Part Design V5R8 Update

8/11/2019 Part Design V5R8 Update

1/19

Copyright DASSAULT SYSTEMES 2002 1

Part Design V5R8Update

CATIA Training Foils

Version 5 Release 8January 2002

EDU-CAT-E-PDG-UF-V5R8


2/19


Table of Contents

1. Sketch Based Features p.3Multi-length Pad p.4

Multi-length Pocket p.7

2. Dress up Features p.10Extracting Geometry p.11Shell Update p.13

3. Part Management p.15Change Boolean Type p.16


3/19


Sketch Based Features

You w il l see wh at is new and has been enhanced in CA TIA V5R8 for Pad and

Pocke t in the Par t Des ign Workbench

Multi-length PadMulti-length Pocket


4/19


Multi-length Pad (1/3) You can extrude multiple profiles belonging to a same sketchusing different length values. The multi-pad capability lets youdo this at one time.

V5R8

Select the Multi-lengthpad icon

The Pad Definition dialogbox is displayed. You cansee the number of domainsto be extruded.

1

2 Select the Sketch.Note that all profilesmust be closed andmust not intersect.

3


5/19Copyright DASSAULT SYSTEMES 2002 5

Multi-length Pad (2/3) You can extrude multiple profiles belonging to a same sketch using different length values.The multi-pad capability lets you do this at one time.

V5R8

A red arrow is displayed normal tothe sketch. It indicates the proposedextrusion direction. To reverse it,you just need to click it.

45 Select a Domain in the list. This one now

appears in blue in the geometry area.



Multi-length Pad (3/3) You can extrude multiple profiles belonging to a same sketch using different length values. The multi-pad capability lets you do this at one time.

V5R8

Specify the length by entering a value.For example, enter 20mm. Repeat theoperation for each extrusion domain.

67

Click OK to create the Multi-heightPad.

Note that you can multiselectextrusion domain from thelist before defining a

common length or thickness.



Multi-length Pocket (1/3) You can extrude multiple profiles belonging to a same sketch using different length values. Themulti-pocket capability lets you do this at one time.

V5R8

Select the Multi-lengthpad icon

The Pocket Definitiondialog box is displayed. Youcan see the number ofdomains to be extruded.

1

2 Select the Sketch.Note that all profilesmust be closed andmust not intersect.

3

Note that a red arrow is displayednormal to the sketch. It indicates theproposed extrusion direction. Toreverse it, you just need to click it.



Multi-length Pocket (2/3) You can extrude multiple profiles belonging to a same sketch using different length values. Themulti-pocket capability lets you do this at one time.

V5R8

4

5

Select a Domain in the list. This one nowappears in blue in the geometry area.

Specify the length by entering a value.

For example, enter 10mm. Repeat theoperation for each extrusion domain.

Note that you can multiselectextrusion domain from thelist before defining acommon length or thickness.


9/19



Dress up Features

You w il l see w hat is new and h as been enhanc ed in CATIA V5R8 for Draft in

the Par t Des ign Workb ench

Extracting geometry

Shell Update



Extracting Geometry (1/2)The Extract capability lets you generate separate elements from initial geometry, without deletinggeometry. This operation may be especially useful to solve difficulties when drafting for example.

Use the Draft command to draft thepad with 10 as angle value forexample.

1

2 Once done, the application informsyou that the operation cannot beproperly achieved.

Click OK to close the error message3



Extracting Geometry (2/2)

A new dialog box displays providing you with asolution. You can deactivate the draft and extract itsgeometry. To do so, click Yes.

The Extract capability lets you generate separate elements from initial geometry, without deletinggeometry. This operation may be especially useful to solve difficulties when drafting for example.

4 5 Draft.1 appears as deactivated in the specificationtree. A node "Extracted Geometry" is displayed inthe tree too. This category includes the elementscreated by the application, namely five surfaces.

You can now use Generative ShapeDesign capabilities to complete thedraft.

V5R8

V5R8



Shell Update (1/2)After a sketch modification, a text is displayed about the previousface.

Enter the Sketcher to replace the circular edge ofthe initial sketch with a line, then return to PartDesign.

1

2Then, close the Update Diagnosis dialog box.



Shell Update (2/2)After a sketch modification, a text is displayed about the previous face.

Double-click on Shell.1 in the Specification Tree. The FeatureDefinition Error window displays, prompting you to changespecifications. Moreover, the old face you have just deleted isnow displayed in yellow. Click OK to close the window. The ShellDefinition dialog box appears.

3V5R8

Note that the text "Removed Face" is displayed close to the face,thus giving you a better indication of the face that has beenremoved.

4 Click the Faces to remove field if not already done and selectthe replacing face. Click OK to close the Shell Definition dialogbox and obtain a correct part. The shell feature is rebuilt.


15/19


Part Management

You w i l l see what i s new and has b een enhanced in CATIA V5R8 for

Managing B odies in the Par t Des ign Wo rkbench

Change Boolean Type


16/19


Change Boolean Type (1/4)The initial part is composed of three

bodies. Assemble Body.1 to PartBody.

1

Remove Body.2 from Assemble.1.You obtainRemove.1.

2

V5R8

V5R8


17/19


Change Boolean Type (2/4)

Click with the right button mouse onRemove.1. In the contextual menu,select Remove.1 object

3

V5R8

Choose now the new operation. Forexample, click on Change ToAssemble .

4


18/19



You obtain :5

V5R8

Change now Assemble.2 to UnionTrim. You obtain :

6


19/19



You can edit Trim.1 . For instance,select the cylinder's top face as the

face to keep. You obtain :

7

V5R8

Date post:	02-Jun-2018
Category:	Documents
Upload:	adi-fiera
View:	223 times
Download:	0 times

Part Design V5R8 Update

Documents