Parker Automation 402/403XE Introduction

Parker Hannifin Corporation

Parker Hannifin Corporation

Parker Hannifin Corporation

Parker Hannifin CorporationParker Hannifin

Pneumatics Division NA

Pneumatics Division Europe

Electromechanical Division NA

Electromechanical Division Europe

Actuator Division

Rohnert Park, CACompumotor

AcroloopCTC

Irwin, PADaedal

New Ulm, MNCustom Servo Motor

Compumotor

Cincinnati, OHCTC

Webster, TXTrilogy

Port Washington, NYBayside

Fluid Connectors

SealHydraulics InstrumentationAutomation

AerospaceCIC Filtration

Electromechanical Division – Irwin, PA Facility (Daedal)

Introducing the 402/403XE Series

What is the 402/403 XE series? • Value priced actuator for

medium payloads – (<150 lbs)

• Ideal for hard disk manufacturing, high tech markets, life sciences, lab automation, and also pneumatic replacements applications

402/403 XE Basics• Highly integrated linear rail/screw positioner

– Two cross sections (HxW)• 402XE – 23x50mm (no cover) and 36x57mm (cover)• 403XE – 30x60mm (no cover) and 45x80mm (cover)

– Extruded and machined steel base• 402XE – 75mm to 225 mm stroke• 403XE – 60mm to 655 mm stroke• Steel body allows for cantilever

– Precision rolled ballscrew• 402XE – 5mm or 2mm lead• 403XE – 5mm or 10mm lead

Rigid Steel U-Channel BodyProvides structural rigidity for minimal deflection.

Flexible Motor Mounting OptionsProvide a variety of motor drive options including servo and stepper motorsPrecision Ball Screw Drive

TrainProvides smooth motion with high accuracy and high mechanical efficiency.

Integrated Precision Screw and Guide BearingProvide a low profile, high accuracy, smooth motion, and robust adjustment free design over the life of the actuator

Packaged Adjustable Limit SensorsProvide adjustable stroke lengths, easily connected, and reduced cables to manage in an aesthetically appealing manner.Optional Hard Cover

Clear anodized Provides protection from contamination falling into the positioner.

402 /403 XE Series • Precision Rolled Ballscrew

– 5mm, 2mm lead options (402XE)– 5mm, 10mm lead options (403XE)

• +/-5 um repeatability– Accuracy ~ 15 um

402/403 XE Bearing

• Highly Integrated Linear Bearing– Single Carriage– 4 point contact for equal

loading in any direction

402/403 XE • Optional Hard

Cover– Similar to

404XE– Protection

from large contaminants

– approx. ~IP20

402/403XE Mounting • “Down through” style

– Repeatable mounting pattern– Utilized in both the 402 and

403• (Not identical)

– Allows user to bolt unit down within the footprint of the actuator body instead of making the unit wider with toe clamps.

402/403 XE Motor Options

• Stepper Motor Options– LV/HV17– LV/HV23

• Servo Motor Options– SM23– SM16

• Prepped for these motors or Included

402/403 XE Limits• Home and Limit Sensor

Option– Parker Global Sensor

– 24VDC operation

– NPN / PNP

– NO / NC options

– Packaged into limit switch

housing with connector terminal

– Same sensor as HD and LP actuators

Compared to 404XE404XE

403XE 402XE

404XE 403XE 402XE

Width 95mm 60mm 50mm

Height 47.3mm 30mm 23mm

Max Travel 700mm 655mm 220mm

Repeatability 20-30 micron +/-5 micron +/-5 micron

Straightness 20-30 micron 15-25 micron 15 micron

Load Capacity 135/270 lbs 425 lbs 261 lbs

Max Speed 1440 mm/s 810 mm/s 490 mm/sec

Leads 5, 10, 20mm 5, 10mm 2, 5mm

Compared to 401/402XR

402XR403XE 402XE

402XR 403XE 401XR 402XE

Width 57.1mm 60mm 40.9mm 50mm

Height 57.1mm 30mm 49.5mm 23mm

Max Travel 600mm 655mm 300mm 220mm

Repeat (+/-) 12 micron +/-5 micron 5-12 micron +/-5 micron

Straightness 20-30 micron 15-25 micron 20-25micron 15 micron

Load 220 lbs 425 lbs 110 lbs 261 lbs

Max Speed 1440 mm/s 810 mm/s 500 mm/sec 490 mm/sec

Leads 5, 10mm 5, 10mm 2, 5mm 2, 5mm

401XR

• 4 travel options

• 2 Drive styles (2 or 5 mm)

• Connectorized or Hard wired limits

• Flexible motor mounts or include the SM16 or HV23

• Hard cover and Clean Room options

• XY assembly for system solutions

Same as 402 except:• 8 Travel options

• 5 or 10 mm lead screw

• SM232 motor option included

Lower Cost of Ownership vs B.Y.O.• Buy a screw – Design time, Find a Screw, Find Competitive Priced

Screw, Time for Quote Response, Revisions ~ $250• Buy a motor – Design time, Find a Motor, Find Competitive Priced

Motor, Time for Quote Response, Revisions ~ $150-$700 depending on Stepper or Servo.

• Buy limit sensors – Design time, Find Sensors, Find Competitive Priced Sensors, Time for Quote Response, Revisions ~ $80

• Buy bearing set – D.T., Find Bearings, Find Competitive Priced Bearings, Time for Quote Response, Revisions ~ $150

• Stock everything after receipt - $30• Machine body - $70• Machine motor mounts - $50• Annodize components - $60-150 depending on your lot charge• Pick the job BOM complete and report shortages - $20• Assemble your components - $35• Test and debug design capabilities - $120

= $ 1015 - $1635

Lower Risk option than B.Y.O. • One Point of Contact to expedite orders• One Company to look to for support (no finger pointing)• One item to stock (less exposure to inventory issues)• Worldwide Support from Parker for machines shipped anywhere (on

the globe)• Custom Systems, Plates, Solutions utilizing Parker’s Engineers• What is the positioners repeatability spec? How many do you have

to build to have a 95% confidence level in this value? • What happens if your low cost bearing supplier has a quality issue

with their overseas imports?

Questions?