Leaflet-No. 0704.01.08 EN Replaces No. 0704.08.07 EN Page 1 of 8 Pump aggregate GMG-B Pump aggregate GMG-B Use: As pump aggregate in central lubrication systems + + + + + for the delivery of oil, liquid grease or grease 1 or 2 pump outlets up to 20 outlets with progressive distributor flanged-on electric control and monitoring with function stirring without delivery Technical data: Admissible delivery pressure: at max. 250 bar Number of pump elements: at max. 2 Delivery volume per stroke and element with pump element 08: 0,08 cm³ with pump element 16: 0,16 cm³ Temperature range: -20 ... +60 °C At low temperatures, grease pene- tration needs to be observed. Mounting position: vertically Material Casing: Aluminium Pump element: Steel Reservoir:Steel /Polyamide transparent Gaskets: NBR (Perbunan) Medium: Oil and grease up to NLGI class 2 (Mind conditions of use of both the reservoir and filling level monitoring device!) Drive: Mains voltage: 24 VDC Current at max.: 2,5A Speed (load-dependent): approx. 30 min System of protection: IP 55 -1 ( .) Depending on type of construction, the DC gear motor should only be used in pulse mode. For other modes of operation, three-phase current motors are of advantage (e.g. Pump aggregate GMA-C) EUGEN WOERNER GmbH & Co. KG Postfach 1661 DE-97866 Wertheim Am Eichamt 8 DE-97877 Wertheim Tel. +49 (0) 9342 803-0 Fax.+49 (0) 9342 803-202 www.woerner.de [email protected]- Subject to modifications -
Transcript
Leaflet-No. 0704.01.08 ENReplaces No. 0704.08.07 EN
Page 1 of 8
Leaflet-No. 0704 EN
Page 2 of 8
Description:
Drive:
5 4
Delivery function:
32.1
1
Function stirring without delivery:
3
3
The pump aggregate GMG-B is driven by agear motor flanged to the pump casingfrom downside.
When the eccentric shaft rotates, thedlivery piston of every pump elementmakes a suction and delivery stroke perrotation each, whilst delivering lubricantfrom the reservoir to the lubricationpoints.
.
.
GMG-B.
.
.
.
Pump elements:
suction stroke2.2 2.1
31
2.32.4
delivery stroke 32.1
2.3
2.42.5 2.6
R
At , the pressure springmoves the delivery piston against
the eccentric shaft . Concurrently, thelubricant available in the reservoir isdrawn through the suction hole into themetering chamber .
At , the eccentric shaftshifts the delivery piston . At the sametime, the suction hole is closed up andthe lubricant volume available in themetering chamber delivered throughthe check valve to the outlet .
The 0,16 cm³ delivery volume pump ele-ment is marked by a black ring .
Depending on the case of operation(lubricant, lubricant requirement, etc.), thepump aggregate can be fitted with differentpump elements, reservoirs, and monitoringelements
In some modes of operation, improvementof lubricant quality and delivery behaviourrequires the lubricant to be stirredadditionallySuch stirring is facilitated in the pumpaggregate by means of a specifi-cally designed eccentric driveWhen the eccentric shaft rotates into theone direction of rotation, the pump elementsare operating while the stirring devicesupplies them with the lubricantAs soon as the eccentric shaft starts torotate into the other direction, the lubricantis stirred without any delivery operation bythe pump elements taking place
The integrated control unit allows operatingand off-duty periods for both the deliverywith and without stirring to be programmedindependently from each other
Pump aggregate GMG-B
Pump aggregate
GMG-B
Use:
As pump aggregate in central lubricationsystems
+
+
+
+
+
for the delivery of oil, liquid grease orgrease
1 or 2 pump outlets
up to 20 outlets with progressivedistributor flanged-on
electric control and monitoring
with function stirring withoutdelivery
Technical data:
Admissibledelivery pressure: at max. 250 bar
Number of pump elements: at max. 2
Delivery volume per stroke and elementwith pump element 08: 0,08 cm³with pump element 16: 0,16 cm³
Temperature range: -20 ... +60 °CAt low temperatures, grease pene-tration needs to be observed.
Medium: Oil and grease up to NLGI class 2(Mind conditions of use of both thereservoir and filling level monitoringdevice!)
Drive:Mains voltage: 24 VDCCurrent at max.: 2,5ASpeed(load-dependent): approx. 30 minSystem of protection: IP 55
-1
(
.)
Depending on type of construction, theDC gear motor should only be usedin pulse mode. For other modes ofoperation, three-phase current motorsare of advantage (e.g. Pump aggregateGMA-C)
Leaflet-No. 0704.01.08 ENReplaces No. 0704.08.07 EN
Page 1 of 8
Leaflet-No. 0704 EN
Page 2 of 8
Description:
Drive:
5 4
Delivery function:
32.1
1
Function stirring without delivery:
3
3
The pump aggregate GMG-B is driven by agear motor flanged to the pump casingfrom downside.
When the eccentric shaft rotates, thedlivery piston of every pump elementmakes a suction and delivery stroke perrotation each, whilst delivering lubricantfrom the reservoir to the lubricationpoints.
.
.
GMG-B.
.
.
.
Pump elements:
suction stroke2.2 2.1
31
2.32.4
delivery stroke 32.1
2.3
2.42.5 2.6
R
At , the pressure springmoves the delivery piston against
the eccentric shaft . Concurrently, thelubricant available in the reservoir isdrawn through the suction hole into themetering chamber .
At , the eccentric shaftshifts the delivery piston . At the sametime, the suction hole is closed up andthe lubricant volume available in themetering chamber delivered throughthe check valve to the outlet .
The 0,16 cm³ delivery volume pump ele-ment is marked by a black ring .
Depending on the case of operation(lubricant, lubricant requirement, etc.), thepump aggregate can be fitted with differentpump elements, reservoirs, and monitoringelements
In some modes of operation, improvementof lubricant quality and delivery behaviourrequires the lubricant to be stirredadditionallySuch stirring is facilitated in the pumpaggregate by means of a specifi-cally designed eccentric driveWhen the eccentric shaft rotates into theone direction of rotation, the pump elementsare operating while the stirring devicesupplies them with the lubricantAs soon as the eccentric shaft starts torotate into the other direction, the lubricantis stirred without any delivery operation bythe pump elements taking place
The integrated control unit allows operatingand off-duty periods for both the deliverywith and without stirring to be programmedindependently from each other
Pump aggregate GMG-B
Pump aggregate
GMG-B
Use:
As pump aggregate in central lubricationsystems
+
+
+
+
+
for the delivery of oil, liquid grease orgrease
1 or 2 pump outlets
up to 20 outlets with progressivedistributor flanged-on
electric control and monitoring
with function stirring withoutdelivery
Technical data:
Admissibledelivery pressure: at max. 250 bar
Number of pump elements: at max. 2
Delivery volume per stroke and elementwith pump element 08: 0,08 cm³with pump element 16: 0,16 cm³
Temperature range: -20 ... +60 °CAt low temperatures, grease pene-tration needs to be observed.
Medium: Oil and grease up to NLGI class 2(Mind conditions of use of both thereservoir and filling level monitoringdevice!)
Drive:Mains voltage: 24 VDCCurrent at max.: 2,5ASpeed(load-dependent): approx. 30 minSystem of protection: IP 55
-1
(
.)
Depending on type of construction, theDC gear motor should only be usedin pulse mode. For other modes ofoperation, three-phase current motorsare of advantage (e.g. Pump aggregateGMA-C)
Switching voltage at max.: 30 VDCSwitching current at max.: 0,25ASwitching power at max.: 3,0 WFor inductive and capacitive loads protec-tive circuits (diode, RC-member, varistor)have to be provided for.
Level control "F":min. level monitoring for oil
The level control "F" consists of a float thatis lifted in the oil.If oil falls below minimum filling level, thecontact opened.
Reservoir "4P":
Notes on operation:
The pump aggregates must be operatedwith clean oil or grease from originalpackages only. During start-up, the pumphas initially to be filled with gear oil up tostirring blade level. Thus, proper venting isensured. The lines to the lubrication points
must be clean and have free throughput.They shall not be connected to the lub-rication points unless the lubricant comesout free of bubbles. All connectors of thedelivery line have to be checked forleakage.
To protect the pump aggregate and thelines connected from overload, protec-tive elements such as pressure controlvalves have to be integrated basically.
Level control:
Level control "C":min. level monitoring for grease
.
Version without control:
In case of empty reservoir and rotatingpump drive shaft, the contact is switched.
(approx. 5 seconds).
When "stirring without delivery", signalevaluation has to be suppressed.
The "Empty" signal is intermittentThe switching mechanism may shift as forinstance during reservoir filling. In case ofexternal control, signal evaluation musttherefore be delayed when the pump isswitched on
other reservoir versions available on request
Reservoir "1,5":
Capacity
[l]
1,5
Polyamide
translucent
Polypropylene
Polypropylene4
Reservoir "1,5"
Reservoir 4P""
Material
LidReservoir
Polyamide
translucent
Lubricant available(permanent signal)
No lubricant available:(intermittent signal)
Filling connector "W"Closing nipple
Filling connector:
This part is located beneath the left-sidepump element.
Filling connector "A"Cone lubricator nipple DIN 71412 - AG1/4
A
W
Filling connector "C"Flat lubricator nipple DIN 3404 - M22
C
Filling connector "G"Closing nipple
Accessory for filling connector "G" and "W":Quick release coupling 954.002-09
Switching voltage at max.: 30 VDCSwitching current at max.: 0,25ASwitching power at max.: 3,0 WFor inductive and capacitive loads protec-tive circuits (diode, RC-member, varistor)have to be provided for.
Level control "F":min. level monitoring for oil
The level control "F" consists of a float thatis lifted in the oil.If oil falls below minimum filling level, thecontact opened.
Reservoir "4P":
Notes on operation:
The pump aggregates must be operatedwith clean oil or grease from originalpackages only. During start-up, the pumphas initially to be filled with gear oil up tostirring blade level. Thus, proper venting isensured. The lines to the lubrication points
must be clean and have free throughput.They shall not be connected to the lub-rication points unless the lubricant comesout free of bubbles. All connectors of thedelivery line have to be checked forleakage.
To protect the pump aggregate and thelines connected from overload, protec-tive elements such as pressure controlvalves have to be integrated basically.
Level control:
Level control "C":min. level monitoring for grease
.
Version without control:
In case of empty reservoir and rotatingpump drive shaft, the contact is switched.
(approx. 5 seconds).
When "stirring without delivery", signalevaluation has to be suppressed.
The "Empty" signal is intermittentThe switching mechanism may shift as forinstance during reservoir filling. In case ofexternal control, signal evaluation musttherefore be delayed when the pump isswitched on
other reservoir versions available on request
Reservoir "1,5":
Capacity
[l]
1,5
Polyamide
translucent
Polypropylene
Polypropylene4
Reservoir "1,5"
Reservoir 4P""
Material
LidReservoir
Polyamide
translucent
Lubricant available(permanent signal)
No lubricant available:(intermittent signal)
Filling connector "W"Closing nipple
Filling connector:
This part is located beneath the left-sidepump element.
Filling connector "A"Cone lubricator nipple DIN 71412 - AG1/4
A
W
Filling connector "C"Flat lubricator nipple DIN 3404 - M22
C
Filling connector "G"Closing nipple
Accessory for filling connector "G" and "W":Quick release coupling 954.002-09
The control unit serves to monitor andtrigger the pump aggregate. It is capable ofswitching the pump on and off depending ontime and load. Besides, the control unit canbe used to monitor the filling level andfunctionality of the progressive distributorIn case of failure, a corresponding messagecan be made accessible to a higher rankingsystemThe control unit must be started via anexternal
E1 = Motor overloadedE2 = Progressive distributor faultyE3 = Level faultFault messages can be deleted by keepingthe “SAVE” key depressed for a while.
Fault Description:
.
.
"release".
Power consumption: 1,7 WSupply voltage: 24 VDC ± 5 %Voltage at inputs: 24 VDCResponse time of inputs: 200 msInput resistance: 4 kTemperature range: -20 °C ... +60 °COutlet alarm: 200 mA/ 24 VDC / 60WData buffer: 10 years
Control variant "B":
Control variant "B1":
Control variant "B2":
Control without distributor monitoring.
Control with distributor monitoring for pro-gressive distributor flanged on.
Control with distributor monitoring for ex-ternally mounted progressive distributor(with functional checking device "RS"). Forconnecting cable see "Auxiliaries" below.
Technical data:
Ù
At the right-side pump element, progressivedistributors of the VPB type can be flangedon directly. As much as 20 lubrication pointswith different distribution volumes arepossible. A selection of progressive distri-butors can be chosen by means of theGMG-B purchase-designation.
By monitoring the movement of one distri-butor piston, the lubricant allocation to alloutlets is monitored. Evaluation through thepump control unit requires selection of aprogressive distributor fitted with the func-tion control
In case of oil, metering accuracydepends on viscosity, flow resistance atthe outlets, and delivery speed.
Functionality:
Function control:
Technical data progressive distributor:
The lubricant supplied by the pump elementis delivered to the outlet progressively (i.e.progressing in the distributor).
RK.
Metering volume per cycleand outlet: 0,20 cm³
Lubrication point connectors: 4, 6 or 8other versions available on request(up to 20 lubrication points)
Operating pressure at max.: 150 bar
Delivery mediumOil-viscosity: as of approx. 140 cP
(equals ISO VG46 at 20°C)Grease up to: NLGI class 2
4 outletswithout function checking device "P4"with function checking device RK "P5"
6 outletswithout function checking device "P0"with function checking device RK "P1"
8 outletswithout function checking device "P2"with function checking device RK "P3"
Note on operation:
Note:
N
The 0,16 cm³ delivery volume pumpelement is marked by means of a greyplastic pimple .
Upon start-up, both pump element andprogressive distributor need to be vented.The lubricant must come out free of bubblesfrom all outlets.At first, the connecting case should bevented at venting screw or at the built-inpressure control valve. Then, the progres-sive distributor should be vented.
6
Auxiliaries:Pressure control valve at the pro-gressive distributor:
Opening pressure: Purchase-no.:
70 bar 110.566-65150 bar 110.564-65
Customised setting:50 - 150 bar 110.568-65
For delimitation of the maximum operatingpressure, pressure control valves insteadof the venting screw can be screwed in.
76
7
Control unit operation:
1. Menu call-up:By long pressing the "MODE” key, themenu structure is called up.
2. Navigation within the menus:By keeping the “Mode” key depressedanother time, the menu items P1 … P11can be selected successively.
3. Changing of values:The „SELECT“ key can be used tochange setting values and functions.In case of time data, short pressing ofthe “SELECT” key results in a shiftingby +1, whereas any longer pressing willresult in a shifting by +20. When the“SAVE” key is depressed for a while,the set values will be saved. Pressingthe “MODE” key enables the next menuitem to be accessed without any savingaction.
4. Special Functions:When the “SELECT” key is depressedin the operating mode “ON” for a while,pumping action will be carried out for 60seconds.
1
4 3
2
Flanged progressive distributor: Control unit:
1)Explanation:
Delivery function: 24 V to Pin 1Stirring function: 24 V to Pin 1 and 2
Auxiliaries
Cable jack for electric connection:
913.404-65913.405-07
Connecting cable for externally moun-ted progressive distributor:
The control unit serves to monitor andtrigger the pump aggregate. It is capable ofswitching the pump on and off depending ontime and load. Besides, the control unit canbe used to monitor the filling level andfunctionality of the progressive distributorIn case of failure, a corresponding messagecan be made accessible to a higher rankingsystemThe control unit must be started via anexternal
E1 = Motor overloadedE2 = Progressive distributor faultyE3 = Level faultFault messages can be deleted by keepingthe “SAVE” key depressed for a while.
Fault Description:
.
.
"release".
Power consumption: 1,7 WSupply voltage: 24 VDC ± 5 %Voltage at inputs: 24 VDCResponse time of inputs: 200 msInput resistance: 4 kTemperature range: -20 °C ... +60 °COutlet alarm: 200 mA/ 24 VDC / 60WData buffer: 10 years
Control variant "B":
Control variant "B1":
Control variant "B2":
Control without distributor monitoring.
Control with distributor monitoring for pro-gressive distributor flanged on.
Control with distributor monitoring for ex-ternally mounted progressive distributor(with functional checking device "RS"). Forconnecting cable see "Auxiliaries" below.
Technical data:
Ù
At the right-side pump element, progressivedistributors of the VPB type can be flangedon directly. As much as 20 lubrication pointswith different distribution volumes arepossible. A selection of progressive distri-butors can be chosen by means of theGMG-B purchase-designation.
By monitoring the movement of one distri-butor piston, the lubricant allocation to alloutlets is monitored. Evaluation through thepump control unit requires selection of aprogressive distributor fitted with the func-tion control
In case of oil, metering accuracydepends on viscosity, flow resistance atthe outlets, and delivery speed.
Functionality:
Function control:
Technical data progressive distributor:
The lubricant supplied by the pump elementis delivered to the outlet progressively (i.e.progressing in the distributor).
RK.
Metering volume per cycleand outlet: 0,20 cm³
Lubrication point connectors: 4, 6 or 8other versions available on request(up to 20 lubrication points)
Operating pressure at max.: 150 bar
Delivery mediumOil-viscosity: as of approx. 140 cP
(equals ISO VG46 at 20°C)Grease up to: NLGI class 2
4 outletswithout function checking device "P4"with function checking device RK "P5"
6 outletswithout function checking device "P0"with function checking device RK "P1"
8 outletswithout function checking device "P2"with function checking device RK "P3"
Note on operation:
Note:
N
The 0,16 cm³ delivery volume pumpelement is marked by means of a greyplastic pimple .
Upon start-up, both pump element andprogressive distributor need to be vented.The lubricant must come out free of bubblesfrom all outlets.At first, the connecting case should bevented at venting screw or at the built-inpressure control valve. Then, the progres-sive distributor should be vented.
6
Auxiliaries:Pressure control valve at the pro-gressive distributor:
Opening pressure: Purchase-no.:
70 bar 110.566-65150 bar 110.564-65
Customised setting:50 - 150 bar 110.568-65
For delimitation of the maximum operatingpressure, pressure control valves insteadof the venting screw can be screwed in.
76
7
Control unit operation:
1. Menu call-up:By long pressing the "MODE” key, themenu structure is called up.
2. Navigation within the menus:By keeping the “Mode” key depressedanother time, the menu items P1 … P11can be selected successively.
3. Changing of values:The „SELECT“ key can be used tochange setting values and functions.In case of time data, short pressing ofthe “SELECT” key results in a shiftingby +1, whereas any longer pressing willresult in a shifting by +20. When the“SAVE” key is depressed for a while,the set values will be saved. Pressingthe “MODE” key enables the next menuitem to be accessed without any savingaction.
4. Special Functions:When the “SELECT” key is depressedin the operating mode “ON” for a while,pumping action will be carried out for 60seconds.
1
4 3
2
Flanged progressive distributor: Control unit:
1)Explanation:
Delivery function: 24 V to Pin 1Stirring function: 24 V to Pin 1 and 2
Auxiliaries
Cable jack for electric connection:
913.404-65913.405-07
Connecting cable for externally moun-ted progressive distributor:
Pump aggregate GMG-B with reservoir1,5l; with level monitoring "C"; with fillingconnector "G"; pump element with 0,08cm³delivery stroke on the left side and 0,16cm³delivery stroke on the right side; with electriccontrol unit incl. distributor monitoring"B1 and A ; andprogressive distributor with 6 outlets andmonitoring
" 24VDC drive type "3 "
Purchase-designation:GMG-B.B / 1,5/ C / 0 / G / 08 / 16 / B1 / 3A/ P1
Pressure control valve at the pump element:
72
For operating pressure delimitation, pressure control valves can be connected to thepump element
Pressure control valve Purchase-no.:
250 bar 752.502-90
160 - 250 bar 752.502-67
7with opening pressure:
70 bar 752.502-65150 bar 752.502-62
Customised setting:50 - 160 bar 752.502-66
Auxiliary: (state purchase-no., please)
Should the function control of a mountedprogressive distributor with separate pur-chase-designation be connected to theGMG-B pump control unit, the variant "P "for the pump and the function control "R0"for the progressive distributor have to beselected.
When using variant "P ”, progressive distri-butors of the types VPB-B or VPB-G with upto 20 lubrication points can be mounted.
For the versions, please seeData sheet VPB-B: No. 0378Data sheet VPB-G: No. 0177
*
*
1)
2)
Progressive distributors P ... with functioncontrol can only be selected together withcontrol unit B1.
If the function control of a progressivedistributor is not to be connected to thepump control unit, then GMG-B with variant"PX" has to be selected with the progressivedistributor getting a separate purchasedesignation.
With level monitoring "F", grease cannotbe stirred.
Screwing kit Purchase-no.:
Ø 10 752.502-64
8for pipe:
Ø 6 752.502-68Ø 8 752.502-63
Time Mode / Pulse Mode:
Selection between time mode 01and pulse mode 02Default = 01
P1
Cycle Time h:1)
Cycle time setting in hours(0-255) Only in P1 = time modeDefault = 0
P2
Cycle Time
minutes(1-59) Only in P1 = time mode
1)min:
Cycle time setting in
Default = 2
P3
Pulses:
Pulse setting (1-999)Only in P1 = pulse modeDefault = 5
P4
Distributor Pulse:
Ends pumping action after elapse of pre-set pulse number ON = on, OFF = offDefault = OFF
P5
Distributor Pulse Number:
Distributor pulse setting (1-100)Only in P5 = distributor pulse ON modeDefault = -
P6
Delivery Time h:
Delivery time setting in hours(0-100) Only in P5 = distributor impulseOFF modeDefault = 0
P8
Delivery Time min:
Delivery time setting in minutes(1-59) Only in P5 = distributor pulse OFFDefault = 1
P9
Stirring:
Selection between “Stirring on” = ONand “Stirring off” = OFF (stirring time 1 min.)Default = OFF
P10
Off-duty Time for Stirring:
Off-duty Time setting in hours(1-100) Only in P10= Stirring ON
Cycle time = delivery time + off-duty time1)
Default = 1
P11
Distributor Monitoring:
Fault message release after 4 min. withoutdistributor signal. ON = on, OFF = offDefault = OFF
Pump aggregate GMG-B with reservoir1,5l; with level monitoring "C"; with fillingconnector "G"; pump element with 0,08cm³delivery stroke on the left side and 0,16cm³delivery stroke on the right side; with electriccontrol unit incl. distributor monitoring"B1 and A ; andprogressive distributor with 6 outlets andmonitoring
" 24VDC drive type "3 "
Purchase-designation:GMG-B.B / 1,5/ C / 0 / G / 08 / 16 / B1 / 3A/ P1
Pressure control valve at the pump element:
72
For operating pressure delimitation, pressure control valves can be connected to thepump element
Pressure control valve Purchase-no.:
250 bar 752.502-90
160 - 250 bar 752.502-67
7with opening pressure:
70 bar 752.502-65150 bar 752.502-62
Customised setting:50 - 160 bar 752.502-66
Auxiliary: (state purchase-no., please)
Should the function control of a mountedprogressive distributor with separate pur-chase-designation be connected to theGMG-B pump control unit, the variant "P "for the pump and the function control "R0"for the progressive distributor have to beselected.
When using variant "P ”, progressive distri-butors of the types VPB-B or VPB-G with upto 20 lubrication points can be mounted.
For the versions, please seeData sheet VPB-B: No. 0378Data sheet VPB-G: No. 0177
*
*
1)
2)
Progressive distributors P ... with functioncontrol can only be selected together withcontrol unit B1.
If the function control of a progressivedistributor is not to be connected to thepump control unit, then GMG-B with variant"PX" has to be selected with the progressivedistributor getting a separate purchasedesignation.
With level monitoring "F", grease cannotbe stirred.
Screwing kit Purchase-no.:
Ø 10 752.502-64
8for pipe:
Ø 6 752.502-68Ø 8 752.502-63
Time Mode / Pulse Mode:
Selection between time mode 01and pulse mode 02Default = 01
P1
Cycle Time h:1)
Cycle time setting in hours(0-255) Only in P1 = time modeDefault = 0
P2
Cycle Time
minutes(1-59) Only in P1 = time mode
1)min:
Cycle time setting in
Default = 2
P3
Pulses:
Pulse setting (1-999)Only in P1 = pulse modeDefault = 5
P4
Distributor Pulse:
Ends pumping action after elapse of pre-set pulse number ON = on, OFF = offDefault = OFF
P5
Distributor Pulse Number:
Distributor pulse setting (1-100)Only in P5 = distributor pulse ON modeDefault = -
P6
Delivery Time h:
Delivery time setting in hours(0-100) Only in P5 = distributor impulseOFF modeDefault = 0
P8
Delivery Time min:
Delivery time setting in minutes(1-59) Only in P5 = distributor pulse OFFDefault = 1
P9
Stirring:
Selection between “Stirring on” = ONand “Stirring off” = OFF (stirring time 1 min.)Default = OFF
P10
Off-duty Time for Stirring:
Off-duty Time setting in hours(1-100) Only in P10= Stirring ON
Cycle time = delivery time + off-duty time1)
Default = 1
P11
Distributor Monitoring:
Fault message release after 4 min. withoutdistributor signal. ON = on, OFF = offDefault = OFF
