
4330 Gear and Bearing Separator, 113⁄16" Capacity 14331 Gear and Bearing Separator, 213⁄32" Capacity 14332 Gear and Bearing Separator, 43⁄8" Capacity 14333A Gear and Bearing Separator, 6" Capacity 14333R Threaded Rod, 3⁄4"-16UNF, 10" Long 24955PB Molded Plastic Case 1
Weight: 27.50 lbs.
MASTER PULLER SETS PU
LLERSA
ND
PU
LLERS
ETS
WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES 339
SET NO. 4235B (with box)MASTER PULLER SET• Covers most maintenance operations using standard pullers.• Contains all components necessary to assemble all full-interchange
system pullers except Press-N-Pull™.
No. Description Qty.
4205B Slotted Crossarm, 2 Way/3 Way 14022T Puller Tip 14205S Forcing Screw 14005C Cap Screw, 3⁄8"-24" x 3" 34205E Cap Screw, 3⁄8"-16" x 4" 34028 Cap Screw, 3⁄8"-16" x 3" 34206SC Slotted Crossarm, 2 Way 14250B 2 Way Yoke 14255B 3 Way Yoke 14056-2 Inside Jaw, 2" Reach 34056-4 Reversible Jaw, 4" Reach 34056-6 Reversible Jaw, 6" Reach 34250N Reversible Adjusting Nut 14256PN Jaw Pivot Pin 34260H 21⁄2 lb. Slide Hammer 14260R T-Handle Slide Rod 14055H 5 lb. Slide Hammer 14275R Short Slide Rod 14277B Axle Flange 14256S Inside Hook Jaw 14280 Blind Bearing Puller 14211BA Jawblock Assembly 34026A Jaw, Dual-Reach 34027 Jaw, Long Narrow 34208CA 2 Way/3 Way Crossarm 14231A Jawblock Assembly 34012T Puller Tip 14225S Forcing Screw 14226CA 2 Way Crossarm 14227CA 3 Way Crossarm 14016 Jaw, Dual-Reach 34017 Jaw, Long Narrow 34018 Jaw, Cap Screw 34021S Jaw Spring, 6 Ton 34011S Jaw Spring, 10 Ton 34331 Bearing Separator, 23⁄8" Capacity 14333A Bearing Separator, 6" Capacity 14040 Step Plate Adapter Set 14040-12 Step Plate, 21⁄8" Bore 14040-13 Step Plate, 21⁄4" Bore 14040-14 Step Plate, 23⁄8" Bore 19969 Steel Box 1
Weight: 93.00 lbs.
SET NO. 4245 GENERAL PULLER SET• Includes components to assemble a wide variety of 3 ton, 6 ton, 10 ton,
slide hammer and threaded part pullers.
No. Description Qty.
4005C Cap Screw, 3⁄8"-24NF x 3" 34011S 10 Ton Jaw Spring 34016A 10 Ton Dual-Reach Jaw 411⁄16" and 71⁄8" 14017 10 Ton Narrow Jaw 73⁄16" 14018 10 Ton Cap Screw, 215⁄16" Reach 14021S 6 Ton Jaw Spring 34026A 6 Ton Duel Reach Jaw, 2" and 4" 34027 6 Ton Narrow Jaw, 4" Reach 34040 Step Plate Adapter Set, 3⁄4" to 21⁄2" Bore Diameter 14056-2 3 Ton Inside Jaw, 2" Reach 24205B 6 Ton 2-Way/3-Way Slotted Crossarm, 5" 14205E Cap Screw, 3⁄8"-16NC x 4" 34206CA 6 Ton 2-Way Crossarm, 7" 14208CA 6 Ton 2-Way/3-Way Crossarm, 7" 14227CA 10 Ton 3-Way Crossarm, 11" 14234 10 Ton 2-Way Straight Jaw Puller Set 14252 6 Ton 2-Way/3-Way Cone Type Puller Set 14256S 6 Ton Inside-Hook Jaw 14260H 21⁄2 lb. Slide Hammer 14260R T-Handle Slide Rod 14280 Blind Bearing Puller 14331 Gear and Bearing Separator, 23⁄8" Capacity 14332 Gear and Bearing Separator, 43⁄8" Capacity 1
Weight: 46.13 lbs.
6 TON PROTO-EASE™ CONE PULLERS PU
LLERSA
ND
PU
LLERS
ETS
WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES 341
SET NO. 42526 TON 2-WAY/3-WAY CONE PULLER SET• Reach: 4" and 6"—Spread: 5" and 7".
NO. 4233SJ10 TON 3-WAY STRAIGHT JAW PULLER• Reach: 411⁄16" and 71⁄8"—Spread: 10".
No. Description Qty.
4011S Spring Clip 34012T Detachable Tip 14016A Dual Reach Jaw, 411⁄16" and 71⁄8" Reach 34225S Forcing Screw 14227CA 3-Way Crossarm, 11" 1
Weight: 9.00 lbs.Fed’l Specs.: GGG-P-781D
PULL
ERS
AN
DPU
LLER
SETS
346
10 TON PROTO-EASETM PULLERS
WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES
SET NO. 4234B10 TON 2-WAY STRAIGHT JAW PULLER SET• Reach: 215⁄16", 411⁄16" and 71⁄8" (18" with jaws bolted together)—Spread: 10".• Includes Steel Storage Box.
No. Description Qty.
4011S Spring Clip 24012T Detachable Tip 14016A Dual Reach Jaw, 411⁄16" and 71⁄8" Reach 24017 Narrow Jaw, 73⁄16" Reach 24018 Cap Screw Jaw, 215⁄16" Reach 24225S Forcing Screw 14226CA 2-Way Crossarm, 11" 14019 Steel Storage Box 1
Weight: 15.37 lbs. Fed’l Specs.: GGG-P-781D
SET NO. 4232SJ10 TON 2-WAY STRAIGHT JAW PULLER SET• Reach: 411⁄16" and 71⁄8" (12" with jaws bolted together)—Spread: 10".
No. Description Qty.
4011S Spring Clip 24012T Detachable Tip 14015 Straight Jaw, 411⁄16" Reach 24016A Dual Reach Jaw, 411⁄16" and 71⁄8" Reach 24225S Forcing Screw 14226CA 2-Way Crossarm, 11" 1
Weight: 8.68 lbs. Fed’l Specs.: GGG-P-781D
PULL
ERS
AN
DP U
LLER
S ETS
348
10 TON PRESS-N-PULLTM PULLERS
WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES
SET NO. 4293SP-STK10 TON PRESS-N-PULLTM 3-LEG PULLER SET• Reach: 22 "—Spread: 11".
No. Description Qty.4012T Detachable Tip 14229LS Lock Screw, 7⁄16-14 x 3⁄4 34236CA 2-Leg Crossarm, 11" 14237CA 3-Leg Crossarm, 11" 14235S Forcing Screw 14235AA Forcing Screw Adapter 3⁄4" to 5⁄8" Acme 14235UA Forcing Screw Adapter 3⁄4" to 5⁄8" UNF 14235CN Forcing Screw Coupling Nut, 3⁄4" Acme 14236N Forcing Nut 14236W Thrust Washer 14239SB Leg Slideblock 34240SL Medium Leg 34240L Short Leg 34240P Leg Pressure Pad 34240-08F Female Adapter, 5⁄8" to 1⁄2" UNF 34240-08M Male Adapter, 5⁄8" to 1⁄2" UNF 34240-12F Female Adapter, 5⁄8" to 3⁄4" UNF 34240-12M Male Adapter, 5⁄8" to 3⁄4" UNF 34240-14F Female Adapter, 5⁄8" to 7⁄8" UNF 34240-14M Male Adapter, 5⁄8" to 7⁄8" UNF 34332 Bearing Separator, 43⁄8" Capacity 1
Weight: 35.24 lbs. Fed’l Specs.: GGG-P-781D
NO. 424210 TON PRESS-N-PULLTM 2-LEG PULLER• Reach: 14"—Spread: 11"
No. Description Qty.
4012T Detachable Tip 14229LS Lock Screw, 7⁄16-14 x 3⁄4 24235S Forcing Screw 14236CA 2-leg Crossarm,11" 14236N Forcing Nut 14236W Thrust Washer 14239SB Leg Slideblock 24240L Medium Leg 24240P Leg Pressure Pad 2
Weight: 9.18 lbs.Fed’l Specs.: GGG-P-781D
PULL
ERS
AN
DP U
LLER
S ETS
350
6 TON PROTO-EASETM SLIDE HAMMER PULLERS
WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES
Weight: 25 lbs.
Weight: 3.8 lbs.
SET NO. 42856 TON 2-WAY/3-WAY SLIDE HAMMER PULLER SET• Reach: 6"—Spread: 7".
Slotted crossarm puller used to remove a universal joint flange.
SET NO. 5035STEERING WHEEL REMOVER/LOCK PLATE COMPRESSOR SET• Removing steering wheels of most domestic and imported vehicles, with
or without telescoping tilt steering columns, is easy with this new set.• You get steering wheel puller, including four sets of cap screws needed
for various thread requirements.• The steering wheel lock plate compressor is also included, to compress
the steering wheel lock plate to remove or install the snap ring.• It accesses the turn signal switch and S.I.R. modules on current GM vehi-
cles; also works on older GM, AMC, and Chrysler vehicles with tilt or conventional steering columns.
• The steering pivot pin remover for Saginaw steering columns completes the set. Contained in convenient plastic storage tray.
Set consists of Qty.1⁄4" – 28" x 3" lg. capscrew 13⁄8" – 24" x 1 1⁄2" lg. capscrew 13⁄8" – 16" x 2" lg. capscrew 13⁄8" – 16" x 3" lg. capscrew 13⁄8" – 16" x 4 1⁄2" lg. capscrew 25⁄16" – 24" x 3" lg. capscrew 25⁄16" – 18" x 3 1⁄2" lg. capscrew 25⁄16" – 18" x 6" lg. capscrew 2M8 x 1.25 x 45 mm lg. capscrew 2M8 x 1.25 x 65 mm lg. capscrew 2M8 x 1.25 x 90 mm lg. capscrew 2M10 x 1.5 x 35 mm lg. capscrew 2
Weight: 6.10 lbs.Fed’l Specs.: GGG-P-781D
SET NO. 5048STEERING WHEEL PULLER LEG KIT• Particularly useful during steering wheel removal when there are no
tapped holes in the assembly.• These legs get behind the steering wheel assembly to provide an even,
straight pull. The collar is designed for use on Ford and Chrysler vehicles.• Works on: PONTIAC: 1988-’93 Lemans, 1997-current Grand Prix Trans Sport
Van; CADILLAC: 1997-current Catera; BUICK: 1997-current Park Avenue, Regal; CHEVROLET/GMC: 1997-current Malibu, Corvette, 1998-current C- and K-Series trucks, full-size vans, and Astro/Safari vans; FORD: 1997-current Explorers, F-150 and Ranger pickups; CHRYSLER: 1999 Jeep Grand Cherokee
Weight 4.5 lbs. Weight 5 oz.
NEW!
NEW!
NEW!
STEP PLATE ADAPTERS AND CAP SCREW PULLERS PU
LLERSA
ND
PU
LLERS
ETS
WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES 355
DRIVER TOOLS, BUSHING REMOVER SETS• Have the proper-size driver for any seal, bearing or bushing installing job. • Sets include discs and handles you assemble to provide a pilot (to
prevent cocking), a spacer (so force is applied on the proper area), and a driver (for even force distribution).
NO. 5037STARTER SET (pictured above)• Discs range in size from 5⁄8" - 2" in diameter, in 1⁄16" increments.• Includes blow mold case.NO. 5038BASIC SET• 41 discs range in size from 1⁄2"-3" in diameter, in 1⁄16" increments.• Includes 2 handles.
NO. 50506 TON HARMONIC BALANCER AND STEERINGWHEEL PULLER• Pulls harmonic balancers, steering wheels, timing gears and parts having
two or three tapped holes. • Slotted holes in puller body permit cap screws to be positioned to handle
bolt-circle diameters from 1-1⁄2" to 4-5⁄8".• Includes six cap screws; three 3⁄8"-24 x 3" long and three 3⁄8"-16 x 3".• A plastic storage case helps you keep set components organized for
easy selection.
Harmonic balancer puller used to remove the crankshaft damper(harmonic balancer).
SET NO. 404011 PC. STEP PLATE ADAPTER SET• Includes Nos. 4040-1 thru 4040-11.• For bore diameter 3⁄4" to 2".
Toggle type pullers incorporate an automatic grip-tightening feature and are an economical choice for jobs whereprecision grip is not important. Forcing screws are forged from alloy steel and heat treated to the right combination ofhardness and strength. Pullers on this page are non-interchange series.
NO. 40463 JAW GEAR PULLER, 7"—REVERSIBLEMaximum Maximum Forcing
WORK SAFELY WITH TOOLS BY WEARING SAFETY GOGGLES 357
Toggle type pullers incorporate an automatic grip-tightening feature and are an economical choice for jobs whereprecision grip is not important. Forcing screws are forged from alloy steel and heat treated to the right combination ofhardness and strength. Pullers on this page are non-interchange series.
NO. 40332 JAW GEAR PULLER, 4"Maximum Maximum Forcing
