© 2019 American Honda Motor Co., Inc. – All Rights Re
VERSION 1Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
DECK LID SPOILERP/N 08F10-TY2-201
served. BII12560-04 (190
2020 RLX
7) 0
Issue Date
JUL 2019
PARTS LISTTrunk spoiler
Left trunk spring (marked yellow)
Right trunk spring (marked red)
Template A
Template B
4 Clip grommets
4 Pins
4 Seals
Alcohol swab
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriverFlat-tip screwdriverDrillEye protection (face shield, safety goggles, etc.)Center punchTouch-up paintFelt-tip penMasking tapeHeavy glovesRopeRulerThe following tools are available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.• Rubber Roller (T/N MHLE54D)• Rotabroach Hole Cutting Kit (T/N BLR11201SO)• Deburring Tool (T/N DEBUR300)
Illustration of the Trunk Spoiler on the Vehicle
QG30801AG
TRUNK SPOILER
1 of 108F10-TY2-2010-90
INSTALLATION
Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE:• Be careful not to damage the paint finish.• This deck lid spoiler kit should be installed only if the
ambient air temperature is 15°C (60°F) or above.• Clean the areas to be covered.• To allow the adhesive to cure, do not wash the vehicle
for 24 hours. Make sure your client is aware of this.1. Open the trunk lid. Remove trunk floor cover.
QB42001AK
TRUNK LID
TRUNK FLOOR COVER
2 of 10 BII12560-0
2. Remove the trunk tool box.
QB42002AK
TRUNK TOOL BOX
3. Remove the trunk rear trim panel
QB42003BK
6 CLIPS TRUNK REAR TRIM PANEL
HOOK
HOOK
HOOK
4 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
4. Remove the two tie down hooks.• Wrap masking tape around the tip of flat-tip
screwdriver.• Open the covers.• Remove the two screws.
QB42004AK
FLAT-TIP SCREWDRIVER
2 TIE DOWN HOOKS 4 RETAINING
TABS COVERS
2 SCREWS
MASKING TAPE
5. Pull away the weatherstrip, and remove the right trunk side trim.
QB42005CK
3 HOOKS
RIGHT TRUNK SIDE TRIM
2 CLIPS
WEATHERSTRIP (Pull away.)
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII12560-0
6. Remove the two tie down hooks.• Wrap masking tape around the tip of flat-tip
screwdriver.• Open the covers.• Remove the two screws.
QB42501AK
FLAT-TIP SCREWDRIVER
4 RETAINING TABS COVERS
2 SCREWS
2 TIE DOWN HOOKS
MASKING TAPE
7. Pull away the weatherstrip, and remove the left trunk side trim.
QB42502CK
3 HOOKS
LEFT TRUNK SIDE TRIM
2 CLIPS
WEATHERSTRIP (Pull away.)
4 (1907) 3 of 10
8. Close the trunk lid. Attach the strips of masking tape to the trunk lid as shown.
QB42601AK
TRUNK LID
MASKING TAPE
MASKING TAPE
9. Line up the template A to the trunk lid as shown, and attach it with masking tape.
QB42602AK
TRUNK LID
TRUNK LIDLine up.SECTION VIEW
TEMPLATE A
Line up.
TEMPLATE A
MASKING TAPE
4 of 10 BII12560-0
10. Using a felt-tip pen, mark two points through the template A as shown. Remove the template A.
QB42603AK
FELT-TIP PEN
TRUNK LID
2 POINTS
TEMPLATE A
11. Turn the template A over, and repeat steps 9 and 10 on the right side of the trunk lid.
12. Using a center punch, punch the centers of the four marks. Set the center punch to the minimum power setting.
QB42604AK
CENTER PUNCH
TRUNK LID
4 MARKS
4 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
13. While wearing eye protection, drill four 8.5 mm holes at the marks with a 8.5 mm Rotabroach bit. Drill perpendicular to the trunk lid. Remove the masking tape attached in step 8.
QB42605AK
4 MARKS
TRUNK LID
DRILL(8.5 mm ROTABROACH BIT)
TRUNK LID
Drill perpendicular.
14. Using a deburring tool, remove all burrs from the holes.NOTE: To ensure proper clip engagement, be sure to remove any metal shavings or burrs.
QG41701AN
DEBURRING TOOL
4 HOLESSECTION VIEW
Incorrect.
HOLETRUNK LID
TRUNK LID
15. Apply touch-up paint to the edges of the holes and allow the touch-up paint to dry.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII12560-0
16. Line up the template B to the trunk lid as shown, and attach it with masking tape.
QG30802BG
TEMPLATE BLine up with the edges of the trunk lid. TRUNK LID
MASKING TAPE
TEMPLATE B
TRUNK LIDLine up.
SECTION VIEW
TEMPLATE B
TRUNK LID
17. Using an alcohol swab, thoroughly clean the area where the trunk spoiler will attach. Be sure to allow the alcohol to fully dry before installing the spoiler.NOTE: Any oil or dirt remaining on the trunk lid will affect the performance of the adhesive tape, which could cause gaps or spoiler lifting.
QG30803AG
ALCOHOL SWAB
TRUNK LID(Clean with the alcohol swab.)
4 (1907) 5 of 10
18. Install the four seals to the four clip grommets.
872756AH
4 SEALS
4 CLIP GROMMETS
19. Install the four clip grommets to the four holes on the trunk lid. NOTE: To confirm clip engagement, listen for the “click” sound during installation.
QG30804AG
4 CLIP GROMMETS
Incorrect.
4 HOLES
4 CLIP GROMMETS 8 RETAINING
TABS
TRUNK LID
2 RETAINING TABS
CLIP GROMMET
SECTION VIEW
TRUNK LID
Incorrect.
6 of 10 BII12560-0
20. Install the four pins to the trunk spoiler as shown.
QG30805CG4 PINS
TRUNK SPOILER
TRUNK SPOILER
PROJECTIONS
4 PINS
21. Peel back the adhesive backings, and tape the ends to the front surface of the trunk spoiler.
QG30806BG
MASKING TAPE
TRUNK SPOILER2 ADHESIVE BACKINGS
ADHESIVE BACKING (Remove.)
MASKING TAPE
8 ADHESIVE BACKINGS
ADHESIVE BACKING (Remove.)
22. Remove the remaining adhesive backings.
4 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
23. Line up the trunk spoiler with the template B. Install the trunk spoiler to the four clip grommets with the four pins. Pushing the spoiler may be necessary to properly align it to template B.NOTE: To confirm clip engagement, listen for the “click” sound during installation. Using your hands, lift up on the clip area of the spoiler to confirm the clips are fully engaged.
QG30807CG
4 PINS
TRUNK LID
TRUNK LID
Incorrect.
4 CLIP GROMMETS
TEMPLATE B
TRUNK SPOILER
Line up.
TRUNK SPOILER
SECTION VIEW
TEMPLATE B
TRUNK SPOILER
TRUNK LID
TRUNK SPOILER
Push. Push.Push.
Incorrect.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII12560-0
24. Adjust the position of the trunk spoiler as shown.
QG30808AG
TRUNK LID
TRUNK SPOILER
Equal spacing on both sides. TRUNK LID
5 mm(0.20 in.)
TRUNK SPOILER
Equal spacing.
4 (1907) 7 of 10
25. While applying light pressure against the trunk spoiler, carefully remove the lower adhesive backings in the order shown.
QG30809DG
4 LOWER ADHESIVE BACKINGS(Remove.)
TRUNK SPOILERTRUNK LID
21
1
2
TRUNK SPOILER
TRUNK LIDPush.
SECTION VIEW
8 of 10 BII12560-0
26. While applying light pressure against the trunk spoiler, carefully remove the center adhesive backings.
QG30810CG
2 CENTER ADHESIVE BACKINGS(Remove.)
TRUNK SPOILER
TRUNK LID
TRUNK SPOILER
TRUNK LIDSECTION VIEW
Push.
27. While applying light pressure against the trunk spoiler, carefully remove the outer adhesive backings.
QG30811AG
2 OUTER ADHESIVE BACKINGS(Remove.)
TRUNK SPOILER
TRUNK LID
4 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
28. While applying light pressure against the trunk spoiler, carefully remove the middle adhesive backings.
QG30812AG
2 MIDDLE ADHESIVE BACKINGS(Remove.)
TRUNK SPOILER
TRUNK LID
29. Using your hand, firmly press the trunk spoiler against the trunk lid for 30 seconds.
30. Using a rubber roller, apply firm pressure, especially at the ends, to set the adhesive. Remove the template B.
QG30813AG
TRUNK LIDRUBBER ROLLER
TRUNK SPOILER
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII12560-0
31. Open the trunk lid. Put on heavy gloves to protect your hands. Using a piece of rope, remove the left trunk spring as shown. Pull the rope slowly and carefully toward you.
NOTICE: The trunk lid may fall by its own weight when the trunk springs are removed, and can cause injury. When installing and removing the trunk springs, have an assistant hold the trunk lid open, or secure it open with a block, etc.
QB50703BK
LEFT TRUNK SPRING
LEFT SIDE TRUNK LID HINGEROPE
VEHICLE PANEL
4 (1907) 9 of 10
32. Remove the sponge and clip from the left trunk spring. Attach the sponge and clip to the new left trunk spring (marked yellow) as shown.
QB50704AK
LEFT TRUNK SPRING(Do not reuse.)
CLIP
SPONGE
MARKED YELLOWNEW LEFT TRUNK SPRING
33. Install the new left trunk spring (marked yellow) in the reverse order of removal.
NOTICE: Be careful when installing the trunk spring as they repel with strong force and can cause injury.
QB50705AK
MARKED YELLOW
LEFT SIDE TRUNK LID HINGE
ROPE
NEW LEFT TRUNK SPRING
34. Repeat steps 31 through 33 on the new right trunk spring (marked red).
35. Install all removed parts.
10 of 10 BII12560-0
4 (1907) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.