Date post: | 16-Aug-2015 |
Category: |
Education |
Upload: | pace-it-at-edmonds-community-college |
View: | 23 times |
Download: | 4 times |
Network cabling III.
Page 2
Instructor, PACE-IT Program – Edmonds Community College
Areas of expertise Industry Certifications
PC Hardware
Network Administration
IT Project Management
Network Design
User Training
IT Troubleshooting
Qualifications Summary
Education
M.B.A., IT Management, Western Governor’s University
B.S., IT Security, Western Governor’s University
Entrepreneur, executive leader, and proven manger with 10+ years of experience turning complex issues into efficient and effective solutions.
Strengths include developing and mentoring diverse workforces, improving processes, analyzing business needs and creating the solutions required— with a focus on technology.
Brian K. Ferrill, M.B.A.
Page 3
Network cabling III.PACE-IT.
– Media converters.
– Cabling tools.
Page 4
Media converters.Network cabling III.
Page 5
It is not uncommon to be in a situation where a network contains more than one type of cabling.
This can lead to situations where there is a desire to connect different types of media together in order to make a cohesive network.
Thankfully, media converters are readily available. The issue mostly comes into play when joining fiber optic transmissions to a copper wire infrastructure.
Some common media converters will connect: SMF to Ethernet, MMF to Ethernet, SMF to MMF, and fiber to coaxial cabling.
Media converters.Network cabling III.
Page 6
Cabling tools.Network cabling III.
Page 7
Every technician should put some thought into the tools that are in his or her toolbox.
It is often said that you get what you pay for, and that is very true with tools. While a good technician can get away with buying the most inexpensive tools, spending a little more money for a better tool can often make a task easier and, ultimately, make the technician more efficient.
Cabling tools.Network cabling III.
Page 8
Cabling tools.Network cabling III.
– Crimpers.» Used to place cable ends on cables.
• They can be designed to work with a single type of cable or with multiple types.
– Wire strippers.» Used to remove the insulating cover on wires and
cables.• Many are designed to just cut through the insulation
without damaging the cable contained in the insulation.
• Some are also designed to cut all the way through the cable, so that excess cabling can be trimmed.
– The punchdown tool.» Used to secure cable wires into punchdown blocks.
Good ones will trim the ends at the same time.• In many cases, punchdown blocks are used to
terminate cable runs in a central location. Often, these blocks are on the backside of patch panels.
Page 9
Cabling tools.Network cabling III.
– The cable tester.» Used to test cables for common problems.
• Misconfiguration of the pinouts.• The cable standard used (T568A or T568B).• Shorts or breaks in the cable.• Some types of testers can also test for cable length
and quality (these are called cable certifiers).
– TDR (time-domain reflectometer).» A cable tester for copper cabling that can also
determine the length of a segment and the electrical characteristics of the cable.
» They can also tell where a break is in a segment.• More expensive than a standard cable tester.
– OTDR (optical time-domain reflectometer).
» Performs the same functions as a TDR, but used for fiber optic cabling.
Page 10
What was covered.Network cabling III.
Often, there will be a need to transition from one type of network cabling to another. Media converters make that transition possible, resulting in a cohesive network. Common media converters are: SMF to Ethernet, MMF to Ethernet, SMF to MMF, and fiber to coaxial cabling.
Topic
Media converters.
Summary
Each technician will need to determine the types and quality of tools in his or her toolbox. Common network cabling tools include: crimpers, strippers, punchdown tools, and cable testers. Not quite so common—or practical for most technicians—are the TDR and the OTDR.
Cabling tools.
Page 11
THANK YOU!
This workforce solution was 100 percent funded by a $3 million grant awarded by the U.S. Department of Labor's Employment and Training Administration. The solution was created by the grantee and does not necessarily reflect the official position of the U.S. Department of Labor. The Department of Labor makes no guarantees, warranties, or assurances of any kind, express or implied, with respect to such information, including any information on linked sites and including, but not limited to, accuracy of the information or its completeness, timeliness, usefulness, adequacy, continued availability or ownership. Funded by the Department of Labor, Employment and Training Administration, Grant #TC-23745-12-60-A-53.
PACE-IT is an equal opportunity employer/program and auxiliary aids and services are available upon request to individuals with disabilities. For those that are hearing impaired, a video phone is available at the Services for Students with Disabilities (SSD) office in Mountlake Terrace Hall 159. Check www.edcc.edu/ssd for office hours. Call 425.354.3113 on a video phone for more information about the PACE-IT program. For any additional special accommodations needed, call the SSD office at 425.640.1814. Edmonds Community College does not discriminate on the basis of race; color; religion; national origin; sex; disability; sexual orientation; age; citizenship, marital, or veteran status; or genetic information in its programs and activities.