StateMSP To UpdateVHA/Huawei to updateMSP to update Post acceptanceSite/Cell Information SegmentReason SegmentRecommendation SegmentPerformance Monitoring/ Observation SegmentGeneral SegmentApprovalPost Status checks Site/Cell Information Segment
Dinesh Dindukurthi: Dinesh Dindukurthi:Exp:NSW_ACT 00001Date of Implementation/Recommendation
Dinesh Dindukurthi: Dinesh Dindukurthi:Date Format

DD-MM-YEARWeek Number
Dinesh Dindukurthi: Dinesh Dindukurthi:Week Number will be displayed as soon as you insert Date.RNCSite ID for 2G & 3GSite NameCell IDCell NameHow the issue was identified
Dinesh Dindukurthi: Dinesh Dindukurthi:Pickup from the drop down menu, how did you identify the site/cell for Optimization activityWhat is impacted
Dinesh Dindukurthi: Dinesh Dindukurthi:

Drop down provided the Service/KPI/Drive test services was degraded/ impacted.

If 2 or more services impacted, pick up the one which is more significant issue/heavily degradedWhat is the Root Cause of the issue
Dinesh Dindukurthi: Dinesh Dindukurthi:

What is the root cause of the occurance of the issueParamater Name as shown in M2000Target Neighbour Cell (CIOOffset-PSC) for Paramater Change / Neighbour cell Addition/DeletionCurrent Paramater SettingsProposed Parameter Settings/ Proposed Neighbour addition/DeletionPre optimization Performance checkPost optimization Performance checkPerformance ImpactTT / CR No.RF Engineer NameComments/ObservationVHA Review/ApprovalHuawei Review/ApprovalHuawei/VHA CommentsStatus of RecommendationsDate of ChangeMSP CommentsQLD 006641/4/1301-2013GTBH2404618404618_Iveragh_146181404618_Iveragh_MX_G09A_1KPI DegradationRetainability ADD G2GNCELL404626_MountHopeful_MX_G09A_1Performance ImprovementImprovement in KPIGopiHigh number of TA drops, downtilt proposed , in the mean time add these 2G neighbour to improve KPI,remember its a split cell.ApprovedDone, added both waysImplemented1/18/13OkQLD 006651/4/1301-2013GTBH2404618404618_Iveragh_146181404618_Iveragh_MX_G09A_1KPI DegradationRetainability ADD G2GNCELL404512_Gladstone_MX_G09A_2Performance ImprovementImprovement in KPIGopiHigh number of TA drops, downtilt proposed , in the mean time add these 2G neighbour to improve KPI,remember its a split cell.ApprovedDone, added both waysImplemented1/18/13OkQLD 006661/4/1301-2013GTBH2404618404618_Iveragh_146181404618_Iveragh_MX_G09A_1KPI DegradationRetainability ADD G2GNCELL404616_Toonboro_MX_G09A_0Performance ImprovementImprovement in KPIGopiHigh number of TA drops, downtilt proposed , in the mean time add these 2G neighbour to improve KPI,remember its a split cell.ApprovedDone, added both waysImplemented1/18/13OkQLD 006671/4/1301-2013GTBH2404618404618_Iveragh_146181404618_Iveragh_MX_G09A_1KPI DegradationRetainability ADD G2GNCELL404625_Raglan_MX_G09A_0Performance ImprovementImprovement in KPIGopiHigh number of TA drops, downtilt proposed , in the mean time add these 2G neighbour to improve KPI,remember its a split cell.ApprovedDone, added both waysImplemented1/18/13OkQLD 006681/4/1301-2013GTRH2404348404348_LittleMountain55403404348_LittleMountain_MV_U08A_3KPI DegradationAccessibilityMAXTXPower46047860W power license is required( Dl power congestion)Performance ImprovementImprovement in KPISallyApprovedNodeB not licensed for 478. H/w wise this is possible. Also, need official email from VHA to increase the maxpwr to 478Implemented2/24/13okQLD 006751/10/1302-2013GTRH2404357404357_Warana_253696404357_Warana_MV_U21B_3KPI DegradationAccessibilityIdleQoffset2sn0-2DL power congestion, MaxTx Power/CPICH= 46/36 SallyPushing some traffic to other carrier.RejectedI checked the most recent stats for this both daily and busy hour and the accessbility is above 98%. Also, 404357_Warana_MV_U21A_3 is already carrying more traffic than 404357_Warana_MV_U21B_3.RejectedOk, LeaveQLD 006761/11/1302-2013BERH1404328404328_Noosa_357723404328_Noosa_MV_U08A_3Trigger for OptiCapacityMAXTXPower460478High RRC Rejection due to DLPower Congestion. 60W power license is requiredDhirenRejectedNodeB not licensed for 478. H/w wise this is possible. Also, need official email from VHA to increase the maxpwr to 478. But long term solution would be 2nd U850 carrier as it is trigerring on Code congestion as well. Also, downtilting would help as 20% of the traffic is beyond 6km based from propagation delay stats.Rejected2nd U850 carrier not possible as VHA doesn't have license for E2 in North Brisbane(Sunshine Coast) area. Rejection due to Downlink Power congestion is zero now. Ok to leave as is.QLD 006771/11/1302-2013BERH1401435401435_TownsvilleMSC_255106401435_TownsvilleMSC_MX_U21A_3Trigger for OptiCapacityMAXTXPower460478High RRC Rejection due to DLPower Congestion. 60W power license is requiredPerformance ImprovementImprovement in KPIDhirenApprovedOk, but long term solution would be U850 carrier as it is trigerring high on Code congestion as well. Implemented1/30/13QLD 006801/18/1303-2013GTRH2404431404431_Toombul_255559404431_Toombul_MV_U08B_3KPI DegradationAccessibilityCPICH360340HS throughput degraded after CPICH increased on 5/11/2012 on U08B_3. This is a temp change and will reverted onces proposed physical change is completed for this sector.Performance ImprovementImprovement in KPIDhirenApprovedokImplemented2/24/13okQLD 006811/18/1303-2013BERH3409315409315_Beenleigh_253154409315_Beenleigh_MO_U21B_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-14-12Remote site picking traffic from large TP. Encouraging timely compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 2%. Number of drops approx 100/dayQLD 006821/18/1303-2013BERH3409315409315_Beenleigh_253156409315_Beenleigh_MO_U21B_3KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-14-12Remote site picking traffic from large TP. Encouraging timely compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in DCR around 29th Jan from 3% to approx 1% in feb. Number of drops reduced from 30/day to 5/day. Ok to leaveQLD 006831/18/1303-2013BERH3409315409315_Beenleigh_253157409315_Beenleigh_MO_U21A_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-14-12Remote site picking traffic from large TP. Encouraging timely compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 1.25%, drops about 60/day.QLD 006841/18/1303-2013BERH3409315409315_Beenleigh_253159409315_Beenleigh_MO_U21A_3KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-14-12Remote site picking traffic from large TPs and droping. Encouraging timely compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in drops from 1.5 in jan to 0.75% approx. Reduction in drops from around 30 /day to 15/day. Okay to leaveQLD 006851/18/1303-2013BERH3404302404302_Beenleigh_255681404302_Beenleigh_MV_U08A_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-15-13Remote site picking traffic from large TP. Encouraging timely compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 006861/18/1303-2013BERH3404302404302_Beenleigh_255683404302_Beenleigh_MV_U08A_3KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-15-13Remote site picking traffic from large TP. Encouraging timely compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 006871/18/1303-2013BERH3404302404302_Beenleigh_255687404302_Beenleigh_MV_U08B_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-14-12Remote site picking traffic from large TP. Encouraging timely compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 006881/18/1303-2013BERH3404302404302_Beenleigh_255689404302_Beenleigh_MV_U08B_3KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-14-12Remote site picking traffic from large TP. Encouraging timely compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 006891/18/1303-2013BERH3409315409315_Beenleigh_253154409315_Beenleigh_MO_U21B_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-11-10Remote site picking traffic from large TP. Prolonging compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 2%. Number of drops approx 100/dayQLD 006901/18/1303-2013BERH3409315409315_Beenleigh_253156409315_Beenleigh_MO_U21B_3KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-11-10Remote site picking traffic from large TP. Prolonging compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in DCR around 29th Jan from 3% to approx 1% in feb. Number of drops reduced from 30/day to 5/day. Ok to leaveQLD 006911/18/1303-2013BERH3409315409315_Beenleigh_253157409315_Beenleigh_MO_U21A_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-11-10Remote site picking traffic from large TP. Prolonging compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 1.25%, drops about 60/day.QLD 006921/18/1303-2013BERH3409315409315_Beenleigh_253159409315_Beenleigh_MO_U21A_3KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-11-10Remote site picking traffic from large TP. Prolonging compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in drops from 1.5 in jan to 0.75% approx. Reduction in drops from around 30 /day to 15/day. Okay to leaveQLD 006931/18/1303-2013BERH3404302404302_Beenleigh_255681404302_Beenleigh_MV_U08A_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-12-11Remote site picking traffic from large TP. Prolonging compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 006941/18/1303-2013BERH3404302404302_Beenleigh_255683404302_Beenleigh_MV_U08A_3KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-12-11Remote site picking traffic from large TP. Prolonging compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 006951/18/1303-2013BERH3404302404302_Beenleigh_255687404302_Beenleigh_MV_U08B_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-12-11Remote site picking traffic from large TP. Prolonging compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 006961/18/1303-2013BERH3404302404302_Beenleigh_255689404302_Beenleigh_MV_U08B_3KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-12-11Remote site picking traffic from large TP. Prolonging compressed modeHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 006971/18/1303-2013BERH3409315409315_Beenleigh_253154409315_Beenleigh_MO_U21B_1KPI DegradationRetainabilitySSEARCHRAT13Encouraging IRAT measurements earlyHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 2%. Number of drops approx 100/dayQLD 006981/18/1303-2013BERH3409315409315_Beenleigh_253156409315_Beenleigh_MO_U21B_3KPI DegradationRetainabilitySSEARCHRAT13Encouraging IRAT measurements earlyHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in DCR around 29th Jan from 3% to approx 1% in feb. Number of drops reduced from 30/day to 5/day. Ok to leaveQLD 006991/18/1303-2013BERH3409315409315_Beenleigh_253157409315_Beenleigh_MO_U21A_1KPI DegradationRetainabilitySSEARCHRAT13Encouraging IRAT measurements earlyHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 1.25%, drops about 60/day.QLD 007001/18/1303-2013BERH3409315409315_Beenleigh_253159409315_Beenleigh_MO_U21A_3KPI DegradationRetainabilitySSEARCHRAT13Encouraging IRAT measurements earlyHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in drops from 1.5 in jan to 0.75% approx. Reduction in drops from around 30 /day to 15/day. Okay to leaveQLD 007011/18/1303-2013BERH3404302404302_Beenleigh_255681404302_Beenleigh_MV_U08A_1KPI DegradationRetainabilitySSEARCHRAT13Encouraging IRAT measurements earlyHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007021/18/1303-2013BERH3404302404302_Beenleigh_255683404302_Beenleigh_MV_U08A_3KPI DegradationRetainabilitySSEARCHRAT13Encouraging IRAT measurements earlyHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007031/18/1303-2013BERH3404302404302_Beenleigh_255687404302_Beenleigh_MV_U08B_1KPI DegradationRetainabilitySSEARCHRAT01Encouraging IRAT measurements earlyHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007041/18/1303-2013BERH3404302404302_Beenleigh_255689404302_Beenleigh_MV_U08B_3KPI DegradationRetainabilitySSEARCHRAT01Encouraging IRAT measurements earlyHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007051/18/1303-2013GTBH1404302404302_Beenleigh_1404302_Beenleigh_MO_G09A_1KPI DegradationRetainabilityFDDQMIN65Retaining border traffic(likely to be dropped) on 2G moreHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing High Temp Alarm present. DCR 2%, number of drops 30/day. Could be related to 3G co-site.QLD 007061/18/1303-2013GTBH1404302404302_Beenleigh_1404302_Beenleigh_MO_G09A_3KPI DegradationRetainabilityFDDQMIN65Retaining border traffic(likely to be dropped) on 2G moreHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing High Temp Alarm present. DCR 2%, number of drops 30/day. Could be related to 3G co-site.QLD 007071/18/1303-2013GTBH1410122410122_Beenleigh_1410122_Beenleigh_MV_G09A_1KPI DegradationRetainabilityFDDQMIN65Retaining border traffic(likely to be dropped) on 2G moreHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedUnable to query any stats in PRS, Site should be 4302QLD 007081/18/1303-2013GTBH1410122410122_Beenleigh_1410122_Beenleigh_MV_G09A_3KPI DegradationRetainabilityFDDQMIN65Retaining border traffic(likely to be dropped) on 2G moreHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedUnable to query any stats in PRS, Site should be 4302QLD 007091/18/1303-2013BERH3409315409315_Beenleigh_253154409315_Beenleigh_MO_U21B_1KPI DegradationRetainabilityINTERRATCSTHD2DECN0-16-15Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 2%. Number of drops approx 100/dayQLD 007101/18/1303-2013BERH3409315409315_Beenleigh_253156409315_Beenleigh_MO_U21B_3KPI DegradationRetainabilityINTERRATCSTHD2DECN0-16-15Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in DCR around 29th Jan from 3% to approx 1% in feb. Number of drops reduced from 30/day to 5/day. Ok to leaveQLD 007111/18/1303-2013BERH3409315409315_Beenleigh_253157409315_Beenleigh_MO_U21A_1KPI DegradationRetainabilityINTERRATCSTHD2DECN0-16-15Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 1.25%, drops about 60/day.QLD 007121/18/1303-2013BERH3409315409315_Beenleigh_253159409315_Beenleigh_MO_U21A_3KPI DegradationRetainabilityINTERRATCSTHD2DECN0-16-15Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in drops from 1.5 in jan to 0.75% approx. Reduction in drops from around 30 /day to 15/day. Okay to leaveQLD 007131/18/1303-2013BERH3404302404302_Beenleigh_255681404302_Beenleigh_MV_U08A_1KPI DegradationRetainabilityINTERRATCSTHD2DECN0-16-15Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007141/18/1303-2013BERH3404302404302_Beenleigh_255683404302_Beenleigh_MV_U08A_3KPI DegradationRetainabilityINTERRATCSTHD2DECN0-16-15Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007151/18/1303-2013BERH3409315409315_Beenleigh_253154409315_Beenleigh_MO_U21B_1KPI DegradationRetainabilityINTERRATCSTHD2FECN0-14-13Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 2%. Number of drops approx 100/dayQLD 007161/18/1303-2013BERH3409315409315_Beenleigh_253156409315_Beenleigh_MO_U21B_3KPI DegradationRetainabilityINTERRATCSTHD2FECN0-14-13Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in DCR around 29th Jan from 3% to approx 1% in feb. Number of drops reduced from 30/day to 5/day. Ok to leaveQLD 007171/18/1303-2013BERH3409315409315_Beenleigh_253157409315_Beenleigh_MO_U21A_1KPI DegradationRetainabilityINTERRATCSTHD2FECN0-14-13Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 1.25%, drops about 60/day.QLD 007181/18/1303-2013BERH3409315409315_Beenleigh_253159409315_Beenleigh_MO_U21A_3KPI DegradationRetainabilityINTERRATCSTHD2FECN0-14-13Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. Reduction in drops from 1.5 in jan to 0.75% approx. Reduction in drops from around 30 /day to 15/day. Okay to leaveQLD 007191/18/1303-2013BERH3404302404302_Beenleigh_255681404302_Beenleigh_MV_U08A_1KPI DegradationRetainabilityINTERRATCSTHD2FECN0-14-13Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007201/18/1303-2013BERH3404302404302_Beenleigh_255683404302_Beenleigh_MV_U08A_3KPI DegradationRetainabilityINTERRATCSTHD2FECN0-14-13Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007211/18/1303-2013BERH3409315409315_Beenleigh_253154409315_Beenleigh_MO_U21B_1KPI DegradationRetainabilityINTERRATCSTHD2DRSCP-110-107Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 2%. Number of drops approx 100/dayQLD 007221/18/1303-2013BERH3409315409315_Beenleigh_253156409315_Beenleigh_MO_U21B_3KPI DegradationRetainabilityINTERRATCSTHD2DRSCP-107-107Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedMistake. Ok leaveQLD 007231/18/1303-2013BERH3409315409315_Beenleigh_253157409315_Beenleigh_MO_U21A_1KPI DegradationRetainabilityINTERRATCSTHD2DRSCP-110-107Triggering timely IRAT measurementHasaanApprovedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.Approved but awaiting for ImplementationLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 1.25%, drops about 60/day.QLD 007241/18/1303-2013BERH3409315409315_Beenleigh_253159409315_Beenleigh_MO_U21A_3KPI DegradationRetainabilityINTERRATCSTHD2DRSCP-107-107Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedMistake. Ok leaveQLD 007251/18/1303-2013BERH3404302404302_Beenleigh_255681404302_Beenleigh_MV_U08A_1KPI DegradationRetainabilityINTERRATCSTHD2DRSCP-110-107Triggering timely IRAT measurementHasaanApprovedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.Approved but awaiting for ImplementationOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007261/18/1303-2013BERH3404302404302_Beenleigh_255683404302_Beenleigh_MV_U08A_3KPI DegradationRetainabilityINTERRATCSTHD2DRSCP-110-107Triggering timely IRAT measurementHasaanApprovedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.Approved but awaiting for ImplementationOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007271/18/1303-2013BERH3409315409315_Beenleigh_253154409315_Beenleigh_MO_U21B_1KPI DegradationRetainabilityINTERRATCSTHD2FRSCP-107-104Triggering timely IRAT measurementHasaanApprovedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.Approved but awaiting for ImplementationLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 2%. Number of drops approx 100/dayQLD 007281/18/1303-2013BERH3409315409315_Beenleigh_253156409315_Beenleigh_MO_U21B_3KPI DegradationRetainabilityINTERRATCSTHD2FRSCP-104-104Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedMistake. Ok leaveQLD 007291/18/1303-2013BERH3409315409315_Beenleigh_253157409315_Beenleigh_MO_U21A_1KPI DegradationRetainabilityINTERRATCSTHD2FRSCP-107-104Triggering timely IRAT measurementHasaanApprovedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.Approved but awaiting for ImplementationLast Maintenance link alarm was present on 7th/8th Feb. DCR is still approx 1.25%, drops about 60/day.QLD 007301/18/1303-2013BERH3409315409315_Beenleigh_253159409315_Beenleigh_MO_U21A_3KPI DegradationRetainabilityINTERRATCSTHD2FRSCP-104-104Triggering timely IRAT measurementHasaanRejectedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.RejectedMistake. Ok leaveQLD 007311/18/1303-2013BERH3404302404302_Beenleigh_255681404302_Beenleigh_MV_U08A_1KPI DegradationRetainabilityINTERRATCSTHD2FRSCP-107-104Triggering timely IRAT measurementHasaanApprovedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.Approved but awaiting for ImplementationOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007321/18/1303-2013BERH3404302404302_Beenleigh_255683404302_Beenleigh_MV_U08A_3KPI DegradationRetainabilityINTERRATCSTHD2FRSCP-107-104Triggering timely IRAT measurementHasaanApprovedThe retainability went bad from 9 Jan 2013 onwards. This was impacted by the call re-establishement timer reduction and selection/reselection modification CR's done on BERH3 basically increasing coverage for 3G. Site also has recurring hardware and transmission alarms. There was also an instance back in december where we had to reduce power on U850 due to outage on U2100 due to transmission fault. The U850 power have been set back to normal last 29Jan. I suggest we look into the clearing the alarms or any hardware fault before we modify the parameters. We can also look at reverting the selection/reselection modifications done.Approved but awaiting for ImplementationOngoing SCTP Link alarms . Need to check links. Drops are high. With recent adverse weather it is hard to tell, whether it is weather related or real link issue. Will need to investigate further.QLD 007381/25/1304-2013GTRH1404020404020_SpringHill_255951404020_SpringHill_MV_U08A_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-16-15Encourage timely interfreq HOPerformance StableStableHasaanApprovedIncrease in drops after CR to modify cell selection/reselection and TRL timer. This is possibly inter-freq neigh missing. Added interfreq neigh (04/02). If still bad possibly revert selection/reselection modification.Implemented2/22/13QLD 007391/25/1304-2013GTRH1404020404020_SpringHill_255951404020_SpringHill_MV_U08A_1KPI DegradationRetainabilityINTERFREQCSTHD2DRSCP-110-109Encourage timely interfreq HOPerformance StableStableHasaanApprovedIncrease in drops after CR to modify cell selection/reselection and TRL timer. This is possibly inter-freq neigh missing. Added interfreq neigh (04/02). If still bad possibly revert selection/reselection modification.Implemented2/22/13QLD 007401/25/1304-2013BERH3409225409225_WaterfordWest_252256409225_WaterfordWest_MO_U21B_3KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-14-13Encourage timely interfreq HOPerformance StableStableHasaanApprovedIncrease in drops after CR to modify cell selection/reselection and TRL timer. This is possibly inter-freq neigh missing. Added interfreq neigh (05/02). If still bad possibly revert selection/reselection modification.Implemented2/22/13QLD 007411/25/1304-2013BERH3409225409225_WaterfordWest_252256409225_WaterfordWest_MO_U21B_3KPI DegradationRetainabilityINTERFREQCSTHD2DRSCP-110-107Encourage timely interfreq HOPerformance StableStableHasaanApprovedIncrease in drops after CR to modify cell selection/reselection and TRL timer. This is possibly inter-freq neigh missing. Added interfreq neigh (05/02). If still bad possibly revert selection/reselection modification.Implemented2/22/13QLD 007421/25/1304-2013BERH3409225409225_WaterfordWest_252256409225_WaterfordWest_MO_U21B_3KPI DegradationRetainabilityINTERFREQCSTHD2FRSCP-107-104Encourage timely interfreq HOPerformance StableStableHasaanApprovedIncrease in drops after CR to modify cell selection/reselection and TRL timer. This is possibly inter-freq neigh missing. Added interfreq neigh (05/02). If still bad possibly revert selection/reselection modification.Implemented2/22/13QLD 007431/25/1304-2013BERH3409244409244_Loganholme_252444409244_Loganholme_MO_U21B_1KPI DegradationRetainabilityINTERFREQCSTHD2DECN0-14-13Encourage timely interfreq HOPerformance StableStableHasaanRejectedChanges recommended will have an impact to coverage. Recent stats shows retainability has improvedImplemented2/22/13Last alarm was on 8th Feb, link failure. DCR has come down from 4.5% to 2.5%, from 50/day to 20/day. Could be related to 4302 issue. Leave for nowQLD 007441/25/1304-2013BERH3409244409244_Loganholme_252444409244_Loganholme_MO_U21B_1KPI DegradationRetainabilityINTERFREQCSTHD2DRSCP-110-107Encourage timely interfreq HOPerformance StableStableHasaanRejectedChanges recommended will have an impact to coverage. Recent stats shows retainability has improvedImplemented2/22/13Last alarm was on 8th Feb, link failure. DCR has come down from 4.5% to 2.5%, from 50/day to 20/day. Could be related to 4302 issue. Leave for nowQLD 007481/31/1305-2013BERH1404327404327_Coolum57791404327_Coolum_MV_U08A_1Trigger for OptiRetainabilityQrxlevmin-58-57High number of drops.Performance StableStableDhirenApprovedWe can do this in the interim to reduce the coverage as this is an omni site. But long term solution is to do sectorization on this site. This site is using an old antenna (CellWave_PD1109A) with no control over the tilt.Implemented2/21/13QLD 007491/31/1305-2013BERH1404327404327_Coolum57791404327_Coolum_MV_U08A_1Trigger for OptiRetainabilityQqualmin-18-17High number of drops.Performance StableStableDhirenApprovedWe can do this in the interim to reduce the coverage as this is an omni site. But long term solution is to do sectorization on this site. This site is using an old antenna (CellWave_PD1109A) with no control over the tilt.Implemented2/21/13QLD 007501/31/1305-2013BERH1404329404329_Nambour_256006404329_Nambour_MX_U21A_3Trigger for OptiRetainabilitySSEARCHRAT13High number of drops. Encouraging IRAT HOPerformance StableStableDhirenRejectedThis should be alright as there is no congestion in the area. But based from Nastar this cell is propagating up to 5kms. RSCP is marginal within around 2km of the site. I added potential missing inter and intra neighbours.Implemented2/22/13DCR is about 2.5%, has come down slightly from 3%, Number of drops are 25/day, used to be 7/day pre timer changes. Should be implemented QLD 007511/31/1305-2013BERH1404329404329_Nambour_256006404329_Nambour_MX_U21A_3Trigger for OptiRetainabilityINTERRATCSTHD2DECN0-16-15High number of drops. Encouraging IRAT HOPerformance StableStableDhirenRejectedThis should be alright as there is no congestion in the area. But based from Nastar this cell is propagating up to 5kms. RSCP is marginal within around 2km of the site. I added potential missing inter and intra neighbours.Implemented2/22/13DCR is about 2.5%, has come down slightly from 3%, Number of drops are 25/day, used to be 7/day pre timer changes. Should be implemented QLD 007521/31/1305-2013BERH1404329404329_Nambour_256006404329_Nambour_MX_U21A_3Trigger for OptiRetainabilityINTERRATCSTHD2DRSCP-111-109High number of drops. Encouraging IRAT HOPerformance StableStableDhirenRejectedThis should be alright as there is no congestion in the area. But based from Nastar this cell is propagating up to 5kms. RSCP is marginal within around 2km of the site. I added potential missing inter and intra neighbours.Implemented2/22/13DCR is about 2.5%, has come down slightly from 3%, Number of drops are 25/day, used to be 7/day pre timer changes. Should be implemented QLD 007602/8/1306-2013BERH1404337404337_Gympie_255130404337_Gympie_MX_U09_0S/w & H/w ConfigurationRTWPTMA off and attenuation setting not defined.TMA activated and attenuation settings correctedHigh RTWP, -94dBm, Alarms present All RTWP/RSSI unbalanced Performance improved: RTWP has improved to -104dBm. Alarm clearedImprovement in KPIDhirenPerformance improved: RTWP has improved to -104dBm. Alarm clearedApprovedImplemented2/6/12QLD 007612/8/1306-2013GTRH2404870404870_WstfldCarindale_256429404870_WstfldCarindale_IO_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007622/8/1306-2013GTRH2404870404870_WstfldCarindale_256428404870_WstfldCarindale_IO_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007632/8/1306-2013GTRH2404870404870_WstfldCarindale_256427404870_WstfldCarindale_IO_U08A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007642/8/1306-2013GTRH2409001409001_DomesTerminals_250017409001_DomesTerminals_IO_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007652/8/1306-2013GTRH2409001409001_DomesTerminals_250014409001_DomesTerminals_IO_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007662/8/1306-2013GTRH2409002409002_IntlTerminals_250024409002_IntlTerminals_IO_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007672/8/1306-2013GTRH2409002409002_IntlTerminals_250025409002_IntlTerminals_IO_U21B_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007682/8/1306-2013GTRH2409382409382_ChermsideSC_253827409382_ChermsideSC_IV_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007692/8/1306-2013GTRH2409382409382_ChermsideSC_253828409382_ChermsideSC_IV_U21A_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007702/8/1306-2013GTRH2409382409382_ChermsideSC_253829409382_ChermsideSC_IV_U21A_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007712/8/1306-2013GTRH2409382409382_ChermsideSC_253824409382_ChermsideSC_IV_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007722/8/1306-2013GTRH2409382409382_ChermsideSC_253825409382_ChermsideSC_IV_U21B_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007732/8/1306-2013GTRH2409382409382_ChermsideSC_253826409382_ChermsideSC_IV_U21B_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007742/8/1306-2013GTRH2409382409382_ChermsideSC_256187409382_ChermsideSC_IV_U08A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007752/8/1306-2013GTRH2409382409382_ChermsideSC_256188409382_ChermsideSC_IV_U08A_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007762/8/1306-2013GTRH2409382409382_ChermsideSC_256189409382_ChermsideSC_IV_U08A_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007772/8/1306-2013GTRH1404134404134_WFSCIndooroopil_255394404134_WFSCIndooroopil_IV_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007782/8/1306-2013GTRH1404134404134_WFSCIndooroopil_255395404134_WFSCIndooroopil_IV_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007792/8/1306-2013GTRH1404134404134_WFSCIndooroopil_255406404134_WFSCIndooroopil_IV_U08A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007802/8/1306-2013GTRH1404808404808_MyerCentreDAS_24638404808_MyerCentreDAS_IO_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007812/8/1306-2013GTRH1404808404808_MyerCentreDAS_24637404808_MyerCentreDAS_IO_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007822/8/1306-2013GTRH1404808404808_MyerCentreDAS_24519404808_MyerCentreDAS_IO_U08A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007832/8/1306-2013GTRH1404846404846_InnerCityBypass_256498404846_InnerCityBypass_IV_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007842/8/1306-2013GTRH1404846404846_InnerCityBypass_256497404846_InnerCityBypass_IV_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007852/8/1306-2013GTRH1404846404846_InnerCityBypass_256345404846_InnerCityBypass_IV_U08A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007862/8/1306-2013GTRH1404846404846_InnerCityBypass_256346404846_InnerCityBypass_IV_U08B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007872/8/1306-2013GTRH1404868404868_NthSthBypass_253887404868_NthSthBypass_IV_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007882/8/1306-2013GTRH1404868404868_NthSthBypass_253888404868_NthSthBypass_IV_U21A_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007892/8/1306-2013GTRH1404868404868_NthSthBypass_253889404868_NthSthBypass_IV_U21A_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007902/8/1306-2013GTRH1404868404868_NthSthBypass_253884404868_NthSthBypass_IV_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007912/8/1306-2013GTRH1404868404868_NthSthBypass_253885404868_NthSthBypass_IV_U21B_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007922/8/1306-2013GTRH1404868404868_NthSthBypass_253886404868_NthSthBypass_IV_U21B_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007932/8/1306-2013GTRH1404950404950_ToowongVillage_256208404950_ToowongVillage_IO_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007942/8/1306-2013GTRH1404950404950_ToowongVillage_256207404950_ToowongVillage_IO_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007952/8/1306-2013GTRH1404953404953_BrisbaneAportLk_255797404953_BrisbaneAportLk_IV_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007962/8/1306-2013GTRH1404953404953_BrisbaneAportLk_255798404953_BrisbaneAportLk_IV_U21A_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007972/8/1306-2013GTRH1404953404953_BrisbaneAportLk_255799404953_BrisbaneAportLk_IV_U21A_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007982/8/1306-2013GTRH1404953404953_BrisbaneAportLk_255794404953_BrisbaneAportLk_IV_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 007992/8/1306-2013GTRH1404953404953_BrisbaneAportLk_255795404953_BrisbaneAportLk_IV_U21B_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008002/8/1306-2013GTRH1404953404953_BrisbaneAportLk_255796404953_BrisbaneAportLk_IV_U21B_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008012/8/1306-2013GTRH1404953404953_BrisbaneAportLk_258841404953_BrisbaneAportLk_IV_U08A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008022/8/1306-2013GTRH1404953404953_BrisbaneAportLk_258842404953_BrisbaneAportLk_IV_U08A_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008032/8/1306-2013GTRH1404953404953_BrisbaneAportLk_258843404953_BrisbaneAportLk_IV_U08A_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008042/8/1306-2013GTRH1404953404953_BrisbaneAportLk_258847404953_BrisbaneAportLk_IV_U08B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008052/8/1306-2013GTRH1404953404953_BrisbaneAportLk_258848404953_BrisbaneAportLk_IV_U08B_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008062/8/1306-2013GTRH1404953404953_BrisbaneAportLk_258849404953_BrisbaneAportLk_IV_U08B_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008072/8/1306-2013GTRH1409710409710_GabbaCG_255127409710_GabbaCG_IV_U21A_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008082/8/1306-2013GTRH1409710409710_GabbaCG_255128409710_GabbaCG_IV_U21A_2AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008092/8/1306-2013GTRH1409710409710_GabbaCG_255129409710_GabbaCG_IV_U21A_3AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprovednot required, no impact on KPI's. MaxTxPower on NodeB and RNC is not required to be the same. Current setting is ok as long as the NodeB MaxTxPower is greater than or equal to RNC level MaxTxPower.RejectedConsistency In Settings Required. Email sent with explanation.QLD 008102/8/1306-2013GTRH1409710409710_GabbaCG_255124409710_GabbaCG_IV_U21B_1AuditProactive Measures MAXTXPOWERNAOn NodeB Level MAXTXPOWER=460On NodeB Level set MAXTXPOWER=430 to match MAXTXPOWER of 430 on RNC LevelMAXTXPOWER should be same for both.MubasharApprove