PACKAGE ENGINEERING STANDARD I-20...• There are two standard label sizes; L6060 (60 x 60mm) and...

ISSUED: 08/16/18 STATUS: APPROVEDPKGENGF0024 REV30 https://ps.nafta.extra.fcagroup.com/sites/MPE/ PAGE: 1 of 16

PA G E O N E

PA C K A G E E N G I N E E R I N G S TA N D A R D I - 2 0

S U B J E C T: P a c k a g e L a b e l i n g I n s t r u c t i o n s

Page1. PACKAGE LABELING INSTRUCTIONS ........................................................... 2

2. LABEL ELEMENTS ....................................................................................... 2

3. LABEL SIZES ................................................................................................ 2

4. 3 OF 9 BARCODE ........................................................................................ 3

4.1 BAR CODE SYMBOLOGY ......................................................................... 3

4.2 CODE CONFIGURATION-SECONDARY PART NUMBER .............................. 3

4.3 CODE CONFIGURATION-CHRYSLER PART NUMBER.................................. 3

4.4 QUALITY ASSURANCE REQUIREMENT .................................................... 3

5. UNIT LABELS .............................................................................................. 4

5.1 NO PACKAGING REQUIRED PARTS ......................................................... 4

6. MINIMUM SALES QUANTITY LABEL ............................................................ 5

7. REMANUFACTURED AND RELABELED (RL) PACKAGING LABEL ..................... 6

8. RL13 LABELS ............................................................................................... 7

9. PERFORMANCE LABELS .............................................................................. 8

10. SECONDARY LABEL ..................................................................................... 9

11. DEPOSIT PART LABEL ................................................................................ 10

12. DO NOT DRAG OR THROW LABEL ............................................................. 10

13. HEAVY PART LABEL ................................................................................... 11

14. BRAKE UNIT CARTON AND KIT LABELING ................................................. 12

15. HAZARDOUS MATERIAL AND ENVIRONMENTAL LABELING REQUIREMENTS .......................................... 13

16. INTERSTATE MERCURY EDUCATION & REDUCTION CLEARINGHOUSE (IMERC) STATE MERCURY-ADDED LABELING GUIDELINES ......................... 13

16.1 MERCURY PRODUCT AND PACKAGE LABELS ....................................... 14

16.2 EXAMPLES OF ACCEPTABLE MERCURY PHRASES ................................. 14

17. IMPRINTING ON CARTONS AND POLY BAGS ............................................. 16

18. GENERAL INFORMATION .......................................................................... 16


1. LABELING INSTRUCTIONS • This Package Engineering Standard establishes a standardized format for identifying parts and unit

packaged product for Mopar.• These labels are required on all parts packaged for Mopar with the exception of packages that

incorporate the label into the design.• All Mopar “L-Series” unit labels must be purchased from the single source supplier RR Donnelley.

Direct all requests to [email protected].

1.1 No Packaging Required Parts

• If parts do not require unitized packaging, they must be identified with a “L-Series” label and follow the outlined labeling requirements.

• Acceptable Methods:

• Direct application - The label must securely adhere to the surface of the part.

• Envelopes, bags, pouches, cartons, etc. - Items requiring identification which are so small that they cannot be identified in any other manner, may be bulk / masterpacked in cartons, bags, envelopes, pouches, cohesive paper or heat sealable material. The part number and quantity shipped must be placed on the shipping container (AIAG label).

• Bundling - Bundling in lieu of a bulk container is only permitted when the quantity ordered is less than one half the full shipping container quantity for a given part number or when the part exceeds ninety-two (92) inches in length. Bundles must not exceed fifty (50) pounds.

• Wire Tag - A tag attached with a wire may be used for “L-Series” label application. Tag material can be: metal, plastic, cloth, or paper (manila index stock). Metal tags must have corners blunted.

• Exemptions - Parts shipping to 03116 to be e-coated are exempt from this requirement. The part number and quantity shipped MUST be placed on the shipping container i.e. rack, basket, box (AIAG shipping label). If more than one part is to be shipped in the same container, the parts must be separated and at least one part is to be identified with the individual part number (NO directly applied labels allowed). The methods that are acceptable are embossing, ink stamping, or molding as applicable. There should be no more than 3 different part numbers per container, metal tub, or rack. All parts must be accessible from the open container (no layering).

• Application: The application selected must not have a deleterious effect on the life and utility of the item.

• “Flag Tape” Method - Wrap identification tape strip around part and adhere label to itself.

• Each shipping container must be clearly marked with the quantity contained, part number, barcode, supplier code, and date code.

2. LABEL ELEMENTS• Labels come preprinted with Mopar Racing Stripe logo and Federal Mandated Content Statement.• Imprinting must be black.

3. LABEL SIZES • There are two standard label sizes; L6060 (60 x 60mm) and L6045 (60 x 45mm).• Selection of label size should be in proportion to the size of the package. • Use L-21 for decorative cartons with Mopar graphics.


4.1 Barcode Symbology • Barcode shall conform to the Barcode Symbology Standard for 3 of 9 Barcodes published by the Automotive

Industry Action Group (AIAG-B10). Document available on Mopar Package Engineering website. 4.2 Code Configuration - Secondary Part Number

• The four (4) characters ($, /, +, % ) or spaces shall not be used on the 3 of 9 symbology of Mopar labels. • The barcode should identify the part number and quantity only. • Secondary part numbers are always 10 digits/characters and quantity is always 3 digits. (i.e. 1=001)• Be sure the correct letters and numbers are consistently used, for example using the

number “0” instead of the letter “O” where applicable.4.3 Code Configuration - FCA US Part Number

• The four (4) characters ($, /, +, % ) or spaces shall not be used on the 3 of 9 symbology of Mopar labels. • The barcode should identify the part number only. • Mopar part numbers are always 8 or 10 digits/characters. • Be sure the correct letters and numbers are consistently used, for example using the

number “0” instead of the letter “O” where applicable.4.4 Quality Assurance Requirements

• It is the responsibility of the supplier to provide barcode labels that meet these specifications. • Equipment must be available to verify that barcode symbols meet these requirements. • The use of statistical process control techniques to minimize printing variability is recommended. • When scanned, top barcode must read the part number and quantity, and bottom barcode

must read part number only.• The barcode must scan within the Mopar distribution and dealership network.• Nonconformance to these requirements will result in rework charges.

3 OF 9 BARCODE MINIMUM QUARTER INCH VOID LEFT AND

RIGHT SIDE

MINIMUM SIXTEENTH INCH VOID TOP AND

RIGHT BOTTOM

.25”.0625”

.0625”

.25”

4. 3 OF 9 BARCODE• The 3 of 9 barcode is used for scanning part numbers within the Mopar distribution and dealership network. • The 3 of 9 barcode has an area of 1/4“ void, side and side and 1/16” top and bottom.


1

2

3456

789

L6060

2.36

2” (6

0 m

m)

2.362” (60 mm)

Helvetica Med. Cond. 7 pt.


Barcode height 0.35”/8 mm




Part number Helvetica Med. 14 pt. Quantity Per Package Helvetica Light 14 pt.





Barcode height 0.25”/6.3 mm


Helvetica Med. Cond. 7 pt.1

23456789

L6045

1.77

2” (4

5 m

m)

1. Branding: Pre-printed on label.2. Use Before: If product has a shelf life. Print only if needed. Format is Year(YYYY)/Month(MM)/Day(DD)3. Secondary Part Number Bar Code: Secondary part number information required on L-Series labels will be found

via EDI data transmitted to suppliers. FCA Italy part number 10 digits and quantity per package 3 digits (13 digits total). The bar code must read without any spaces.

• The part number 82377992 (8 digits) becomes 008237992 (10 digits) and qty. per package 1 becomes 001 (3 digits). • The bar-code will be: 0082377992001 (13 digits).

4. Secondary Part Number and Quantity per Package: • Part number displayed as 10 digit part number. • Quantity per package is always equal to 1• Quantity format is “- 001”

5. Made In: Parts shipped to any Mopar facility are required to be marked with the country of origin according to Part 134 of Title 19 Code of Federal Regulations (CFR). Country of origin determination should be made according to Part 102 of Title 19 CFR.

6. PKG: Format is Year(YYYY)/Month(MM)/Day(DD) Supplier: Ship from supplier code and location code, if applicable. (example 12345A) PSC: Packaging Source Code. Only applicable to third party packagers.

7. FCA US Part Number Barcode: (3 of 9 barcode): 8 or 10 digit part number. The barcode must read without any spaces.• Example: 00000000AA (10 digit) or 00000000 (8 digit)• Reference 3 of 9 barcode for conformance standards.

8. FCA US Part Number and Quantity Per Package: • Part number displayed as 8 or 10 digit part number. • Part number format is “4 4 2” (10 digit ) or “4 4” (8 digit). • Quantity per package is always equal to 1• Quantity format is “- 001”

9. Label Number and Federally Mandated Statement: Pre-printed on label. See following sections for GT and MSQ labeling information.

5. UNIT LABELS - One Part Per Pack or Part


1. Branding: Pre-printed on label.2. Use Before: If product has a shelf life. Print only if needed. Format is Year(YYYY)/Month(MM)/Day(DD).3. Secondary Part Number Bar Code: Secondary part number information required on L-Series labels will be found



4. Secondary Part Number and Quantity per Package: • Part number displayed as 10 digit part number. • Quantity per package is always greater than 1• Quantity format is “- 010”



7. FCA US Part Number Barcode: (3 of 9 barcode): 8 or 10 digit part number. The barcode must read without any spaces.• Example: 00000000AA (10 digit) or 00000000 (8 digit).• Reference 3 of 9 barcode for conformance standards.

8. FCA US Part Number and Quantity Per Package: • Part number displayed as 8 or 10 digit part number. • Part number format is “4 4 2” (10 digit ) or “4 4” (8 digit). • Quantity per package is always greater than 1• Quantity format is “- 010”

9. Label Number and Federally Mandated Statement: Pre-printed on label.✱ MSQ: Supplier must print on label. The MSQ black box size: 0.5803” x 0.3125” / 15 x 8 mm. MSQ letters:

Helvetica Black Cond. 28.7pt. The box is placed on the label .0119”(3 mm) from the left edge of the label and .1.2” (30 mm) from the top edge of the label. For parts that have a minimum sales quantity (MSQ).

L6060 MSQ

2.36

2” (6

0 m

m)

✱

6. MINIMUM SALES QUANTITY LABEL• Minimum Sales Quantity (MSQ) labels are to be used on packages containing parts with minimum sales

quantity requirements. • The MSQ labels will have the letters MSQ in a black box in the upper left corner. • These parts will contain more than one piece in each unit container and are considered to be an MSQ. • Only Mopar will determine and dictate MSQ requirements.

Helvetica Med. Cond. 7 pt.Helvetica Med. Cond. 7 pt.





2.362” (60 mm)

1

2

3456

789



RAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDADGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERL=6060

Genuine Parts & Accessories™

®

R000 0000 AA – 001

5 5 5 5 5 5 5 5 5 5 – 0 0 1

PKG: YYYY/MM/DD Suppl ier PSC

Remanufactured In (Country) Serial Number

L6060 RL2.

362”

(60

mm

)

✱

7. REMANUFACTURED AND RELABELED (RL) PACKAGING LABEL• Packaging for Relabeled (RL) and remanufactured parts requires the standard Mopar label as illustrated below.

1. Branding: Pre-printed on label. 2. Secondary Part Number Bar Code (3 of 9): 10 digit part number and 3 digit quantity (13 digits total). The bar

code must read without any spaces.• Example 5555555555 - 001 would read 5555555555001• Reference 3 of 9 barcode for conformance standards.

3. Secondary Part Number Bar Code: Secondary part number information required on L-Series labels will be found via EDI data transmitted to suppliers. FCA Italy part number 10 digits and quantity per package 3 digits (13 digits total). The bar code must read without any spaces.

• The part number 82377992 (8 digits) becomes 0082377992 (10 digits) and qty. per package 1 becomes 001 (3 digits). • The bar code will be 0082377992001 (13 digits).

4. Made In or Remanufactured In: Parts shipped to any Mopar facility are required to be marked with the country of origin according to Part 134 of Title 19 Code of Federal Regulations (CFR). Country of origin determination should be made according to Part 102 of Title 19 CFR.



7. FCA US Part Number and Quantity Per Package: • Part number displayed as 8 or 10 digit part number. • Part number Format is “4 4 2” (10 digit ) or “4 4” (8 digit). • Quantity per package is always equal to 1• Quantity format is “- 001”

8. Label Number and Federally Mandated Statement: Pre-printed on label.✱ Serial Number: Serial Number of part number






1

2345

678

2.362” (60 mm)


3”

1.125”

0000000000

00000000000000 0000 AA - 001

0000000000

00000000000000 0000 AA - 001

0000000000

00000000000000 0000 AA - 001

Helvetica Med. 18pt.

Helvetica Med. Cond 13pt.

RL13 Labels

1. Required on Remanufactured Powertrain and RL Powertrain Assemblies• Directly below the standard Mopar label, suppliers must apply three double stick RL13 labels on each

cylinder head, engine and transmission package. • This is only required on remanufactured powertrain and RL powertrain assemblies - see PS-12658 for

more information on completing the RL13 label. • The labels are used to adhere to the warranty registration required for powertrain parts, one for the

customer, dealer and Mopar records. (Example shown is not drawn to size.)• FCA US Part Number Barcode: (3 of 9 barcode): 8 or 10 digit part number. The barcode must read with

out any spaces. • Example: 00000000AA (10 digit) or 00000000 (8 digit).• Add Serial Number Barcode: (3 of 9 barcode) The serial number barcode must read without any spaces. • Example: 00000000• For part marking information refer to PS-12658

2. FCA US Part Number and Quantity Per Package: • Part number displayed as 8 or 10 digit part number. • Part number Format is “4 4 2” (10 digit ) or “4 4” (8 digit). • Quantity per package is always equal to 1• Quantity format is “- 001”

3. Add Serial Number Barcode: (3 of 9 barcode) The serial number barcode must read without any spaces.• Example: 00000000

8. RL13 LABELS


9. PERFORMANCE LABELS - One Part Per Pack• Packaging for performance parts requires the Mopar Performance Parts label as illustrated below.

RAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDADGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERL=6060PP

®

0000 0000 AA – 001

5 5 5 5 5 5 5 5 5 5 – 0 0 1


Made In (Country)

USE BEFORE: YYYY/MM/DD

2.36

2” (6

0 m

m)




4. Secondary Part Number and Quantity per Package: • Part number displayed as 8 or 10 digit part number. • Quantity per package is always equal to 1• Quantity format is “- 001”




8. FCA US Part Number and Quantity Per Package: • Part number displayed as 8 or 10 digit part number. • Part number format is “4 4 2” (10 digit ) or “4 4” (8 digit). • Quantity per package is always equal to 1• Quantity format is “- 010”

9. Label Number: Pre-printed on label.

L6060 Performance

1

2

3456

789






2.362” (60 mm)



Made In (Country)

USE BEFORE: YYYY/MM/DD

0000 0000 AA – 012

5 5 5 5 5 5 5 5 5 5 – 012

Suppl ier PSC

RAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDADGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERL=6060GT


®

PKG: YYYY/MM/DD




4. Secondary Part Number and Quantity per Package: • Part number displayed as 10 digit part number. • Quantity per package is always greater than 1• Quantity format is “- 001”




8. FCA US Part Number and Quantity Per Package: • Part number displayed as 8 or 10 digit part number. • Part number format is “4 4 2” (10 digit ) or “4 4” (8 digit). • Quantity per package is always greater than 1• Quantity format is “- 010”

9. Label Number and Federally Mandated Statement: Pre-printed on label

✱Green Triangle: Pre-printed on label. Required for all master packs.

L6060 GT2.

362”

(60

mm

)

✱

10. SECONDARY LABEL - Master Pack of Multiple Unit Packs• The Green Triangle label is used when unit containers are master packed.






2.362” (60 mm)

1

2

3

45

6

789



1. Branding: Pre-printed on label2. Use Before: If product has a shelf life. Format is Year(YYYY)/Month(MM)/Day(DD)3. Made In: Parts shipped to any Mopar facility are required to be marked with the country of origin

according to Part 134 of Title 19 Code of Federal Regulations (CFR). Country of origin determination should be made according to Part 102 of Title 19 CFR.

4. PKG: Format is Year(YYYY)/Month(MM)/Day(DD) Supplier: Ship from location code PSC: Packaging Source Code. Only applicable to third party packagers.

5. Barcode (3 of 9 barcode): 8 or 10 digit part number. The barcode must read without any spaces.

• Example: 00000000AA (10 digit) or 00000000 (8 digit)• Reference AIAG-B10 for conformance to standard barcode.

6. Part Number and Quantity Per Package: • Part number displayed as 8 or 10 digit part number. • Part Number Format is “4 4 2” (10 digit ) or “4 4” (8 digit). • Quantity per package is always equal to 1• Quantity Format is “- 001”

7. Label Number and Federally Mandated Statement: Pre-printed on label✱. MSQ: Supplier must print on label. A black box the size of .04375”x.08125”/ 21.5 x 10.7mm.

MSQ letters must be legible. For parts that have an minimum sales quantity (MSQ).

11. DEPOSIT PART LABEL• The deposit part label is required for parts where Mopar has added core/deposit charges. • These charges are reimbursed to an eligible Dealer as a credit when the replaced

component is returned to its facing Parts Distribution Center (PDC) following the Global Core Return Process.

• The required label is shown below with the green background and white letters. • The standard label size is 3.0” x 3.0”. “Deposit Part” must be translated into all NAFTA

languages (Spanish and French). • If other destinations are known, the proper translations must be shown. • Deposit label placement is next to Mopar Packaging Label.• All “DEPOSIT PART” labels must be purchased from the single source supplier RR

Donnelley. Direct all requests to [email protected].

12. DO NOT DRAG OR THROW LABEL• The “DO NOT DRAG OR THROW” label is required for all scrim wrapped fascias.• The required label is shown below with the black background and white letters.• The standard label size is 5.0”x5.0” . “DO NOT DRAG OR THROW” must be translated into

all NAFTA languages (Spanish and French).• If other destinations are known, the proper translations must be shown.• The “DO NOT DRAG OR THROW” label placement is above the deposit part label (if

applicable) - if not applicable placement is above the Mopar L-6060 label.• All “DO NOT DRAG OR THROW” labels must be purchased from the single source supplier

RR Donnelley. Direct all requests to [email protected].

(PIEZA DE PAGO DE DEPÓSITO)

(PIÈCES CONTRE DÉPÔT)

DEPOSITPART

Helvetica Bold Condensed 65pt.

Helvetica Bold Condensed 25pt.

100% K (Black)


3.00

3.00

3.00

3.00

Red PMS 186

13. HEAVY PART LABEL• The heavy part label is required for packages weighing 30 lbs. / 13 kg or more that do not

have a base pallet built into the overall package. • This includes unit packages and master packages but excludes packages that can only be

handled by machinery (i.e. Engine or Transmission packs). • The preferred label is shown below on left. Black is acceptable if preprinted on carton. • The standard label size is 3.0” x 3.0”. • A larger label may be used on oversized cartons and should be proportionate to the

carton face it is being applied to.

Preferred


14. BRAKE UNIT CARTON AND KIT LABELING• Brake unit cartons must contain a Prop 65 Warning Label, and L-Series Label.• All labels and placement of labels are shown below. (Examples shown are not to size)• Prop 65 label 1” x 3”.

• Mopar requires all packaging containing brake friction materials to abide by the California & Washington’s Brake Friction Material legislation laws as well as Washington’s Better Brake Rule by marking the parts with a:1. Letter on Edge Code of product, and2. LeafMark trademarks on packaging

For additional information and requirements, see:http://www.dtsc.ca.gov/PollutionPrevention/BrakePads.cfm https://ecology.wa.gov/Waste-Toxics/Reducing-toxic-chemicals/Better-Brakes-law

MISE EN GARDE : Certains composants du véhicule contiennent ou émettent des substances chimiques qui, selon l'État de la Californie, peuvent causer le cancer, des anomalies congénitales et des problèmes d'ordre génital.

WARNING: Cancer and Reproductive Harm AVERTISSEMENT : Cancer et Troubles de l'appareil reproducteur • ADVERTENCIA: Cáncer y Daño Reproductivo – www.P65Warnings.ca.gov.

RAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDADGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERJEEPRAMDODGECHRYSLERL=6060


®

0000 0000 AA – 001

5 5 5 5 5 5 5 5 5 5 – 0 0 1


Made In (Country)

L6060 label.


16. Mercury-Added Labeling Guidelines for Interstate Mercury Education & Reduction Clearinghouse (IMERC) State and Canadian Environmental Protection Act, 1999 – Products Containing Mercury Regulation SOR/2014-254 NOTE: Only for products where mercury (Hg) and/or mercury compounds have been intentionally added. Product examples include, but are not limited to: Headlamps, HID Bulbs, Entertainment and Navigational Displays

For more information on IMERC labeling: http://www.newmoa.org/prevention/mercury/imerc/labelinginfo.cfmFor more information on Canada’s labeling: http://www.ec.gc.ca/mercure-mercury/

• This labeling requirement applies to any product that contains mercury, a mercury compound, or a component containing mercury if the mercury is intentionally added to the product (or component) for any reason.

15. HAZARDOUS MATERIAL AND ENVIRONMENTAL LABELING REQUIREMENTS It is the supplier ’s responsibility to ensure that all hazardous and/or consumer labeling

requirements are in compliance with the DOT and OSHA regulations. MSDS and full formula disclosure must be submitted to FCA US Corporate Industrial Hygiene prior to first shipment. Send or fax documents to :

FCA US Corporate Industrial Hygiene & Toxicology Department Attn: MSDS Coordinator CIMS 482-00-41 800 Chrysler Drive Auburn Hills, MI 48326 FAX: (248) 512-3339

Parts containing material that may be regulated by OSHA, Federal and/or State regulations must comply with all regulations, (i.e. asbestos, silica quartz, mercury, etc.)

continued on next page

16.1 Product And Package Labels: The Product and Package label must meet the following minimum requirements:

• Must be visible, printed in English, French, and Spanish using 10 point font or larger and characters that are at least 3 mm in height.

• Must be sufficiently durable to remain legible throughout the life of the product; such as mounted, engraved, molded, embossed, impressed, or in a colour that contrasts with the label’s background or the colour of the product.

• Enclosed by a border;

• States that the product “contains mercury” and cannot be placed in trash – it must be recycled or disposed of as a hazardous waste.

• A statement where to find information regarding safe handling procedures and the measures to be taken in case of accidental breakage, the address of a website where that information is available, or contact information for a person who can provide that information.


• A statement where to find information regarding options available for the disposal and recycling of the product in accordance with the laws of the jurisdiction where the disposal or recycling is to take place, the address of a website where that information is available, or contact information for a person who can provide that information.

• If the product incorporates a mercury-added component that is not visibly labeled in accordance with this standard, the label on the larger product must clearly identify the internal component.

• If the product is sold in packaging that obscures the label, the packaging must also be labeled as described above.

• Includes the symbol Hg in a circle for lamps.

• If the product is offered for sale by catalog, telephone, or internet such that the label on the product or packaging is not visible at the time of purchase, the consumer must be made aware prior-to-purchase that there is intentionally-added mercury in the product by placing a label or other information provided in sales literature, webpages, etc

• If the product is too small to accommodate the information, the information must be indicated

1. In a readily visible location on the product’s package; or

2. If there is no package or if the package is too small to accommodate the information, in a notice attached to the product or in a manual that accompanies the product. The notice or manual may provide the address of a website where the relevant information is available and must be provided in English, French, and Spanish.

16.2 Examples Of Acceptable Mercury Phrases:

“This product contains Mercury. Do not put in trash. Recycle or Dispose as Hazardous Waste.”

“Contains Mercury, Don’t Put In Trash. Recycle or Dispose as Hazardous Waste”

“Contains Mercury, Dispose According to Local, State or Federal Laws”

“Contains Mercury, Dispose of Properly”

“The lamp in this product contains mercury dispose according to local, state, or federal law”

“The bulb in this product contains mercury. Don’t Put In Trash. Recycle or Dispose as Hazardous Waste.”

“For information on safe handling procedures, measures to be taken in case of accidental breakage and options available for disposal and recycling call [insert phone number] (or) visit [insert website]”

“Not regulated by DOT (Department of Transportation).”

continued on next page


• Symbols and images may be used but, must be accompanied by acceptable phrases shown above

• If the product does not have a retail package – i.e., the shipping box is the only outer package.

• The shipping box must be labeled notifying the consumer that the product contains mercury.

• The following labels have been approved by UPS (United Parcel Service) to be placed on shipping boxes in this situation.

• Size of the label is not mandated, however, the font must be 10 point or larger and characters must be no less than 3 mm in height.


17. IMPRINTING ON CARTONS AND POLY BAGS• All imprinting must be legible, centered, and machine printed or stamped.• All imprinters must follow requirements in this document.• Imprint should not cover the Mopar logo or the Federally Mandated

Content Statement.• For size determination reference Section 3.• Mopar graphic containers may be imprinted as long as the labeling elements are not

compromised. The label information must be imprinted on a solid contrasting background.• Folding cartons — Label information must be printed or applied on the plain white end

panel or top flap.• Envelopes — These packaging containers must be labeled with a Mopar label or imprinted with

the proper identification. Label placement must be below the Mopar logo when present. • Poly Bags — Reference Package Engineering Standard P-16 for poly bag imprinting requirements.

18. GENERAL INFORMATION• Labels must be placed on end panel for corrugated containers or on the plain white end

panel or flap for graphic containers.• Supplier logos, artwork, addresses, etc., are NOT permitted on any Mopar labels,

individual containers or master packs.• Mopar retail graphic packaging requires that label information be printed directly on the

container or an L-21 label must be applied.• Non-graphic packaging must include an applied L-Series label.• SSD (Supplier Ship Direct) products are subject to the same requirements as the regular

stock parts program, i.e., label format, package submission and approval.• Deviations from this standard are not permitted without prior written approval by the

Mopar Package Engineering Department of FCA US LLC.• Mopar Graphic Packaging — Contact Buffalo Brothers Studios East, Inc.;

[email protected] or [email protected]• Packaging Approval — Each supplier is responsible for submitting their packaging proposal

to the Mopar Package Engineering Department for approval prior to shipping. Please contact your Package Engineer.

Date post:	27-Apr-2020
Category:	Documents
Upload:	others
View:	3 times
Download:	0 times

PACKAGE ENGINEERING STANDARD I-20...• There are two standard label sizes; L6060 (60 x 60mm) and...

Documents